LG | LWB18C1AM1 | LG LWB18C1AM1 Owner’s Manual

PLEASE INSTALL YOUR AIR CONDITIONER BY COMPANY
AUTHORISED SERVICE FRANCHISEE / AUTHORISED SALES
& SERVICE DEALER*
(*Please check Warranty Terms in Owner's Manual)
Room Air Conditioner
(Window Type)
OWNER'S MANUAL
CONTENTS
Safety precautions
Safety Precautions .......................................................................................................3
Operating instructions
Caution while operating Air Conditioner .......................................................................4
About the Controls on the Air Conditioner ....................................................................5
Care and Maintenance .................................................................................................9
Installation Instructions
Features.......................................................................................................................10
Installation Instructions.................................................................................................11
Troubleshooting tips
Before You Call for Service..........................................................................................12
10 Easy steps to find AC Tonnage .............................................................................13
-2-
FOR YOUR RECORDS
Write the model and serial numbers here:
Model #
Serial #
You can find them on a label on the side of each unit.
Dealer's Name
Date Purchased
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little
preventive care on your part can save you a great deal of time and money over the life of your air conditioner.
You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of
Troubleshooting Tips first, you may not need to call for service at all.
CAUTION
Contact the authorized service technician for repair or maintenance of this unit.
Contact the authorised dealer for installation of this unit.
The air conditioner is not intended for use by young children or infirm persons
without supervision.
Young children should be supervised to ensure that they do not play with the
air conditioner.
Safety Precautions
To prevent injury to the user or other people and property damage, the following instructions must be followed.
Incorrect operation due to ignoring of instruction will cause harm or damage, the seriousness is classified
by the following indications.
Plug in the power plug
properly.
Otherwise, it will cause electric
shock or fire due to heat
generation or electrical shock.
Do not modify power cord
length or share the outlet
with other appliances.
It will cause electrical shock or
fire due to heat generation.
Do not operate or stop the
unit by inserting or pulling
out the power plug.
It will cause electrical shock or fire
due to heat generation.
Do not operate with wet
hands or in damp
environment.
It may cause electrical shock.
-3-
Do not damage or use an
unspecified power cord.
It will cause electrical shock or fire.
If the supply cord is damaged, it
must be replaced by a special cord
or assembly available from the
manufacturer or its service agent.
Do not direct airflow at room
occupants only.
This could damage your health.
CAUTION WHILE OPERATING AC
Never touch the metal parts
of the unit when removing
the filter.
It may cause an injury.
When cleaning the unit, first
make sure the power and
breaker are turned off.
Since the fan rotates at high
speed during operation, it may
cause an injury.
Do not operate Switches
with wet hands.
It may cause an electric shock.
Do not clean the air
conditioner with water.
Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
Do not put a pet or house
plant where it will be
exposed to direct air flow.
This could injure the pet or plant.
Ventilate well when used
together with a stive, etc.
An oxygen shortage may occur.
Do not use for special
purposes.
Do not use this air conditioner to
preserve precision devices, food,
pets, plants, and art objects.
It may cause deterioration of
quality, etc.
Do not apply an insecticide
or flammable spray.
Do not put a heater, etc.
where is exposed to direct air
flow.
It may cause a fire or deformation
of the cabinet.
It may cause imperfect
combustion.
-4-
About the Controls on the air conditioner
TEMPERATURE
Off
On Med
Fan
Cool
Coolest
Wait for 3 minutes before restart
Off
6
4
High
Cool
Low
Cool
Auto Swing
5
Med
Cool
Off
Off
8
1
Cool
Low
Fan
9
Coolest
Wait for 3 minutes before restart
Cooling Model (Fig.1)
High
Cool
Med
On
Fan
7
3
2
Low
Fan
Operation
Thermostat
OPERATION
AUTO SWING
Med
Cool
Low
Cool
Cooling Model (Fig.2)
OFF: Stop all operation.
FAN: Circulates filtered air.
LOW COOL: Switches on the compressor and air
cooling operation at low fan speed.
MEDIUM COOL: Switches on the Compressor and
air cooling operation at medium fan speed.
.
HIGH COOL: Switches on the compressor
and air cooling operation at high fan speed.
LOW FAN: Circulates filtered at low
speed.
MED FAN: Circulates filtered air at
medium speed.
NOTE: If you move the switch from a cool setting to off or to a fan setting, wait at least 3
minutes before switching back to a cool setting.
the highest number available on your
Thermostat/temperarure
knob(position 6~9 in fig.2)
For Quieter & Nighttime Cooling
Select Low Cool with the
OPERATION knob at the midpoint of
Thermostat / Temperature
knob(position 1~4 in fig.2)
COOLING DESCRIPTIONS
For Normal Cooling- Select High Cool
or Med Cool with the OPERATION knob
at the midpoint of THER MOSTAT/
TEMPE RATURE knob(as mentioned in
fig.1 & fig.2)
For Maximum Cooling- Select High
Cool with the OPERATION knob at
THERMOSTAT (TEMPERATURE)
The THERMOSTAT/TEMPERATURE is used to maintain the room temperature. The
compressor will cycle on and off to keep the room at the same level of comfort.
When you turn the knob to a higher number (the right side) and the indoor air will
become cooler. The temperature is selected by turning the
Thermostat/temperature knob to the desired position.
The 5 or 6 position (the middle position of arc) is a normal setting for average
conditions.
-5-
Your Panel may look like any
of below mentioned panels.
2
3
Mode
Timer
Type 1
22
Cool
On
Dry
Energy Saver
FAN
SPEED
DOWN
V
Fan Speed
FAN SPEED
Cool
Type 2
7
ENERGY SAVER AUTO SWING
2( b)
V
V
TIMER COOLING/FAN
3
22
Timer
UP
FAN SPEED
4
6
5
Fan
DOWN
UP
5
Temp
4
1
1
5
1
ON/OFF
REMOTE CONTROLLER
POWER
POWER
7
AUTO
SWING
V
Fan
REMOTE CONTROLLER
2
3
6
2( b)
4
TIMER COOLING/FAN
2
ENERGY SAVER AUTO SWING
6
1
Temp
Power
5
7
FAN
Temp
TEMP
5
Power
1
5
ON
Timer
FAN
SPEED
AUTO
SWING
ON/OFF
V
(e) E N E R GY S AV E R
2
3
4
6
FAN
88
TEMP
Temp
9
2
Sleep
Mode
Timer
Auto
Swing
3
5
FAN SPEED
6
4
4
4
7
COOL
V
5
Fan Speed
Fan Speed
1
1
5
1
TEMP
Power
8
V
ENERGY SAVER
Mode
Type 4
Air
Purifier
V
DRY
Type 3
POWER
88
COOL
9
2
Sleep
Mode
Timer
Auto
Swing
3
6
MODE
2
AUTO SWING
6
ON/OFF
1
Controls
Precaution: The Remote Control unit will not function properly if strong light strikes the sensor
window of the air conditioner or if there are obstacles between the Remote Control
unit and the air conditioner.
1 POWER BUTTON
Operation starts, when this button is pressed and stops when you press the button again.
2 OPERATION MODE SELECTION BUTTON
Select (a)Cool (b)Energy Saver (c)Fan & (d)Dehumidification (dry) with this button.
Energy saver mode-fan stops when compressor stops cooling. Approximately after 3
minutes fan will turn on to determine it cooling is needed. In dry mode, unit will run at
low fan speed only with compressor ‘ON’.
-6-
3 ON/OFF TIMER
Set the time of on/off operation. The timer can be set by the one hour for a maximum of 12 hours.
In the first 30 minutes set temperature increases by 1°C and in the next 30 minutes temperature
increases by another 1°C, this temperature then remains till the timer function is deactivated.
4 FAN SPEED SELECTOR
Select the fan speed in Three steps Low (F1) / Med. (F2) / High (F3)
5 ROOM TEMPERATURE SETTING BUTTON
Control the room temperature within a range of 16°C to 30°C.
6 AUTO SWING
The vertical louver swings horizontally by the automatic system and stops when you press the
button again.
7 SIGNAL RECEIVER
8 AIR PURIFIER (For Plasma Model)
Used to start or stop plasma purification system. Clean filter indication will be 'ON' on panel,
when filter cleaning is required.
9 SLEEP BUTTON
Sleep function can be set by one hour for a maximum of 7 hours. In the first 30 minutes set
temperature increases by 1°C and in the next 30 minutes temperature increases by another
1°C, this temperature then remains till the timer function is deactivated. This is how the
sleep function behaves. The fan speed will change to low speed(F1).
Operation modes may vary in select models.
Fan speed in two steps Low (F1) / High (F2) in select models.
AUTO RESTART
In failure of electric power the unit runs as prev ious setting oper ation when power returns .
NOTE: ‘SLEEP’ and ‘TIMER’ function cannot operate at same time.
How to Insert the Batteries
1 Remove the cover from the back of the remote
controller.
Slide the cover according to the arrow direction.
2 Insert the two batteries.
Be sure that the (+) and (-) directions are correct.
Be sure that both batteries are new.
3 Re-attach the cover.
Slide it back into the position.
-7-
Do not use rechargeable
batteries, such batteries differ
from standard dry cells in shape,
dimensions, and performance.
Remove the batteries from the
remote controller if the air
conditioner is not going to be
used for an extended length of
time.
REMOTE CONTROLLER
Type 1
Type 2
POWER
Turbo
(e)
Saver
HIGH COOL
27°C
Silent
High
Fan
Low
Fan
Comfort
LOW COOL
24°C
HIGH FAN
21°C
LOW FAN
18°C
Cool
Auto
Swing
Super
Cool
Mode
Temp
2
3
1
4
1
TEMP
3
Auto
Swing
FAN SPEED
4
5
Mode
Temp
ON/OFF
MODE
2
2
3
1
AUTO SWING
4
Controls
Precaution: The Remote Control unit will not function properly if strong light strikes the sensor
window of the air conditioner or if there are obstacles between the Remote Control
unit and the air conditioner.
1
POWER BUTTON
Operation starts, when this button is pressed and stops when you press the button again.
2
MODE
Select (a) Turbo (b) Silent (c) High Fan & (d) Low Fan with this button.
(a) Turbo / High Cool : Switches on compressor and air cooling operation at high fan speed.
(b) Silent / Low Cool : Switches on compressor and air cooling operation at low fan speed.
(c) High Fan : Circulates filtered air at high speed.
(d) Low Fan : Circulates filtered air at low speed.
It is recommended to select 'Silent / Low Cool' for Normal Cooling Operation and select
'Turbo / High Cool' for maximum cooling requirement.
3
TEMP
Controls Room temp. from 18°C to 27°C with step of 3°C.
a) Super Cool / 18°C : 18°C Temperature Setting.
b) Cool / 21°C : 21°C Temperature Setting.
c) Comfort / 24°C : 24°C Temperature Setting.
d) (e) Saver / 27°C : 27°C Temperature Setting.
4
AUTO SWING
The vertical louver swings horizontally by the automatic system and stops when
you press the button again.
5
FAN SPEED
Select fan speed in two steps - High/Low.
-8-
Additional controls and important information.
Vent Control
The vent control is located above the
control knobs.
When set at CLOSE, only the air inside
the room will be circulated and
conditioned. When set at OPEN, some
inside air is exhausted outside.
CLOSE
VENT
OPEN
To open the vent, pull the lever toward you.
To close it, push it in.
Air Direction
The direction of air can be controlled
horizontally or vertically by using the
horizontal louver or vertical louver.
Horizontal Air-Direction
The horizontal air direction is adjusted
by setting the AUTO SWING switch to
the ON position.
Vertical Air-Direction
Fingertip pressure on the bank of horizontal
louvers adjusts the air direction up or down
Parts Information
Learning parts name prior to installation will help you understanding the installation procedure.
1
1. CABINET
2. FRONT GRILLE
3. AIR FILTER
4. AIR INTAKE(INLET GRILLE)
5. AIR DISCHARGE
2
3
4
5
6
15
6. VERTICAL AIR DEFLECTOR
(HORIZONTAL LOUVER)
7. EVAPORATOR
8. HORIZONTAL AIR
DEFLECTOR
(VERTICAL LOUVER)
-9-
7
8
9.
10.
11.
12.
13.
14.
15.
CONTROL BOARD
POWER CORD
COMPRESSOR
BASE PAN
BRACE
CONDENSER
PLASMA FILTER ASSY.
9
10
11 12 13 14
Care and Maintenance
Grille and Case
To clean, use water and a mild detergent. Do not
use bleach or abrasives.
Turn the air conditioner off and remove the plug
from the wall outlet before cleaning.
Air Filter
Ensure the power is off before open the front Grill.
The air filter behind the front grille should be checked and cleaned
at least once every 2 weeks or more often if necessary.
The grille is designed to clean the filter downward.
To remove:
1 Open the inlet grille upward by pulling out the bottom of the
inlet grille. (Refer Fig. 1)
(Fig. 1)
(Fig. 2)
2 Using the tab, pull up slightly on the filter to release it and pull
it down (Fig. 1). Slide out five filter from grill (fig. 2).
3 Clean the filter with warm, soapy water below 40°C (104°/F).
4 Rinse and gently shake the water from the filter and let it dry
before replacing it.
CAUTION: DO NOT operate the air conditioner without a filter
because dirt and lint will clog it and reduce
performance.
Drainage
1 In humid weather, excess water may cause the BASE PAN to overflow.
To drain the water, remove the DRAIN CAP
2 To remove the condensed water, you can install the drain pan as below.
1. Take the drain pan which is located in the air discharge.
2. Install the drain pan to the right corner of the cabinet with 4 screws.
3. Connect the drain hose to the outlet located at the bottom of the drain
pan. You can purchase the drain hose or tubing locally to satisfy your
particular needs. (Drain hose is not supplied).
BASE
PAN
BASE
PAN
DRAIN
CAP
DRAIN CAP
CABINET
DRAIN
PAN
SCREW
DRAIN HOSE
Important
Long-off period maintenance
(Optional)
1)If the air conditioner is not going to be used for a long period, run the Air-conditioner with the
setting in FAN Mode only and the fan speed on "HIGH" for about half an hour, to dry the whole
Air-conditioner.
2)After a long off period when you are going to use the air conditioner again, repeat above point
no. 1.
Caution
There will possibly be foul smell when the machine is started after a long time (1 week). This is due
to various odours emitted by smoke, foodstuff, cosmetics and others, which syicks to the Air Filter
and Evaporator coil. Hence, clean the Air Filter and the Evaporator before you start the machine
after long time to avoid foul smell.
-10-
Installation Instructions
Select the Best Location
A
To prevent vibration and noise, make sure the unit is installed securely and firmly.
B
C
Install the unit where the sunlight does not shine directly on the unit.
D
There should be no obstacle, such as a fence or wall, within 50cm from the back of the cabinet because it will prevent
heat radiation of the condenser.
Restriction of outside air will greatly reduce the cooling efficiency of the air conditioner.
Install the unit a little obliquely outward not to leak the condensed water into the room (about 10 ~ 15mm or 1/4
bubble with level).
CAUTION: All side louvers of the cabinet must remain exposed to the outside of the structure.
Top View
Side View
Wall
Ceiling
Over 100 mm
Over 110 mm
Over 1000 mm
Outdoor
Indoor
Over
200 mm
10mm
AC Top
Room AC
Over
200 mm
Wall
Wall
Indoor
Wall
Position A
Over 1200 mm
Floor
Front View
Side View
Unit Width 'A'
Wooden frame 45~50mm
15mm
Room AC
Unit
Height
'B'
Horizontal
Line
-5 ~ +5mm
Window Width "A"
About 45mm
25mm
Window
Height
"B"
8~10mm
About 400~500mm
Wall
CATEGORY A
12000 Btu/h 600
18000 Btu/h 660
22000 Btu/h 660
B
380
428
428
Remove the Air Conditioner From the Case
A
Remove the 2 shipping screws from the
back of the case.
B
Remove the 2 screws on each side of the
case. Keep these for later use.
C
Shipping screws
-11-
Slide the air conditioner from the case by
gripping the base pan handle and pulling
forward while bracing the case.
Installation Instructions
Install the Air Conditioner in the Case
A
E
Slide the air conditioner into the case.
Reinstall the screws removed earlier on
each side of the case.
Attach the front grille to the case by
inserting the tabs on the grille into the slots
on the front of the case. Push the grille in
until it snaps into place.
Deo-filter*
Screw
Power Cord
Screw
CAUTION: The power cord must be connected to
an independent circuit.
The green wire must be grounded.
B
Stuff the foam between the unit and the
wall to prevent air and insects from getting
into the room.
When you detach the
front grille from the
case, push the grille
to your rightside and
pull it toward you.
The Foam
C
F
Fix Holder lock with base pan & cabinet
with screw to prevent machine from
sliding out of cabinet from back grill side
(Anti theft locking)
Lift the Inlet grill and secure the front grill
with a screw Lower the inlet grill into place.
The maximum lift angle should not be more
than 75°
Max opening angle 75 degree**
D
* Deo-filter available in select Models.
Remove Deodorizing filter carefully from the grill, shake
clean it by hand & keep it in sunlight for one hour to
activate it again; once it is choked.
Before installing the front grille, pull out the
vent control lever located above the unit
control knobs, as shown.
** Grill lifting features available in
selected models
G
-12-
To fix the grill with cabinet, screw it
from both sides
Before you call for service...
Normal Operation
You may hear the thermostat click when the compressor cycles on and off.
Water will collect in the base pan during high numidity or on rainy days. The water may overflow
and drip from the outdoor side of the unit.
The fan may run even when the compressor does not.
Hissing Noise- Sound of liquid refrigerant passing througe the system.
Abnormal Operation
Problem
Possible Causes
What To Do
The air conditioner is
unplugged.
Make sure the air conditioner plug is pushed
completely into the outlet.
The fuse is blown/circuit
breaker is tripped.
Check the house fuse/circuit breaker box and
replace the fuse or reset the breaker.
Power failure.
If power failure occurs, turn the OPERATION control
to OFF( O ) . When power is restored, wait 3 minutes
to restart the air conditioner to prevent tripping of the
compressor overload.
Airflow is restricted.
Make sure there are no curtains, blinds, or furniture
blocking the front of the air conditioner.
THERMOSTAT control set
too warm.
Turn the THERMOSTAT knob clockwise to a cooler
setting.
The air filter is dirty.
Clean the filter at least every 2 weeks.
See the operating instructions section.
The room may have been
hot.
When the air conditioner is first turned on you need
to allow time for the room to cool down.
Cold air is escaping.
Check for open furnace floor registers and cold air
returns.
Set the air conditioner's vent to the closed position.
Cooling coils have iced up.
See Air Conditioner Freezing Up below.
Air conditioner
freezing up
Ice blocks the air flow and
stops the air conditioner
from cooling the room.
Set the OPERATION control at fan or HIGH cool with the
THERMOSTAT at the warmer position or the temperature
at more than 23°C.
AC Operation
is Noisy
Glass pane vibrating.
Glass are to be penned
May be sound of
condensate water.
It is normal (Generally highing only)
(To avoid the noise, remove draing side knob & insert drain pipe
for proper drainge)
Installation levelling not
not proper.
Get it levelled properly.
Compressor not starting
due to 3 minute delay
internally.
This is normal.
If you restart the air conditioner within 3 minutes after turning it
off a protective device will work to shut it off for 3 minutes.
Air conditioner
does not start
Air conditioner
does not cool as it
should
Unit does not
Cool upon
restart
-13-
10 Easy Steps to find out your AC tonnage
Dear Customer,
Please follow Below mentioned 10 easy steps to find out the AC tonnage required for your room.
Step
1
Parameter
Room Volume (Cubic feet)
upto 1000
1001 ~ 2000
2001 ~ 3000
3001 ~ 4000
Score
Step
2
3
4
5
6
Window Area exposed to sun
(in sq. ft.) - (West facing)
2
upto 10
11 ~ 20
21 ~ 30
1
2
3
7
0
1
2
3
8
Window Area exposed to sun
(in sq. ft.) - (other directions)
3
4
5
upto 10
11 ~ 20
21 ~ 35
36 ~ 50
Wall Area exposed to sun
(in sq. ft.) - (West facing)
100
150
200
300
Wall Area exposed to sun
(in sq. ft.) - (other directions)
100
150
300
500
Score
6~10
11~17
18~25
1
2
3
4
9
0
1
2
3
10
Parameter
Walls area - not exposed to
sun (in sq. ft.)
100
300
600
1000
No. of persons occupying
room
2
4
6
8
Ceiling area exposed to sun
(in sq. ft.)
200
300
400
Ceiling area if not exposed to
sun (in sq. ft.)
200
300
400
Total Appliance Load (tube
light-40w / Computer75w, CTV - 75 etc.)
100W
250W
500W
Score
0
1
2
3
1
2
3
4
1
2
3
0
1
2
2
3
4
AC recommended
1.0Tr
1.5Tr
2.0Tr
Score Table
Example : For Room size 15 feet(L) x 12 feet(B) x 10 feet(H) with one window 4 feet x 3 feet exposed to
sun (west) & one wall exposed to sun (east).The room is on First floor with ceiling not exposed to sun.
The no. of persons occupying the room is 4 nos. The appliance load is – 2 tube lights, 1 Computer & 1 TV.
Calculate the AC tonnage required.
As per steps given above : room volume : 15*12*10 = 1800 cu. Ft. , window area = 4*3=12 sq.ft.,
Wall area (east) = 15*10=150
Step1 = 3
Step2 = 2
Step3 = 0
Step4 = 0
Step5 = 1
Step6 = 2
Step7 = 2
Step8 = 0
Step9 = 1
Step10= 3
Total score = 14
-14-
1.5T Window AC
(From Score table)
BRANCH
BRANCH OFFICE ADDRESS
STD CODE PHONE NO.
Ahmedabad
LGEIL, 233-234, Platinum Plaza, Judges Bunglow Road, Bodakdev Road, Ahmedabad - 51
079
50040012/17, 30928467, 30928471
Agra
LGEIL, 1/2, Kendriya Hindi Sansthan, Khandeari Crossing, Agra
0562
2530913, 2530917, 3096036/3956267
Asansol
LGEIL, Block-E, Ist Floor, P C Chattarjee Market, Rambandhu Tala, GT Road (E), Asansol-713303
0341
3096036, 3092009, 3092010
Aurangabad
LGEIL, 302, CIDCO No. 3, Opp. Hotel Ramgiri, Jalna Road, Aurangabad - 431003
0240
2344705, 3095438
Amritsar
LGEIL, Ganda Singh Wala, Majitha Road, Basement of Syndicate Bank, Amritsar, Punjab
0183
5548001/02/03
Bhatinda
LGEIL, Y P O Gursar Sanewala, 12 KM Milestone, Village Mehta Link Road, Bhatinda-151001
0164
2420448, 2229933, 3098274/75
Bangalore
LGEIL, 93,TKN Mansion, Ground Flr, KH Road, Banglore - 560027
080
51145145, 30910754, 30910753
Bhopal
LGEIL, 13A, Vignes Warehousing Corporation, Sector-G, Govindpura Industrial Area, J K Road, Bhopal
0755
5262847, 5262848, 5260717, 3092938, 3959804
Bhubaneshwar
LGEIL, Plot No. 02, 1st Flr., Bapuji Nagar, Bhubaneshwar- 751009
0674
2531430, 2534280, 3966525, 3966526
Calcutta
LGEIL, 1, Ho-Chi-Min-Sarani, 6th Floor, Metro Towers, Calcutta-700071
033
22883250/51, 30946125
Chandigarh
LGEIL, Plot No.177-G, Ind. Area, Phase-1, Chandigarh
0172
5087389,90, 3959595, 3959596
Chennai
LGEIL, AA11, 2nd Avenue, Fatima Tower, Anna Nagar West, Chennai-600040
044
55510500/08, 30924478, 30924479
Cochin
LGEIL, 40/1270, Vasudeva Buildings, T.D. Road, Ernakulam Cochin-682011
0484
2368966, 2370744, 3946877, 3946878
Coimbatore
LGEIL, 250A, Sanganur Main Road, Kannappa Nagar, Coimbatore-641027
Delhi(South & East) LGEIL, 221,Okhla Industrial Area, Phase-III, New Delhi
Delhi(North& West) LGEIL, 13 Milestone, Rohtak Road, Opp. Maharaja Agrsen Hospital, Punjabi Bagh, New Delhi-110026
0422
Dehradun
0135
LGEIL, M - 22, Mobbewala, Tata Commercial Compound, Dehradun-Saharanpur Road, Dehradun
011
011
2332506, 2331862, 3094613, 3094573
26830953, 26837347, 30989665/30989279
9873002340/9873002339
2644213, 2644283, 3093412, 3093411
Goa
LGEIL, Plot No. D-3&D-4, Rego Baug, Alto Santacruz, Bambolim, Goa-403
0832
3094759, 3094955, 3094956
Gurgaon
LGEIL, IInd Flr, A Block, Centre Point Bldg, Sushant Lok, Gurgaon
0124
5047461/62/63, 3950019, 3099959
Ghaziabad
LGEIL, J-10, RDC Rajnagar, Ghaziabad
0120
2722973, 2724686, 3943465, 3943467, 3943465, 3943467
Guwahati
LGEIL, Shantineer Bhawan, C K Aggarwal Path, Chenikurthi, Guwahati-781003
0361
2668984, 2662896, 2663895, 2665983, 2666958
Hyderabad
LGEIL, K/1/1, IDA, Uppal, Hyderabad - 500039
040
27207504/05/06, 30921140
Hubli
LGEIL, 603/1B, Ravi Nagar Road, Behind Renuka Petrol Pump, Gokul Road, Hubli-580030
0836
2337251/52/53, 3090749, 3090651
Indore
LGEIL, 3rd Flr., 304 Bansi Trade Centre, 581/5 M.G. Road, Indore-452003
0731
5065523/24, 2546985, 25065669, 3956060, 3956065
Jaipur
LGEIL, B-71, Sahakar Marg, Lal Kothi Scheme, Jaipur-302015
0141
2741553, 2742639, 3951458, 3951478
Jallandhar
LGEIL, Opp Jassi Market, Village Khajurla, Near TVS Godown, GT Road, Jallandhar
0181
502667/68, 3955644/3955643
Jammu
LGEIL, Plot No.-52,Transport Nagar, Narwal, Jammu
0191
2477420, 2477419, 2474396, 2474384
Jodhpur
LGEIL, 22(1-A), RIICO Heavy Industrial area, Jodhpur - 342003
0291
2742403, 2742384, 3093487(Accounts), 3093489
Jorhat
LGEIL, Jail Road, Milleneum Stores, Jorhat-785001
0376
2309120
Kundli
LGEIL, Sunshine Enterprises, Sunder Cold Storage, GT Karnal Road, Kundli-Sonipat
0130
2219201, 2219202, 2219203, 2219204, 30997371, 30997496
Kozhikode
LGEIL, 11 / 434, Eranhikkal Bldgs, Cherooty Road, Kozhikhode- 673001 (Kerala)
0495
2366755, 2366756, 2366678, 3955567, 3955568
Lucknow
LGEIL, 537, Hari Kunj, Keshav Nagar, Sitapur Road, Lukhnow
0522
2757538/39/58/59, 3951507/8/9
Ludhiana
LGEIL, Village Jhande, Near Badowal Railway Station, Opp Ferozpur Road, Ludhiana
0161
2804412/15, 3959985
Madurai
LGEIL,7-1-54, Jothimal Godown, Madurai Dindigul High Road, Paravai, Madurai-625402 (Tamilnadu)
0452
2464016
Mumbai
LGEIL, Unit No.3, L-Wing, 2nd Flr., Tax Center, Behind HDFC Bank, Chandiwali, Andheri(E), Mumbai-400072
022
28472410/14, 39522108, 39516172
Nagpur
LGEIL, 5A, Road No.13, Behind MSRTC Workshop, MIDC Hinga, Nagpur-440016
07104
235120, 235122, 3092641, 3092642
Patna
LGEIL, Sumitra Sadan, IInd Flr, West Boring Road, Crossing Patna - 800001
0612
'3098714, 3099156
Pune
LGEIL, 105/106, Premium Point, IIIrd Flr, Shivaji Marg, Pune - 411005
020
56030736, 56030732/33/34, 30922960, 30967366, 30915833
Raipur
LGEIL, Nathani Compound, Shyam Nagar, Katora Talab, Raipur(C.G)
0771
5037470, 5053171, 3959707, 3959708
Ranchi
LGEIL, 402, Commerce Tower, Opp. Gel Church Complex, Main Road, Ranchi
0651
2331519, 2331815, 3090426
Rajkot
LGEIL, 301, 302 Dhanrajni, Dr. Yagnik Road, Rajkot - 360001
0281
2481499, 2467692, 3094093, 3094096
Surat
LGEIL, 1001-1004, Ascon Plaza, IInd Flr, Anand, Mahal Road, Behind Bhulka Bhavan School, Adajan, Surat-395009 0261
2730982/85, 3954419
Thane
LGEIL, Gall No. 6-9,S-2, Golden Park Complex, Hardas Nagar, LBS Marg, Panchpakhadi, Thane (West)-400602
277497/277559, 39526264
02522
Tirupati
LGEIL, 19-3-13/M4, Behind Hero Honda Showroom, Renugunta Road, Tirupati - 517501
0877
2282306/08
Udaipur
LGEIL, 101, Moti Magri Scheme, Udaipur
0294
3093426, 3093462
Varanasi
LGEIL, Pama Complex, DLW, Lahartara Road, Shivdaspur, Manduadih, Varanasi (UP)
0542
2373919, 3091773, 1774, 9839800000
Vijaywada
LGEIL, 1st Floor, Yalamanchili Complex, Ring Road, Near Executive Club, Vijay wada - 520008.
0866
2450128, 3094526, 3094528
Email : happycalls@lgezbuy.com
LG Electronics
P/No.: 3828A30140G
Download PDF