LG | LSN6CG2BCAP | LG LSN24PWAS1 Owner’s Manual

Room Air Conditioner
OWNER’S MANUAL
Please read carefully and thoroughly this
manual before operating this unit.
Safety Precautions
Safety Precautions
Warning ................................2
Caution .................................3
Operating Instructions
Preparation before operation.. 4
Remote Control Features....... 5
Operation Mode Selection...... 7
Operating Instructions
Additional Features...............14
Safety precautions
To prevent injury to the user or other people and property damage, the
following instructions must be followed.
Incorrect operation due to ignoring of instruction will cause harm or
damage. the seriousness is classified by the following indications.
WARNING
WARNING
This symbol indicates the possibility of death or serious injury.
CAUTION
CAUTION
This symbol indicates the possibility of injury or damage to
properties only.
Care and Maintenance
Installation precautions
Care and Maintenance..........17
Operation Tips.......................19
Troubleshooting tips
Before You
Call For Service................ 20
WARNING
Do not install, remove and reinstall the unit by yourself.
• Improper installation will cause water leakage, electrical
shock, or fire. Please consult authorized dealer or specialist
for the installation work. Please note fault caused by
improper installation is not covered by warranty.
• Unit must be installed in an easily accessible area. Any
additional cost required to hire a special equipment to
service the unit will be the responsibility of the customer.
Troubleshooting Tips
Care and Maintenance
WARNING
Plug in the power plug
properly.
• Otherwise, it will cause
electrical shock or fire due to
heat generation.
Do not operate or stop the
unit by inserting or pulling
out the power plug.
• It will cause electrical shock
or fire due to heat
generation.
Do not modify power cord
length or share the outlet
with other appliances.
Do not operate with wet
hand.
• It will cause electrical shock
or fire due to heat
generation.
• It may cause electrical
shock.
Do not expose the skin
directly to cool air for long
perlods of time.
• This could damage your
health.
Do not damage or use an
unspecified power cord.
• It will cause electrical shock or fire.
• If the supply cord is damaged, it
must be replaced by the
manufacturer or its service agent
or a similarly qualified person in
order to avoid a hazard.
Do not insert anything into the
air Inlet/air outlet.
• Since the fan rotates at high
speed, this may cause an
injury or damage the unit.
When an abnormality (smell of burning, etc)
occurs, stop the air conditioner, and disconnect
the power plug or turn off the breaker.
Repair or relocation should
not be done by the
customer.
• If the unit continues to be operated
in an abnormal condition, it may
cause a fire, damage, etc. In this
case, consult your dealer.
• If this is done incorrectly, it may
cause a fire, electric shock, injury
by dropping of the unit, water
leakage, etc. Consult your dealer.
2
• Contact the authorized Service technician for repair or maintenance of this unit.
• Contact the installer for installation of this unit.
• The air conditioner is not intended for use by young children or infirm persons
without supervision.
• Young children should be supervised to ensure that they do not play with the air
conditioner.
Safety Precautions
CAUTION
CAUTION
• It may cause an injury.
• Should be disconnected from
supply
When the unit is to be
cleaned, switch off, and turn
off the circuit breaker.
• Since the fan rotates at high
speed during operation, it
may cause an injury.
• It may cause a fire or
deformation of the cabinet.
Do not insert hands through
vanes when the air conditioner
is operationg
• It will cause an injury by the
rotating blower.
• Do not use this air conditioner
to preserve precision devices,
food, animal, plants, and art
objects.
It may cause deterioration of
quality, etc.
Do not put a pet or house
plant where it will be
exposed to direct air flow.
• An oxygen shortage may
occur.
Do not leave on installation
stand which is damaged.
• This could injure the pet or
plant.
• The unit may drop or fall
down and cause an injury.
Do not put a stove, etc.
where is exposed to direct
air flow.
• It may affect combustion.
Do not step on the
indoor/outdoor unit and do
not put anything on it.
• It may cause an injury
through dropping or falling
down.
When the unit is not going to
be used for a long time, turn
off the circuit breaker.
• If not, dirt may collect and
cause a fire.
Do not operate for a long time in
high humidity, e.g. leaving a
door or window open.
• In the cooling mode, if it is
operated in a room with high
humidity (80% RH or more) for
a long time, water condensed
in the air conditioner may drop
and may wet and spoil
furniture, etc.
3
Do not step onto an unstable
bench when cleaning and/or
maintaining the unit.
• It may cause an injury, etc.
by falling down.
Troubleshooting Tips
Do not use for special
purposes.
• Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
Ventilate well when used
together with a stove, etc.
Care and Maintenance
Do not apply an insecticide
or flammable spray.
Do not clean the air
conditioner with water.
Operating Instructions
When the air filter is to be
removed, do not touch the
metal parts of the indoor unit.
Troubleshooting Tips
Care and Maintenance
Operating Instructions
Safety Precautions
Preparation before operation
How to Insert the Batteries
Remove the battery cover by pulling it according to the
arrow direction.
Insert new batteries making sure that the (+) and (-) of
battery are installed correctly.
Reattach the cover by sliding it back into position.
NOTES:
• Use 2 AAA(1.5volt) batteries. Do not use rechargeable
batteries.
Storage and Tips For Using the Remote Control
• The remote control may be stored by mounting it
on a wall.
• To operate the room air conditioner, aim the
remote control at the signal receptor.
Signal Receptor
Receives the signals from the remote control.(Signal receiving sound: two short beeps or one long beep.)
Operation Indication Lamps
On/Off
: Lights up during the system operation.
Sleep Mode
: Lights up during Sleep Mode Auto operation.
Timer
: Lights up during Timer operation.
/ Defrost
Defrost Mode
: Lights up during Defrost Mode or Hot
Start operation (Heat pump model only)
OUT
DOOR
OUTDOOR UNIT : Lights up during outdoor unit operation.
OPERATION
(Cooling model only)
4
Signal
receptor
Operation indication lamps
The remote control transmits the signals to the system.
Features of the Remote Control- Door Closed
Signal transmitter
Signal transmitter
6
5
FAN SPEED
4
1
1
POWER
4
3
3
4
3
2
TYPE A
1
FAN SPEED
2
2
POWER
TEMP
1
MODE
A/SWING
OL
JET CO
3
4
Flip-up door
(closed)
5
6
Signal transmitter
2
ON
Flip-up door
(closed)
TYPE B
MODE
ON
Flip-up door
(closed)
TYPE C
Flip-up door
(closed)
TYPE D
Used to select fan speed in four steps
low, medium, high, or CHAOS.
pressed and stops when the button is
pressed again.
OPERATION MODE
2 SELECTION
BUTTON
JET COOL
5 Used
to start or stop the speed
ROOM TEMPERATURE
3 SETTING
BUTTONS
6
Used to select the operation mode.
cooling. (Speed cooling operates
super high fan speed in cooling mode).
Used to select the room temperature.
AIR SWING BUTTON
Used to stop or start louver movement and
set the desired up/down airflow direction.
Cooling Operation
Cooling Operation
Auto Operation
Auto Operation
Healthy Dehumidification Operation
Healthy Dehumidification Operation
Heating Operation
(Cooling Model)
(Heat Pump Model)
* Your unit shall have either Type A,Type B, Type C or Type D Remote Control
5
Troubleshooting Tips
Operation Mode
Care and Maintenance
INDOOR FAN SPEED
4 SELECTOR
START/STOP BUTTON
1 Operation
starts when this button is
Operating Instructions
5
6
JET COOL TEMP A/SWING
6
5
Signal transmitter
Safety Precautions
About the remote control on the system
Safety Precautions
Features of the Remote Control- Door Opened
Signal
transmitter
ON/OFF TIMER BUTTONS
1 Used
to set the time of starting and stopping
operation.
Troubleshooting Tips
Care and Maintenance
Operating Instructions
Signal
transmitter
TIME SETTING BUTTONS
2 Used
to adjust the time, (See page 15)
TIMER SET/CANCEL BUTTONS
3 Used
to set the timer when the desired time is
1
ON
OFF
SET
CANCEL
obtained and to cancel the Timer operation.
(See page 15)
4
5
2
3
JET COOL TEMP
6
PLASMA
FAN SPEED
7
8
A/SWING
POWER
SLEEP MODE AUTO BUTTON
4 Used
to set Sleep Mode Auto operation.
9
ON TIMER OFF
1
SLEEP
SET
3
CANCEL
MODE
4
FAN
TIMER
2
AIRFLOW
(See page 15)
5
ROOM
6
PLASMA
7
AIR CIRCULATION BUTTON
5 Used
to circulate the room air without cooling
RESET
8
9
or heating. (See page 16)
Signal
transmitter
ROOM TEMPERATURE
6 CHECKING BUTTON
Used to check the room temperature.
Signal
transmitter
7
4
HORIZONTAL AIRFLOW
CANCEL
1
5
2
7
3
ON
OFF
A/SWING
OL
JET CO
SET
6
8 DIRECTION CONTROL BUTTON
POWER
TEMP
(OPTIONAL)
8
9
Used to set the desired horizontal airflow
direction. (See page 16)
FAN SPEED
10
4
MODE
Flip-up door
(opened)
PLASMA (OPTIONAL)
Used to start or stop the plasma-purification
function. (See page 13)
1
5
2
7
SLEEP
ON TIMER OFF
FAN
ROOM
CANCEL
SET
TIMER
AIRFLOW
9
3
6
9
8
10
RESET BUTTON
Used prior to resetting time or after replacing
batteries.
2nd F Button (Type C or Type D
10 Remote Control)
Flip-up door
(opened)
Used prior to using modes printed in blue at
the bottom of buttons. (See page 14)
6
Cooling Operation
Press the Start/Stop button.
The unit will respond with
a beep.
2
Open the door on the remote control. To select Cooling
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the arrow.
POWER
MODE
Cooling
JET COOL
FAN SPEED
TEMP
Healthy
Dehumidification
Heating
(Heat pump model only)
Close the door on the remote control. Set the temperature
higher than the room temperature. The temperature can be
set within a range of 18°C~30°C in 1°C increments.
A/SWING
To raise the temperature
POWER
To lower the temperature
MODE
4
FAN SPEED
Natural wind by the CHAOS logic
For more fresh feeling than other fan speed, press the Indoor Fan Speed Selector and set to
CHAOS mode. In this mode, the wind blows like natural breeze by automatically changing fan
speed according to the CHAOS logic.
7
Troubleshooting Tips
Set the fan speed again with the door
of the remote control still closed. You
can select the fan speed in four stepslow, medium, high or CHAOS. Each
time the button is pressed, the fan
speed mode is shifted.
Care and Maintenance
3
Auto
Operating Instructions
1
Safety Precautions
How to use the Operation Mode Selection button
Safety Precautions
Care and Maintenance
Operating Instructions
Auto Operation
1
Press the Start/Stop button.
The unit will respond with
a beep.
2
Open the door on the remote control. To select Auto
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the arrow.
POWER
MODE
Cooling
JET COOL
FAN SPEED
TEMP
A/SWING
POWER
3
Auto
Healthy
Heating
Dehumidification (Heat pump model only)
The temperature and fan speed are automatically set by the
electronic controls based on the actual room temperature. If
you want to change the set temperature, close the door on
the remote control and press the Room Temperature Setting
buttons. The cooler or warmer you feel, the more times (up to
two times) you should press the button. The set temperature
will be changed automatically.
MODE
To raise the temperature
Troubleshooting Tips
To lower the temperature
During Auto Operation:
You cannot switch the indoor fan speed. It has already been set by the Fuzzy rule.
If the system is not operating as desired, manually switch to another mode. The system will not
automatically switch from the cooling mode to the heating mode, or from heating mode to cooling
mode, it must be done by manually resetting.
During Auto Operation, pressing the chaos swing button makes the horizontal louvers swing up and
down automatically. If you want to stop auto-swing, press the chaos swing button again.
8
Safety Precautions
Healthy Dehumidification Operation
Press the Start/Stop button.
The unit will respond with
a beep.
2
Open the door on the remote control. To select Healthy
Dehumidification Operation, press the Operation Mode
Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the arrow.
POWER
MODE
Cooling
JET COOL
FAN SPEED
MODE
TEMP
A/SWING
POWER
Healthy
Heating
Dehumidification (Heat pump model only)
Set the fan speed again with the door
of the remote control still closed. You
can select the fan speed in four stepslow, medium, high, or CHAOS. Each
time the button is pressed, the fan
speed mode is shifted.
FAN SPEED
Natural wind by the CHAOS logic
For more fresh feeling than other fan speed, press the Indoor Fan
Speed Selector and set to CHAOS mode. In this mode, the wind
blows like natural breeze by automatically changing fan speed
according to the CHAOS logic.
If you select the dehumidification mode on the operation selection button, the A/C starts to run the
dehumidification function. It automatically sets the room temp. and airflow volume to the best condition
for dehumidification, based on the sensed current room temp.
In this case, however, the setting temp. is not displayed in the remote control and you are not able to
control the room temp. either.
During the healthy dehumidification function, the airflow volume is automatically set according to the
optimization algorithm responding to the current room temp. status which makes the room condition
healthy and comfortable even in the high humidity season.
9
Troubleshooting Tips
During Healthy Dehumidification Operation:
Care and Maintenance
3
Auto
Operating Instructions
1
Safety Precautions
Troubleshooting Tips
Care and Maintenance
Operating Instructions
Heating Operation(Heat pump model only)
1
Press the Start/Stop button.
The unit will respond with
a beep.
2
Open the door on the remote control. To select Heating
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the arrow.
POWER
MODE
Cooling
3
JET COOL
TEMP
Auto
Healthy
Heating
Dehumidification (Heat pump model only)
Close the door on the remote control.
Set the temperature higher than the room temperature.
The temperature can be set within a range of 16°C~30°C in
1°C increments.
A/SWING
To raise the temperature
FAN SPEED
POWER
To lower the temperature
MODE
4
Set the fan speed again with the door of the
remote control still closed. You can select
the fan speed in four steps–low, medium,
high or CHAOS. Each time the button is
pressed, the fan speed mode is shifted.
FAN SPEED
Natural wind by the CHAOS logic
For more fresh feeling than other fan speed, press the Indoor Fan Speed Selector and set to
CHAOS mode. In this mode, the wind blows like natural breeze by automatically changing fan
speed according to the CHAOS logic.
10
Safety Precautions
Jet Cool Operation
A/SWING
2
Press the Jet Cool button to operate
the speed cooling mode and the unit
will operate in super high fan speed
on cooling mode for 30 minutes.
3
To cancel the Jet Cool mode, press the Jet Cool button
again or the fan speed button or the room temperature
setting button and the unit will operate in high fan speed on
cooling mode.
POWER
JET COOL
POWER
TEMP
FAN SPEED
JET COOL
or
or
During the JET COOL function at any moment, the A/C starts to blow the cool air at
extremely high speed for 30 minutes setting the room temp. automatically to 18°C. It is
especially used to cool the room temp. in the shortest time in a hot summer.
In heat pump mode or neuro fuzzy mode, however, the JET COOL function is not available.
In order to return to the normal cooling mode from the JET COOL mode, you just press
either the operation mode selection button, airflow volume selection or temp. setting button
or the JET COOL button again.
11
Troubleshooting Tips
NOTE:
Care and Maintenance
TEMP
Press the Start/Stop button.
The unit will respond with
a beep.
Operating Instructions
JET COOL
FAN SPEED
1
Safety Precautions
Troubleshooting Tips
Care and Maintenance
Operating Instructions
PLASMA Purification Operation(Optional)
1
Press the Start/Stop button.
The unit will respond with a
beep.
2
Open the door on the remote control.
Press the PLASMA air purifying
operation ON/OFF button.
Operation will start when the button is
pressed and stop when the button is
pressed again.
3
JET COOL
FAN SPEED
TEMP
A/SWING
POWER
POWER
PLASMA
Set the fan speed again with door of the remote control
closed. You can select the fan speed in four steps-low,
FAN SPEED
medium, high or CHAOS. Each time the
button is pressed, the fan speed mode
is shifted.
Air purifying operation (PLASMA) can be with cooling,
Heating or any other operations.
PLASMA Air Purifying Operation only
If you press the only PLASMA button, PLASMA
air purifying operates only.
Then, fan speed is low. You can select the fan
speed in four steps-low, medium, high or
CHAOS.
Each time the button (
) is pressed, the fan
speed mode is shifed.
PLASMA
12
Safety Precautions
2nd F Operation
nd
2nd
F
ON
OFF
Press the Start/Stop button.
The unit will respond with
a beep.
2
Open the door of the remote control and press the 2nd
Function button to operate functions printed in blue at bottom
of buttons.
(Check the indication of 2nd function on remote control
display.)
These buttons operate the timer setting as follows:
SET
CANCEL
2ndF
ON
OFF
SET
POWER
MODE
SLEEP
ON TIMER OFF
FAN
ROOM
CANCEL
SET
A/SWING
OL
JET CO
POWER
TEMP
3
2nd function goes off in a short time automatically or when
the button is pressed again.
FAN SPEED
MODE
SLEEP
ON TIMER OFF
FAN
ROOM
CANCEL
SET
TIMER
AIRFLOW
Care and Maintenance
TIMER
Operating Instructions
CANCEL
1
Troubleshooting Tips
13
Operating Instructions
Safety Precautions
Additional features
Sleep Mode
1
Press the Sleep Mode Auto button to set the SLEEP
time you want the unit to turn off automatically.
To cancel the Sleep Mode, press the sleep
Mode Auto button several times until the star
(
) disappears from the operation display.
2
The Timer is programmed in one-hour
increments by pressing the Sleep Mode Auto
button 1 to 7 times.
The sleep mode is available for 1 to 7 times. To
alter the time period in steps of 1 hour, press
the Sleep Mode Button while aiming at air
conditioner.
Note: 1. The Sleep Mode will be operated at
slow fan speed (cooling) or medium
fan speed (heat pump only) for quiet
sleeping.
2. Remote Control will display Fan Speed.
Set before sleep mode although Unit
Fan Speed changes.
3
Make sure the Sleep Mode Auto LED lights up.
Setting the Time
1
Time can be set only when you have pressed
the Reset button. If you have just replaced the
batteries, the Reset button should be pressed
to reset the time.
Care and Maintenance
Press the Start/Stop button.
Troubleshooting Tips
IN COOLING MODE : The temperature will
automatically rise by 1°C over the next 30
minutes and by 2°C in 1 hour for comfortable
sleeping.
POWER
2
Press the Time Setting buttons until the
desired time is set.
TIMER
3
Press the Timer SET button.
SET
Note: Check the indicator
for A.M. and P.M.
Delay Start/Pre-Set Stop
1
Make sure the time is set correctly on the
remote control display.
2
Press the ON/OFF Timer
buttons to turn Timer on or off.
3
Press the Time Setting
buttons until the desired
time is set.
4
ON TIMER OFF
Press the selected on/off setting by
pressing the Timer SET button while
aiming the remote control at the signal
receptor.
SET
To cancel the timer setting
Press the Timer Cancel button while
CANCEL
aiming remote control at the signal
receptor.
(The timer lamp on the air conditioner and
the display will go out.)
TIMER
NOTE: Select one of the following four types of operation.
with the unit running
Delay OFF Timer
Delay ON Timer
Delay OFF and ON Timer Delay ON and OFF Timer
14
The up/down airflow (Vertical Airflow) can be
adjusted by using the remote control.
Press the Start/Stop button to start the unit.
2
Press Air Swing button and the louvers will
swing up and down. Press the Air Swing
button again to set the vertical louver at the
desired airflow direction.
A/SWING
Adjust the left/right airflow direction by hand.
Operating Instructions
1
Note:
If you press the AIR swing button, the horizontal
airflow direction is changed automatically based on the
CHAOS algorithm to distribute the air in the room
evenly and at the same time to make the human body
feel most comfortable, as if enjoying a natural breeze.
Always use the remote control to adjust the up/down
airflow direction. Manually moving the vertical airflow
direction louver by hand, could damage the airconditioner.
When the unit is shut off, the up/down airflow direction
louver will close the air outlet vent of the system.
To adjust left/right(Horizontal Airflow) direction
Caution : Ensure that the unit is turned
off before adjusting the
horizontal airflow direction
control. Carefully open vertical
louver to allow access to the
horizontal airflow direction.
Safety Precautions
Vertical Airflow Direction Control
Horizontal Airflow Direction Control (Option)
Open the door on the remote control. Press the Airflow Direction
Start/Stop button and the louvers will swing left and right. Press
the Horizontal Airflow Direction Control Button again to set the
horizontal louver at the desired airflow direction.
AIRFLOW
Air Circulation Mode
Circulates the room air without cooling or heating.
Press the Start/Stop button. the unit will respond with a beep.
2
Open the door on the remote control. Press the Fan button. Close the door on the
remote control. Now each time that you press the Indoor Fan Speed Selector, the fan speed is
shifted from low to CHAOS and back to low again.
FAN
CHAOS Air
Fan speed is on low.
Fan speed is on medium.
Fan speed is on high.
Note:
CHAOS Air economizes power consumption and prevents overcooling. The fan speed is automatically changed
from high to low or vice versa, depending on the ambient temperature.
15
Troubleshooting Tips
1
Care and Maintenance
The left/right(Horizontal Airflow) can be adjusted by using the remote control.
Press the Start/Stop button to start the unit.
Safety Precautions
Forced Operation
Please follow the step 1 to step 5
for forced operation.
1.
2.
3.
4.
5.
Turn ON the unit using power button.
Turn OFF the unit using power button.
Switch OFF the mains supply to the unit.
Switch ON the mains supply to the unit.
Turn ON the unit using the power button.
Cooling Model
Operating Instructions
Power
button
After turning ON the unit will operate
according to the table below :
Operating mode
Indoor FAN Speed
Setting Temperature
Open the front
panel upward
Heat pump Model
Cooling
High
Room Temp. 24°C
Cooling
High
22°C
22°C
Room Temp. < 21°C
Heating
High
21°C Room Temp. < 24°C
Healthy Dehumidification
High
23°C
24°C
If you want to stop the unit, re-press the power button.
During forced operation there will be no auto restart.
Test operation
During the TEST OPERATION, the unit operates in cooling mode at high speed fan, regardless of
room temperature and the unit will turn off after 18 minutes.
During test operation, if remote controller signal is received, the unit operates as remote controller
sets. If you want to use this operation, open the front panel upward and Press the power button let
it be pressed for about 3 seconds.
If you want to stop the operation, re-press the button.
Care and Maintenance
Auto restart
In case the power comes on again after a power failure, Auto Restarting Operation is the function to
operate procedures automatically to the previous operating conditions.
In the initial mode, the fan operates at a low speed and the compressor starts 2.5~3 minutes later.
As the compressor starts, the fan speed also resumes its previous setting mode.
Note : To Enable/Disable Auto restart function
1. Press ON/OFF (Power) button, located on side of the unit, continuously.
2. After 3 seconds, Buzzer will beep once, then after 3 seconds Buzzer will beep twice.
3. Release the ON/OFF (Power) button.
4. You can see the ON/OFF LED blinking.
* If, LED is blinking, as shown in Pattern A, then auto restart function is enabled.
* If, LED is blinking, as shown in Pattern B, then auto restart function is disabled.
ON
ON
Troubleshooting Tips
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Pattern A
Note:
1)
2)
3)
4)
5)
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
Pattern B
Auto restart can/ can not be operated in the following cases :
Power failure and recovery occur very fast
Earthing is not proper
Power supply fluctuations.
Frequency Variations
Installation of site wiring
Helpful information
Fan speed and cooling capacity.
The cooling capacity indicated in the specification is the value when
the fan speed is set to high, and the capacity will be lower at low or
medium fan speed.
High fan speed is recommended when you wish to cool the room quickly.
16
h
Hig ed
e
Sp
CAUTION:Before performing any maintenance, turn off the main power to the system.
Indoor Unit
Turn the system off before cleaning. To
clean, wipe with a soft, dry cloth. Do not
use bleach or abrasives.
NOTE:
Supply power must be disconnected before
cleaning the indoor unit.
Pow
d er
G a s o li n e
1
AIR FILTERS
the filter with a vacuum or warm, soapy
2 Clean
water.
• If dirt is conspicuous, wash with a
solution of detergent in lukewarm water.
• If hot water (40°C or more) is used, it
may be deformed.
3 After washing with water, dry well in the
shade.
4 Re-install the air filter.
PLASMA FILTER, DEODORIZER
FILTER(OPTIONAL)
1 After removing the air filters, pull slightly
The PLASMA filter behind the air filters should be
checked and cleaned once in every 3 months or
more often if necessary.
2 Dip the PLASMA filter into the water mixed
forward to remove the PLASMA filter.
with neutral detergent, for 20~30 minutes.
Care and Maintenance
The air filters behind the
front grille should be
checked and cleaned
once in every 2 weeks or
more often if neccessary.
Lift the front access panel and pull the filter tab
slightly forward to remove the filter.
Operating Instructions
Never use any of the followings:
• Water hotter than 40°C
Could cause deformation and/or
discoloration.
• Volatile substances
Could damage the surfaces of the air
conditioner.
Grille, Case, and Remote Control
Safety Precautions
Care and maintenance of the air conditioner
3 Dry the PLASMA filter in the shade for a day
4 Note the cuts of electric discharge lines.
5 Re-install the PLASMA filter to the original
position.
After removing the air filters, pull slightly
Don’t touch this PLASMA Filter within 10
seconds after opening the inlet grille, it may
cause an electric shock.
1 forward to remove the DEODORIZER filter.
2 Dry in the sunlight for two hours.
Re-install the DEODORIZER filter to the
3 original position.
17
Troubleshooting Tips
(Especially, the humidity must be removed
perfectly on this parts).
Safety Precautions
Operating Instructions
Care and Maintenance
Troubleshooting Tips
Replacement of Purifying Filter(Option)
• Recomended use period : About 2 years
2 Remove air purifying filters.
1 Open front panel and remove air
filters.
3 Insert new air purifying filters.
4 Reinsert air filters and close front
panel.
Air purifying filter
Outdoor Unit
The heat exchanger coils and panel vents of the
outdoor unit should be checked regularly. If clogged
with dirt or soot, the heat exchanger and panel Air intake (Side)
vents may be professionally steam cleaned.
vents
(Rear)
Piping
Drain Hose
NOTE:
Dirty or clogged coils will reduce the
operating efficiency of the system and cause
higher operating costs.
Air outlet
vents
For drain of water provision has been provided in
outdoor unit. Connect a drain pipe for proper drainage.
18
When air conditioner is not going to be
used for a long time.
When the air conditioner is to be used again.
Clean the air filter and install it in the indoor
unit.
(Refer to page 16 for cleaning filters.)
Operate the air conditioner on Air circulation
mode (Refer to page 14) for 2 to 3 hours.
Safety Precautions
When the air conditioner is not going to be used for a long time.
• This will dry out the internal mechanisms.
Check that the air inlet and outlet of the
indoor/outdoor unit are not blocked.
CAUTION
Turn off the circuit breaker when the air conditioner
is not going to be used for a long time.
Dirt may collect and may cause a fire.
Remove the batteries from the remote
control.
Keep blinds or curtains
closed.
Keep the room temperature
uniform.
This is not good for the health
and wastes electricity.
Do not let direct sunshine enter
the room when the air
conditioner is in operation.
Adjust the vertical and
horizontal airflow direction to
ensure a uniform temperature
in the room.
Make sure that the doors
and windows are shut tight.
Clean the air filter regularly.
Ventilate the room
occasionally.
Avoid opening doors and
windows as much as possible
to keep the cool air in the room.
Blockages in the air filter
reduces the airflow and lowers
the cooling and dehumidifying
effects. Clean at least once in
every two weeks.
Since windows are kept closed,
it is a good idea to open them
and ventilate the room now and
then.
19
Troubleshooting Tips
Do not overcool the room.
Care and Maintenance
Operation Tips
Operating Instructions
Turn off the circuit breaker, and disconnect
the plug.
Safety Precautions
Before you call for service...
?
Troubleshooting Tips! Save time and money!
Check the following points before requesting repairs or service.... If the fault persists, please
contact your dealer or service center.
Case
Operating Instructions
Care and Maintenance
See page
• Have you made a mistake in timer operation?
14
• Has the fuse blown or has the circuit breaker
been tripped?
-
The room has a peculiar
odor.
• Check that this is not a damp smell exuded by
the walls, carpet, furniture, or cloth items in the
room.
-
It seems that condensation
is leaking from the air
conditioner.
• Condensation occurs when the airflow from
the air conditioner cools the warm room air.
Air conditioner does not
operate for about 3 minutes
when restarted.
• This is the protector of the mechanism.
• Wait about three minutes and operation will
begin.
Does not cool or heat
effectively.
• Is the air filter dirty? See air filter cleaning
instructions.
• Has the temperature been set incorrectly?
The air conditioner does not
operate.
Troubleshooting Tips
Explanation
• Are the indoor unit's air inlet or outlet vents
obstructed?
The air conditioner
operation is noisy.
• For a noise that sounds like water flowing.
-This is the sound of freon flowing inside the
air conditioner unit.
• For a noise that sounds like the compressed
air releasing into atmosphere.
-This is the sound of the dehumidifying water
being processed inside the air conditioning
unit.
-
-
17
7, 10
-
-
Remote control display is
faint, or no display at all.
• Are the batteries depleted?
• Are the batteries inserted in the opposite (+)
and (-) directions?
4
Crack sound is heard.
• This sound is generated by the
expansion/constriction of the front panel, etc.
due to changes of temperature.
-
NOTE
WATER RESISTANT: The outdoor side of this appliance is WATER RESISTANT.
The indoor side is not water resistant and should not be exposed to excess water.
20
P/No.: MFL37725116
Download PDF