LG | LSN3EW3Z | LG LSN3EW3Z Owner’s Manual

OWNER’S MANUAL
AIR CONDITIONER
Please read this manual carefully before operating
your set and retain it for future reference.
TYPE : WALL MOUNTED
LG Electronics India Pvt. Ltd.
P/No. MFL39754854
Registered Office : A-27, Mohan Co-operative
Industrial Estate, Mathura Road, New Delhi-110044
Tel: 011-26991412, Fax: 011-26991410
www.lg.com
(Recommended 24°C is suitable for human body)
(Refer page no. 20 and 21 for details)
15 ADVANCED FUNCTIONS
– Product Introduction
– Electrical Safety
– Using the remote control
Inserting Batteries
Installing the remote control holder
Wireless Remote Control
Changing room temperature quickly
Air purification mode
Indoor air purification
– Auto Clean operation
– Plasmaster Purification operation
Auto operation
Quiet Mode (optional)
Energy Saving cooling mode
Dimmer
Operating the air conditioner without the
remote control
Restarting the air conditioner
automatically
20 MAINTENANCE
12 BASIC FUNCTIONS
Cooling your room
Heating your room
Removing humidity
Airing your room
Adjusting the fan speed
Adjusting the air flow direction
Setting the timer
– Setting the current time
– Turning on the air conditioner
automatically at a set time
– Turning off the air conditioner
automatically at a set time
– Cancelling the timer setting
Setting sleep mode
– Cleaning the air filter
– Cleaning the anti-allergy filter
and triple filter
– Cleaning the plasma filter
22 TROUBLESHOOTING
– Self-diagnosis function
– Before requesting service
PRECAUTION
• Contact the authorized service technician for repair or
maintenance of this unit.
• Please install your air-conditioner by company
authorised service franchisee / authorised service
and sales dealer.
• The air conditioner is not intended for use by young
children or invalids without supervision.
• Young children should be supervised to ensure that
they do not play with the air conditioner.
• When the power cord is to be replaced, replacement
work shall be performed by authorized personnel only,
using only genuine replacement parts.
We recommend usage of voltage stabilizer with
high / low voltage cut off in areas having voltage
fluctuations.
AC TONNAGE
STABILIZER KVA
(3-STEP STABILIZER)
1.0
1.5
2.0
3
4
5
BEFORE USE
Production Introduction
Indoor Unit
The number of operation lamps and their locations may vary, depending on the model of the
air conditioner
Outdoor Unit
Electrical Safety
Warning
This appliance must be properly grounded.
To minimize the risk of electric shock, you must always plug into a grounded outlet.
Do not cut or remove the grounding prong from the power plug.
Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance
unless the cover screw is metal and not insulated, and the wall receptacle is grounded through the
house wiring.
If you have any doubt whether the air conditioner is properly grounded, have the wall receptacle and
circuit checked by a qualified electrician.
Temporary Use of an Adapter
We strongly discourage the use of an adapter due to potential safety hazards. For temporary connections,
use only a genuine adapter, available from most local hardware stores. Ensure that the large slot in the
adapter is aligned with the large slot in the receptacle for a proper polarity connection.
To disconnect the power cord from the adapter, use one hand on each to avoid damaging the ground
terminal. Avoid frequently unplugging the power cord as this can lead to eventual ground terminal damage.
Warning
Never use the appliance with a broken adapter.
Temporary Use of an Extended Cord
We strongly discourage the use of an extension cord due to potential safety hazards.
Warning
This appliance should be installed in accordance with national wiring regulations. This manual acts as a
guide to explaining product features.
Symbols used in this Manual
This symbol alerts you to the risk of electric sock.
This symbol alerts you to hazards that may cause harm to the
air conditioner
This symbol indicates special notes
Using the remote control
Using the remote control
You can operate the air conditioner more conveniently with the remote control. You will find the
buttons for the additional functions under the cover of the remote control.
Wireless remote control
Control panel Display Screen
Description
ON/OFF BUTTON
Turns the power on/off.
POWER
OPERATION MODE SELECTION BUTTON
MODE
.
Display
Screen
PLASMA
JE T C
PLASMA
OOL
POWER
Air Circulation (
FAN
TEMP
ROOM TEMPERATURE SETTING BUTTONS
Used to select the room temperature.
FAN SPEED
INDOOR FAN SPEED SELECTION BUTTON
Used to select fan speed in four stops - Low,
Medium, High and natural wind.
TEMP
HORIZONTAL VANE CONTROL BUTTON
Used to set the desired vertical airflow direction.
Control
Panel
VERTICAL LOUVER CONTROL BUTTON
Used to set the desired horizontal airflow direction.
FAN SPEED
SLEEP
MODE
).
CANCEL
SET
ON–TIMER–OFF
FAN
ROOM
AUTO CLEAN
AUTO CLEAN BUTTON
Used to set auto clean.
AUTO CLEAN
ROOM TEMPERATURE CHECKING BUTTON
Used to check the room temperature.
ROOM
–TIMER–
ON/OFF TIMER BUTTONS
Used to set the time of starting and stopping operation.
ON–TIMER–OFF
STEP
TIME SETTING BUTTONS
Used to adjust the time.
–TIMER–
CANCEL
TIMER SET/CANCEL BUTTON
Used to set and to cancel the timer operation.
SET
RESET BUTTON
Used prior to resetting time.
RESET
PLASMA
PLASMA
PLASMA BUTTON (Optional)
Used to start or stops the PLASMASTER-purification.
DIMMER (Optional)
Used to operate Dimmer Function using 2ndF.
SLEEP MODE AUTO BUTTON
Used to set sleep mode auto operation.
SLEEP
JET COOL BUTTON
Used to start or stop the speed cooling. The Jet Cool
operates fan in super high speed in cooling mode.
JET COOL
2ndF BUTTON
Used prior to using modes printed in blue at the
bottom of buttons.
22
QUIET
ENERGY SAVER MODE
Used to operate Energy Saver function.
QUIET MODE (Optional)
Used to operate Quiet Mode function.
* Some functions may not be supported, depending on the model
12
BASIC FUNCTIONS
Cooling your room
POWER
MODE
Following is the display on the display
screen.
POWER
MODE
(Heating operation / Heat Pump model only)
POWER
MODE
Following is the display on the display
screen.
The temperature range is 180C-300C.
In this mode indoor unit fan and outdoor
unit will be OFF when set temperature is
achieved.
13
Selectable Air Swing (Horizontal)
(Optional)
POWER
FAN
to select the air circulatiion
operation.
Following will be displayed on the display
screen.
To adjust the direction of the air flow horizontally.
Open the remote control cover while the
air conditioner is in operation.
Press the 2ndF Button.
Press the HORIZONTAL VANE
CONTROL BUTTON.
Each time the button is pressed, the air flow
direction is changed in the direction of the
arrow.
1 Step
2 Step
3 Step
4 Step
5 Step
6 Step
Automatic Air Swing (Horizontal)
To adjust the direction of the air flow
automatically, switch OFF 2ndF button
and press
button.
FAN SPEED
Press FAN SPEED repeatedly to adjust
the fan speed.
Select
if you want natural air.
The fan speed adjusts automatically.
Selectable Air Swing (Vertical)
(Optional)
To adjust the direction of the air flow vertically.
Open the remote control cover while the
air conditioner is in operation.
Press the 2ndF Button.
Press the VERTICAL LOUVERS
CONTROL BUTTON.
Each time the button is pressed, the air flow
direction is changed in the direction of the
arrow.
1 Step
2 Step
3 Step
4 Step
5 Step Left Auto Swing Right Auto Swing
Automatic Air Swing (Vertical)
To adjust the direction of the air flow
automatically, switch OFF 2ndF button
and press
button.
Natural wind (CHAOS Logic)
For fresher feeling, press the INDOOR FAN
SPEED SELECTION BUTTON and set to
Natural wind mode.
In this mode, the wind blows like a natural
breeze by automatically changing fan speed.
2 Press the RESET BUTTON.
3 Press 2ndF button and check if icon is on.
4 Pre ss the
until the desired time is set.
–TIMER–
5 Press the TIMER SET/CANCEL BUTTON.
NOT E Check the indicator for a.m. and p.m.
14
Check if
Press 2 ndF button and check if icon is on.
Press
to set the desired ON time.
ON–TIMER
– The icon below is displayed on the
display screen.
Press
icon is off.
Press the TIMER SET/CANCEL BUTTON
aiming the remote controller at the signal
receiver.
(The timer lamp on the air conditioner and
the display will go off.)
until the desired time is set.
–TIMER–
Press TIMER SET/CANCEL BUTTON
to finish.
Press POWER to turn on the power.
MODE
Press
repeatedly to select the desired
mode.
SLEEP
Press
repeatedly to select the desired
number of hours (up to 7 hours).
- The icon below is displayed on the
display screen
Press 2 ndF button and check if icon is on.
Press
to set the desired OFF time.
TIMER–OFF
– The icon below is displayed on the
display screen.
Press
until the desired time is set.
–TIMER–
Press TIMER SET/CANCEL BUTTON
to finish.
This mode does not have auto restart
feature.
The sleep mode will operat e indoor fan at
sup er low spe ed in coo ling mode and at low
spe ed in heati ng mode for pleasan t sleep
In cooli ng mode or healt hy dehumidifi cation
mode
The sett ing temperat ure will rise autom ati cal ly
two times by 1°C over next con secuti ve 30
minutes (Maxi mum 2°C ) for a com fort abl e
sleep .
Thi s will be the final sett ing temperat ure as
long as sleep mode is func tioni ng.
After com pleti on of set time uni t will switch
OFF autom ati cal ly.
ADVANCED FUNCTIONS 15
Air Purification Mode
(Optional)
LG Air conditioner come with a variety of
filters like Anti-Bacteria filter, Tripple Filter,
Virus & Allergy safe filter, Plasmaster Filter,
which enable you to use it as a Built-in Air
purifier (Even when you are not using it for
cooling,hence minimal electricity consumption).
PLASMA
Press POWER to turn on the power.
JET C
OLO
Press "
" Key. The unit will turn ON,
with only the fan operated and Built-in Air
purifier function is activated.
– PLASMA is displayed on the display screen.
PLASMA
In this mode the compressor will not
operate, hence saves electricity.
This function may not be supported,
depending on the model.
16 ADVANCED FUNCTIONS
PLASMASTER Purification operation
(Optional)
PLASMASTER filter sterilize not only the air going
through the air conditioner, but all surrounding harmfull
substances and even odor.
Press POWER to turn on the power.
PLASMA
Press POWER to turn on the power.
PLASMA
AUTO CLEAN
PLASMA
PLASMA
You can use this function by pressing
without turning the air conditioner on.
Both the Plasmaster lamp and the power
lamp light up while Plasm aster purificati on is
in operation.
During Auto Clean function, “Co” will
be displayed on the unit.
ADVANCED FUNCTIONS 17
Auto operation
Press POWER to turn on the power.
Press
tion.
MODE
repeatedly to select auto opera-
TEMP
22
Please select the code
as per requirement.
Feel
Code
Cold
Slightly Cool
Neutral
Slightly Warm
Warm
18
ADVANCED FUNCTIONS
Quiet Mode Operation (Optional)
This mode minimizes the fan speed of the
system hence making the environment more
comfortable and silent.
1. Press POWER to turn on the power.
2. Open the remote control cover.
QUIET
3. Press
mode button.
Following is displayed on the display screen.
22
Quiet Mode Feature :
In quiet mode unit display shows SL.
In this mode temperature may increase
after some time but only upto 26°C.
This mode has Auto Restart feature. This
means if during this mode, power goes OFF
then unit will restart with the same mode
(Quiet mode) when power comes ON.
This mode does not have auto restart
feature.
Quiet mode will be cancelled by pressing
quiet mode key again.
e-Saver Mode
Dimmer (Optional)
In Dimmer Mode Unit Display will be turned OFF
completely but system will be in running state.
1. Make sure that remote & Air conditioner are ON.
2. Press 2ndF button.
3. Press Dimmer Key to activate/deactivate dimmer
function.
Press POWER to turn on the power.
MODE
Dimmer Mode will be cancelled if any key
except 2ndF Key and Room Key is pressed
(Power Key will turn OFF the Unit.
This mode has Auto Restart feature.
ADVANCED FUNCTIONS 19
8
Cooling Model
Heat pump Model
Room Temp. ³ 24°C
21°C ³ Room Temp. < 24°C
Room Temp. < 21°C
Heating
Operating mode
Cooling
Cooling
Healthy Dehumidification
Indoor FAN Speed
High
High
High
High
Setting Temperature
22°C
22°C
23°C
24°C
20 MAINTENANCE
IONIZER
MAINTENANCE 21
Caution :
Plz do not press the
mesh with finger as
shown above
Outdoor Unit
(Rear)
The heat exchanger coils and panel vents of the outdoor unit should
be checked regularly. If clogged with dirt or soot, the heat exchanger
and panel vents may be professionally steam cleaned.
Air intake
vents
(Side)
Piping
Drain Hose
NOTICE
Dirty or clogged coils will reduce the operating efficiency of the system and
cause higher operating costs.
(Rear)
Air intake
vents
Air outlet
vents
Air outlet
vents
(Rear)
(Side)
Piping
Drain Hose
Air intake
vents
(Side)
Piping
Drain Hose
Air outlet
vents
22 TROUBLESHOOTING
TROUBLESHOOTING 23
When the air conditioner is not going to be used for a long time.
When air conditioner is not going to be
used for a long time.
When the air conditioner is to be used again.
• This will dry out the internal mechanisms.
Clean the air filter and install it in the indoor
unit.
(Refer to page 26 for cleaning filters.)
Turn off the circuit breaker, and disconnect
the plug.
Check that the air inlet and outlet of the
indoor/outdoor unit are not blocked.
Operate the air conditioner on Air circulation
mode (Refer to page 23) for 2 to 3 hours.
CAUTION
Turn off the circuit breaker when the air conditioner
is not going to be used for a long time.
Dirt may collect and may cause a fire.
Remove the batteries from the remote
control.
For any further information, please contact LGEIL Branches
BRANCH
Ahmedabad
BRANCH OFFICE ADDRESS
PHONE NO. / FAX NO.
LGEIL, 233-234, Platinum Plaza, Nr. Judges Bunglow Cross Road, Bodakdev,
Ahmedabad-54
Asansol
LGEIL, Block-E, Ist Floor, P C Chattarjee Market, Rambandhu Tala, GT Road (E)
Asansol-713303
Aurangabad
LGEIL, 302 CIDCO No. 3, Opp. Hotel Ramgiri, Jalna Road, Aurangabad-431003
Bangalore
LGEIL, No. 914, 2nd Floor, Shri Venkateshwara Complex, Opp. IBP Petrol Bunk,
80ft Road, 6th Block, Koramangala - Banglore - 560095
Bhopal
LG Electronics India Private Limited, 2nd Floor, Alankar Complex, Plot No. 10,
M.P. Nagar, Zone-II, Bhopal-462011
Bhubaneshwar LGEIL, Plot No. 02,1st Flr., Bapuji Nagar, Bhubaneshwar-751009
Calcutta
LGEIL, 1, Ho-Chi-Min-Sarani, 6th Floor, Metro Towers, Calcutta-700071
Chandigarh
LGEIL, SCO No. 142-143, 3rd Floor, Sector-34A, Chandigarh-160002
Chennai
LGEIL, AA11, 2nd Avenue, Fatima Tower, Anna Nagar West, Chennai-600040
Cochin
LGEIL, 40/1270, Vasudeva Buildings, T.D. Road, Ernakulam Cochin-682011
Coimbatore
LGEIL, 250A, Sanganur Main Road, Kannappa Nagar, Coimbatore-641027
Delhi
LGEIL, A-27, Mohan Co-operative, Industrial Estate, New Delhi
Dehradun
LGEIL, M-22, Commercial Motors Compound, Mohabewala Indl. Area,
Delhi-Saharanpur Road, Dehradun (Uttarakhand)
Gurgaon
LGEIL, IInd Flr, A Block, Centre Point Bldg, Sushant Lok , Ph-I, Gurgaon-122001
Ghaziabad
LGEIL, J-10, RDC Rajnagar, Ghaziabad - 201001
Guwahati
LGEIL, Shantineer Bhawan, C K Aggarwal Path, Chenikurthi, Guwahati-781003
Hyderabad
LGEIL, 1st Floor, Survey No. 54, Pulla Reddy Building, Vikarampuri,
Main Road, Kharkhana, Secunderabad-500009
Hubli
LGEIL, 1 Floor, Above Bellad & Co., Near Bannigida Busstop, Gokul Road,
Hubli-580030
Indore
LGEIL, 3rd flr., 304 Bansi Trade Centre, 581/5 M.G. Road, Indore-452003
Jaipur
LGEIL, B-71, Sahakar Marg, Lal Kothi Scheme, Jaipur-302015
Jammu
LGEIL, Plot No. 52, Yard No. 6,Transport Nagar, Narwal, Jammu-180006
Jodhpur
LGEIL, 22(1-A)/21(2-B)/2, RIICO Heavy Industrial Area, Jodhpur-342003
Karnal
LG Electronics India Pvt Ltd, Super Tyre Building, Near New Anaj Mandi,
Opp. New World Restauarnt, G.T. Road Karnal, Haryana
Lucknow
LGEIL, B-537, Hari Kunj, Keshav Nagar, Sitapur Road, Lucknow-226020
Ludhiana
LGEIL, Village Jhande, Near Badowal Railway Station,
Opp. Ferozpur Road, Ludhiana.
Mumbai(N & S) LGEIL, Trade Star, 4th Floor, A Wing, J.B. Nagar, Andheri Kurla Road,
Andheri (E) Mumbai-400059
Nagpur
LGEIL, 5A, Road No.13, Behind Msrtc Workshop, MIDC Hinga, Nagpur-440016
Patna
LGEIL, 2nd Floor, Ankit Chandra Deep Complex, Bander Bageecha,
Near Samrat Hotel, Patna-800001.
Pune
LGEIL, 105/106, Premium Point, GM Road, Opp. Modern High School,
IIIrd Floor, Shivaji Marg, Pune-411005
Rajkot
LGEIL, Sanskruti Apartment, Opp. Dr. Ambedkar Bhawan, Near Atithi Chowk,
Akshar Road , Rajkot - 360004
Raipur
613 to 616 , 6th Floor, Offizo, Magneto - The Mall, GE Road,
Raipur - 492001
Ranchi
LGEIL, 402, Commerce Tower, Opp. Gel Church Complex, Main Road, Ranchi
Surat
LGEIL, 1001-1004, Ascon Plaza, IInd Flr, Anand Mahal Road,
Behind Bhulka Bhavan School, Adajan, Surat-395009
Thane
LGEIL, Gall Shop No - 206,207, 2nd Floor, Sai Plaza , Above Vijay Sales
Opp. Cine Wonder Mall, Ghodbunder Road , Thane(West)-400607
Varanasi
LGEIL, Pama Complex, DLW, Lahartara Road, Shivdaspur, Manduadih,
Varanasi, UP-221002
Vijaywada
LGEIL, Door No. 32-2/1-7, Ratnamamba Street, Prajasakti Nagar,
Vijaywada-520010, Andhra Pradesh
Warangal
LGEIL, House No. 1-8-598/1, First Floor, Beside HDFC Bank, Nakkalgutta,
Hanamakonda-506001 (Warangal)
Kozhikode
3/568, Thripuri Building, Wayanadu Road, First Floor,Near K.S.F.E,
East Nadakkavu, Calicut-673011
40040013-14
3292009/3292010 (Fax) 2215170
5625705 / (Fax) 2474055/32095436/32095437/32095438
41145145/41144750/41144751
4262847/4229861 (Fax) 4262848
2531430, 2534280
22883254 (51) Fax
5087389\90 (Fax) 5089107
65510501~04 (Fax) 26203506
2369765/2369743/2370744/4027444/4027555/2360977 (Fax)
2332197, 2332195
26991412/11/13 (Fax) 26991410
2644213/283
4047461- 62 - 63/4272867, 4047460 (Fax)
9811354152/3/64/65/266
2663895/2666958/2665983/2668984 (Telefax)
27207504, 05, 06/27204094 27201462 (Fax)
4250251/52
4065523~24, 4082157 (Fax)
5111118/5113028/5105392, 5111540 (Fax)
2477420, 2477419, 2474396, 2474384
2742384, 392 / 5120030 (Fax)
2219201, 2219202 (Telefax)
2757538,39,2759121 (Fax) 2757559
2804412 - 19
28352882-2887 / 28352889 (Fax)
235120, 235122, Fax : 234401
3298714, 2541845 (Fax)
66030100,732/733/734/735, 66030740 (Fax)
2481499,2467692 (Fax)
4053171/4037470 (Fax) 4038426/10/11
3294026, 2331815
2730982/83, 2730984 (Fax)
25472633/2637
25472602(Fax)
2373432/36/37
2497283/87, (Fax) 2497284
2551453
2366755, 2366756, 2366678, (Fax) 2766678
Email : serviceindia@lge.com
LG Electronics
Pipe Size
1/4"
3/8"
9K
LIQUID
GAS
Capacity
(Btu/h)
9K, 12K,
18K (50Hz)
18K (60Hz)
24K Cooling
24K, 26K
Cooling & Heat Pump
3/8"
5/8"
1/4"
5/8"
1/4"
1/2"
20
3 to 5
Max.
length
A (m)
Standard
Length
(m)
3 to 5
3 to 5
3 to 5
20
20
20
INSTALLATION 27
Additional
Refrigerant
(g/m)
20
20
20
20
Outdoor unit
A
Indoor unit
Outdoor unit
A
Oil trap
Indoor unit
In case more than 5m
CAUTION
Capacity is based on standard length and maximum
allowance length is on the basis of reliability.
Oil trap should be installed every 5~7 meters.
26 INSTALLATION
INSTALLATION 25
24 INSTALLATION
INSTALLATION 23
22 INSTALLATION
INSTALLATION 21
20 INSTALLATION
2
1
Connect the cable to the
outdoor unit
A
Remove the control cover from the unit by
loosening the screw.
Connect the wires to the terminals on the
control board individually.
B Secure the cable onto the control board with
the cord clamp.
C Refix the control cover to the original
position with the screw.
D
INSTALLATION 19
Outdoor Unit
Terminal block
Over 5mm
Connecting cable
Connecting cable
Cover Control
control
Use a recognized circuit breaker 20A (18K),
25A (24K, 26K) between the power source
and the unit. A disconnecting device to
adequately disconnect all supply lines must
be fitted.
CAUTION
After the confirmation of the above conditions, prepare the wiring as follows:
1) Never fail to have an individual power circuit specifically for the air conditioner. As for
the method of wiring, be guided by the circuit diagram posted on the inside of control
cover.
2) The screw which fasten the wiring in the casing of electrical fittings are liable to come
loose from vibrations to which the unit is subjected during the course of
transportation. Check them and make sure that they are all tightly fastened. (If they
are loose, it could cause burn-out of the wires.)
3) Specification of power source.
4) Confirm that electrical capability is sufficient.
5) See to that the starting voltage is maintained at more than 90 percent of the rated
voltage marked on the name plate.
6) Confirm that the cable thickness is as specified in the power source specification.
(Particularly note the relation between cable length and thickness. (Refer to page 11))
7) Always install an earth leakage circuit breaker in a wet or moist area.
8) The following would be caused by voltage drop.
Vibration of a magnetic switch, which will damage the contact point, fuse breaking, disturbance of the
normal function of the overload.
9) The means for disconnection from a power supply shall be incorporated in the fixed
wiring and have an air gap contact separation of at least 3mm in each active(phase)
conductors.
18 INSTALLATION
Connecting the Cables between Indoor Unit and Outdoor Unit
1
Connect the cable from
Indoor to outdoor unit.
Connect the cable to the indoor unit by
connecting the wires to the terminals on the
control board individually according to the
outdoor unit connection.
CAUTION
The power cord connected to the indoor unit should
be compiled with the following specifications
(Type H05VV-F approved by HAR or SAA).
Capacity
(Btu/h)
(Ensure that the color of the wires of the
outdoor unit and the terminal No. are the same
as those of the indoor unit.)
Cooling model (2.0 Ton)
IDU Terminal
1(L)
Cooling model (1.5, 1.0 Ton)
2(N)
BLACK GREEN YELLOW
RED
BLACK GREEN YELLOW
RED
Color of Wires
BLACK
G/Y
1(L)
RED
Color of Wires
BLACK
G/Y
ODU Terminal
RED
Connector of
Indoor Unit
Lock the
connectors
properly
2(N)
Color of Wires
RED
Color of Wires
Color of Wires
BLACK
RED
2(N)
3
G/Y
BLUE BROWN
3
4
5
6
1.0mm2
2.5mm2
NORMAL CROSS
-SECTIONAL AREA
1.0mm2
9K, 12K
NORMAL
CROSS-SECTIONAL
AREA 0.75mm 2
4
BLUE BROWN
G/Y
2
2.5mm2
The connecting cable connected to the indoor and
outdoor unit should be compiled with the following
specifications
(Type H07RN-F approved by HAR or SAA).
BLACK GREEN YELLOW
1(L) 2(N)
BLACK
RED
1
NORMAL CROSS
-SECTIONAL AREA
1.5mm2
18K
9K, 12K
24K
26K
The power connecting cable connected to the
indoor and outdoor unit should be compiled with the
following specifications
(Type H07RN-F approved by HAR or SAA).
Capacity
(Btu/h)
Connector of
Inter-connecting
cable
2.0mm2
18K
24K
26K
1(L)
ODU Terminal
Screw the
Wire on
Control Panel
Heat pump model
Terminals on the indoor unit
Color of Wires
Terminals on the outdoor unit
The length of the power supply cord should be
over 1.8m measured from the power supply cord
entry of the cabinet to the middle of the live pin
of the plug.
CAUTION
If a power plug is not to be used, provide a circuit breaker between power source and the unit as shown below.
Main power source
Air
Conditioner
Circuit Breaker
Use a circuit
breaker or time
delay fuse.
INSTALLATION 17
16 INSTALLATION
INSTALLATION 15
14 INSTALLATION
INSTALLATION 13
12 INSTALLATION
INSTALLATION
11
INSTALLATION MANUAL
AIR CONDITIONER
Please read this installation manual completely before installing the product.
When the power cord is damaged, replacement work shall be
performed by authorized personnel on;y.
Installation work must be performed in accordance with the national wiring
standards by authorized personnel only.
Please retain this installation manual for
future reference after reading it thoroughly.
TYPE : WALL MOUNTED
LG Electronics India Pvt. Ltd.
P/No. MFL39754854
Registered Office : A-27, Mohan Co-operative
Industrial Estate, Mathura Road, New Delhi-110044
Tel: 011-26991412, Fax: 011-26991410
www.lg.com
Download PDF

advertising