LG | LSN6NW2VF1 | LG LSN6NW2VF1 Owner’s Manual

Owner's Manual
Please read this manual carefully before operating the unit.
MTNL / BSNL (Toll Free)
Prefix STD Code
P/No.: MFL39754816
LG Electronics India Pvt. Ltd.
Registered Office: Plot No. 51, Surajpur Kasna Road, Greater Noida - 201 306 (U.P.) INDIA Tel: 0120-2560900 Fax: 0120-2560957
Room Air Conditioner Owner’s Manual
TABLE OF CONTENTS
Safety Precautions.........................3
FOR YOUR RECORDS
Write the model and serial numbers here:
Model #
Serial #
Prior to Operation ..........................9
You can find them on a label on the side of each unit.
Dealer's Name
Date Purchased
Introduction ..................................10
Electrical Safety ...........................11
Operating Instructions.................12
Maintenance and Service ............25
n Staple your receipt to this page in the event you need
it to prove date of purchase or for warranty issues.
READ THIS MANUAL
Inside you will find many helpful hints on how to use
and maintain your air conditioner properly. Just a little
preventive care on your part can save you a great deal
of time and money over the life of your air conditioner.
You'll find many answers to common problems in the
chart of troubleshooting tips. If you review our chart of
Troubleshooting Tips first, you may not need to call
for service at all.
PRECAUTION
• Contact the authorized service technician for repair or
maintenance of this unit.
• Please install your air-conditioner by company
authorised service franchisee / authorised service
and sales dealer.
• The air conditioner is not intended for use by young
children or invalids without supervision.
• Young children should be supervised to ensure that
they do not play with the air conditioner.
• When the power cord is to be replaced, replacement
work shall be performed by authorized personnel only,
using only genuine replacement parts.
We recommend usage of voltage stabilizer with
high / low voltage cut off in areas having voltage
fluctuations.
2 Room Air Conditioner
AC TONNAGE
STABILIZER KVA
(3-STEP STABILIZER)
1.0
1.5
2.0
3
4
5
Safety Precautions
Safety Precautions
To prevent the injury of the user or other people and property damage, the following instructions must be
followed.
n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified
by the following indications.
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to properties only.
n The meanings of the symbols used in this manual are as shown below.
Be sure not to do.
Be sure to follow the instruction.
n Installation
Do not use damaged power
cords, plugs, or a loose
socket.
• There is risk of fire or electric
shock.
Install the panel and the
cover of control box
securely.
• There is risk of fire or electric
shock.
For electrical work, contact
the dealer, seller, a qualified
electrician, or an Authorized
Service Center.
• There is risk of fire or electric
shock.
Do not modify or extend the
power cord.
• There is risk of fire or electric
shock.
Always use the power plug
and socket with the ground
terminal.
• There is risk of electric shock.
Do not install, remove, or
re-install the unit by
yourself (customer).
• There is risk of fire, electric
shock, explosion, or injury.
Owner's Manual 3
Safety Precautions
Be cautious when
unpacking and installing
the product.
• Sharp edges could cause injury.
Be especially careful of the
case edges and the fins on the
condenser and evaporator.
Be sure the installation area
does not deteriorate with
age.
• If the base collapses, the air
conditioner could fall with it, causing
property damage, product failure,
and personal injury.
For installation, always
contact the dealer or an
Authorized Service Center.
• There is risk of fire, electric
shock, explosion, or injury.
Do not install the product
on a defective installation
stand.
• It may cause injury, accident, or
damage to the product.
Do not let the air conditioner
run for a long time when the
humidity is very high and a
door or a window is left open.
• Moisture may condense and
wet or damage furnishings.
n Operation
Take care to ensure that
power cords could not be
pulled out or damaged
during operation.
Do not place anything on
the power cord.
Do not turn the
air-conditioner ON or OFF
by plugging or unplugging
the power plug.
• There is risk of fire or electrical
shock.
• There is risk of fire or electric
shock.
• There is risk of fire or electrical
shock.
4 Room Air Conditioner
Safety Precautions
Use a dedicated outlet for
this appliance.
Grasp the plug to remove
the cord from the outlet. Do
not touch it with wet hands.
Do not place a heater or
other appliances near the
power cable.
• There is risk of fire or electrical
shock.
• There is risk of fire or electrical
shock.
• There is risk of fire and electric
shock.
Do not allow water to run
into electric parts.
Do not store or use
flammable gas or
combustibles near the air
conditioner.
Do not use the product in a
tightly closed space for a
long time.
• It may cause There is risk of
fire, failure of the product, or
electric shock.
• There is risk of fire or failure of
product.
• Oxygen deficiency could occur.
x
Wa Thinner
When flammable gas leaks,
turn off the gas and open a
window for ventilation
before turn the product on.
DO NOT use the telephone
or turn switches on or off.
Unplug the unit if strange
sounds, odors, or smoke
comes from it.
• There is risk of explosion or fire.
• There is risk of electrical shock
or fire
Stop operation and close
the window in storm or
hurricane. If possible,
remove the air conditioner
from the window before the
hurricane arrives.
• There is risk of property
damage, failure of product, or
electric shock.
Owner's Manual 5
Safety Precautions
Do not open the inlet grill of
the product during
operation. (Do not touch the
electrostatic filter, if the unit
is so equipped.)
• There is risk of physical injury,
electric shock, or product
failure.
Unplug the appliance before
performing cleaning or
maintenance.
• There is risk of electrical shock.
When the product is soaked
(flooded or submerged),
contact an Authorized
Service Center.
• There is risk of fire or eletric
shock.
When the product is not be
used for a long time,
disconnect the power supply
plug or turn off the breaker.
• There is risk of product damage
or failure, or unintended
operation.
Ventilate the product from
time to time when operating
it together with a stove, etc.
• There is risk of fire or electrical
shock.
Take care to ensure that
nobody could step on or fall
onto the outdoor unit.
• This could result in personal
injury and product damage.
n Installation
Always check for gas
(refrigerant) leakage after
installation or repair of
product.
• Low refrigerant levels may
cause failure of product.
Install the drain hose to
ensure that water is drained
away properly.
• A bad connection may cause
water leakage.
Keep level even when
installing the product.
• To avoid vibration or water
leakage.
90û
6 Room Air Conditioner
Safety Precautions
Do not install the product
where the noise or hot air
from the outdoor unit could
damage the neighborhoods.
• It may cause a problem for your
neighbors.
Use two or more people to
lift and transport the air
conditioner.
• Avoid personal injury.
Do not install the product
where it will be exposed to
sea wind (salt spray)
directly.
• It may cause corrosion on the
product. Corrosion, particularly on
the condenser and evaporator fins,
could cause product malfunction
or inefficient operation.
n Operation
Do not direct airflow at
room occupants. (Don't sit
in the draft.)
Do not use the product for
special purposes, such as
preserving foods, works of
art, etc. It is a consumer air
conditioner, not a precision
refrigeration system.
Do not block the inlet or
outlet of air flow.
• This could damage your health.
• There is risk of damage or loss
of property.
• It may cause product failure.
Use a soft cloth to clean. Do
not use harsh detergents,
solvents, etc.
Do not touch the metal
parts of the product when
removing the air filter. They
are very sharp!
Do not step on or put
anyting on the product.
(outdoor units)
• There is risk of fire, electric
shock, or damage to the plastic
parts of the product.
• There is risk of personal injury.
• There is risk of personal injury
and failure of product.
Owner's Manual 7
Safety Precautions
Always insert the filter
securely. Clean the filter
every two weeks or more
often if necessary.
• A dirty filter reduces the
efficiency of the air conditioner
and could cause product
malfunction or damage.
Do not insert hands or other
objects through the air inlet
or outlet while the air
conditioner is plugged in.
• There are sharp and moving
parts that could cause personal
injury.
Use a firm stool or ladder when cleaning or
maintaining the air conditioner.
• Be careful and avoid personal injury.
Do not drink the water
drained from the unit.
• It is not sanitary and could
cause serious health issues.
Replace the all batteries in the remote
control with new ones of the same type. Do
not mix old and new batteries or different
types of batteries.
• There is risk of fire or explosion
n Disuse
Do not recharge or disassemble the
batteries. Do not dispose of batteries in a
fire.
• They may burn or explode.
8 Room Air Conditioner
If the liquid from the batteries gets onto
your skin or clothes, wash it well with clean
water. Do not use the remote if the batteries
have leaked.
• The chemicals in batteries could cause burns or
other health hazards.
Prior to Operation
Prior to Operation
Preparing for Operation
1. Contact an installation specialist for installation.
2. Plug in the power plug properly.
3. Use a dedicated circuit.
4. Do not use an extension cord.
5. Do not start/stop operation by plugging/unplugging the power cord.
6. If the cord/plug is damaged, replace it with only an authorized replacement part.
Usage
1. Being exposed to direct airflow for a long time may be hazardous to your health. Do not expose
occupants, pets, or plants to direct airflow for a long time.
2. Due to the possibility of oxygen deficiency, ventilate the room when using the appliance together with
stoves or other heating devices.
3. Do not use this air conditioner for non-specified special purpose (e.g. preserving precision devices,
food, pets, plants, or art objects). Such use may damage your properties.
Cleaning and Maintenance
1. Do not touch the metal parts of the unit when removing the filter. Injury can occur.
2. Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation,
leading to electric shock.
3. When cleaning the unit, first make sure that the power and breaker are turned off. The fan rotates at a
very high speed during operation. There is a possibility of injury if the unit’s power is triggered while
cleaning inner parts of the unit.
Service
For repair and maintenance, contact your authorized service dealer.
Owner's Manual 9
Introduction
Introduction
Symbols used in this Manual
This symbol alerts you to the risk of electric shock.
This symbol alerts you to hazards that may cause harm to the
air conditioner.
NOTICE
This symbol indicates special notes.
Features
This appliance should be installed in accordance with national wiring regulations. This guide acts as a
guide to help to explain product features.
Indoor
Air Inlet
Signal Receptor
Air Filter
Front Panel
Outdoor
Air Intake Vents
Connecting
Wires
Piping
Air Outlet Vents
Base Plate
10 Room Air Conditioner
Drain Hose
Electrical Safety
Electrical Safety
• This appliance must be properly grounded.
To minimize the risk of electric shock, you must always plug into a grounded outlet.
• Do not cut or remove the grounding.
• Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance
unless the cover screw is metal and not insulated, and the wall receptacle is grounded through the
house wiring.
• If you have any doubt whether the air conditioner is properly grounded, have the wall receptacle and
circuit checked by a qualified electrician.
Owner's Manual 11
Operating Instructions
Operating Instructions
How to insert the Batteries
1 Remove the battery cover by pulling it according to the
arrow direction.
2 Insert new batteries making sure that the (+) and (-) of
battery are installed correctly.
3 Reattach the cover by sliding it back into position.
NOTES:
Use 2 AAA(1.5volt) batteries. Do not use rechargeable
batteries.
Storage and Tips for using the Remote Controller
• The remote controller may be stored by mounting
it on a wall.
• To operate the room air conditioner, aim the
remote controller at the signal receptor.
Signal Receptor
Receives the signals from the remote control.(Signal receiving sound: two short beeps or one long beep.)
Operation Indication Lamps
On/Off
: Lights up during the system operation.
Sleep Mode
: Lights up during Sleep Mode Auto operation.
Timer
: Lights up during Timer operation.
OUTDOOR UNIT : Lights up during outdoor unit operation.
OPERATION
(Cooling model only)
Signal
receptor
* Optional feature, available in selected models.
12 Room Air Conditioner
Operation indication
lamps
Operating Instructions
Remote Control Operations
The remote control transmits the signals to the system.
Features of the Remote Control- Door Closed
Signal transmitter
Signal transmitter
JET COOL TEMP A/SWING
6
5
6
5
FAN SPEED
4
1
Signal transmitter
5
6
1
POWER
4
3
FAN SPEED
2
2
TYPE A
1
4
3
MODE
POWER
TEMP
1
3
2
L A/SWING
JET COO
3
4
Flip-up door
(closed)
5
6
Signal transmitter
Flip-up door
(closed)
TYPE B
START/STOP BUTTON
1 Operation
starts when this button is
MODE
2
ON
ON
Flip-up door
(closed)
Flip-up door
(closed)
TYPE C
TYPE D
INDOOR FAN SPEED
4 SELECTOR
Used to select fan speed in four steps
low, medium, high, or CHAOS.
pressed and stops when the button is
pressed again.
OPERATION MODE
2 SELECTION
BUTTON
JET COOL
5 Used
to start or stop the speed
ROOM TEMPERATURE
3 SETTING
BUTTONS
6
Used to select the operation mode.
Used to select the room temperature.
cooling. (Speed cooling operates
super high fan speed in cooling mode).
AIR SWING BUTTON
Used to stop or start louver movement and
set the desired up/down airflow direction.
Operation Mode
Cooling Operation
Cooling Operation
Auto Operation
Auto Operation
Healthy Dehumidification Operation
Healthy Dehumidification Operation
Heating Operation
(Cooling Model)
(Heat Pump Model)
* Your unit shall have either Type A,Type B, Type C or Type D Remote Control
Owner's Manual 13
Operating Instructions
Features of the Remote Control- Door Opened
Signal
transmitter
ON/OFF TIMER BUTTONS
1 Used
to set the time of starting and stopping
operation.
Signal
transmitter
TIME SETTING BUTTONS
2 Used
to adjust the time, (See page 15)
TIMER SET/CANCEL BUTTONS
3 Used
to set the timer when the desired time is
1
ON
OFF
SET
CANCEL
obtained and to cancel the Timer operation.
(See page 15)
4
5
2
3
JET COOL TEMP
6
PLASMA
FAN SPEED
7
8
A/SWING
POWER
SLEEP MODE AUTO BUTTON
4 Used
to set Sleep Mode Auto operation.
9
ON TIMER OFF
1
SLEEP
SET
3
CANCEL
MODE
4
FAN
TIMER
2
AIRFLOW
(See page 15)
5
ROOM
6
PLASMA
7
AIR CIRCULATION BUTTON
5 Used
to circulate the room air without cooling
RESET
8
9
or heating. (See page 16)
Signal
transmitter
ROOM TEMPERATURE
6 CHECKING BUTTON
Used to check the room temperature.
Signal
transmitter
7
4
HORIZONTAL AIRFLOW
CANCEL
1
5
2
7
3
ON
OFF
JET CO
SET
A/SWING
OL
6
8 DIRECTION CONTROL BUTTON
POWER
TEMP
(OPTIONAL)
8
9
Used to set the desired horizontal airflow
direction. (See page 16)
FAN SPEED
10
4
MODE
Flip-up door
(opened)
PLASMA (OPTIONAL)
Used to start or stop the plasma-purification
function. (See page 13)
1
5
2
7
SLEEP
ON TIMER OFF
FAN
ROOM
CANCEL
SET
TIMER
AIRFLOW
9
3
6
8
10
9
RESET BUTTON
Used prior to resetting time or after replacing
batteries.
2nd F Button (Type C or Type D
Flip-up door
(opened)
14 Room Air Conditioner
10 Remote Control)
Used prior to using modes printed in blue at
the bottom of buttons. (See page 14)
Operating Instructions
How to use the Operation Mode Selection button
Cooling Operation
1
Press the Start/Stop button.
The unit will respond with
a beep.
2
Open the door on the remote control. To select Cooling
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the arrow.
POWER
MODE
Cooling
3
JET COOL
FAN SPEED
TEMP
Auto
Healthy
Dehumidification
Heating
(Heat pump model only)
Close the door on the remote control. Set the temperature
higher than the room temperature. The temperature can be
set within a range of 18°C~30°C in 1°C increments.
A/SWING
To raise the temperature
POWER
To lower the temperature
MODE
4
Set the fan speed again with the door
of the remote control still closed. You
can select the fan speed in four stepslow, medium, high or CHAOS. Each
time the button is pressed, the fan
speed mode is shifted.
FAN SPEED
Natural wind by the CHAOS logic
For more fresh feeling than other fan speed, press the Indoor Fan Speed Selector and set to
CHAOS mode. In this mode, the wind blows like natural breeze by automatically changing fan
speed according to the CHAOS logic.
Owner's Manual 15
Operating Instructions
Auto Operation
1
Press the Start/Stop button.
The unit will respond with
a beep.
2
Open the door on the remote control. To select Auto
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the arrow.
POWER
MODE
Cooling
JET COOL
FAN SPEED
TEMP
A/SWING
POWER
3
Auto
Healthy
Heating
Dehumidification (Heat pump model only)
The temperature and fan speed are automatically set by the
electronic controls based on the actual room temperature. If
you want to change the set temperature, close the door on
the remote control and press the Room Temperature Setting
buttons. The cooler or warmer you feel, the more times (up to
two times) you should press the button. The set temperature
will be changed automatically.
MODE
To raise the temperature
To lower the temperature
During Auto Operation:
You cannot switch the indoor fan speed. It has already been set by the Fuzzy rule.
If the system is not operating as desired, manually switch to another mode. The system will not
automatically switch from the cooling mode to the heating mode, or from heating mode to cooling
mode, it must be done by manually resetting.
During Auto Operation, pressing the chaos swing button makes the horizontal louvers swing up and
down automatically. If you want to stop auto-swing, press the chaos swing button again.
16 Room Air Conditioner
Operating Instructions
Healthy Dehumidification Operation
1
Press the Start/Stop button.
The unit will respond with
a beep.
2
Open the door on the remote control. To select Healthy
Dehumidification Operation, press the Operation Mode
Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the arrow.
POWER
MODE
Cooling
3
JET COOL
FAN SPEED
MODE
TEMP
A/SWING
POWER
Auto
Healthy
Heating
Dehumidification (Heat pump model only)
Set the fan speed again with the door
of the remote control still closed. You
can select the fan speed in four stepslow, medium, high, or CHAOS. Each
time the button is pressed, the fan
speed mode is shifted.
FAN SPEED
Natural wind by the CHAOS logic
For more fresh feeling than other fan speed, press the Indoor Fan
Speed Selector and set to CHAOS mode. In this mode, the wind
blows like natural breeze by automatically changing fan speed
according to the CHAOS logic.
During Healthy Dehumidification Operation:
If you select the dehumidification mode on the operation selection button, the A/C starts to run the
dehumidification function. It automatically sets the room temp. and airflow volume to the best condition
for dehumidification, based on the sensed current room temp.
In this case, however, the setting temp. is not displayed in the remote control and you are not able to
control the room temp. either.
During the healthy dehumidification function, the airflow volume is automatically set according to the
optimization algorithm responding to the current room temp. status which makes the room condition
healthy and comfortable even in the high humidity season.
Owner's Manual 17
Operating Instructions
Heating Operation(Heat pump model only)
1
Press the Start/Stop button.
The unit will respond with
a beep.
2
Open the door on the remote control. To select Heating
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the arrow.
POWER
MODE
Cooling
3
JET COOL
TEMP
Auto
Healthy
Heating
Dehumidification (Heat pump model only)
Close the door on the remote control.
Set the temperature higher than the room temperature.
The temperature can be set within a range of 16°C~30°C in
1°C increments.
A/SWING
To raise the temperature
FAN SPEED
POWER
To lower the temperature
MODE
4
Set the fan speed again with the door of the
remote control still closed. You can select
the fan speed in four steps–low, medium,
high or CHAOS. Each time the button is
pressed, the fan speed mode is shifted.
FAN SPEED
Natural wind by the CHAOS logic
For more fresh feeling than other fan speed, press the Indoor Fan Speed Selector and set to
CHAOS mode. In this mode, the wind blows like natural breeze by automatically changing fan
speed according to the CHAOS logic.
18 Room Air Conditioner
Operating Instructions
Jet Cool Operation
JET COOL
FAN SPEED
TEMP
A/SWING
1
Press the Start/Stop button.
The unit will respond with
a beep.
2
Press the Jet Cool button to operate
the speed cooling mode and the unit
will operate in super high fan speed
on cooling mode for 30 minutes.
3
To cancel the Jet Cool mode, press the Jet Cool button
again or the fan speed button or the room temperature
setting button and the unit will operate in high fan speed on
cooling mode.
POWER
JET COOL
POWER
TEMP
FAN SPEED
JET COOL
or
or
NOTE:
During the JET COOL function at any moment, the A/C starts to blow the cool air at
extremely high speed for 30 minutes setting the room temp. automatically to 18°C. It is
especially used to cool the room temp. in the shortest time in a hot summer.
In heat pump mode or neuro fuzzy mode, however, the JET COOL function is not available.
In order to return to the normal cooling mode from the JET COOL mode, you just press
either the operation mode selection button, airflow volume selection or temp. setting button
or the JET COOL button again.
Owner's Manual 19
Operating Instructions
PLASMA Purification Operation(Optional)
1
Press the Start/Stop button.
The unit will respond with a
beep.
2
Open the door on the remote control.
Press the PLASMA air purifying
operation ON/OFF button.
Operation will start when the button is
pressed and stop when the button is
pressed again.
3
JET COOL
FAN SPEED
TEMP
A/SWING
POWER
POWER
PLASMA
Set the fan speed again with door of the remote control
closed. You can select the fan speed in four steps-low,
FAN SPEED
medium, high or CHAOS. Each time the
button is pressed, the fan speed mode
is shifted.
Air purifying operation (PLASMA) can be with cooling,
Heating or any other operations.
PLASMA Air Purifying Operation only
PLASMA
20 Room Air Conditioner
If you press the only PLASMA button, PLASMA
air purifying operates only.
Then, fan speed is low. You can select the fan
speed in four steps-low, medium, high or
CHAOS.
Each time the button (
) is pressed, the fan
speed mode is shifed.
Operating Instructions
2nd F Operation
nd
2nd
F
CANCEL
ON
OFF
1
Press the Start/Stop button.
The unit will respond with
a beep.
2
Open the door of the remote control and press the 2nd
Function button to operate functions printed in blue at bottom
of buttons.
(Check the indication of 2nd function on remote control
display.)
These buttons operate the timer setting as follows:
SET
CANCEL
2ndF
ON
OFF
SET
POWER
MODE
SLEEP
ON TIMER OFF
FAN
ROOM
CANCEL
SET
TIMER
JET CO
A/SWING
OL
POWER
TEMP
3
2nd function goes off in a short time automatically or when
the button is pressed again.
FAN SPEED
MODE
SLEEP
ON TIMER OFF
FAN
ROOM
CANCEL
SET
TIMER
AIRFLOW
Owner's Manual 21
Operating Instructions
Additional features
Sleep Mode
1
Press the Sleep Mode Auto button to set the SLEEP
time you want the unit to turn off automatically.
To cancel the Sleep Mode, press the sleep
Mode Auto button several times until the star
(
) disappears from the operation display.
2
The Timer is programmed in one-hour
increments by pressing the Sleep Mode Auto
button 1 to 7 times.
The sleep mode is available for 1 to 7 times. To
alter the time period in steps of 1 hour, press
the Sleep Mode Button while aiming at air
conditioner.
Note: 1. The Sleep Mode will be operated at
slow fan speed (cooling) or medium
fan speed (heat pump only) for quiet
sleeping.
2. Remote Control will display Fan Speed.
Set before sleep mode although Unit
Fan Speed changes.
3
Make sure the Sleep Mode Auto LED lights up.
IN COOLING MODE : The temperature will
automatically rise by 1°C over the next 30
minutes and by 2°C in 1 hour for comfortable
sleeping.
Setting the Time
1
Time can be set only when you have pressed
the Reset button. If you have just replaced the
batteries, the Reset button should be pressed
to reset the time.
Press the Start/Stop button.
POWER
2
Press the Time Setting buttons until the
desired time is set.
TIMER
3
Press the Timer SET button.
SET
Note: Check the indicator
for A.M. and P.M.
Delay Start/Pre-Set Stop
1
Make sure the time is set correctly on the
remote control display.
2
Press the ON/OFF Timer
buttons to turn Timer on or off.
3
Press the Time Setting
buttons until the desired
time is set.
4
ON TIMER OFF
TIMER
Press the selected on/off setting by
pressing the Timer SET button while
aiming the remote control at the signal
receptor.
SET
To cancel the timer setting
Press the Timer Cancel button while
CANCEL
aiming remote control at the signal
receptor.
(The timer lamp on the air conditioner and
the display will go out.)
NOTE: Select one of the following four types of operation.
with the unit running
Delay OFF Timer
22 Room Air Conditioner
Delay ON Timer
Delay OFF and ON Timer Delay ON and OFF Timer
Operating Instructions
Vertical Airflow Direction Control
The up/down airflow (Vertical Airflow) can be
adjusted by using the remote control.
1
Press the Start/Stop button to start the unit.
2
Press Air Swing button and the louvers will
swing up and down. Press the Air Swing
button again to set the vertical louver at the
desired airflow direction.
A/SWING
Note:
If you press the AIR swing button, the horizontal
airflow direction is changed automatically based on the
CHAOS algorithm to distribute the air in the room
evenly and at the same time to make the human body
feel most comfortable, as if enjoying a natural breeze.
Always use the remote control to adjust the up/down
airflow direction. Manually moving the vertical airflow
direction louver by hand, could damage the airconditioner.
When the unit is shut off, the up/down airflow direction
louver will close the air outlet vent of the system.
To adjust left/right(Horizontal Airflow) direction
Caution : Ensure that the unit is turned
off before adjusting the
horizontal airflow direction
control. Carefully open vertical
louver to allow access to the
horizontal airflow direction.
Adjust the left/right airflow direction by hand.
Horizontal Airflow Direction Control (Option)
The left/right(Horizontal Airflow) can be adjusted by using the remote control.
Press the Start/Stop button to start the unit.
Open the door on the remote control. Press the Airflow Direction
Start/Stop button and the louvers will swing left and right. Press
the Horizontal Airflow Direction Control Button again to set the
horizontal louver at the desired airflow direction.
AIRFLOW
Air Circulation Mode
Circulates the room air without cooling or heating.
1
Press the Start/Stop button. the unit will respond with a beep.
2
Open the door on the remote control. Press the Fan button. Close the door on the
remote control. Now each time that you press the Indoor Fan Speed Selector, the fan speed is
shifted from low to CHAOS and back to low again.
FAN
CHAOS Air
Fan speed is on low.
Fan speed is on medium.
Fan speed is on high.
Note:
CHAOS Air economizes power consumption and prevents overcooling. The fan speed is automatically changed
from high to low or vice versa, depending on the ambient temperature.
Owner's Manual 23
Operating Instructions
Forced Operation
Please follow the step 1 to step 5
for forced operation.
1.
2.
3.
4.
5.
Turn ON the unit using power button.
Turn OFF the unit using power button.
Switch OFF the mains supply to the unit.
Switch ON the mains supply to the unit.
Turn ON the unit using the power button.
Open the front
panel upward
After turning ON the unit will operate
according to the table below :
Power
button
Cooling Model
Operating mode
Indoor FAN Speed
Setting Temperature
Cooling
High
22°C
Room Temp. ³ 24°C
Cooling
High
22°C
Heat pump Model
21°C ³ Room Temp. < 24°C
Healthy Dehumidification
High
23°C
Room Temp. < 21°C
Heating
High
24°C
If you want to stop the unit, re-press the power button.
Test operation
During the TEST OPERATION, the unit operates in cooling mode at high speed fan, regardless of room
temperature and unit will stop after18 minutes.
During test operation, if remote controller signal is received, the unit operates as remote controller sets.
If you want to use this operation, Press and hold the ON/OFF button for 3~5 seconds, then the buzzer sound
1 "beep".
If you want to stop the operation, re-press the button.
Auto restart
In case the power comes on again after a power failure, Auto Restarting Operation is the function to
operate procedures automatically to the previous operating conditions.
In the initial mode, the fan operates at a low speed and the compressor starts 2.5~3 minutes later.
As the compressor starts, the fan speed also resumes its previous setting mode.
Note : To Enable/Disable Auto restart function (Applicable for 2.0 Ton models)
1. Press ON/OFF (Power) button, located on the display panel continuously.
After 3 seconds, Buzzer will beep once, then after 3 seconds Buzzer will beep twice.
Release the ON/OFF (Power) button.
You can see the ON/OFF LED blinking.
* If, LED is blinking, as shown in Pattern A, then auto restart function is enabled.
* If, LED is blinking, as shown in Pattern B, then auto restart function is disabled.
ON
ON
ON
ON
ON
Pattern A
ON
ON
ON
ON
ON
ON
Pattern B
OFF
Note:
1)
2)
3)
4)
5)
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Auto restart can/ can not be operated in the following cases :
Power failure and recovery occur very fast
Earthing is not proper
Power supply fluctuations.
Frequency Variations
Installation of site wiring
Helpful information
The cooling capacity indicated in the specification is the value when the fan speed is set to high.
24 Room Air Conditioner
OFF
OFF
OFF
Maintenance and Service
Maintenance and Service
CAUTION:Before performing any maintenance, turn off the main power to the system.
Indoor Unit
Never use any of the followings:
• Water hotter than 40°C
Could cause deformation and/or
discoloration.
• Volatile substances
Could damage the surfaces of the air
conditioner.
Grille, Case, and Remote Control
Turn the system off before cleaning. To
clean, wipe with a soft, dry cloth. Do not
use bleach or abrasives.
NOTE:
Supply power must be disconnected before
cleaning the indoor unit.
Pow
d er
G a s o li n e
1
AIR FILTERS
The air filters behind the
front grille should be
checked and cleaned
once in every 2 weeks or
more often if neccessary.
Lift the front access panel and pull the filter tab
slightly forward to remove the filter.
the filter with a vacuum or warm, soapy
2 Clean
water.
• If dirt is conspicuous, wash with a
solution of detergent in lukewarm water.
• If hot water (40°C or more) is used, it
may be deformed.
3 After washing with water, dry well in the
shade.
4 Re-install the air filter.
PLASMA FILTER, DEODORIZER
FILTER(OPTIONAL)
1 After removing the air filters, pull slightly
The PLASMA filter behind the air filters should be
checked and cleaned once in every 3 months or
more often if necessary.
2 Dip the PLASMA filter into the water mixed
forward to remove the PLASMA filter.
with neutral detergent, for 20~30 minutes.
3 Dry the PLASMA filter in the shade for a day
(Especially, the humidity must be removed
perfectly on this parts).
4 Note the cuts of electric discharge lines.
5 Re-install the PLASMA filter to the original
position.
After removing the air filters, pull slightly
Don’t touch this PLASMA Filter within 10
seconds after opening the inlet grille, it may
cause an electric shock.
1 forward to remove the DEODORIZER filter.
2 Dry in the sunlight for two hours.
Re-install the DEODORIZER filter to the
3 original position.
Owner's Manual 25
Maintenance and Service
Replacement of Purifying Filter(Option)
• Recomended use period : About 2 years
1 Open front panel and remove air
2 Remove air purifying filters.
filters.
3 Insert new air purifying filters.
4 Reinsert air filters and close front
panel.
Air purifying filter
Outdoor Unit
The heat exchanger coils and panel vents of the
outdoor unit should be checked regularly. If clogged
(Side)
with dirt or soot, the heat exchanger and panel Air intake
vents
vents may be professionally steam cleaned.
(Rear)
Piping
Drain Hose
NOTE:
Dirty or clogged coils will reduce the
operating efficiency of the system and cause
higher operating costs.
Air outlet
vents
(Rear)
(Rear)
Air intake vents
(Side)
Air outlet vents
26 Room Air Conditioner
Piping
Drain Hose
Air intake
vents
(Side)
Piping
Drain Hose
Air outlet
vents
Maintenance and Service
When the air conditioner is not going to be used for a long time.
When air conditioner is not going to be
used for a long time.
When the air conditioner is to be used again.
Operate the air conditioner on Air circulation
mode (Refer to page 16) for 2 to 3 hours.
Clean the air filter and install it in the indoor
unit.
(Refer to page 19 for cleaning filters.)
• This will dry out the internal mechanisms.
Turn off the circuit breaker, and disconnect
the plug.
Check that the air inlet and outlet of the
indoor/outdoor unit are not blocked.
CAUTION
Turn off the circuit breaker when the air conditioner
is not going to be used for a long time.
Dirt may collect and may cause a fire.
Remove the batteries from the remote
control.
Operation Tips
Do not overcool the room.
Keep blinds or curtains
closed.
Keep the room temperature
uniform.
This is not good for the health
and wastes electricity.
Do not let direct sunshine enter
the room when the air
conditioner is in operation.
Adjust the vertical and
horizontal airflow direction to
ensure a uniform temperature
in the room.
Make sure that the doors
and windows are shut tight.
Clean the air filter regularly.
Ventilate the room
occasionally.
Avoid opening doors and
windows as much as possible
to keep the cool air in the room.
Blockages in the air filter
reduces the airflow and lowers
the cooling and dehumidifying
effects. Clean at least once in
every two weeks.
Since windows are kept closed,
it is a good idea to open them
and ventilate the room now and
then.
Owner's Manual 27
Maintenance and Service
Before you call for service...
?
Troubleshooting Tips! Save time and money!
Check the following points before requesting repairs or service.... If the fault persists, please
contact your dealer or service center.
Case
The air conditioner does not
operate.
Explanation
• Have you made a mistake in timer operation?
• Has the fuse blown or has the circuit breaker
been tripped?
The room has a peculiar
odor.
• Check that this is not a damp smell exuded by
the walls, carpet, furniture, or cloth items in the
room.
It seems that condensation
is leaking from the air
conditioner.
• Condensation occurs when the airflow from
the air conditioner cools the warm room air.
Air conditioner does not
operate for about 3 minutes
when restarted.
• This is the protector of the mechanism.
• Wait about three minutes and operation will
begin.
Does not cool or heat
effectively.
• Is the air filter dirty? See air filter cleaning
instructions.
• Has the temperature been set incorrectly?
• Are the indoor unit's air inlet or outlet vents
obstructed?
The air conditioner
operation is noisy.
• For a noise that sounds like water flowing.
-This is the sound of freon flowing inside the
air conditioner unit.
• For a noise that sounds like the compressed
air releasing into atmosphere.
-This is the sound of the dehumidifying water
being processed inside the air conditioning
unit.
See page
15
-
-
-
-
18
8
-
-
Remote control display is
faint, or no display at all.
• Are the batteries depleted?
• Are the batteries inserted in the opposite (+)
and (-) directions?
5
Crack sound is heard.
• This sound is generated by the
expansion/constriction of the front panel, etc.
due to changes of temperature.
-
NOTE
WATER RESISTANT: The outdoor side of this appliance is WATER RESISTANT.
The indoor side is not water resistant and should not be exposed to excess water.
28 Room Air Conditioner
For any further information, please contact LGEIL Branches
BRANCH
Ahmedabad
BRANCH OFFICE ADDRESS
STD CODE PHONE NO. / FAX NO.
LGEIL, 233-234, Platinum Plaza, Judges Bunglow Road, Bodakdev Road,
Ahmedabad-51
Asansol
LGEIL, Block-E, Ist Floor, P C Chattarjee Market, Rambandhu Tala, GT Road (E)
Asansol-713303
Aurangabad
LGEIL, 302 CIDCO No. 3, Opp. Hotel Ramgiri, Jalna Road, Aurangabad-431003
Bangalore
LGEIL, No. 914, 2nd Floor, Shri Venkateshwara Complex, Opp. IBP Petrol Bunk,
80ft Road, 6th Block, Koramangala - Banglore - 560095
Bhopal
13A, Vignes Warehousing Corporation, Sector-G, Govindpura Industrial Area,
J K Road, Bhopal
Bhubaneshwar LGEIL, Plot No.02,1st Flr., Bapuji Nagar, Bhubaneshwar-751009
Calcutta
LGEIL, 1, Ho-Chi-Min-Sarani, 6th Floor, Metro Towers, Calcutta-700071
Chandigarh
LGEIL, SCO No. 142-143, 3rd Floor, Sector-34A, Chandigarh-160002
Chennai
LGEIL, AA11, 2nd Avenue, Fatima Tower, Anna Nagar West, Chennai-600040
Cochin
LGEIL, 40/1270, Vasudeva Buildings, T.D. Road, Ernakulam Cochin-682011
Coimbatore
LGEIL, 250A, Sanganur Main Road, Kannappa Nagar, Coimbatore-641027
Delhi
LGEIL, A-27, Mohan Co-operative, Industrial Estate, New Delhi
Dehradun
LGEIL, M-22, Mobbewala, Tata Commercial Compound,
Dehradun-Saharanpur Road, Dehradun
Goa
LGEIL, Plot No. D-3&D-4, Rego Baug, Alto Santacruz, Bambolim, Goa-403
Gurgaon
LGEIL, IInd Flr, A Block, Centre Point Bldg, Sushant Lok , Ph-I, Gurgaon-122001
Ghaziabad
LGEIL, J-10, RDC Rajnagar, Ghaziabad - 201001
Guwahati
LGEIL, Shantineer Bhawan, C K Aggarwal Path, Chenikurthi, Guwahati-781003
Hyderabad
LGEIL, 1st Floor, Survey No. 54, Pulla Reddy Building, Vikarampuri,
Main Road, Kharkhana, Secunderabad-500004
Hubli
LGEIL, 603/1B, Ravi Nagar Road, Behind Renuka Petrol Pump,
Gokul Road, Hubli-580030
Indore
LGEIL, 3rd Flr., 304 Bansi Trade Centre, 581/5 M.G. Road, Indore-452003
Jaipur
LGEIL, B-71, Sahakar Marg, Lal Kothi Scheme, Jaipur-302015
Jammu
LGEIL, Plot No. 52,Yard No. 6,Transport Nagar, Narwal, Jammu-180006
Jalandhar
LGEIL, Opp. Jassi Market, Village Khajurala, Near TVS Godown, GT Road
Jodhpur
LGEIL, 22(1-A)/21(2-B)/2, RIICO Heavy Industrial Area, Jodhpur-342003
Kundli
LGEIL, Sunshine Enterprises, Sunder Cold Storage, GT Karnal Road,
Kundli-Sonipat
Lucknow
LGEIL, B-537, Hari Kunj, Keshav Nagar, Sitapur Road, Lucknow-226020
Ludhiana
LGEIL, Village Jhande, Near Badowal Railway Station,
Opp. Ferozpur Road, Ludhiana.
Mumbai(N & S) LGEIL, Trade Star, 4th Floor, A Wing, J.B. Nagar, Andheri Kurla Road,
Andheri (E) Mumbai-400059
Nagpur
LGEIL, 5A, Road No.13, Behind Msrtc Workshop, MIDC Hinga, Nagpur-440016
Patna
LGEIL, 2nd Floor, Ankit Chandra Deep Complex, Bander Bageecha,
Near Samrat Hotel, Patna-800001.
Pune
LGEIL, 105/106, Premium Point, GM Road, Opp Modern High School,
IIIrd Floor, Shivaji Marg, Pune-411005
Raipur
LGEIL, Nathani Compound, Near Gurudwara, Shyam Nagar,
Katora Talab, Raipur (C.G)
Ranchi
LGEIL, 402, Commerce Tower, Opp. Gel Church Complex, Main Road, Ranchi
Surat
LGEIL, 1001-1004, Ascon Plaza, IInd Flr, Anand Mahal Road,
Behind Bhulka Bhavan School, Adajan, Surat-395009
Thane
LGEIL, Gall Shop No. 6-9, S-2, Golden Park Complex, Hardas Nagar, LBS Marg,
Panchpakhadi, Thane (West)-400602
Varanasi
LGEIL, Pama Complex, DLW, Lahartara Road,Shivdaspur, Manduadih,
Varanasi, UP-221002
Vijaywada
LGEIL, Door No. 32-2/1-7, Ratnamamba Street, Prajasakti Nagar,
Vijaywada-520010, Andhra Pradesh
Warangal
LGEIL, House No. 1-8-598/1, First Floor, Beside HDFC Bank, Nakkalgutta,
Hanamakonda-506001 (Warangal)
079
40040013-14
0341
3292009/3292010 (Fax) 2215170
0240
080
5625705 / (Fax) 2474055/32095436/32095437/32095438
25507201/202 (Fax) 25507203
0755
4062900
0674
033
0172
044
0484
0422
011
0135
2531430, 2534280
22883254/4348 (51) Fax
5087389\90 (Fax) 5089107
65510501~04 (Fax) 26203506
2369765,2369743 ,2370744, 4027444,4027555, 2360977 (Fax)
2332197, 2332195, 2332506, 9843909643
26991412/11/13 (Fax) 26991410
2644213/283
0832
0124
0120
0361
040
3294955/3294956/3294759
4047461- 62 - 63/4272867, 4047460 (Fax)
9811354152/3/64/65/266
2663895/2666958/2665983/2668984 (Telefax)
27207504, 05, 06/27204094 27201462 (Fax)
0836
4250251/52
0731
0141
0191
181
0291
0130
4065523~24, 4082157 (Fax)
5111118/5113028/5105392, 5111540 (Fax)
2477420, 2477419, 2474396, 2474384, Fax : 2474574
24502667/8/9/508025
2742384, 392 / 5120030 (Fax)
2219201, 2219202 (Telefax)
0522
0161
2757538,39,2759121 (Fax) 2757559
2804412 - 19
022
07104
0612
020
28352882-2887 / 28352889 (Fax)
235120, 235122, Fax : 234401
3298714, 2541845 (Fax)
66030100,732/733/734/735, 66030740 (Fax)
0771
4053171/4037470, (Fax) 4038426/10/11
0651
0261
3294026, 2331815
2730982/83, 2730984 (Fax)
022
0542
25472633/2637, 25472602 (Fax)
2373432/36/37
866
2497283/87, (Fax) 2497284
870
2551453
Email : lgservice@lgindia.com
LG Electronics
TEST RUNNING
1. Check that all tubing and wiring have been
properly connected.
2. Check that the gas and liquid side service valves
are fully open.
3. Ensure the difference between the intake
temperature and the discharge is more than 8°C
(Cooling) or reversely (Heating).
A Prepare remote control
Intake temperature
Discharge air
1 Remove the battery cover
by pulling it according to the
arrow direction.
2
1 Insert new batteries making
sure that the (+) and (–) of
battery are installed correctly.
Discharge
temperature
3
1 Reattach the cover by
pushing it back into position.
4. For reference; the gas side pressure of optimum
condition is as below.(Cooling)
NOTE:
Use 2 AAA(1.5volt) batteries. Do not use
rechargeable batteries.
Remove the batteries from the remote control if
the system is not going to be used for a long
time.
B Settlement of outdoor unit
Anchor the outdoor unit with a bolt and nut ø10mm)
tightly and horizontally on a concrete or rigid mount.
When installing on the wall, roof or rooftop, anchor
the mounting base securely with a nail or wire
assuming the influence of wind and earthquake.
In the case when the vibration of the unit is
conveyed to the hose, secure the unit with an
anti-vibration rubber.
Outside ambient TEMP. The pressure of the gas side service valve
35°C(95°F)
4~5kg/cm2 G(56.8~71.0 P.S.I.G.)
NOTE: If the actual pressure are higher than shown, the
system is most likely over-charged, and charge
should be removed. If the actual pressureare
lower than shown, the system is most likely
undercharged, and charge should be added
The air conditioner is now ready for use.
PUMP DOWN
This is performed when the unit is to be
relocated or the refrigerant circuit is serviced.
Pump Down means collecting all refrigerant in the
outdoor unit without loss in refrigerant gas.
CAUTION:
Be sure to perform Pump Down procedure with the
unit cooling mode.
Bolt
Pump Down Procedure
Tubing connection
C Evaluation of the performance
Operate unit for 15~20 minutes, then check the
system refrigerant charge:
1. Measure the pressure of the gas side service
valve.
2. Measure the temperature of the intake and
discharge of air.
1. Connect a low-pressure gauge mainifold hose to the
charge port on the gas side service valve.
2. Open the gas side service valve halfway and purge
the air from the manifold hose using the refrigerant
gas.
3. Close the liquid side service valve(all the way in).
4. Turn on the unit's operating switch and start the
cooling operation.
5. When the low-pressure gauge reading becomes 1
2
to 0.5kg/cm G(14.2 to 7.1 P.S.I.G.), fully close the
gas side valve stem and then quickly turn off the
unit. At that time, Pump Down has been completed
and all refrigerant gas will have been collected in
the outdoor unit.
16
Soap water method
(1) Remove the caps from the 2-way and 3-way
valves.
(2) Remove the service-port cap from the 3-way
valves.
(3) To open the 2-way valve turn the valve stem
counterclockwise approximately 90°, wait for
about 2~3 sec, and close it.
(4) Apply a soap water or a liquid neutral detergent
on the indoor unit connection or outdoor unit
connections by a soft brush to check for
leakage of the connecting points of the piping.
(5) If bubbles come out, the pipes have leakage.
Gas side
Liquid side
3-way valve
(Close)
2-way valve
(Open)
Cap
Hexagonal wrench
C Evacuation
Connect the charge hose end described in the
preceding steps to the vacuum pump to
evacuate the tubing and indoor unit.
Confirm the "Lo" knob of the manifold valve is
open. Then, run the vacuum pump.
The operation time for evacuation varies with
tubing length and capacity of the pump. The
following table shows the time required for
evacuation.
Indoor unit
Required time for evacuation when 30 gal/h
vacuum pump is used
If tubing length is less
than 10m (33 ft)
10 min. or more
If tubing length is longer
than 10m (33 ft)
Outdoor unit
15 min. or more
When the desired vacuum is reached, close the
"Lo" knob of the manifold valve and stop the
vacuum pump.
D Finishing the job
With a service valve wrench, turn the valve stem
of liquid side valve counter-clockwise to fully
open the valve.
Turn the valve stem of gas side valve
counter-clockwise to fully open the valve.
Loosen the charge hose connected to the gas side
service port slightly to release the pressure, then
remove the hose.
Replace the flare nut and its bonnet on the gas side
service port and fasten the flare nut securely with an
adjustable wrench. This process is very important to
prevent leakage from the system.
Replace the valve caps at both gas and liquid side
service valves and fasten them tight.
This completes air purging with a vacuum pump.
The air conditioner is now ready to test run.
Manifold valve
Pressure
gauge
Lo
Hi
Open
Close
Vacuum pump
15
1
Air purging
AIR PURGING
Air and moisture remaining in the refrigerant
system have undesirable effects as indicated
below.
Pressure in the system rises.
Operating current rises.
Cooling(or heating) efficiency drops.
Moisture in the refrigerant circuit may
freeze and block capillary tubing.
Water may lead to corrosion of parts in the
refrigeration system.
Therefore, the indoor unit and tubing between
the indoor and outdoor unit must be leak tested
and evacuated to remove any noncondensables
and moisture from the system.
2
1
Do a leak test of all joints of the tubing(both
indoor and outdoor) and both gas and liquid side
service valves.
Bubbles indicate a leak. Be sure to wipe off the
soap with a clean cloth.
After the system is found to be free of leaks,
relieve the nitrogen pressure by loosening the
charge hose connector at the nitrogen cylinder.
When the system pressure is reduced to normal,
disconnect the hose from the cylinder.
Indoor unit
Air purging with vacuum
pump
A Preparation
Outdoor unit
Check that each tube(both liquid and gas
side tubes) between the indoor and
outdoor units have been properly
connected and all wiring for the test run
has been completed. Remove the service
valve caps from both the gas and the liquid
side on the outdoor unit. Note that both the
liquid and the gas side service valves on
the outdoor unit are kept closed at this
stage.
B Leak test
Manifold valve
Pressure
gauge
Lo
Hi
Connect the manifold valve(with pressure
gauges) and dry nitrogen gas cylinder to
this service port with charge hoses.
Charge hose
CAUTION
Be sure to use a manifold valve for air
purging. If it is not available, use a stop valve
for this purpose. The "Hi" knob of the manifold
valve must always be kept close.
Pressurize the system to no more than 150
P.S.I.G. with dry nitrogen gas and close the
cylinder valve when the gauge reading
reached 150 P.S.I.G. Next, test for leaks with
liquid soap.
Nitrogen gas
cylinder(in vertical
standing position)
CAUTION
To avoid nitrogen entering the refrigerant system in a
liquid state, thetop of the cylinder must be higher than its
bottom when you pressurize thesystem. Usually, the
cylinder is used in a vertical standing position.
14
CHECKING THE DRAINAGE AND FORMING THE PIPINGS
1
Checking the drainage
To remove the front panel from the indoor
A unit,
remove the front panel from the
Form the piping
2
1 A
indoor unit cabinet.
Set the air direction louvers up-and-down to
the position(horizontally) by hand.
Remove the securing screws that retain the
front panel. Pull the lower left and right
sides of the grille toward you and lift it off.
(18K, 24K, 26K Btu models: 3EA)
Form the piping by wrapping the
connecting portion of the indoor unit with
insulation material and secure it with two
kinds of vinyl tapes.
If you want to connect an additional drain
hose, the end of the drain outlet should be
routed above the ground. Secure the drain
hose appropriately.
B
In cases where the outdoor unit is
installed below the indoor unit perform
the following.
Tape the piping, drain hose and
connecting cable from down to up.
Secure the tapped piping along the exterior
wall using saddle or equivalent.
Pull the right and
the left side.
Screw
Seal small openings
around pipings with a
gum type sealer.
B To check the drainage.
Pour a glass of water on the evaporator.
Ensure the water flows through the drain
hose of the indoor unit without any leakage
and goes out the drain exit.
Taping
Drain
hose
Pipings
Connecting
cable
Trap is required to prevent water
from entering into electrical parts.
C In cases where the Outdoor unit is
installed above the Indoor unit perform
the following.
Tape the piping, and connecting cable from
down to up.
Secure the taped piping along the exterior
wall. Form a trap to prevent water entering
the room.
Fix the piping onto the wall by saddle or
equivalent.
C Drain piping
The drain hose should point downward for
easy drain flow.
Downward slope
Seal a small opening
around the pipings
with gum type sealer.
Do not make drain piping.
Accumulated
drain water
Air
Do not raise
Water
leakage
Water
leakage
Waving
Trap
Tip of drain hose
dipped in water
Water
leakage
Less than
50mm gap
Trap
Ditch
13
2
1
Connect the cable to the
outdoor unit
A
Remove the control cover from the unit by
loosening the screw.
Connect the wires to the terminals on the
control board individually.
B Secure the cable onto the control board with
the cord clamp.
C Refix the control cover to the original
position with the screw.
D
Outdoor Unit
Terminal block
Over 5mm
Connecting cable
Connecting cable
Cover Control
control
Use a recognized circuit breaker 20A (18K),
25A (24K, 26K) between the power source
and the unit. A disconnecting device to
adequately disconnect all supply lines must
be fitted.
CAUTION
After the confirmation of the above conditions, prepare the wiring as follows:
1) Never fail to have an individual power circuit specifically for the air conditioner. As for
the method of wiring, be guided by the circuit diagram posted on the inside of control
cover.
2) The screw which fasten the wiring in the casing of electrical fittings are liable to come
loose from vibrations to which the unit is subjected during the course of
transportation. Check them and make sure that they are all tightly fastened. (If they
are loose, it could cause burn-out of the wires.)
3) Specification of power source.
4) Confirm that electrical capability is sufficient.
5) See to that the starting voltage is maintained at more than 90 percent of the rated
voltage marked on the name plate.
6) Confirm that the cable thickness is as specified in the power source specification.
(Particularly note the relation between cable length and thickness. (Refer to page 11))
7) Always install an earth leakage circuit breaker in a wet or moist area.
8) The following would be caused by voltage drop.
Vibration of a magnetic switch, which will damage the contact point, fuse breaking, disturbance of the
normal function of the overload.
9) The means for disconnection from a power supply shall be incorporated in the fixed
wiring and have an air gap contact separation of at least 3mm in each active(phase)
conductors.
12
CONNECTING THE CABLE BETWEEN INDOOR UNIT AND OUTDOOR UNIT
1
Connect the cable from
Indoor to outdoor unit.
Connect the cable to the indoor unit by
connecting the wires to the terminals on the
control board individually according to the
outdoor unit connection.
CAUTION
The power cord connected to the indoor unit should
be compiled with the following specifications
(Type H05VV-F approved by HAR or SAA).
Capacity
(Btu/h)
(Ensure that the color of the wires of the
outdoor unit and the terminal No. are the same
as those of the indoor unit.)
Cooling model (1.5, 2.0 Ton)
IDU Terminal
1(L)
Cooling model (1.0 Ton)
2(N)
BLACK
1(L)
ODU Terminal
BLACK GREEN YELLOW
RED
Color of Wires
BLACK GREEN YELLOW
RED
Color of Wires
RED
Connector of
Indoor Unit
Lock the
connectors
properly
RED
G/Y
RED
Color of Wires
Color of Wires
1(L) 2(N)
BLACK
RED
BLACK
RED
1
2
BLACK GREEN YELLOW
2(N)
3
G/Y
G/Y
1.0mm2
12K
12K
18K
4
5
6
2.5mm2
NORMAL CROSS
-SECTIONAL AREA
1.0mm2
1.5mm2
2.5mm2
NORMAL
CROSS-SECTIONAL
AREA 0.75mm 2
4
BLUE BROWN
BLUE BROWN
3
NORMAL CROSS
-SECTIONAL AREA
1.5mm2
18K
24K
26K
The power connecting cable connected to the
indoor and outdoor unit should be compiled with the
following specifications
(Type H07RN-F approved by HAR or SAA).
Capacity
(Btu/h)
Connector of
Inter-connecting
cable
2(N)
Color of Wires BLACK
To be screwed
on the channel
plate of
evaporator coil.
24K
26K
1(L)
ODU Terminal
The connecting cable connected to the indoor and
outdoor unit should be compiled with the following
specifications
(Type H07RN-F approved by HAR or SAA).
Screw the
Wire on
Control Panel
Heat pump model
Terminals on the indoor unit
Color of Wires
Terminals on the outdoor unit
The length of the power supply cord should be
over 1.8m measured from the power supply cord
entry of the cabinet to the middle of the live pin
of the plug.
CAUTION
If a power plug is not to be used, provide a circuit breaker between power source and the unit as shown below.
Main power source
Air
Conditioner
Circuit Breaker
Use a circuit
breaker or time
delay fuse.
11
Bundle the piping and drain hose together by
wrapping them with cloth tape over the range
within which they fit into the rear piping housing
section.
Pipe
Connection of the
3 pipes-Outdoor
Drain hose
Vinyl tape(narrow)
Align the center of the pipings and
A sufficiently
tighten the flare nut by hand.
Wrap with
vinyl tape(wide)
H Reroute the pipings and the drain hose across
the back of the chassis.
Piping for
passage through
piping hole
I Set the pipings and the drain hose to the back of
the chassis with the tubing holder.
Hook the edge of tubing holder to tap on chassis
and push the bottom of tubing holder to be
engaged at the bottom of chassis.
B Finally, tighten the flare nut with torque
wrench until the wrench clicks.
When tightening the flare nut with torque
wrench, ensure the direction for tightening
follows the arrow on the wrench.
Capacity
(Btu/h)
18K, 24K, 26K
Pipe Size[Torque]
3/8"[4.2kg.m]
5/8"[6.6kg.m]
1/4"[1.8kg.m]
1/2"[5.5kg.m]
LIQUID
GAS
Tubing holder
1 Hook
Outdoor unit
2 Push
Gas side piping
(Bigger diameter)
J Indoor unit installation
Liquid side
piping
(Smaller
diameter)
Remove the spacer.
Ensure that the hooks are properly seated on the
installation plate by moving it left and right.
Connecting
cable
Torque wrench
Drain hose
Press the lower left and right sides of the unit against
the installation plate until the hooks engage into their
slots(clicking sound).
10
C Insert the connecting cable into the indoor unit.
Don't connect the cable to the indoor unit.
Make a small loop with the cable for easy
connection later.
Capacity
(Btu/h)
18K, 24K, 26K
D Tape the drain hose and the connecting cable.
Connecting cable
Pipe Size[Torque]
3/8"[4.2kg.m]
5/8"[6.6kg.m]
1/4"[1.8kg.m]
1/2"[5.5kg.m]
LIQUID
GAS
When extending the drain hose at the indoor unit.
install the drain pipe.
Drain pipe
Indoor unit drain hose
Adhesive
E Indoor unit installation
Hang the indoor unit from the hooks at the top of
the installation plate.
Insert the spacer etc. between the indoor unit and
the installation plate and separate the bottom of
the indoor unit from the wall.
Vinyl tape(narrow)
G Wrap the insulation material around the
connecting portion.
Overlap the connection pipe heat insulation and the
indoor unit pipe heat insulation material. Bind them
together with vinyl tape so that there is no gap.
Plastic bands Insulation material
Indoor unit
Spacer
Installation plate
8cm
F Connecting the pipings to the indoor unit and
Wrap the area which accommodates the rear
piping housing section with vinyl tape.
the drain hose to drain pipe.
Align the center of the pipings and sufficiently
tighten the flare nut by hand.
Indoor
unit pipe
Connection
pipe
Vinyl tape
(wide)
Indoor unit tubing
Flare nut
Wrap with vinyl tape
Pipe
Pipings
Vinyl tape(narrow)
Tighten the flare nut with a wrench.
Connecting cable
Spanner (fixed)
Flare nut
Connection pipe
Torque wrench
Indoor unit tubing
9
Tighten the flare nut with a wrench.
Spanner (fixed)
Flare nut
Wrap the area which accommodates the rear
piping housing section with vinyl tape.
Connection
pipe
Vinyl tape
(wide)
Indoor
unit pipe
Wrap with vinyl tape
Connection pipe
Torque wrench
Connecting cable
Indoor unit tubing
Pipe
Vinyl tape(narrow)
Capacity
(Btu/h)
18K, 24K, 26K
Pipe Size[Torque]
3/8"[4.2kg.m]
5/8"[6.6kg.m]
1/4"[1.8kg.m]
1/2"[5.5kg.m]
LIQUID
GAS
Bundle the piping and drain hose together by
wrapping them with vinyl tape over the range
within which they fit into the rear piping housing
section.
When extending the drain hose at the indoor unit,
install the drain pipe.
Wrap with vinyl tape
Pipe
Drain pipe
Vinyl tape(wide)
Drain hose
Indoor unit drain hose
Adhesive
For right rear piping
Vinyl tape(narrow)
A Route the indoor tubing and the drain hose to
F Wrap the insulation material around the
the required piping hole position.
connecting portion.
Overlap the connection pipe insulation material and
the indoor unit pipe insulation material. Bind them
together with vinyl tape so that thee is no gap.
Plastic bands Insulation material
B Insert the piping, drain hose and the connecting
cable into the piping hole.
Connecting cable
Drain pipe
8
2
Connection of piping
--Indoor
C
Preparing the indoor unit's piping and drain
hose for installation through the wall.
Remove the plastic tubing retainer (see
illustration below) and pull the tubing and
drain hose away from chassis.
Replace the plastic tubing holder in the
original position.
Tape the tubing, drain hose and the connecting
cable. Be sure that the drain hose is located at
the lowest side of the bundle. Locating at the
upper side can cause drain pan to overflow
inside the unit.
Loop
Tubing holder
Liquid side
piping
Drain hose
Gas side
piping
Connecting
cable
NOTE: If the drain hose is routed inside the room,
insulate the hose with an insulation material* so that
dripping from "sweating"(condensation) will not damage
furniture or floors.
*Foamed polyethylene or equivalent is recommended.
To remove the holder,
press the bottom of
chassis near the holder
upward and pull the tab
out of its hole.
D Indoor unit installation
CAUTION
When install, make sure
that the remaining parts
must be removed clearly
so as not to damage the
piping and drain hose,
especially power cord
and connecting cable.
Hook the indoor unit onto the upper portion of the
installation plate.(Engage the two hooks of the
rear top of the indoor unit with the upper edge of
the installation plate.) Ensure that the hooks are
properly seated on the installation plate by
moving it left and right
For left rear piping
A
Connecting
cable
Route the indoor tubing and the drain hose
in the direction of rear left.
Drain hose
Press the lower left and right sides of the unit
against the installation plate until the hooks engage
into their slots(clicking-sound).
Connecting the pipings to the indoor unit and
E drain
hose to drain pipe.
Drain hose
B
Align the center of the pipings and sufficiently
tighten the flare nut by hand.
Insert the connecting cable into the indoor
unit from the outdoor unit through the
piping hole.
Do not connect the cable to the indoor unit.
Make a small loop with the cable for easy
connection later.
Indoor unit tubing
Flare nut
Pipings
7
1
FLARING WORK AND CONNECTION OF PIPING
Flaring work
Main cause for gas leakage is due to defect in
flaring work. Carry out correct flaring work in the
following procedure.
A Cut the pipes and the cable.
Use the piping kit accessory or the pipes
purchased locally.
Measure the distance between the indoor
and the outdoor unit.
Cut the pipes a little longer than measured
distance.
Cut the cable 1.5m longer than the pipe
length.
D Flaring work
Carry out flaring work using flaring tool as shown
below.
Outside diameter
5/8
ø15.88
1/2
ø12.7
3/8
ø9.52
1/4
ø6.35
inch
mm
A
mm
0~0.5
0~0.5
0~0.5
0~1.0
Firmly hold copper pipe in a die in the dimension
shown in the table above.
Handle
Bar
Copper
pipe
90°
"A"
Bar
Yoke
Slanted Uneven Rough
Cone
Copper pipe
Clamp handle
Red arrow mark
B Burrs removal
Completely remove all burrs from the cut
cross section of pipe/tube.
Put the end of the copper tube/pipe in a
downward direction as you remove burrs in
order to avoid dropping burrs into the tubing.
Pipe
E Check
Compare the flared work with figure below.
If flare is noted to be defective, cut off the flared
section and do flaring work again.
Smooth all round
Inside is shiny without scratches.
Reamer
= Improper flaring =
Point down
Inclined Surface Cracked Uneven
damaged
thickness
Even length
all round
C Putting nut on
Remove flare nuts attached to indoor and
outdoor unit, then put them on pipe/tube
having completed burr removal.
(not possible to put them on after flaring
work)
Flare nut
Copper tube
6
3
How to fix installation plate
The wall you select should be strong and solid
enough to prevent vibration.
A
Mount the installation plate on the wall with
four type A screws. If mounting the unit on a
concrete wall, use anchor bolts.
4 Drill a hole in the wall
Drill the piping hole with a ø70mm hole core
drill. Drill the piping hole at either the right or
the left with the hole slightly slanted to the
outdoor side.
WALL
Indoor
Outdoor
Mount the installation plate horizontally by
aligning the centerline using a level.
5-7mm
Installation Plate
(0.2~0.3")
CAUTION
Type "A" screw
Marking-off line
Thread
Make sure that the drilled hole in the wall is
properly sealed (using a proper sealant, for
example cement, plaster of paris etc.) after
passing the installation pipe, drainage pipe
and the inter connecting cable.
Weight
B
Measure the wall and mark the centerline. It
is also important to use caution concerning
the location of the installation plate-routing of
the wiring to power outlets is through the
walls typically. Drilling the hole through the
wall for piping connections must be done
safely.
Usage of Drain Pan
5 (Heat
Pump)
Drain pan along with drain pipe (as
shown below) can be used to drain
the water accumulated in the outdoor
during the Heat Mode.
Outdoor Unit
Left rear piping
"D"
Right rear piping
"C"
ø70mm
Hole center
Drain Pan
Drain Pipe
5
INSTALLATION OF INDOOR, OUTDOOR UNIT
Read completely, then follow step by step.
1
Select the best location
A Indoor unit
Do not have any heat or steam near the
unit.
Select a place where there are no
obstacles in front of the unit.
Make sure that condensation drainage
can be conveniently routed away.
Do not install near a doorway.
Ensure that the space around the left and
right of the unit is more than 5cm. The
unit should be installed as high on the
wall as possible, allowing a minimum of
5cm from ceiling.
Use a stud finder to locate studs to
prevent unnecessary damage to the wall.
More than 5cm
More than 5cm
Rooftop Installations:
If the outdoor unit is installed on a roof structure, be
sure to level the unit. Ensure the roof structure and
anchoring method are adequate for the unit location.
Consult local codes regarding rooftop mounting.
2
Piping length and elevation
Capacity
(Btu/h)
Pipe Size
GAS LIQUID
5/8"
18K (60Hz)
24K Cooling
1/2"
18K (50Hz)
24K, 26K
5/8"
Cooling & Heat Pump
1/4"
1/4"
3/8"
20
3 to 5
Max.
length
A (m)
Standard
Length
(m)
3 to 5
3 to 5
Additional
Refrigerant
(g/m)
20
20
20
20
20
Outdoor unit
More than 2.3m
More than 5cm
CAUTION
A
Install the indoor unit on the wall where the height
from the floors more than 2.3 meters.
Indoor unit
B
B Outdoor unit
If an awning is built over the unit to
prevent direct sunlight or rain exposure,
make sure that heat radiation from the
condenser is not restricted.
Ensure that the space around the back
and sides is more than 10cm. The front of
the unit should have more than 70cm of
space.
Do not place animals and plants in the
path of the warm air.
Take the air conditioner weight into
account and select a place where noise
and vibration are minimum.
Select a place so that the warm air and
noise from the air conditioner do not
disturb neighbors.
Outdoor unit
A
Oil trap
Indoor unit
B
More than 60cm
More than 10cm
In case more than 5m
More than 10cm
CAUTION
More
than 60cm
More than 70cm
Capacity is based on standard length and maximum
allowance length is on the basis of reliability.
Oil trap should be installed every 5~7 meters.
4
THE FOLLOWING SHOULD BE ALWAYS OBSERVED FOR SAFETY
Be sure to read "THE FOLLOWING SHOULD BE ALWAYS OBSERVED FOR SAFETY" before installing the air
conditioner.
Be sure to observe the cautions specified here as they include important items related to safety.
The indications and meanings are as follows.
: Could lead to serious injury in particular environments when operated
incorrectly.
CAUTION
: Could lead to death, serious injury, etc.
WARNING
After reading this instructions, be sure to keep it together with the owner's manual in a handy place on the
customer's site.
WARNING
Do not install it yourself (customer).
Incorrect installation could cause injury due to fire,
electric shock, the unit falling or leakage of water.
Consult the dealer from whom you purchased the
unit or special installer.
Install the unit securely in a place which can bear
the weight of the unit.
When installed in an insufficiently strong place,
the unit could fall causing injury.
Use the specified wires to connect the indoor and
outdoor units securely and attach the wires firmly
to the terminal board connecting sections so the
stress of the wires is not applied to the sections.
Perform the installation securely referring to the
installation instruction.
Incorrect installation could cause a personal
injury due to fire, electric shock, the unit falling
or leakage of water.
Perform electrical work according to the installation
manual and be sure to use an exclusive circuit.
If the capacity of the power circuit is insufficient
or there is incomplete electrical work, it could
result in a fire or an electric shock.
Check that the refrigerant gas does not leak after
installation is completed.
Incorrect connection and fixing could cause fire.
Attach the electrical part cover to the indoor unit
and the service panel to the outdoor unit securely.
If the electrical part cover of the indoor unit and/or
the service panel of the outdoor unit are not
attached securely, it could result in a fire or
electric shock due to dust, water, etc.
Be sure to use the part provided or specified parts
for the installation work.
The use of defective parts could cause an injury
due to a fire, electric shock, the unit falling, etc.
CAUTION
Do not install the unit in a place where an
inflammable gas leaks.
Perform the drainage/piping work according
to the installation instruction.
If gas leaks and accumulates in the area
surrounding the unit, it could cause an explosion.
If there is a defect in the drainage/piping work,
water could leak from the unit and household
goods could get wet and be damaged.
3
Installation
Requirements
INSTALLATION OVERVIEW
Required Parts
Required Tools
The following should be always
observed for safety...................3
Pipes: Gas side ...........1/2", 5/8"
Liquid side
1/4", 3/8"
(Refer to page 4)
Insulation materials
Additional drain pipe
(Outer Diameter ...........15.5mm)
Flaring work and connection of
piping .........................................6
Connection of piping(Indoor)......7
For right rear piping
For left rear piping
Connection of piping(Outdoor)
..............................................10
Installation plate
Four type "A" screws
Connecting cable
Installation of indoor, outdoor
unit..............................................4
Level gauge
Screw driver
Electric drill
Hole core drill(ø70mm)
Flaring tool set
Specified torque wrenches
1.8kg.m, 4.2kg.m, 5.5kg.m, 6.6kg.m
(different depending on model No.)
(Refer to page 10)
Spanner......................Half union
Connecting the cable between
indoor unit and outdoor unit ......
..................................................11
Hexagonal wrench(4mm)
Gas-leak detector
Vacuum pump
Gauge manifold
Air purging ..............................14
A glass of water
Screw driver
Checking the drainage and
Forming the piping ................. 13
Test running ............................16
Two type "B" screws
Owner's manual
Thermometer
Holder Remote Control
INSTALLATION INSTRUCTIONS - SINGLE SPLIT WALL MOUNTED AIR CONDITIONER
Please read this instruction sheet completely before installing the product.
When the power cord is damaged, replacement work shall be performed by authorized personnel only.
Installation work must be performed in accordance with the national wiring standards by authorized
personnel only.
Installation Parts Provided
Installation parts you
must purchase
More than
20cm
Installation plate
Sleeve
Bushing-Sleeve
Putty(Gum Type Sealer)
1. Type "A" screw
2. Installation Plate
More than
5cm
(For wireless
model only)
3. Type "B" screw
4. Holder Remote Control
Bend the pipe as closely
on the wall as possible,
but be careful that it
doesn't break.
(Left and right
are identical)
Air filter
Vinyl tape (Wide)
Apply after carrying out a
drainahe test.
To carry out the drainage
test, remove the air filters
and pour water into the heat
exchanger.
Saddle
More than
60cm
More than
10cm
More than
10cm
• This illustration is for explanation purposes only.
• The indoor unit will actually face a different way.
Gas side piping
Liquid side piping
Additional drain pipe
More than 70cm
Vinyl tape (Narrow)
Connecting cable: Cooling & Heat pump: 2EA
Cooling only: 1EA
2
Installation Instructions
Please read this manual carefully before Installation.
MTNL / BSNL (Toll Free)
Prefix STD Code
LG Electronics India Pvt. Ltd.
Registered Office: Plot No. 51, Surajpur Kasna Road, Greater Noida - 201 306 (U.P.) INDIA Tel: 0120-2560900 Fax: 0120-2560957
Download PDF

advertising