LG | PQRCUDS0.ENCXLEU | LG PQRCUDS0S.ENCXLEU Owner’s Manual

Visit us at : http://www.lgservice.com
Owner's & Installation Manual
ESPAÑOL
Models: PQRCUDS0
PQRCUDS0B
PQRCUDS0S
ITALIANO
LG
Deluxe Wired Remote Controller
ENGLISH
LG
FRANÇAIS
DEUTSCH
IMPORTANT
êìëëäàâ
• Please read this installation manual completely
before installing the product.
• Installation work must be performed in
accordance with the national wiring standards
by authorized personnel only.
• Please retain this installation manual for future
reference after reading it thoroughly.
Deluxe Wired Remote Controller Owner’s & Installation Manual
TABLE OF CONTENTS
■ Safety Precautions ............................................................3~4
■ Part Description.................................................................5~6
■ Wired remote controller switch information .......................7
■ Installation Method................................................................8
■ Necessary functions before using ................................9~11
• Trial Operation........................................................................................9
• Setting the Central Control Address ..................................................10
• ESP Function ........................................................................................11
■ How to use the Mode Selection Button.......................12~16
• Cooling Operation ................................................................................12
• Heating Operation ................................................................................13
• Auto-Operation .....................................................................................14
• Dry(Dehumidification) Operation........................................................15
• Fan Operation .......................................................................................15
• Fan Speed Selection ............................................................................16
■ Sub Function .......................................................................17
• Auto Swing............................................................................................17
• Plasma...................................................................................................18
• Ventilation .............................................................................................19
• Heater ....................................................................................................19
■ Special Function..................................................................20
• Child Lock .............................................................................................20
• Vane control..........................................................................................21
• Swirl Swing ...........................................................................................22
• Room Temperature Display.................................................................23
• Easy reservation...................................................................................23
• Setting the current time .......................................................................24
• Weekday reservation ...........................................................................25
• Different Mode Operation ....................................................................26
Note) Please, refer to indoor's manual for product's detail information of subfunction
2 Deluxe Wired Remote Controller
Safety Precautions
Safety Precautions
• The installation requires expert skills, and it should be installed by the service center or other shops specialized
in the installation and recognized by our company.
• The following safety cautions are provided to prevent unexpected dangers or losses.
WARNING : If the user does not follow the mandatory items, it may result in serious injury or death.
CAUTION : If the user does not follow the mandatory items, it may cause personal injury or property
damage.
: Warning and Caution are to call the user’s attention to the possible danger. Read and follow
them carefully in order to prevent a safety accident.
: Warning and Caution are indicated in this guide and the product itself to help protect the users
from danger.
WARNING
■ Installation
Entrust installation of the
product to the service center
because improper installation
may cause fire, an electric
shock, explosion, and physical
injury.
Use the original parts in
order to prevent fire, an
electric shock, explosion,
and product breakdown.
Keep combustible and/or
inflammable materials away
from the product in order to
prevent fire or product
breakdown.
Service Center
Original Parts
Do not disassemble, repair, or
modify the product at your
discretion in order to prevent fire
or an electric shock.
Do not install the product in wet
and humid areas in order to
prevent product breakdown.
Do not expose the product to the
sun in order to prevent product
breakdown.
Owner’s & Installation Manual 3
ENGLISH
• For all the problems arising after installation by someone who has no relevant qualifications, LG will not provide
free service.
Safety Precautions
■ In-use
Do not modify or lengthen the
power cable at your discretion.
It may cause fire or an electric
shock.
Do not place a heating device
near the product. It may cause
fire.
Do not drop water on to the
product. It may cause an electric
shock or product breakdown.
Do not place something heavy on
the power cable. It may cause fire
or an electric shock.
Do not place a heavy thing on the
product. It may cause product
breakdown.
If the product was submerged
under water, ask the service
center for instruction. It may
cause fire or an electric shock
unless you do that.
ter
ice
v
Ser
Cen
CAUTION
Make sure children or senor
citizens use the product under
proper observation in order to
prevent safety accident.
Do not subject the product to
shock. It will cause product
breakdown.
Do not pick the product with a
sharp tool. It may cause
product breakdown with the
damage to its parts.
■ In-use
Do not clean the product with strong cleanser such
as solvent. Use soft clothes in order to prevent fire
or product deformation.
4 Deluxe Wired Remote Controller
Do not touch the product with a wet hand. Do not
pull the lead cable. It may cause product breakdown
or an electric shock.
Part Description
Part Description
2. LCD Screen
3. Connecting Cable and Connector
Accessory
Connecting Cable
(1EA)
Fixing Screw (2EA)
User / Installation
Manual
Installation Paper
Owner’s & Installation Manual 5
ENGLISH
1. Wired Remote Controller
Part Description
Deluxe Wired Remote Controller
11
1
12
2
3
4
5
6
7
8
9
10
13
14
15
16
17
18
19
20
1. Operation Display Panel
12. On / Off Button
2. Room Temperature Button
13. Special Function Button
3. Fan Speed Button
14. Dehumidification / Heater Button
4. Fan / Plasma / Swirl Swing Button
15. Sub Function Button
5. Automatic / Vane Control Button
16. Easy Reservation Button
6. Timer Mode Button
17. Cancel Button
7. Date Selection Button
18. Heating / Ventilation Button
8. Hour / Minute Button
19. Setting Button
9. Mode Selection Button
20. Cooling / Auto Swing / Child
Lock Button
10. On / Off Button for reservation
11. Temperature Control Button
Each function will be shown on the display panel for three second or so when the initial power is on.
The analog panel enables you to use the remote controller with a touch of your own finger without pressing any
extra button.
However, if you press more than one button at the same time, it may cause malfunction.
6 Deluxe Wired Remote Controller
Wired remote controller switch information
Wired remote controller switch information
Product selection switch
1. Cooling ONLY product
2. HEAT PUMP product
S/W
Indoor temperature sensor
selection switch
1. Use the temperature sensor on the
remote controller
2. Use the temperature sensor on the
product.
3. Use the sensor with the lower
temperature between the remote
controller and the product
1 2
Indoor temperature sensor selection
1
2
3
Ceiling height selection
switch
S/W 1
Ceiling height selection
Group control
S/W GR
S/W 2
1. Low ceiling
2. Standard ceiling
3. High ceiling
Group control switch
1. For individual control use
2. For group control use
1 2 3
1 2
* When changing the product selection switch and group control switch, the power must be reconnected to reflect
the changes.
Owner’s & Installation Manual 7
ENGLISH
Product selection
Installation Method
Installation Method
1
Put the installation paper on the place and determine the
position and height of the fixing screws of the wired remote
controller.
• Refer to the printed side of the installation paper.
The position of the fixing screws
Side of
remote Controller
3
CN-DISP IC01A
LO1K
J14
C01K
LO1D C07D
CN-M C CN-ZONE
Main frame
J15
• The product is being shipped
with the cable connected only
to the remote controller. Put
each cable to the remote
controller according to the
color match
Be careful not to alter the colors
of the remote controller
connection cables.
CN-REMO
Plug the connecting cable into
the indoor unit.
LO2K
2
Red
Yellow
Brown
Side of
Indoor Unit
Remove the installation paper before installing
the remote controller so that it can fit into the
right place.
Fixing the
remote controller
Fixing the
connecting cable
* When installing the wired remote controller, do not install it so that it is buried to the wall. (This can
cause error in the temperature sensor)
* When installing multiple wired remote controllers horizontally in one location, leave a minimum distance
apart (2cm). (This can cause error in the temperature sensor)
* Do not install the cable with a distance of 50 m or longer. (This can cause communication error.)
* When installing the cable, check whether the connector between the remote controller and the product is
installed properly. The connector will not be connected when installed in opposite sides.
❏ Supply the power after connecting wired remote controller.
When you need to change wired remote controller, switch off the main power and change it Before switch off
the main power if changed the wired remote controller , you can't use the option function of the indoor unit.
8 Deluxe Wired Remote Controller
Necessary function before using
Necessary functions before using
The trial operation is to check the installation status of the product. The temperature will not be controlled during
trial operation. Instead the product will operate in several modes such as cooling, strong wind, comp-on.
1
The trial operation is to check the installation status of
the product. The temperature will not be controlled.
Instead the product will operate in several modes such
as cooling, strong wind, comp-on.
2
If you wan to do the trial operation, press the Special
Function button and then select the trial operation
mode.
3
Then the product will begin the trial operation and the
display will be like the following picture.
4
The trial operation will continue for 18 minute or so
and the product will go into standby mode.
4
If you wan to cancel the trial operation during the
process, press the On/Off button.
* This function might not be available for Multi Product like Multi V system.
Owner’s & Installation Manual 9
ENGLISH
Trial Operation
Necessary function before using
Setting the Central-Control Address
1
Press the Special Function button.
2
Press the address setting button. Press the
temperature-increasing button to change the group
number. Press the temperature-decreasing button to
change the indoor unit number. The number of the
central control address group is "2." And the number of
the indoor unit is "5."
3
If you press the address setting button, the addressing
setting mode will be unset.
* If you connect the indoor unit to the central controller,
you should set the network address of the indoor unit
so that the central controller could recognize it.
* The central control address is composed of the group
number and the indoor-unit number.
Note : The remote controller displays 'HL' if central controller has locked the remote controller .
10 Deluxe Wired Remote Controller
Necessary function before using
ESP Function
100 unit 10 unit
1
Press the Special Function button.
2
Press the E.S.P button.
3
Set the volume of each air flow (Low, Medium, Hi) by
using the temperature control button. Press the air flow
button to select the air flow.
(The value of E.S.P could be adjusted from 1 to 225.)
(The figure on the left shows when the strong wind’s
ESP value has been set to 212.)
4
If you press the E.S.P button one more time, the E.S.P
value will be set and the setting mode will be unset.
* The E.S.P value is set at the proper value at the factory. So it is highly recommended that you should do not
change the E.S.P value at your discretion.
Owner’s & Installation Manual 11
ENGLISH
E.S.P function is setting the volume of each air flow. It is for the convenience of installation. It is recommended
that you should not use this function whild using the remote controller.
How to use the Mode Selection Button
How to use the Mode Selection Button
Cooling Operation
1
Cooling operation will begin if you press the On/Off
button.
2
Press the temperature button and set the expected
temperature lower than the current room temperature.
(18~30°C)
A click of the button will increase the expected temperature by 1°C
A click of the button will decrease the expected temperature by 1°C.
If the expected temperature is set higher than the current
room temperature, the cooling function will not begin and
just the blowing operation will continue.
3
Press the operation selection button and choose one of
the functions among blowing, automation, heating, and
dehumidification if you want another operation mode
during the operation.
4
If you press the On/Off button, the cooling operation
will stop.
What is the three-minute delay function?
The function to protect the compressor delays the output of cool air when operating instantly after
interrupting the cooling operation.
Cooling operation restarts after 3 minutes when the compressor starts to operate.
• You can choose the expected temperature from 18(C to 30(C.
• It is recommended that the ideal difference of the temperature between indoors and outdoors should be
less than 5°C.
12 Deluxe Wired Remote Controller
How to use the Mode Selection Button
Heating Operation
Press the heating button after pressing the On/Off
button of the remote controller.
2
Set the expected room temperature higher than the
current room temperature. (16~30°C)
A click of the button will increase the desired temperature by 1°C.
A click of the button will decrease the desired temperature by 1°C.
* If the expected temperature is set lower than the current
room temperature, the heating operation will not begin
and just the blowing operation will continue.
3
Press the operation selection button and choose one of
the functions among blowing, automation, heating, and
dehumidification if you want another operation mode
during the operation.
4
If you press the On/Off button, the heating operation
will stop.
What is the three-minute delay function?
It will take a time for the product to blow warm air. The delay is just to protect the compressor.
The room will be heated with warm air after three minutes when the compressor begins operation.
■ The cooling-only model will not do heating function.
Owner’s & Installation Manual 13
ENGLISH
1
How to use the Mode Selection Button
Auto-Operation
1
Press the On/Off button and then press the Automatic
Operation button.
2
When the room temperature is lower than the
expected temperature: Heating Operation.
When the room temperature is higher than the
expected temperature: Cooling temperature.
3
Press the operation selection button and choose one
of the functions among blowing, automation, heating,
and dehumidification if you want another operation
mode during the operation.
4
If you press the On/Off button, the cooling operation
will stop.
❈ The cooling-only model will show “AI” on the temperature display.
AI could be adjusted by five levels (-2, -1, 0, +1, +2).
❈ This auto-operation is not related to "Auto Change Over" function.
14 Deluxe Wired Remote Controller
How to use the Mode Selection Button
Dehumidification Operation
Dehumidification Operation: Dehumidification by lowering temperature slightly
Press the On/Off button on the remote controller.
2
Select the dehumidification function by pressing the
Mode selection button.
3
When the dehumidification is being done, ”dh” will be
shown on the display panel
4
Press the operation selection button and choose one
of the functions among blowing, automation, heating,
and dehumidification if you want another operation
mode during the operation.
If used during the rainy season or high humidity, you can have both of effective dehumidifying
and air conditioning effect.
❈ Temperature control is not available in the Dehumidification Operation.
Fan Operation
1
Press the On/Off button on the remote controller.
2
Select the Fan function by pressing the Mode selection
button.
3
When the Fan is being done, "fn" will be displayed on
the display panel.
4
Press the operation selection button and choose one
of the functions among heating, automation, cooling
and dehumidification if you want another operation
mode during the operation.
• Fan operation does not output cool air, but just the fan air.
• By giving out air that has no difference of temperature with the indoors, it allows ventilation of
the room.
❈ Temperature control is not available in the air fan operation.
Owner’s & Installation Manual 15
ENGLISH
1
How to use the Mode Selection Button
Fan Speed Selection
You can easily control the fan speed.
1
Select the proper fan speed which you want by
pressing the fan speed button on the remote controller.
• If you press the fan speed button, the strength of the
fan speed will change in the order of Low → Medium
Hi → Power.
• If the product is not compatible with the fan speed
control, it will not function as your selection.
Fan Speed Selection in Cooling Operation
Lo
Med
Hi
Po
Fan Speed Selection in Heating, Dry, Fan,
Auto-Operation
Lo
Med
Hi
• If the indoor unit is compatible with the slo fan speed, you
can adjust the air flow slow level.
16 Deluxe Wired Remote Controller
Sub Function
Sub Function
Auto Swing
1
Press the Sub function button on the remote controller.
2
Press the automatic Auto Swing button.
3
A click of Auto Swing button will turn on/off the
indicator.
* If the product is not compatible with the automatic wind direction mode, it will not operate
automatically.
Owner’s & Installation Manual 17
ENGLISH
You can control the wind direction easily.
Sub Function
Plasma
You can use the plasma function.
1
Press the Sub function button.
2
Press the Plasma button.
• A click of the Plasma button will turn on/off the indicator.
• If the product is not compatible with the Plasma function,
it will not do the Plasma function even though the
indicator is turned on.
• Plasma Function is possible when only product is
operating.
• Please press the Plasma button in Fan Mode, If you want
to operate only plasma function.
Ventilation
You can use the ventilation function.
1
Press the Sub function button of the remote controller.
2
Press the ventilation button.
• A click of the ventilation button will turn on/off the
indicator.
However, even when the remote controller that does not
have the ventilation function displays ventilation, the
actual product does not operate for ventilation.
18 Deluxe Wired Remote Controller
Sub Function
Heater
You can use the heater function.
Press the Sub function button.
2
Press the heater button.
• A click of the heater button will turn on/off the indicator.
• If the product is not compatible with the heating function,
it will not do the heating function.
Owner’s & Installation Manual 19
ENGLISH
1
Special Function
Special Function
This is a function to prevent tampering of settings by children or others.
Child Lock
You can use the child lock function.
1
Press the Special Function button of the remote
controller.
2
Press the child lock button.
• A click of the child lock button will turn on/off the indicator.
• If you press another button while adjusting child lock
function, the temperature display will show CL for three
seconds and then the operation will come back to the
original mode.
• If you want use the child lock function in standby mode,
select child lock and press the On/Off button within three
seconds. Then the standby mode will change into the
child lock mode.
• If you want to cancel the child lock function in the standby
mode, just press the child lock button.
20 Deluxe Wired Remote Controller
Special Function
Vane control
You can control the angle of the vane.
Select the Advanced Selection button on the control
panel of the remote controller.
2
Press the Vane Control button.
Press the Vane Control button one more time to control
the top and bottom vane.
3
You will see the screen shown on the left.
4
Press the Temperature Adjustment button to adjust the
two vane angles from P0 to P5.
5
Press the Vane Control button one more time to control
the remaining two vane angles.
6
Press the Vane Control button one more time to return
to the original mode.
• The vane angle that has been set
does not change even when the air
conditioner is turn off and on again
(default is P0)
Owner’s & Installation Manual 21
ENGLISH
1
Special Function
Swirl Swing
You can use the swirl swing.
1
Press the Special Function button of the remote
controller.
2
Press the swirl swing button.
• A click of the swirl swing will turn on/off the indicator.
• If the product is not compatible with the swirl swing
function, it will not do the function even though the
indicator is turned on.
Room Temperature Display
1
If you press indoor temperature button on the remote
controller, the indoor temperature displays for 5
seconds. The display goes to a previous screen after
5 seconds.
Indoor temperature display may differ according to a
Slide S/W1 setting on the remote controller.
❈ There would be some difference between actual
temperature you feel and room temperature of remote
controller , because the temperature of the position is
not uniform which the remote controller is located on.
22 Deluxe Wired Remote Controller
Special Function
Easy Reservation
Press Timer mode button on the remote controller.
2
3
Press easy reservation button.
You can change the values by pressing the
temperature control buttons. Choose a desired
reservation time.
pressing the setting button, set your easy
4 Byreservation
time
Power-on reservations can be set only when not in
operation
- You can set reservation from 1 to 24 hours
reservation can be set only when in
5 Power-off
operation
- If power-on reservation was set, it will start operating
after the set time
- If power-off reservation was set, it will stop operating
after the set time
- Excessive use of air conditioning is bad for your
health. Please set a moderate amount of time for
your reservation.
- It works wired remote controller's reservation time, if
preset time by wrieless and wired remote controller at
the same time .
Owner’s & Installation Manual 23
ENGLISH
1
Special Function
Setting the current time
24 Deluxe Wired Remote Controller
1
You can set the current time by pressing the time
display.
When the time display is selected, a window for date
and time setting shows up.
2
Press the date selection button.
If you press the date selection button, the day of the
week will flash. Then you can choose the proper day in
the order of Monday, Tuesday, Wednesday, Thursday,
Friday, Saturday, and Sunday.
3
If you press the hour/minute selection button, the hour
digits will flash so that you can adjust it by pressing the
temperature control button. If you press the
hour/minute button one more time, the minute digits
will flash. You can adjust it by pressing the temperature
control button.
4
After adjusting time, press the setting button so that the
current configuration can be saved.
Special Function
Weekday reservation
1
Press the Reservation Mode button on the control
panel of the remote controller.
2
Select the day of week to set using the Day Selection
button.
3
After selecting the day of week, select the time to turn
on the air conditioner using the Time/Minute button.
Press the Time/Minute button one more time to set the
minute using the Temperature Adjustment button and
press the set button.
4
After pressing the On/Off button decide the time to turn
off the air conditioner using the Temperature
Adjustment button. Press the Set button when
completed.
If the Off icon blinks for a while and then stops on the
time display panel, it is successfully set.
5
To set for other days of the week, press the Day button
and set the time in the same procedure. Press the
Reservation button to exit the reservation mode.
6
To cancel the Weekday reservation function, press the
Reservation mode and then Cancel.
If you see an outline box around the day of week, it
means that time to start and end have been set. When
selecting the Reservation mode, other Function button
cannot be entered.
- It works wired remote controller's reservation time, if
preset time by wrieless and wired remote controller at
the same time .
Owner’s & Installation Manual 25
ENGLISH
Weekday reservation is the function to set the time to turn on and off for each day during the week
from Monday through Sunday.
Different Mode Operation
When One outdoor unit have several indoor units,Different Mode Operation is which each indoor unit
operate different mode.
1
If one indoor unit operate heating Mode while several
indoor units are operating Cooling Mode, Outdoor
segment and Cooling segment are blinking like screen
on the left
• It means operation of cooling Mode in outdoor unit
2
If one indoor unit operate Cooling or Dehumidification
Mode while several indoor units is operating Heating
Mode, Outdoor segment and Cooling segment is
blinking
• It means operation of Heating Mode in outdoor unit.
3
When push the On/Off button, the indoor unit operate
mode automatically which other indoor unit is operating
for 5 second later.
• If the product is not compatible with the Different Mode
Operation, Screen will be displayed CH07.
• If CH07 is displayed , please change the mode.
• Different Mode Operation is not error
26 Deluxe Wired Remote Controller
P/No.: 3828A20561C
Printed in Korea
After reading this manual, keep it in a place easily accessible to the user for future reference.
Download PDF