LG | PREMTA000.ENCXIDA | LG PREMTA000.ENCXIDA Owner’s Manual

1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 1
ENGLISH
INSTALLATION/USER MANUAL
AIR
CONDITIONER
Please read this installation manual completely before installing the product.
Installation work must be performed in accordance with the national wiring standards by authorized personnel only.
Please retain this installation manual for future reference after reading it thoroughly.
Premium Wired Remote Controller
PREMTA000
P/NO : MFL69279715
Rev.00_031516
www.lg.com
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 2
TIPS FOR SAVING ENERGY
2
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Here are some tips that will help you minimize the power consumption when you use the air
conditioner. You can use your air conditioner more efficiently by referring to the instructions
below:
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
•
•
•
•
•
•
Do not cool excessively indoors. This may consume more electricity.
Block sunlight with blinds or curtains while you are operating the air conditioner.
Keep doors or windows closed tightly while you are operating the air conditioner.
Adjust the direction of the air flow vertically or horizontally to circulate indoor air.
Speed up the fan to cool or warm indoor air quickly, in a short period of time.
Clean the air filter once every 2 weeks. Dust and impurities collected in the air filter may block the
air flow or reduce the cooling / dehumidifying functions.
Always comply with the following precautions to avoid dangerous situations and ensure peak
performance of your product
! WARNING
This symbol indicates potentially hazardous situation which, if not avoided could result in death or
serious injury.
! CAUTION
This symbol indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury.
!
WARNING
Installation
• For electrical work, contact the dealer, seller, a qualified electrician, or an authorized service Center.
- Do not disassemble or repair the product. There is risk of fire, electric shock, explosion, equipment
malfunction, or injury.
• Request to the service center or installation specialty store when reinstalling the installed product.
- There is risk of fire, electric shock, explosion, equipment malfunction, or injury.
• Do not disassemble, fix, and modify products randomly.
- There is risk of fire, electric shock, explosion, equipment malfunction, or injury.
• The product shall be installed according to the national standards and local code.
• Apply totally enclosed noncombustible conduit in case of local building code requiring plenum.
• Use appropriate unit mounting procedures.
• Avoid direct sunlight.
• Avoid moist areas.
In-Use
• Do not place flammable objects close to the product.
- There is risk of fire, electric shock, explosion, equipment malfunction or injury.
For your records
Staple your receipt to this page in case you need it to prove the date of purchase or for warranty
purposes. Write the model number and the serial number here:
Model number :
Serial number :
You can find them on a label on the side of each unit.
• Do not allow product to get wet.
- There is risk of fire, electric shock, explosion, equipment malfunction or injury.
• Avoid dropping the product.
- There is risk of fire, electric shock, explosion, equipment malfunction or injury.
• If product gets wet, contact your dealer or authorized service center.
- There is risk of fire, electric shock, explosion, equipment malfunction, or injury. If the instructions
are not followed, it may cause death or severe injury of the user.
• Do not use sharp or pointed objects on product.
- There is risk of fire, electric shock, explosion, equipment malfunction or injury.
Dealer’s name :
Date of purchase :
• Do not touch or pull the lead wire with wet hands.
- There is risk of product breakdown or electric shock.
ENGLISH
TIPS FOR SAVING ENERGY
3
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 4
IMPORTANT SAFETY INSTRUCTIONS
4
CAUTION
• Do not clean using powerful detergents like solvent but use soft cloths.
There is risk of fire, electric shock, explosion, equipment malfunction or deformation.
• Do not press the screen using powerful pressure.
There is risk of product break-down or malfunction.
5
ENGLISH
!
In-use
TABLE OF CONTENTS
TABLE OF CONTENTS
2
3
TIPS FOR SAVING ENERGY
28
Heating Operation
30
Dehumidification Operation
31
Monsoon Dehumidifying Mode
IMPORTANT SAFETY INSTRUCTIONS
32
Fan Only Operation
33
Artificial Intelligence / Automatic Operation
8
PART DESCRIPTION
35
9
2 set point auto operation (North
America Only)
OPERATION SETTING –
Standard Mode
36
Override control
39
Hold
9
On/Off
40
Zone Control
10
General Cooling Operation
42 TEMPERATURE SET-
11
Power Cooling
13
Heating Operation
14
Dehumidification Operation
15
Monsoon Dehumidifying Mode
16
Fan Only Operation
17
Artificial Intelligence / Automatic Operation
19
2 set point auto operation (North
America Only)
20 TEMPERATURE SETTING
20
42
Controlling Desired Temperature
43
Check Room Temperature
44 WIND SETTING - Advanced Mode
44
Fan speed Control
45
Airflow Control
46 SUB FUNCTION SETTING
- Standard Mode
46
Up/Down Vane Angle Setting
Controlling Desired Temperature
49
Plasma Purification Setting
51
Energy-Saving Cooling Setting
53
Heater Setting
55
Fan Auto Setting
57
Robot Cleaning Setting
59
Ventilation kit Setting
61
Humidifier Setting
63
Mosquito Away
65
Himalaya Cooling
67
Comfort Saving
22 WIND SETTING - Standard Mode
22
Fan speed Control
23
Airflow Control
24 OPERATION SETTING Advanced Mode
24
TING – Advanced Mode
On/Off
25
General Cooling Operation
27
Power Cooling
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 6
6
TABLE OF CONTENTS
Ventilator
111
Time Limit Control
163
113
Alarm Popup
165 SERVICE SETTING
115
Initialization Usage Data
Summer Time Setting
165
Service Contact
166
Service number registration and change
168
Model Information
170
Remocon version information
172
Self-diagnosis for Trouble Mode
7
196
Zone Type Setting(air conditioner)
197
Zone Number Setting(air conditioner)
198
Celsius control unit setting (air conditioner)
199
Emergency Heater Setting(air conditioner)
201
Setting of Function control during
group control (air conditioner)
202
External Devices Of Indoor Unit Setting
(air conditioner)
203
Indoor unit address verification (air conditioner)
204
Setting temperature range (air conditioner)
206
Static Pressure Step Setting(air conditioner)
207
Guard timer(air conditioner)
208
Fan operation in the cooling mode and
thermal off conditions (air conditioner)
69
Air conditioner - Ventilation Control
Switching
117 FUNCTION SETTING
70
General Ventilation Operation Mode
117
71
Ventilator with DX(Direct eXchanger)
Operation Mode
Lock Setting – All Lock, On/Off Lock,
Mode Lock
118
Lock Setting – Temperature Lock
121
Filter Sign Check
123
Elevation Grill Setting
173 INSTALLATION
125
Robot Cleaning
173
Installation of Remote Controller
126
Auto Dry
175
Group Control
127
Change Temperature
177
Air conditioner and ventilation interface
128
Example of using the change temperature function
178 INSTALLER’S SETTING
129
Wireless Module AP mode
130
Zone Name Setting
178
How to enter installer setting mode
74 TIMER & PROGRAM
132
Override Set Time
179
Installer setting code table
209
74
Simple Reservation
133
Home Leave Set Temperature
182
Primary Heater control setting(air conditioner)
77
Sleep Reservation
134
Dead Band
Test Run Operation (air conditioner /
DX type ventilator)
210
Turn-On Reservation
136
Delay Time - Ventilator
183
Central control address (air conditioner
/General, DX type ventilator)
Air conditioner Fan operation interlocked with ventilation (air conditioner)
80
211
83
Turn-Off Reservation
184
Indoor unit Auto-Start setting (air conditioner)
86
Create and Edit 7-Days Pattern
ESP setting (air conditioner / Gerneral,
DX type ventilator)
212
91
7-Days Pattern Deletion
185
Occupancy Duration Time Setting (air
conditioner)
140
Time Setting
93
7-Days Pattern – Day of Week Event
Copy/Paste
Indoor temperature detection sensor
setting (air conditioner)
213
Setting for Simple Dry contact unit
142
Password Setting
187
Ceiling height selection (air conditioner)
215
Product direction (General ventilator)
94
Weekly Schedule
143
Change Password
188
Static pressure setting (air conditioner)
216
96
Yearly Schedule
145
Main Screen Display Setting
190
Express ventilation priority (General, DX
type ventilator)
98
Delete Yearly Schedule
147
LCD brightness in idle
Remote controller master / slave setting (air conditioner / Gerneral, DX type
ventilator)
217
Holiday
149
Humidification of Stand-alone Ventilation mode (General, DX type ventilator)
99
Screen Saver Timer Setting
Add Holiday
151
218
99
Schedule Initialization
Humidification Of Ventilation With
Heating Operation (DX type ventilator)
102
Delete Holiday
153
Touch Beep
219
155
Home theme
Ventilator Fan Speed Alignment (General ventilator)
72 FAN SPEED SETTING Ventilator
72
Fan speed Control
73 ADDITIONAL MODE SETTING - Ventilator
73
Fast Mode
73
Energy-Saving Mode
104 ENERGY
138 USER SETTING
138
OPTIONS
Date Setting
157
Temperature Unit Setting
104
Check Energy Usage
159
Language Setting
107
Target Energy Consumption
161
109
Operation Time Limit
Control Type Setting(North America
Only)
191
Operation master / slave setting (air
conditioner / General, DX type ventilator)
193
Dry contact mode setting (air conditioner / DX type ventilator)
194
Fan speed fixing (air conditioner / DX
type ventilator)
195
Celsius / Fahrenheit Switching (air conditioner)
ENGLISH
69 OPERATION SETTING -
TABLE OF CONTENTS
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 8
8
PART DESCRIPTION
OPERATION SETTING – Standard Mode
OPERATION SETTING – Standard Mode
On/Off
LG Premium Wired remote controller
Air conditioner and ventilator will be turned on or off.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● Press On/Off button in the screen.
- If the product is in operation, Go Back button and Home button will be illuminated.
- If the product is in stop, Go Back button's backlight and Home button's backlight will be off.
Operation
display window
and
Touch screen
Home button
Back button
Wireless
remote controller
reception part
Reset hole
Operation display window: Displays operation and setting status
Touch screen: Control of product operation and setting status
*If user presses in many places of touch screen at the same time, touch panel
can’t response
Back button: Move to the previous setting screen
Home button: Move to the default screen
Wireless reception port: Receives wireless remote controller signal
- This feature may be disabled depending on the indoor products.
Reset button: Reset wired remote controller
- If you press the reset hole with a sharp object, the power will be reset.
*If you press it too hard, it may cause failure.
Accessories
Connecting cable
(1 EA)
Remote controller
fixing screws (4 EA)
User/Installation Manual
● If you press On/Off button during the use, product operation will stop.
ENGLISH
PART DESCRIPTION
9
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 10
10 OPERATION SETTING – Standard Mode
OPERATION SETTING – Standard Mode
Power Cooling
Maintains proper cooling comfort
It performs a strong cooling in a short period of time.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● During the operation of the product, press the mode button on the screen.
- The operation mode selection screen is displayed.
● During the operation of the product, press the fan speed button on the screen.
- The fan speed selection screen is displayed.
● In operation mode selection screen, press the ‘Cool’ button.
- The initial temperature set for cooling operation is 18°C (64°F).
● During the cooling operation, if you press fan speed ‘+’ button, power cooling is performed
after fan speed ‘HIGH’.
h For some indoor units products, according to whether there is a wind amount function, power
cooling is performed after fan speed ‘POWER’.
● During the cooling operation, if you press fan speed ‘-’ button, power cooling is performed
after fan speed ‘AUTO’.
h For some indoor units products, according to whether there is a fan speed function, power
cooling is performed after fan speed ‘LOW’ or ‘SLOW’.
● If you press On/Off button during the use, product operation will stop.
ENGLISH
General Cooling Operation
11
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 12
12 OPERATION SETTING – Standard Mode
OPERATION SETTING – Standard Mode 13
Heating Operation
Provides warm air to the space.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● During the operation of the product, press the mode button on the screen.
- The operation mode selection screen is displayed.
● If you operate the fan speed control button during the usage, power cooling is turned off and
fan speed and set temperature returns to the setting before the power cooling.
What is power cooling?
• Desired temperature: 18°C (64°F)
• Fan Speed: ‘POWER’
• Fan direction: fixed to cooling operation position
h Some products do not have the power cooling function.
These operations quickly decrease
the indoor temperature.
● In operation mode selection screen, press the ‘Heat’ button.
- The initial temperature set for Heating operation is 30°C (86°F).
- Depending on the indoor unit type, the desired temperature can be controlled in increments
1°C or 0.5°C(2°F or 1°F)
● If you press On/Off button during the use, product operation will stop.
ENGLISH
● If you press ‘Go Back’, or ‘Home’ button, it will exit from the setting menu.
- If there is no button input for about 60 seconds, it automatically exits from the setting menu.
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 14
14 OPERATION SETTING – Standard Mode
OPERATION SETTING – Standard Mode 15
Monsoon Dehumidifying Mode
Removes moisture from the air.
This is monsoon region-specific dehumidification function.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● During the operation of the product, press the mode button on the screen.
- It moves to the operation mode selection screen.
● During the operation of the product, press the mode button on the screen.
- It moves to the operation mode selection screen.
● In operation mode selection screen, press the ‘Dry’ button.
- Dehumidification operation’s initial fan speed is ‘LOW’.
- Desired temperature setting is disabled when the dehumidifying operation.
● If you press On/Off button during the use, product operation will stop.
! NOTE
You can effectively remove moisture and perform cooling operation at the same time if you
use this function during rainy season or when the humidity is high.
● In operation mode selection screen, press the ‘M’Dry’ button.
- Dehumidification operation’s initial fan speed is ‘LOW’.
- Desired temperature setting is disabled when the Monsoon dehumidifying operation.
● If you press On/Off button during the use, product operation will stop.
! NOTE
Using this function in the rainy season or high humidity, you can operate simultaneously dehumidifier and cooling mode to remove humidity effectively.
ENGLISH
Dehumidification Operation
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 16
16 OPERATION SETTING – Standard Mode
OPERATION SETTING – Standard Mode
Artificial Intelligence / Automatic Operation
Only fan will circulate air.
Operation provides heating and cooling to satisfy space requirements.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● During the operation of the product, press the mode button on the screen.
- It moves to the operation mode selection screen.
● During the operation of the product, press the mode button on the screen.
- It moves to the operation mode selection screen.
● In operation mode selection screen, press the ‘Fan’ button.
● If you press On/Off button during the use, product operation will stop.
! NOTE
It only circulates indoor air
● In operation mode selection screen, press the ‘AUTO’ button.
ENGLISH
Fan Only Operation
17
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 18
18 OPERATION SETTING – Standard Mode
OPERATION SETTING – Standard Mode 19
2 set point auto operation (North America Only)
The indoor unit automatically manages room temperature with heating and cooling with extended
setting temperature ranges.
2 set point auto mode can operate in 2 set point control mode.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● During the operation of the indoor unit, press the mode button on the screen.
- It moves to the operation mode selection screen.
● If it is cooling only model, you can control the stages from ‘hot’ to ‘cold’ with values of ‘-2’ to
‘2’ based on ‘0’.
2 : cold
1 : a little cold
0 : adequate
-1 : a little hot
-2 : hot
ex) If you feel cold, select "2".
If you feel a little cold, select "1".
If you want to keep the current state to select "0".
If you feel a little quite warm and select "-1".
If you feel quite warm and select "2".
● If you press On/Off button during use, product operation will stop.
● In operation mode selection screen, press the ‘AUTO’ button.
- "AUTO" when the operation mode is selected, desired temperature is indicated cooling and
heating temperature is desired.
- "COOL" operation mode when selected,displays only the desired cooling temperature (cooling
only the desired temperature control available)
- "HEAT" only when the operation mode selection, Heating desired temperature is displayed
(only heating temperature control can hope)
ENGLISH
● If it is cooling/heating model, you can control the desired temperature.
- Indoor temperature is displayed on the remote controller default screen.(As below the picture)
- According to the indoor unit type, the desired temperature can be controlled in the units of
1°C or 0.5°C(2°F or 1°F)
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 20
20 TEMPERATURE SETTING - Standard Mode
Controlling Desired Temperature
● During the indoor unit operation, press the temperature button on the screen.
- It moves to the temperature selection screen.
● Press the remote controller screen’s temperature setting button to set the desired temperature.
- In cooling, heating, and artificial intelligence And 2setpoint auto mode, you can control the desired temperature.
During the cooling operation
• If the desired temperature is higher than the indoor temperature, cooling is not performed.
• Set the desired temperature below the indoor temperature.
During the heating operation
• If the desired temperature is lower than the indoor temperature, heating is not performed.
• Set the desired temperature higher than the indoor temperature.
! NOTE
According to Control type setting value
• 1Set points
- You can select the desired temperature from 18 °C~30 °C(64~86 °F) for cooling operation and 16 °C~30 °C(60~86 °F) for heating operation.
• 2Set points
- You can select the desired temperature from 18 °C ~ 30 °C(64~86 °F) for cooling operation and 16 °C~30 °C(60~86 °F) for heating operation.
* A temperature area of extended range can be selected through desired temperature
range setting option.
- Cooling : 16~37.5 °C (64~99 °F) / Heating : 4~30 °C (40~86 °F)
• The temperature difference between the indoor temperature and the outdoor temperature
is recommended to be 5 °C.(86 °F)
ENGLISH
TEMPERATURE SETTING - Standard Mode
TEMPERATURE SETTING - Standard Mode 21
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 22
22 WIND SETTING - Standard Mode
Airflow Control
Fan speed Control
● During the indoor unit operation, press the screen’s ‘Air flow’ button.
- It moves to the direction of air flow selection screen.
● During the indoor unit operation, press the fan speed button on the screen.
- It moves to the fan speed selection screen.
● Press the fan speed button to set the desired fan speed.
- Every time you press the fan speed button
You can select the fan speed in the order of ‘SLOW’ → ‘LOW’ → ‘MED’ → ‘HIGH’ →
‘POWER’ → ‘AUTO’.
- Depending on the product function, some fan speed may not be selected.
● In the airflow selection screen, press the button in the desired air flow direction.
- Some Air Flow options may not be available due to the of indoor unit selected.
ENGLISH
WIND SETTING - Standard Mode
WIND SETTING - Standard Mode 23
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 24
24 OPERATION SETTING - Advanced Mode
General Cooling Operation
Maintains proper cooling comfort.
On/Off
Air conditioner and ventilator will be turned on or off.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● During the operation of the product, press the mode button on the screen.
- The operation mode selection screen is displayed.
● Press On/Off button in the screen.
- If the product is in operation, Go Back button and Home button will be illuminated.
- If the product is in stop, Go Back button's backlight and Home button's backlight will be off.
● In operation mode selection screen, press the ‘Cool’ button.
- The initial temperature set for cooling operation is 18°C (64°F).
● If you press On/Off button during the use, product operation will stop.
ENGLISH
OPERATION SETTING - Advanced Mode
OPERATION SETTING - Advanced Mode 25
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 26
26 OPERATION SETTING - Advanced Mode
ENGLISH
● Press the temperature control button to adjust the desired Indoor temperature.
- Indoor temperature is displayed on the remote controller default screen.(As below the picture)
- Depending on the indoor unit type, the desired temperature can be controlled in increments
1°C or 0.5°C(2°F or 1°F)
OPERATION SETTING - Advanced Mode 27
Power Cooling
It performs a strong cooling in a short period of time.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● During the cooling operation, if you press fan speed ‘▲’ button, power cooling is performed
after fan speed ‘HIGH’.
h For some indoor units products, according to whether there is a wind amount function,
power cooling is performed after fan speed ‘POWER’.
● During the cooling operation, if you press fan speed ‘▼’ button, power cooling is performed
after fan speed ‘AUTO’.
h For some indoor units products, according to whether there is a fan speed function, power
cooling is performed after fan speed ‘LOW’ or ‘SLOW’.
h If the desired temperature is set higher thermal cooling does not turn on and only the fan will
operate.
● If you press On/Off button during the use, product operation will stop.
What is a 3 minute delay function?
If the indoor unit is operated right after stopping the cooling, no thermal cooling is allowed.
This function protects the compressor from malfunctioning. Compressor starts 3 minutes
after and the fan starts.
! NOTE
• Setting temperature range :
Option 1. 64~86 °F (18~30 °C) (default setting)
Option 2. 64~99 °F (18~37.5 °C)
Option 3. 50~99 °F (10~37.5 °C) (if connecting to indoor unit with 2set point function)
• The difference between the indoor temperature and the outdoor temperature is recommended to be 5 °C.
● If you operate the fan speed control button during the usage, power cooling is turned off and
fan speed and set temperature returns to the setting before the power cooling.
What is power cooling?
• Desired temperature: 18°C (64°F)
• Fan Speed: ‘POWER’
• Fan direction: fixed to cooling operation position
h Some products do not have the power cooling function.
These operations quickly decrease
the indoor temperature.
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 28
28 OPERATION SETTING - Advanced Mode
Provides warm air to the space.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● Press the temperature control button to set the desired temperature higher than the indoor
temperature.
- Indoor temperature is displayed on the remote controller default screen.(As below the picture)
- According to the indoor unit type, the desired temperature can be controlled in the units of
1°C or 0.5°C(2°F or 1°F)
● During the operation of the product, press the mode button on the screen.
- It moves to the operation mode selection screen.
h If the desired temperature is set lower than the indoor temperature, heating mode is disabled.
● Pressing the On/Off button during the use, product operation will stop.
● In operation mode selection screen, press the ‘Heat’ button.
- The heating operation’s initial set temperature is 30°C (86°F).
- Depending on the indoor unit type, the desired temperature can be controlled in increments
1°C or 0.5°C(2°F or 1°F)
! NOTE
• Setting temperature range :
Option 1. 60~86 °F (16~30 °C) (default setting)
Option 2. 40~86 °F (4~30 °C)
Option 3. 40~90 °F (10~32 °C) (if connecting to indoor unit with 2set point function)
• For cooling-only model can not be selected heating.
ENGLISH
Heating Operation
OPERATION SETTING - Advanced Mode 29
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 30
30 OPERATION SETTING - Advanced Mode
OPERATION SETTING - Advanced Mode 31
Monsoon Dehumidifying Mode
Removes moisture from the air.
This is monsoon region-specific dehumidification function.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● During the operation of the product, press the mode button on the screen.
- It moves to the operation mode selection screen.
● During the operation of the product, press the mode button on the screen.
- It moves to the operation mode selection screen.
● In operation mode selection screen, press the ‘Dry’ button.
- The dehumidification operation’s initial fan speed is ‘LOW’.
- Desired temperature setting is disabled when the dehumidifying operation.
● In operation mode selection screen, press the ‘M’Dry’ button.
- Dehumidification operation’s initial fan speed is ‘LOW’.
- Desired temperature setting is disabled when the Monsoon dehumidifying operation.
● If you press On/Off button during the use, product operation will stop.
● If you press On/Off button during the use, product operation will stop.
! NOTE
You can effectively remove moisture and perform cooling operation at the same time if you
use this function during rainy season or when the humidity is high.
! NOTE
Using this function in the rainy season or high humidity, you can operate simultaneously dehumidifier and cooling mode to remove humidity effectively.
ENGLISH
Dehumidification Operation
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 32
32 OPERATION SETTING - Advanced Mode
OPERATION SETTING - Advanced Mode 33
Artificial Intelligence / Automatic Operation
Only fan will circulate air.
Operation provides heating and cooling to satisfy space requirements.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● During the operation of the product, press the mode button on the screen.
- It moves to the operation mode selection screen.
● During the operation of the product, press the mode button on the screen.
- It moves to the operation mode selection screen.
● In operation mode selection screen, press the ‘Fan’ button.
● If you press On/Off button during the use, product operation will stop.
! NOTE
It only circulates indoor air
● In operation mode selection screen, press the ‘AUTO’ button.
ENGLISH
Fan Only Operation
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 34
34 OPERATION SETTING - Advanced Mode
OPERATION SETTING - Advanced Mode 35
2 set point auto operation (North America Only)
The indoor unit automatically manages room temperature with heating and cooling with extended
setting temperature ranges.
2 set point auto mode can operate in 2 set point control mode.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● During the operation of the indoor unit, press the mode button on the screen.
- It moves to the operation mode selection screen.
● If it is cooling only model, you can control the stages from ‘hot’ to ‘cold’ with values of ‘-2’ to
‘2’ based on ‘0’.
2 : cold
1 : a little cold
0 : adequate
-1 : a little hot
-2 : hot
ex) If you feel cold, select "2".
If you feel a little cold, select "1".
If you want to keep the current state to select "0".
If you feel a little quite warm and select "-1".
If you feel quite warm and select "2".
● If you press On/Off button during use, product operation will stop.
! NOTE
If it does not work as desired, select another operation mode.
● In operation mode selection screen, press the ‘AUTO’ button.
- "AUTO" when the operation mode is selected, desired temperature is indicated cooling and
heating temperature is desired.
- "COOL" operation mode when selected,displays only the desired cooling temperature (cooling only the desired temperature control available)
- "HEAT" only when the operation mode selection, Heating desired temperature is displayed
(only heating temperature control can hope)
ENGLISH
● If it is cooling/heating model, you can control the desired temperature.
- Indoor temperature is displayed on the remote controller default screen.(As below the picture)
- According to the indoor unit type, the desired temperature can be controlled in the units of
1°C or 0.5°C(2°F or 1°F)
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 36
36 OPERATION SETTING - Advanced Mode
OPERATION SETTING - Advanced Mode 37
ENGLISH
Override control
The wired remote controller manages indoor unit status based on programmed control events.
User can set timer option at override function and return to original schedule event.
The ability to switch temporarily to the current occupancy status Override function.
- If the current "occupied" state, the transition to the "absence" status when "Override" action.
- If you are a "member" status, "Override" switch to "occupied" state during operation.
- Changes to the current reservation status before the close time and basically, (Find based on
occupancy status will be changed by the "Override".).
- Please refer to "Note" for other details.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● Press the Program button on the screen.
- It moves to schedule operation mode selection screen.
! NOTE
• It revert to default operation setting if Thermostat doesn't have last occupied schedule in
unoccupied override.
- default operation setting: Auto operation mode / set temperature : 86 °F(30 °C)(cool),
60 °F(16 °C)(heat)
• It revert to set back operation setting if Thermostat doesn't have last unoccupied schedule
in occupied override.
- set back operation setting : Auto operation mode / set back setting temperature: function
setting – set back temperature.
• It can be canceled, if Thermostat receive command from other controller.
• When changes occur in the setting by a daytime reservation operation, the schedule override mode gets deactivated.
Home leave (Unoccupied Mode)
The "Home Leave " function enables proper operation of indoor unit when a space is left for a period of time.
This feature can only be used when Control type setting is set to the 2 setpoint control mode"
● In schedule operation mode selection screen, press the ‘Override’ button.
- Press the Override button "Override" menu will be displayed for setting the end time.
- You can default value set ‘Override time’ by ‘Function setting – Override set time’
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● Press the home leave button on the screen.
Change to ‘home leave set temperature’ setting value.
- Home leave operation setting : Setting / Function / Home Leave Set Temperature.
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 38
38 OPERATION SETTING - Advanced Mode
Hold
It is a function that holds the current mode of operation.
If it is on hold, weekly or yearly or holiday schedule cannot be operation.
● Press the hold button on the screen.
! NOTE
• You can’t change setting in home leave mode except cancel the set back mode.
- lock popup is displayed on the window.
• It can be canceled ,if remote controller receive command from other controller.
• When commands are received by other controllers, the home leave mode gets deactivated.
• When the home leave mode is deactivated, the following takes place.
- The set points shall go to the current schedule set points.
- If there are no weekly schedule, the set point shall go to the last set points before the
home leave operation.
- If there are no set point before the setback operation, the set points will go to the default
if the values have not been adjusted.
- Default setting will be auto. (heat 60 °F(16 °C), cool 86 °F(30 °C))
● Touch panel is locked until you release the “Hold" mode while driving in the “Hold" mode.
! NOTE
You can You can’t change setting in ‘Hold’ except cancel the ‘Hold’
• It can be canceled ,if Thermostat receive command from other controller.
• When commands are received by other controllers, the Hold mode gets deactivated.
ENGLISH
● Touch panel is locked until you release the "Home Leave" mode.
OPERATION SETTING - Advanced Mode 39
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 40
40 OPERATION SETTING - Advanced Mode
A function to control zone with duct type indoor units.
Wired Remote controller can control maximum 8 zones.
● During the product operation, press the screen’s ‘Zone’ button.
- It moves to the direction of Zone open / close screen.
● Select zone button that you want to control.
● If you press ‘Go Back’ or ‘Home’ button, it will exit from the setting menu.
! NOTE
according to installation setting value
• If no function is supported
- This entry can not function.
• old type
- Zone control is currently only available to monitor.
• new type(4zone or 8Zone)
- Any number of zones is installed is displayed on the screen can be controlled.
ENGLISH
Zone Control
OPERATION SETTING - Advanced Mode 41
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 42
42 TEMPERATURE SETTING – Advanced Mode
Check Room Temperature
Controlling Desired Temperature
● Press the remote controller screen’s temperature setting button to set the desired temperature.
- In cooling, heating, and artificial intelligence And 2setpoint auto mode, you can control the desired temperature.
During the cooling operation
• If the desired temperature is higher than the indoor temperature, cooling is not performed.
• Set the desired temperature below the indoor temperature.
During the heating operation
• If the desired temperature is lower than the indoor temperature, heating is not performed.
• Set the desired temperature higher than the indoor temperature.
! NOTE
According to Control type setting value
• 1Set points
- You can select the desired temperature from 18 °C~30 °C(64~86 °F) for cooling operation and 16 °C~30 °C(60~86 °F) for heating operation.
• 2Set points
- You can select the desired temperature from 18 °C ~ 30 °C(64~86 °F) for cooling operation and 16 °C~30 °C(60~86 °F) for heating operation.
* A temperature area of extended range can be selected through desired temperature
range setting option.
- Cooling : 16~37.5 °C (64~99 °F) / Heating : 4~30 °C (40~86 °F)
• The temperature difference between the indoor temperature and the outdoor temperature
is recommended to be 5 °C.(86 °F)
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● On the remote controller main screen, you can check the room temperature.
! NOTE
The temperature distribution in the remote controller installation space is not uniform, so
there can be a little difference between the temperature you actually feel and the remote
controller’s room temperature display
According to Control type setting value
• 1Set points
Fahrenheit: 34~99 °F
- below 34 °F: display ‘LO’
- over 99 °F: display ‘HI’
Celsius: 0.5~39.5 °C
- below 0.5 °C: display ‘LO’
- over 39.5 °C: display ‘HI’
• 2Set points
- Room temperature display range
Fahrenheit: 52~99 °F
- below 52 °F: display ‘LO’
- over 99 °F: display ‘HI’
Celsius: 10.5~39.5 °C
- below 10.5 °C: display ‘LO’
- over 39.5 °C: display ‘HI’
- For indoor temperature below 50 °F (10 °C), the value perceived by the Thermostat(with
cable) is displayed.
• Because of location of Temperature sensing, the real room temperature and
the this displayed value can be different.
ENGLISH
TEMPERATURE SETTING – Advanced Mode
TEMPERATURE SETTING – Advanced Mode 43
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 44
44 WIND SETTING - Advanced Mode
ENGLISH
WIND SETTING - Advanced Mode
WIND SETTING - Advanced Mode 45
Airflow Control
Fan speed Control
● During the indoor unit operation, press the screen’s ‘Air flow’ button.
- It moves to the direction of air flow selection screen.
● Press the fan speed button to set the desired fan speed.
- Every time you press the fan speed button
You can select the fan speed in the order of ‘SLOW’ → ‘LOW’ → ‘MED’ → ‘HIGH’ →
‘POWER’ → ‘AUTO’.
- Depending on the product function, some fan speed may not be selected.
● In the airflow selection screen, press the button in the desired air flow direction.
- Some Air Flow options may not be available due to the of indoor unit selected.
Figure
Description
Automatically changes the airflow to up and down.
Automatically changes the airflow to left and right.
If it is connected to a indoor unit with 4 vanes exits, Air moves by
crossing over and swinging 1,3 and 2,4 vanes.
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 46
46 SUB FUNCTION SETTING
Up/Down Vane Angle Setting
● In Vane Angle (Up/Down) Setting screen, press the button of the vane to control the air flow angle.
- Up and down button and check the moving vane.
- To set the angles of all the vanes at the same time, select ‘All’ button.
● During the indoor unit operation, press screen’s ‘additional function menu‘ button.
- It moves to additional function selection screen.
● Press ‘▲’ and ‘▼’ button to select the vane angle of the selected one.
- Vane angles of movement are offered 5 stages or 6 stages according to each indoor unit.
- To reset to the initial factory default setting state, press ‘Initialize’ button.
- "Initialize" is selected, and select all the vanes are fixed to the initial value (vane angle 3)
● In the setting menu list, press ‘Vane Angle(Up/Down)’
- It moves to Vane Angle (Up/Down) Setting screen.
ENGLISH
SUB FUNCTION SETTING
SUB FUNCTION SETTING 47
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 48
48 SUB FUNCTION SETTING
SUB FUNCTION SETTING 49
Plasma Purification Setting
● Set the vane angles of the remaining vanes using the same procedure as above.
- Depending on the model of your indoor unit, you may only have 1 or 2 vane settings that can
be applied (i.e., 1-way or 2-way cassettes).
● In Additional Function Setting screen, press ‘Plasma Purification’, ‘OFF/ON’ button to activate
or turn off the desired function.
● If you press ‘Back’, ‘Go Back’, or ‘Home’ button, it will exit from the setting menu.
- If there is no button input for about 60 seconds, it automatically exits from the setting menu.
Improves indoor air quality
● During the product operation, press the screen’s ‘additional function menu’ button.
- It moves to additional function selection screen.
ENGLISH
● Press ‘Save’ button to save the vane angle setting.
- If you exit without pressing the Save button, changed value will not be applied.
- When you press the Save button, only the values currently displayed on the screen will be applied. Example) Select vane 1 → Change angle → Save → Select vane 3 → Save
- Verify by sight that the new vane angle setting has been applied. If the vane angle stays at
the original (pre-setting change) angle, your changes were not saved through the screen display.
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 50
50 SUB FUNCTION SETTING
Energy-Saving Cooling Setting
Energy-Saving cooling function enhances the comfort of the user and to improves the EnergySaving performance by controlling the desired temperature during the cooling operation.
This function is only available during the cooling operation.
● During the indoor unit operation, press “Energy Saving” button at the top right of the screen.
- The Energy-Saving cooling is set.
● The set additional operation symbol is displayed at the top right of the remote controller main
screen.
● The set additional operation is displayed at the top right of the main screen.
- If you press ‘Energy Saving’ button one more time, it will be turned off.
● You can also set or turn off the Energy-Saving cooling through the additional operation menu.
● During the indoor unit operation, press the screen’s ‘additional function menu’ button.
- It moves to the additional function selection screen.
! NOTE
• Plasma Purification is an additional function, and it may not be displayed or performed in
some indoor unit models.
• Air cleaning function can only work when indoor unit is in operation.
• If you want to operate purification only, set the plasma purification in fan mode.
ENGLISH
● If you press ‘Go Back’ or ‘Home’ button, it will exit from the setting menu.
- If no buttons are pressed within 60 seconds after setting functions, it automatically exits from
the setting menu.
SUB FUNCTION SETTING 51
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 52
52 SUB FUNCTION SETTING
Heater Setting
It is the function to reinforce the heating performance by turning on the electric heater during the
heating operation. It can be set only during heating operation.
● During the indoor unit operation, press the screen’s ‘additional function menu’ button.
- It moves to additional function selection screen.
● If you press ‘Go Back’ or ‘Home’ button, it will exit from the setting menu.
- If no buttons are pressed for 60 seconds, it automatically exits from the setting menu.
● In additional function setting screen, press ‘Electric Heater’ category’s ‘OFF/ON’ button to set
or turn off the desired state.
● The set additional operation is displayed at the top right of the main screen.
● If you press ‘Go Back’ or ‘Home’ button, it will exit from the setting menu.
- If no buttons are pressed for 60 seconds, it automatically exits from the setting menu.
! NOTE
• You can set the Energy-Saving function only during the cooling operation.
• Energy-Saving function may not work in some indoor unit products.
ENGLISH
● In additional function setting screen, press ‘Energy Saving’ category’s ‘OFF/ON’ button to set
or turn off the desired state.
SUB FUNCTION SETTING 53
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 54
54 SUB FUNCTION SETTING
Fan Auto Setting
Select fan operation after performing thermal control of indoor units.
If set to 'ON', fan operation keeps on after thermal operation of indoor units.
● During the indoor unit operation, press the screen’s ‘additional function menu’ button.
- It moves to additional function selection screen.
! NOTE
Heater function may not work in some indoor unit products.
● In additional function setting screen, press ‘Fan Auto’ category’s ‘OFF/ON’ button to set or
turn off the desired state.
● If you press ‘Go Back’ or ‘Home’ button, it will exit from the setting mode.
- If there is no button input for about 60 seconds, it automatically exits from the setting mode.
ENGLISH
● The set additional operation is displayed at the top right of the default screen.
SUB FUNCTION SETTING 55
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 56
56 SUB FUNCTION SETTING
Robot Cleaning Setting
The robot cleaning function is a function to automatically clean the filter with the cleaner installed
in the product after using the air conditioner for certain time period.
It can be set 30 seconds after stopping the operation.
● During the indoor unit operation, press the screen’s ‘additional function menu’ button.
- It moves to additional function selection screen.
! NOTE
Fan auto function may not work in some indoor unit products.
● In additional function setting screen, press the ‘Robot Cleaning’, ‘OFF/ON’ button to set or turn
off the desired state.
● If you press ‘Go Back’ or ‘Home’ button, it will exit from the setting menu.
- If no buttons are pressed for 60 seconds, it automatically exits from the setting menu.
ENGLISH
● The set additional operation is displayed at the top right of the default screen.
SUB FUNCTION SETTING 57
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 58
58 SUB FUNCTION SETTING
Ventilation kit Setting
Function enables operation of an optional ventilation kit with indoor units
● During the indoor unit operation, press the screen’s ‘additional function menu’ button.
- It moves to additional function selection screen.
! NOTE
Robot cleaning setting function may not work ins soe indoor unit products.
● In additional function setting screen, press ‘Ventilation’ category’s ‘OFF/ON’ button to set or
turn off the desired state.
● If you press ‘Go Back’ or ‘Home’ button, it will exit from the setting menu.
- If no buttons are pressed for 60 seconds after the setting, it will automatically exit from the
setting menu.
ENGLISH
● The set additional operation is displayed at the top right of the default screen.
SUB FUNCTION SETTING 59
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 60
60 SUB FUNCTION SETTING
Humidifier Setting
Function enables a humidifier if one is installed to maintain space comfort.
● During the product operation, press the screen’s ‘additional function menu’ button.
- It moves to additional function selection screen.
! NOTE
Ventilation kit control function may not work in some indoor unit products.
● In additional function setting screen, press ‘Humidifier’, ‘OFF/ON’ button to set or turn off the
desired state.
● If you press ‘Go Back’ or ‘Home’ button, it will exit from the setting menu.
- If no buttons are pressed for 60 seconds it automatically exits from the setting menu.
ENGLISH
● The set additional operation is displayed at the top right of the default screen.
SUB FUNCTION SETTING 61
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 62
62 SUB FUNCTION SETTING
Mosquito Away
Mosquito Away is a device to radiate frequency which mosquitoes don’t like.
● During the indoor unit operation, press the screen’s ‘additional function menu’ button.
- It moves to additional function selection screen.
! NOTE
Humidification function may not work in some indoor unit products.
● In additional function setting screen, press the ‘Mosquito Away’, ‘OFF/ON’ button to set or
turn off the desired state.
● If you press ‘Go Back’ or ‘Home’ button, it will exit from the setting menu.
- If no buttons are pressed for 60 seconds after the setting, it will automatically exit from the
setting menu.
ENGLISH
● The set additional operation is displayed at the top right of the default screen.
SUB FUNCTION SETTING 63
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 64
64 SUB FUNCTION SETTING
Himalaya Cooling
Mosquito Away is a device to radiate frequency which mosquitoes don’t like.
● During the indoor unit operation, press the screen’s ‘additional function menu’ button.
- It moves to additional function selection screen.
● In additional function setting screen, press the ‘Himalaya Cooling’, ‘OFF/ON’ button to set or
turn off the desired state.
● If you press ‘Go Back’ or ‘Home’ button, it will exit from the setting menu.
- If no buttons are pressed for 60 seconds after the setting, it will automatically exit from the
setting menu.
ENGLISH
● The set additional operation is displayed at the top right of the default screen.
SUB FUNCTION SETTING 65
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 66
66 SUB FUNCTION SETTING
Comfort Saving
Only products with Comfort Saving function can use this.
● During the indoor unit operation, press the screen’s ‘additional function menu’ button.
- It moves to additional function selection screen.
● In additional function setting screen, press the ‘Comfort Saving’, ‘OFF/ON’ button to set or
turn off the desired state.
● If you press ‘Go Back’ or ‘Home’ button, it will exit from the setting menu.
- If no buttons are pressed for 60 seconds after the setting, it will automatically exit from the
setting menu.
ENGLISH
● The set additional operation is displayed at the top right of the default screen.
SUB FUNCTION SETTING 67
1.MFL69279715,영영 2016. 3. 15. 영영 10:44 Page 68
68 SUB FUNCTION SETTING
OPERATION SETTING - Ventilator
Air conditioner - Ventilation Control Switching
This function is only used when air conditioner and ventilator are connected to one remote controller.
The function operates to use thermal cooling along with ventilation to provide space comfort.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● During the product operation, press the ‘ERV’ tab.
- It switches from the air conditioner mode to the ventilation mode.
● How to switch to the air conditioner mode
- Automatic switching: If no buttons are pressed for 15 seconds or longer in ventilation mode,
it automatically switches to the air conditioner control/monitoring interface.
- Manual switching: If you press the air conditioner Tab in ERV interface, it manually switches.
ENGLISH
● The set additional operation is displayed at the top right of the default screen.
OPERATION SETTING - VENTILATION 69
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 70
70 OPERATION SETTING - VENTILATION
OPERATION SETTING - VENTILATION
Ventilator with DX(Direct eXchanger) Operation Mode
You can select the ventilation mode when it is connected to a ventilation product.
It uses the heat exchanger inside the ventilation product to perform the ventilation operation
function at the same time of cooling or heating operation.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● Press remote controller screen 1 time to turn on.
- If remote controller operation is not used, screen will go into energy savings mode.
● During the indoor unit operation, press the desired ventilation mode button.
- You can select Auto, Recovery, or Bypass mode.
● During the indoor unit operation, press the desired ventilation mode button.
● During the operation of the indoor unit, press the mode button on the screen.
- You can select Auto, Recovery, or Bypass mode.
Ventilation mode
Function Description
It measures the ventilation system’s indoor temperature and outdoor temperature to automatically operate in the optimal ventilation mode.
Perform both air supply/discharge ventilation through the heat exchanger. Suitable for use in Summer/Winter during large temperature differences between indoor/outdoor.
Used to keep discharged air from entering the heat exchanger.
Used during the Spring/Fall seasons to keep allergens or pollutant
from entering the room.
● Press the remote controller screen’s temperature control button to set the desired temperature.
- In cooling, heating, and automatic mode, you can control the desired temperature.
ENGLISH
General Ventilation Operation Mode
71
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 72
72 FAN SPEED SETTING - Ventilator
ADDITIONAL MODE SETTING - Ventilator 73
ADDITIONAL MODE SETTING - Ventilator
Fan speed Control
Fast Mode
Remove sentence.
It quickly performs ventilation in a short period of time.
It is a function for more efficient operation of the ventilation function through the fast mode,
which is an additional function of the ventilation product.
● Choose a fan speed button to set the desired Fan speed.
- You can select the fan speed among Auto, Low, High, or Power.
- For direct ventilation, press the fan speed button to select the fan speed in the order of ‘Low’
→ ‘High’ → ‘Power’ → ‘Auto’.
- You can set and use the automatic fan speed after installing the air pollution (CO2) sensor.
● During operation, press the ‘Fast’ button.
- Every time you press the ‘Fast’ button, it switches between express mode ‘setting ↔ turned
off’ states.
Energy-Saving Mode
< General ventilation >
It performs Energy-Saving function at the same time of efficient ventilation.
● During operation, press the ‘Energy’ button.
- Evert time you press the ‘Energy’ button, it switches between Fast mode ‘setting’ ↔ turned
off’ states.
< Ventilation unit with DX>
! NOTE
• General ventilator and the direct expenditure type ventilator have same additional operations (Fast mode, Energy-Saving mode).
• The additional operation setting method of the air cleaning/heater/humidifier, etc. are the
same as the air conditioner.
ENGLISH
FAN SPEED SETTING - Ventilator
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 74
74 TIMER & PROGRAM
● In the easy timer setting menu screen, press ‘Disable/Enable’ button to set or turn off the easy
timer.
Simple Reservation
"Setting has the option to be set between 1-7 hours in 1 hour increments.
● Press the remote controller screen’s ‘Timer Setting menu’ button.
- It moves to the Timer Setting menu screen.
● During the Simple Reservation setting, press ‘▲’, ‘▼’ button to set the simple reservation
time.
- You can select from 1~7 hours.
● In the Timer Setting menu screen, press ‘Timer’ button.
- It moves to the timer setting screen.
● Press the Save button when done.
- If you exit without pressing the Save button, your settings will not be saved.
● In the timer setting menu screen, press ‘Simple Reservation’ category.
- It moves to the easy timer setting screen.
ENGLISH
TIMER & PROGRAM
TIMER & PROGRAM 75
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 76
76 TIMER & PROGRAM
Sleep Reservation
Sleep Reservation Places the unit into sleep mode or lets the unit know to stop at a certain time.
After connection with ventilation product, During the Sleep Reservation Setting, The system operations in
Sleep mode, and when it passes the set time, only the Sleep Reservation is turned off.
● Press the remote controller screen’s ‘Timer Setting menu’ button.
- It moves to the Timer Setting menu screen.
● In the Timer Setting menu screen, press the ‘Timer’ button.
- It moves to the timer setting screen.
● In the timer setting menu screen, press the ‘Sleep Reservation’.
- It moves to the Sleep Reservation Setting screen.
- Sleep Reservation can be activated when the indoor unit is in operation.
ENGLISH
● If you press ‘Cancel’ or ‘Home’ button, it will exit from the setting menu.
- If no buttons are pressed for 60 seconds, it will automatically exit from the setting menu.
TIMER & PROGRAM 77
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 78
78 TIMER & PROGRAM
● During the Sleep Reservation setting, press ‘▲’, ‘▼’ button to set the sleep activation time.
- Air conditioner: You can select from 1~7 hours.
- Ventilation: You can select from 1~12 hours.
● Press the Save button when you are done to save all changes.
- If you exit without pressing the Save button, your setting changes will not be applied.
● If you press ‘Cancel’ or ‘Home’ button, it will exit from the setting menu.
- If no buttons are pressed for 60 seconds, it will automatically exit from the setting menu.
ENGLISH
● In the Sleep Reservation Setting menu screen, press ‘Disable/Enable’ button to set or turn off
this function.
TIMER & PROGRAM 79
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 80
80 TIMER & PROGRAM
The unit is instructed to turn on at a set time automatically.
● In the Turn-On Reservation Setting menu screen, press ‘Disable/Enable’ button to set or turn
off ‘Turn-On Reservation’.
● Press the remote controller screen’s ‘Timer Setting menu‘ button.
- It moves to the Timer Setting menu screen.
● Press ‘▲’, ‘▼’ button to set to turn on time.
● In the Timer Setting menu screen, press ‘Daily’ button.
- It moves to the Daily Timer Setting screen.
● In Daily Timer Setting menu screen, press ‘ON Timer’ category.
- It moves to ON Timer Setting screen.
● Press the Save button well done.
- If you exit without pressing the Save button, your changes will not be applied.
ENGLISH
Turn-On Reservation
TIMER & PROGRAM 81
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 82
82 TIMER & PROGRAM
Turn-Off Reservation
The indoor unit is automatically turned off at the a set time.
● Press the remote controller screen’s ‘Timer Setting menu‘ button.
- It moves to the Timer Setting menu screen.
● In the Timer Setting menu screen, press ‘Daily‘ button.
- It moves to the Daily Reservation Setting screen.
● In the Daily Timer Setting menu screen, press ‘Turn-Off Reservation’ category.
- It moves to the OFF Timer setting screen.
ENGLISH
● If you press ‘Cancel’ or ‘Home’ button, it will exit from the setting menu.
- If no buttons are pressed for 60 seconds, it will automatically exit from the setting menu.
TIMER & PROGRAM 83
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 84
84 TIMER & PROGRAM
● Press ‘▲’, ‘▼’ button to set to turn off time.
● Press the Save button well done.
- If you exit without pressing the Save button, your changes will not be applied.
● If you press ‘Cancel’ or ‘Home’ button, it will exit from the setting menu.
- If no buttons are pressed for 60 seconds, it will automatically exit from the setting menu.
ENGLISH
● In the OFF Timer Setting menu screen, press ‘Disable/Enable’ button to set or turn off the OFF
Timer.
TIMER & PROGRAM 85
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 86
86 TIMER & PROGRAM
You can create and edit 7-day patterns that can be applied to weekly and yearly schedules
● Create a new pattern
- In the 7-Days schedule screen, press ’Edit’ button, to edit patterns.
- Select one from the pattern list marked as ‘Empty’.
● Edit the existing patterns
- In the 7-Days schedule screen, press ’Edit’ button, enter to edit patterns.
- Select a pattern to edit among the existing registered patterns.
● Naming of the 7-Days pattern.
- You can select the name according to the desired usage among the pattern name list by selecting the pattern name edit box.
- Select the pattern name and select ‘Next’ button, then you can set the detail event setting.
- When editing, if you do not need to change the pattern name, you can move directly to the
next step.
ENGLISH
Create and Edit 7-Days Pattern
TIMER & PROGRAM 87
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 88
88 TIMER & PROGRAM
● Set the detail event.
- When setting up a specific time through the weekly schedule screen, start by pressing the up
or down smaller arrows located above and below the "ON" circle as shown below.
- Pressing the center area of the circle, toggles the time On or Off and advances to the next
event (example: mode, temperature, fan speed) as outlined in the flow setting below.
Indoor unit event setting flow : On/Off → mode → temperature → fan speed
On/Off → occupancy → mode → temperature → fanspeed(in 2set
control mode)
* If you select Auto mode in 2set control operating mode increases the desired temperature setting step.(cooling temperature → heating temperature)
Ventilation event setting flow: On/Off → mode → fan speed
● Select the day of week and time to set the desired control event.
- Choose the desired day off week, by pressing one of the days of the week buttons. Note that
you can choose only one day of the week at a time.
- Press the left or right arrow keys on the display to scroll the timer. You can also press the
AM/PM button at the top of the screen to switch to morning or evening hours.
- When choosing a time period, you can make choices in half and hour increments (30 minute
time units).
ENGLISH
● Through the event edit, set the desired controls.
- The Edit button will change to Save, so you can save your control settings.
TIMER & PROGRAM 89
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 90
90 TIMER & PROGRAM
TIMER & PROGRAM 91
● Press Save, once the event has been deleted.
- If you exit without pressing the Save button, the changes will not be applied.
● Delete a detail event.
- To delete an event, press and hold for 2 seconds, a message to confirm whether to delete
the event is displayed on the screen.
7-Days Pattern Deletion
● In the weekly timer setting menu screen, press ‘Edit’ button.
- It switches to the weekly timer edit state.
● Press ‘Delete’ button next to the pattern name to delete.
ENGLISH
● You can register up to 5 events per day of week.
- The following warning display will pop up on the screen if you try to schedule over 5 events.
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 92
92 TIMER & PROGRAM
7-Days Pattern – Day of Week Event Copy/Paste
● In the weekly timer setting screen, press ‘Edit’.
- It enters the weekly timer edit mode.
● In the weekly timer setting - timer event setting screen, press and hold the day of week button
for 3 seconds to ‘copy’.
- The timer copied day of week button will have a frame mark.
● The screen to select day of week will be displayed.
- The day of w`eek to copy.
ENGLISH
● The following confirmation message window is displayed.
- Press ‘OK’ button to delete.
TIMER & PROGRAM 93
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 94
94 TIMER & PROGRAM
TIMER & PROGRAM 95
ENGLISH
Weekly Schedule
You can set the weekly schedule events in the unit of a week.
Note : Once you set the weekly schedule, the function will continue until it is cancelled.
● Press the remote controller screen’s ‘Timer Setting menu’ button.
- It moves to the Timer Setting menu screen.
● In the Timer Setting menu screen, press ‘7-Days’ button.
- It moves to the Weekly Timer Setting screen.
● In the weekly timer pattern list, select the pattern to apply to the weekly timer.
- When you select the desired pattern among the weekly schedule, a confirmation message
window is displayed.
- If you select Confirm in the confirm message window, it is immediately applied, and the selection check will be marked next to the corresponding pattern name.
● Turning off the application of the pattern applied to the weekly schedule, haults weekly scheduled operation.
- If you select the pattern applied to the weekly timer one more time, turn off confirmation window is displayed.
- The weekly schedule will be cleared of the checkmark indicating that no schedule is associated to it.
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 96
96 TIMER & PROGRAM
You can set yearly schedules that can be applied by month.
It uses the weekly schedule to perform the Yearly schedule function.
● In the yearly schedule screen, press the desired time area.
- Yearly Timer event is created.
● Press the remote controller screen’s ‘Timer Setting menu’ button.
- It moves to the Timer Setting menu screen.
● In the Timer Setting menu screen, press ‘Yearly’ button.
- It moves to the Yearly schedule Setting screen.
● Press ‘<’, ‘>‘ button to advance through each month's numerical equivalent (1=Jan, 2=Feb, etc.)
- You can adjust in the units of ‘month’.
- Example) June, July, August
● Press ▲, ▼ button to select the weekly schedule pattern to use in the yearly schedule operation.
- You can set the Yearly schedule setting only when the weekly timer pattern is created.
● After selecting the yearly schedule, set by pressing the center circle.
ENGLISH
Yearly Schedule
TIMER & PROGRAM 97
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 98
98 TIMER & PROGRAM
Holiday
It automatically stops on the set date.
If the operation is set, the operation stops at every o’clock.
● Press the remote controller screen’s ‘Timer’ button.
- It moves to the Timer Setting screen.
Delete Yearly Schedule
● In the yearly schedule screen, press ‘Edit’ button.
- The yearly schedule screen will be placed into edit mode.
● In the Timer Setting screen, press ‘Holiday‘ button.
- It moves to the Holiday Setting screen.
● Press the yearly event for 2 seconds or longer to delete.
- Yearly schedule event will be deleted.
- Verify the deletion, and press ’Save’ button to apply the change.
Add Holiday
● In the Holiday Timer Setting screen, press ‘Edit’.
- It changes to a state that you can add scheduled holiday.
ENGLISH
● Press the ‘Save’ button to save the set desired reservation.
- If you exit this screen before pressing the Save button, the changes will not be applied.
TIMER & PROGRAM 99
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 100
100 TIMER & PROGRAM
● In the Holiday Timer screen, press ‘Done’ button one more time to complete the addition of
Holiday.
- If you exit without pressing the ‘Done’ button, your changes will not be applied.
- Pressing Done will close the edit mode of this screen.
● Press ‘▲’, ‘▼’ button to set the date for a scheduled holiday.
● Press ‘Home’‘, Go Back’, or ‘Home’ button to exit from the setting screen.
● Press Done to commit any date changes.
- If you exit without pressing the Finish button, your changes will not be applied.
ENGLISH
● Press empty to add a scheduled Holiday event.
- It moves to Add Holiday screen.
- You can make any changes to an already set timer for that Holiday.
TIMER & PROGRAM 101
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 102
102 TIMER & PROGRAM
● In the Holiday screen, press ‘Edit’.
- It is changed to the state that you can delete a Holiday.
- ‘Delete’ button is displayed on the right side of the section set as a holiday.
● Press the Holiday you want to delete and then press the Delete button to the right of that Holiday.
● After the deletion, press ‘Done’.
- If you exit without pressing the ‘Done’ button, your changes will not be applied.
● Press ‘Home’, ‘Go Back’, or ‘Home’ button to exit from the setting screen.
ENGLISH
Delete Holiday
TIMER & PROGRAM 103
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 104
104 ENERGY
Check Energy Usage
You can check energy usage (operation time, power consumption).
● In the Energy Saving menu screen, press ‘Weekly’ button to view the weekly energy usage
goal and the usage amount.
- The energy usage is displayed as a bar graph for each day of the week. The bars are color
coded to indicate if the usage is under (green), near (yellow) or over (red) the target/goal energy setpoint.
● Press the remote controller screen’s ‘Energy Saving menu’ button.
- It moves to the Energy Saving setting menu screen.
● From the Energy Saving setting screen, you can view the energy usage.
- Unit operation will be shown in total hours, while power consumption units will be shown in
total KWh.
- The power consumption can be verified only when it is connected to the indoor unit that supports the power consumption information display function.
● Press ‘◀‘, ‘▶’ button to move between the energy usage display ‘month’.
● In the Energy Saving menu screen, press ‘Monthly’ button to check the monthly energy usage
goal and the usage amount.
- The energy usage is displayed in the units of ‘week’ for the indicated month.
- The bars are color coded to indicate if the usage is under (green), near (yellow) or over (red)
the target/goal energy setpoint.
- Note: Depending on the specific month, you might see 4 or 5 week bars.
● In the Energy Saving menu screen, press ‘Yearly’ button to check the yearly energy usage goal
and the usage amount. The bars are color coded to indicate if the usage is under (green), near
(yellow) or over (red) the target/goal energy setpoint.
- The energy usage is displayed in the units of ‘month’.
ENGLISH
ENERGY
ENERGY 105
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 106
106 ENERGY
Target Energy Consumption
This function is that user can set daily amount target usage.
After setting the daily target value, weekly and monthly targets will be calculated and applied automatically. (Please refer to the "check energy usage" section of this manual. )
The daily target value is used as the reference value in the graph displays of each period (weekly,
monthly, yearly). (Please refer to the "Alarm Popup" section of this manual.)
● Press the remote controller screen’s ‘Energy menu’ button.
- It moves to the Energy Saving screen.
● In the Energy Saving screen, press ‘Settings’ button.
- It moves to the Energy saving setting screen.
● In the Energy Saving setting screen, press ‘Energy Usage Limit’ menu.
- It moves to the Target Energy Consumption setting screen.
ENGLISH
● The guide to the energy consumption display is as follows.
It is displayed in 3 stages (good, normal, bad) compared to the previous year’s information.
- The display compares each year at the same month (year over year). The three screens
below, show each energy savings scenario. Green indicates a significant energy savings. Yellow is a normal or on target energy savings. Red indicates that there was a higher energy
usage than the previous year of the same month.
ENERGY 107
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 108
108 ENERGY
● Set the energy usage.
- If you touch the box at the bottom of the daily target amount, you can set the energy usage
using the umeric keypad.
- During the daily target amount setting, the weekly target amount and the monthly target
amount are automatically calculated and displayed.
h Weekly target amount: Daily target amount x 7
h Monthly target amount: Daily target amount x 31
● Press the Done button to save the set Target Energy Consumption setting.
- If you exit without pressing the Done button, your changes will not be applied.
Operation Time Limit
This function is that user can set daily amount target usage.
After setting the daily target value, weekly and monthly targets will be calculated and applied automatically. (Please refer to the "check energy usage" section of this manual. )
The daily target value is used as the reference value in the graph displays of each period (weekly,
monthly, yearly). (Please refer to the "Alarm Popup" section of this manual.)
● Press the remote controller screen’s ‘Energy menu’ button.
- It moves to the Energy screen.
● In the Energy Saving screen, press ‘Settings’ button.
- It moves to the Energy setting screen.
● In the Energy Saving setting screen, press ‘Operation Time Limit’ from the menu.
- It moves to the Operation Time Limit setting screen.
ENGLISH
● In the Target Energy Consumption setting screen, press ‘Disable/Enable’ button to select
whether to set the target amount.
ENERGY 109
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 110
110 ENERGY
Time Limit Control
It is the function to save energy by operating the product only for the set time and automatically
stopping the operation after starting the product operation.
● Press the remote controller screen’s ‘Energy Saving menu’ button.
- It moves to the Energy Saving setting menu screen.
● Set the operation hours.
- If you touch the box at the bottom of the daily target amount, you can set the operation hours
using the umeric keypad.
- During the daily target amount setting, the weekly target amount and the monthly target
amount are automatically calculated and displayed.
h Weekly target amount: Daily target amount x 7
h Monthly target amount: Daily target amount x 31
● Press the Done button to save the set Target Operation Hours.
- If you exit without pressing the Done button, your changes will not be applied.
● In the Energy Saving setting screen, press ‘Settings’ button.
- It moves to the Energy Saving setting screen.
● In the Energy Saving setting screen, press ‘Time Limit Control’ from the menu.
- It moves to the Time Restriction Operation Setting screen.
ENGLISH
● In the Operation Time Limit setting screen, press ‘Disable/Enable’ button to select whether to
set the target amount.
ENERGY 111
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 112
112 ENERGY
Alarm Popup
This function allows you to set up a popup notice message for the Power Consumption and Operation Time Restriction feature. It will be displayed on the remote controller once a percentage
threshold is reached (i.e., 80%, 90% etc. of power consumption or time target).
● Press the remote controller screen’s ‘Energy’ button.
- It moves to the Energy screen.
● Press ‘▲’, ‘▼’ button to set the operation hours.
● In the Energy Saving screen, press ‘Settings’ button.
- It moves to the Energy setting screen.
● Press the Done button to save the set time value.
- If you exit without pressing the Done button, your changes will not be applied.
● In the Energy setting screen, Press ‘Alarm Popup’ button.
- It moves to the Alarm Popup setting screen.
h When the operation stops, the calculated time value will reset to its initial value.
Example: If the Time Limit Control is set to operate for 1 hour, but the unit is prematurely
stopped after 25 minutes, the time will reset back to the full 1 hour control limit. The
next time the unit begins operation, it will again start at the 1 hour limit mark to
countdown.
ENGLISH
● In the Time Limit Control Setting screen, press the Enable button to begin setting a time limit.
ENERGY 113
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 114
114 ENERGY
Initialization Usage Data
This function is used to initialize energy and time usage information. Once you initialize the data,
all the usage information will be reset and all the usage data will be deleted.
● Press the remote controller screen’s ‘Energy’ button.
- It moves to the Energy screen.
● After setting the alarm or notice display setting, you can press ‘Back’, ‘Go Back’, or ‘Home’
button, to exit from the screen.
● In the Energy Saving screen, press ‘Set’ button.
- It moves to the Energy setting screen.
● For the categories with Alarm Popup setting, the popup is displayed on the remote controller
screen when it reaches 80%, 90%, 95%, and 100% of the target usage amount.
Example) Display when it reaches 80% of the target usage amount
● In the Energy setting screen, press ‘Initialization Usage Data‘ button.
- It moves to the Energy information initialization screen.
ENGLISH
● Press ‘Disable/Enable’ button to set or turn off the category to use.
- Once you press Enable, the notice determination period (daily/weekly/monthly) will be displayed on the screen. Choose the notice determination period.
ENERGY 115
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 116
116 ENERGY
FUNCTION SETTING
Lock Setting – All Lock, On/Off Lock, Mode Lock
This function locks the remote controller’s button operation to prevent the unauthorized operation by children or others.
● While unit is in operation, press ‘Set’ button.
- It moves to the ‘settings’ screen.
● If you press ‘Done’ button, it will start to delete the data.
- The Notice popup message will display until the deletion process has completed.
● In the setting menu list, press ‘Lock’ button.
- It moves to the ‘Lock’ setting screen.
● From the Release/Lock button choices, press Lock to activate the lock function, and press
‘Done’ button to save the setting.
- If you exit without pressing the ‘Done’ button, your changes will not be applied.
- Once you press the ‘Done’ button, the setting screen will close.
ENGLISH
● Select the checkbox to the left of ‘Initialization Usage Data‘.
FUNCTION SETTING 117
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 118
118 FUNCTION SETTING
FUNCTION SETTING 119
The Temperature Lock function locks the ability to set the temperature beyond a preset value
setting.
h The changes to the desired temperature by external equipments(Central Controller, Dry contact, Wireless Remote Controller) will not be affected the wired remote controller’s desired
temperature range lock.
h If the temperature range lock is set from the central controller, the desired temperature range
lock setting of the wired remote controller is released.
● In 1Set Point Control type) Press ‘Cancel‘, ‘Go Back’, or ‘Home’ button to exit from the setting
screen.
● In the Lock setting screen, press ‘Temperature Lock’ button.
● (In 2Set Point Control type) In the Temperature Range Lock setting menu, press
‘Release/Lock’ button to set the lock function, and press ‘Done’ button to complete the temperature range lock setting.
● (In 1Set Point Control type) In the Temperature Range Lock setting menu, press
‘Release/Lock’ button to activate the lock function, and press ‘Done’ to complete the temperature range lock setting.
- If you press the ‘Done’ button, it will exit from the setting screen.
- Press the up and down arrow buttons from the Minimum and Maximum settings to adjust
the temperature range as needed. Be sure that the Lock button is set once your temperature
adjustments are made. Press Done to commit the changes.
Possible setting
boundary
Lower Limit
Upper Limit
16~30 °C
(60~86 °F)
18~30 °C
(64~86 °F)
Indoor unit Control
Method
1set point
2set point
Option
Cooling Set point range Heating Set point range
(Installer code No.31)
31:000
64~86 °F (18~30 °C)
60~86 °F (16~30 °C)
31:000
64~99 °F (18~37.5 °C)
40~86 °F (4~30 °C)
-
50~99 °F (10~37.5 °C)
40~90 °F (4~32 °C)
● (In 2Set Point Control type) Press ‘Cancel‘, ‘Go Back’, or ‘Home’ button to exit from the setting
screen.
ENGLISH
Lock Setting – Temperature Lock
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 120
120 FUNCTION SETTING
FUNCTION SETTING 121
Filter Sign Check
This function gives you the option to view a "Filter Sign" message so that you can check the status of the condition of the filter and gauge when it should be changed.
● Press ‘Set’ button.
- It moves to the ‘settings’ screen.
Lock Category
All Lock
Description
Locks operations of all the buttons of the remote controller.
On/Off Lock
Locks the remote controller’s On/Off button.
Mode Lock
Locks the remote controller’s operation mode button.
Temperature Range Lock
● In the setting menu list, press ‘Filter Sign’ button.
- It moves to the ‘Filter Sign’ setting screen.
Sets the remote controller’s desired temperature range which
can be changed only within the set boundary.
● When the filter cleaning indicator is displayed on the top right side of the screen, you can initialize the filter status by pressing the ‘Reset’ button in the Filter Sign menu.
- When it is the time to clean the filter, the filter icon appears on the top right side of the
screen, and you can enter the Filter Sign menu.
h If your units functionality allows it to display time remaining until the filter cleaning, you can
enter the Filter Sign menu even if the filter cleaning alarm icon is not displayed.
ENGLISH
● If you press ‘Cancel’, ‘Go Back’, or ‘Home’ button, it will exit from the setting screen.
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 122
122 FUNCTION SETTING
Elevation Grill Setting
This function allows you to operate the elevation grill for indoor unit filter cleaning.
● While unit is in operation, press ‘Set’ button.
- It moves to the ‘settings’ screen.
- If there is time remaining until the next filter cleaning alarm, you can enter the ‘Filter Sign’
menu even if the filter cleaning alarm icon has not displayed as yet.
● In the setting menu list, press ‘Elevation Grill’ button.
- It moves to the ‘Elevation Grill’ setting screen.
● If you press ‘Cancel’, ‘Go Back’, or ‘Home’ button, the system will exist out of this screen.
● Press ‘Up/Stop/Down’ button to set the elevation grill’s movement.
! NOTE
• If dust is accumulated in the filter, cooling/heating ability is degraded, and the electricity bill will
increase, so make sure to clean the filter when it becomes the time to clean the filter.
• Filter cleaning alarm icon will be disappeared after certain time.
ENGLISH
● Example) If indoor unit has a function to display the remaining time,
- If you unit has the capability to display the remaining time until the filter cleaning alarm, the
following screen below is displayed in the current time display area.
FUNCTION SETTING 123
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 124
124 FUNCTION SETTING
Robot Cleaning
Robot cleaning is the function for the cleaner attached to the product to perform automatic filter
cleaning after certain time of the air conditioner usage. Set the robot cleaning to operate manually or automatically. It can be set 30 seconds after indoor unit turn off.
● Press the screen’s ‘Set’ button.
- It moves to the settings menu.
● In the settings menu, press ‘Robot Cleaning’ button.
● Press ‘Auto/Manual’ button to set the desired state, and If you press ‘Back’, ‘Go Back’, or
‘Home’ button, it will exit from the setting screen.
! NOTE
Robot cleaning function may not work in some indoor unit products.
ENGLISH
● Press ‘Back’, ‘Go Back’ or ‘Home’ button to exit from the setting menu.
FUNCTION SETTING 125
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 126
126 FUNCTION SETTING
FUNCTION SETTING 127
Change Temperature
Auto dry removes moisture by drying the inside of the indoor unit after cooling operation once
the indoor unit is turned OFF.
This function allows you to set the temperature to automatically switch between cooling and
heating operation as setup in the artificial intelligence operation mode.
● Press the screen’s ‘Set’ button.
- It moves to the settings menu.
● In the settings menu, press ‘Auto Dry’ button.
● Press ‘Disable/Enable’ button to set the desired state, and If you press ‘Back’, ‘Go Back’, or
‘Home’ button, it will exit from the setting screen.
! NOTE
Auto dry function may not work in some indoor unit products.
● Press the screen’s ‘Set’ button.
- It moves to the settings menu.
● In the settings menu, press ‘Change Temp.’ button.
● Press ‘▲’, ‘▼’ buttons to set the switching temperature value, and press ‘Save’ button to save
the setting.
- Switching temperature boundary: It can be set from 1~7.
- If you exit without pressing the Save button, your settings will not be applied.
- If you press the Save button the changes will be applied and, it will exit from the setting
screen.
ENGLISH
Auto Dry
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 128
128 FUNCTION SETTING
FUNCTION SETTING 129
Wireless Module AP mode
Wireless Module AP mode function that wireless module change to AP mode.
● Press the screen’s ‘Set’ button.
- It moves to the settings menu.
● In the settings menu, press ‘Wi-Fi Module AP Mode’ button.
h It is the function that can be used only in cooling/heating product.
Example of using the change temperature function
● Conditions
1) Mode: artificial intelligence mode
2) Desired temperature: 22 °C
3) Change temperature: 3
→ Difference of change temperature is 3 °C
Temperature[°C]
Cooling changeover
25°C
22°C
19°C
Heating changeover
● The illustration in this section shows the example of operation as set through the conditions in
the example above.
Time
● Press ‘Apply’ button to set the desired state, and then press ‘Back’,
‘Go Back’, or ‘Home’ button, then exit from the setting screen.
! NOTE
Wireless module AP mode function may not work in some indoor unit products.
ENGLISH
● Press ‘Cancel’, ‘Go Back’ or ‘Home’ button to exit from the setting screen.
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 130
130 FUNCTION SETTING
● Push each zone button, then select a desired zone name.
Zone Control settings allow you to select zone name.
● Press the screen’s ‘Set’ button.
- It moves to the settings menu.
● Select zone name and then press the “Done” button.
● In the settings menu, press ‘Zone Control’ button.
! NOTE
Zone Control setting function may not work in some indoor unit products.
ENGLISH
Zone Name Setting
FUNCTION SETTING 131
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 132
132 FUNCTION SETTING
FUNCTION SETTING 133
Home Leave Set Temperature
Override Set Time function can only be used in 2 Set Control mode.
When timed override is used, the set time will be a default value.
Home Leave Set Temperature function is used in 2 Set control mode.
When customer operate as home leave mode, this setting temperature value will be applied.
● Press the screen’s ‘Set’ button.
- It moves to the settings menu.
● Press the screen’s ‘Set’ button.
- It moves to the settings menu.
● In the settings menu, press ‘Override Set Time’ button.
● In the settings menu, press ‘Home Leave Set Temp’ button.
● Select time increment using ‘▲’, ‘▼’ buttons, and then press ‘Save’.
If you press ‘Cancel’, ‘Go Back’, or ‘Home’ button, before pressing 'Save', you will exit the
screen and your changes will not be applied.
● Select temperature using ‘▲’, ‘▼’ buttons, and then press ‘Save’.
If you press ‘Cancel’, ‘Go Back’, or ‘Home’ button, without pressing 'Save', you will exit the
setting screen and you changes will not be applied.
! NOTE
Override Set Time function can only be used in a 2 set control mode.
! NOTE
Home Leave Set Temperature function can only be used in a 2 set control mode.
ENGLISH
Override Set Time
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 134
134 FUNCTION SETTING
Dead Band function is used with a 2 Set control mode.
When heating and cooling desired temperatures have been changed, the set value will maintain a
difference between the heating and cooling desired temperature.
● Press the screen’s ‘Set’ button.
- It moves to the settings menu.
● In the settings menu, press ‘Dead Band’ button.
● Select degrees of separation using ‘▲’, ‘▼’ buttons, and then press ‘Save’.
If you press ‘Cancel’, ‘Go Back’, or ‘Home’ button, without pressing 'Save', you will exit the
setting screen and you changes will not be applied.
h available setting range : 0~10°F(0~5°C)
! NOTE
Dead Band function only can use in 2 set control mode.
• When changing the desired cooling temperature, in case of that the difference with the
heating temperature becomes lesser than its minimal value of difference, it lowers the desired heating temperature automatically.
• When changing the desired heating temperature, in case of that the difference with the
heating temperature becomes lesser than its minimal value of difference, it raises the desired cooling temperature automatically.
ENGLISH
Dead Band
FUNCTION SETTING 135
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 136
136 FUNCTION SETTING
Ventilation mode is activated after the preset delay time.
● Press ‘Done’ button to save the changed Delay Time.
- If you exit without pressing ‘Done’ button, your changes will not be applied.
● Press the screen’s ‘Set’ button.
- It moves to the settings menu.
● In the settings menu, press ‘Delay Time’ button.
● Select delay time ‘OFF/ON’ button.
- If you select ON, the number key pad and edit box are displayed at the bottom.
● If you press ‘Cancel’ or ‘Home’ button, without pressing 'Save', you will exit the setting screen
and you changes will not be applied.
- If no buttons are pressed after 60 seconds, it will automatically exit from the edit menu.
ENGLISH
Delay Time - Ventilator
FUNCTION SETTING 137
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 138
138 USER SETTING
Date Setting
● After setting the year, month, day, and day of week, press ‘Save’ button to save the settings.
- If you exit without pressing the Save button, your changes will not be applied.
- If you press the Save button, it will exit from the setting screen with your changes applied.
This functions allows you to set the current date to be displayed on the remote controller.
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● If you press ‘Cancel’, ‘Go Back’, or ‘Home’ button, without pressing 'Save', you will exit the
setting screen and you changes will not be applied.
● In setting screen, press ‘User’ button at the bottom of the screen.
- It moves to the User Setting screen.
● In User Setting screen, press ‘Date’ button.
- It moves to the Date Setting screen.
ENGLISH
USER SETTING
USER SETTING 139
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 140
140 USER SETTING
This functions allows you to set the current time to be displayed on the remote controller.
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● In setting screen, press ‘User’ button.
- It moves to the User Setting screen.
● In User Setting screen, press ‘Time’ button.
- It moves to the Time Setting screen.
● Press ‘▲’, ‘▼’ buttons to set ‘AM/PM’, hour, and minute, and then press the ‘Save’ button to
apply the settings.
- If you exit without pressing the Save button, your changes will not be applied.
- If you press the Save button, it will exit from the setting screen.
● If you press ‘Cancel’, ‘Go Back’, or ‘Home’ button, without pressing 'Save', you will exit the
setting screen and your changes will not be applied.
ENGLISH
Time Setting
USER SETTING 141
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 142
142 USER SETTING
This function allows you to set a password so that children or others cannot change the remote
controller setting without permission.
● Press ‘OFF/ON’ button to set whether to apply the password.
- Pressing "ON" will display 4 numeric boxes in order to enter your 4 digit code.
● DPress the screen’s Set’ button.
- It moves to the settings menu screen.
● Enter the 4 digit code for your password into the fields as shown and press Done when completed. The numeric keypad will disappear when done.
● In setting screen, press ‘User’ button.
- It moves to the User Setting screen.
Change Password
● In User Setting screen, press ‘Password’ button.
- It moves to the Password Setting screen.
● In the Password Setting screen, press ‘Change Password’ button.
- It moves to the password change screen.
ENGLISH
Password Setting
USER SETTING 143
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 144
144 USER SETTING
USER SETTING 145
Main Screen Display Setting
● If you press ‘Back’, ‘Go Back’, or ‘Home’ button, without pressing 'Done', you will exit the setting screen and your changes will not be applied.
● In setting screen, press ‘User’ button.
- It moves to the User Setting screen.
This function allows you to show or hide certain elements on the remote controller’s default
screen.
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● In User Setting screen, press ‘Main Screen’ button.
- It moves to the main screen setting screen.
ENGLISH
● In order to change the password, you will be asked to input the current password as verification. When done, move to entering the new password code in the "Input New Password"
screen. Then you will be asked to reenter (to confirm) the new password in the "Re-enter the
password" fields as shown below.
- Enter each password, and you need to press ’Done’ button to proceed to the next step.
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 146
146 USER SETTING
LCD brightness in idle
This function allows you to adjust the brightness of the remote controller’s standby screen.
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● If you press ‘Back’, ‘Go Back’, or ‘Home’ button, it will exit from the main screen setting
screen.
● In setting screen, press ‘User’ button.
- It moves to the User Setting screen.
● In User Setting screen, press ‘LCD Brightness In Idle’ button.
- It moves to the Brightness Setting screen.
ENGLISH
● Press ‘Hide/Show’ button to set the which elements should display on the default screen.
Note that the elements are dependant on the type of unit in operation.
USER SETTING 147
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 148
148 USER SETTING
USER SETTING 149
Screen Saver Timer Setting
● If you press ‘Cancel’, ‘Go Back’, or ‘Home’ button, without pressing 'Save", your changes will
not be applied and the screen will exit.
● In setting screen, press ‘User’ button.
- It moves to the User Setting screen.
This function adjusts the length of time that the screen will stay on before turning off (sleep
mode).
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● In User Setting screen, press ‘Screen Saver Timer’ button.
! NOTE
Setting the standby screen brightness to ‘30%’, may degrade LCD's illumination function.
ENGLISH
● Set the desired screen brightness percentage by and press ‘Save’ button to save the setting.
- If you exit without pressing the Save button, your changes will not be applied.
- Your choices are: 0% / 10% / 20% / 30%.
- Once you press the Save button, the screen will exit.
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 150
150 USER SETTING
USER SETTING 151
Schedule Initialization
● If you press ‘Cancel’, ‘Go Back’, or ‘Home’ button, without pressing 'Save", your changes will
not be applied and the screen will exit.
● In setting screen, press ‘User’ button.
- It moves to the User Setting screen.
It is the function to initialize all timer settings of the remote controller.
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● In User Setting screen, press ‘Schedule Initialization’ button.
! NOTE
If you choose 'not used' as your Screen Saver Timer choice, the LCD will remain on at all
times (will not dim) which will shorten your LCD display lifespan.
ENGLISH
● In the setting screen, choose the amount of time screen will stay on before it goes into sleep mode
and then press ‘Save’ button to save the setting.
- If you exit without pressing the Save button, your changes will not be applied.
- Your choices are: 15 seconds / 30 seconds / 1 minute / not used.
- Once you press the Save button, it will exit from the setting screen.
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 152
152 USER SETTING
Touch Beep
This function allows you to choose whether or not you would like a touch screen sound effect.
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● If you press ‘Back’, ‘Go Back’, or ‘Home’ button without pressing done, you will be returned to
the previous screen and your changes will not be applied.
● In setting screen, press ‘User’ button.
- It moves to the User Setting screen.
● In User Setting screen, press ‘Sound’ button.
- It moves to the touch beep setting screen.
ENGLISH
● Press the check box, and press ‘Done’ button to initialize all timer settings of the remote controller.
- Pressing the Done button, it will exit from the setting screen.
USER SETTING 153
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 154
154 USER SETTING
Home theme
You can change the amount of information you would like displayed on the home screen. There
are two modes. Standard mode and simple mode.
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● Press ‘Back’, ‘Go Back’, or ‘Home’ button to exit from the setting screen.
● In setting screen, press ‘User’ button.
- It moves to the User Setting screen.
● In User Setting screen, press ‘Home Theme’ button.
ENGLISH
● Press ‘Sound’ category’s ‘Disable/Enable’ button to set whether to use the touch beep.
- If you select ‘Disable’, no sound effect will occur when you press the keypad display.
- If you select ‘Enable’, you will have an audible beep for key presses on the display.
USER SETTING 155
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 156
156 USER SETTING
Temperature Unit Setting
This function allows you to set your unit of measure in whole or half degree increments.
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● If you press ‘Cancel’, ‘Go Back’, or ‘Home’ button, without pressing 'Save', the Home Theme
screen will be closed and your changes will not be applied.
● In setting screen, press ‘User’ button.
- It moves to the User Setting screen.
● If you choose the Advanced mode theme, you will see the following screen as your main screen.
● In User Setting screen, press ‘Temperature Unit’ button.
- It moves to the Temperature Unit Setting screen.
ENGLISH
● Select the desired Screen Mode and press the Save button.
Standard mode displays only the frequently used functions in the main screen.
USER SETTING 157
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 158
158 USER SETTING
USER SETTING 159
Language Setting
● If you press ‘Cancel’, ‘Go Back’, or ‘Home’ button, without pressing 'Save', the screen will be
closed and your changes will not be applied.
● In setting screen, press ‘User’ button.
- It moves to the User Setting screen.
This function allows the user to choose the local language for the display screen.
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● In User Setting screen, press ‘Language’ button.
- It moves to the Language screen.
! NOTE
This feature is not available in all products.
ENGLISH
● Set the temperature unit increments that you want to display, and press ‘Save’ button to save the
setting.
- You can select the temperature control in the units of 1°C / 0.5°C.
- If you exit without pressing the Save button, your changes will not be applied.
- If you press the Save button, it will exit from the setting screen.
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 160
160 USER SETTING
Control Type Setting(North America Only)
It is the function to set GUI type on the remote controller.
* If you want to use in other regions, except North America, does not fit in the environment are
expected to use this feature inconvenient.
We recommend that you use it only in the region (North America).
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● If you press ‘Cancel’, ‘Go Back’, or ‘Home’ button without pressing 'Save', it will exit from the
Language setting screen without saving any of the settings.
● In setting screen, press ‘User’ button.
- It moves to the User Setting screen.
● In User Setting screen, press ‘Control Type’ button.
- It moves to the Control Type Settings screen.
ENGLISH
● Set the language to use, and then press 'Save'.
- If you exit without pressing the Save button, your changes will not be applied.
- Once the Save button is press, after change value, it will Pop-up window appears.
- After waiting about 5 seconds if you push the reset button on the bottom of the remote control to
reboot the selected language.
* Please refer to “PART DESCRIPTION” section of the manual reset button location.
USER SETTING 161
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 162
162 USER SETTING
Summer Time Setting
It is the function to set summer time duration on the remote controller system date and time.
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● If you press ‘Cancel’, ‘Go Back’, or ‘Home’ button without pressing 'Save', it will exit from the
Control Type setting screen without saving any of the settings.
● In setting screen, press ‘User’ button.
- It moves to the User Setting screen.
● Replace sentence with " When 2 Set Point control is selected, a different main screen is displayed,
as shown below."
● In User Setting screen, press ‘Summer Time’ button.
- It moves to the Summer Time Setting screen.
ENGLISH
● Set the control type to use, and press ‘Save’ button when done.
- If you exit without pressing the Save button, your changes will not be applied.
- If the setting is changed by pressing the Save button, a pop-up window appears, perform the initialization schedule.
USER SETTING 163
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 164
164 USER SETTING
SERVICE SETTING
Service Contact
It is the function to check and input the telephone number of the service center that can be contacted when a defect occurs in the product.
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● If you press ‘Cancel’, ‘Go Back’, or ‘Home’ button, it will exit from the Summer time setting
screen without saving any of the settings.
● In setting screen, press ‘Service’ button.
- It moves to the Service Setting screen.
● In the service screen, press ‘Service Contact’ button.
- It moves to the Check Service Number screen.
ENGLISH
● Set summer time duration, and press ‘Save’ button when done.
- If you exit without pressing the Save button, your changes will not be applied.
- If you press the Save button, your changes will be applied and the controller will exit from the setting screen.
SERVICE SETTING 165
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 166
166 SERVICE SETTING
● Press ‘Done’ button to save the changed service number.
- If you exit without pressing the Done button, your changed value will not be applied.
- Once you press the Done button, it will exit from the setting screen.
Service number registration and change
● In the service number screen, press ‘Telephone’.
- It moves to the service number change screen.
● In the service number change screen, press the digits to input the service center number.
● If you press ‘Cancel‘, ‘Go Back’, or ‘Home’ button without pressing the 'Save' button, it will
exit from the service number screen and you changes will not be applied.
ENGLISH
● Check the service number.
- If the service number is not registered, + 1544 7777 will be displayed.
SERVICE SETTING 167
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 168
168 SERVICE SETTING
● Check indoor/outdoor unit and capacity information.
It is the function to check indoor/outdoor unit product type connected to the remote controller
and capacity information.
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● Once you press ‘Back’, ‘Go Back’, or ‘Home’ button, it will exit from the setting screen.
● In setting screen, press ‘Service’ button.
- It moves to the Service Setting screen.
● In service screen, press ‘Model Information’ button.
- It moves to indoor/outdoor unit information screen.
! NOTE
The indoor/outdoor unit information checking function is not available on all products.
ENGLISH
Model Information
SERVICE SETTING 169
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 170
170 SERVICE SETTING
● Check software version information of wired remote controller.
It is the function to check remote controller model name and software version.
This information is useful when having a service call placed.
● Press the screen’s Set’ button.
- It moves to the settings menu screen.
● If you press ‘Back’, ‘Go Back’, or ‘Home’ button, it will exit from the setting screen.
● In setting screen, press ‘Service’ button.
- It moves to the Service Setting screen.
● In service screen, press ‘Remocon Version Info.’ button.
- It moves to remote controller version information.
ENGLISH
Remocon version information
SERVICE SETTING 171
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 172
172 SERVICE SETTING
INSTALLATION 173
ENGLISH
Self-diagnosis for Trouble Mode
INSTALLATION
It automatically runs a self-diagnosis when there is a trouble detected in the system.
It displays the troble mode number with maintenance CODE.
Installation of Remote Controller
<Individual control>
● Secure the back plate flush to the wall using the provided hardware.
- Take care not to bend the back plate during installation as this may cause it to malfunction.
- If a reclamation box is included with your remote controller, install the remote controller installation plate as shown by the illustrations below.
<4 socket reclamation box installation>
<Group control>
<2 socket reclamation box installation>
● Remote controller’s wire may be installed at three different locations on the plate.
Select appropriate direction according to the installation environment.
- Wiring directions: wall reclamation, top side, or left side
- If you install the remote controller cable on top side or left side, install after removing the remote controller cable guide groove. (h Use pliers to remove guide groove.)
2. Top side guide groove
3. Left side
guide groove
In order to expedite a service, please remember the error number and provide it when consulting
an installer.
An emergency elevation grill can be operated even in the case of errors.
(Except the trouble mode number 03)
* If the centralized control lock or wired remote controller lock is programmed, this function will
not work.
* Some product may not include this function.
2. Top side guide groove
3. Left side guide groove
1. Wall reclamation
● Fix the remote controller top part to the back plate on the wall as shown in the figure below,
and press the bottom part to combine it with the back plate.
- Press together so that there is no gap between the remote controller and the
top/bottom/left/right side of the back plate.
- Before combining with the installation plate, arrange the cable so that it does not interfere
with the circuit parts.
<Order of Combining>
Wall
Wall
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 174
174 INSTALLATION
INSTALLATION 175
Group Control
Connects and controls 2 or more air conditioner indoor units to one wired remote controller.
h Use the group control cable for connection.
Indoor unit Main PCB
<Order of Separation>
Indoor unit 1
Master
RED(12V)
YELLOW(SIG)
BLACK(GND)
Wall
Indoor unit 2
Slave
YELLOW(SIG)
BLACK(GND)
Indoor unit 3
Slave
YELLOW(SIG)
BLACK(GND)
● Use the connection cable to connect the indoor unit and the remote controller.
12 V
Red
Signal cable
Yellow
GND
Black
Check if the connector is properly connected
Indoor unit
direction
Connection cable
● In the following cases, separately purchase and use the cable suitable for the situation.
- Do not install the cable for longer than 50 m. (It may cause communication defect like CH03)
- If the distance between the wired remote controller and the indoor unit is 10 m or longer:
Use 10 m extension cable. (Model : PZCWRC1)
- If several indoor unit products are controlled by one wired remote controller: Use group control cable. (Model : PZCWRCG3)
Purchase Specialized Company’s Accessories
① Group control cable (PZCWRCG3): Connect to indoor unit’s wired remote controller connector
② Extension cable (PZCWRC1): Connect to No. ① cable and slave indoor unit’s wired remote
controller connector
While No. ① cable is connected, connect No. ② cable.
1
2
! NOTE
! NOTE
• During the wired remote controller installation, do not reclaim in the wall. (It may cause
temperature sensor disorder.)
• Do not install the cable for longer than 50 m. (It may cause communication defect such as
Code CH03)
h During the installation of the extension cable, carefully check the connecting socket and
plug of the remote controller and linked indoor unit.
h If the extension cable is connected in reverse direction, connector will not make a solid
connection causing loss of communications.
h Specification of the extension cable: Use 2547 1007 22# 2core 3shield, 5 Ø or equivalent
or higher level.
• Connect only GND and signal cable to the indoor unit set as slave. (If power cable is also
connected, it may cause loss of communication)
• Inquiries related to the purchase of the cable shall be directed to the specialized company
and the service center.
● Check the existence of the event communication in the product manual, and change
master/slave of the remote controller.
- It only supports the interface with event communication applied models (corresponding to the
models after Multi-V Super II).
h For details, refer to ‘Remote controller master/slave‘.
ENGLISH
● To remove the remote controller from the back plate, insert a flat head screwdriver in the bottom part separation hole and turn clockwise.
- There are 2 separation holes at the bottom side. Slowly separate using each hole.
- During the separation, be careful not to damage the internal parts.
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 176
176 INSTALLATION
INSTALLATION 177
Master
GND
Signal cable
12V
Black
Slave
Slave
Air conditioner and ventilation interface
● Use wired remote controller to control when air conditioner indoor unit and ventilation product
are connected and installed at the same time.
- Once power is connection, and the remote controller establishes communication with the indoor unit, normal operation will commence.
Yellow
Red
GND Signal cable
Ȗ(Group control connection)
No. 3 switch OFF: master (factory ship-out based)
General
ventilation
- For details of the wireless remote controller master/slave setting changes, refer to the wireless remote controller manual.
- After completing the master/slave setting in the indoor unit, turn OFF the power of the indoor
unit, and turn the power ON again after 1 minute.
[General ventilation interfaced operation]
General
ventilation
[Direct ventilation
independent operation]
Direct
ventilation
• During the group control, set only one indoor unit as master.
• During the group control, some functions except default operation setting, fan Setting
Low/medium/high, remote controller lock setting, and time setting may be restricted.
• Slave set indoor unit cannot communicate with remote controller when remote controller
has a connection with only one indoor unit.
Interfaced operation
[general ventilation
independent operation]
Wired
remote
controller
No. 3 switch ON: slave
! NOTE
Independent operation
General
ventilation
Wired
remote
controller
Air conditioner
indoor unit
General
ventilation
Wired
remote
controller
[Direct ventilation interfaced operation]
Air conditioner
indoor unit
General
ventilation
Wired
remote
controller
h Connection method is the same as the air conditioner user manual. (Refer to the remote controller manual group control page.)
h Ventilation units represent general ventilation units and direct expenditure type ventilation
units.
Yellow
ENGLISH
● Change indoor unit’s master/slave setting.
- Change master/slave setting with switch on the indoor unit PCB for ceiling type cassette and
duct group.
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 178
178 INSTALLER’S SETTING OPTIONS
INSTALLER’S SETTING OPTIONS 179
Installer setting code table
How to enter installer setting mode
<General air conditioner product code table>
! CAUTION
Installer setting mode configures the detailed function of the remote controller.
If the installer setting mode is incorrectly set, it may cause product failure, user injury, or property damage. It must be set by an installation specialist who holds an installation license. If it is
installed or changed without installation license and without authorization, installer will be responsible for all malfunctions, which will result in voiding of any warranties or provision of free
technical service.
● When you press and hold the wireless remote controller signal receiver for 3 seconds or longer and
release it in the air conditioner or ventilation main screen, it enters the installer setting mode.
- When you enter from air conditioner screen, it enters air conditioner installer setting, and when
you enter from ventilation screen, it enters ventilation installer setting.
- If button is not pressed for at least 3 seconds, it will not enter the setting mode.
Code
Setting Mode
1
Test Run
2
Central control address setting
3
4
5
6
7
● In ‘Input Code’ screen, you can input code to carry out Installer Setting Function.
8
9
11
12
13
14
17
h During the input of the installer code, refer to the installer code If no buttons are pressed.
h If no buttons are pressed for about 60 seconds, it automatically exits from the setting screen.
! NOTE
Some categories of the menu may not be displayed or menu name may differ depending on
your specific indoor unit model type.
18
Value 1
001 : Cooling
002 : Heating
0~F : Group
<ESP step>
001 : SLOW
002 : LOW
ESP
003 : MED
004 : HIGH
005 : POWER
001 : remote controller
Temperature sensor 002 : indoor unit
003 : 2TH
Ceiling height
ENGLISH
INSTALLER’S SETTING OPTIONS
Setting Value
Value 2
Value 3
0~F : Unit
<ESP setting value>
0~255
001: low
002: standard
003: high
004: very high
001 : V-H
002 : F-H
003 : V-L
004 : F-L
Remote controller 000 : slave
master / slave setting 001 : master
Static pressure
Operation master /
000 : slave
slave setting
001 : master
(Mode Override)
Dry contact mode 000 : manual
setting
001 : automatic
Wind amount fixing 001 : variable
002 : fixed
Celsius / Fahrenheit 000 : Celsius
Switching
001 : Fahrenheit
000 : Old
Zone type
001 : New(4Zone)
002 : New(8Zone)
002~008 : Installed number
Zone number
Celsius control unit 000 : 1 °C control
setting
001 : 0.5 °C control
<Select mode>
Emergency Heater
000 : not use
Setting
001 : use
<Setup Low Ambient
Setup FAN
Heating Operation>
000 : not use
001 ~ 003 : Setting Step
001 ~ 015 : Setting Step
(step expand indoor unit)
<Setup Fan speed>
000 : fan off
001 : fan on
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 180
180 INSTALLER’S SETTING OPTIONS
19
Setting Mode
Function setting in
group control
Value 1
000 : use basic function only
001 : use basic function & some
Master indoor unit function
20
21
22
23
24
Plasma
Heater
Humidification
Elevation grill
Ventilation Kit
000: Not Installed
001: Installed
25
Auxiliary heater
000: Not installed
001: installed-General
002: installed-Duct type
26
29
Check indoor unit Address Number
Use Refrigerant leak- 000 : not use
age Sensor
001 : use
31
Setting temperature
range
000: 60~86 °F / 16~30 °C
001: 40~99 °F / 4~37.5 °C
32
Static Pressure step
000: use static pressure (code 06)
set value
001~011: static pressure step
(code 32) set value
Guard timer
000: 0 minute
001: 15 minutes
002: 30 minutes
003: 45 minutes
004: 60 minutes
33
35
Setting Value
Value 2
Cooling thermal off
Fan operation
000: Cooling thermal off Fan speed
-Low
001: Cooling thermal off Fan OFF
002: Cooling thermal off Fan speed
setting value
36
Use Primary Heater
control
000: Cancel primary heater control
001: use primary heater control
38
Air conditioner Fan
000: air-conditioner fan off
operation
001: air-conditioner fan operate
interlocked with venvery low
tilation
39
000: Use indoor unit auto restart
Indoor unit Auto-Start
001: not use indoor unit auto
setting
restart
40
Occupy sensor 'occupy maintain' time
setting
000: 0 minute
001: 10 minutes
002: 30 minutes
003: 60 minutes
41
Simple Dry Contact
Setting
00: Default
01: Not Use Simple Dry Contact
02: Use Simple Dry Contact
03: Use Programmable Digital Input
h Some contents may not be displayed depending on the product function.
ENGLISH
Code
INSTALLER’S SETTING OPTIONS 181
<Ventilation product code table>
Value 3
Setting mode
Code value
Functional product
Test Run
1
DX(Direct Exchanger) Type
Central control address setting
2
General
Air supply ESP
3
Setting value
01 : cooling operation
00~FF : central control address
<ESP stages>
01 : weak
General/DX Type
02 : strong
03 : very strong
Air discharge ESP
4
Product direction
5
h Same as general air conditioner
products’ marking.
01 : normal
General
02 : reverse
01: priority in supply,
Express ventilation priority
6
General/DX Type
02: priority in discharge
Remote controller
master/ slave setting
7
General/DX Type
00:slave, 01:master
Operation master/slave setting
8
DX Type
00:slave, 01:master
Dry contact automatic mode
9
DX Type
00:off, 01:set
Wind amount fixing
11
DX Type
01:variable, 02:fixed
Ventilation single
humidification
13
General/DX Type
Ventilation heating
humidification
14
DX Type
Ventilation standard
wind amount
15
General Type
00:function used,
01:function not used
01:automatic, 02:manual
00 : factory ship out value
11 : 10 % increase
21/22 : 10/20 % decrease
h The code value marking may be different for each product.
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 182
182 INSTALLER’S SETTING OPTIONS
INSTALLER’S SETTING OPTIONS 183
Central control address (air conditioner /General, DX type ventilator)
Test Run (air conditioner / DX(Direct Expenditure) type ventilator)
You must perform test operation after the product installation.
For details related to the trial operation, refer to the product manual.
This function allows the user to set the central control address of the indoor units during the central controller connection.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● In the Code input field, select test run code value ‘01’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● Select "02" for Code value.
- You may need to press ‘▲’, ‘▼’ button to change the code value.
● At the Value 1 field, press the ‘▲’, ‘▼’ button to select the test run mode, and press ‘Done’
button to start the test run.
- If you do not press ‘Done’ button, the setting value will not be applied.
● At the Value 1 and Value 2 fields, press the use ‘▲’, ‘▼’ button to select group address and indoor unit address value, and press ‘Done’ button to complete the address setting.
- If you do not press ‘Done’ button, your value settings will not be applied.
- Hexadecimal values, can be set from 0~F.
h Test operation mode value
- 01: cooling operation
- 02: heating operation
h Address setting
- Value 1: group number
- Value 2: indoor number
h If no buttons are pressed for about 60 seconds after the setting, it automatically exits from the
setting mode.
● During the test operation, if you operate any of the following functions, the test run will be interrupted and stop.
- Operation mode, temperature up/down, fan speed, Air flow direction, power on/off button.
ENGLISH
Test Run Operation (air conditioner / DX type ventilator)
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 184
184 INSTALLER’S SETTING OPTIONS
h ESP setting value input can be 0~255
ESP wind amount stage
wind amount
ESP wind amount stage
wind amount
01
02
03
04
05
SLOW
LOW
MED
HIGH
POWER
01
02
03
LOW
HIGH
POWER
! NOTE
• If ESP is incorrectly set, it may cause air conditioner malfunction.
• This function must be set by an installation professional.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● In the Code field, set the ESP setting value to '03'.
h For ventilation product, code values are divided to ‘03’ supply air and ‘04’ discharge air ESP
setting. Refer to the installer setting code table.
- You can press ‘▲’, ‘▼’ button to change the code value.
<Air conditioner>
<Ventilator>
! NOTE
• Be especially careful not to switch ESP values corresponding to each wind amount.
• ’SLOW’ and ‘POWER’ may not be set for some indoor unit products.
• Available ESP value may be different for each product and capacity.
Indoor temperature detection sensor setting (air conditioner)
This function select the temperature sensor to determine the indoor temperature.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● At the Code input field select indoor temperature detection sensor setting code value ‘04’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● At the Value 1 and Value 2 fields, press the, ‘▲’, ‘▼’ button to select ESP air amount stage and
ESP value, and press ‘Done’ button to apply the ESP setting.
- If you do not press ‘Done’ button, your field input value will not be applied.
h ESP setting
- Value 1: ESP fan speed step
- Value 2: ESP value
ENGLISH
ESP setting (air conditioner / Gerneral, DX type ventilator)
This function allows you to set the fan speed step value for each speed rate.
INSTALLER’S SETTING OPTIONS 185
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 186
186 INSTALLER’S SETTING OPTIONS
INSTALLER’S SETTING OPTIONS 187
Ceiling height selection (air conditioner)
This function adjusts the wind amount stages according to the ceiling height for the ceiling type
unit.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● At the Code field select ceiling height setting code value ‘05’.
- You can press ‘▲’, ‘▼’ button to change the code value.
h Sensor location setting value
- 01: remote controller
- 02: indoor unit
- 03: 2TH
Temperature sensor location
Function
Remote controller
Operate the system with wired remote
controller’s temperature sensor
Indoor unit
Operate the system with indoor unit’s temperature sensor
Cooling
Compare the temperatures of the indoor unit and the wired remote controller and operate with the higher temperature (There are system operated with lower temperature)
Heating
Compare the temperatures of the indoor unit and the wired remote controller and operate with the lower temperature
2TH
● In value1, use ‘▲’, ‘▼’ button to select ceiling height setting value, and then press ‘Done’ button to apply the ceiling height setting.
- If you do not press ‘Done’ button, your settings will not be applied.
h 2TH function’s operation characteristics may be different for each product.
h If no buttons are pressed for about 60 seconds after the setting, it automatically exits from the
setting mode.
h Ceiling height setting value
- 01: low
- 02: standard
- 03: high
- 04: very high
ENGLISH
● At the Value 1 field, press the ‘▲’, ‘▼’ button to select the sensor location setting value and
press ‘Done’ button to apply the indoor temperature detection sensor location setting.
- If you do not press ‘Done’ button, your settings will not be applied.
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 188
188 INSTALLER’S SETTING OPTIONS
INSTALLER’S SETTING OPTIONS 189
Function
Low
Fan speed operates one step slower than the default value.
Standard
Operates at the default fan speed
High
Fan speed operates one step faster than the default value.
Very high
Fan speed operates two steps faster than the default value.
● At the Value 1 field, press the ‘▲’, ‘▼’ button to select static pressure selection setting value,
and press ‘Done’ button to apply the static pressure level setting.
- If you do not press ‘Done’ button, your settings will not be applied.
h If no buttons are pressed for about 60 seconds after the setting, it automatically exits from the
setting mode.
! NOTE
• Ceiling height setting is only available for certain models.
• Some indoor units may not have a "very high" ceiling option.
• For details, refer to the indoor indoor unit’s manual.
Static pressure setting (air conditioner)
Static pressure can be set only for the duct products.
It cannot be set for other products.
h Static pressure selection setting values
- 01: V - H
- 02: F - H
- 03: V - L
- 04: F - L
Function
Static pressure
Operation region
ESP default value
Variable
High static pressure (High)
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
Variable high static pressure
V-H
● At the Code field, select static pressure setting code value ‘06’.
- You can press ‘▲’, ‘▼’ button to change the code value.
Fixed high static pressure
F-H
Fixed
High static pressure (High)
Variable low static pressure
V-L
Variable
Low static pressure (Low)
Fixed low static pressure
F-L
Fixed
Low static pressure (Low)
h If no buttons are pressed for about 60 seconds after the setting, it automatically exits from the
setting mode.
ENGLISH
Ceiling height
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 190
190 INSTALLER’S SETTING OPTIONS
This function sets configuration for the master/slave setting through the remote controller.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● At the Code field select remote controller master / slave setting code value ‘07’.
- You can press ‘▲’, ‘▼’ button to change the code value.
Remote controller
Function
Master
During the group control, the indoor units are operated based on the remote controller. (It is set as master at as shipped.)
Slave
During the group control, all remote controllers except 1 master remote controller are set as slaves.
h If no buttons are pressed for about 60 seconds after the setting, it automatically exits from the
setting mode.
Operation master / slave setting
(air conditioner / General, DX type ventilator)
This function sets the indoor unit to either slave or master mode depending on the input code
value.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● At the Value 1 field, press the ‘▲’, ‘▼’ button to select remote controller setting value, and
press ‘Done’ button to apply the remote controller master / slave selection input.
- If you do not press ‘Done’ button, your settings will not be applied.
h Remote controller setting value
- 00: slave
- 01: master
● At the Code field select operation master / slave setting code value ‘08’.
- You can press ‘▲’, ‘▼’ button to change the code value.
ENGLISH
Remote controller master / slave setting
(air conditioner / Gerneral, DX type ventilator)
INSTALLER’S SETTING OPTIONS 191
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 192
192 INSTALLER’S SETTING OPTIONS
Dry contact mode setting (air conditioner / DX type ventilator)
What is a dry contact?
It refers to the contact point signal input such as a hotel card key, human body detection sensor,
etc. is used with the air conditioner.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● Select dry contact mode setting code value ‘09’.
- You can press ‘▲’, ‘▼’ button to change the code value.
h Operation setting value
- 00: slave
- 01: master
! NOTE
Master/slave operation is not available with all products
● At the Value 1 field, press the ‘▲’, ‘▼’ button to select dry contact setting value, and press
‘Done’ button to apply the dry contact mode setting.
- If you do not press ‘Done’ button, your settings will not be applied.
h If no buttons are pressed for about 60 seconds after the setting, it automatically exits from the
setting mode.
h Operation master / slave selection function may not work in some products.
h When the slave operation function is selected, 'linked control' is displayed in the remote controller display window as in the figure below
h Dry contact setting value
- 00: manual
- 01: automatic
! NOTE
For detailed functions related to the dry contact mode, refer to the dry contact manual.
h If no buttons are pressed for about 60 seconds after the setting, it automatically exits from the
setting mode.
ENGLISH
● At the Value 1 field, press the ‘▲’, ‘▼’ button to select operation setting value, and press
‘Done’ button to apply the master / slave setting.
- If you do not press ‘Done’ button, your settings will not be applied.
INSTALLER’S SETTING OPTIONS 193
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 194
194 INSTALLER’S SETTING OPTIONS
INSTALLER’S SETTING OPTIONS 195
Celsius / Fahrenheit Switching (air conditioner)
It is the function to apply different fan speeds automatically for each thermal control status.
h Variable: When COMP is ON, operate as the set fan speed, and when COMP is OFF, operate
at ‘ROW’ fan speed.
Fixed: When COMP is ON, operate as the set fan speed, and when COMP is OFF, also operate at the set fan speed.
This function is used for switching the display between Celsius and Fahrenheit.(Optimized only
for U.S.A)
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for
3seconds or longer to enter the installer function.
● Select remote controller Celsius / Fahrenheit Switching code value ‘12’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● At the Code field select fan speed fixed setting code value ‘11’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● In value1, use ‘▲’, ‘▼’ button to select Celsius control unit setting value, and press ‘Done’
button to complete the Celsius / Fahrenheit Switching setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
● At the Value 1 field, press the ‘▲’, ‘▼’ button to select wind amount fixing setting value, and
then press ‘Done’ button to complete the fan speed fixing setting.
- If you do not press ‘Done’ button, your changes will not be applied.
h Fan speed fixed setting value
- 01: variable
- 02: fixed
h If no buttons are pressed for about 60 seconds after the setting, it automatically exits from the
setting mode.
h Celsius control unit setting value
- 000: Celsius
- 001: Fahrenjeit
h If there is no button input for about 60 seconds after the setting, it automatically exits from the
setting mode.
ENGLISH
Fan speed fixing (air conditioner / DX type ventilator)
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 196
196 INSTALLER’S SETTING OPTIONS
INSTALLER’S SETTING OPTIONS 197
Zone Number Setting(air conditioner)
This function is only available on some products.
It is possible to setup zone new type or old one of the product which is available to install the
damper controller.
This function is only available on some products.
Zone Number is to set the number of installed zones. It's possible to control only in zone new
type.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for
3seconds or longer to enter the installer function.
● Select remote controller Zone type setting code value ‘13’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for
3seconds or longer to enter the installer function.
● Select remote controller Zone Number setting code value ‘14’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● In value1, use ‘▲’, ‘▼’ button to select Celsius control unit setting value, and press ‘Done’
button to complete the Zone type setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
● In value1, use ‘▲’, ‘▼’ button to select Celsius control unit setting value, and press ‘Done’
button to complete the Zone Number setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
h Setting value
- 000 : Old
- 001 : New(4Zone)
- 002 : New(8Zone)
h Setting value
- 002~004 : Installed number(Zone type New[4Zone])
- 002~008 : Installed number(Zone type New[8Zone])
h If there is no button input for about 60 seconds after the setting, it automatically exits from the
setting mode.
h If there is no button input for about 60 seconds after the setting, it automatically exits from the
setting mode.
ENGLISH
Zone Type Setting(air conditioner)
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 198
198 INSTALLER’S SETTING OPTIONS
INSTALLER’S SETTING OPTIONS 199
Emergency Heater Setting(air conditioner)
Celsius control unit setting you to set the temperature adjustment unit in the unit of 1˚C or 0.5˚C.
This function is only available on some products
This function will set the Emergency Heater Setting.
Emergency Heater is used to heat the space in emergency case such as heat pump error.
Emergency heat is in place of and does not supplement heat pump.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● At the Code field select setting code value ‘17’.
- You can press ‘▲’, ‘▼’ button to change the code value.
h Emergency Heater setting Function sets following conditions:
1) Emergency Heater operation while in error or outdoor unit operates cooling cycle.
2) Emergency Heater operation in Low Ambient temperature
3) Fan speed setting during Emergency Heater operation
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for
3seconds or longer to enter the installer function.
● Select remote controller Emergency heater setting code value ‘18’.
You can press ‘▲’, ‘▼’ button to change the code value.
● At the Value 1 field, press the ‘▲’, ‘▼’ button to select Celsius control unit setting value, and
then press ‘Done’ button to complete the Celsius control unit setting.
- If you do not press ‘Done’ button, your changes will not be applied.
● In value1, use ‘▲’, ‘▼’ button to select Emergency heater setting value.
h Celsius control unit setting value
- 00: 1°C control
- 01: 0.5°C control
h If no buttons are pressed for about 60 seconds after the setting, it automatically exits from the
setting mode.
h Setting value #1(Heater Operation while in error or outdoor unit operates cooling cycle.)
- 000 : Not use
- 001 : Use
h If 000 is set at this stage, setting value #2 & setting value #3 will not be available.
ENGLISH
Celsius control unit setting (air conditioner)
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 200
200 INSTALLER’S SETTING OPTIONS
Setting of Function control during group control (air conditioner)
This function enables the control of the common functions or some functions based on the master indoor unit during the group control.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● At the Code field select the setting code value ‘19’ to enable function control setting during
the group control.
- You can press ‘▲’, ‘▼’ button to change the code value.
h Setting value #2(Low Ambient Heating Operation.)
- 000 : not use
- 001 : use - compressor off(0°F / -18°C) / compressor on(5°F / -15°C)
- 002 : use - compressor off(5°F / -15°C) / compressor on(10°F / -12°C)
- 003 : use - compressor off(10°F / -12°C) / compressor on(15°F / -9°C)
h Emergency heater operation in Low Ambient temperature
- Compressor off : Emergency heater enabled compressor on : Emergency heater disabled
● In value3, use ‘▲’, ‘▼’ button to select setting value.
h Setting value #2(FAN Speed Setting during Emergency Heater Operation.)
- 000 : fan off
- 001 : fan on
● Press ‘Done’ button to complete setting.
If you do not press ‘Done’ button, the setting value will not be applied.
h If there is no button input for about 60 seconds after the setting, it automatically exits from the
setting mode.
! NOTE
This function setting must be carried out by a certified-technician.
● In the Value 1 field, press the ‘▲’, ‘▼’ button set the value for the function control setting during the group control, and then press ‘Done’ button to complete the setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
h Setting values for the function control during the group control
- 00: only use common function in group control.
- 01: use expanded function which is based on master indoor unit
! NOTE
• Common functions and some indoor unit master based settings shall be set only for the
group control of the products with the same indoor unit types.
• For the group control of the product groups with different indoor unit types, set it with the
value of ‘000’ and use the existing group control method.
h If no buttons are pressed for about 60 seconds after the setting, it automatically exits from the
setting mode.
ENGLISH
● In value2, use ‘▲’, ‘▼’ button to select setting value.
INSTALLER’S SETTING OPTIONS 201
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 202
202 INSTALLER’S SETTING OPTIONS
INSTALLER’S SETTING OPTIONS 203
Indoor unit address verification (air conditioner)
This function allows you to check the address of the indoor unit designated by the outdoor unit.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● At the Code field, select the code value of the desired functional product as shown in the table
below.
- You can press ‘▲’, ‘▼’ button to change the code value.
Function
Code value
Air cleaner
20
Heater
21
Humidifier
22
Elevation grill
23
Ventilation KIT
24
Refrigerant leakage
detection sensor
29
● In the Value 1 field, press the ‘▲’, ‘▼’ button to select the setting value for each function, and
press ‘Done’ button when complete.
- If you do not press ‘Done’ button, your settings will not be applied.
h Setting value of each function
- 00: Not installed
- 01: Installed
h If no buttons are pressed for about 60 seconds after the setting, it automatically exits from the
setting mode.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● At the Code field, select the indoor unit address verification code value ‘26’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● Verify the indoor unit's setting in the Value 1 field, and press ‘Done’ button to complete the indoor unit address verification.
ENGLISH
External Devices Of Indoor Unit Setting (air conditioner)
At the Code field, select when air cleaner/heater/humidifier/elevation grill/ventilation KIT/refrigerant
leakage detection sensor are newly installed to the indoor unit or when an installed KIT is removed.
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 204
204 INSTALLER’S SETTING OPTIONS
This function using in 2 Set control mode.
This function is used for select setting temperature range option.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for
3seconds or longer to enter the installer function.
● Select remote controller temperature range setting code value ‘31’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● In value1, use ‘▲’, ‘▼’ button to select temperature range setting value, and press ‘Done’ button to complete setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
h Setting value
- 000 : 60~86 °F / 16~30 °C (default)
- 001 : 40~99 °F / 4~37.5 °C
h When the set values are changed, the items below will be initialized.
- Setting temperature (default: Cooling: 86 °F(30 °C)/ Heating: 60 °F(16 °C))
- Set back temperature (default: Cooling: 86 °F(30 °C)/ Heating: 60 °F(16 °C))
In case of the setting temperature range option2( 31:001), please note that the setting of the remote controller (with cable) can be altered under below circumstances. (Changes in setting example)
- In case of cooling at 30~37.5 °C(64~99 °F), it is changed to cooling at 86 °F(30 °C).
- In case of heating at 4~15.5 °C(40~86 °F), it is changed to heating at 60 °F(16 °C).
- If it is on the 2Set Mode, it is changed to the current operation mode(cooling or heating) of the
indoor unit.
Situation where changes in the setting occur
a. Operates the Auto address work and pipe search in situations such as product installment and
service.
b. Occurrence of errors and deactivation.
c. Command generated by the central control, outdoor unit, Dry contact, Remote controller, indoor unit switch.
ENGLISH
Setting temperature range (air conditioner)
INSTALLER’S SETTING OPTIONS 205
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 206
206 INSTALLER’S SETTING OPTIONS
INSTALLER’S SETTING OPTIONS 207
Guard timer(air conditioner)
This function is applied to only duct type. Setting this in other cases will cause malfunction.
This function is only available on some models.
This is the function that static pressure of the product is divided in 11 steps for setting.
It is a function that sets the minimum running time of outdoor unit cycle mode when switching
from cooling mode to heating mode and vice versa during Auto Operation mode.
Under the condition of cooling/heating switching, it switches between cooling and heating mode
after operation during the time scheduled in the Guard timer.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for
3seconds or longer to enter the installer function.
● Select remote controller code value ‘32’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● In value1, use ‘▲’, ‘▼’ button to select setting value, and press ‘Done’ button to complete setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
h Setting value
- 000 : use static pressure (code 06) set value.
- 001~011 : static pressure step (code 32) set value.
! NOTE
• Static Pressure (Code 06) setting will not be used if Static Pressure Step (Code 32) setting
is being used.
• For the static pressure value for each step, refer to the indoor unit in the product manual.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for
3seconds or longer to enter the installer function.
● Select remote controller code value ‘33’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● In value1, use ‘▲’, ‘▼’ button to select setting value, and press ‘Done’ button to complete setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
Value
Guard time
0
0 minute
1
15 minutes
2
30 minute
3
45 minutes
4
60 minutes
ENGLISH
Static Pressure Step Setting(air conditioner)
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 208
208 INSTALLER’S SETTING OPTIONS
It is a function that sets the indoor unit fan movement, in cooling mode, when thermal is off.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for
3seconds or longer to enter the installer function.
● Select remote controller code value ‘35’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● In value1, use ‘▲’, ‘▼’ button to select setting value, and press ‘Done’ button to complete setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
Value
0
Fan operation in the cooling mode
and thermal off conditions
Fan speed Low
1
Fan off
2
Fan speed Setting value
Primary Heater control setting(air conditioner)
It is a function that sets the outdoor unit to operate with auxiliary heat source and the heater to
run with main heat source in heating mode.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for
3seconds or longer to enter the installer function.
● Select remote controller code value ‘36’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● In value1, use ‘▲’, ‘▼’ button to select setting value, and press ‘Done’ button to complete setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
Value
Primary Heater control setting
000
Cancel primary heater control
001
Use primary heater control
ENGLISH
Fan operation in the cooling mode and thermal off conditions
(air conditioner)
INSTALLER’S SETTING OPTIONS 209
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 210
210 INSTALLER’S SETTING OPTIONS
It is a function that sets the availability of air conditioner FAN movement when only the ventilation is running while air conditioner is off, in case of interlock of the air conditioner operation with
the ventilation operation.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for
3seconds or longer to enter the installer function.
● Select remote controller code value ‘38’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● In value1, use ‘▲’, ‘▼’ button to select setting value, and press ‘Done’ button to complete setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
Indoor unit Auto-Start setting(air conditioner)
It is a function that sets whether to restore the indoor unit operation by resuming the previous
power-on state or as power-off state in the power failure compensation.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for
3seconds or longer to enter the installer function.
● Select remote controller code value ‘39’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● In value1, use ‘▲’, ‘▼’ button to select setting value, and press ‘Done’ button to complete setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
Value
Value
Primary Heater control setting
Primary Heater control setting
000
air-conditioner fan off
001
air-conditioner fan operate very low
000
Use indoor unit auto restart
001
Not use indoor unit auto restart
ENGLISH
Air conditioner Fan operation interlocked with ventilation
(air conditioner)
INSTALLER’S SETTING OPTIONS 211
1.MFL69279715,영영 2016. 3. 15. 영영 10:45 Page 212
212 INSTALLER’S SETTING OPTIONS
INSTALLER’S SETTING OPTIONS 213
Setting for Simple Dry contact unit
It is a function that sets the light-on/occupancy duration after motion is detected when installing
an occupancy sensor.
This function is used when simple dry contact unit is additionally installed in the indoor unit or the
installed simple dry contact unit is removed.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for
3seconds or longer to enter the installer function.
● Select remote controller code value ‘40’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● Select remote controller code value ‘41’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● In value1, use ‘▲’, ‘▼’ button to select setting value, and press ‘Done’ button to complete setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
Value
Occupancy Duration Time
000
0 minute
001
10 minutes
002
30 minutes
003
60 minutes
● In value1, use ‘▲’, ‘▼’ button to select setting value, and press ‘Done’ button to complete setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
ENGLISH
Occupancy Duration Time Setting(air conditioner)
1.MFL69279715,영영 2016. 3. 15. 영영 10:46 Page 214
214 INSTALLER’S SETTING OPTIONS
Setting for Simple Dry contact unit
000
Default – Simple Dry contact Auto identification
001
Simple Dry contact : Not installed
002
Simple Dry contact : Installed
003
Use for digital input
Product direction (General ventilator)
It is the function to set the direction of the ventilation product.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● Select remote controller Celsius control unit setting code value ‘05’.
- You can press ‘▲’, ‘▼’ button to change the code value.
h If there is no button input for about 60 seconds after the setting, it automatically exits from the
setting mode.
h DI/DO may not work in some indoor unit products.
● In value1, use ‘▲’, ‘▼’ button to select product direction setting value, and press ‘Done’ button
to complete the setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
h Product direction setting value
- 01: normal
- 02: reverse
h If there is no button input for about 60 seconds after the setting, it automatically exits from the
setting mode.
ENGLISH
Value
INSTALLER’S SETTING OPTIONS 215
1.MFL69279715,영영 2016. 3. 15. 영영 10:46 Page 216
216 INSTALLER’S SETTING OPTIONS
INSTALLER’S SETTING OPTIONS 217
Humidification of Stand-alone Ventilation mode (General, DX type ventilator)
It is the function to set whether to use the humidification function during the ventilation product
single operation.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● Select remote controller Celsius control unit setting code value ‘06’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● Select remote controller Celsius control unit setting code value ‘13’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● In value1, use ‘▲’, ‘▼’ button to select express ventilation priority setting value, and press ‘Finish’ button to complete the setting.
- If you do not press ‘Finish’ button, the setting value will not be applied.
● In value1, use ‘▲’, ‘▼’ button to select ventilation single humidification setting value, and
press ‘Done’ button to complete the setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
h Express ventilation priority setting value
- 01: priority in air supply
- 02: priority in air discharge
h Ventilation single humidification setting value
- 01: Used
- 02: Not used
h If there is no button input for about 60 seconds after the setting, it automatically exits from the
setting mode.
h If there is no button input for about 60 seconds after the setting, it automatically exits from the
setting mode.
ENGLISH
Express ventilation priority (General, DX type ventilator)
It is the function to set the priority of the air supply and air discharge during the express ventilation operation.
1.MFL69279715,영영 2016. 3. 15. 영영 10:46 Page 218
218 INSTALLER’S SETTING OPTIONS
INSTALLER’S SETTING OPTIONS 219
Ventilator Fan Speed Alignment (General ventilator)
It is the function to change the standard fan speed of the ventilation product.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● Select remote controller Celsius control unit setting code value ‘14’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● In value1, use ‘▲’, ‘▼’ button to select ventilation heating humidification setting value, and
press ‘Done’ button to complete the setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
h Ventilation single humidification setting value
- 01: Used
- 02: Not used
h If there is no button input for about 60 seconds after the setting, it automatically exits from the
setting mode.
● Press and hold ‘wireless remote controller signal receiver part’ of the remote controller for 3
seconds or longer to enter the installer function.
● Select remote controller Celsius control unit setting code value ‘15’.
- You can press ‘▲’, ‘▼’ button to change the code value.
● In value1, use ‘▲’, ‘▼’ button to select ventilation standard fan speed setting value, and press
‘Done’ button to complete the setting.
- If you do not press ‘Done’ button, the setting value will not be applied.
h Ventilation standard wind amount setting value
- 00: factory ship-out
- 01: 10% increase
- 21: 10% decrease
- 22: 20% decrease
h If there is no button input for about 60 seconds after the setting, it automatically exits from the
setting mode.
ENGLISH
Humidification Of Ventilation With Heating Operation (DX type ventilator)
It is the function to set the heating humidification function of the direct ventilation to be automatic or manual.
1.MFL69279715,영영 2016. 3. 15. 영영 10:46 Page 220
220
221
ENGLISH
1.MFL69279715,영영 2016. 3. 15. 영영 10:46 Page 222
Download PDF

advertising