LG | LAC7700R | Owner's Manual | LG LAC7700R Owner's manual

LG LAC7700R Owner's manual
LAC7700R_ENG_MOSCOW
ENGLISH
CAR CD/MP3/WMA Receiver
OWNER’S MANUAL
MODEL : LAC7700R
Please read this instruction booklet carefully
and completely before installing, operating or
adjusting this product.
The working life of this product is 7 years since
the data of purchase.
Safety note
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT SPLIT COVER(OR BACK) NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with the arrowhead symbol, within an equilateral
triangle is intended to alert the user about the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
Always operate the vehicle in a safe manner.
Do not become distracted by the vehicle while driving, and always be fully
aware of all driving condition. Do not change settings, or any functions.
Pull over in a safe and legal manner before attempting such operations.
Do not use for many hours at extremely low or high temperature.
(-10~60°C)
To reduce the risk of electric shock, do not remove the cover or back of
this product. There are no user-serviceable parts inside.
Refer servicing to qualified service personnel.
To reduce the risk of fire or electric shock, do not expose this product to
dripping or splashing water, rain, or moisture.
The temperature of unit’s outside can be extremely high, please use the
unit after proper installation in your vehicle.
CAUTION : This product uses a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully
and retain it for future reference. Should the unit require maintenance, contact an
authorized service center.
Performing controls, adjustments, or carrying out procedures other than those
specified herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible laser radiation when open. DO NOT STARE INTO BEAM.
2
Safety note
• A defective or soiled disc inserted into unit can cause sound to drop out
during playback.
• Handle the disc by holding its inner and outer edges.
• Do not touch the surface of the unlabeled side of the disc.
Do not stick paper or tape etc. on the surface.
Do not expose the disc to direct sunlight or excessive heat.
8 cm
This unit cannot play 8cm disc (use 12cm disc only).
• Clean the disc before playback. Wipe the disc from the center outward
with a cleaning cloth.
• Never use solvents such as benzine or alcohol to clean the disc.
Periodically wipe the contacts on the back of the control panel with a
cotton swap moistened with alcohol.
Bluetooth® wireless technology is a system which allows radio contact
between electronic devices within a max. range of 10 meters.
Connecting individual devices under Bluetooth® wireless technology does
not incur any charges. A mobile phone with Bluetooth® wireless
technology can be operated via the Cascade if the connection was made
via Bluetooth® wireless technology.
Operating condition for using a Bluetooth function
- Close windscreen.
- Turn off the air conditioner/ heater.
- Stop the vehicle or drive at low speed.
- Make the call in a quiet location.
• There may be differences in call quality depending on phone type, road
conditions weather, etc.
• Using the phone while driving may cause unexpected accidents.
• The Bluetooth function may not operate properly with certain types of
Bluetooth phones.
3
Table of contents
Safety note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14
Bluetooth operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-19
Radio operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RDS operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
CD/MP3/WMA operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23
Aux operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Bluetooth phone compatibility list. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
A section whose title has one of the following symbols is applicable only to
the disc represented by the symbol.
CD
MP3
Audio CDs
MP3 files
WMA WMA files
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product, it means the
product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the
municipal waste stream via designated collection facilities appointed by the
government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please
contact your city office, waste disposal service or the shop where you purchased
the product.
This product is manufactured to comply with Directive 2005/83/EEC(ANNEX I ,
3.2.9), 72/245/EEC, and 2006/95/EC.
4
Before use
Detaching the control panel
You can detach the control panel when leaving the car.
When detaching or attaching the control panel, be careful not
to damage the connectors on the back of the control panel
and on the panel holder.
1.
2.
3.
4.
2
3
Press the “ ” button to unlock the control panel.
Push the control panel to right.
Pull the control panel out of the unit.
Put the detached control panel into the protective case.
Protective Case
4
Control panel
Attachable control panel
1
2
3
Attach part A of the control panel to part B of the unit.
Attach part C of the control panel to part D of the unit
while pushing the control panel to right.
Close the control panel.
Caution
• When detaching or attaching the control panel, do not press
the display or control buttons.
• The control buttons may not work properly if the control
panel is not attached properly. If this occurs, gently press the
control panel.
• Do not leave the control panel in any area exposed to high
temperatures or direct sunlight.
• Do not drop the control panel or otherwise subject it to strong
impact.
• Do not allow such volatile agents as benzine, thinner, or
insecticides to come into contact with the surface of the
control panel.
• Do not try to disassemble the control panel.
5
B
D
C
A
Control Panel
1
2
17
3
4
16
1
2
[SOURCE]
i
• Skip / Search I/i
• Seek/ Tune
• Auto Store [AS]
• Preset Scan [PS]
u MP3 WMA
• MP3 Track +10/-10 U/u
u MP3 WMA
• Folder Up/Down U/u
3
4
Remote Sensor
• Volume [VOL.]
• [MUTE]
• Power [PWR]
• Traffic Announcement [TA]
• Programme Type [PTY]
• Equalizer [EQ]
• Extreme Dynamic Sound System
[XDSS]
• Bass Reverb Blaster [BRB]
Display [DISP]
Release/Eject
5
6
7
8
5
15
14
13
9
10
11
12
13
14
15
16
12
11
AUX In [AUX]
Preset Station [1~6]
Shuffle [SHF]
Repeat [RPT]
Intro Scan [SCAN]
Play/Pause B/X
[BAND]
• [MENU]
• Select [SEL]
17 Bluetooth [B/T]
6
6
10
7
8
9
Remote control
1
2
3
4
5
6
7
Power [POWER] / Mute
Select [MENU/SEL]
Source [SRC]
Play / Pause B/X
Intro Scan [SCAN]
Shuffle [SHF]
• MP3 Track +10 MP3 WMA
• Folder Up U MP3 WMA
8 • CD Skip / Search ?m m
• Seek / Tune ?m m
9 [BAND]
10 Volume Up
/ Down
1
2
3
4
Number [#]
Repeat [RPT]
Number [0 -9]
• CD Skip / Search M M?
• Seek / Tune M M?
15 Display [DISP.]
16 • MP3 Track -10 MP3 WMA
• Folder Down u MP3 WMA
Battery installation
2
3
11
12
5
6
7
13
8
14
9
15
16
11
12
13
14
1
10
Remove the battery holder with a sharp product like a ball
point pen.
Install the battery on the battery holder.
Install the battery holder back into its original position.
Note
• Use only one CR2025 (3V) lithium battery.
• Remove the battery if the remote control is not used for a
long period of time.
• Do not leave the product in a hot or humid place.
• Do not handle the battery with metallic tools.
• Do not store the battery with metallic materials.
7
Installation
Basic Installation
Before installing, make sure that the ignition-switch is set to
OFF and remove the terminal of the car battery to avoid
short-circuiting.
Bend the claws
according to
the thickness
of the
dashboard
1
2
3
4
Remove the existing receiver unit.
Make the necessary connections.
Install the installation sleeve.
Install the unit into the installation sleeve.
Control panel
Removing the existing receiver unit.
If there is already an installation sleeve for the receiver unit in
the dashboard, it must be removed.
A
1
2
3
A
Remove the rear support from the unit.
Remove the control panel and trim ring from the unit.
Insert the lever A into the hole on one side of the unit.
Perform the same operation on the other side and pull the
unit out from the mounting sleeve.
ISO-DIN Installation
1
4
5
6
3
2
1
2
3
4
5
6
Slide the unit into the ISO-DIN frame.
Fit screws removed from the old unit.
Slide the unit and frame into the dash opening.
Install the dash panel or adapter plate.
Install the trim ring to the unit.
Install the control panel to the unit.
Control panel
8
Connection diagram
Before connecting, make sure that the ignition switch is set to OFF, and remove the battery #
terminal to avoid short circuits.
B
A
B
A
1
3
5
7
2
4
6
8
1
3
5
7
2
4
6
8
Microphone Plug
To Speaker
To Vehicle
A
2
PHONE MUTE (ORANGE)
A
8
GROUND(-) (BLACK)
A
6
DIMMER (PINK)
A
DIMMER SWITCH
7
TO IGNITION (RED)
IGNITION SWITCH
A
4
TO BATTERY(+) (YELLOW)
A
5
POWER ANTENNA (BLUE)
A
1
1
AMPLIFIER
(Optional)
BATTERY
2
REMOTE ON (BLUE/WHITE)
3
POWER
Antenna
4
5
CONTROL RELAY
6
7
8
B
B
B
B
B
B
B
B
1.
2.
3.
4.
5.
6.
7.
8.
Violet : Rear Right +
Violet/ Black Stripe : Rear Right –
Gray : Front Right +
Gray / Black Stripe : Front Right –
White : Front Left +
White/Black Stripe : Front Left –
Green : Rear Left +
Green/ Black Stripe : Rear Left –
9
C
Connection
C Speaker Connections A From antenna
B To the wiring of the vehicle colors of leads.
1
2
3
4
5
6
7
8
L
• BLACK
: This lead is for the ground connection.
• ORANGE
: This lead is for the phone line connection.
• PINK
: This lead is for the dimmer line
connection.
• RED
: This lead is for connection to the power
supply terminal when the ignition switch is
set to ACC.
• YELLOW
: This lead is for connection to the battery
(back-up) terminal from which power is
always supplied.
• BLUE
: This lead is for the power antenna
connection.
REAR
L
FRONT
R
• BLUE/WHITE : This lead is for the remote amplifier on
connection.
FRONT
R
REAR
Connecting to Auxiliary Equipment (Optional)
Connect the AUDIO OUTPUT jack of this unit to the AUDIO
INPUT jack of the Auxiliary Equipment.
FL (Front Left)
RL (Rear Left)
FR (Front Right)
RR (Rear Right)
Microphone
To AUDIO OUT
To AUDIO IN
To AUDIO IN
Microphone Plug
With the sun visor up, install the microphone.
Amplifier
10
Basic operation
Turning the unit on
Press VOL./MUTE/PWR (POWER/
on the remote control) or any other button.
Note
When you insert the CD in the CD slot, the unit turns on.
Turning the unit off
Press and hold VOL./MUTE/PWR (POWER/
on the remote control).
Insert a disc
1
2
Press
to open the control panel.
Draws the disc, and starts playback automatically.
Eject a disc
Press
to open the control panel. The disc automatically ejects from the loading slot.
When the disc is ejected by pressing
during playback, it will be loaded automatically after
10 seconds unless you pull out disc from the unit.
Selecting a source
Press SOURCE repeatedly to select a source.
The indicator lights up in the following order. TUNER → CD → AUX → TUNER...
Note
You cannot select a source if is not ready.
Adjusting the volume
Rotate VOL./MUTE/PWR (Press VOLUME
level.
on the remote control) to adjust the sound
Note
When you turn the unit off, the current volume level is automatically memorized. Whenever
you turn the unit back on, it will operate at the memorized volume level.
Mute
1
2
Press VOL./MUTE/PWR (POWER/MUTE
To cancel it, press again.
on the remote control) to cut the sound.
Checking the clock
You can see the clock pressing DISP (DISP. on the remote control).
11
Basic operation
Changing the general settings
1
2
3
4
Press and hold MENU/SEL (MENU/SEL on remote control) so that one of menu items
appears.
Press MENU/SEL (MENU/SEL on remote control) to scroll between menus.
AF ON t REG ON t TA ALARM t PI SOUND t AUX ON t AUX 00dB t
DEMO ON t BEEP 2ND
Rotate VOL./MUTE/PWR clockwise or unclockwise to select one of the settings specified
belows.
(Press VOLUME
on the remote control.)
Press and hold MENU/SEL (MENU/SEL on remote control) to finish the setting.
AF(Alternative frequency) ON / OFF
When the reception quality drops, the tuner automatically changes to another station in the
network, broadcasting a better reception quality, using the PI and AF codes.
AF ON :
wherever you drive, you can continue to listen to the same program without interruptions.
AF OFF :
Only station name will be displayed. In case of poor reception no alternative station can
be used.
REG (Region) ON / OFF
REG ON :
The unit switches to another station, within the same network, broadcasting the same
program when the receiving signals from the current station become weak.
REG OFF :
The unit switches to another station, within the same network when the receiving signals
from the current station become weak. (This mode, the program may differ from the one
currently received.)
TA(Traffic Announcement) ALARM / SEEK
TA ALARM :
When a newly tuned station has no TP information for 5 seconds, a double beep sound is
output.
TA SEEK :
When the newly tuned station does not receive TP information for 5 seconds, the receiver
retunes to the next station which has the same PI as the last station, but has the TP
information.
PI (Programme Identification) SOUND / MUTE
PI SOUND :
If the sound of a station with different PI is heard intermittently, the receiver mutes the
sound after 1 second.
PI MUTE :
If the sound of a station with different PI is heard intermittently, the receiver mutes the
sound right now.
12
Basic operation
AUX (Auxiliary) ON / OFF
It is possible to use auxiliary equipment with this unit. Activate the auxiliary setting when
using auxiliary equipment connected to this unit.
AUX ON
When using a auxiliary equipment.
AUX OFF
When not using a auxiliary equipment.
AUX (Auxiliary) 00dB / +6dB
You can adjust the volume level of each source to prevent radical changes in volume when
switching between sources.
You can set to 0 dB or +6 dB
If the input level of the connected component is not high enough, increase the input level
properly. Without adjusting the line input level, you may be surprised at a loud sound when
you change the source from the external component to another source.
DEMO ON / OFF
You can change the initial indication on the display to information name (function name,
EQ name, etc...) while listen to a source.
DEMO ON
Displays information name while listening to source.
DEMO OFF
Cancels the function.
BEEP 2ND / ALL
Sets the beep sound every time a button is pressed.
BEEP 2ND
The beep is generated when a key is long pressed. (1 sec)
BEEP ALL
The beep is generated when any key is pressed.
Using the EQ (Equalizer)
Press EQ/XDSS/BRB repeatedly. The indicator lights up in the following order.
Pop t Classic t Rock t Jazz t Vocal t Salsa t Samba t User1 t User2 t Off
• Pop
: Optimized for R&B, Soul and Country music.
• Classic
: Optimized for orchestral music.
• Rock
: Optimized for Hard Rock and Heavy Metal music.
• Jazz
: Sweet sound with soft feeling.
• Vocal
: Powerful realism with strong sound quality.
• Salsa
: Reproduces salsa music acoustics.
• Samba
: Reproduces samba music acoustics.
• User1
: Use the menu to set the sound level you want.
• User2
: Use the menu to set the sound level you want.
You can adjust each sound level to your preference. Once you select a USER mode and then
make an adjustment, it automatically stored for the currently selected USER mode.
Refer to the “Adjusting the sound level” on the page 14.
13
Basic operation
Adjusting the sound level
1
2
Press MENU/SEL (MENU/SEL on the remote control) repeatedly to select the mode you
want to adjust from volume, bass, middle, treble, balance and fader.
The indicator lights up in the following order.
VOL t BAS t MID t TRB t BAL t FAD
Rotate the VOL./MUTE/PWR. (Press VOLUME
on the remote control) to adjust the
sound quality.
Indication
Turn right
Turn left
VOL
BAS
Increase the volume level.
Decrease the volume level.
Increase the bass level.
Decrease the bass level.
MID
TRB
BAL
Increase the middle level.
Decrease the middle level.
Increase the treble level.
Decrease the treble level.
Decrease the level of the left speaker(s).
Decrease the level of the right speaker(s).
FAD
Decrease the level of the front speaker(s).
Decrease the level of the rear speaker(s).
Note
When EQ, BRB or XDSS+ is set to “Off”, you can adjust the sound level (BAS, MID, TRB)
settings.
XDSS+ (Extreme Dynamic Sound System)
1
2
Press and hold EQ/XDSS/BRB.
Each time you press and hold the button, the modes change as follows.
XDSS+ t BRB (TBB t 3D t SBB)
XDSS+ : Improve the treble, bass sound.
BRB (Bass Reverb Blaster)
1
2
3
Press and hold EQ/XDSS/BRB.
Each time you press and hold the button, the modes change.
Press EQ/XDSS/BRB repeatedly to select sub BRB.
• TBB (Turbo-Bass Blaster) : Improve the bass sound to make it spectacular.
• 3D (3D-TremD Blaster) : Positions audio effects real time in 3D space.
• SBB (Sound field Boost Blaster) : Extremely wide stereo imaging and improved low
frequency bass.
14
Bluetooth operation
Using a Bluetooth wireless connection
Your unit supports Bluetooth wireless connections. You can set up
a wireless link with Bluetooth phone.
Starting Bluetooth on your phone
Your phone’s Bluetooth feature may be set to off by default.
To use your car Bluetooth feature, Bluetooth must be turned on in
your phone.
Note
Refer to your phone’s user guide.
Pairing your unit and Bluetooth phone
Pairing links your unit and Bluetooth phone, and is required only once for the initial setup.
Before you start the pairing procedure, make sure the Bluetooth feature is turned on in to
your Bluetooth phone. Refer to your Bluetooth phone’s user guide.
1
2
3
4
5
6
7
8
Press and hold B/T to connect your Bluetooth phone.
If connecting through a Bluetooth phone, the handsfree connection or headset
connection may operate depending on the type of phone.
With connection via Bluetooth technology, HFP (Hands Free Profile) is prioritized over
HSP (Head Set Profile).
The unit displays the PIN code enter screen. PIN : 1234
The unit may request permission to bond with your phone.
The
indicator flashes.
To cancel, press and hold B/T again.
You can set up a wireless link with Bluetooth phone.
Refer to your phone’s user guide.
The Bluetooth phone displays the device name, select the device.
The Bluetooth phone displays the PIN code enter screen, enter the PIN code 1234.
If the connection is successful, the Bluetooth phone is registered (Device 1–5).
When your unit successfully paired with your Bluetooth phone, the flashing of indicator
stops.
Note
• Your unit keeps lists of pairing you recently connected. A maximum of 5 pairing numbers
can be saved.
• Unlike the Hands-free functionality, Headset connection will allow only two functions
“answering calls” and “making a call from the latest call”.
15
Bluetooth operation
Changing the Bluetooth settings
1
2
3
4
Press B/T so that one of menu items appears.
Press U/AS or u/PS to scroll between menus.
Connection y BT Setting
Press B/T to enter the “BT Setting” menu.
Press U/AS or u/PS up or down to scroll between sub menus.
Auto Connection On y Auto Answer On y HF VOL
5 Press I or i left or right to select the settings of your choose.
Auto Connection On / Off
ON :
Bluetooth phone with a previous record showing that it has successfully connected will
automatically start the connection process when starting the car.
OFF :
Cancels the function.
Auto Answer On / Off
ON :
If you set the automatic answering function on, hands-free answering call is possible.
OFF :
Cancels the function.
HF VOL (Setting range : 0~35)
After connected, it is necessary to adjust the volume of Bluetooth’s voice.
It is possible to adjust the volume using the VOL./MUTE/PWR button when talking on the
phone.
Connecting a Bluetooth phone
After being registered, it is necessary to connect your Bluetooth phone from this unit.
1
2
3
Press B/T to enter the “Connection” menu.
Press B/T to connect a Bluetooth phone to this unit.
The message “Connect?” is displayed.
Press B/T again.
While connecting, the “Connected” is displayed.
Note
Your unit keeps lists of pairing you recently connected. A maximum of 5 pairing numbers can
be saved.
Disconnecting a Bluetooth phone
It is possible to disconnect your Bluetooth phone from this unit.
1
2
3
Press B/T so that one of menu items appears.
Press U/AS or u/PS up or down to select the message “Discon?”.
Press B/T to disconnect a Bluetooth phone from the unit.
16
Bluetooth operation
Answering and Ending a call
Your unit, Bluetooth phone, or both may ring when you receive a call, press B/T to answer a
call. To end a call, press and hold B/T.
Note
If the Call-ID service is available, the caller’s phone number is displayed.
Rejecting a call
When your unit rings, press and hold B/T.
Note
If “REJECT” function is unusable, then the phone connected to the device does not support
the reject call function.
Missed call notification
When an incoming call is not answered, the missed call message is displayed on the your
screen.
1
2
3
4
The “
” appears on the screen.
Press B/T to place a call.
Press B/T to place a call to entered phone number.
To end the call and hang up the phone, press and hold B/T button.
Auto transfer
It is possible to select the automatic connection between your Bluetooth phone and this unit.
1 Press B/T to answer the call.
2 Press B/T again.
The “Private” is displayed.
If the private mode is selected on the unit, press B/T to return to the call to hands-free
mode. (This feature is only available on phones with Hands-free profile.)
Or press and hold B/T to return to the call to hands-free mode. (This feature is only
available on phones with Headset profile.)
Making a call from the latest call : Last call?
Your phone keeps a lists of your recently received and dialed even if the calls did not
connected. The lists are sorted from newest to oldest entries.
Your unit keeps recorded of your recently received and dialed on phone.
1
2
Press B/T to place a call.
Press B/T to place a call to entered phone number.
The “Calling” appears on the screen.
There is case that sending is done by pressing B/T button for a long time depending on
type of Bluetooth phone. (For basic setting, press B/T button shortly.)
Note
• When you want to make an international call, press i to add “+”.
Press I to delete ” +”.
• “+” can only be added when the detail list of Missed call, Dialled call or Received call is
selected.
17
Bluetooth operation
Dial using a number from the last answered :
Your unit keeps a record of your recently received and display.
1
2
3
Press B/T to enter the menu.
Press U/AS or u/PS up or down to select the call number.
Press B/T to place a call to entered phone number.
The “Calling” appears on the screen.
Note
• When you want to make an international call, press i to add “+”.
press I to delete ” +”.
• “+” can only be added when the detail list of Missed call, Dialled call or Received call is
selected.
Storing a call number in last answered.
If you press any of the preset button 1~6, you can easily store up to 6 phone numbers and
laster recall with the press the button.
1
2
3
4
Press B/T to enter the menu.
Press U/AS or u/PS up or down to select the call number.
Press one of preset buttons 1~6 and hold until the beep sound.
The “Save to..” appears on the screen.
The selected phone number has been stored in memory.
The next time, you press the same preset button, the phone number is recalled from
memory.
Making a call from the preset list
It is possible to make a call from the preset phone number list.
1
2
3
Press B/T to enter the menu.
Press the preset button 1~6, the phone number is recalled from memory.
Press B/T to place a call.
Paring your unit and Bluetooth device (MP3 Player, MP3 Phone...)
When you activate your Bluetooth device’s linked unit, you can listen to MP3 with wireless
connections.
The method of use for a Bluetooth device is the same as when using a Bluetooth phone.
- Refer to the page 15 for details.
Playing MP3 files
When you turn Bluetooth on, your Bluetooth device displays “Bluetooth” on the home screen.
The Bluetooth remains on until you turn the device off.
Press SOURCE repeatedly to select Bluetooth.
The indicator lights up in the following order.
TUNER → CD → AUX → BT → TUNER...
To play an MP3 file stored on your Bluetooth device, refer to your Bluetooth device’s user guide.
18
Bluetooth operation
Bluetooth Profiles
In order to use Bluetooth technology, devices must be able to interpret certain profiles.
This unit is compatible with following profiles.
GAP (Generic Access Profile)
HSP (Hands Set Profile)
HFP (Hands Free Profile)
GAVDP (Generic Audio/Video Distribution Profile)
A2DP (Advanced Audio Distribution Profile)
AVDTP (Audio/Video Distribution Transport Profile)
AVRCP (Audio/Video Distribution Remote Control Profile)
GAP
GAP is short for Generic Access Profile. This is a basic profile of Bluetooth wireless
technology.
HFP
HFP is short for Hands-Free Profile. This profile is used for hands-free phoning with the
devices featuring Bluetooth wireless technology.
HSP
HSP is short for Head Set Profile. This profile is used for connecting a headset and
for communicating terminal wireless technology.
GAVDP
This profile uses an Initiator (INT), a device (such as a portable player) that initiates a
signalling procedure to send a request to an Acceptor (ACP), - such as headphones etc.
Although this profile specifies signalling transaction procedures between two devices to set
up, terminate and reconfigure streaming channels, using GAVDP alone, it is required to use
GAVDP in combination with profiles that depend on this profile - the AVRCP and the VDP.
A2DP
Mobile phones and devices with A2DP high quality stereo bluetooth profile.
This profile is based on the GAVDP, and allows advanced audio to be transmitted (audio
streaming) from a Source (SRK) - such as a CD player, to a Sink (SNK), such as
headphones.
AVRCP
Based on the GAP Profile, this uses a Controller (CT) - PDA, computer mobile phone etc.,
which sends a command to a Target (TG) - TV, discman, headphone etc. The command can
be to Play, record, colour control, volume control etc., depending on the nature of the devices
involved and the scenario. The commands are transported by a new additional protocol,
called the Audio/Video Control Transport Protocol (AVCTP). Some scenarios defined are
Remote Control from a Separate Controller, Remote Control and Audio Stream Between Two
Devices, and Remote Controller with LCD.
19
Radio operation
Listening to radio stations
1
2
3
Press SOURCE to select the tuner.
Press the BAND repeatedly to select a band.
The indicator lights up in the following order. FM1 t FM2 t FM3 t MW(AM)
Auto Search : Press I/i (?m m/M M? on the remote control).
When a station is received, searching stops.
Manual Search : Press and hold I/i (?m m/M M? on the remote control) until
“MANUAL” appears, and then press it repeatedly.
The frequencies move up or down step by step.
Storing and recalling broadcast frequencies
You can easily store up to 6 broadcast frequencies for later recall at the touch of a button.
1
2
3
4
Press BAND to select desired band you want to store.
Select the desired frequency.
Press one of preset buttons 1~6 and hold until the beep sound.
The number you have pressed will flash in the preset number indicator and then remain
lit. The selected radio station frequency has been stored in memory.
Repeat steps 1 ~ 3 to preset other stations.
The next time, you press the same preset button, the radio station frequency is
recalled from the memory.
Note
• Up to 18 FM stations, 6 for each of three FM bands and 6 MW(AM) stations can be stored
in the memory.
• When a station is stored on the preset numbers on which another station of the same band
has already been preset, the previously preset station is automatically erased.
Auto search memory
This function lets you automatically store the 6 strongest broadcast frequencies.
1
2
Press U/AS until “AUTO STORE” appears.
The six strongest broadcast frequencies will be stored under preset button 1~6 in the
order of their signal strength.
To cancel, press U/AS.
To scan the preset stations
Press u/PS. Each preset station appears. To cancel, press u/PS.
To tune in the preset stations
Press BAND to select the desired band and press the desired preset button 1~6.
The preset station of the preset button 1~6 is displayed and the preset station is received.
20
RDS operation
RDS Display options
In normal RDS operation the display will indicate the station name. Pressing DISP
enables you to cycle through the various data types in the following sequence:
CT t FREQUENCY t PTY t RT t PS
• CT (Time controlled by the channel)
• PTY (Programme type recognition)
• RT (Radio text recognition)
• PS (Programme Service name)
• PI (Programme Identification)
• AF (Alternative Frequencies for the actual programme)
• TP (Traffic programme Identification)
• TA (Traffic Announcement Identification)
PTY (Programme Type) function
To select a certain program type out of the reception band, the following procedure can be
used.
1 Press and hold TA/PTY to select a programme types.
2 After, press and hold TA/PTY repeatedly for selecting each mode.
Music group t Speech group t Search off
3 Press one of preset buttons 1~6
Each time this button is pressed, the display mode changes as follows.
No
Music group
No
Speech group
1.
2.
3.
4.
5.
6.
Pop M, Rock M
Easy M, Light M.
Classics, Other M
Jazz, Country
Nation M, Oldies
Folk M
1.
2.
3.
4.
5.
6.
News, Affairs, Info
Sport, Educate, Drama
Culture, Science, Varied
Weather, Finance, Children
Social, Religion, Phone In
Travel, Leisure, Document
Note
RDS is only available for FM reception.
TA (Traffic Announcement) function
TA reception allows the unit to switch temporarily to a Traffic Announcement from the current
source (another FM station, CD, or other connected components).
To switch the TA (Traffic Announcement) function on or off, press TA/PTY.
• TA ON
Traffic programs and announcements can be automatically received using TP/TA features.
• TA OFF
Traffic programs and announcements can not be received using TP/TA features.
21
CD/MP3/WMA operation
Playing an Audio CD and MP3/WMA Disc
The unit can play MP3/WMA formatted recordings on CD-ROM, CD-R or CD-RW discs.
Before playing MP3/WMA recordings, read the notes on MP3/WMA Recordings on page 26.
If you change the source, CD play also stops (without ejecting the CD). Next time you select
“CD” as the source, CD play starts from where playback has been stopped previously.
To directly play a file, press NUMBER (#) on remote control and then press the track
number with 0-9 number.
Pause
CD
MP3
WMA
1 Press B/X during playback.
2 To return to playback, press B/X again.
Skip to next track/file
CD
MP3
WMA
Press briefly i (M M? on the remote control) to select the next track or file.
Skip to previous track/file
CD
MP3
WMA
Press briefly I (?m m on the remote control) within 3 seconds of playing time.
Return to the beginning of the current track/file
CD
MP3
WMA
Press briefly I (?m m on the remote control) after 4 seconds of playing time.
Search
CD
MP3
WMA
Press and hold I/i (?m m/M M? on remote control) for about 1 second during
playback and then release at the point you want.
Intro scan
The first 10 seconds of each tracks/files (SCAN) or each files in the current selected folder
(
SCAN) on the disc are played.
1
2
Press SCAN.
–
SCAN MP3 WMA (or SCAN CD ) appears on the display window.
Press and hold SCAN for about 2 seconds during playback.
– SCAN appears on the display window. MP3 WMA
Press SCAN again.
– SCAN or
SCAN disappear from the display window and The intro scan is cancelled.
Repeat
The current selected tracks/files (1 RPT) or folder (
1
2
3
RPT) on the disc is played repeatedly.
Press RPT during playback.
– 1 RPT appears on the display window. CD MP3 WMA
Press and hold RPT for about 2 seconds during playback.
–
RPT appears on the display window. MP3 WMA
Press RPT again.
– 1 RPT or
RPT disappear from the display window and the repeat mode is cancelled.
22
CD/MP3/WMA operation
Shuffle
All of the tracks/files (SHF) or the current selected folder (
SHF) on the disc is played
randomly.
1 Press SHF during playback.
–
SHF MP3 WMA (or SHF CD ) appears on the display window.
Press and hold SHF for about 2 seconds during playback.
– SHF appears on the display window. MP3 WMA
2 Press SHF again.
– SHF or
SHF disappear from the display window and the random playback is can
celled.
Note
During random playback, if you press I (?m m on remote control), you won’t go back to
the previous track.
CD TEXT / ID3 TAG
CD
MP3
WMA
When playing a disc containing information, you can see the CD TEXT/ID3 TAG information.
In CD TEXT, information about the disc (disc title, performer and track title) is recorded.
In a ID3 TAG, information about the file (album title, Performer name, song title) is recorded.
In a WMA Content, information about the file (song title, Performer name) is recorded.
If there is no information, “NO TEXT” will be shown in the display window.
Press DISP repeatedly during MP3/WMA/CD TEXT file playback.
To go to a particular quickly (+10/-10 buttons)
MP3
WMA
(If there is no folder or one folder.)
U on remote control) to skip to the next 10 track, and press u/PS (u
u on remote
Press U/AS (U
control) to skip to the previous 10 track.
To skip to the next or previous folder
MP3
WMA
(If there are more than two folders.)
U on remote control) to skip to the next folder, and press u/PS (u
u on remote
Press U/AS (U
control) to skip to the previous folder.
Note
Time display appearing on the display part when playing VBR file may vary and there may be
some difference from actual time (both progress time and VBR are displayed at the same
time when playing file).
23
AUX operation
Playing an Auxiliary Equipment
You can connect Auxiliary Equipment to this unit.
Connect one to the external device jack using the line input cable (not supplied), and the
other to the AUX input jack on the control panel.
Auxiliary input
Line input cable
MP3 Player, etc
1
2
3
Press SOURCE to select the AUX as source.
AUX IN appears in the display.
Turn on the connected Auxiliary Equipment and start playing the source.
Adjust the volume.
Note
• Before operating the Auxiliary Equipment using the following procedure, select the external
input correctly. (Refer to the page 13 for details.)
• If the input level of the Auxiliary Equipment connected to the AUX input jack is not high
enough, adjust the input level properly. (Refer to the page 13 for details.)
24
Troubleshooting
Symptom
Cause
Leads and connectors are not
properly connected.
The fuse is blown.
Noise and other factors are
causing the built-in
microprocessor to operate
incorrectly.
Playback is not
possible.
The disc is dirty.
The loaded disc is of a type this
unit cannot play.
Clean disc.
Check what type the disc.
No sound is
heard.
The volume
level will not
rise.
Cables are not connected
correctly.
Connect the cables correctly.
There’s no
sound.
The volume level is low.
Adjust the volume.
There’s audio
skipping.
This unit is not firmly secured.
Secure this unit firmly.
The unit does
not operate
correctly even
when the
appropriate
remote control
buttons are
pressed.
Battery power is low.
Load new battery.
Power doesn’t
turn on.
The unit doesn’t
operate.
Correction
25
Confirm once more that all
connections are correct.
Rectify the problem that caused
the fuse to blow, and then replace
it. Be very sure to install the
correct fuse with the same rate.
Turn the unit off and then on.
Specifications
MP3/WMA Disc compatibility with this unit is limited as follows:
1.
2.
3.
4.
Sampling Frequency / 8 - 48kHz (MP3) 22.05 - 48kHz (WMA)
Bit rate / within 8 - 320kbps (include VBR) (MP3) 32 -320kbps (WMA)
CD-R/CD-RW file system should be “ISO 9660”
If you record MP3/WMA files using software which cannot create a FILE SYSTEM, for example
“Direct-CD” etc., it will not be possible to playback MP3/WMA files. We recommend that you use
“Easy-CD Creator” which creates an ISO9660 file system.
Customers should also note that permission is required in order to download MP3/WMA files and
music from the Internet.
Our company has no right to grant such permission.
Permission should always be sought from the copyright owner.
GENERAL
Output Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50W x 4CH (Max.)
Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DC 12V
Speaker impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Ω
Ground System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Negative
Dimensions (W x H x D) . . . . . . . . . . . . . . . . . . . . . . .180 x 51 x 171 mm (Without Control Panel)
Net Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.0 kg
CD SECTION
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Hz-20 kHz
S/N Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 dB
Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.05%
Channel Separation (1kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 dB
RADIO SECTION
FM
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87.5-107.9 or 87.5-108 MHz
S/N Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 dB
Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.7%
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 dBµV
AM (MW)
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .520-1720 or 522-1620 kHz
S/N Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 dB
Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.0%
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 dBµV
AUX SECTION
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Hz-20 kHz
S/N Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 dB
Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.05 %
Channel Separation (1kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 dB
Max Input Level (1kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.2 V (35 KΩ)
BLUETOOTH SECTION
TX POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 dBm
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2400-2483.5 MHz
Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bluetooth 2.0 certified
26
Bluetooth phone compatibility list
Bluetooth list and manufacturing company applicable
NR : Not Recommended
NC : Not Compatible
Company List
Company List
Company List
Nokia
Motorola
SonyEricsson
3230
3250
3650
5300
5500
6021
6103
6131
6230
6230i
6233
6270
6280
6600
6630
6650
6670
6680
6681
6820a
7370
7600
7610
8800
8910i
9500
E50
E61
E62
E70
N71
N73
N80
N90
N93
N-Gage
N-Gage QD
Samsung
LG
6060
A1000
A760 (NR)
A780i (NR)
E1000
E1070 (NR)
E680 (NR)
E680i (NR)
KRZR K1 (NR)
L6
L7
RAZA V3i
ROKR E2 (NR)
U6
V360
V3ROHS (NR)
V3X (NR)
V500
V525
V600i
SGH-D500
SGH-D600
SGH-D820
SGH-D900
SGH-E788
SGH-E900
SGH-X820
SGH-Z540V
KG245
KG800
M4410 (NR)
U890
27
Siemens
Panasonic
Sazem
Pantech
NEC
Blackberry
SHARP
K750i (NR)
K800i (NR)
P990i (NR)
S700i
T610
T628
V600i
V800
W550i
W710i (NR)
W810i
W850i (NR)
Z600
Z608
EF81
S65
SK65
SL75
SX1
SXG75
X800
myX6-2
PG8000 (NR)
PG6200
N850
N930
N730 (NR)
7130v (NC)
8070v
GX15
P/NO : MFL36538203
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising