LG | TCC-6510 | Owner's Manual | LG TCC-6510 Owner's manual

LG TCC-6510 Owner's manual
Connections
Installations
Precautions:
Be careful not to touch the
rear side panel of the unit
when
the unit
removing
from the installation sleeve,
since it may be hot. On this
side the
ribs
cooling
are
located.
Detachable Front
The unit is
designed to
operate only on 12 volt DC
negative ground electrical
Panel Car Receiver
system.
OWNER'S MANUAL
MODEL:TCC-6510
When you replace the fuse,
besuretouseafuseof
amperage for
each wire as mentioned in
chapter Connections
specified
.
Using
fuse of
a
higher
amperage may cause
serious damage to the unit.
Take time to read this OWNER S MANUAL
thoroughly. Familiarity with installation and
operating procedures will help you obtain the
best performance from your CAR Receiver.
Power
Notes:
(Red)
Use only the parts included
with the unit to ensure
proper installation. The use
of unauthorized arts can
cause malfunctions.
use
the front
A
panel
way of gripping the unit
during installation and
wiring. The front panel may
come away and the unit
may drop on the floor.
the
the unit
Connections
alcohol.
proceed
as
Bend the claws
to the
thickness
of the dashboard.
the
1
Sound
4
3
Power(PWR)
5
PWR
TN
BAND
6789
AS/PS
MD/LD
TN
12
VOL.
14
12 11
13
MUT
CLK
3
456
Connection(Black)
panel
Connect the ground lead
(black) to a metal part of the
vehicle and secure it using
the screw provided on the
vehicle for this purpose.
If this connection is loose,
on.
Press PWR button
to
(PWR)Button
EJECT()
turn it off.
other than a
metal part of the car, noise
or malfunction may result.
something
Note:
CLOCK(CLK)
Button
CASSETTE Door
LCD
Press the MD/LD button for
Turn the power ON.
than 2 seconds, activates
the loudness circuit which
Insert
currently
at the volume level memorized.
muted
operated
RELEASE Button
Press the to
cassette
a
CONTROL UP/DOWN
AS/PS Button
Button
tape
MUTE Button
BAND
AS/PS
mode mute
TN
CLK
MUTE
Radio
Basic
Operation
once
this buttons within 5
band.
seconds. After you finish
selecting modes, the unit
Select the desired stations.
Press the
TN
MD/LD
CLOCK(CLK)
TN
button 2 seconds, and clock
indication will be displayed
for 5 seconds.
Adjust
VOL.
Operating display
the
MINUTE
clock within 5 seconds.
Pressing TUNE (TN +)
button adjusts the hour.
Pressing TUNE (TN -)
adjusts the minute.
button
returns to the initial mode.
HOUR
modes:
A numeric
converted
Press the
CLOCK(CLK)
in all
previous display
5 seconds.
after
AUTO Tuning
Press the TUNE
this
buttons.
(TN +/-)
buttons for
than 1
MANUAL
more
Tuning
Press the TUNE
buttons
Loudness Function
2
BAND
345
CLOCK
6
AS/PS
MUTE
RELEASE
Button
When
TN
MD/LD
(TN +/-)
repeatedly until the
desired station appears.
the front
do not put pressure
the display or control
BAND
AS/
PS
CLOCK
6
on
MUTE
The control buttons may
not work properly if the
front
panel is not attached
properly. If this occurs,
gently press the front panel.
5
6
CLOCK
ASPS
MUTE
exposed
or
panel
high
to
direct
sunlight.
Do not
drop
the front
otherwise
subject
strong impact.
or
panel.
panel
it to
Do not allow such volatile
agents
as
benzine, thinner,
Place the Front Panel in the
or
supplied protective
contact with the surface of
case.
insecticides to
the front
Protective Case
come
into
panel.
Never try to disassemble
the front panel.
Front Panel
Operation
Memorizing Stations
24 stations
Press
can
be
Specifications
General
The selected band is
[18FM, 6AM(MW)]
quickly
the TUNE
automatically
scanned and
the 6 strongest stations
stored. Then the preset
stations
are
are
displayed
repeatedly.
Press the AS/PS button to
stop scanning the preset
stations.
(TN +/-)
Preset
more
the
Store
of the
one
PRESET(1-6)
than 2 seconds. The
station has
stored at
now
one
of the preset
buttons.
for
5
PRESET buttons.
Adjust the Volume and Tone
using MD/LD and CONTROL
Auto Store
(AS)
6 stations in the selected band
can
be stored
station for each
(1-6)
one
buttons.
When the AS/PS button is
the preset stations
monitored in sequence
pressed,
been
and
Repeat steps
remaining
a
Scanning (PS)
of PRESET
button for
each of the
Note:
BAND
4
buttons.
UP/DOWN button.
area
temperatures
23
reverses
the cassette tape.
TN
Take care not to put pressure
on the display or control
buttons, or drop the front
using
remove
in any
TN
1
be preset using PRESET
(1-6) buttons. Stations often
playback, press
() button and
are
for 5 seconds each, The
station number is shown in
the preset station indicator.
When the desired station is
received, press the AS/PS
again to stop
Power ..........................................................50 W 4(Max.)
Power Source...............................................................DC 12-15 V
Output
Speaker impedance .............................................4 x 4 or 8 x 4
Ground System .................................................................Negative
Dimensions(W H D) ..188 x 58 x 166 mm(Without Front Panel)
Net Weight ............................................................................1.3 kg
Tape Player
Tape Drive System .............................................Full Auto Reverse
Tape Speed ................................................................4.75 cm/sec.
Wow/Flutter ..............................................................0.2% (WRMS)
S/N Ratio ...............................................................................50 dB
Frequency Response ................................................40-14,000
Hz
Tuner
FM
Frequency Range
..............................65.0-74.0 MHz, 87.5-108 MHz
S/N Ratio ..................................................................................60 dB
Distortion (T.H.D. 0.5W).............................................................0.5%
Channel Separation ..................................................................30 dB
AM(MW)
kHz
button
Frequency Range .......................................................522-1,620
scanning.
S/N Ratio ..................................................................................50 dB
Distortion (T.H.D. 0.5W).............................................................0.5%
automatically.
Turn the power ON.
When the power is on, if a
cassette tape is inserted in the
playback
replacing
panel,
TN
VOL
can
To stop
EJECT
cassette
seconds.
display is
by pressing
button, the display returns
to the
frequency
MUTE
1
Note:
Operation
select the desired
PWR
impedance
following
diagram.
Refer to the
(Optional)
The tape direction
exposed
AS/PS
TN
VOL
12345
Select the desired band
using the BAND button.
automatically
desired function
CLK
Use 4~8Ohm
Signal
recalled.
when the tape end has
been reached.
CLOCK
Do not leave the front
buttons
pressed again.
BAND
TN
MD/LD
Line Out Jack
state is when any button is
Press
the time.
123456
PWR
VOL
listened to
56
4
VOL.
Press the BAND button to
by pressing
TN
Antenna Jack
TN
Turn the power ON.
CLOCK(CLK) button
momentarily to display
TN
connection
Tune in the desired station
MD/LD button, control the
the Clock Time
MDLD
4-Speakers
Hold the right part of the
front panel and pull it
towards you gently.
PWR
After you have selected the
proper mode by using the
Setting
both()
together.
the control
CONTROL UP/DOWN
Button
PWR
VOL
buttons.
The tape direction can be
reversed by pressing
with
of volume, bass, treble, balance
and fader.
MD/LD Button
BAND Button
change
your stereo unit.
speakers.
Radio
MD/LD Button
(TN +/-) Button
(CLOCK Adjust)
Press the RELEASE button
()to release the
detachable front panel.
and
Front Panel
Your will find a separate lead,
blue with a male terminal
suitable to many automatic
antenna. This lead is not to be
used with non-automatic
antenna. If an automatic car
antenna is used, when
connecting the lead, the
antenna will be automatically
extened when the main switch
is turned on. This can also be
used as a remote turn-on wire
connection for amplifiers that
have a remote sensing lead.
Using this connection will
allow simultaneous turning
on/off of the radio and an
external amplifier.
TUNE
REW/FF()
Button [DIRECTION]
Panel
two conductor
speaker
Push the front panel against
the main unit to reattach it.
the Front
Notes:
Antenna
Lead/External
Amplifier Remote
side
Display
use
Detaching
the
Panel
PWR
as
state on/off.
relesing
Always
wire between each
connections
MD/LD
The
radio.
speaker to
the Front
Attaching
Power Antenna
exposed tape side to
the right. If radio broadcast
is being received, cassette
playback automatically
begins.
boosts to compensate the
human ear's lack of sensitivity
This button is
as
from the
Connect to the Line-in RCA
jacks of the power amplifier.
the
Mute Button
before
operation.
Tape Playback
to bass at low levels.
you turn off. Whenever you
turn on the unit, it will operate
PRESET Button
Button
again
or
if the cord is connected to
more
Press PWR button or any
other button to turn the unit
volume level
POWER
Button
of the unit.
Ground
Adjustment
When you turn off, the unit is
memorized automatically the
10
rear
follows.
P/N:3828R-F018C
Location of Controls
the electrical return
path
The front panel of this unit can
be detached to prevent theft.
PWR
toward you. Do the same
operation on the other side
and pull out the unit from
the installation sleeve.
BZ03
chassis
securely
Turn-on Lead
Insert the plug of the car
antenna cable into the jack at
Insert the lever A into
hole on one side of the
unit, and pull the lever
according
Secure the connectors
so that they are
locked into position.
Improper connection can
result in noise or hamper
to utilize the vehicle's
Jacks(Optional)
Antenna Connection
Remove the rear supporter
from the unit.
Remove the front
from the unit.
near
parts whose temperature
will rise when the vehicle is
driven.
Lead
Line Out
Main connector
If you need to remove the unit
from the installation sleeve,
Installation
sleeve
Do not bring the
connecting cords
receiver is not
car
desingned
MDLD
contacts on the back of the
front panel with a cotton
swap moistened with
When removing the
unit from the
installation sleeve
Dashboard
This
Precautions
Connect the yellow memory
power supply wire to a 12V +
terminal that is always supplied
with power regardless of the
vehicle s ignition switch
position. If this connection is
made incorrectly or is not made
at all, the unit will not work.
Connect the main connector to
the female connector on the back
of the unit.
Mounting
2
Memory Back-up
(Yellow)
as a
Periodically wipe
Lead
Connect the red power supply
wire to the 12V + terminal
controlled by the car ignition
switch.
A
Consult with your nearest
car audio dealer if
installation requires the
drilling of holes or other
modifications of the vehicle.
Do not
Supply
Detachable Front Panel
compartment, tape
starts
automatically.
Select the desired band of
stations to be received.
Press the AS/PS button for
more
Note
:
The design and specifications
notice in the course of product
subject to change without
improvement.
are
than 2 seconds, and
then this function
implements.
"The
working life of
purchase."
date of
this
product
is 7 years since the
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising