LG | L2104-DP | LG L2104-DP Owner’s Manual

L2104-DN / L2104-DP
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to alert
the user to the presence of uninsulated dangerous voltage within the product’s enclosure that
may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
Regulatory Notices For U.S.A
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
• A suitable conduit entries, knock-outs or glands shall be
provided in the cable entries of this product in the end
user.
• Caution: Danger of explosion if battery is incorrectly re
placed. Replaced only with the same or equivalent type
recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
• Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall be
provided with brushings.
Warning: Do not install this equipment in a confined space
such as a bookcase or similar unit.
Caution: This installation should be made by a qualified
service person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Caution: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
Warning: Wiring methods shall be in accordance with the
National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic
environment this product may cause radio interference in
which case the user may be required to take adequate measures.
Warning: To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it means the
product is covered by the European Directive
2002/96/EC.
2. All electrical and electronic products
should be disposed of separately from the
municipal waste stream via designated
collection facilities appointed by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and
human health.
4. For more detailed information about
disposal of your old appliance, please contact your city office, waste disposal service or
the shop where you purchased the product.
LG Electronics hereby declares that this/
these product(s) is/are in compliance with
the essential
requirements and other relevant provisions
of Directive 2004/108/EC, 2006/95/EC, and
2009/125/EC.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : +31-(0)36-547-8888)
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accord
ance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally,
or has been dropped.
Cautions for Safe Operation
Power Supply
•
This camera must always be operated at DC 12V
Certified/Listed, class 2 power supply only.
Avoid the use of volatile solvents such as thinners,
alcohol, benzene and insecticides. They may damage the
surface nish and/or impair the oper ation of the camera.
Operating and storage location
Handling of the unit
Be careful not to spill water or other liquids on the unit. Be
cautions not to get combustible or metallic material inside
the body. If used with foreign matter inside, the camera is
liable to fail or to get cause of fire or electric shock.
•
Remove dust or dirt on the surface of the lens with a
blower.
•
Use a dry soft cloth to clean the body. If it is very dirty,
use a cloth dampened with a small quantity of neutral
detergent then wipe dry.
6
Avoid viewing a very bright object (such as light ttings) dur ing an extended period. Avoid operating or storing the unit in
the following locations.
•
•
•
•
•
Extremely hot or cold places (operating temperature
-10 °C to 50 °C, however, we recommend that the unit be
used within a temperature range of 0 °C to 45 °C)
Damp or dust place
Places exposed to rain
Places subject to strong vibration
Close to generators of powerful electromagnetic radia
tion such as radio or TV transmitters.
Contents
Features .......................................................................................... 8
Part Names and Functions ................................................ 9
Connections ................................................................................ 10
Installation ................................................................................... 11
Installing the camera on a ceiling or wall ......................... 11
Adjustment .................................................................................... 13
Lens Focus Adjustment .......................................................... 14
Menu Operation .........................................................................
OSD Menu Overview ..............................................................
General Operation ..................................................................
Exposure Settings ..................................................................
15
16
18
19
BLC/LSC setting ...................................................................... 19
Day/Night Setting ...............................................................
Motion Detection Setting .................................................
Privacy Setting .......................................................................
Special Menu Settings ......................................................
Setting the SHARPNESS .............................................
Setting the MONITOR .................................................
Setting the GAMMA effect ..........................................
Setting MIRROR effect .................................................
Setting USER TITLE ........................................................
DPC Setting ..................................................................
LANGUAGE Setting ......................................................
22
23
25
26
26
26
26
26
27
28
28
Reset Setting ................................................................................. 29
Speci-fication ............................................................................... 30
BRIGHTNESS setting ............................................................... 20
AGC (Automatic Gain Control) setting ................................ 20
SHUTTER (Shutter Speed) setting ......................................
.....
20
White Balance settings ................................................................. 21
7
Featur es
This Color Video Camera is designed for installation in an
indoor video surveillance system.
This manual contains instructions on how to install and manage the Color Video Camera in your video surveillance system.
Should you require any technical assistance, please contact
authorized service center.
• 1/3" SUPER HAD COLOR CCD II
• Resolution: 540TV Lines
Accessories
DOME CAMERA
VIDE O OUTPUT
TE S T C ABLE
• DAY/NIGHT Automatically change
• 3.6mm Fixed Focus lens (F2.0)
• Min. illumination 0.05 Lux
SCREW
• Use of DC 12V
• 3 Axis Adjustable
• OSD Adjustment
• Easy, Simple & Convenient installation
INSTALL ATION
MANUAL
TEMPLATE
8
Part Names and Functions
12. Lens Protection Tape
9
Monitor(or
10
)
Installation
Installing the camer a on a ceiling or wall
1. To install it, please take off the lens protection tape after opening the dome cover.
2. Secure the camera mounting bracket to the position where the camera should be mounted with the supplied screws.
(Please leave a good position of cable not to interrupt the surveillance area with it when installing.)
Lens Protection Tape
Tapping Type(Supplied)
3.5x20mmx3ea
11
Installation
③ . Adjust the camera lens to face the area to be monitored and
x the
main body and the dome cover by aligning the grooves and rotating
the body clockwise.
12
Installation
Adjustment
Service Video connector
Connect a portable monitor to the video jack.
Having a better view , adjust the camera
Rotate angle : 360˚
Panning angle : 360˚
Tilting angle : 90˚
PAN 360˚
R OTATE 360˚
TIL T 90˚
13
Lens Focus Adjustment
• The lens is focused far from 1M when ex-factory.
Therefore we recommend the lens focus as is.
14
Menu Operation
This camera utilizes an on-screen user MENU.
To set items on the menu, use the following switch.
UP
Used to move upper direction on the menu screen. Use
this button to select an item or adjust the parameters.
DOWN
Used to move lower direction on the menu screen. Use this
button to select an item or adjust the parameters.
RIGHT
:SET
Moves the cursor to the right. Used to increment the value
selected in the menu. The parameter changes each time
this button is pressed.
LEFT
Moves the cursor to the left. Used to decrement the value
selected in the menu. The parameter changes each time
this button is pressed.
SET
Executes selections and displays a submenu for an item
with the
. mark.
15
Menu Operation
OSD Menu Overview
Main Menu
The following table shows the list of menu items and options.
You can adapt the camera to your requirements by setting up the
respective items in these menus.
Main Menu
Sub Menu
Contents
BLC / LSC
BRIGHTNESS
EXPOSURE
ELC
AGC
SHUTTER
16
EXPOSURE
HSBLC
LSC
BLC
WIDE BLC
0~99
OFF
LOW
MIDDLE
HIGH
AUTO
1/120FLK
1/250
Sub Menu
ELC
Contents
SHUTTER
1/500
1/1000
1/2000
1/4000
1/10000
1/100000
ATW
AWB
R-Y GAIN
B-Y GAIN
0~255
0~255
MANUAL
MANUAL R
MANUAL B
0~255
0~255
BURST
DAY > NIGHT
NIGHT > DAY
DELAYTIME
ON/OFF
0~255
0~255
3~12
WHITE BAL
PUSH
DAY&NIGHT
AUTOAUTO
Menu O peration
Main M enu
DAY&NIGHT
Sub M enu
COLOR
B&W
OFF
Contents
ON
Sub M enu
OFF
MONITOR
SET WINDOW
ALL SET
ALL CLEAR
SENSITIVITY
TRACE
HOLD TIME
ON/OFF
GAMMA
0~200
OFF
ICON
TRACE
1~15
SPECIAL
ON
MASK NUMBER
DISPLAY
COLOR
ON
HEIGHT
WIDTH
MOVE Y
MOVE X
1~4
ON/OFF
GRAY
BLACK
WHITE
1~99
1~99
1~99
1~99
MIRROR
USER TITLE
DPC SET
OFF
PRIVACY
Contents
SHARPNESS
ALARM
MOTION DET
Main M enu
LANGUAGE
RESET
1~49
CRT
LCD
USER
0.45
0.6
1
ON
OFF
ON
OFF
WHITE THR
LUMA LIMIT
ENG
한국어
FACTORY
17
Menu Operation
OSD MENU
OSD(SCREEN CONTROL)-SETTING
CAMERA SETTING
EXPOSURE
WHITE BAL
DAY & NIGHT
MOTION DET
PRIVACY
SPECIAL
RESET
EXIT
ELC
ATW
AUTO
OFF
OFF
1.Press OSD key down at inside of Dome base.
The setup menu screen appears on the monitor.
2.Press OSD key to upside or downside to select an option then
Press OSD key down. Submenu appears on the monitor.
3.Press OSD key to upside or downside to select a Submenu option.
4.Use OSD key to left or right to select a value.
5.Select [EXIT] and click the OSD key. Then OSD is setup.
RET: Return to the previous menu .
TOP: Return to the CAMERA SETTING menu screen.
END: Exit the setup menu.
18
Menu Operation
OSD MENU-Exposure Settings
OSD MENU-Exposure Settings(BLC / LSC)
You can set the exposure options using the EXPOSURE menu.
Use WIDE BLC option to view the object clearly in strong
CAMERA SETTING
EXPOSURE
WHITE BAL
DAY & NIGHT
MOTION DET
PRIVACY
SPECIAL
RESET
EXIT
ELC
ATW
AUTO
OFF
OFF
backlight conditions.
EXPOSURE-ELC
BLC/LSC
BRIGHTNESS
AGC
SHUTTER
EXIT
BLC
45
MIDDLE
AUTO
RET
1.Select [WIDE BLC]] option.
2.Use OSD key to left or right to select a mode then press[SET].
Select[EXPOSURE]option on the[CAMERA SETTING]menu.
[BLC]-After click [BLC], you can move OSD key left/right
Press OSD key down and the EXPOSURE menu appears.
[BLC]-[ON]or[OFF], it's level.
To see [ELC]] and press down to click it.
Then press down [RET] for BLC setting.
this function is for clear image even if backlight condition.
-WIDE BLC : Use for adjusting brightness of the subject and
Select [BLC], [WIDE BLC], [LSC]or[ HSBLC]
background image to view the both of object clearly at the
same time in backlight condition.
-INDOOR: WIDE BLC ON
-OFF
19
Menu Operation
BLC : Use for adjusting brightness of the subject to view the
object clearly in backlight condition. Set to select [on] or [off]
HSBLC : Use for masking brightness of the specific area to
view the subject more clearly.
The HSBLC mode is automatically activated only in low
illumination scene.
Push OSD key to left or right to select a ON or OFF.
Press[SET] to exit the Area setting menu.
-ON: It has powerful back light compensation performance.
OSD MENU-Exposure Settings
CAMERA SETTING
EXPOSURE
WHITE BAL
DAY & NIGHT
MOTION DET
PRIVACY
SPECIAL
RESET
EXIT
ELC
ATW
AUTO
OFF
OFF
1.Select [BRIGHTNESS]
/ [AGC] / [SHUTTER]
option.
2.Use OSD key to left
or right to select a mode
then press[SET].
The function suppress highlight then it will make the objects
very clean and obvious.
-OFF: Not used.
LSC: It can compensate the shading correction curve on
each corners of the views.
EXPOSURE-ELC
BLC/LSC
BRIGHTNESS
AGC
SHUTTER
EXIT
BLC
45
MIDDLE
AUTO
RET
BRIGHTNESS : You can set the brightness level. (0-100)
AGC : If the images are too dark, change the maximum [AGC]
value to make the images lighter.
SHUTTER : (AUTO→1/120FLK→1/250
20
1/100000)
Menu Operation
OSD MENU-White Balance settings
You can select one of three modes for white balance adjustment.
CAMERA SETTING
EXPOSURE
WHITE BAL
DAY & NIGHT
MOTION DET
PRIVACY
SPECIAL
RESET
EXIT
ELC
AWB
AUTO
OFF
OFF
WHITE BAL-MANUAL
R-Y GAIN
B-Y GAIN
EXIT
128
128
END
WHITE BAL-MANUAL
MANUAL R
MANUAR B
EXIT
1.Select [WHITE BAL] option.
2.Use OSD key to left or right
to select a mode thenpress
[SET].[ATW]↔[AWB]↔
[MANUAL]↔[PUSH]
75
160
RET
AWB(Auto-Tracing White Balance) : The color temperature
AWB(Auto White Balance)-AWB detects while color balance
range for the proper white balance is approximately
on the screen and based on sensor white balance functions
2500 - 9500˚K.
automatically between the range of 0 255.
Proper white balance may not be obtained under the following
MANUAL: You can set the white balance options manually.
conditions : The color temperature is out of the
-MANUAL R: Obtains the optimum amount of red gain.(0 255)
2500 - 9500˚K range.
-MANUAL B: Obtains the optimum amount of blue gain.(0 255)
When the scene contains mostly high color temperature
PUSH: Temporary automatic tracing white Balance.
objects, such as a blue sky or sunset.
21
Menu Operation
OSD MENU-Day/Night Setting
CAMERA SETTING
EXPOSURE
WHITE BAL
DAY & NIGHT
MOTION DET
PRIVACY
SPECIAL
RESET
EXIT
ELC
ATW
AUTO
OFF
OFF
DAY & NIGHT-AUTO
BURST
DAY>NIGHT
NIGHT>DAY
DELAY TIME
EXIT
ON
120
90
5
RET
1.Select [DAY/NIGHT]option.
2.Use OSD key to left or right to select mode for
day/night function.
-AUTO : You will be able to change the Day/Night
mode automatically.
Select [Burst on] or [Burst off] as you want
DAY>NIGHT : Set the start brightness control from the location
DELAY TIME : This function allows you to set delay time of
-0(High Light)
when to change camera to Day & night mode (3 12 sec)
255(Low Light)
NIGHT>DAY : Set the end brightness control from the location
-COLOR : Color mode enabled.
-0(High Light)
-B/W : Black-and-white mode enabled.
22
255(Low Light)
Menu Operation
OSD MENU-MOTION DETECTION Setting
[MOTION DET] detects the moving objects in the scene by
monitoring changes in brightness level.
Select the level of sensitivity for motion detection to 4 zone.
CAMERA SETTING
EXPOSURE
WHITE BAL
DAY & NIGHT
MOTION DET
PRIVACY
SPECIAL
RESET
EXIT
ELC
ATW
AUTO
OFF
OFF
MOTION DET
ALARM
SET WINDOW
ALL SET
ALL CLEAR
SENSITIVITY
TRACE
HOLD TIME
EXIT
OFF
200
ICON
5
RET
1. Select[MOTION DET]option.
SET WINDOW : Use OSD key to left or right to select some
2. Use OSD key to left or right to select a [ON] and
windows and click them as you want. One more click, it set-off.
press [SET].
The [MOTION DET] menu appears and select [ALARM ON].
Note : In order to get back to previous menu, move to the edge
of left or right and push the KEY down one second or more.
Otherwise you can not control [Motion Detection] mode.
23
Menu Operation
OSD MENU-MOTION DETECTION Setting
CAMERA SETTING
EXPOSURE
WHITE BAL
DAY & NIGHT
MOTION DET
PRIVACY
SPECIAL
RESET
EXIT
ELC
ATW
AUTO
OFF
OFF
MOTION DET
ALARM
SET WINDOW
ALL SET
ALL CLEAR
SENSITIVITY
TRACE
HOLD TIME
EXIT
OFF
200
ICON
5
RET
ALL SET : it's to select all windows.
TRACE : [ICON]↔[TRACE]↔[OFF]
ALL CLEAR : it's to clear all windows.
-ICON : it appears a icon when set some areas and set [ICON].
left or right and push the KEY down one second or more.
-TRACE : no icon but set trace on
[SENSITIVITY] : Obtain the optimum detection level.(0 200)
-OFF : off Trade mode
HOLD TIME : select 1 15 sec for the trace
24
Menu Operation
OSD MENU-Privacy Setting
This function is aiming at the protection of personal privacy,
selecting a screen part black not to be displayed in the screen.
Up to 4 zones can be registered.
CAMERA SETTING
EXPOSURE
WHITE BAL
DAY & NIGHT
MOTION DET
PRIVACY
SPECIAL
RESET
EXIT
ELC
ATW
AUTO
OFF
OFF
1. Select PRIVACY [ON] and the menu appears.
2. Select [MASK NUMBER] one of 1, 2, 3, 4 This number
starts from the left top area with clockwise.
3. If you'd like the mask appears on the monitor, select
[DISPLAY] [on] to move OSD key to left or right.
PRIVACY
MASK NUMBER
DISPLAY
COLOR
HEIGHT
WIDTH
MOVE Y
MOVE X
EXIT
1
OFF
GRAY
18
22
17
27
RET
4. Select one of[GRAY]↔[WHITE]↔[BLACK]for the mask
color in [COLOR]
5. You can make the area dimension to move OSD key for the
level of [DEPTH] & [WIDTH].
6. Also you can move the position of privacy area to X axis or
Y axis as you want.
After setting all information, please exit this menu.
25
Menu Operation
OSD MENU-Special Menu Settings
This menu lets you adjust and set up SHARPNESS, GAMMA,
MIRROR, USER TITLE, DPC SET, LANGUAGE function by
yourself in the SPECIAL menu.
CAMERA SETTING
EXPOSURE
WHITE BAL
DAY & NIGHT
MOTION DET
PRIVACY
SPECIAL
RESET
EXIT
ELC
ATW
AUTO
OFF
OFF
SPECIAL
SHARPNESS
MONITOR
GAMMA
MIRROR
USER TITLE
DPC SET
LANGUAGE
EXIT
1. Select [SPECIAL] option.
2. Press OSD key down and the SPECIAL menu appears.
Setting SHARPNESS
You can select SHARPNESS level.
-Select [SHARPNESS] option on the [SPECIAL] menu.
-Use OSD key to left or right to adjust the sharpness level.
26
10
LCD
0.45
OFF
OFF
ON
ENG
RET
MONITOR : Select [LCD] or [CRT] which you use.
Then you can get a clearer image.
GAMMA : Brightness control could be functioning from
[0.45] -> [0.6] -> [1.0] -> [USER]
MIRROR : The MIRROR function is selected [ON] or [OFF] with
OSD key to left or right. The image can be Left-right reversal.
Menu Operation
OSD MENU-Special Menu Settings (Setting the USER TITLE)
SPECIAL
SHARPNESS
MONITOR
GAMMA
MIRROR
USER TITLE
DPC SET
LANGUAGE
EXIT
USER TITLE
15
LCD
0.45
OFF
OFF
ON
ENG
RET
A B C D E F G H I J
K L M N O P Q R S T
UVWXYZ : =
@
# $ % & ( ) * + - .
0 1 2 3 4 5 6 7 8 9
<< >> CLR POS END
L G_______________
You can use the camera identification to assign a number
<< >> : Space
and character to the camera (0 - 9, A-Z & special character).
CLR: Clear the letters.
The USER TITLE is displayed on the upper side of the screen.
POS: Position User Title where you want
To disappear the user title, select [OFF].
END: Return to Previous Menu
To use OSD key to left/right or up/down, click .the desired letter.
27
Menu Operation
OSD MENU-Special Menu Settings DPC SET
(DEFECT PIXEL CANCELLATION)
2 Adjust the value on WHITE THR(white defect threshold)
SPECIAL
SHARPNESS
MONITOR
GAMMA
MIRROR
USER TITLE
DPC SET
LANGUAGE
EXIT
This menu compensate these defect pixels.
1. Select [DPC SET] option on SPECIAL menu and press [ON].
15
LCD
0.45
OFF
OFF
ON
ENG
RET
3. Adjust the value of LUMA LIMIT (Luminance value limitation)
OSD MENU-LANGUAGE
This menu lets you select English or Korean.
1.Select [LANGUAGE], move OSD key to left or right.
2.Then you can select ENG(English) Now.
SPECIAL
DPC SET
WHITE THR
LUMA LIMIT
EXIT
150
20
RET
This menu lets you adjust to set the Defect Pixel Cancellation.
While using CCD, defect pixel(white pixel & black pixel) occurs.
28
SHARPNESS
MONITOR
GAMMA
MIRROR
USER TITLE
DPC SET
LANGUAGE
EXIT
15
LCD
0.45
OFF
OFF
ON
ENG
RET
Menu Operation
OSD MENU-RESET SETTING
CAMERA SETTING
EXPOSURE
WHITE BAL
DAY & NIGHT
MOTION DET
PRIVACY
SPECIAL
RESET
EXIT
ELC
ATW
AUTO
OFF
OFF
1. Select [RESET] option.
2. Press OSD key down and the reset menu appears
3. Push OSD key down for FACTORY SET.
4. And move to [EXIT] and click.
NOTE: After [EXIT] setting, [RESET] is setting.
RESET
FACTORY SET
EXIT
RET
29
Specification
Model
Signal System
Total Pixels No . /
Effective Pixels No .
Image De vic e
Lens
Sync. System
Scanning Frequency (H/V)
Horizontal Resolution
S/N Ratio
Minimum Illumination
Control Method
Video Output Signal
Day & Night
WDR(BLC)
Auto Gain Control
30
L2104-DP
PAL
L2104-DN
NTSC
470K/440K
410K/380K
1/3" CCD(ICX638/639BK)
3.6mm Fixed Lens
Internal
15.625 KHz/50Hz
15.734 KHz/60 Hz
540 TVL
48 dB ~
0.05 Lux (F1.2)
Inner OSD key button
1Vp-p Composite (75Ω)
Auto/Color/B&W
WIDE BLC/BLC/HSBLC/LSC
OFF/LOW/MIDDLE/HIGH
Specification
Electronic Shutter Speed
White Balance
Motion Detection
Privacy Zone Masking
Monitor
Mirror
DPC Set
Power Consumption
Operation Temp./Humidity
Storage Temp./Humidity
Weight
Dimension( øx H)
Accessory
AUTO, 1/120FLK, 1/250 ~ 1/100000
ATW/AWB/MANUAL/PUSH
Set Window / All Set
4 Masks
CRT/LCD
ON/OFF
ON/OFF
DC 12V/1.15W
-10 ºC ~ 50 ºC ( 0%RH ~ 80%RH )
-20 ºC ~ 60 ºC ( 0%RH ~ 85%RH )
300g
ø(90+125) X 85mm
Template, Video Output Test Cable
31
P/N :
Download PDF

advertising