OWNER'S MANUAL
Color Video Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
L5223 Series
P/NO : MFL67259825
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s enclosure
that may be of sufficient magnitude
to constitute a risk of electric shock to
persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying the product.
2
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if
an unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
t
A suitable conduit entries, knock-outs or glands shall
be provided in the cable entries of this product in the
end user.
t
t
Caution: Danger of explosion if battery is incorrectly
replaced. Replaced only with the same or equivalent
type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s
instructions.
Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall be
provided with brushings.
Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
To disconnect power from mains, pull out the mains
cord plug. When installing the product, ensure that the
plug is easily accessible.
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
Warning: Do not install this equipment in a confined space
such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the
National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Warning: To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
Caution: This installation should be made by a qualified
service person and should conform to all local codes.
3
Disposal of your old appliance
1.
When this crossed-out wheeled bin
symbol is attached to a product it means
the product is covered by the European
Directive 2002/96/EC.
2.
All electrical and electronic products
should be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or the
local authorities.
3.
The correct disposal of your old
appliance will help prevent potential
negative consequences for the
environment and human health.
4.
For more detailed information about
disposal of your old appliance,
please contact your city office, waste
disposal service or the shop where you
purchased the product.
EEE Compliance with Directive. (for Turkey only)
4
LG Electronics hereby declares that this/these
product(s) is/are in compliance with the essential requirements and other relevant provisions
of Directive 2004/108/EC, 2006/95/EC, and
2009/125/EC.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : +31-(0)36-547-8888)
Important Safety Instructions
1.
Read these instructions.
and the point where they exit from the apparatus.
2.
Keep these instructions.
3.
Heed all warnings.
11. Only use attachments/accessories specified by the
manufacturer.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
5
Cautions for Safe Operation
Power Supply
Operating and storage location
This camera must always be operated a AC 24 V or DC 12 V
Certified/Listed, class 2 power supply only.
Avoid viewing a very bright object (such as light fittings)
during an extended period. Avoid operating or storing the
unit in the following locations.
Handling of the unit
Be careful not to spill water or other liquids on the unit. Be
cautions not to get combustible or metallic material inside
the body. If used with foreign matter inside, the camera is
liable to fail or to get cause of fire or electric shock.
t
Remove dust or dirt on the surface of the lens with a
blower.
t
Use a dry soft cloth to clean the body. If it is very dirty,
use a cloth dampened with a small quantity of neutral
detergent then wipe dry.
t
Avoid the use of volatile solvents such as thinners,
alcohol, benzene and insecticides.
They may damage the surface finish and/or impair the
operation of the camera.
6
t
Extremely hot or cold places (operating temperature
-10 °C to 50 °C, however, we recommend that the unit
be used within a temperature range of 0 °C to 45 °C)
t
Damp or dust place
t
Places exposed to rain
t
Places subject to strong vibration
t
Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
Contents
Features ............................................................................. 8
White Balance settings .........................................................25
Accessories.................................................................................. 8
3D-DNR Setting .......................................................................26
Part Names and Functions ............................................... 9
Day/Night Setting ..................................................................27
Connections .................................................................... 11
Privacy Setting .........................................................................28
Basic connection .....................................................................11
Special Menu Settings ..........................................................29
Installation ...................................................................... 12
LANGUAGE Setting.......................................................29
Setting the COLOR........................................................30
Setting the SHARPNESS effect .................................30
STABILIZER setting........................................................31
Setting the D-ZOOM (Digital Zoom ) level .........31
Setting the D-EFFECT (Digital effect) ....................32
Motion Detection Setting .........................................32
Reset Settings ................................................................33
Specification ................................................................... 34
Mounting the camera ...........................................................12
Image Adjustment .................................................................15
Menu Operation.............................................................. 18
OSD Menu Overview .............................................................19
General Operation..................................................................21
Setting the USER TITLE..........................................................21
Exposure Settings ...................................................................22
WDR/BLC setting ...........................................................22
BRIGHTNESS setting.....................................................23
AGC (Automatic Gain Control) setting ..................24
SHUTTER (Shutter Speed) setting ...........................24
SENS-UP setting ............................................................25
7
Features
This Color Video Camera is designed for installation in an
indoor video surveillance system.
This manual contains instructions on how to install and
manage the Color Video Camera in your video surveillance
system.
Should you require any technical assistance, please contact
authorized service center.
t
High resolution and high sensitivity with a 6 mm CCD.
t
Day & Night function.
t
WDR/BLC covers various light conditions
t
Excellent signal-to-noise ratio of 52 dB
t
Power Supply : Automatically switch between
DC 12 V and AC 24 V
Accessories
Installation sticker
Camera mounting
bracket
M3 Fixing screws
8
Part Names and Functions
a Dome Cover
b Focus lock lever
Fixes the focus position after adjusting.
c Azimuth adjuster
a
Adjusts the azimuth angle to obtain a level image.
d Zoom lock lever
Fixes the zoom position after adjusting.
b
c
d
e
e Tilting lock screw
Fixes the tilting position after adjusting.
f Video Out connector
Use this jack for checking the picture with portable
monitor when install the camera.
g Setup menu control buttons
f
g
9
Part Names and Functions
h Power input connector
Supplies AC 24 V or DC 12 V from an external power
source.
i Video output connector (BNC type)
j Pan adjuster
Adjusts the pan position.
k Camera mounting bracket
h
i
j
k
10
This bracket is supplied for ceiling installation.
Connections
Basic connection
2.
Connect a external power source to the power input
jack of the camera.
The peripheral devices (DVR, monitor, etc.), AC/DC adapter
and cables are not supplied.
1.
Connecting the monitor.
Make the video signal connection between the camera and the monitor or DVR.
11
Installation
Mounting the camera
Follow the instructions below to surface mount the camera.
1.
12
Use the installation guide template to check the
mounting location. Face the front of the label toward
the area of interest. Using the template as a guide,
make a hole through the ceiling.
2.
Pass the connection cable through the inner side of
the ceiling.
Installation
3.
Install the camera mounting bracket to the ceiling.
4.
Connect the cables to the cable jacks of the camera
body.
13
Installation
5.
Assemble the camera and mounting bracket. Connect
the unit by following step a and b.
6.
14
Turn the dome cover to adjust the camera view point .
Installation
Image Adjustment
2.
Connect a portable monitor to the video jack.
You can manually adjust the pan/tilt/azimuth angles, focus,
and zoom while observing the connected monitor.
Notes:
t
Do not hold the camera by lens unit to adjust panning,
tilting, or azimuth.
t
The video output to the BNC will be interrupted while
a portable monitor is connected to the video jack.
1.
Remove the Dome cover.
15
Installation
3.
Adjust the pan/tilt position of the camera.
3-1. Loosen the pan/tilt lock screw.
3-2. Lock the pan/tilt lock screw after adjusting.
16
4.
Adjust the azimuth angle.
Installation
5.
Adjust the zoom.
6.
Adjust the focus
5-1. Unlock the zoom lever.
6-1. Unlock the focus lever.
5-2. Move the lever to adjust the zoom.
6-2. Move the lever to adjust the focus.
5-3. Lock the lever.
6-3. Lock the lever.
NEAR
WIDE
FAR
TELE
7.
Attach the dome cover.
17
Menu Operation
This camera utilizes an on-screen user MENU. To set items
on the menu, use the following buttons.
t
UP button:
Used to move upper direction on the menu screen.
Use this button to select an item or adjust the parameters.
t
DOWN button:
Used to move lower direction on the menu screen. Use
this button to select an item or adjust the parameters.
t
RIGHT button:
Moves the cursor to the right. Used to increment the
value selected in the menu. The parameter changes
each time this button is pressed.
t
LEFT button:
Moves the cursor to the left. Used to decrement the
value selected in the menu. The parameter changes
each time this button is pressed.
t
SET button:
Executes selections and displays a submenu for an
item with the mark.
18
Menu Operation
OSD Menu Overview
The following table shows the list of menu items and options. You can adapt the camera to your requirements by
setting up the respective items in these menus.
Main Menu
USER TITLE
Sub Menu
Contents
OFF
-
ON
WDR/BLC
BRIGHTNESS
AGC
EXPOSURE
ALC /ELC /ALC2
SHUTTER
Main Menu
Sub Menu
EXPOSURE
ALC/ELC/ALC2
SENS-UP
Contents
ATW
USER MODE
OFF
AUTO
STANDARD
VIVID
WARM
COOL
WHITE BAL
OFF/WDR/BLC/
HSBLC
A.FLK,1/160, ...,
1/100 000
(for ALC2 mode)
INDOOR,
OUTDOOR
-100 to 100
COLOR TEMP
MANUAL
0 to 100
OFF/LOW/MIDDLE/
HIGH
1/100 000, ..., 1/160,
A.FLK, OFF, AUTO, x2,
..., x512
(for ALC/ELC mode)
AWC / PUSH
RED
BLUE
3D-DNR
-100 to 100
OFF
-
LOW
-
MIDDLE
-
HIGH
LOW/ MIDDLE/
HIGH
5, 10, 15, 30,
60 SEC
LEVEL
AUTO
DWELL TIME
DAY/NIGHT
DAY
-
NIGHT
-
19
Menu Operation
Main Menu
PRIVACY
Sub Menu
Contents
OFF
-
ON
Main Menu
Sub Menu
LANGUAGE
Contents
ENG/CHN/KOR/JAP/FRE/ITA/SPA/POR/
DUT/GER/POL/RUS/TUR/ARA/HEB
MASK NUMBER
AREA1 to AREA8
DISPLAY SET
ON/OFF
SHARPNESS
0 to 68
COLOR SET
GRAY/ WHITE/
BLACK
STABILIZER
OFF/ ON
HEIGHT
4 to 100
COLOR EFFECT
OFF
D-ZOOM
WIDTH
4 to 100
MOVE Y
2 to 98
MOVE X
2 to 98
OFF/ ON
SPECIAL
D-EFFECT
ON
OFF/ V-FLIP/ MIRROR/ ROTATE
OFF
MOTION DET
ON
EXIT
20
ZOOM
PAN
TILT
FACTORY RESET
-
ZONE
NUMBER
ZONE STATE
HEIGHT
AREA1 to
AREA4
OFF/ON
12 to 100
WIDTH
16 to 100
MOVE Y
MOVE X
SENSITIVITY
6 to 94
8 to 92
0 to 100
-
Menu Operation
General Operation
Setting the USER TITLE
1.
You can use the camera identification to assign a number
and character to the camera.
The USER TITLE is displayed on the upper left of the screen.
To disappear the user title, select [OFF].
Press [SET] button.
The setup menu screen appears on the monitor.
2.
Use [UP] or [DOWN] button to select an option then
press [SET] button.
Submenu appears on the monitor.
3.
Use [UP] or [DOWN] button to select a submenu
option.
4.
Use [LEFT] or [RIGHT] button to select a value.
5.
Select [EXIT] option then press [SET] to exit the setup
menu. In the submenu, use [UP] or [DOWN] button to
select the [RETURN] then press [SET] to return to the
previous setup menu.
t
1.
Select [USER TITLE] option.
2.
Use [LEFT] or [RIGHT] button to select a [ON] then
press [SET]. The USER TITLE menu appears.
A
3.
Use [UP], [DOWN], [LEFT] or [RIGHT] button to select
a character or number then press [SET] button.
t
CLR: Clear all entered characters and numbers.
t
POS: Move the USER TITLE position on the screen
using the arrow buttons.
RETURN: Return to the previous.
21
Menu Operation
t
END: Confirm your selection or exit the setting
WDR/BLC setting
t
A (Blank): Inserts a space at the cursor position.
Use WDR/BLC option to view the object clearly in backlight
conditions.
t
/
: Moves cursor to left or right.
Exposure Settings
You can set the exposure options using the EXPOSURE
menu.
1.
Select [EXPOSURE] option on the [CAMERA SETTING]
menu.
2.
Use [LEFT] or [RIGHT] button to select a mode.
1.
Select [WDR/BLC] option.
3.
Press [SET] button and the EXPOSURE menu appears.
2.
Use [LEFT] or [RIGHT] button to select a mode then
press [SET].
22
t
WDR: WDR (Wide dynamic range) feature can be
very helpful to cope with very challenging lighting conditions. It is capable of capturing both of
the dark part and bright part and combining the
differences into a scene to generate a highly realistic image as original scene. Set the WDR limit.
t
BLC: Camera's backlight compensation feature
Menu Operation
helps alleviate issues of visibility in high contrast
areas. Set the BLC limit.
t
HSBLC: Use for masking brightness of the specific
area to view the subject more clearly. The HSBLC
mode is automatically activated only in low luminance scene.
You can increase the brightness of the darkened video. If
you set the brightness to lower value, the image is darkened. If you set the brightness to higher value, the image
gets bright.
>
t
AREA SETTING: Use [LEFT] or [RIGHT] button to select a area then use [UP] or [DOWN]
button to select a [ON] or [OFF]. Press [SET]
to exit the Area setting menu.
> GRAY SCALE: Use [LEFT] or [RIGHT] button
to select a gray scale. (GRAY, D.GRAY, BLACK)
> USER SCALE: Use [LEFT] or [RIGHT] button
to select a bright level. (5 level)
> MASK: Use [LEFT] or [RIGHT] button to
select [ON] or [OFF].
If you set the MASK to ON, the mask function
is activate only when the HSBLC is automatically activated in low luminance scene.
OFF: Not used.
BRIGHTNESS setting
1.
Select [BRIGHTNESS] option.
2.
Use [LEFT] or [RIGHT] button to set the bright level.
23
Menu Operation
AGC (Automatic Gain Control) setting
SHUTTER (Shutter Speed) setting
If the images are too dark, change the maximum [AGC]
value to make the images brighter.
Select the desired shutter speed for camera exposure. You
can change the shutter speed to higher speed to capture
fast-moving subjects, though the image becomes darker.
1.
Select [AGC] option.
2.
Use [LEFT] or [RIGHT] button to select a mode.
1.
Select [SHUTTER] option.
2.
Use [LEFT] or [RIGHT] button to set shutter speed.
Note:
If you set the shutter speed value in ALC2 mode, it is maximum value. When the camera is activated with ALC2 mode,
the shutter speed is arrived maximum value and then the
camera is change to iris control mode automatically for the
camera exposure.
24
Menu Operation
SENS-UP setting
Note:
If pictures are not clear due to darkness, this SENS-UP
operation would increase the sensitivity of picture.
If you set to one of the SHUTTER options except AUTO on
the [SHUTTER] menu or [AGC] to [OFF], the [SENS-UP] setting is not available and [---] mark is displayed.
White Balance settings
Select the method by which the camera shifts its output
colors to compensate for the color of a light source.
1.
2.
Use [UP] or [DOWN] button to select [SENS-UP]
option.
Use [LEFT] or [RIGHT] button to select mode.
t
AUTO: Adjust the sensitivity of the picture automatically.
>
t
SENS-UP LIMIT: Use [LEFT] or [RIGHT] button to set the SENS-UP limit.
OFF: Not used.
1.
Select [WHITE BAL] option.
2.
Use [LEFT] or [RIGHT] button to select a mode then
press [SET].
25
Menu Operation
t
-
ATW (Auto-Tracing White Balance): Use [LEFT]
or [RIGHT] button to select the ATW then press
[SET] button.
You can select the USER MODE.
>
>
t
AWC/PUSH: If you select the AWC/PUSH
mode, you will be able to set up the White
Balance automatically using [SET] button.
t
MANUAL: You can set the white balance options
manually.
>
26
COLOR TEMP: Use [LEFT] or [RIGHT] button
to select a function.
INDOOR: The color temperature
range for the proper white balance is
approximately 3 200 K.
OUTDOOR: The color temperature
range for the proper white balance is
approximately 5 100 K.
RED: Obtains the optimum amount of red
gain.
BLUE: Obtains the optimum amount of blue
gain.
3D-DNR Setting
Menu Operation
1.
2.
Select [3D-DNR] option.
If pictures are not clear due to brightness, this option
would reduce the noise of picture.
Use [LEFT] or [RIGHT] button to select a option.
1.
Select [DAY/NIGHT] option.
2.
Use [LEFT] or [RIGHT] button to select mode
for Day/Night function.
t
Notes:
AUTO: You will be able to change the Day/Night
mode automatically.
t
Note:
t
If you set the AGC to [OFF] on the [EXPOSURE] menu,
the [3D-DNR] function is not available and [---] mark
is displayed.
If you set the AGC to [OFF] or the SHUTTER is set
to one of the SHUTTER options except AUTO on
the [EXPOSURE] menu, the AUTO mode of the
DAY/NIGHT function is not available and [---]
mark is displayed.
When you use this function, the afterimage may occur.
>
t
LEVEL: Use [LEFT] or [RIGHT] button to
select a level.
> DWELL TIME: Use [LEFT] or [RIGHT] button
to select a dwell time.
DAY: Color mode enabled.
t
NIGHT: Black-and-white mode enabled.
Day/Night Setting
27
Menu Operation
Privacy Setting
5.
Use [LEFT] or [RIGHT] button to set up the GRAY,
WHITE or BLACK on the COLOR SET option.
This function is aiming at the protection of personal privacy, selecting a screen part black not to be displayed in
the screen. Up to 8 zones can be registered.
6.
Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
t
HEIGHT: Enlarge or decrease the vertical size of
the mask.
t
WIDTH: Enlarge or decrease the horizontal size of
the mask.
t
MOVE Y: Moves vertical position of the mask.
t
MOVE X: Moves horizontal position of the mask.
Note:
1.
Select [PRIVACY] option.
2.
Use [LEFT] or [RIGHT] button to select a [ON] and
press [SET]. The PRIVACY SETUP menu appears.
3.
Use [LEFT] or [RIGHT] button to select a mask (AREA1
to AREA8) on the [MASK NUMBER].
4.
Use [LEFT] or [RIGHT] button to set up the ON or OFF
on the DISPLAY SET option.
28
The parts with the registered mask numbers from AREA1 to
AREA4 have the same color. (So do the parts with the numbers from AREA5 to AREA8). If you change the mask color,
the registered mask color will be changed automatically
with the same color for each of group (AREA1 to AREA4,
AREA5 to AREA8).
Menu Operation
Special Menu Settings
This menu lets you adjust and set up LANGUAGE, COLOR
EFFECT, SHARPNESS, STABILIZER, D-ZOOM, D-EFFECT,
MOTION DET, FACTORY RESET function by yourself in the
SPECIAL menu.
1.
Select [SPECIAL] option.
2.
Press [SET] button and the SPECIAL menu appears.
LANGUAGE Setting
Select the viewer language for the camera setup menu and
OSD information display.
1.
Select [LANGUAGE] option on the [SPECIAL] screen.
2.
Press [LEFT] or [RIGHT] button to select a language.
29
Menu Operation
Setting the COLOR
Setting the SHARPNESS effect
You can switch the displayed picture to gray scale or color.
The degree to which the boundary of the two portions is
clearly distinguished.
1.
Select [COLOR] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to change a color effect.
1.
Select [SHARPNESS] option on the [SPECIAL] menu.
t
ON: To display the picture with color.
2.
t
OFF: To display the picture with grayscale.
Use [LEFT] or [RIGHT] button to change a adjust
the option. If you set the sharpness value to higher,
the image outline becomes sharp. If you set to lower
value, the image outline becomes dim.
30
Menu Operation
STABILIZER setting
Setting the D-ZOOM (Digital Zoom ) level
You can select the digital zoom level.
The image stabilizer function minimizes the appearance of
shaky images caused by low-frequency vibration.
1.
Select [D-ZOOM] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to select a [ON] then
press [SET] the DIGITAL ZOOM menu appears. When
you set to ON, the displayed image can be shaking.
3.
Use [UP] or [DOWN] to select a option then use
[LEFT] or [RIGHT] button to select a level.
This function is useful for outdoor surveillance.
Select [STABILIZER] option and set to ON or OFF.
Note:
If you set the [STABILIZER] to ON, the Digital zoom is set to
[x1.1] automatically.
t
ZOOM: Use [LEFT] or [RIGHT] button to enlarge
the screen.
t
PAN: Use [LEFT] or [RIGHT] button to move the
screen. (left or right)
31
Menu Operation
t
TILT: Use [LEFT] or [RIGHT] button to move the
screen. (up or down)
Setting the D-EFFECT (Digital effect)
Motion Detection Setting
The motion detection detects the moving objects in the
scene by monitoring changes in brightness level. You can
select the level of sensitivity for motion detection to 4 zone.
You can select the digital effect.
1.
Select [D-EFFECT] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to select a digital effect.
32
t
V-FLIP: Flip the picture vertically.
t
MIRROR: Turn on the mirror effect.
t
ROTATE: Rotate the picture. (180°)
t
OFF: Turn off the digital effect.
1.
Select [MOTION DET] option.
2.
Use [LEFT] or [RIGHT] button to select a [ON] and
press [SET].
The MOTION DETECTION menu appears.
3.
Use [LEFT] or [RIGHT] button to select a zone number
(AREA1 to AREA4) on the [ZONE NUMBER].
4.
Use [LEFT] or [RIGHT] button to set up the ON or OFF
on the ZONE STATE.
Menu Operation
5.
6.
Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
t
HEIGHT: Enlarge or decrease the vertical size of
the mask.
t
WIDTH: Enlarge or decrease the horizontal size of
the mask.
t
MOVE Y: Moves vertical position of the mask.
t
MOVE X: Moves horizontal position of the mask.
Factory Reset Setting
1.
Select [FACTORY RESET] option on the [SPECIAL]
menu.
2.
Press [SET] button to reset the camera setting to
factory setting.
Use [SENSITIVITY] option to obtain the optimum
detection level.
33
Specification
Item
Signal System
Total/Effective Pixels
Image Device
DSP
Lens
Digital Zoom
IRIS Control
Synchronization System
Scanning Frequency (H/V)
Horizontal Resolution
S/N Ratio
Minimum Illumination
(30 IRE)
Control Method
Video Output Signal
Day & Night
BACKLIGHT
DNR
L5223 Series
PAL
470 000 Pixels / 440 000 Pixels
NTSC
410 000 Pixels / 380 000 Pixels
6 mm CCD
XDI-S2
2.8 mm to 11 mm Vari-focal lens
X8
DC / ELC
Internal
15.625 kHz / 50 Hz
15.734 kHz / 59.94 Hz
600 TV Lines
52 dB
0.1 lx @ Sens-up OFF, F1.2, Color
0.00003 lx @ Sens-up Auto, F1.2, BW
Inner Key Button
1 Vp-p Composite (75 Ω)
Digital Day & Night (DAY / NIGHT / AUTO)
OFF / WDR/ BLC / HSBLC
3D-DNR (OFF/LOW/MIDDLE/HIGH)
34
Specification
Item
Auto Gain Control
Electronic Shutter Speed
Electronic Sensitivity
White Balance
Motion Detection
Privacy Zone Masking
Stabilizer( EIS)
User Color Mode
Power Source
Power Consumption
Operation Temp.
Storage Temp.
Operation Humidity
Storage Humidity
Weight
Dimension (Ø x H)
35
L5223 Series
OFF / LOW / MIDDLE / HIGH
1/50 to 1/100 000
1/60 to 1/100 000
OFF/AUTO (X2, X3, X4, ..., X128)
ATW / AWC / PUSH / Manual
4 Zones
8 Masks
On / Off
STANDARD/COOL/WARM/VIVID
DC 12 V / AC 24 V
290 mA
-10 ºC to 50 ºC
-20 ºC to 60 ºC
0 % RH to 80 % RH
0 % RH to 85 % RH
350 g
140 mm x 87.3 mm
Download PDF

advertising