LG | L6223-BP | LG L6223-BP Owner’s Manual

OWNER'S MANUAL
Color Video Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
L6223 Series
P/NO : MFL67259822
1104(V1.0)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s enclosure
that may be of sufficient magnitude
to constitute a risk of electric shock to
persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
2
FCC WARNING: This equipment may generate or use
radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the
modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is
made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
•
A suitable conduit entries, knock-outs or glands shall
be provided in the cable entries of this product in the
end user.
•
•
Caution: Danger of explosion if battery is incorrectly
replaced. Replaced only with the same or equivalent
type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s
instructions.
Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall be
provided with brushings.
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
Caution: This installation should be made by a qualified
service person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
To disconnect power from mains, pull out the mains
cord plug. When installing the product, ensure that the
plug is easily accessible.
Warning: Do not install this equipment in a confined space
such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the
National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
Warning: To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
3
Disposal of your old appliance
1.
When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by the
European Directive 2002/96/EC.
2.
All electrical and electronic products
should be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or the
local authorities.
3.
The correct disposal of your old
appliance will help prevent potential
negative consequences for the
environment and human health.
4.
For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you
purchased the product.
EEE Compliance with Directive. (for Turkey only)
4
LG Electronics hereby declares that this/
these product(s) is/are in compliance
with the essential requirements and other
relevant provisions of Directive 2004/108/
EC, 2006/95/EC, and 2009/125/EC.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : +31-(0)36-547-8888)
Important Safety Instructions
1.
Read these instructions.
and the point where they exit from the apparatus.
2.
Keep these instructions.
3.
Heed all warnings.
11. Only use attachments/accessories specified by the
manufacturer.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
5
Cautions for Safe Operation
Power Supply
Operating and storage location
This camera must always be operated a AC 24 V or DC 12 V
Certified/Listed, class 2 power supply only.
Avoid viewing a very bright object (such as light fittings)
during an extended period. Avoid operating or storing the
unit in the following locations.
Handling of the unit
Be careful not to spill water or other liquids on the unit. Be
cautions not to get combustible or metallic material inside
the body. If used with foreign matter inside, the camera is
liable to fail or to get cause of fire or electric shock.
•
Remove dust or dirt on the surface of the lens with a
blower.
•
Use a dry soft cloth to clean the body. If it is very dirty,
use a cloth dampened with a small quantity of neutral
detergent then wipe dry.
•
Avoid the use of volatile solvents such as thinners,
alcohol, benzene and insecticides. They may damage
the surface finish and/or impair the operation of the
camera.
6
•
Extremely hot or cold places (operating temperature
-10 °C to 50 °C, however, we recommend that the unit
be used within a temperature range of 0 °C to 45 °C)
•
Damp or dust place
•
Places exposed to rain
•
Places subject to strong vibration
•
Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
Contents
Features.............................................................................. 8
Accessories................................................................................... 8
SENS-UP setting.............................................................28
White Balance settings..........................................................28
Part Names and Functions................................................ 9
3D-DNR Setting........................................................................30
Connections..................................................................... 11
Day/Night Setting...................................................................30
Basic connection......................................................................11
Privacy Setting..........................................................................31
Installation....................................................................... 12
Special Menu Settings...........................................................32
Mounting the Camera............................................................12
LANGUAGE Setting.......................................................33
Setting the COLOR.........................................................33
Setting the SHARPNESS effect..................................34
STABILIZER setting.........................................................34
Setting the D-ZOOM (Digital Zoom ) level ..........35
Setting the D-EFFECT (Digital effect) ....................35
Motion Detection Setting . ........................................36
Reset Settings ................................................................37
Specification.................................................................... 38
Wall mount (Optional)...........................................................16
Image Adjustment..................................................................17
Menu Operation.............................................................. 21
OSD Menu Overview..............................................................22
General Operation...................................................................24
Setting the USER TITLE...........................................................24
Exposure Settings....................................................................25
WDR/BLC setting............................................................25
BRIGHTNESS setting......................................................26
AGC (Automatic Gain Control) setting...................27
SHUTTER (Shutter Speed) setting............................27
7
Features
This Color Video Camera is designed for installation in a
video surveillance system.
This manual contains instructions on how to install and
manage the Color Video Camera in your video surveillance
system.
Should you require any technical assistance, please contact
authorized service center.
•
High resolution and high sensitivity with a 6 mm CCD.
•
Day & Night function.
•
WDR/BLC covers various light conditions.
•
Excellent signal-to-noise ratio of 52 dB.
•
Weather Proof: IP66 Rating.
•
Dome Cover : Vandal -Proof.
Accessories
Installation sticker
Camera mounting
bracket
Wrench
M4 Fixing screws
8
Part Names and Functions
a Dome Cover
b Lens Cover
c Focus lock lever
a
Fixes the focus position after adjusting.
d Zoom lock lever
Fixes the zoom position after adjusting.
e Azimuth adjuster
b
Adjusts the azimuth angle to obtain a level image.
f Tilting lock screw
Fixes the tilting position after adjusting.
c
d
e
f
g
h
g Azimuth lock screw
Fixes the azimuth angle after adjusting.
h Video Out connector
Use this jack for checking the picture with portable
monitor when install the camera.
i Setup menu control buttons
i
9
Part Names and Functions
j Pan adjuster
Adjusts the pan position.
k Pan lock screw
j
k
l
m
n
Fixes the panning position after adjusting.
l Power input connector
Supplies AC 24 V or DC 12 V from an external power
source.
m Video output connector (BNC type)
n Camera mounting bracket
This bracket is supplied for ceiling installation.
10
Connections
Basic connection
2. Connect a external power source to the power input
jack of the camera.
The peripheral devices (DVR, monitor, etc.), AC/DC adapter
and cables are not supplied.
1. Make the video signal connection between the
camera and the monitor or DVR.
11
Installation
Mounting the Camera
You can mount the camera on a ceiling or wall.
Surface mount
Follow the instructions below to surface mount the camera
with supplied camera mounting bracket.
1.
12
Use the installation guide template to check the
mounting location. Face the front of the label toward
the area of interest. Using the template as a guide,
make a hole through the ceiling.
2.
Pass the connection cable through the inner side of
the ceiling.
Installation
3.
Install the camera mounting bracket to the ceiling.
4.
Connect the cables to the cable jacks of the camera
body.
13
Installation
5.
Assemble the camera and mounting bracket. Connect
the unit by following step a and b.
Wall mount with optional mounting
bracket housing
Follow the instructions below to surface mount the camera.
with optional mounting bracket housing.
1.
14
Install the mounting bracket housing to the ceiling.
Installation
2.
Fasten the camera mounting bracket to the mounting
bracket housing.
3.
Assemble the camera and mounting bracket. Connect
the unit by following step a and b.
15
Installation
Wall mount (Optional)
Follow the instructions below to install the camera with a
wall mount.
1. Drill holes in the wall where you want to install the
wall mount.
2. Install the wall mount and camera installation bracket
assembly as shown below.
Pipe threads should be
clean and rust free. Use
a sealer (such as Teflon™
tape and silicone sealer)
on the threads.
16
3. Connect the cables to the camera jack and attach the
camera to the camera installation bracket assembly.
Installation
4.
Attach the camera to the installation bracket assembly.
Image Adjustment
You can manually adjust the pan/tilt/azimuth angles, focus,
and zoom while observing the connected monitor.
Notes:
•
Do not hold the camera by lens unit to adjust panning,
tilting, or azimuth.
•
The video output to the BNC will be interrupted while
a portable monitor is connected to the video jack.
1. Use the supplied wrench to loosen the screws and
remove the dome cover Remove the Dome cover and
lans cover.
17
Installation
2. Connect a portable monitor to the video jack.
3.
Adjust the pan/tilt position of the camera.
3-1. Loosen the pan/tilt lock screw.
3-2. Lock the pan/tilt lock screw after adjusting.
18
Installation
4.
Adjust the azimuth angle.
5.
Adjust the zoom.
4-1. Loosen the azimuth angle lock screw.
5-1. Unlock the zoom lever.
4-2. Lock the azimuth angle lock screw after adjusting.
5-2. Move the lever to adjust the zoom.
5-3. Lock the lever.
NEAR
FAR
WIDE
TELE
19
Installation
6. Adjust the focus.
6-1. Unlock the focus lever.
6-2. Move the lever to adjust the focus.
6-3. Lock the lever.
NEAR
7. Attach the lens cover and dome cover.
20
FAR
Menu Operation
This camera utilizes an on-screen user MENU. To set items
on the menu, use the following buttons.
•
UP button:
Used to move upper direction on the menu screen.
Use this button to select an item or adjust the parameters.
•
DOWN button:
Used to move lower direction on the menu screen. Use
this button to select an item or adjust the parameters.
•
RIGHT button:
Moves the cursor to the right. Used to increment the
value selected in the menu. The parameter changes
each time this button is pressed.
•
Moves the cursor to the left. Used to decrement the
value selected in the menu. The parameter changes
each time this button is pressed.
DOWN
SET
RIGHT
UP
LEFT button:
LEFT
•
SET button:
Executes selections and displays a submenu for an
item with the mark.
21
Menu Operation
OSD Menu Overview
The following table shows the list of menu items and options. You can adapt the camera to your requirements by
setting up the respective items in these menus.
Main Menu
USER TITLE
Sub Menu
Contents
OFF
-
ON
WDR / BLC
BRIGHTNESS
AGC
EXPOSURE
ALC /ELC /ALC2
SHUTTER
Sub Menu
EXPOSURE
ALC / ELC / ALC2
SENS-UP
ATW
USER MODE
Contents
OFF
AUTO
STANDARD
VIVID
WARM
COOL
WHITE BAL
OFF/WDR/BLC/
HSBLC
1/100 000, ..., 1/160,
A.FLK, OFF, AUTO, x2,
..., x512
(for ALC/ELC mode)
AWC / PUSH
INDOOR,
OUTDOOR
-100 to 100
COLOR TEMP
MANUAL
0 to 100
OFF/LOW/MIDDLE/
HIGH
A.FLK,1/160, ...,
1/100 000
(for ALC2 mode)
22
Main Menu
RED
BLUE
3D-DNR
-100 to 100
OFF
-
LOW
-
MIDDLE
-
HIGH
LOW/ MIDDLE/
HIGH
5, 10, 15, 30,
60 SEC
LEVEL
AUTO
DWELL TIME
DAY/NIGHT
DAY
-
NIGHT
-
Menu Operation
Main Menu
PRIVACY
Sub Menu
Contents
OFF
-
ON
Main Menu
Sub Menu
LANGUAGE
Contents
ENG/CHN/KOR/JAP/FRE/ITA/SPA/POR/
DUT/GER/POL/RUS/TUR/ARA/HEB
MASK NUMBER
AREA1 to AREA8
DISPLAY SET
ON/OFF
SHARPNESS
0 to 68
COLOR SET
GRAY/ WHITE/
BLACK
STABILIZER
OFF/ ON
HEIGHT
4 to 100
WIDTH
4 to 100
MOVE Y
2 to 98
MOVE X
2 to 98
COLOR EFFECT
OFF/ ON
OFF
D-ZOOM
SPECIAL
D-EFFECT
ZOOM
PAN
TILT
ON
OFF/ V-FLIP/ MIRROR/ ROTATE
OFF
MOTION DET
ON
EXIT
ZONE
NUMBER
ZONE STATE
HEIGHT
WIDTH
MOVE Y
MOVE X
SENSITIVITY
FACTORY RESET
-
-
-
AREA1 to
AREA4
OFF/ON
12 to 100
16 to 100
6 to 94
8 to 92
0 to 100
23
Menu Operation
General Operation
1.
Press [SET] button.
The setup menu screen appears on the monitor.
2.
Use [UP] or [DOWN] button to select an option then
press [SET] button.
Submenu appears on the monitor.
3.
Use [UP] or [DOWN] button to select a submenu
option.
4.
Use [LEFT] or [RIGHT] button to select a value.
5.
Select [EXIT] option then press [SET] to exit the setup
menu. In the submenu, use [UP] or [DOWN] button to
select the [RETURN] then press [SET] to return to the
previous setup menu.
•
24
RETURN: Return to the previous.
Setting the USER TITLE
You can use the camera identification to assign a number
and character to the camera.
The USER TITLE is displayed on the upper left of the screen.
To disappear the user title, select [OFF].
1.
Select [USER TITLE] option.
2.
Use [LEFT] or [RIGHT] button to select a [ON] then
press [SET]. The USER TITLE menu appears.
A
3.
Use [UP], [DOWN], [LEFT] or [RIGHT] button to select
a character or number then press [SET] button.
•
CLR: Clear all entered characters and numbers.
•
POS: Move the USER TITLE position on the screen
using the arrow buttons.
Menu Operation
•
END: Confirm your selection or exit the setting
WDR/BLC setting
•
A (Blank): Inserts a space at the cursor position.
Use WDR/BLC option to view the object clearly in backlight
conditions.
•
/
: Moves cursor to left or right.
Exposure Settings
You can set the exposure options using the EXPOSURE
menu.
1.
Select [EXPOSURE] option on the [CAMERA SETTING]
menu.
2.
Use [LEFT] or [RIGHT] button to select a mode.
3.
Press [SET] button and the EXPOSURE menu appears.
1.
Select [WDR/BLC] option.
2.
Use [LEFT] or [RIGHT] button to select a mode then
press [SET].
•
WDR: WDR (Wide dynamic range) feature can
be very helpful to cope with very challenging
lighting conditions. It is capable of capturing
both of the dark part and bright part and
combining the differences into a scene to
generate a highly realistic image as original
scene. Set the WDR limit.
25
Menu Operation
•
•
BLC: Camera's backlight compensation feature
helps alleviate issues of visibility in high contrast
areas. Set the BLC limit.
HSBLC: Use for masking brightness of the specific
area to view the subject more clearly. The HSBLC
mode is automatically activated only in low
luminance scene.
AREA SETTING: Use [LEFT] or [RIGHT]
button to select a area then use [UP] or
[DOWN] button to select a [ON] or [OFF].
Press [SET] to exit the Area setting menu.
>> GRAY SCALE: Use [LEFT] or [RIGHT] button
to select a gray scale. (GRAY, D.GRAY, BLACK)
>> USER SCALE: Use [LEFT] or [RIGHT] button
to select a bright level. (5 level)
>> MASK: Use [LEFT] or [RIGHT] button to
select [ON] or [OFF].
If you set the MASK to ON, the mask
function is activate only when the HSBLC is
automatically activated in low luminance
scene.
OFF: Not used.
BRIGHTNESS setting
You can increase the brightness of the darkened video.
If you set the brightness to lower value, the image is
darkened. If you set the brightness to higher value, the
image gets bright.
>>
•
26
1.
Select [BRIGHTNESS] option.
2.
Use [LEFT] or [RIGHT] button to set the bright level.
Menu Operation
AGC (Automatic Gain Control) setting
SHUTTER (Shutter Speed) setting
If the images are too dark, change the maximum [AGC]
value to make the images brighter.
Select the desired shutter speed for camera exposure. You
can change the shutter speed to higher speed to capture
fast-moving subjects, though the image becomes darker.
1.
Select [AGC] option.
2.
Use [LEFT] or [RIGHT] button to select a mode.
1.
Select [SHUTTER] option.
2.
Use [LEFT] or [RIGHT] button to set shutter speed.
Note:
If you set the shutter speed value in ALC2 mode, it is
maximum value. When the camera is activated with
ALC2 mode, the shutter speed is arrived maximum
value and then the camera is change to iris control mode
automatically for the camera exposure.
27
Menu Operation
SENS-UP setting
Note:
If pictures are not clear due to darkness, this SENS-UP
operation would increase the sensitivity of picture.
If you set to one of the SHUTTER options except AUTO
on the [SHUTTER] menu or [AGC] to [OFF], the [SENS-UP]
setting is not available and [---] mark is displayed.
White Balance settings
Select the method by which the camera shifts its output
colors to compensate for the color of a light source.
1.
Use [UP] or [DOWN] button to select [SENS-UP]
option.
2.
Use [LEFT] or [RIGHT] button to select mode.
•
AUTO: Adjust the sensitivity of the picture
automatically.
>>
•
28
SENS-UP LIMIT: Use [LEFT] or [RIGHT]
button to set the SENS-UP limit.
OFF: Not used.
1.
Select [WHITE BAL] option.
2.
Use [LEFT] or [RIGHT] button to select a mode then
press [SET].
Menu Operation
•
ATW (Auto-Tracing White Balance): Use [LEFT]
or [RIGHT] button to select the ATW then press
[SET] button.
You can select the USER MODE.
--
>>
>>
•
AWC/PUSH: If you select the AWC/PUSH
mode, you will be able to set up the White
Balance automatically using [SET] button.
•
MANUAL: You can set the white balance options
manually.
>>
INDOOR: The color temperature
range for the proper white balance is
approximately 3 200 K.
-OUTDOOR: The color temperature
range for the proper white balance is
approximately 5 100 K.
RED: Obtains the optimum amount of red
gain.
BLUE: Obtains the optimum amount of blue
gain.
COLOR TEMP: Use [LEFT] or [RIGHT] button
to select a function.
29
Menu Operation
3D-DNR Setting
Day/Night Setting
1.
1.
Select [DAY/NIGHT] option.
2.
Use [LEFT] or [RIGHT] button to select mode
for Day/Night function.
2.
Select [3D-DNR] option.
If pictures are not clear due to brightness, this option
would reduce the noise of picture.
Use [LEFT] or [RIGHT] button to select a option.
Notes:
•
If you set the AGC to [OFF] on the [EXPOSURE] menu,
the [3D-DNR] function is not available and [---] mark
is displayed.
•
When you use this function, the afterimage may occur.
30
•
AUTO: You will be able to change the Day/Night
mode automatically.
Note:
If you set the AGC to [OFF] or the SHUTTER is set
to one of the SHUTTER options except AUTO on
the [EXPOSURE] menu, the AUTO mode of the
DAY/NIGHT function is not available and [---]
mark is displayed.
Menu Operation
•
LEVEL: Use [LEFT] or [RIGHT] button to
select a level.
>> DWELL TIME: Use [LEFT] or [RIGHT] button
to select a dwell time.
DAY: Color mode enabled.
•
NIGHT: Black-and-white mode enabled.
>>
Privacy Setting
This function is aiming at the protection of personal
privacy, selecting a screen part black not to be displayed in
the screen. Up to 8 zones can be registered.
1.
Select [PRIVACY] option.
2.
Use [LEFT] or [RIGHT] button to select a [ON] and
press [SET]. The PRIVACY SETUP menu appears.
3.
Use [LEFT] or [RIGHT] button to select a mask (AREA1
to AREA8) on the [MASK NUMBER].
4.
Use [LEFT] or [RIGHT] button to set up the ON or OFF
on the DISPLAY SET option.
31
Menu Operation
5.
Use [LEFT] or [RIGHT] button to set up the GRAY,
WHITE or BLACK on the COLOR SET option.
Special Menu Settings
6.
Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
This menu lets you adjust and set up LANGUAGE, COLOR
EFFECT, SHARPNESS, STABILIZER, D-ZOOM, D-EFFECT,
MOTION DET, FACTORY RESET function by yourself in the
SPECIAL menu.
•
HEIGHT: Enlarge or decrease the vertical size of
the mask.
•
WIDTH: Enlarge or decrease the horizontal size of
the mask.
•
MOVE Y: Moves vertical position of the mask.
•
MOVE X: Moves horizontal position of the mask.
Note:
The parts with the registered mask numbers from AREA1
to AREA4 have the same color. (So do the parts with
the numbers from AREA5 to AREA8). If you change the
mask color, the registered mask color will be changed
automatically with the same color for each of group (AREA1
to AREA4, AREA5 to AREA8).
32
1.
Select [SPECIAL] option.
2.
Press [SET] button and the SPECIAL menu appears.
Menu Operation
LANGUAGE Setting
Setting the COLOR
Select the viewer language for the camera setup menu and
OSD information display.
You can switch the displayed picture to gray scale or color.
1.
Select [LANGUAGE] option on the [SPECIAL] screen.
2.
Press [LEFT] or [RIGHT] button to select a language.
1.
Select [COLOR] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to change a color effect.
•
ON: To display the picture with color.
•
OFF: To display the picture with grayscale.
33
Menu Operation
Setting the SHARPNESS effect
STABILIZER setting
The degree to which the boundary of the two portions is
clearly distinguished.
1.
Select [SHARPNESS] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to change a adjust
the option. If you set the sharpness value to higher,
the image outline becomes sharp. If you set to lower
value, the image outline becomes dim.
34
The image stabilizer function minimizes the appearance of
shaky images caused by low-frequency vibration.
This function is useful for outdoor surveillance.
Select [STABILIZER] option and set to ON or OFF.
Note:
If you set the [STABILIZER] to ON, the Digital zoom is set to
[x1.1] automatically.
Menu Operation
Setting the D-ZOOM (Digital Zoom ) level
•
You can select the digital zoom level.
TILT: Use [LEFT] or [RIGHT] button to move the
screen. (up or down)
Setting the D-EFFECT (Digital effect)
You can select the digital effect.
1.
Select [D-ZOOM] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to select a [ON] then
press [SET] the DIGITAL ZOOM menu appears. When
you set to ON, the displayed image can be shaking.
3.
Use [UP] or [DOWN] to select a option then use
[LEFT] or [RIGHT] button to select a level.
•
•
1.
Select [D-EFFECT] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to select a digital effect.
ZOOM: Use [LEFT] or [RIGHT] button to enlarge
the screen.
•
V-FLIP: Flip the picture vertically.
PAN: Use [LEFT] or [RIGHT] button to move the
screen. (left or right)
•
MIRROR: Turn on the mirror effect.
•
ROTATE: Rotate the picture. (180°)
•
OFF: Turn off the digital effect.
35
Menu Operation
Motion Detection Setting
[LEFT] or [RIGHT] button to adjust the option.
The motion detection detects the moving objects in the
scene by monitoring changes in brightness level. You can
select the level of sensitivity for motion detection to 4 zone.
•
HEIGHT: Enlarge or decrease the vertical size of
the mask.
•
WIDTH: Enlarge or decrease the horizontal size of
the mask.
•
MOVE Y: Moves vertical position of the mask.
•
MOVE X: Moves horizontal position of the mask.
6.
1.
Select [MOTION DET] option.
2.
Use [LEFT] or [RIGHT] button to select a [ON] and
press [SET].
The MOTION DETECTION menu appears.
3.
Use [LEFT] or [RIGHT] button to select a zone number
(AREA1 to AREA4) on the [ZONE NUMBER].
4.
Use [LEFT] or [RIGHT] button to set up the ON or OFF
on the ZONE STATE.
5.
Use [UP] or [DOWN] to select an option then use
36
Use [SENSITIVITY] option to obtain the optimum
detection level.
Menu Operation
Factory Reset Setting
1.
Select [FACTORY RESET] option on the [SPECIAL]
menu.
2.
Press [SET] button to reset the camera setting to
factory setting.
37
Specification
Item
Signal System
Total/Effective Pixels
Image Device
DSP
Lens
Digital Zoom
IRIS Control
Sync. System
Scanning Frequency (H/V)
Horizontal Resolution
S/N Ratio
38
L6223 Series
PAL
470 000 Pixels / 440 000 Pixels
NTSC
410 000 Pixels / 380 000 Pixels
6 mm CCD
XDI-S2
2.8 mm to 11 mm Vari-focal lens
X8
DC / ELC
Internal
15.625 kHz / 50 Hz
15.734 kHz / 59.94 Hz
600 TV Lines
52 dB
0.1 lx @ Sens-up OFF, F1.2, Color
Minimum Illumination
(30 IRE)
0.000 03 lx @ Sens-up Auto, F1.2, BW
Control Method
Video Output Signal
Day & Night
Inner Key Button
1 Vp-p Composite (75 Ω)
DAY / NIGHT / AUTO
BACKLIGHT
OFF / WDR / BLC / HSBLC
Specification
Item
L6223 Series
DNR
Auto Gain Control
Electronic Shutter Speed
Electronic Sensitivity
White Balance
Motion Detection
Privacy Zone Masking
Stabilizer( EIS)
User Color Mode
Power Source
Power Consumption
Operation Temp.
Storage Temp.
Operation Humidity
Storage Humidity
Weight
Dimension (Ø x H)
3D-DNR (Off/Low/Middle/High)
Off / Low / Middle / High
1/50 to 1/100 000
1/60 to 1/100 000
OFF/Auto (x2, x3, x4, ..., x128)
ATW / AWC / PUSH / Manual
4 Zones
8 Masks
On / Off
STANDARD/COOL/WARM/VIVID
DC 12 V / AC 24 V
290 mA
-10 ºC to 50 ºC
-20 ºC to 60 ºC
0 % RH to 80 % RH
0 % RH to 85 % RH
640 g
140 mm x 91.7 mm
39
Download PDF