OWNER'S MANUAL
Color Video Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
L6213-BN
L6213-BP
L6213-DN
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.
2
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if
an unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
•
A suitable conduit entries, knock-outs or glands shall
be provided in the cable entries of this product in the
end user.
•
•
Caution: Danger of explosion if battery is incorrectly
replaced. Replaced only with the same or equivalent
type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s
instructions.
Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall be
provided with brushings.
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
Caution: This installation should be made by a qualified
service person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
To disconnect power from mains, pull out the mains
cord plug. When installing the product, ensure that the
plug is easily accessible.
Warning: Do not install this equipment in a confined space
such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the
National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Warning: To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
3
Disposal of your old appliance
4
1.
When this crossed-out wheeled bin
symbol is attached to a product it means
the product is covered by the European
Directive 2002/96/EC.
2.
All electrical and electronic products
should be disposed of separately from
the municipal waste stream via designated collection facilities appointed by
the government or the local authorities.
3.
The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and
human health.
4.
For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you purchased the product.
LG Electronics hereby declares that this/these
product(s) is/are in compliance with the essential requirements and other relevant provisions
of Directive 2004/108/EC, 2006/95/EC, and
2009/125/EC.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : +31-(0)36-547-8888)
Important Safety Instructions
1.
Read these instructions.
and the point where they exit from the apparatus.
2.
Keep these instructions.
3.
Heed all warnings.
11. Only use attachments/accessories specified by the
manufacturer.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
5
Cautions for Safe Operation
Power Supply
L6213-BP/L6213-BN:
This camera must always be operated a AC 24 V or DC 12 V
Certified/Listed, class 2 power supply only.
L6213-DN:
This camera must always be operated a DC 12 V
Certified/Listed, class 2 power supply only.
Handling of the unit
Be careful not to spill water or other liquids on the unit. Be
cautions not to get combustible or metallic material inside
the body. If used with foreign matter inside, the camera is
liable to fail or to get cause of fire or electric shock.
•
Remove dust or dirt on the surface of the lens with a
blower.
•
Use a dry soft cloth to clean the body. If it is very dirty,
use a cloth dampened with a small quantity of neutral
detergent then wipe dry.
6
•
Avoid the use of volatile solvents such as thinners,
alcohol, benzene and insecticides. They may damage
the surface finish and/or impair the operation of the
camera.
Operating and storage location
Avoid viewing a very bright object (such as light fittings)
during an extended period. Avoid operating or storing the
unit in the following locations.
•
Extremely hot or cold places (operating temperature
-10 °C to 50 °C, however, we recommend that the unit
be used within a temperature range of 0 °C to 45 °C)
•
Damp or dust place
•
Places exposed to rain
•
Places subject to strong vibration
•
Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
Contents
Features.............................................................................. 8
Accessories................................................................................... 8
SENS-UP setting.............................................................28
White Balance settings..........................................................28
Part Names and Functions................................................ 9
3D-DNR Setting........................................................................30
Connections..................................................................... 11
Day/Night Setting...................................................................30
Basic connection......................................................................11
Privacy Setting..........................................................................31
Installation....................................................................... 12
Special Menu Settings...........................................................32
Mounting the Camera............................................................12
LANGUAGE Setting.......................................................33
Setting the COLOR EFFECT.........................................33
Setting the SHARPNESS effect..................................34
STABILIZER setting.........................................................34
Setting the D-ZOOM (Digital Zoom ) level ..........35
Setting the D-EFFECT (Digital effect) .....................35
Motion Detection Setting...........................................36
Factory Reset Setting...................................................37
Specification.................................................................... 38
Wall mount (Optional)...........................................................16
Image Adjustment..................................................................17
Menu Operation.............................................................. 21
OSD Menu Overview..............................................................22
General Operation...................................................................24
Setting the USER TITLE...........................................................24
Exposure Settings....................................................................25
BACKLIGHT setting........................................................25
BRIGHTNESS setting......................................................26
AGC (Automatic Gain Control) setting...................27
SHUTTER (Shutter Speed) setting............................27
7
Features
This Color Video Camera is designed for installation in a
video surveillance system.
This manual contains instructions on how to install and
manage the Color Video Camera in your video surveillance
system.
Should you require any technical assistance, please contact
authorized service center.
•
High resolution and high sensitivity with a 6 mm CCD.
•
Day & Night function.
•
BLC covers various light conditions.
•
Excellent signal-to-noise ratio of 52 dB.
•
Weather Proof: IP66 Rating.
•
Dome Cover : Vandal -Proof.
Accessories
Installation sticker
Camera mounting
bracket
Wrench
M4 Fixing screws
8
Part Names and Functions
a Dome Cover
b Lens Cover
c Focus lock lever
a
Fixes the focus position after adjusting.
d Zoom lock lever
Fixes the zoom position after adjusting.
e Azimuth adjuster
b
Adjusts the azimuth angle to obtain a level image.
f Tilting lock screw
Fixes the tilting position after adjusting.
c
d
e
f
g
h
g Azimuth lock screw
Fixes the azimuth angle after adjusting.
h Video Out connector
Use this jack for checking the picture with portable
monitor when install the camera.
i Setup menu control buttons
i
9
Part Names and Functions
j Pan adjuster
Adjusts the pan position.
k Pan lock screw
j
k
l
m
n
Fixes the panning position after adjusting.
l Power input connector
Supplies AC 24 V or DC 12 V from an external power
source.
m Video output connector (BNC type)
n Camera mounting bracket
This bracket is supplied for ceiling installation.
10
Connections
Basic connection
2. Connect a external power source to the power input
jack of the camera.
The peripheral devices (DVR, monitor, etc.), AC/DC adapter
and cables are not supplied.
1. Make the video signal connection between the camera and the monitor or DVR.
11
Installation
Mounting the Camera
You can mount the camera on a ceiling or wall.
Surface mount
Follow the instructions below to surface mount the camera
with supplied camera mounting bracket.
1.
12
Use the installation guide template to check the
mounting location. Face the front of the label toward
the area of interest. Using the template as a guide,
make a hole through the ceiling.
2.
Pass the connection cable through the inner side of
the ceiling.
Installation
3.
Install the camera mounting bracket to the ceiling.
4.
Connect the cables to the cable jacks of the camera
body.
13
Installation
5.
Assemble the camera and mounting bracket. Connect
the unit by following step a and b.
Wall mount with optional mounting
bracket housing
Follow the instructions below to surface mount the camera.
with optional mounting bracket housing.
1.
14
Install the mounting bracket housing to the ceiling.
Installation
2.
Fasten the camera mounting bracket to the mounting
bracket housing.
3.
Assemble the camera and mounting bracket. Connect
the unit by following step a and b.
15
Installation
Wall mount (Optional)
3. Connect the cables to the camera jack and attach the
camera to the camera installation bracket assembly.
Follow the instructions below to install the camera with a
wall mount.
1. Drill holes in the wall where you want to install the
wall mount.
2. Install the wall mount and camera installation bracket
assembly as shown below.
“A”
16
Installation
4.
Attach the camera to the installation bracket assembly.
Image Adjustment
You can manually adjust the pan/tilt/azimuth angles, focus,
and zoom while observing the connected monitor.
Notes:
•
Do not hold the camera by lens unit to adjust panning,
tilting, or azimuth.
•
The video output to the BNC will be interrupted while
a portable monitor is connected to the video jack.
1. Use the supplied wrench to loosen the screws and
remove the dome cover Remove the Dome cover and
lans cover.
17
Installation
2. Connect a portable monitor to the video jack.
3.
Adjust the pan/tilt position of the camera.
3-1. Loosen the pan/tilt lock screw.
3-2. Lock the pan/tilt lock screw after adjusting.
18
Installation
4.
Adjust the azimuth angle.
5.
Adjust the zoom.
4-1. Loosen the azimuth angle lock screw.
5-1. Unlock the zoom lever.
4-2. Lock the azimuth angle lock screw after adjusting.
5-2. Move the lever to adjust the zoom.
5-3. Lock the lever.
NEAR
FAR
WIDE
TELE
19
Installation
6. Adjust the focus.
6-1. Unlock the focus lever.
6-2. Move the lever to adjust the focus.
6-3. Lock the lever.
NEAR
7. Attach the lens cover and dome cover.
20
FAR
Menu Operation
This camera utilizes an on-screen user MENU. To set items
on the menu, use the following buttons.
•
UP button:
Used to move upper direction on the menu screen.
Use this button to select an item or adjust the parameters.
•
DOWN button:
Used to move lower direction on the menu screen. Use
this button to select an item or adjust the parameters.
•
RIGHT button:
Moves the cursor to the right. Used to increment the
value selected in the menu. The parameter changes
each time this button is pressed.
•
Moves the cursor to the left. Used to decrement the
value selected in the menu. The parameter changes
each time this button is pressed.
DOWN
SET
RIGHT
UP
LEFT button:
LEFT
•
SET button:
Executes selections and displays a submenu for an
item with the mark.
21
Menu Operation
OSD Menu Overview
Main Menu
Main Menu
USER TITLE
Sub Menu
Contents
OFF
-
ON
-
Sub Menu
Contents
STANDARD
The following table shows the list of menu items and options. You can adapt the camera to your requirements by
setting up the respective items in these menus.
ATW
AWC / PUSH
-
OFF/BLC/HSBLC
BRIGHTNESS
0 to 100
AGC
OFF/LOW/MIDDLE/
HIGH
SHUTTER
SENS-UP
22
INDOOR,
OUTDOOR
-100 to 100
COLOR TEMP
BACKLIGHT
ALC2/ALC/ELC
WARM
COOL
WHITE BAL
MANUAL
RED
BLUE
3D-DNR
x512,…,x2,AUTO,OFF,A.
FLK,1/160,…,1/90 000
(for ALC/ELC mode)
1/100(NTSC) or
1/120(PAL),…,1/90 000
(for ALC2 mode)
OFF
AUTO
-100 to 100
OFF
-
LOW
-
MIDDLE
-
HIGH
EXPOSURE
VIVID
USER MODE
LOW/ MIDDLE/
HIGH
5, 10, 15, 30,
60 SEC
LEVEL
AUTO
DWELL TIME
DAY/NIGHT
DAY
-
NIGHT
-
Menu Operation
Main Menu
PRIVACY
Sub Menu
Contents
OFF
-
ON
Main Menu
Sub Menu
LANGUAGE
Contents
ENG/CHN/KOR/JAP/FRE/ITA/SPA/POR/
DUT/GER/POL/RUS/TUR/ARA/HEB
MASK NUMBER
AREA1 to AREA8
DISPLAY SET
ON/OFF
SHARPNESS
0 to 68
COLOR SET
GRAY/ WHITE/
BLACK
STABILIZER
OFF/ ON
HEIGHT
4 to 100
WIDTH
4 to 100
MOVE Y
2 to 98
MOVE X
2 to 98
COLOR EFFECT
OFF/ ON
OFF
D-ZOOM
SPECIAL
D-EFFECT
ZOOM
PAN
TILT
ON
OFF/ V-FLIP/ MIRROR/ ROTATE
OFF
ZONE
NUMBER
MOTION DET
ON
EXIT
AREA1 to
AREA4
ZONE STATE
OFF/ON
HEIGHT
12 to 100
WIDTH
16 to 100
MOVE Y
6 to 94
MOVE X
8 to 92
SENSITIVITY
0 to 100
FACTORY RESET
-
-
-
23
Menu Operation
General Operation
Setting the USER TITLE
1.Press [SET] button.
The setup menu screen appears on the monitor.
You can use the camera identification to assign a number
and character to the camera (0 to 9, A to Z, a to z).
The USER TITLE is displayed on the upper left of the screen.
To disappear the user title, select [OFF].
1.
Select [USER TITLE] option.
2.Use [LEFT] or [RIGHT] button to select a [ON] then
press [SET]. The USER TITLE menu appears.
2.Use [UP] or [DOWN] button to select an option then
press [SET] button.
Submenu appears on the monitor.
A
3.Use [UP] or [DOWN] button to select a submenu
option.
4.Use [LEFT] or [RIGHT] button to select a value.
5.
Select [EXIT] option then press [SET] to exit the setup
menu. In the submenu, use [UP] or [DOWN] button to
select the [RETURN] then press [SET] to return to the
previous setup menu.
•
24
RETURN: Return to the previous.
3.Use [UP], [DOWN], [LEFT] or [RIGHT] button to select
a character or number then press [SET] button.
•
CLR: Clear all entered characters and numbers.
•
POS: Move the USER TITLE position on the screen
using the arrow buttons.
Menu Operation
•
END: Confirm your selection or exit the setting
•
A (Blank): Inserts a space at the cursor position.
•
/
: Moves cursor to left or right.
Exposure Settings
You can set the exposure options using the EXPOSURE
menu.
1.
Select [EXPOSURE] option on the [CAMERA SETTING]
menu.
2.Use [LEFT] or [RIGHT] button to select a mode.
ALC
ELC)
(ALC2
BACKLIGHT setting
Use BACKLIGHT option to view the object clearly in backlight conditions.
3.Press [SET] button and the EXPOSURE menu appears.
1.
Select [BACKLIGHT] option.
25
Menu Operation
2.Use [LEFT] or [RIGHT] button to select a mode then
press [SET].
•
•
BLC: Camera's backlight compensation feature
helps alleviate issues of visibility in high contrast
areas. Set the BLC limit.
MIDDLE
HIGH
>> BLC LIMIT: LOW
HSBLC: Use for masking brightness of the specific
area to view the subject more clearly. The HSBLC
mode is automatically activated only in low luminance scene.
>>
>>
>>
>>
26
AREA SETTING: Use [LEFT] or [RIGHT] button to select a area then use [UP] or [DOWN]
button to select a ON or OFF. Press [SET] to
exit the Area setting menu.
GRAY SCALE: Use [LEFT] or [RIGHT] button
to select a gray scale.
(GRAY
D.GRAY
BLACK).
USER SCALE: Use [LEFT] or [RIGHT] button
to select a bright level.(5 level)
MASK: Use [LEFT] or [RIGHT] button to
select [ON] or [OFF].
If you set the MASK to ON, the mask function
•
is activate only when the HSBLC is automatically activated in low luminance scene.
OFF: Not used.
BRIGHTNESS setting
You can increase the brightness of the darkened video. If
you set the brightness to lower value, the image is darkened. If you set the brightness to higher value, the image
gets bright.
1.
Select [BRIGHTNESS] option.
2.Use [LEFT] or [RIGHT] button to set the bright level.
Menu Operation
AGC (Automatic Gain Control) setting
If the images are too dark, change the maximum [AGC]
value to make the images brighter.
1.
1.
Select [AGC] option.
2.Use [LEFT] or [RIGHT] button to select a mode.
LOW
MIDDLE
HIGH)
(OFF
SHUTTER (Shutter Speed) setting
Select the desired shutter speed for camera exposure. You
can change the shutter speed to higher speed to capture
fast-moving subjects, though the image becomes darker.
Select [SHUTTER] option.
2.Use [LEFT] or [RIGHT] button to set shutter speed.
AUTO
OFF
(ALC/ELC mode: x512,…,x2
A.FLK
1/160,…,1/90 000
ALC2 mode: 1/100(NTSC) or 1/120(PAL),…,1/90 000)
Note:
If you set the shutter speed value in ALC2 mode, it is maximum value. When the camera is activated with ALC2 mode,
the shutter speed is arrived maximum value and then the
camera is change to iris control mode automatically for the
camera exposure. ALC2 mode doesn't support anti-flicker
shutter so If you want to use it, use it in ALC mode .
27
Menu Operation
SENS-UP setting
Note:
If pictures are not clear due to darkness, this SENS-UP
operation would increase the sensitivity of picture.
If you set to one of the SHUTTER options except AUTO on
the [SHUTTER] menu or [AGC] to [OFF], the [SENS-UP] setting is not available and [---] mark is displayed.
White Balance settings
Select the method by which the camera shifts its output
colors to compensate for the color of a light source.
1.Use [UP] or [DOWN] button to select [SENS-UP]
option.
2.Use [LEFT] or [RIGHT] button to select mode.
•
AUTO: Adjust the sensitivity of the picture automatically.
>>
•
28
SENS-UP LIMIT: Use [LEFT] or [RIGHT] button to set the SENS-UP limit.
OFF: Not used.
1.
Select [WHITE BAL] option.
2.Use [LEFT] or [RIGHT] button to select a mode then
press [SET].
Menu Operation
•
ATW (Auto-Tracing White Balance): Use [LEFT]
or [RIGHT] button to select the ATW then press
[SET] button.
You can select the USER MODE.
(STANDARD - VIVID - WARM - COOL)
--
>>
>>
•
AWC/PUSH: If you select the AWC /PUSH
mode, you will be able to set up the White
Balance automatically using [SET] button.
•
MANUAL: You can set the white balance options
manually.
>>
INDOOR: The color temperature range
for the proper white balance is approximately 3 200 K.
-OUTDOOR: The color temperature range
for the proper white balance is approximately 5 100 K.
RED: Obtains the optimum amount of red
gain.
BLUE: Obtains the optimum amount of blue
gain.
COLOR TEMP: Use [LEFT] or [RIGHT] button
to select a function.
29
Menu Operation
3D-DNR Setting
Day/Night Setting
1.
1.
Select [3D-DNR] option.
If pictures are not clear due to brightness, this option
would reduce the noise of picture.
2.Use [LEFT] or [RIGHT] button to select a option.
LOW
MIDDLE
HIGH)
(OFF
Notes:
•
If you set the AGC to [OFF] on the [EXPOSURE] menu,
the [3D-DNR] function is not available and [---] mark
is displayed.
•
When you use this function, the afterimage may occur.
30
Select [DAY/NIGHT] option.
2.Use [LEFT] or [RIGHT] button to select mode for day/
night function.
•
AUTO: You will be able to change the Day/Night
mode automatically.
Note:
If you set the AGC to [OFF] or the SHUTTER is set
to one of the SHUTTER options except AUTO on
the [EXPOSURE] menu, the AUTO mode of the
DAY/NIGHT function is not available and [---]
mark is displayed.
Menu Operation
•
LEVEL: Use [LEFT] or [RIGHT] button to
select a level.
MIDDLE HIGH)
(LOW
>> DWELL TIME: Use [LEFT] or [RIGHT] button
to select a dwell time.
(5, 10, 15, 30 or 60 SEC)
DAY: Color mode enabled.
•
NIGHT: Black-and-white mode enabled.
>>
Privacy Setting
This function is aiming at the protection of personal privacy, selecting a screen part black not to be displayed in
the screen. Up to 8 zones can be registered.
1.
Select [PRIVACY] option.
2.Use [LEFT] or [RIGHT] button to select a [ON] and
press [SET]. The PRIVACY SETUP menu appears.
3.Use [LEFT] or [RIGHT] button to select a mask (AREA1
to AREA8) on the [MASK NUMBER].
4.Use [LEFT] or [RIGHT] button to set up the ON or OFF
on the DISPLAY SET option.
31
Menu Operation
5.Use [LEFT] or [RIGHT] button to set up the GRAY,
WHITE or BLACK on the COLOR SET option.
Special Menu Settings
6.Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
This menu lets you adjust and set up LANGUAGE, COLOR
EFFECT, SHARPNESS, STABILIZER, D-ZOOM, D-EFFECT,
MOTION DET, FACTORY RESET function by yourself in the
SPECIAL menu.
•
HEIGHT: Enlarge or decrease the vertical size of
the mask.
•
WIDTH: Enlarge or decrease the horizontal size of
the mask.
•
MOVE Y: Moves vertical position of the mask.
•
MOVE X: Moves horizontal position of the mask.
Note:
The parts with the registered mask numbers from AREA1 to
AREA4 have the same color. (So do the parts with the numbers from AREA5 to AREA8). If you change the mask color,
the registered mask color will be changed automatically
with the same color for each of group (AREA1 to AREA4,
AREA5 to AREA8).
32
1.
Select [SPECIAL] option.
2.Press [SET] button and the SPECIAL menu appears.
Menu Operation
LANGUAGE Setting
Setting the COLOR EFFECT
Select the viewer language for the camera setup menu and
OSD information display.
You can switch the displayed picture to gray scale or color.
1.
Select [LANGUAGE] option on the [SPECIAL] screen.
2.Press [LEFT] or [RIGHT] button to select a language.
1.
Select [COLOR EFFECT] option on the [SPECIAL] menu.
2.Use [LEFT] or [RIGHT] button to change a color effect.
•
ON: To display the picture with color.
•
OFF: To display the picture with grayscale.
33
Menu Operation
Setting the SHARPNESS effect
STABILIZER setting
The degree to which the boundary of the two portions is
clearly distinguished.
1.
Select [SHARPNESS] option on the [SPECIAL] menu.
2.Use [LEFT] or [RIGHT] button to change a adjust
the option. If you set the sharpness value to higher,
the image outline becomes sharp. If you set to lower
value, the image outline becomes dim.
34
The image stabilizer function minimizes the appearance of
shaky images caused by low-frequency vibration.
This function is useful for outdoor surveillance.
Select [STABILIZER] option and set to ON or OFF.
Note:
If you set the [STABILIZER] to ON, the Digital zoom is set to
[x1.1] automatically.
Menu Operation
Setting the D-ZOOM (Digital Zoom ) level
•
You can select the digital zoom level.
TILT: Use [LEFT] or [RIGHT] button to move the
screen. (up or down)
Setting the D-EFFECT (Digital effect)
You can select the digital effect.
1.
Select [D-ZOOM] option on the [SPECIAL] menu.
2.Use [LEFT] or [RIGHT] button to select a [ON] then
press [SET] the DIGITAL ZOOM menu appears. When
you set to ON, the displayed image can be shaking.
3.Use [UP] or [DOWN] to select a option then use
[LEFT] or [RIGHT] button to select a level.
•
•
ZOOM: Use [LEFT] or [RIGHT] button to enlarge
the screen.
PAN: Use [LEFT] or [RIGHT] button to move the
screen. (left or right)
1.
Select [D-EFFECT] option on the [SPECIAL] menu.
2.Use [LEFT] or [RIGHT] button to select a digital effect.
•
V-FLIP: Flip the picture vertically.
•
MIRROR: Turn on the mirror effect.
•
ROTATE: Rotate the picture. (180°)
•
OFF: Turn off the digital effect.
35
Menu Operation
Motion Detection Setting
[LEFT] or [RIGHT] button to adjust the option.
The motion detection detects the moving objects in the
scene by monitoring changes in brightness level. You can
select the level of sensitivity for motion detection to 4 zone.
•
HEIGHT: Enlarge or decrease the vertical size of
the mask.
•
WIDTH: Enlarge or decrease the horizontal size of
the mask.
•
MOVE Y: Moves vertical position of the mask.
•
MOVE X: Moves horizontal position of the mask.
6.
1.
Select [MOTION DET] option.
2.Use [LEFT] or [RIGHT] button to select a [ON] and
press [SET].
The MOTION DETECTION menu appears.
3.Use [LEFT] or [RIGHT] button to select a zone number
(AREA1 to AREA4) on the [ZONE NUMBER].
4.Use [LEFT] or [RIGHT] button to set up the ON or OFF
on the ZONE STATE.
5.Use [UP] or [DOWN] to select an option then use
36
Use [SENSITIVITY] option to obtain the optimum
detection level.
Menu Operation
Factory Reset Setting
•
FACTORY RESET: To reset the camera setting to
factory setting, select [FACTORY RESET] option.
37
Specification
Item
Signal System
Total/Effective Pixels
Image Device
DSP
Lens
Digital Zoom
Sync. System
Scanning Frequency (H/V)
Horizontal Resolution
S/N Ratio
Minimum
Illumination
(30 IRE, F1.2)
Color mode
B/W mode
Control Method
Video Output Signal
Day & Night
BACKLIGHT
38
L6213-BP
L6213-BN
L6213-DN
PAL
NTSC
470 000 Pixels / 440 000 Pixels
410 000 Pixels / 380 000 Pixels
6 mm Super HAD II CCD
XDI-S2
2.8 mm to 11 mm Vari-focal lens (F1.2)
X8
Internal
15.625 kHz / 50 Hz
15.734 kHz / 59.94 Hz
620 TV Lines
52 dB
0.06 lx (Sens-up OFF)
0.0001 lx (Sens-up Auto)
0.006 lx (Sens-up OFF)
0.000 001 lx (Sens-up x128)
Inner Key Button
1 Vp-p Composite (75 Ω)
Day / Night / Auto
OFF / BLC / HSBLC
Specification
Item
DNR
Auto Gain Control
Electronic Shutter Speed
Electronic Sensitivity
White Balance
Motion Detection
Privacy Zone Masking
Stabilizer( EIS)
User Color Mode
Power Source
Power Consumption
Operation Temp.
Storage Temp.
Operation Humidity
Storage Humidity
Weight
Dimension (Ø x H)
L6213-BP
L6213-BN
L6213-DN
3D-DNR (Off/Low/Middle/High)
Off / Low / Middle / High
1/50 to 1/90 000
1/60 to 1/90 000
OFF/Auto
ATW / AWC /PUSH / Manual
4 Zones
8 Masks
On / Off
STANDARD/COOL/WARM/VIVID
DC 12 V / AC 24 V
DC 12 V
2.8 W
2.2 W
-10 ºC to 50 ºC
-20 ºC to 60 ºC
0 % RH to 80 % RH
0 % RH to 85 % RH
640 g
Ø 140 x 91.7 mm
39
AB28
Download PDF

advertising