LG | L5213R-BP | LG L5213R-BP Owner’s Manual

OWNER’S MANUAL
Color Video Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODELS
L5213R-BN
L5213R-BP
L5213R-DN
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to alert
the user to the presence of uninsulated dangerous voltage within the product’s enclosure that
may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
Regulatory Notices For U.S.A
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
• A suitable conduit entries, knock-outs or glands shall be
provided in the cable entries of this product in the end
user.
• Caution: Danger of explosion if battery is incorrectly re
placed. Replaced only with the same or equivalent type
recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
• Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall be
provided with brushings.
Warning: Do not install this equipment in a confined space
such as a bookcase or similar unit.
Caution: This installation should be made by a qualified
service person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Caution: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
Warning: Wiring methods shall be in accordance with the
National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic
environment this product may cause radio interference in
which case the user may be required to take adequate measures.
Warning: To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it means the
product is covered by the European Directive
2002/96/EC.
2. All electrical and electronic products
should be disposed of separately from the
municipal waste stream via designated
collection facilities appointed by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and
human health.
4. For more detailed information about
disposal of your old appliance, please contact your city office, waste disposal service or
the shop where you purchased the product.
LG Electronics hereby declares that this/
these product(s) is/are in compliance with
the essential
requirements and other relevant provisions
of Directive 2004/108/EC, 2006/95/EC, and
2009/125/EC.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : +31-(0)36-547-8888)
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accord
ance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally,
or has been dropped.
Cautions for Safe Operation
Power Supply
•
L5213R-BP/L5213R-BN:
This camera must always be operated a AC 24 V or DC 12 V
Certified/Listed, class 2 power supply only.
Operating and storage location
L5213R-DN:
This camera must always be operated a DC 12
Avoid viewing a very bright object (such as light fittings) during an extended period. Avoid operating or storing the unit in
the following locations.
Handling of the unit
•
Be careful not to spill water or other liquids on the unit. Be
cautions not to get combustible or metallic material inside
the body. If used with foreign matter inside, the camera is
liable to fail or to get cause of fire or electric shock.
•
Remove dust or dirt on the surface of the lens with a
blower.
•
Use a dry soft cloth to clean the body. If it is very dirty,
use a cloth dampened with a small quantity of neutral
detergent then wipe dry.
•
•
•
•
Avoid the use of volatile solvents such as thinners,
alcohol, benzene and insecticides. They may damage the
surface finish and/or impair the operation of the camera.
Extremely hot or cold places (operating temperature
-10 °C to 50 °C, however, we recommend that the unit be
used within a temperature range of 0 °C to 45 °C)
Damp or dust place
Places exposed to rain
Places subject to strong vibration
Close to generators of powerful electromagnetic radia
tion such as radio or TV transmitters.
Contents
Features................................................................................. 8
Part Names and Functions................................................... 9
Connections........................................................................ 10
Basic connection............................................................................ 10
Installation ......................................................................... 11
Installing the camera on a ceiling or wall..................................11
Adjustment.............................................................................................13
Menu Operation..................................................................15
OSD Menu Overview......................................................................16
General Operation..........................................................................18
Setting the USER TITLE ..................................................................18
Exposure Settings...........................................................................19
BACKLIGHT setting..............................................................19
BRIGHTNESS setting........................................................... 20
AGC (Automatic Gain Control) setting.......................... 21
SHUTTER (Shutter Speed) setting.................................. 21
SENS-UP setting.................................................................. 22
White Balance settings.................................................................. 22
3D-DNR Setting.............................................................................. 24
Day/Night Setting.......................................................................... 24
Privacy Setting................................................................................ 25
Special Menu Settings............................................................... 26
LANGUAGE Setting............................................................ 27
Setting the COLOR EFFECT............................................... 27
Setting the SHARPNESS effect......................................... 28
STABILIZER setting.............................................................. 28
Setting the D-ZOOM (Digital Zoom ) leve.................... 29
Setting the D-EFFECT (Digital effect.............................. 29
Motion Detection Setting........................................................ 30
Factory Reset Setting................................................................. 31
Specification....................................................................... 32
Features
This Color Video Camera is designed for installation in an
indoor video surveillance system.
This manual contains instructions on how to install and manage the Color Video Camera in your video surveillance system.
Should you require any technical assistance, please contact
authorized service center.
• High resolution and high sensitivity with a 6 mm CCD.
• Day & Night function.
• BLC covers various light conditions.
• Excellent signal-to-noise ratio of 52 dB.
• Power Supply : Automatically switch between
DC 12 V and AC 24 V
Accessories
DOME CAMERA
VIDEO OUTPUT
TEST CABLE
SCREW
TEMPLATE
Part Names and Functions
- Dome Cover
- Photo Cell
- LED(30ea)
- Video Output Jack
- Power Input Jack
Supplies AC 24 V or DC 12 V from an external power source.
- LED Cover
- OSD Setup Switch
- Service Video Connector
Use this jack for checking the picture with portable monitor when
install the camera.
Connections
Basic connection
The peripheral devices (DVR, monitor, etc.), AC/DC adapter and cables
are not supplied.
DUAL(DC12V/AC24V)
DC12V
DC12V /AC24V POWER SUPPLY
DC12V/AC24V
BNC FEMALE
10
DC12V POWER SUPPLY
DC12V
VIDEO IN
BNC FEMALE
VIDEO IN
Installation
Installing the camera on a ceiling or wall
. Affix the mounting template(supplied) to the mounting surface.
. Secure the camera mounting bracket to the position where the
camera should be mounted with the supplied screws.
Template
Tapping Type
ø2x7mmx1ea
(Supplied)
Tapping Type ø4x20mmx3ea
(Supplied)
11
Installation
. Adjust the camera lens to face the area to be monitored and fix the
main body and the dome cover by aligning the grooves and rotating
the body clockwise.
12
Installation
Adjustment
Having a better view , adjust the camera
Service Video connector
Connect a portable monitor to the video jack.
• Rotate angle : 360˚
• Panning angle : 360˚
• Tilting angle : 90˚
(Viewable operation tilt angle 60˚~65˚)
ROTATE 360˚
PAN 360˚
Service Monitor
TILT 90˚
CAUTION : panning the bracket in excess of 3 rotations in one
direction may cause damage to the cable.
13
Installation
Follow the instruction provided below
to make any lens adjustments
• Loosen the Zoom & Focus screws.
• Using the screw, move it LEFT or RIGHT to the desired position.
• Once the desired adjustments have been made, tighten the screw to
lock in place.
• Adjust the Field of View by moving the screw towards the LEFT(Tele) to
zoom in, or towards the RIGHT(Wide) to zoom out.
• Adjust the Focus the same way as described above after the desired
zoom position is established.
Focus: Far ← → Near
Zoom: Tele ← → Wide
FAR
TELE
14
NEAR
WIDE
Menu Operation
This camera utilizes an on-screen user MENU.
To set items on the menu, use the following switch.
• UP
Used to move upper direction on the menu screen. Use
this button to select an item or adjust the parameters.
• DOWN
Used to move lower direction on the menu screen. Use this
button to select an item or adjust the parameters.
• RIGHT
Moves the cursor to the right. Used to increment the value
selected in the menu. The parameter changes each time
this button is pressed.
• LEFT
■: Set
Moves the cursor to the left. Used to decrement the value
selected in the menu. The parameter changes each time
this button is pressed.
• SE T
Executes selections and displays a submenu for an item
with the ↵mark.
15
Menu Operation
OSD Menu Overview
Main Menu
The following table shows the list of menu items and options.
You can adapt the camera to your requirements by setting up the
respective items in these menus.
ATW
USER TITLE
Main Menu
USER TITLE
EXPOSURE
16
Sub Menu
OFF
ON
ALC/ ELC
Contents
BACKLIGHT
OFF/BLC/HSBLC
BRIGHTNESS
0 to 100
OFF/LOW/MIDAGC
DLE/HIGH
AUTO/OFF/
SHUTTER
A.FLK/1/60, ..., 1/90
000/x512, ..., x2
OFF
SENS-UP
AUTO
Sub Menu
Contents
STANDARD
VIVID
WARM
COOL
USER MODE
AWC → PUSH
INDOOR,
OUTDOOR
-100 to 100
-100 to 100
COLOR TEMP
MANUAL
3D-DNR
RED
BLUE
OFF
LOW
MIDDLE
HIGH
AUTO
LOW/ MIDDLE/
HIGH
5, 10, 15, 30, 60 SEC
LEVEL
DWELL TIME
DAY/NIGHT
DAY
NIGHT
-
Menu Operation
Main Menu
Sub Menu
OFF
Contents
AREA1 to AREA8
ON/OFF
GRAY/ WHITE/
COLOR SET
BLACK
HEIGHT
4 to 100
WIDTH
4 to 100
MOVE Y
2 to 98
MOVE X
2 to 98
Main Menu
PRIVACY
ON
Sub Menu
LANGUAGE
MASK NUMBER
DISPLAY SET
COLOR EFFECT
SHARPNESS
STABILIZER
D-ZOOM
D-EFFECT
SPECIAL
MOTION DET
EXIT
FACTORY RESET
-
Contents
ENG/CHN/KOR/JAP/FRE/ITA/SPA/POR/
DUT/GER/POL/RUS/TUR/ARA/HEB
OFF/ ON
0 to 68
OFF/ ON
OFF
ZOOM
ON
PAN
TULT
OFF/ V-FLIP/ MIRROR/ ROTATE
OFF
ZONE
AREA1 to AREA4
NUMBER
ON
ZONE STATE
OFF/ON
HEIGHT
12 to 100
WIDTH
16 to 100
MOVE Y
6 to 94
MOVE X
SENSITIVITY
-
8 to 92
0 to 100
17
Menu Operation
General Operation
Setting the USER TITLE
1. Press [SET] button.
The setup menu screen appears on the monitor.
You can use the camera identification to assign a number and character
to the camera (0 to 9, A to Z, a to z).
The USER TITLE is displayed on the upper left of the screen. To disappear
the user title, select [OFF].
1. Select [USER TITLE] option.
2. Use [LEFT] or [RIGHT] button to select a [ON] then press [SET].
The USER TITLE menu appears.
2. Use [UP] or [DOWN] button to select an option then
press [SET] button.
Submenu appears on the monitor.
3. Use [UP] or [DOWN] button to select a submenu option.
4. Use [LEFT] or [RIGHT] button to select a value.
5. Select [EXIT] option then press [SET] to exit the setup menu. In the
submenu, use [UP] or [DOWN] button to select the [RETURN] then
press [SET] to return to the previous setup menu.
• RETURN: Return to the previous.
18
3. Use [UP], [DOWN], [LEFT] or [RIGHT] button to select
a character or number then press [SET] button.
• CLR: Clear all entered characters and numbers.
• POS: Move the USER TITLE position on the screen
using the arrow buttons.
Menu Operation
• END: Confirm your selection or exit the setting
• (Blank): Inserts a space at the cursor position.
• ←/→ : Moves cursor to left or right.
Exposure Settings
You can set the exposure options using the EXPOSURE menu.
1. Select [EXPOSURE] option on the [CAMERA SETTING] menu.
2. Use [LEFT] or [RIGHT] button to select a mode (AL↔ ELC).
3. Press [SET] button and the EXPOSURE menu appears.
BACKLIGHT setting
Use BACKLIGHT option to view the object clearly in backlight
conditions.
1. Select [BACKLIGHT] option.
19
Menu Operation
2. Use [LEFT] or [RIGHT] button to select a mode then press [SET].
• BLC: Camera's backlight compensation feature
helps alleviate issues of visibility in high contrast areas.
Set the BLC limit.
> BLC LIMIT: LOW ↔ MIDDLE ↔ HIGH
• OFF: Not used.
BACKLIGHT setting
You can increase the brightness of the darkened video. If you set the
brightness to lower value, the image is darkened.
If you set the brightness to higher value, the image gets bright.
• HSBLC: Use for masking brightness of the specific area to view the
subject more clearly. The HSBLC mode is automatically activated
only in low luminance scene.
> AREA SETTING: Use [LEFT] or [RIGHT] button
to select a area then use [UP] or [DOWN] button to select a ON
or OFF. Press [SET] to exit the Area setting menu.
> GRAY SCALE: Use [LEFT] or [RIGHT] button to select a gray
scale. (GRAY ↔ D.GRAY ↔ BLACK).
> USER SCALE: Use [LEFT] or [RIGHT] button to select a bright
level.(5 level)
> MASK: Use [LEFT] or [RIGHT] button to select [ON] or [OFF].
If you set the MASK to ON, the mask function
is activate only when the HSBLC is automatically
activated in low luminance scene.
20
1. Select [BRIGHTNESS] option.
2. Use [LEFT] or [RIGHT] button to set the bright level.
Menu Operation
AGC (Automatic Gain Control) setting
SHUTTER (Shutter Speed) setting
1. Select [AGC] option.
2. Use [LEFT] or [RIGHT] button to select a mode.
(OFF ↔ LOW ↔ MIDDLE ↔ HIGH)
1. Select [SHUTTER] option.
2. Use [LEFT] or [RIGHT] button to set shutter speed.
(AUTO ↔ OFF ↔ A.FLK ↔ 1/160, ..., 1/90 000 ↔ x512, ..., x2)
If the images are too dark, change the maximum [AGC]
value to make the images brighter.
Select the desired shutter speed for camera exposure. You can change
the shutter speed to higher speed to capture fast-moving subjects,
though the image becomes darker.
21
Menu Operation
SENS-UP setting
If pictures are not clear due to darkness, this SENS-UP
operation would increase the sensitivity of picture.
Note:
If you set to one of the SHUTTER options except AUTO on the [SHUTTER]
menu or [AGC] to [OFF], the [SENS-UP] setting
is not available and [---] mark is displayed.
White Balance settings
Select the method by which the camera shifts its output colors to
compensate for the color of a light source.
1. Use [UP] or [DOWN] button to select [SENS-UP] option.
2. Use [LEFT] or [RIGHT] button to select mode.
• AUTO: Adjust the sensitivity of the picture auto matically.
> SENS-UP LIMIT: Use [LEFT] or [RIGHT] button to set
the SENS-UP limit.
• OFF: Not used.
22
1. Select [WHITE BAL] option.
2. Use [LEFT] or [RIGHT] button to select a mode then press [SET].
Menu Operation
• ATW (Auto-Tracing White Balance): Use [LEFT] or [RIGHT] button
to select the ATW then press [SET] button.
You can select the USER MODE.
(STANDARD - VIVID - WARM - COOL)
- INDOOR: The color temperature range for the proper
white balance is approximately3 200 K.
- OUTDOOR: The color temperature range for the proper
white balance is approximately 5 100 K.
> RED: Obtains the optimum amount of red gain.
> BLUE: Obtains the optimum amount of blue gain.
• AWC → PUSH: If you select the AWC → PUSH mode, you will be able
to set up the White Balance automatically using [SET] button.
• MANUAL: You can set the white balance options manually.
23
Menu Operation
3D-DNR Setting
Day/Night Setting
1. Select [3D-DNR] option.
If pictures are not clear due to brightness, this option would reduce
the noise of picture.
1. Select [DAY/NIGHT] option.
2. Use [LEFT] or [RIGHT] button to select mode for day/night function.
• AUTO: You will be able to change the Day/Night mode automatically.
2. Use [LEFT] or [RIGHT] button to select a option.
(OFF ↔ LOW ↔ MIDDLE ↔ HIGH)
Notes:
• If you set the AGC to [OFF] on the [EXPOSURE] menu, • the [3D-DNR]
function is not available and [---] mark is displayed.
• When you use this function, the afterimage may occ
24
Note:
If you set the AGC to [OFF] or the SHUTTER is set to one of the
SHUTTER options except AUTO on the [EXPOSURE] menu, the AUTO
mode of the DAY/NIGHT function is not available and [---] mark is
displayed.
Menu Operation
> LEVEL: Use [LEFT] or [RIGHT] button to select a level.
(LOW ↔ MIDDLE ↔ HIGH)
> DWELL TIME: Use [LEFT] or [RIGHT] button to select a dwell time.
(5, 10, 15, 30 or 60 SEC)
Privacy Setting
This function is aiming at the protection of personal privacy,
selecting a screen part black not to be displayed in the screen. Up to 8
zones can be registered.
• DAY: Color mode enabled.
• NIGHT: Black-and-white mode enabled.
1. Select [PRIVACY] option.
2. Use [LEFT] or [RIGHT] button to select a [ON] and press [SET].
The PRIVACY SETUP menu appears.
3. Use [LEFT] or [RIGHT] button to select a mask (AREA1 to AREA8)
on the [MASK NUMBER].
4. Use [LEFT] or [RIGHT] button to set up the ON or OFF on the
DISPLAY SET option.
25
Menu Operation
5. Use [LEFT] or [RIGHT] button to set up the GRAY,
WHITE or BLACK on the COLOR SET option.
6. Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
Special Menu Settings
This menu lets you adjust and set up LANGUAGE, COLOR EFFECT,
SHARPNESS, STABILIZER, D-ZOOM, D-EFFECT, MOTION DET, FACTORY
RESET function by yourself in the SPECIAL menu.
• HEIGHT: Enlarge or decrease the vertical size of the mask.
• WIDTH: Enlarge or decrease the horizontal size of the mask.
• MOVE Y: Moves vertical position of the mask.
• MOVE X: Moves horizontal position of the mask.
Note:
The parts with the registered mask numbers from AREA1 to AREA4
have the same color. (So do the parts with the numbers
from AREA5 to AREA8). If you change the mask color, the registered
mask color will be changed automatically with the same color for
each of group (AREA1 to AREA4, AREA5 to AREA8).
26
1. Select [SPECIAL] option.
2. Press [SET] button and the SPECIAL menu appears.
Menu Operation
LANGUAGE Setting
Setting the COLOR EFFECT
1. Select [LANGUAGE] option on the [SPECIAL] screen.
2. Press [LEFT] or [RIGHT] button to select a language.
1. Select [COLOR EFFECT] option on the [SPECIAL] menu.
2. Use [LEFT] or [RIGHT] button to change a color effect.
• ON: To display the picture with color.
• OFF: To display the picture with grayscale.
Select the viewer language for the camera setup menu and
OSD information display.
You can switch the displayed picture to gray scale or color.
27
Menu Operation
Setting the SHARPNESS effect
STABILIZER setting
1. Select [SHARPNESS] option on the [SPECIAL] menu.
2. Use [LEFT] or [RIGHT] button to change a adjust the option.
If you set the sharpness value to higher, the image outline becomes
sharp. If you set to lower value, the image outline becomes dim.
The image stabilizer function minimizes the appearance of shaky images caused by low-frequency vibration.
This function is useful for outdoor surveillance.
Select [STABILIZER] option and set to ON or OFF.
The degree to which the boundary of the two portions is clearly
distinguished.
Note:
If you set the [STABILIZER] to ON, the Digital zoom is set to [x1.1]
automatically.
28
Menu Operation
Setting the D-ZOOM (Digital Zoom ) level
Setting the D-EFFECT (Digital effect)
You can select the digital zoom level.
You can select the digital effect.
1. Select [D-ZOOM] option on the [SPECIAL] menu.
2. Use [LEFT] or [RIGHT] button to select a [ON] then
press [SET] the DIGITAL ZOOM menu appears. When you set to ON,
the displayed image can be shaking.
3. Use [UP] or [DOWN] to select a option then use
[LEFT] or [RIGHT] button to select a level.
1. Select [D-EFFECT] option on the [SPECIAL] menu.
2. Use [LEFT] or [RIGHT] button to select a digital effect.
• V-FLIP: Flip the picture vertically.
• MIRROR: Turn on the mirror effect.
• ROTATE: Rotate the picture. (180°)
• OFF: Turn off the digital effect.
• ZOOM: Use [LEFT] or [RIGHT] button to enlarge the screen.
• PAN: Use [LEFT] or [RIGHT] button to move the
screen. (left or right)
• TILT: Use [LEFT] or [RIGHT] button to move the
screen. (up or down)
29
Menu Operation
Motion Detection Setting
The motion detection detects the moving objects in the scene by monitoring changes in brightness level. You can select the level of sensitivity
for motion detection to 4 zone.
5. Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
• HEIGHT: Enlarge or decrease the vertical size of the mask.
• WIDTH: Enlarge or decrease the horizontal size of the mask.
• MOVE Y: Moves vertical position of the mask.
• MOVE X: Moves horizontal position of the mask.
6. Use [SENSITIVITY] option to obtain the optimum detection level.
1. Select [MOTION DET] option.
2. Use [LEFT] or [RIGHT] button to select a
[ON] and press [SET].
The MOTION DETECTION menu appears.
3. Use [LEFT] or [RIGHT] button to select a zone number
(AREA1 to AREA4) on the [ZONE NUMBER].
4. Use [LEFT] or [RIGHT] button to set up the ON or OFF
on the ZONE STATE.
30
Menu Operation
Factory Reset Setting
• FACTORY RESET: To reset the camera setting to
factory setting, select [FACTORY RESET] option.
31
Specification
Model
L5213R–BP
Signal System
PAL
NTSC
Total Pixels No. /
Effective Pixels No.
470K / 440K
410K / 380K
Image Device
1/3" CCD (ICX638/639BK)
DSP
XDI-S2
Lens
2.8~11mm Vari-focal lens
Digital Zoom
X8
Sync. System
Internal
Scanning Frequency (H/V)
Horizontal Resolution
32
L5213R-BN/DN
15.625 KHz / 50 Hz
15.734 KHz / 59.94 Hz
620 TV Lines
S/N Ratio
52dB
Minimum Illumination
(30 IRE)
0 Lux (IR LED On)
IR LED Distance : 25 m
Control Method
Inner Key button
Video Output Signal
1Vp-p Composite (75Ω)
Day & Night
ICR Day / Night / Auto
WDR(BLC)
OFF / BLC / HSBLC
DNR
3D-DNR (Off/Low/Middle/High)
Auto Gain Control
Off / Low / Middle / High
Specification
Electronic Shutter Speed
1/50 ~1/90,000
1/60 ~1/90,000
Electronic Sensitivity
OFF/Auto ( x2, x3, x4,…..x 128 )
White Balance
Auto / ATW / One Push / Manual
(1,700ºk ~ 11,000ºk)
Motion Detection
4 Zones
Privacy Zone Masking
8 Masks
Stabilizer(EIS)
On / Off
User Color Mode
Standard / Cool / Warm / Vivid
Multi OSD Language
Power
Consumption
Dual
DC12V
15 Languages
LED ON
DC12V ±10% Max. 470mA / AC24V ±10% Max. 450mA / 6.0W
LED OFF
DC12V ±10% Max. 210mA / AC24V ±10% Max. 235mA / 3.0W
LED ON
-
LED OFF
-
DC12V ±10% Max. 390mA
DC12V ±10% Max. 160mA
Operation Temp./Humidity
-10ºC ~ 50ºC ( 0%RH ~ 80%RH )
Storage Temp./Humidity
-20ºC ~ 60ºC ( 0%RH ~ 85%RH )
Weight
342g
Dimension
96.9(H) x Ø135
Accessory
TEMPLATE
33
Download PDF