OWNER'S MANUAL
IR Dome Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
LCD5300R-BN
LCD5300R-BP
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle is
intended to alert the user to the presence
of uninsulated dangerous voltage within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
2
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the
modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is
made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment
is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference
to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
•
A suitable conduit entries, knock-outs or glands shall
be provided in the cable entries of this product in the
end user.
•
•
Caution: Danger of explosion if battery is incorrectly
replaced. Replaced only with the same or equivalent
type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s
instructions.
Caution: This installation should be made by a qualified
service person and should conform to all local codes.
Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall be
provided with brushings.
Caution: The apparatus shall not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
Warning: Do not install this equipment in a confined space
such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the
National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
Note:
Please make sure the product is installed appropriate
places where secured from flood, such as under the
eaves, to operate properly. This product is certified as IP66
standard. However, if there is any flood concerns, it is highly
recommended to use an outdoor Housing When you install
the camera inside an outdoor Housing, please use one of
the following methods:
1. Remove the front glass of Housing before installing the
camera.
2.
To keep the front glass of Housing, remove the front
cover, and then put the camera close to the front glass.
Warning: To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
3
LG Electronics hereby declares
that this/these product(s) is/are
in compliance with the essential
requirements and other relevant
provisions of Directive 2004/108/EC
and 2011/65/EU.
European Standards Centre:
Krijgsman 1, 1186 DM Amstelveen The
Netherlands
Disposal of your old appliance
1.
2.
3.
4
This crossed-out wheeled bin symbol
indicates that waste electrical and
electronic products (WEEE) should
be disposed of separately from the
municipal waste stream.
Old electrical products can contain hazardous
substances so correct disposal of your old appliance
will help prevent potential negative consequences
for the environment and human health. Your old
appliance may contain reusable parts that could be
used to repair other products, and other valuable
materials that can be recycled to conserve limited
resources.
You can take your appliance either to the shop
where you purchased the product, or contact your
local government waste office for details of your
nearest authorised WEEE collection point. For the
most up to date information for your country please
see www.lg.com/global/recycling
t
Please note that this is NOT a Customer Service
contact point. For Customer Service Information, see
Warranty Card or contact the dealer that you purchased this product.
Important Safety Instructions
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
5
Cautions for Safe Operation
Power Supply
Operating and storage location
This camera must always be operated DC 12 V or AC 24
V.Certified/Listed Adaptor which comply with LPS.
Avoid viewing a very bright object (such as light fittings)
during an extended period. Avoid operating or storing the
unit in the following locations.
Handling of the unit
Be careful not to spill water or other liquids on the unit. Be
cautions not to get combustible or metallic material inside
the body. If used with foreign matter inside, the camera is
liable to fail or to get cause of fire or electric shock.
t
Remove dust or dirt on the surface of the lens with a
blower.
t
Use a dry soft cloth to clean the body. If it is very dirty,
use a cloth dampened with a small quantity of neutral
detergent then wipe dry.
t
Avoid the use of volatile solvents such as thinners,
alcohol, benzene and insecticides. They may damage
the surface finish and/or impair the operation of the
camera.
6
t
Extremely hot or cold places (operating temperature
-10 °C to 50 °C, however, we recommend that the unit
be used within a temperature range of 0 °C to 45 °C)
t
Damp or dust place
t
Places exposed to rain
t
Places subject to strong vibration
t
Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
Contents
Features ............................................................................. 8
Privacy Mask Setting .............................................................29
Accessories.................................................................................. 8
Special Menu Settings ..........................................................31
Part Names and Functions .................................................... 9
SYSTEM Setting .......................................................................35
Connections .................................................................... 11
Specification ................................................................... 36
Basic connection .....................................................................11
Installation ...................................................................... 12
Mounting the Camera...........................................................12
Image Adjustment .................................................................14
Menu Operation.............................................................. 18
OSD Menu control buttons .................................................18
OSD Menu Overview .............................................................19
General Operation..................................................................21
Exposure Settings ...................................................................22
White Balance settings .........................................................25
Day/Night Setting ..................................................................26
SmartIR Setting .......................................................................27
Motion Detection Setting....................................................28
3D-DNR Setting .......................................................................29
7
Features
This IR Bullet Camera is designed for installation in a video
surveillance system.
Accessories
This manual contains instructions on how to install and
manage the IR Bullet Camera in your video surveillance
system.
Should you require any technical assistance, please contact
authorized service center.
t
High resolution and high sensitivity with a 6 mm (1/3
Type) CCD.
t
Day & Night function.
t
HSBLC/BLC covers various light conditions.
FRONT
MEZ62687703
SELFTAPPING SCREW
4 Place
PRODUCT CENTER POSITION
Installation sticker
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
Fixing screws
8
n100 Cutting Line
Part Names and Functions
a Dome Cover
b IR LED
c IR Sensor
a
d Focus lock lever
Fixes the focus position after adjusting.
e Zoom lock lever
Fixes the zoom position after adjusting.
f Rotate adjuster
b
c
d
e
f
Adjusts the rotate angle to obtain a level image.
g Lock button
You can lock the camera mounting bracket by using
the lock button.
g
9
Part Names and Functions
h Pan adjuster
Adjusts the pan position.
h
i
j
k
l
i Video Out connector
Use this jack for checking the picture with portable
monitor when install the camera.
j Setup menu control buttons
k Power input connector
Supplies AC 24 V or DC 12 V from an external power
source.
l Video output connector (BNC type)
m Camera mounting bracket
m
10
This bracket is supplied for ceiling installation.
Connections
Basic connection
The peripheral devices (DVR, monitor, etc.), AC/DC adapter
and cables are not supplied.
1.
2.
Connect a external power source to the power input
jack of the camera. (recommended power adapter is
AC 24 V/0.5 A, DC 12 V/0.5 A or above)
Make the video signal connection between the
camera and the monitor or DVR.
11
Installation
2.
Mounting the Camera
Pass the connection cable through the inner side of
the ceiling.
Surface mount
PR
OD
UC
T
CE
NT
E
R
PO
SIT
IO
N
SE
LF
70
3
FR
ON
87 T
Cu
tt
ing
n10
0
W
T
ON
FR
SE
LF
TA
PP
4 ING
Pl SC
ac
e RE
ME
Z6
26
87
703
SI
TI
ON
PO
ER
NT
CE
T
UC
OD
PR
CA
CA BLE
BL HO
E LE
HO
LE (L
CV
(L 53
CD 00
53 )
00
)
ME
Z6
26
Lin
e
Lin
ing
tt
Cu
0
n10
W
703
FR
O
26 NT
87
TA
PP
4 ING
Pl SC
ac
e RE
Z6
LF
SE
ME
ON
TI
SI
PO
ER
NT
CE
T
UC
OD
CA
CA BLE
BL HO
E LE
HO
LE (L
CV
(L 53
CD 00
53 )
00
)
PR
12
CA
CA BLE
BL H
E OL
HO E
LE (L
C
(L V5
CD 300
53 )
00
)
Use the installation guide template to check the
mounting location. Face the front of the label toward
the area of interest. Using the template as a guide,
make a hole through the ceiling.
e
1.
TA
PP
4 ING
Pl S
ac C
e RE
W
n10
0
Cu
tt
ing
Lin
e
Follow the instructions below to surface mount the camera
with supplied camera mounting bracket.
Installation
4.
Connect the cables to the cable jacks of the camera
body.
70
3
FR
O
26 NT
87
LF
Z6
T
UC
OD
PR
CA BLE
BL H
E OL
HO E
LE (L
C
(L V5
CD 300
53 )
00
)
CE
NT
ER
PO
SIT
IO
N
SE
ME
TA
PP
4 ING
Pl S
ac C
e RE
W
n10
0
Cu
tt
ing
Lin
e
Install the camera mounting bracket to the ceiling.
CA
3.
13
Installation
5.
Assemble the camera and mounting bracket after
align the front part of the camera and mounting
bracket. Connect the unit by following step a and
b.
Image Adjustment
You can manually adjust the pan/tilt/azimuth angles, focus,
and zoom while observing the connected monitor.
Notes:
14
t
Do not hold the camera by lens unit to adjust panning,
tilting, or azimuth.
t
The video output to the BNC will be interrupted while
a portable monitor is connected to the video jack.
1.
Disassemble the Dome Cover from the main body
by turning it counterclockwise and detach the Lens
-cover.
Installation
2.
Connect a portable monitor to the video jack.
3.
Adjust the pan/tilt/rotate position of the camera.
TILT
ROTATE
PAN
15
Installation
4.
Adjust the zoom.
5.
Adjust the focus.
4-1. Unlock the zoom lever.
5-1. Unlock the focus lever.
4-2. Move the lever to adjust the zoom.
5-2. Move the lever to adjust the focus.
4-3. Lock the lever.
5-3. Lock the lever.
FAR
TELE
Note:
Disassemble the IR cover as
illustrated in case of difficult
occasion to adjust the zoom
lever.
16
NEAR
WIDE
Note:
Disassemble the IR cover as
illustrated in case of difficult
occasion to adjust the focus
lever.
Installation
6.
This camera utilizes an on-screen user MENU. To set
items on the menu, use the following buttons. After
then attach the lens cover and dome cover.
Note:
To disassemble the camera from the mounting bracket,
rotate the camera counterclockwise with pressing the
PUSH button inside the camera body.
17
Menu Operation
OSD Menu control buttons
t
UP button:
Used to move upper direction on the menu screen.
Use this button to select an item or adjust the parameters.
This camera utilizes an on-screen user MENU. To set items
on the menu, use the following buttons.
t
DOWN button:
Used to move lower direction on the menu screen.
Use this button to select an item or adjust the parameters.
t
RIGHT button:
Moves the cursor to the right. Used to increment the
value selected in the menu. The parameter changes
each time this button is pressed.
t
SET
RIGHT
LEFT button:
Moves the cursor to the left. Used to decrement the
value selected in the menu. The parameter changes
each time this button is pressed.
LEFT
DOWN
UP
t
SET button:
Executes selections and displays a submenu for an
item with the mark.
18
Menu Operation
OSD Menu Overview
The following table shows the list of menu items and options. You can adapt the camera to your requirements by
setting up the respective items in these menus.
Main Menu
Sub Menu
ALC /ELC
SHUTTER
OFF / AUTO
EXIT
RET/ TOP / END
-
AWC /
SET KET
MANUAL
EXIT
RED
BLUE
SMART
IR
x512, ..., x2, AUTO, OFF,
A.FLK, 1/160, ..., 1/120 000
SENS-UP
ATW
AUTO
WHITE BAL
DAY/
NIGHT
Contents
BACKLIGHT
OFF/BLC/HSBLC
BRIGHTNESS
0 to 100
AGC
OFF/LOW/MIDDLE/HIGH
EXPOSURE
AUTO
-100 to 100
-100 to 100
RET/ TOP / END
MOTION
DET
DAY
NIGHT
EXIT
BURST
LEVEL
DWELL
TIME
ON/OFF
LOW/ MIDDLE/ HIGH/USER
3 SEC to 60 SEC
-
BURST
ON/OFF
RET/ TOP / END
POSITION ,/
1 to 7
POSITION ;.
SIZE ,/
SIZE ;.
EXIT
OFF
1 to 7
2 to 8
2 to 8
RET/ TOP / END
AREA
1 to 8
SELECTION
STATE
ON / OFF
POSITION
AREA
0 to 7
,/
SETUP
POSITION ;.
0 to 5
SIZE ,/
1 to 8
SIZE ;.
1 to 6
SENSITIVITY
0 to 100
OFF / OUTLINE
DISPLAY
/ MASK1 / MASK2
ALARM
OFF / MESSAGE
OUT
ON
19
Menu Operation
MOTION
ON
DET
3D-DNR 0 to 100
OFF
EXIT
MASK
SELECTION
DISPLAY
RECTANGLE
PRIVACY
MASK
ON
POSITION ,/
POSITION ;.
SIZE ,/
SIZE ;.
MASK
SELECTION
DISPLAY
CIRCLE
20
MASK
SELECTION
RET/ TOP / END
POSITION ,/
POSITION ;.
SIZE ,/
SIZE ;.
RADIUS
1 to 2
OFF /MOSAIC /
ON
POLYGON
PRIVACY
COLOR1 to COLOR8
MASK
SHAPE
POSITION
RET/ TOP / END
EXIT
OFF
ZOOM
x 1.0 to x 16.0
D-ZOOM
ON
PAN
-100 to 100
TILT
-100 to 100
D-EFFECT
OFF / MIRROR / V-FLIP / ROTATE
SHARPNESS
0 to 100
SPECIAL
COLOR
0 to 100
SYNC
INT / LL
USER TITLE
ON / OFF
DISPLAY
1 to 8
OFF / MOSAIC
/ COLOR1 to
COLOR8
2 to 98
2 to 98
4 to 100
4 to 100
1 to 4
OFF /MOSAIC
/ COLOR1 to
COLOR8
0 to 100
0 to 100
1 to 15
1 to 15
1 to 100
LANGUAGE
ENG/CHN/KOR/JAP/FRE/ITA/SPA/POR/DUT/
GER/POL/RUS/TUR/ARA/HEB
EXIT
RET/ TOP / END
Menu Operation
SYSTEM
EXIT
FACTORY RESET
EXIT
RET/ TOP / END
RET/ TOP / END
General Operation
1.
Press [SET] button.
The Main OSD menu screen appears on the monitor.
2.
Use [UP] or [DOWN] button to select an option then
press [SET] button.
Submenu appears on the monitor.
3.
Use [UP] or [DOWN] button to select a submenu
option.
4.
Use [LEFT] or [RIGHT] button to select a value.
5.
Select [EXIT] option then press [SET] to exit the setup
menu. In the submenu, use [UP] or [DOWN] button to
select the [RETURN] then press [SET] to return to the
21
Menu Operation
previous setup menu.
Backlight setting
t
Use Backlight option to view the object clearly in backlight
conditions.
RETURN: Return to the previous.
Exposure Settings
You can set the exposure options using the EXPOSURE
menu.
1.
Select [EXPOSURE] option on the [CAMERA SETTING]
menu.
2.
Use [LEFT] or [RIGHT] button to select a mode.
3.
Press [SET] button and the EXPOSURE menu appears.
1.
Select [Backlight] option.
2.
Use [LEFT] or [RIGHT] button to select a mode then
press [SET].
t
BLC: Camera's backlight compensation feature
helps alleviate issues of visibility in high contrast
areas. Set the BLC limit.
Note:
If the [DAY/NIGHT] option is set to [NIGHT] mode, the BLC
mode of the [EXPOSURE] function is not available and [---]
mark is displayed.
22
Menu Operation
t
HSBLC: Use for masking brightness of the specific
area to view the subject more clearly. The HSBLC
mode is automatically activated only in low
luminance scene.
>
t
AREA SETTING: Use [LEFT] or [RIGHT] button
to select a area then use [UP] or [DOWN]
button to select a [ON] or [OFF]. Press [SET]
to exit the Area setting menu.
> GRAY SCALE: Use [LEFT] or [RIGHT] button to
select a gray scale. (GRAY, D.GRAY, BLACK)
> USER SCALE: Use [LEFT] or [RIGHT] button to
select a bright level. (5 level)
> MASK: Use [LEFT] or [RIGHT] button to select
[ON] or [OFF].
If you set the MASK to ON, the mask
function is activate only when the HSBLC is
automatically activated in low luminance
scene.
OFF: Not used.
BRIGHTNESS setting
You can increase the brightness of the darkened video.
If you set the brightness to lower value, the image is
darkened. If you set the brightness to higher value, the
image gets bright.
1.
Select [BRIGHTNESS] option.
2.
Use [LEFT] or [RIGHT] button to set the bright level.
23
Menu Operation
AGC (Automatic Gain Control) setting
If the images are too dark, change the maximum [AGC]
value to make the images brighter. But noise is increase.
1.
Select [SHUTTER] option.
2.
Use [LEFT] or [RIGHT] button to set shutter speed.
Notes:
1.
Select [AGC] option.
2.
Use [LEFT] or [RIGHT] button to select a mode.
SHUTTER (Shutter Speed) setting
Select the desired shutter speed for camera exposure. You
can change the shutter speed to higher speed to capture
fast-moving subjects, though the image becomes darker.
24
t
When the SHUTTER is set to AUTO, the picture
may become unstable if the camera faces a bright
fluorescent light directly. Therefore, take care when
installing.
t
Set the Shutter OFF when Color Rolling occurs in the
indoor scene. Recommend the Shutter Auto in the
outdoor scene.
Menu Operation
SENS-UP setting
Note:
If pictures are not clear due to darkness, this SENS-UP
operation would increase the sensitivity of picture.
If you set to one of the SHUTTER options except AUTO and
OFF on the [SHUTTER] menu, the [SENS-UP] setting is not
available and [---] mark is displayed.
White Balance settings
Select the method by which the camera shifts its output
colors to compensate for the color of a light source.
1.
Use [UP] or [DOWN] button to select [SENS-UP] option.
2.
Use [LEFT] or [RIGHT] button to select mode.
t
AUTO: Adjust the sensitivity of the picture
automatically.
>
t
SENS-UP LIMIT: Use [LEFT] or [RIGHT] button
to set the SENS-UP limit.
OFF: Not used.
1.
Select [WHITE BAL] option.
2.
Use [LEFT] or [RIGHT] button to select a mode then
press [SET].
t
ATW (Auto-Tracing White Balance): Use [LEFT] or
[RIGHT] button to select the ATW then press [SET]
25
Menu Operation
button.
t
Day/Night Setting
MANUAL: You can set the white balance options
manually.
>
t
t
RED: Obtains the optimum amount of red
gain.
> BLUE: Obtains the optimum amount of blue
gain.
AWC/SET KEY: If you select the AWC/SET
KEY mode, you will be able to set up the White
Balance automatically using [SET] button.
AUTO : Use [LEFT] or [RIGHT] button to select the
AUTO then press [SET] button.
1.
Select [DAY/NIGHT] option.
2.
Use [LEFT] or [RIGHT] button to select mode
for Day/Night function.
t
AUTO: You will be able to change the Day/Night
mode automatically.
Note:
If you set the AGC to [OFF] on the [EXPOSURE]
menu, the AUTO mode of the DAY/NIGHT function is not available and [---] mark is displayed.
>
26
BURST: Use [LEFT] or [RIGHT] button to
select [ON] or [OFF].
Menu Operation
>
LEVEL: Use [LEFT] or [RIGHT] button to select
a level.
>
t
DWELL TIME: Use [LEFT] or [RIGHT] button to
select a dwell time.
DAY: Color mode enabled.
t
NIGHT: Black-and-white mode enabled.
>
SmartIR Setting
SmartIR function improve the sensitivity in the low
luminance. SmartIR analyze the image of the screen,
when the subject is close. Then SmartIR reduce the IR LED
brightness and gain to prevent saturation of the closed
subject.
BURST: Use [LEFT] or [RIGHT] button to
select [ON] or [OFF].
1.
Select [SmartIR] option.
2.
Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
t
POSITION ,/: Moves horizontal position of the
prevent saturation zone.
t
POSITION ;.: Moves vertical position of the
prevent saturation zone.
27
Menu Operation
t
t
SIZE ,/ : Enlarge or decrease the horizontal
size of the prevent saturation zone.
3.
SIZE ;. : Enlarge or decrease the vertical size of
the prevent saturation zone.
Motion Detection Setting
The motion detection detects the moving objects in the
scene by monitoring changes in brightness level. You can
select the level of sensitivity for motion detection to 8
zone.
5.
Select [MOTION DET] option.
2.
Use [LEFT] or [RIGHT] button to select a [ON] and
press [SET]. The MOTION DETECTION menu appears.
28
Use [LEFT] or [RIGHT] button to select a area (1/8
to 8/8) on the [AREA SELECTION].
t
Use [LEFT] or [RIGHT] button to set up the ON or
OFF on the STATE.
t
Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
POSITION ,/: Moves horizontal position
of the mask.
> POSITION ;.: Moves vertical position of
the mask.
> SIZE ,/ : Enlarge or decrease the
horizontal size of the mask.
> SIZE ;. : Enlarge or decrease the vertical
size of the mask.
Use [SENSITIVITY] option to obtain the optimum
detection level.
Use [LEFT] or [RIGHT] button to select the DISPLAY
option.
Use [LEFT] or [RIGHT] button to select the ALARM
OUT option.
>
4.
1.
Select [AREA SETUP] option.
t
6.
Menu Operation
3D-DNR Setting
Privacy Mask Setting
This function is aiming at the protection of personal
privacy, selecting a screen part black not to be displayed in
the screen. Up to 8 zones can be registered.
1.
Select [3D-DNR] option.
If pictures are not clear due to brightness, this option
would reduce the noise of picture.
2.
Use [LEFT] or [RIGHT] button to select a value.
1.
Select [PRIVACY] option.
2.
Use [LEFT] or [RIGHT] button to select a [ON] and
press [SET]. The PRIVACY SETUP menu appears.
t
RECTANGLE :
>
>
Use [LEFT] or [RIGHT] button to select a
mask (MASK1 to MASK8) on the [MASK
SELECTION].
Use [LEFT] or [RIGHT] button to set up the
29
Menu Operation
t
OFF, MOSAIC, COLOR 1 to COLOR 8 on the
DISPLAY option.
> Use [UP] or [DOWN] to select an option then
use [LEFT] or [RIGHT] button to adjust the
option.
POSITION,/: Moves horizontal
position of the mask.
POSITION ;.: Moves vertical position
of the mask.
SIZE ,/: Enlarge or decrease the
horizontal size of the mask.
SIZE ;.: Enlarge or decrease the
vertical size of the mask.
CIRCLE :
>
>
>
30
Use [LEFT] or [RIGHT] button to select a
mask (MASK1 to MASK4) on the [MASK
SELECTION].
Use [LEFT] or [RIGHT] button to set up the
OFF, MOSAIC, COLOR 1 to COLOR 8 on the
DISPLAY option.
Use [UP] or [DOWN] to select an option then
use [LEFT] or [RIGHT] button to adjust the
option.
POSITION ,/: Moves horizontal
position of the mask.
POSITION ;.: Moves vertical position
of the mask.
SIZE ,/: Enlarge or decrease the
horizontal size of the mask.
SIZE ;.: Enlarge or decrease the
vertical size of the mask.
RADIUS SIZE : You can adjust the
RADIUS SIZE (1 to 100).
POLYGON :
-
t
>
>
>
>
Use [LEFT] or [RIGHT] button to select a
mask (MASK1 to MASK2) on the [MASK
SELECTION].
Use [LEFT] or [RIGHT] button to set up the
OFF, MOSAIC, COLOR 1 to COLOR 8 on the
DISPLAY option.
Use the [LEFT], [RIGHT], [UP], [DOWN], [SET]
button to draw the polygon on the [SHAPE].
Use the [LEFT], [RIGHT], [UP], [DOWN],
Menu Operation
[SET] button to move the polygon on the
[POSITION].
Note:
You can adjust the mask color manually except for color 8.
Special Menu Settings
This menu lets you adjust and set up D-ZOOM, D-EFFECT,
SHARPNESS, COLOR, SYNC, USER TITLE, LANGUAGE
function by yourself in the SPECIAL menu.
1.
Select [SPECIAL] option.
2.
Press [SET] button and the SPECIAL menu appears.
31
Menu Operation
t
D-ZOOM (Digital Zoom ) Setting
You can select the digital zoom level.
TILT: Use [LEFT] or [RIGHT] button to move the
screen.
Note:
If you set the [D-ZOOM] to ON, the ZOOM level is set to
[x1.0] automatically.
D-EFFECT (Digital effect) Setting
You can select the digital effect.
1.
Select [D-ZOOM] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to select a [ON] then
press [SET] the DIGITAL ZOOM menu appears. When
you set to ON, the displayed image can be shaking.
3.
Use [UP] or [DOWN] to select a option then use [LEFT]
or [RIGHT] button to select a level.
t
t
32
ZOOM: Use [LEFT] or [RIGHT] button to enlarge
the screen.
PAN: Use [LEFT] or [RIGHT] button to move the
screen.
1.
Select [D-EFFECT] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to select a digital effect.
t
V-FLIP: Flip the picture vertically.
t
ROTATE: Rotate the picture. (180°)
Menu Operation
t
MIRROR: Turn on the mirror effect.
COLOR Setting
t
OFF: Turn off the digital effect.
You can switch the displayed picture to gray scale or color.
SHARPNESS Setting
The degree to which the boundary of the two portions is
clearly distinguished.
1.
Select [SHARPNESS] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to change a adjust the
option. If you set the sharpness value to higher, the
image outline becomes sharp. If you set to lower
value, the image outline becomes dim.
1.
Select [COLOR] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to change a adjust the
option.
33
Menu Operation
SYNC Setting
USER TITLE Setting
You can use the camera identification to assign a number
and character to the camera. To disappear the user title,
select [OFF].
1.
Select [SYNC] option on the [SPECIAL] menu.
2.
The [SYNC] option is set to [INT] automatically.
1.
Select [USER TITLE] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to select a [ON] then
press [SET]. The USER TITLE menu appears.
A
Note:
AC24V Adaptor have to use for [LL] mode setting.
3.
34
Use [UP], [DOWN], [LEFT] or [RIGHT] button to select a
character or number then press [SET] button.
t
CLR: Clear all entered characters and numbers.
t
POS: Move the USER TITLE position on the screen
using the arrow buttons.
t
END: Confirm your selection or exit the setting
Menu Operation
t
t
A (Blank): Inserts a space at the cursor position.
/
SYSTEM Setting
: Moves cursor to left or right.
LANGUAGE Setting
Select the viewer language for the camera setup menu and
OSD information display.
1.
Select the [SYSTEM] menu.
2.
Press [SET] button and the SYSTEM menu appears.
3.
Use [UP] or [DOWN] button to select the option.
t
1.
Select [LANGUAGE] option on the [SPECIAL] screen.
2.
Press [LEFT] or [RIGHT] button to select a language.
4.
FACTORY RESET: To reset the camera setting
to factory setting, select the [FACTORY RESET]
option.
Press [SET] button to confirm your selection.
Note:
The menu screen is move to top menu, after set up [Factory
Reset].
35
Specification
Item
LCD5300R-BN
LCD5300R-BP
Signal System
NTSC
PAL
Image Device
Total/Effective Pixels Number
Horizontal Resolution
520 000 Pixels / 480 000 Pixels
610 000 Pixels / 570 000 Pixels
650 TV Lines (Color), 700 TV Lines (B/W)
ISP
XDI-V
Lens
2.8 mm to 11 mm Vari-focal Lens, F1.2
Minimum
Illumination
(30 IRE)
Color
0.03 lx (Sens-up Off, F1.2), 0.000 3 lx (Sens-up Auto, F1.2),
0.000 1 lx (Sens-up x512, F1.2)
B/W
Day & Night
0 lx (IR LED ON)
ICR (AUTO / DAY / NIGHT)
IRIS Control
DC
Sync. System
Internal / Line Lock
Scanning Frequency (H/V)
36
6 mm (1/3 Type) Exview HAD CCD II
15.734 KHz / 59.94 Hz
15.625 KHz / 50 Hz
S/N Ratio
50 dB
Video Output Signal
1 Vp-p Composite (75 Ω)
IR LED
8 EA
IR Distance
20 m
Specification
Item
LCD5300R-BN
LCD5300R-BP
SmartIR
IR Anti-Saturation
BACKLIGHT
BLC / HSBLC / OFF
DNR
2D + 3D-DNR
Exposure
ALC /ELC
Auto Gain Control
OFF/ LOW/ MIDDLE/ HIGH
Electronic Shutter Speed
Digital Zoom
1/60 to 1/120 000
1/50 to 1/120 000
x16
Sens-up
OFF / AUTO(x2, ... x512)
White Balance
AUTO / ATW / ONE PUSH / MANUAL
Privacy Zone Masking
14 Masks
Motion Detection
8 Zones
Digital Effect
OFF / V-FILP / MIRROR / ROTATE
Communication
Coaxial Communication
Power Source
DC 12 V / AC 24 V
Power Consumption
3.5 W
Input Current
290 mA
37
Specification
Item
LCD5300R-BN
LCD5300R-BP
Operation Temperature/
Humidity
-10 ºC to 50 ºC / 0 % RH to 80 % RH
Storage Temperature/ Humidity
-20 ºC to 60 ºC / 0 % RH to 85 % RH
Dimension (Ø x H)
140 mm x 96 mm
Weight
390 g
38
Download PDF

advertising