LG | LCU5500R-BP | LG LCU5500R-BP Owner’s Manual

OWNER'S MANUAL
IR Bullet Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
LCU5500R-BN
LCU5500R-BP
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle is
intended to alert the user to the presence
of uninsulated dangerous voltage within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
2
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the
modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is
made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment
is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference
to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
•
A suitable conduit entries, knock-outs or glands shall
be provided in the cable entries of this product in the
end user.
•
•
Caution: Danger of explosion if battery is incorrectly
replaced. Replaced only with the same or equivalent
type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s
instructions.
Caution: This installation should be made by a qualified
service person and should conform to all local codes.
Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall be
provided with brushings.
Caution: The apparatus shall not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
Warning: Do not install this equipment in a confined space
such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the
National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
Note:
Please make sure the product is installed appropriate
places where secured from flood, such as under the
eaves, to operate properly. This product is certified as IP66
standard. However, if there is any flood concerns, it is highly
recommended to use an outdoor Housing When you install
the camera inside an outdoor Housing, please use one of
the following methods:
1. Remove the front glass of Housing before installing the
camera.
2.
To keep the front glass of Housing, remove the front
cover, and then put the camera close to the front glass.
Warning: To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
3
LG Electronics hereby declares
that this/these product(s) is/are
in compliance with the essential
requirements and other relevant
provisions of Directive 2004/108/EC
and 2011/65/EU.
European Standards Centre:
Krijgsman 1, 1186 DM Amstelveen The
Netherlands
Disposal of your old appliance
4
1.
All electrical and electronic products
should be disposed of separately from the
municipal waste stream via designated
collection facilities appointed by the
government or the local authorities.
2.
The correct disposal of your old
appliance will help prevent potential
negative consequences for the
environment and human health.
3.
For more detailed information about
disposal of your old appliance,
please contact your city office, waste
disposal service or the shop where you
purchased the product.
4.
EEE Compliance with Directive.
(for Turkey only)
•
Please note that this is NOT a Customer Service
contact point. For Customer Service Information, see
Warranty Card or contact the dealer that you purchased this product.
Important Safety
Instructions
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
9.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
5
Cautions for Safe Operation
Operating and storage location
Power Supply
Avoid viewing a very bright object (such as light fittings)
during an extended period. Avoid operating or storing the
unit in the following locations.
This camera must always be operated DC 12 V or AC 24 V.
Certified/Listed Adaptor which comply with LPS.
•
Extremely hot or cold places (operating temperature
-10 °C to 50 °C, however, we recommend that the unit
be used within a temperature range of 0 °C to 45 °C)
•
Damp or dust place
•
Places exposed to rain
•
Places subject to strong vibration
•
Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
Handling of the unit
Be careful not to spill water or other liquids on the unit. Be
cautions not to get combustible or metallic material inside
the body. If used with foreign matter inside, the camera is
liable to fail or to get cause of fire or electric shock.
•
Remove dust or dirt on the surface of the lens with a
blower.
•
Use a dry soft cloth to clean the body. If it is very dirty,
use a cloth dampened with a small quantity of neutral
detergent then wipe dry.
•
Avoid the use of volatile solvents such as thinners,
alcohol, benzene and insecticides. They may damage
the surface finish and/or impair the operation of the
camera.
6
Contents
3D-DNR Setting........................................................................23
Features.............................................................................. 8
Special Menu Settings...........................................................26
Accessories................................................................................... 8
Part Names and Functions..................................................... 9
Connections..................................................................... 10
Privacy Mask Setting..............................................................24
SYSTEM Setting........................................................................30
Specification.................................................................... 31
Precautions................................................................................10
Connecting Display device..................................................10
Connecting RS-485 Device...................................................11
Connecting power source....................................................11
Connecting Waterproof processing of cable.................12
Menu Operation.............................................................. 13
OSD Menu control buttons..................................................13
OSD Menu Overview..............................................................14
General Operation...................................................................16
Exposure Settings....................................................................16
White Balance settings..........................................................20
Day/Night Setting...................................................................21
SmartIR Setting........................................................................22
Motion Detection Setting.....................................................22
7
Features
Accessories
This IR Bullet Camera is designed for installation in a video
surveillance system.
This manual contains instructions on how to install and
manage the IR Bullet Camera in your video surveillance
system.
Sunshield and Fixing
screw
Should you require any technical assistance, please contact
authorized service center.
•
High resolution and high sensitivity with a 6 mm (1/3
Type) CCD.
•
Day & Night function.
•
HSBLC/BLC covers various light conditions.
•
Weather Proof: IP66 Rating.
Installation sticker
Wrench
Fixing screws
8
Part Names and Functions
a
a Lens Cover
b cd
b Angle adjuster
Adjust the camera angle.
c Tilt adjuster
Adjust the tilt position.
d Pan adjuster
Adjust the pan position.
e IR LED
e
f gh
i j
f IR Sensor
g Focus lock lever
Fixes the focus position after adjusting.
h Zoom lock lever
Fixes the zoom position after adjusting.
i OSD menu control buttons
j Video Out connector (BNC type)
Use this jack for checking the picture with portable
monitor when install the camera.
9
Connections
Connecting Display device
Precautions
The video signal connection between the camera and the
monitor.
•
Be sure to switch off the unit before installation and
connection.
•
The installation should be made by qualified service
personnel or system installers.
•
Do not expose the power and connection cables to
moisture, which may cause damage to the unit.
10
TRX+
WHITE
TRX+
TRX-
BLACK
Connecting RS-485 Device
Connecting power source
Use these ports to connect an external device of RS-485
format.
Connect a power source to the input terminal with 2 and
3 aligned correctly, and then connect a power source to
the power input terminal as shown below. (recommended
power adapter is AC 24 V/0.5 A, DC 12 V/0.5 A or above)
TRX+
TRX-
WHITE
TRX+
BLACK
TRX-
RS-485
Unit
DC 12 V /
AC 24 V
11
Connecting Waterproof processing
of cable
Surely use the Butyl tape.
1. Connect and tape the cables.
2.
12
Bind the cables together with Butyl tape.
Warning:
•
The cables are not waterproofed completely. So sealthe tube ends and the portions between cable cores
as well as connecting portions with Butyl tape.
•
If not using the Butyl tape, it may cause water absorption from a gap and finally condensation and water
leakage.
Menu Operation
OSD Menu control buttons
This camera utilizes an on-screen user MENU. To set items
on the menu, use the following buttons.
UP
SET
LEFT
DOWN
BUTTON
Description
UP
Used to move upper direction on the menu screen.
Use this button to select an item or adjust the
parameters.
DOWN
Used to move lower direction on the menu screen.
Use this button to select an item or adjust the
parameters.
RIGHT
Moves the cursor to the right. Used to increment the
value selected in the menu. The parameter changes
each time this button is pressed.
LEFT
Moves the cursor to the left. Used to decrement the
value selected in the menu. The parameter changes
each time this button is pressed.
SET
Executes selections and displays a submenu for an
item with the mark.
RIGHT
13
OSD Menu Overview
The following table shows the list of menu items and options. You can adapt the camera to your requirements by
setting up the respective items in these menus.
Main Menu
Sub Menu
ALC /ELC
SHUTTER
OFF / AUTO
EXIT
RET/ TOP / END
-
AWC /
SET KET
MANUAL
EXIT
14
RED
BLUE
SMART
IR
x512, ..., x2, AUTO, OFF,
A.FLK, 1/160, ..., 1/120 000
SENS-UP
ATW
AUTO
WHITE BAL
DAY/
NIGHT
Contents
BACKLIGHT
OFF/WDR/BLC/HSBLC
BRIGHTNESS
0 to 100
AGC
OFF/LOW/MIDDLE/HIGH
EXPOSURE
AUTO
-100 to 100
-100 to 100
RET/ TOP / END
MOTION
DET
DAY
NIGHT
EXIT
BURST
LEVEL
DWELL
TIME
ON/OFF
LOW/ MIDDLE/ HIGH/USER
3 SEC to 60 SEC
-
BURST
ON/OFF
RET/ TOP / END
POSITION ,/
1 to 7
POSITION ;.
SIZE ,/
SIZE ;.
EXIT
OFF
1 to 7
2 to 8
2 to 8
RET/ TOP / END
AREA
1 to 8
SELECTION
STATE
ON / OFF
POSITION
AREA
0 to 7
,/
SETUP
POSITION ;.
0 to 5
SIZE ,/
1 to 8
SIZE ;.
1 to 6
SENSITIVITY
0 to 100
OFF / OUTLINE
DISPLAY
/ MASK1 / MASK2
ALARM
OFF / MESSAGE
OUT
EXIT
RET/ TOP / END
ON
3D-DNR 0 to 100
OFF
MASK
SELECTION
DISPLAY
RECTANGLE
PRIVACY
MASK
DISPLAY
ON
CIRCLE
POLYGON
EXIT
POSITION ,/
POSITION ;.
SIZE ,/
SIZE ;.
MASK
SELECTION
POSITION ,/
POSITION ;.
SIZE ,/
SIZE ;.
RADIUS
MASK
SELECTION
DISPLAY
SHAPE
POSITION
RET/ TOP / END
OFF
D-ZOOM
1 to 8
OFF / MOSAIC
/ COLOR1 to
COLOR8
2 to 98
2 to 98
4 to 100
4 to 100
1 to 4
OFF /MOSAIC
/ COLOR1 to
COLOR8
0 to 100
0 to 100
1 to 15
1 to 15
0 to 100
1 to 2
SPECIAL
D-EFFECT
SHARPNESS
COLOR
SYNC
USER TITLE
LANGUAGE
ZOOM
x 1.0 to x 16.0
ON
PAN
-100 to 100
TILT
-100 to 100
OFF / MIRROR / V-FLIP / ROTATE
0 to 100
0 to 100
INT / LL
ON / OFF
ENG/CHN/KOR/JAP/FRE/ITA/SPA/POR/
DUT/GER/POL/RUS/TUR/ARA/HEB
EXIT
FACTORY RESET
RET/ TOP / END
CAMERA ID
OFF / 1 to 255
LG / PELCO-D
PROTOCOL
/ PELCO-P
SYSTEM COMMUNICATION
2400 bps, 4800 bps,
BAUDRATE
9600 bps
SAVE & REBOOT
EXIT
RET/ TOP / END
EXIT
RET/ TOP / END
OFF /MOSAIC
/ COLOR1 to
COLOR8
-
15
General Operation
Exposure Settings
1.
You can set the exposure options using the EXPOSURE
menu.
Press [SET] button.
The Main OSD menu screen appears on the monitor.
2.
Use [UP] or [DOWN] button to select an option then
press [SET] button.
Submenu appears on the monitor.
3.
Use [UP] or [DOWN] button to select a submenu
option.
4.
Use [LEFT] or [RIGHT] button to select a value.
5.
Select [EXIT] option then press [SET] to exit the setup
menu. In the submenu, use [UP] or [DOWN] button to
select the [RETURN] then press [SET] to return to the
previous setup menu.
•
16
RETURN: Return to the previous.
1.
Select [EXPOSURE] option on the [CAMERA SETTING]
menu.
2.
Use [LEFT] or [RIGHT] button to select a mode.
3.
Press [SET] button and the EXPOSURE menu appears.
Backlight setting
Use Backlight option to view the object clearly in backlight
conditions.
•
BLC: Camera's backlight compensation feature
helps alleviate issues of visibility in high contrast
areas. Set the BLC limit.
Note:
If the [DAY/NIGHT] option is set to [NIGHT] mode, the BLC
mode of the [EXPOSURE] function is not available and [---]
mark is displayed.
•
1.
Select [Backlight] option.
2.
Use [LEFT] or [RIGHT] button to select a mode then
press [SET].
•
WDR: WDR (Wide dynamic range) feature can
be very helpful to cope with very challenging
lighting conditions. It is capable of capturing
both of the dark part and bright part and
combining the differences into a scene to
generate a highly realistic image as original
scene. Set the WDR limit.
>
ACE (Adaptive Contrast Enhancement) : This
function is used when you want to display
dark areas of WDR brightly.
HSBLC: Use for masking brightness of the specific
area to view the subject more clearly. The HSBLC
mode is automatically activated only in low
luminance scene.
>
>
>
>
AREA SETTING: Use [LEFT] or [RIGHT] button
to select a area then use [UP] or [DOWN]
button to select a [ON] or [OFF]. Press [SET]
to exit the Area setting menu.
GRAY SCALE: Use [LEFT] or [RIGHT] button
to select a gray scale. (GRAY, D.GRAY, BLACK)
USER SCALE: Use [LEFT] or [RIGHT] button to
select a bright level. (5 level)
MASK: Use [LEFT] or [RIGHT] button to
select [ON] or [OFF].
If you set the MASK to ON, the mask
function is activate only when the HSBLC is
automatically activated in low luminance
scene.
17
•
OFF: Not used.
BRIGHTNESS setting
You can increase the brightness of the darkened video.
If you set the brightness to lower value, the image is
darkened. If you set the brightness to higher value, the
image gets bright.
1.
Select [BRIGHTNESS] option.
2.
Use [LEFT] or [RIGHT] button to set the bright level.
18
AGC (Automatic Gain Control) setting
If the images are too dark, change the maximum [AGC]
value to make the images brighter. But noise is increase.
1.
Select [AGC] option.
2.
Use [LEFT] or [RIGHT] button to select a mode.
SHUTTER (Shutter Speed) setting
SENS-UP setting
Select the desired shutter speed for camera exposure. You
can change the shutter speed to higher speed to capture
fast-moving subjects, though the image becomes darker.
If pictures are not clear due to darkness, this SENS-UP
operation would increase the sensitivity of picture.
1.
Select [SHUTTER] option.
2.
Use [LEFT] or [RIGHT] button to set shutter speed.
Note:
1.
2.
Use [UP] or [DOWN] button to select [SENS-UP]
option.
Use [LEFT] or [RIGHT] button to select mode.
•
When the SHUTTER is set to AUTO, the picture may
become unstable if the camera faces a bright fluorescent
light directly. Therefore, take care when installing.
AUTO: Adjust the sensitivity of the picture
automatically.
>
•
SENS-UP LIMIT: Use [LEFT] or [RIGHT] button
to set the SENS-UP limit.
OFF: Not used.
19
Note:
•
If you set to one of the SHUTTER options except AUTO on
the [SHUTTER] menu, the [SENS-UP] setting is not available
and [---] mark is displayed.
White Balance settings
Select the method by which the camera shifts its output
colors to compensate for the color of a light source.
1.
Select [WHITE BAL] option.
2.
Use [LEFT] or [RIGHT] button to select a mode then
press [SET].
•
20
ATW (Auto-Tracing White Balance): Use [LEFT] or
[RIGHT] button to select the ATW then press [SET]
button.
MANUAL: You can set the white balance options
manually.
>
•
•
RED: Obtains the optimum amount of red
gain.
> BLUE: Obtains the optimum amount of blue
gain.
AWC/SET KEY: If you select the AWC/SET
KEY mode, you will be able to set up the White
Balance automatically using [SET] button.
AUTO : Use [LEFT] or [RIGHT] button to select the
AUTO then press [SET] button.
Day/Night Setting
>
•
DWELL TIME: Use [LEFT] or [RIGHT] button
to select a dwell time.
DAY: Color mode enabled.
•
NIGHT: Black-and-white mode enabled.
>
1.
Select [DAY/NIGHT] option.
2.
Use [LEFT] or [RIGHT] button to select mode
for Day/Night function.
•
BURST: Use [LEFT] or [RIGHT] button to
select [ON] or [OFF].
AUTO: You will be able to change the Day/Night
mode automatically.
Note:
If you set the AGC to [OFF] on the [EXPOSURE]
menu, the AUTO mode of the DAY/NIGHT function is not available and [---] mark is displayed.
>
>
BURST: Use [LEFT] or [RIGHT] button to
select [ON] or [OFF].
LEVEL: Use [LEFT] or [RIGHT] button to
select a level.
21
SmartIR Setting
SmartIR function improve the sensitivity in the low
luminance. SmartIR analyze the image of the screen,
when the subject is close. Then SmartIR reduce the IR LED
brightness and gain to prevent saturation of the closed
subject.
•
SIZE ;. : Enlarge or decrease the vertical size of
the prevent saturation zone.
Motion Detection Setting
The motion detection detects the moving objects in the
scene by monitoring changes in brightness level. You can
select the level of sensitivity for motion detection to 8 zone.
1.
Select [SmartIR] option.
2.
Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
1.
Select [MOTION DET] option.
•
POSITION ,/: Moves horizontal position of the
prevent saturation zone.
2.
Use [LEFT] or [RIGHT] button to select a [ON] and press
[SET]. The MOTION DETECTION menu appears.
•
POSITION ;.: Moves vertical position of the
prevent saturation zone.
3.
•
22
SIZE ,/ : Enlarge or decrease the horizontal size
of the prevent saturation zone.
Select [AREA SETUP] option.
•
Use [LEFT] or [RIGHT] button to select a area (1/8
to 8/8) on the [AREA SELECTION].
•
Use [LEFT] or [RIGHT] button to set up the ON or
OFF on the STATE.
•
Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
>
4.
5.
6.
POSITION ,/: Moves horizontal position
of the mask.
> POSITION ;.: Moves vertical position of
the mask.
> SIZE ,/ : Enlarge or decrease the
horizontal size of the mask.
> SIZE ;. : Enlarge or decrease the vertical
size of the mask.
Use [SENSITIVITY] option to obtain the optimum
detection level.
Use [LEFT] or [RIGHT] button to select the DISPLAY
option.
Use [LEFT] or [RIGHT] button to select the ALARM
OUT option.
3D-DNR Setting
1.
Select [3D-DNR] option.
If pictures are not clear due to brightness, this option
would reduce the noise of picture.
2.
Use [LEFT] or [RIGHT] button to select a value.
23
Privacy Mask Setting
This function is aiming at the protection of personal
privacy, selecting a screen part black not to be displayed in
the screen. Up to 8 zones can be registered.
•
use [LEFT] or [RIGHT] button to adjust the
option.
-
POSITION,/: Moves horizontal
position of the mask.
-
POSITION ;.: Moves vertical position
of the mask.
-
SIZE ,/: Enlarge or decrease the
horizontal size of the mask.
-
SIZE ;.: Enlarge or decrease the
vertical size of the mask.
CIRCLE :
>
1.
Select [PRIVACY] option.
2.
Use [LEFT] or [RIGHT] button to select a [ON] and press
[SET]. The PRIVACY SETUP menu appears.
•
RECTANGLE :
>
>
>
24
Use [LEFT] or [RIGHT] button to select a
mask (MASK1 to MASK8) on the [MASK
SELECTION].
Use [LEFT] or [RIGHT] button to set up the
OFF, MOSAIC, COLOR 1 to COLOR 8 on the
DISPLAY option.
Use [UP] or [DOWN] to select an option then
>
>
Use [LEFT] or [RIGHT] button to select a
mask (MASK1 to MASK4) on the [MASK
SELECTION].
Use [LEFT] or [RIGHT] button to set up the
OFF, MOSAIC, COLOR 1 to COLOR 8 on the
DISPLAY option.
Use [UP] or [DOWN] to select an option then
use [LEFT] or [RIGHT] button to adjust the
option.
-
POSITION ,/: Moves horizontal
position of the mask.
-
POSITION ;.: Moves vertical position
of the mask.
-
•
SIZE ,/: Enlarge or decrease the
horizontal size of the mask.
-
SIZE ;.: Enlarge or decrease the
vertical size of the mask.
-
RADIUS SIZE : You can adjust the
RADIUS SIZE (0 to 100).
POLYGON :
>
>
>
>
Use [LEFT] or [RIGHT] button to select a
mask (MASK1 to MASK2) on the [MASK
SELECTION].
Use [LEFT] or [RIGHT] button to set up the
OFF, MOSAIC, COLOR 1 to COLOR 8 on the
DISPLAY option.
Use the [LEFT], [RIGHT], [UP], [DOWN], [SET]
button to draw the polygon on the [SHAPE].
Use the [LEFT], [RIGHT], [UP], [DOWN],
[SET] button to move the polygon on the
[POSITION].
Note:
You can adjust the mask color manually except for color 8.
25
Special Menu Settings
This menu lets you adjust and set up D-ZOOM, D-EFFECT,
SHARPNESS, COLOR, SYNC, USER TITLE, LANGUAGE
function by yourself in the SPECIAL menu.
1.
Select [SPECIAL] option.
2.
Press [SET] button and the SPECIAL menu appears.
26
D-ZOOM (Digital Zoom ) Setting
You can select the digital zoom level.
1.
Select [D-ZOOM] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to select a [ON] then
press [SET] the DIGITAL ZOOM menu appears. When
you set to ON, the displayed image can be shaking.
3.
Use [UP] or [DOWN] to select a option then use [LEFT]
or [RIGHT] button to select a level.
•
ZOOM: Use [LEFT] or [RIGHT] button to enlarge
the screen.
•
PAN: Use [LEFT] or [RIGHT] button to move the
screen.
•
TILT: Use [LEFT] or [RIGHT] button to move the
screen.
Note:
SHARPNESS Setting
The degree to which the boundary of the two portions is
clearly distinguished.
If you set the [D-ZOOM] to ON, the ZOOM level is set to
[x1.0] automatically.
D-EFFECT (Digital effect) Setting
You can select the digital effect.
1.
2.
1.
Select [SHARPNESS] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to change a adjust the
option. If you set the sharpness value to higher, the
image outline becomes sharp. If you set to lower
value, the image outline becomes dim.
Select [D-EFFECT] option on the [SPECIAL] menu.
Use [LEFT] or [RIGHT] button to select a digital effect.
•
V-FLIP: Flip the picture vertically.
•
ROTATE: Rotate the picture. (180°)
•
MIRROR: Turn on the mirror effect.
•
OFF: Turn off the digital effect.
27
COLOR Setting
SYNC Setting
You can switch the displayed picture to gray scale or color.
1.
Select [SYNC] option on the [SPECIAL] menu.
1.
Select [COLOR] option on the [SPECIAL] menu.
2. The [SYNC] option is set to [INT] automatically.
2.
Use [LEFT] or [RIGHT] button to change a adjust the
option.
Note:
28
LCU5300-EN Model support only INT(INTERNAL) in SYNC.
USER TITLE Setting
LANGUAGE Setting
You can use the camera identification to assign a number
and character to the camera. To disappear the user title,
select [OFF].
Select the viewer language for the camera setup menu and
OSD information display.
1.
Select [USER TITLE] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to select a [ON] then
press [SET]. The USER TITLE menu appears.
A
3.
1.
Select [LANGUAGE] option on the [SPECIAL] screen.
2.
Press [LEFT] or [RIGHT] button to select a language.
Use [UP], [DOWN], [LEFT] or [RIGHT] button to select a
character or number then press [SET] button.
•
CLR: Clear all entered characters and numbers.
•
POS: Move the USER TITLE position on the screen
using the arrow buttons.
•
END: Confirm your selection or exit the setting
•
A (Blank): Inserts a space at the cursor position.
•
/
: Moves cursor to left or right.
29
SYSTEM Setting
4.
communication settings.
Press [SET] button to confirm your selection.
Notes:
1.
Select the [SYSTEM] menu.
2.
Press [SET] button and the SYSTEM menu appears.
3.
Use [UP] or [DOWN] button to select the option.
•
FACTORY RESET: To reset the camera setting
to factory setting, select the [FACTORY RESET]
option.
•
COMMUNICATION
>
>
>
30
>
CAMERA ID: You can use the camera
identification [CAMERA ID] to assign a
number to the camera. Use [LEFT] or [RIGHT]
to select a CAMERA ID.
PROTOCOL: Select a protocol for RS-485
communication.
BAUD RATE: Set the speed of communication
between the camera and the RS-485 unit.
SAVE & REBOOT: To confirm the
•
You need to set up [Save & Report] for save [Camera
ID], [Protocol], [Baud & Rate] changes.
•
The menu screen is move to top menu, after set up
[Factory Reset].
Specification
Item
LCU5500R-BN
Signal System
NTSC
LCU5500R-BP
PAL
Image Sensor
6 mm (1/3 Type) CCD
Lens
2.8 mm to 11 mm Vari-focal Lens, F1.2
Color
Horizontal
Resolution
650 TV Lines
B/W
Day & Night
Sens-up
Minimum
Illumination
(30 IRE)
S/N Ratio
700 TV Lines
ICR (AUTO / DAY / NIGHT)
OFF / AUTO(x2, ... x512)
Color
0.2 lx @ Sens-up OFF, F1.2
B/W
0 lx @ IR LED ON
50 dB
Digital Zoom
X16
Sync. System
Internal / Line Lock
Video Output
Electronic Shutter
1 Vp-p Composite (75 Ω)
1/60 to 1/120 000
1/50 to 1/120 000
Motion Detection
8 Zones
IR LED
IR LED 32 EA, 50 M Distance, SmartIR
31
Item
LCU5500R-BN
Communication
LCU5500R-BP
RS-485, Coaxial Communication
RS-485
LG, Pelco-D, Pelco-P
Backlight Compensation
OFF / WDR / BLC / HSBLC
Privacy Masking
14 Masks
DNR
2D + 3D-DNR
Protection
IP66
Power Source
DC 12 V / AC 24 V
Power
Consumption
DC 12 V
AC 24 V
490 mA
390 mA
Operating Temperature/ Humidity
-10 ºC to 50 ºC / 0 % RH to 80 % RH
Storage Temperature/ Humidity
-20 ºC to 60 ºC / 0 % RH to 90 % RH
Dimension (W x H x D)
84 mm x 83.5 mm x 320 mm
Weight
1.3 kg
32
Download PDF