LG | LCP3750T-AP | LG LCP3750T-AP Owner’s Manual

OWNER’S MANUAL
Dome Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
LCP3750T Series
LCP3750 Series
2
1
Safety Information
Safety Information
1
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
FCC WARNING: This equipment may generate or use
radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the
modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is
made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
•
A suitable conduit entries, knock-outs or glands shall
be provided in the cable entries of this product in the
end user.
•
Caution: Danger of explosion if battery is incorrectly
replaced. Replaced only with the same or equivalent
type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s
instructions.
•
Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall be
provided with brushings.
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
Warning: Do not install this equipment in a confined
space such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the
National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
Safety Information
Warning: To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
Caution: This installation should be made by a qu alified
service person and should conform to all local codes.
Caution: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, should be placed on the apparatus.
To disconnect power from mains, pull out the mains cord
plug. When instal ling the product, ensure that the plug
is easily accessible.
LG Electronics hereby declares that this/
these product(s) is/are in compliance
with the essential requirements and other
relevant provisions of Directive 2004/108/
EC and 2011/65/EU.
Contact office for compliance of this
product :
LG Electronics Inc.
EU Representative, Krijgsman 1,
1186 DM Amstelveen, The Netherlands
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it means
the product is covered by the European
Directive 2002/96/EC.
2. All electrical and electronic products
should be disposed of separately from the
municipal waste stream via designated
collection facilities appointed by the
government or the local authorities.
3. The correct disposal of your old appliance
will help prevent potential negative
consequences for the environment and
human health.
4. For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you purchased
the product.
EEE Compliance with Directive. (for Turkey only)
Disposal of waste batteries/accumulators
1. When this crossed-out wheeled
bin symbol is attached to batteries/
accumulators of Your product it means
they are covered by European Directive
2006/66/EC.
2. This symbol may be combined with
chemical symbols for mercury(Hg),
cadmium(Cd) or lead(Pb) if the battery
Contains more that 0.0005% of mercury,
0.002% of cadmium or 0.004% of lead.
3. All batteries/accumulators should be
disposed separately from the municipal
waste stream via designated collection
facilities appointed by the government or
the local authorities.
4. The correct disposal of Your old batteries/
accumulators will help to prevent
potential negative consequences for the
environment, animal and human health.
5. For more detailed information
about disposal of Your old batteries/
accumulators, please contact Your city
office, waste disposal service or the shop
where You purchased the product.
1
Safety Information
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
3
4
Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
1
Safety Information
1. Read these instructions.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
Safety Precautions
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat re gisters, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
•
Do not attempt to disassemble the camera
To prevent electric shock, do not remove screws or
covers. There are no user serviceable parts inside. Ask a
qualified service personnel for servicing.
•
Avoid the camera with direct sunlight
Do not aim the camera at bright objects.Whether the
camera is in use or not, never face it with direct sunlight
or other extremely bright objects. Otherwise blooming
or smear may be caused.
•
Handle the camera with care
Do not abuse the camera. Avoid striking, shaking, etc.
The camera could be damaged by improper handling
or storage.
•
Do not use strong solvents or detergents
Use a dry cloth to the camera when it is dirty. If it is
hard to remove the dirt on the camera, use a mild
detergent and wipe it gently.
•
Do not install this camera upside down
This camera is designed for mounting on the ceiling or
wall.If you install this camera upside down, for example,
mounted on the floor, it may cause malfunction.
•
Do not use the camera in such places as shown below.
The lens may become cloudy due to condensation if
the camera is used under the following conditions.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
››
Rapid temperature fluctuation by switching an air
conditioner on and off.
››
Rapid temperature fluctuation due to frequent
door opening and closing.
››
Use in an environment where eyeglasses become
foggy.
››
Use in a room filled with cigarette smoke or dust.
If the lens becomes cloudy due to condensation,
remove the dome cover and wipe all moist surfaces
with a soft cloth.
Safety Information
•
Consumables
Parts having contacts such as the lens-drive motors,
cooling fan built inside the camera are subject to wear
with time. About replacement and maintenance of
such parts, please ask the nearest service center.
About Static Electricity Removal
Before installing the camera, touch a metal case or other
metallic parts with your hand to remove static electricity
from your body.
Do not install in areas subjected to high amounts of
humidity or dust.
Doing so may cause internal components to damage more
easily or malfunction.
Do not wire cables near power lines.
Tightening the Screws
Camera Installation Location
Discuss the installation location for the camera with your
retailer, and select a place that is strong enough
for the installation.
•
Install the camera on a ceiling (concrete, etc.) at a
location that is sufficiently strong to support it.
•
Install the camera body on the foundation section
of the building or sections having sufficient bearing
strength.
Never install or use the camera in the following
locations
•
Do not install it in areas exposed to direct sunlight or
rain.
•
Do not install the camera near the air outlet of an air
conditioner.
•
Near a swimming pool or other areas where chemicals
are used.
•
Food preparation areas and other locations where there
are large amounts of steam vapor and oil, in flammable
atmospheres, other special environments.
•
Areas where radiation, X-rays, strong electric waves, or
magnetism is generated.
•
At sea, in coastal areas, or in areas where corrosive gas
is being generated.
•
Areas outside of the allowable ambient operating
temperature range.
Screws should be tightened sufficiently in accordance with
the materials and structure of the installation location. After
tightening the screws, visually inspect them to make sure
there is no unevenness and that each screw is tight.
1
Safety Information
•
Before operating, please check proper temperature,
humidity and power source ratings.
Use the camera under conditions where temperature
is from -20 °C to 50 °C and humidity is below 80 %. The
input power source is AC 24 V.
5
6
Contents
Contents
1
Safety Information
4
IMPORTANT SAFETY INSTRUCTIONS
4
Safety Precautions
15
Connecting LKD1000 controller
15
Connecting RS-485 device
16
Connecting power source
16
Protocol and baud rate settings
17
Camera ID Setting
20
Removing the Protection Tape
21
Mounting the camera
21
Wall mount (optional)
23
Pendant mount (Optional)
4
Operation
2
Preparation
27
Setup Menu Overview
31
Menu navigation
8Introduction
31
8Features
31
General operation
9Accessories
32
Camera menu settings
10
32
Focus setting
32
Exposure settings
33
White Balance setting
34
Day/Night setting
34
3D-DNR setting
35
Color setting
35
Sharpness setting
35
Stabilizer setting
Part Names and Functions
3
Installation
11Connections
11Precautions
Accessing the camera setup menu
11
Basic Connection Overview
12
Connecting Display device
35
PAN/TILT Settings
12
ALARM input connection
35
Preset setting
14
ALARM output connections
37
Group tour setting
37
Pattern setting
Contents
38
Auto Pan setting
38
Privacy Mask setting
39
Special setting
41
Auto Tracking setting (Optional)
43
1
OSD Settings
43
User title setting
43
ZOOM MAG setting
43
FUNCTION setting
44
DOME ID setting
44
LANGUAGE Setting
44
ALARM Setting
44
Alarm In setting
45
Alarm Out setting
45
7
2
3
4
RESET Setting
45Information
45Initialization
45
Camera reset
45
Factory reset
5
Appendix
46Specifications
5
8
Preparation
2
Preparation
2
Preparation
Introduction
•
A routine of manual operations can be stored and
reproduced repeatedly. The Pan, Tilt and Zoom controls
are available for pattern recording.
The dome cameras are designed for installation in an
outdoor video surveillance system.
The camera incorporates the digital signal processor, pan/
tilt mechanism, zoom lens and RS-485 communication
interface in a compact outdoor enclosure.
,,Note
The available total time of pattern differs depending
on camera’s operation. When the pattern recording is
full, the pattern recording will automatically stop.
•
•
Preset Position
Preset position is the function to register camera
monitoring positions (preset positions). By using
LKD1000 controller, you can register presets with
position number. Maximum 256 Preset Positions
(LCP3750T series: Maximum 240 Preset Positions) are
available. By entering the position numbers, you can
move cameras to the preset positions. The moving
speed and holding time are adjustable.
•
Preset Tour
Preset Tour is the function to go through all the
registered camera monitoring positions (preset
positions). During the working PRESET TOUR, The
FOCUS could not be operated properly under -20 °C .
•
Group Tour
Maximum 10 group tours are able to compose the
group of preset, pattern, auto pan that the operator
can program to be linked together in a sequence.
Auto Pan
The camera has an Auto Pan function that enables to
keep surveillance on every detail occurring around the
specific area, which is preset to watch in advance. The
camera can pan among the maximum 8 points you will
set. The moving speed and holding time are adjustable.
High Sensitivity Support
The camera provides the high quality picture with
4.5 mm (1/4 Type) Super HAD II CCD.
•
Privacy Mask
Privacy zone feature enables users to veil unwanted
zones. This setting is used for masking unwanted zones,
hiding them from display on the monitor screen. Up to
8 zones can be registered.
Features
•
Pattern recording function
•
Auto Flip
When the camera is operated to tilt through the 90°, it
can be watched the opposite side of the locations by
Auto Flip of a 180° horizontally.
•
Optical Zoom
--
•
The optical zoom range is 1x to 37x.
Digital Zoom
Digital zoom enhances the systems zoom range to 12
times beyond the optical zoom limit.
Total system zoom range is below.
--
•
37x (1x digital zoom) to 444x (12x digital zoom)
Alarm In function (4 channels)
Alarm input signals are supplied from external devices
through the ALARM IN connector to activate ‘go to
preset’ function.
Preparation
•
Alarm Out function (2 channels)
When alarm inputs are supplied via the alarm input
connector on the camera, the camera sends output
signals via the alarm output connector on the camera.
•
Accessories
Controls by General Controller
This camera can be controlled by RS-485. Especially the
camera has an excellent cost-saving effect because it
can be controlled by the general RX point of contact
signal.
•
Camera main cable
Connects with the maximum 256 cameras
Day & Night Function
This camera can be selected Color or Black & White. You
can set Color in the daytime and Black & White at night
due to the low illumination. (Filter Conversion type)
•
DSS (Digital Slow Shutter) function
Wrench
It is possible to highly sensitive surveillance because of
DSS(Digital Slow Shutter) function.
•
WDR (Wide Dynamic Range) function
The camera can be best condition to watch easily
inside or outside in the strong back light.
•
Power Supply
This camera must always be operated a AC 24 V.
Certified/Listed Adaptor which comply with LPS.
2
Preparation
This camera can be utilized after being connected
with maximum 256 cameras. Therefore, it is capable of
performing an excellent job in the large buildings or
department stores.
•
9
PIPE Installation Bracket
10
Preparation
Part Names and Functions
a
a
BNC connector cover cap
b
Video output BNC connector
Supplies analog video signal (composite) to the
connected device.
b
c
c
RS-485 Data Communication
d
Alarm In Data Terminal
Input data terminal for alarm (relay) signal.
2
d
Preparation
e
f
e
Output data terminal for alarm (relay) signal.
f
Power input Terminal
Connects to a AC 24 V power supply using proper
cables.
g
g
Alarm Out Data Terminal
Dome Cover
Installation
11
3
Installation
Connections
Precautions
The following steps of installation and connection work should be done by qualified service personnel or system
installers and should conform to all local codes.
•
Before you install and connect the camera, check and prepare the required peripheral devices and cables.
•
Before you connect the camera, turn off all devices to be connected, such as this camera and DVR.
•
Do not touch the dome cover’s window.
Basic Connection Overview
3
Installation
•
12
Installation
Connecting Display device
The video signal connection between the camera and the
monitor.
Display device connection
>>Caution
Do not connect one alarm sensor to the several
camera’s alarm input connector.
Alarm input connection
3
A
Alarm device
Installation
B
Alarm device
C
Alarm device
D
E
Adaptor Cable
Alarm device
Alarm In Data Terminal
Adaptor cable
No
Description
ALARM input connection
A
ALARM IN 1
You can connect up to 4 alarm sensors to the camera. Each
alarm sensor should be connected with Alarm IN COM. You
can adjust the signal state to NO (normally open) or NC
(normally closed) through the setup menu.
B
ALARM IN 2
C
ALARM IN COM
D
ALARM IN 3
E
ALARM IN 4
1. Connect the Adapter cable to the Alarm In Data
Terminal of the camera.
2. Connect the alarm device to the Adaptor cable.
When connecting lines, check and connect the color
lines of the each device correctly. Refer to the below
tables for color line information.
Installation
13
Alarm Input function
Alarm In Data Terminal
Description
Color
ALARM IN 1
Pink
ALARM IN 2
Gray
ALARM IN COM
Yellow
ALARM IN 3
White
ALARM IN 4
Violet
This speed dome camera has a terminal that can sense the
alarm signals.
If the alarm sensor that has installed in a door, window,
safe etc. sense a touch or shock, the alarm sensor send the
alarm signal to the camera and the camera will observe the
sensed position.
Change the observe position to a sensor that senses a
touch or shock then return to the position that previously
observed. (Set the Duration Time of Alarm Input function
to “3 to 255”.)
Function status
Mode
While operating
Preset Tour
function.
Stop preset touring and change the
observe position to the alarmed
position then restart the preset
touring again.
Stop auto panning and change the
While operating
observe position to the alarmed
Auto Pan function. position then restart the auto
panning again.
While operating
Pattern function.
Stop operating pattern function
and change the observe position
to the alarmed position during the
dwell time then restart the pattern
function again.
in case of HOME
POSITION is ON.
After Alarm has been cleared and
finished the dwell time, it moves to
the HOME POSITION and spend the
dwell time at that position.
,,Note
Do not connect one alarm sensor to the several
camera’s alarm input connector.
3
Installation
While observe a
specific position.
Change the observe position to the
alarmed position then return to the
position that previously observed.
14
Installation
ALARM output connections
No
Description
A
ALARM OUT [NO1]
B
ALARM OUT [COM1]
C
ALARM OUT [NC1]
D
NC
E
ALARM OUT [NO2]
F
ALARM OUT [COM2]
3
G
ALARM OUT [NC2]
Installation
Connect the alarm device to the alarm output data port.
Alarm signal output at an event occurrence. You can set the
Alarm Output to the normal open or normal close mode.
Adaptor cable
H
NC
1. Connect the adaptor cable to the Alarm Out Data
Terminal of the camera.
2. Connect the alarm device to the adaptor cable.
When connecting lines, check and connect the color
lines of the each device correctly. Refer to the below
tables for color line information.
Alarm Out connection
A
Alarm device
device
Alarm
Alarm Out Data Terminal
Alarmdevice
device
Alarm
Description
Color
ALARM OUT [NO1]
White Blue
ALARM OUT [COM1]
Beige
ALARM OUT [NC1]
Black
ALARM OUT [NO2]
Brown
ALARM OUT [COM2]
Red
ALARM OUT [NC2]
Orange
B
C
D
E
F
Alarmdevice
device
Alarm
Alarmdevice
device
Alarm
Adaptor Cable Alarm Out Data Terminal
TXInstallation
Connecting LKD1000 controller
15
RS-485 connection
1. Connect the adaptor cable to the RS-485 Data
Communication of the camera.
2. Connect the LKD1000 controller to the adaptor cable.
(Refer to the manuals of the LKD1000 controller for
more details.)
LKD1000 connection
A
RS-485device
device
RS-485
B
TX+
3
A
Adaptor cable
TX-
RS-485 Data
Communication
1. Connect the adaptor cable to the RS-485 Data
Communication of the camera.
RS-485 Data
Communication
Adaptor cable
Adaptor cable
2. Connect the RS-485 device to the adaptor cable.
When connecting lines, connect the “Orange color line”
of the RJ-45 Adapter cable to “RX -” of the RS-485 unit
and “White color line” of the RJ-45 Adapter cable to “RX
+” of the RS-485 unit correctly.
Adaptor cable
No
Description
No
Description
A
RS-485 +
A
RS-485 +
RS-485 -
B
RS-485 -
B
A
RS-485 device
B
Connecting RS-485 device
Use the cable that is described below for RS-485 site
communication.
•
Shielded, twisted pair cable
•
Low impedance
•
Wire gauge size is thicker than AWG #22 (0.33 mm2).
Data Communication Terminal
Description
Color
RS-485 +
Green
RS-485 -
Blue
Installation
B
16
Installation
Connecting power source
Connect a AC 24 V power source to the power input jack.
(Recommended power adapter is AC 24 V/2 A or above)
Baud Rate setting
ON
ON
OFF
Protocol and baud rate settings
The camera has one 8-bit DIP switch blocks that determine
the protocol and baud rate of the data communication.
Settings are loaded when the camera boots up. Be sure to
turn the camera off, change the DIP switch settings, and
then power the camera back up to load the changes.
SW1
SW2
SW3
SW4
BAUD RATE
(BPS)
OFF
OFF
OFF
OFF
9 600
1. Turn off the camera.
OFF
OFF
OFF
ON
2 400
OFF
OFF
ON
OFF
4 800
OFF
ON
OFF
OFF
19 200
ON
OFF
OFF
OFF
38 400
ON
ON
ON
ON
OSD Set
2. Remove the dome cover.
3
3. Remove the camera assembly cover.
DIP switch position
Installation
Protocol setting
ON
4. Set the DIP switches.
DIP switch locations
ON
OFF
DIP switch position
Protocol
SW5
SW6
SW7
SW8
OFF
OFF
OFF
OFF
LG Multix
OFF
ON
OFF
OFF
Pelco C
OFF
OFF
OFF
ON
Pelco D
OFF
OFF
ON
OFF
Pelco P
ON
ON
ON
ON
OSD Set
,,Note
If you are not using the controller with LG Multix
protocol, there may be some limitation of function
control.
5. Assemble the dome cover and the camera assembly
cover in the reverse order.
6. Power up the camera to load the changes.
Installation
Camera ID Setting
28
The camera’s ID is set to “0” as factory default. If you use
two or more cameras simultaneously, change the ID of the
cameras.
Set the camera ID setting referring to the pictures and the
table on the below.
ON
ON
OFF
OFF OFF
ON
ON
ON
OFF OFF OFF
29
ON
OFF
ON
ON
ON
OFF OFF OFF
30
OFF
ON
ON
ON
ON
OFF OFF OFF
31
ON
ON
ON
ON
ON
OFF OFF OFF
32
OFF OFF OFF OFF OFF
ON
OFF OFF
33
ON
OFF OFF OFF OFF
ON
OFF OFF
34
OFF
ON
OFF OFF OFF
ON
OFF OFF
35
ON
ON
OFF OFF OFF
ON
OFF OFF
36
OFF OFF
ON
OFF OFF
ON
OFF OFF
37
ON
OFF
ON
OFF OFF
ON
OFF OFF
SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8
38
OFF
ON
ON
OFF OFF
ON
OFF OFF
0
OFF OFF OFF OFF OFF OFF OFF OFF
39
ON
ON
ON
OFF OFF
ON
OFF OFF
1
ON
OFF OFF OFF OFF OFF OFF OFF
40
OFF OFF OFF
ON
OFF
ON
OFF OFF
2
OFF
ON
OFF OFF OFF OFF OFF OFF
41
ON
OFF OFF
ON
OFF
ON
OFF OFF
3
ON
ON
OFF OFF OFF OFF OFF OFF
42
OFF
ON
OFF
ON
OFF
ON
OFF OFF
ON
ON
OFF
ON
OFF
ON
OFF OFF
4
OFF OFF
ON
OFF OFF OFF OFF OFF
43
5
ON
ON
OFF OFF OFF OFF OFF
44
OFF OFF
ON
ON
OFF
ON
OFF OFF
ON
OFF
ON
ON
OFF
ON
OFF OFF
OFF
6
OFF
ON
ON
OFF OFF OFF OFF OFF
45
7
ON
ON
ON
OFF OFF OFF OFF OFF
46
OFF
ON
ON
ON
OFF
ON
OFF OFF
ON
ON
ON
ON
OFF
ON
OFF OFF
8
OFF OFF OFF
ON
OFF OFF OFF OFF
47
9
ON
ON
OFF OFF OFF OFF
48
OFF OFF OFF OFF
ON
ON
OFF OFF
ON
OFF OFF OFF
ON
ON
OFF OFF
OFF OFF
10
OFF
ON
OFF
ON
OFF OFF OFF OFF
49
11
ON
ON
OFF
ON
OFF OFF OFF OFF
50
OFF
ON
OFF OFF
ON
ON
OFF OFF
ON
ON
OFF OFF
ON
ON
OFF OFF
12
OFF OFF
ON
ON
OFF OFF OFF OFF
51
13
ON
ON
ON
OFF OFF OFF OFF
52
OFF OFF
ON
OFF
ON
ON
OFF OFF
ON
OFF
ON
OFF
ON
ON
OFF OFF
OFF
14
OFF
ON
ON
ON
OFF OFF OFF OFF
53
15
ON
ON
ON
ON
OFF OFF OFF OFF
54
OFF
ON
ON
OFF
ON
ON
OFF OFF
ON
OFF OFF OFF
55
ON
ON
ON
OFF
ON
ON
OFF OFF
OFF OFF OFF
ON
ON
ON
OFF OFF
16
OFF OFF OFF OFF
17
ON
OFF OFF OFF
ON
OFF OFF OFF
56
18
OFF
ON
ON
OFF OFF OFF
57
ON
OFF OFF
ON
ON
ON
OFF OFF
OFF
ON
OFF
ON
ON
ON
OFF OFF
19
ON
ON
20
OFF OFF
OFF OFF
OFF OFF
ON
OFF OFF OFF
58
ON
ON
OFF OFF OFF
59
ON
ON
OFF
ON
ON
ON
OFF OFF
OFF OFF
ON
ON
ON
ON
OFF OFF
OFF
21
ON
OFF
ON
OFF
ON
OFF OFF OFF
60
22
OFF
ON
ON
OFF
ON
OFF OFF OFF
61
ON
OFF
ON
ON
ON
ON
OFF OFF
OFF
ON
ON
ON
ON
ON
OFF OFF
ON
ON
ON
ON
ON
OFF OFF
23
ON
ON
OFF
ON
OFF OFF OFF
62
24
OFF OFF OFF
ON
ON
OFF OFF OFF
63
ON
OFF OFF OFF OFF OFF OFF
ON
OFF
ON
25
ON
OFF OFF
ON
ON
OFF OFF OFF
64
26
OFF
ON
ON
ON
OFF OFF OFF
65
ON
OFF OFF OFF OFF OFF
ON
OFF
OFF OFF OFF
66
OFF
ON
ON
OFF
27
ON
ON
OFF
OFF
ON
ON
OFF OFF OFF OFF
3
Installation
DIP switch position
ID
17
18
3
Installation
67
ON
68
69
ON
Installation
OFF OFF OFF OFF
ON
OFF
106
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF OFF
ON
OFF OFF OFF
ON
OFF
ON
OFF
ON
OFF OFF OFF
ON
OFF
107
ON
ON
OFF
ON
OFF
ON
ON
OFF
108
OFF OFF
ON
ON
OFF
ON
ON
OFF
70
OFF
ON
ON
OFF OFF OFF
ON
OFF
71
ON
ON
ON
OFF OFF OFF
ON
OFF
109
ON
OFF
ON
ON
OFF
ON
ON
OFF
110
OFF
ON
ON
ON
OFF
ON
ON
OFF
72
OFF OFF OFF
ON
OFF OFF
ON
OFF
73
ON
OFF OFF
ON
OFF OFF
ON
OFF
111
ON
ON
ON
ON
OFF
ON
ON
OFF
112
OFF OFF OFF OFF
ON
ON
ON
OFF
74
OFF
ON
OFF
ON
OFF OFF
ON
OFF
75
ON
ON
OFF
ON
OFF OFF
ON
OFF
113
ON
OFF OFF OFF
ON
ON
ON
OFF
114
OFF
ON
OFF OFF
ON
ON
ON
OFF
76
OFF OFF
ON
ON
OFF OFF
ON
OFF
77
ON
OFF
ON
ON
OFF OFF
ON
OFF
115
ON
ON
OFF OFF
ON
ON
ON
OFF
116
OFF OFF
ON
OFF
ON
ON
ON
78
OFF
ON
ON
ON
OFF OFF
ON
OFF
OFF
117
ON
OFF
ON
OFF
ON
ON
ON
OFF
79
ON
ON
ON
ON
OFF OFF
80
OFF OFF OFF OFF
ON
OFF
ON
OFF
118
OFF
ON
ON
OFF
ON
ON
ON
OFF
ON
OFF
119
ON
ON
ON
OFF
ON
ON
ON
OFF
81
ON
OFF OFF OFF
ON
82
OFF
ON
OFF OFF
ON
OFF
ON
OFF
120
OFF OFF OFF
ON
ON
ON
ON
OFF
OFF
ON
OFF
121
ON
OFF OFF
ON
ON
ON
ON
OFF
83
ON
ON
OFF OFF
84
OFF OFF
ON
OFF
ON
OFF
ON
OFF
122
OFF
ON
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
123
ON
ON
OFF
ON
ON
ON
ON
OFF
85
ON
OFF
ON
86
OFF
ON
ON
OFF
ON
OFF
ON
OFF
124
OFF OFF
ON
ON
ON
ON
ON
OFF
OFF
ON
OFF
ON
OFF
125
ON
OFF
ON
ON
ON
ON
ON
OFF
87
ON
ON
88
ON
OFF
ON
OFF
ON
OFF
126
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF OFF OFF
ON
ON
OFF
ON
OFF
127
ON
ON
ON
ON
ON
ON
ON
OFF
89
ON
90
OFF
OFF OFF
ON
ON
OFF
ON
OFF
128
OFF OFF OFF OFF OFF OFF OFF
ON
ON
OFF
ON
ON
OFF
ON
OFF
129
ON
OFF OFF OFF OFF OFF OFF
ON
91
ON
92
ON
OFF
ON
ON
OFF
ON
OFF
130
OFF
ON
OFF OFF OFF OFF OFF
ON
OFF OFF
ON
ON
ON
OFF
ON
OFF
131
ON
ON
OFF OFF OFF OFF OFF
ON
93
ON
94
OFF
OFF
ON
ON
ON
OFF
ON
OFF
132
OFF OFF
ON
OFF OFF OFF OFF
ON
ON
ON
ON
ON
OFF
ON
OFF
133
ON
OFF
ON
OFF OFF OFF OFF
95
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
134
OFF
ON
ON
OFF OFF OFF OFF
ON
96
OFF OFF OFF OFF OFF
ON
ON
OFF
135
ON
ON
ON
OFF OFF OFF OFF
ON
97
ON
OFF OFF OFF OFF
ON
ON
OFF
136
OFF OFF OFF
ON
OFF OFF OFF
ON
98
OFF
ON
OFF OFF OFF
ON
ON
OFF
137
ON
OFF OFF
ON
OFF OFF OFF
ON
99
ON
ON
OFF OFF OFF
ON
ON
OFF
138
OFF
ON
OFF
ON
OFF OFF OFF
ON
100
OFF OFF
ON
OFF OFF
ON
ON
OFF
139
ON
ON
OFF
ON
OFF OFF OFF
ON
101
ON
OFF
ON
OFF OFF
ON
ON
OFF
140
OFF OFF
ON
ON
OFF OFF OFF
ON
102
OFF
ON
ON
OFF OFF
ON
ON
OFF
141
ON
OFF
ON
ON
OFF OFF OFF
ON
103
ON
ON
ON
OFF OFF
ON
ON
OFF
142
OFF
ON
ON
ON
OFF OFF OFF
ON
104
OFF OFF OFF
ON
OFF
ON
ON
OFF
143
ON
ON
ON
ON
OFF OFF OFF
ON
105
ON
ON
OFF
ON
ON
OFF
144
OFF OFF OFF OFF
ON
ON
OFF OFF
OFF OFF
Installation
ON
OFF OFF OFF
ON
OFF OFF
ON
184
OFF OFF OFF
ON
ON
ON
OFF
ON
146
OFF
ON
OFF OFF
ON
OFF OFF
ON
147
ON
ON
OFF OFF
ON
OFF OFF
ON
185
ON
OFF OFF
ON
ON
ON
OFF
ON
186
OFF
ON
OFF
ON
ON
ON
OFF
ON
148
OFF OFF
ON
OFF
ON
OFF OFF
ON
149
ON
OFF
ON
OFF
ON
OFF OFF
ON
187
ON
ON
OFF
ON
ON
ON
OFF
ON
188
OFF OFF
ON
ON
ON
ON
OFF
ON
150
OFF
ON
ON
OFF
ON
OFF OFF
ON
151
ON
ON
ON
OFF
ON
OFF OFF
ON
189
ON
OFF
ON
ON
ON
ON
OFF
ON
190
OFF
ON
ON
ON
ON
ON
OFF
ON
152
OFF OFF OFF
ON
ON
OFF OFF
ON
153
ON
OFF OFF
ON
ON
OFF OFF
ON
191
ON
ON
ON
ON
ON
ON
OFF
ON
192
OFF OFF OFF OFF OFF OFF
ON
ON
154
OFF
ON
OFF
ON
ON
OFF OFF
ON
155
ON
ON
OFF
ON
ON
OFF OFF
ON
193
ON
OFF OFF OFF OFF OFF
ON
ON
194
OFF
ON
OFF OFF OFF OFF
ON
156
OFF OFF
ON
ON
ON
OFF OFF
ON
ON
195
ON
ON
OFF OFF OFF OFF
ON
ON
157
ON
OFF
ON
ON
ON
OFF OFF
ON
196
OFF OFF
ON
OFF OFF OFF
ON
ON
158
OFF
ON
ON
ON
ON
OFF OFF
ON
197
ON
OFF
ON
OFF OFF OFF
ON
ON
159
ON
ON
ON
ON
160
OFF OFF OFF OFF OFF
ON
OFF OFF
ON
198
OFF
ON
ON
OFF OFF OFF
ON
ON
ON
OFF
ON
199
ON
ON
ON
OFF OFF OFF
ON
ON
161
ON
162
OFF
OFF OFF OFF OFF
ON
OFF
ON
200
OFF OFF OFF
ON
OFF OFF
ON
ON
ON
OFF OFF OFF
ON
OFF
ON
201
ON
OFF OFF
ON
OFF OFF
ON
ON
163
ON
164
OFF OFF
ON
OFF OFF OFF
ON
OFF
ON
202
OFF
ON
OFF
ON
OFF OFF
ON
ON
ON
OFF OFF
ON
OFF
ON
203
ON
ON
OFF
ON
OFF OFF
ON
ON
165
ON
166
OFF
OFF
ON
OFF OFF
ON
OFF
ON
204
OFF OFF
ON
ON
OFF OFF
ON
ON
ON
ON
OFF OFF
ON
OFF
ON
205
ON
OFF
ON
ON
OFF OFF
ON
ON
167
ON
168
OFF OFF OFF
ON
ON
OFF OFF
ON
OFF
ON
206
OFF
ON
ON
ON
OFF OFF
ON
ON
ON
OFF
ON
OFF
ON
207
ON
ON
ON
ON
OFF OFF
ON
ON
169
ON
170
OFF
OFF OFF
ON
OFF
ON
OFF
ON
208
OFF OFF OFF OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
209
ON
OFF OFF OFF
ON
OFF
ON
ON
171
ON
172
ON
OFF
ON
OFF
ON
OFF
ON
210
OFF
ON
OFF OFF
ON
OFF
ON
ON
OFF OFF
ON
ON
OFF
ON
OFF
ON
211
ON
ON
OFF OFF
ON
OFF
ON
173
ON
ON
OFF
ON
ON
OFF
ON
OFF
ON
212
OFF OFF
ON
OFF
ON
OFF
ON
ON
174
175
OFF
ON
ON
ON
OFF
ON
OFF
ON
213
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
ON
OFF
ON
214
OFF
ON
ON
OFF
ON
OFF
ON
ON
176
OFF OFF OFF OFF
ON
ON
OFF
ON
215
ON
ON
ON
OFF
ON
OFF
ON
ON
177
ON
OFF OFF OFF
ON
ON
OFF
ON
216
OFF OFF OFF
ON
ON
OFF
ON
ON
178
OFF
ON
OFF OFF
ON
ON
OFF
ON
217
ON
OFF OFF
ON
ON
OFF
ON
ON
179
ON
ON
OFF OFF
ON
ON
OFF
ON
218
OFF
ON
OFF
ON
ON
OFF
ON
ON
180
OFF OFF
ON
OFF
ON
ON
OFF
ON
219
ON
ON
OFF
ON
ON
OFF
ON
ON
181
ON
OFF
ON
OFF
ON
ON
OFF
ON
220
OFF OFF
ON
ON
ON
OFF
ON
ON
182
OFF
ON
ON
OFF
ON
ON
OFF
ON
221
ON
OFF
ON
ON
ON
OFF
ON
ON
183
ON
ON
ON
OFF
ON
ON
OFF
ON
222
OFF
ON
ON
ON
ON
OFF
ON
ON
3
Installation
145
19
20
3
Installation
Installation
223
ON
ON
OFF
ON
ON
Removing the Protection Tape
224
OFF OFF OFF OFF OFF
ON
ON
ON
225
ON
OFF OFF OFF OFF
ON
ON
ON
226
OFF
ON
OFF OFF OFF
ON
ON
ON
You should remove the protection tape before installing
the camera.
Remove the protection tape carefully.
227
ON
ON
OFF OFF OFF
ON
ON
ON
228
OFF OFF
ON
OFF OFF
ON
ON
ON
229
ON
OFF
ON
OFF OFF
ON
ON
ON
230
OFF
ON
ON
OFF OFF
ON
ON
ON
231
ON
ON
ON
OFF OFF
ON
ON
ON
232
OFF OFF OFF
ON
OFF
ON
ON
ON
233
ON
OFF OFF
ON
OFF
ON
ON
ON
234
OFF
ON
OFF
ON
OFF
ON
ON
ON
235
ON
ON
OFF
ON
OFF
ON
ON
ON
236
OFF OFF
ON
ON
OFF
ON
ON
ON
237
ON
OFF
ON
ON
OFF
ON
ON
ON
238
OFF
ON
ON
ON
OFF
ON
ON
ON
239
ON
ON
ON
ON
OFF
ON
ON
ON
240
OFF OFF OFF OFF
ON
ON
ON
ON
241
ON
OFF OFF OFF
ON
ON
ON
ON
242
OFF
ON
OFF OFF
ON
ON
ON
ON
243
ON
ON
OFF OFF
ON
ON
ON
ON
244
OFF OFF
ON
OFF
ON
ON
ON
ON
245
ON
OFF
ON
OFF
ON
ON
ON
ON
246
OFF
ON
ON
OFF
ON
ON
ON
ON
247
ON
ON
ON
OFF
ON
ON
ON
ON
248
OFF OFF OFF
ON
ON
ON
ON
ON
249
ON
OFF OFF
ON
ON
ON
ON
ON
250
OFF
ON
OFF
ON
ON
ON
ON
ON
251
ON
ON
OFF
ON
ON
ON
ON
ON
252
OFF OFF
ON
ON
ON
ON
ON
ON
253
ON
OFF
ON
ON
ON
ON
ON
ON
254
OFF
ON
ON
ON
ON
ON
ON
ON
255
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
1. Loosen the screws using the wrench and remove the
dome cover.
2. Remove the protection tape and attach the dome
cover.
>>Caution
You must align the OPEN and LOCK mark correctly
when you turn the dome cover to open or close.
If you do not align the mark, it causes a malfunction.
Installation
Mounting the camera
21
3. Drill a hole on the wall where you want to install the
pipe. Pass the connection cable through the wall
mount assembly so that they hang down.
You can mount the camera on the ceiling or wall.
Wall mount (optional)
Install the camera by the following order.
1. Disassemble the PIPE Installation Bracket to remove the
[A] part.
[A]
4. Install the wall mount assembly.
3
Installation
2. Install the PIPE Installation Bracket to the Wall Mount
assembly.
22
Installation
5. Connect the connection cable and the safety cable to
the camera body.
3
Installation
6. Attach the camera to the camera assembly bracket by
following step a and b. Align the locking point of
the wall mount assembly and the camera.
7. Tighten the locking screw.
Installation
8. Assemble the camera cover as shown below.
23
Pendant mount (Optional)
Install the camera by the following order.
1. Disassemble the PIPE Installation Bracket to remove the
[A] part.
[A]
,,Note
You can install the PIPE Installation Bracket direct to
the other type LG Wall Mount assembly. This LG Wall
Mount assembly make to easy to install your camera.
3
Installation
2. Install the PIPE Installation Bracket to the Pendant
Mount assembly.
24
Installation
3. Drill a hole on the wall where you want to install the
pipe. Pass the connection cable through the pendant
mount assembly so that they hang down.
4. Install the pendant mount assembly.
3
Installation
5. Connect the connection cable and the safety cable to
the camera body.
Installation
6. Attach the camera to the camera assembly bracket by
following step a and b. Align the locking point of
the wall mount assembly and the camera.
25
7. Tighten the locking screw.
3
Installation
26
Installation
8. Assemble the camera cover as shown below.
,,Note
You can install the PIPE Installation Bracket direct to
the other type LG Wall Mount assembly. This LG Wall
Mount assembly make to easy to install your camera.
3
Installation
Operation
27
4
Operation
Setup Menu Overview
The following table shows the list of menu items and options. You can adapt the camera to your requirements by setting up
the respective items in these menus.
1st level
2nd level
FOCUS
CAMERA SET
Contents
FOCUS MODE
AUTO/MANUAL/ONE PUSH/ZOOM TRIG
FOCUS DIST
1 M, 3 M, 6 M
ZOOM START
x1 to x36
ZOOM END
x2 to x444
RETURN
-
IRIS
AUTO/MANUAL
AGC
OFF, 1 to 10
WDR/BLC
OFF/WDR/BLC/HSBLC
BRIGHTNESS
0 to 100
SHUTTER
OFF, A.FLK, 1/160, …, X2, AUTO
SENS-UP
AUTO X2/AUTO X3/…/AUTO X128/OFF
RETURN
-
ATW
-
AUTO
WHITE BALANCE
MANUAL
COLOR TEMP
INDOOR/OUTDOOR
RED
- 100 to +100
BLUE
- 100 to +100
RETURN
-
ONE PUSH
DAY/NIGHT
AUTO
DAY
4
Operation
EXPOSURE
3rd level
D/N LEVEL
LOW/MIDDLE/HIGH
DWELL TIME
5,10,15,30,60 SEC
RETURN
-
28
Operation
DAY/NIGHT
3D-DNR
CAMERA SET
COLOR
SHARPNESS
STABILIZER
NIGHT
-
OFF
-
LOW
-
MIDDLE
-
HIGH
-
ON
COLOR
-50 to 50
OFF
-
0 to 68
-
ON
-
OFF
-
RETURN
-
4
Operation
SET PRESET
PRESET
PAN/TILT SET
OFF/ON
SPEED
1 to 127
DWELL TIME
1 to 255
IRIS
AUTO, 20, 40, 60, 80, 100 %
WDR/BLC/HSBLC
OFF/ LOW WDR/ MID. WDR
HIGH WDR/ LOW BLC/ MID. BLC /
HIGH BLC/ LOW HSBLC /
MID. HSBLC/ HIGH HSBLC
SHUTTER
X512, ..., x2, AUTO, OFF, A.FLK,
1/160, ..., 1/120 000
SET POSITION
-
SAVE
-
RETURN
-
GOTO PRESET
0 to 255 (LCP3750 series)
0 to 239 (LCP3750T series)
PRESET TOUR
-
CLEAR PRESET
0 to 255 (LCP3750 series)
0 to 239 (LCP3750T series)
CLEAR ALL
-
FREEZE
GROUP TOUR
NAME
ON
OFF
RETURN
-
SET GROUP
1 to 10
RUN
1 to 10
CLEAR
1 to 10
RETURN
-
Operation
PATTERN
AUTO PAN
PRIVACY MASK
RECORD
1 to 4
RUN
1 to 4
RETURN
-
SET AUTO PAN
1 to 8
RUN
-
CLEAR
-
RETURN
-
MASK NUMBER
1 to 8
SET MASK
-
MASK STATE
ON/OFF
MASK COLOR
GRAY, WHITE, BLACK
WIDTH
0 to 320
HEIGHT
0 to 240
RETURN
-
PROPORTIONAL PT
ON/OFF
COMPASS
ON/OFF
4
GO
HOME POSITION
DWELL TIME
(INFINITE to 100 MIN)
RETURN
SPECIAL
AUTO RETURN
OFF
-
ON
RETURN TIME
(1 MIN to 100 MIN)
OFF
-
TILT LIMIT
MOTION DET
COMMUNICATION
AUTO TRACKING
(LCP3750T model
only)
ON/OFF
ON/OFF
SENSITIVITY(0 to 100)
PROTOCOL
LG MULTIX/ PELCO C/
PELCO D/ PELCO P
BAUDRATE
2 400/ 4 800/ 19 200/ 38 400/
9 600 BPS
SAVE & EXIT
-
TRACK MODE
PT/PTZ
TARGET SIZE
SMALL/MEDIUM/LARGE
CAMERA HEIGHT
2.5 / 5 / 8 / 10 / 15 / 20 / 30M
Operation
SET
PAN/TILT SET
ON
29
30
Operation
LOST MODE
PAN/TILT SET
AUTO TRACKING
(LCP3750T model
only)
ACTION
STAY / RETURN
TIME OUT
10 / 30 S / 1 / 2 / 3 / 4 / 5 MIN
RETURN
-
TRACK TIME
INFINITE / 10 / 30 S / 1 / 2 / 3 / 4 / 5 MIN
SENSITIVITY
LOW / MIDDLE / HIGH
RETURN
-
RETURN
OSD SET
-
USER TITLE
ON/OFF
-
ZOOM MAG
ON/OFF
-
FUNCTION
ON/OFF
-
DOME ID
ON/OFF
-
RETURN
-
LANGUAGE
The option depends on the model.
4
Operation
ALARM IN1 to
ALARM IN4
ALARM SET
ON
NORMAL
OPEN/CLOSE
ALARM IN1 to ALARM IN4
PRESET 0 to 255 (LCP3750 series)
PRESET 0 to 239 (LCP3750T series)
DWELL TIME
3 to 255
RETURN
-
OFF
ALARM OUT1 to
ALARM OUT2
ON
ALARM OUT1 to ALARM OUT2
ALARM IN1 to ALARM IN4,
MOTION DET
DWELL TIME
3 to 255
RETURN
-
OFF
RESET
RETURN
-
INFORMATION
-
INITIALIZATION
-
CAMERA RESET
-
FACTORY RESET
-
RETURN
-
,,Note
The ZOOM START, the ZOOM END and the CAMERA RESET option are supported LCP3750 series only.
Operation
Please Enter Camera ID
Target CAM ID : _
Menu navigation
2. Enter the connected camera ID to control the camera
connected to the LKD1000 controller directly and
then press ENTER. The camera control menu will be
displayed.
We use the LKD1000 controller in this manual to explain
the features of the LG Dome camera because of the
LKD1000’s ability to control all of the LG Dome camera’s
advanced features. (For detailed controller instructions,
refer to the LKD1000 Controller Manual.)
LKD1000 button
Camera OSD operation
Cam OSD button
Displays or removes the setup
menu.
ZOOM IN button
Use to move upper direction on
the menu screen.
ZOOM OUT button
Use to move lower direction on
the menu screen.
FOCUS NEAR button
Use for increase the value of the
option.
Use for decrease the value of the
option.
Open/Close(Enter)
buttons
Executes selections and displays
a submenu for an item with the
mark.
Accessing the camera setup menu
To access the setup menus using the keys on a LKD1000
controller, do the following:
1. Select CAM (Camera) icon in the main menu and
then press ENTER. The camera ID input menu will be
displayed.
CAM
PRESET
/CAM1
3. Press [Cam OSD] button to display the camera setup
menu.
At this point, you have access to the camera setup menu.
General operation
1. Use [In] or [Out] button to select an option then press
[Open] or [Close] button.
Submenu appears on the monitor.
2. Use [In] or [Out] button to select a submenu option.
3. Use [Near] or [Far] button to select a value.
4. Select [RETURN] option then press [Open] or [Close] to
return to the previous menu.
5. Press [Cam OSD] button to exit the setup menu.
4
Operation
FOCUS FAR button
Please
Please Enter
EnterCamera
CameraIDID
Target CAM
CAM ID
ID::__
Target
31
32
Operation
Camera menu settings
Focus setting
The camera adjusts the focus automatically by sensing the
center of the picture.
Focus Distance setting
Selects the minimum shooting distance for the focus.
Select [FOCUS DIST] option on the [FOCUS] menu, then
select a focus distance value.
Zoom Start setting (Optional)
You can set the zoom start position of the camera.
When the zoom function is operated, the zoom always
will start at the selected zoom start position.
Select [ZOOM START] option on the [FOCUS] menu,
then set a zoom start position. The Zoom Start option is
supported LCP3750 series only.
Zoom End setting (Optional)
.
4
You can set the zoom end position of the camera. If
you set the zoom end position, the zoom is operated
up to the selected zoom end position.
Select [ZOOM END] option on the [FOCUS] menu,
then set the zoom end position. The Zoom End option is
supported LCP3750 series only.
Operation
Exposure settings
Focus mode
Select [FOCUS MODE] option on the [FOCUS] menu, then
select the following mode.
•
AUTO: Auto-focus is activated automatically.
•
MANUAL: Focus is activated automatically after the
zoom movement is finished. If you want to control the
focus manually, press the FOCUS (NEAR or FAR) buttons
on the controller.
•
ONE PUSH: The focus is activated manually. If the
camera is received auto-focus command, the camera
is activated auto-focus mode and the focus is set
automatically and then the focus mode is automatically
changed to manual mode.
•
ZOOM TRIG: The focus is activated manually. If you
change the zoom, the focus is activated automatically
and then the focus mode is automatically changed to
manual mode.
.
Iris setting
Select the desired lens iris value for camera exposure.
Select [IRIS] option on the [EXPOSURE] menu, then select a
value.
Operation
•
AUTO: The lens iris is set automatically.
•
MANUAL: Use [Near] or [Far] button to select the DC Iris
level. DC Iris level are set by one parameter unit.
SHUTTER (Shutter Speed) setting
Select the desired shutter speed for camera exposure. You
can change the shutter speed to higher speed to capture
fast-moving subjects, though the image becomes darker.
AGC (Automatic Gain Control) setting
1. Select [SHUTTER] option on the [EXPOSURE] menu.
If the images are too dark, change the maximum [AGC]
value to make the images bright.
2. Use [Near] or [Far] button to set shutter speed.
1. Select [AGC] option on the [EXPOSURE] menu.
SENS-UP setting
2. Use [Near] or [Far] button to select a mode.
If pictures are not clear due to darkness, use this function
to increase the sensitivity of picture.
WDR/BLC setting
1. Select [SENS-UP] option on the [EXPOSURE] menu.
Use WDR/BLC option to set the options for BLC or WDR
camera.
1. Select [WDR/BLC] option on the [EXPOSURE] menu.
2. Use [Near] or [Far] button to select a mode then press
[Open] or [Close].
•
•
BLC LEVEL: Camera’s backlight compensation
feature helps alleviate issues of visibility in high
contrast areas. Set the BLC level (LOW, MIDDLE,
HIGH).
•
HSBLC: Use for masking brightness of the specific
area to view the subject more clearly.
•
--
HSBLC LEVEL: Select the HSBLC level. (LOW,
MIDDLE, HIGH).
--
COLOR: Use [Near] or [Far] button to select a
color.
OFF: Not used.
BRIGHTNESS setting
You can increase the brightness of the darkened video.
If you set the brightness to lower value, the image is
darkened. If you set the brightness to higher value, the
image gets bright.
1. Select [BRIGHTNESS] option on the [EXPOSURE] menu.
2. Use [Near] or [Far] button to set the bright level.
2. Use [Near] or [Far] button to set the SENS-UP limit. To
set the SENS-UP function, select the [AUTO] on the
[SHUTTER].
,,Note
If you set the AGC to [OFF] or the SHUTTER is set to
one of the SHUTTER options except AUTO on the
[EXPOSURE] menu, the AUTO mode of the DAY/NIGHT
function is not available and [---] mark is displayed.
White Balance setting
Select the method by which the camera shifts its output
colors to compensate for the color of a light source.
1. Select [WHITE BALANCE] option on the [CAMERA SET]
menu.
2. Use [Near] or [Far] button to select a mode then press
[Open] or [Close].
•
ATW (Auto-Tracing White Balance): In this mode,
the color temperature range for the proper white
balance is approximately from 1700 K to 11 000 K.
Proper white balance may not be obtained under
the following conditions:
--
When the color temperature is out of the
1700 K to 11 000 K range.
4
Operation
WDR LEVEL: WDR (Wide dynamic range) feature
can be very helpful to cope with very challenging
lighting conditions. It is capable of capturing both
of the dark part and bright part and combining
the differences into a scene to generate a highly
realistic image as original scene. Set the WDR level
(LOW, MIDDLE, HIGH).
33
34
Operation
•
•
--
When the scene mostly contains high color
temperature objects, such as a blue sky or
sunset.
--
When the scene is dim.
When the color temperature is out of the
3 500 K to 6 500 K range.
--
When the scene mostly contains high color
temperature objects, such as a blue sky or sun
set.
--
When the scene is dim.
MANUAL: You can set the white balance options
manually.
--
4
Operation
•
--
DWELL TIME: Use [Near] or [Far] button to select
a dwell time.
If you set the AGC to [OFF] or the SHUTTER is set to
one of the SHUTTER options except AUTO on the
[EXPOSURE] menu, the AUTO mode of the DAY/NIGHT
function is not available and [---] mark is displayed.
•
DAY: Color mode enabled.
•
NIGHT: Black-and-white mode enabled.
3D-DNR setting
COLOR TEMP: Use [Near] or [Far] button to
select a function.
››
INDOOR: The color temperature range for
the proper white balance is approximately
3 600 K.
››
OUTDOOR: The color temperature range for
the proper white balance is approximately
6 500 K.
--
RED: Set the desired red value. (-100 to 100)
--
BLUE: Set the desired blue value. (-100 to 100)
ONE PUSH: If you select the ONE PUSH mode,
you will be able to set up the White Balance
automatically using [Open] or [Close] button.
Day/Night setting
1. Select [DAY/NIGHT] option on the [CAMERA SET]
menu.
2. Use [Near] or [Far] button to select the mode.
•
D/N LEVEL: Use [Near] or [Far] button to select a
level.
,,Note
AUTO: In this mode, the color temperature range
for the proper white balance is approximately
3 500 K to 6 500 K. Proper white balance may not
be obtained under the following conditions:
--
--
AUTO: You will be able to change the Day/Night
mode automatically.
1. Select [3D-DNR] option. If pictures are not clear due
to brightness, use this function to reduce the noise of
picture.
2. Use [Near] or [Far] button to select a option.
•
•
,,Note
If you set the AGC to [OFF] on the [EXPOSURE]
menu, the [3D-DNR] function is not available.
When you use this function, the afterimage may
occur.
Operation
35
Color setting
You can switch the displayed picture to grayscale or color.
1. Select [STABILIZER] option on the [CAMERA SET] menu.
2. Use [Near] or [Far] button to ser it [ON] or [OFF].
1. Select [COLOR] option on the [CAMERA SET] menu.
2. Use [Near] or [Far] button to change a color effect.
•
ON: To display the picture with color. Select ON and
press [Open] or [Close] to display the submenu. You
can adjust the color level using the [Near] or [Far]
button.
•
OFF: To display the picture with grayscale.
Sharpens the image outline.
1. Select [SHARPNESS] option on the [CAMERA SET]
menu.
2. Use [Near] or [Far] button to adjust the option. If you
set the sharpness value to higher, the image outline
becomes sharp. If you set to lower value, the image
outline becomes dim.
Stabilizer setting
The image stabilizer function minimizes the appearance
of shaky images caused by low-frequency vibration.
This function is useful for outdoor surveillance.
Preset setting
Preset position is the function to register camera
monitoring positions (preset positions) associated with
position numbers. By entering the position numbers, you
can move cameras to the preset positions.
.
4
Operation
Sharpness setting
PAN/TILT Settings
36
Operation
To register preset positions
1. Select the [SET PRESET] option on the [PRESET] menu.
2. Use the [Near] or [Far] button to select the preset
number you wish to register and press the [Open] or
[Close] button.
3. Set the preset name.
How to set the preset name.
1. Set the NAME option to [ON] and press [Open] or
[Close] button.
2. Use [In], [Out], [Near] or [Far] button to select a
character, number, symbol mark or option item.
4
•
</>: Moves cursor to left or right.
•
(Blank): Insert a space at the cursor position.
•
CLR: If you enter the wrong code, select [CLR]
then press [Open] or [Close] to delete. All letters
will be erased at once.
•
SAVE: Select this option to confirm the settings.
•
EXIT: Select this option to exit the settings.
Operation
3. Press [Open] or [Close] button to confirm your
selection.
4. Select the speed to move to the preset position.
5. Select the preset tour dwell time.
6. Set the IRIS option. IRIS LEVEL are set by 20 % unit
(20 %, 40 %, 60 %, 80 %, 100 %)
7. Set the WDR/BLC/HSBLC option.
8. Set the SHUTTER option.
9. Select the [SET POSITION] option and press [Open] or
[Close] button.
10. Move the camera to a point you wish by using the
joystick and then press [Open] or [Close] button to save
it.
11. Select [SAVE] option and press [Open] or [Close] button
to confirm the settings.
The position and its number are memorized.
12. Repeat steps 1 to 11 to add additional positions.
13. Select [RETURN] option and press [Open] or [Close]
button to exit the setting menu.
Changing a picture in a preset position
The preset function makes the combination camera
move to the programmed preset position. It is necessary
to program preset positions for the combination camera
beforehand.
1. Select [GOTO PRESET] option on the [PRESET] menu.
2. Select the memorized preset position’s index number
then press [Open] or [Close] button. The camera moves
to the preset position and the picture of the camera in
that position appears on the monitor.
To tour the preset positions
You can tour all preset positions.
1. Select [PRESET TOUR] option on the [PRESET] menu.
All registered preset positions in the camera will
be selected and the camera position image will be
switched on the active monitor.
2. You can stop the tour by moving the joystick or
sending Stop Tour commands .
To clear the preset position
You can clear a memorized preset position.
1. Select [CLEAR PRESET] option on the [PRESET] menu.
2. Selects the memorized preset index number then press
[Open] or [Close] button to clear the preset positions.
To clear all the preset positions
You can clear all of the memorized preset positions at once.
1. Select [CLEAR ALL] option on the [PRESET] menu.
2. Press [Open] or [Close] button to clear the all preset
positions.
Freeze function
1. Select [FREEZE] option on the [PRESET] menu.
2. Use [Near] or [Far] button to set up the [ON] or [OFF].
Operation
Group tour setting
To delete a group
You can create a group using preset positions that are
registered already. A maximum of 10 groups is available.
1. Select [CLEAR] option on the [GROUP TOUR] menu.
37
You can delete a memorized group.
2. Select the group number and press [Open] or [Close]
button. The group will be deleted.
Pattern setting
You can activate the camera in a repeating pattern. The
pattern is programmed by recording your manual pan, tilt,
and zoom operations. The camera stores the movements
you performed in memory.
.
4
To set the group
1. Select [SET GROUP] option on the [GROUP TOUR]
menu.
2. Select the group number and press [Open] or [Close]
button.
3. Set the group item. You can set the group item up to 8.
4. Select [SAVE] option and press [Open] or [Close] button
to confirm the settings.
5. Select [RETURN] option and press [Open] or [Close]
button to exit the setting menu.
To record the pattern
1. Select [RECORD] option on the [PATTERN] menu.
To tour the group
You can tour the group that is registered already.
2. Select the recording number and press [Open] or
[Close] button. The pattern recording is started
1. Select [RUN] option on the [GROUP TOUR] menu.
3. Move the camera through the desired movement.
2. Select the group number and press [Open] or [Close]
button.
The camera moves to the preset position in the group
and the picture of the camera in that position appears
on the monitor.
4. Press [Open] or [Close] button to stop the pattern
recording.
,,Note
The available total time of pattern differs depending
on operation.
Operation
.
38
Operation
To play the pattern
8. Repeat steps 1 to 7 to add additional positions.
1. Select [RUN] option on the [PATTERN] menu.
9. Select [RETURN] option and press [Open] or [Close]
button to exit the setting menu.
2. Select the recording number and then press [Open] or
[Close] button to play the programmed pattern. The
tour will play indefinitely until you stop it by moving
the joystick or pressing any button.
,,Note
If you press the [CLEAR] Option during the Auto
paning, All of AUTO PAN position will be deleted.
Auto Pan setting
To play the auto pan
By selecting the Auto Pan number, the camera pans
automatically.
You can play the camera with auto pan function.
1. Select [RUN] option on the [AUTO PAN] menu.
2. You can stop the Auto pan function by moving the
joystick or pressing any button.
To delete the auto pan position
You can delete the memorized auto pan position.
1. Select [AUTO PAN] option on the [PAN/TILT] menu.
2. Select [CLEAR] option then press [Open] or [Close]
button to delete the Auto pan position.
4
Operation
.
Privacy Mask setting
This function is aiming at the protection of personal
privacy, the mask zone is not displayed on the screen. Up
to 8 zones can be registered.
To set the Auto Pan position
1. Select [SET AUTO PAN] option on the [AUTO PAN]
menu.
2. Select the number you wish to register and press
[Open] or [Close] button.
3. Select the moving speed.
4. Select the Auto pan dwell time.
5. Move the camera to the desired start point by using
the joystick.
6. Select the [SET POSITION] option and press [Open] or
[Close] button.
7. Move the camera to the desired end point by using the
joystick and then press [Open] or [Close] button.
.
Operation
1. Select [PRIVACY MASK] option on the [PAN/TILT MENU].
2. Press [Open] or [Close] button to display the PRIVACY
MASK MENU.
39
Special setting
3. Use [Near] or [Far] button to select a zone number on
the [MASK NUMBER] option.
4. Select the [SET MASK] option and press [Open] or
[Close] button.
5. Select the mask zone using the joystick and then press
[Open] or [Close] button to save it.
6. Use [Near] or [Far] button to set up the [ON] or [OFF] on
the [MASK STATE] option. If you already registered the
mask zone and set to ON, the mask zone box appears
on the monitor.
.
7. Use [Near] or [Far] button to select the color of the
mask zone box on the [MASK COLOR] option.
8. Select the [WIDTH] option and use [Near] or [Far]
button to adjust the horizontal size of the mask zone
box.
9. Select the [HEIGHT] option and use [Near] or [Far]
button to adjust the vertical size of the mask zone box.
4
Operation
10. Repeat steps 3 to 9 to add additional positions.
•
•
•
,,Note
The parts with the registered mask numbers from
1 to 4 have the same color. (So do the parts with
the numbers from 5 to 8). If you change the mask
color, the registered mask color will be changed
automatically with the same color for each of
group (1 to 4, 5 to 8).
The initial PRIVACY MASK color is set to blue . After
setting, the PRIVACY MASK position on [SET MASK]
option, it`ll be changed to gray color.
Be sure, you have to press [Open] or [Close] button
on the [SET MASK] option to confirm the privacy
mask color.
If you need a Privacy Mask for a Preset, set the
Privacy Mask first.
Proportional PT
This function optimizes the image by automatically
adjusting the PAN/TILT (horizontal/vertical rotation) speed
according to the zoom ratio.
1. Select [PROPORTIONAL PT] option on the [SPECIAL]
menu.
2. Use [Near] or [Far] button to toggle it on and off.
•
ON : Pan/tilt speed is in inverse proportion to the
zoom ratio.
•
OFF : The speed is constant at the fastest level
regardless of the zoom ratio.
Compass
You can display the north, south, east and west information
on the screen.
1. Select [COMPASS] option on the [SPECIAL] menu.
2. Set the [COMPASS] option to [SET] and then press
[Open] or [Close] button.
3. Select north point using the joystick and then press
[Open] or [Close] button.
4. Set the [COMPASS] option to [ON].
40
Operation
Home position
Tilt limit
Use the following procedure to make the home position.
1. Select [TILT LIMIT] option on the [SPECIAL] menu.
1. Select [HOME POSITION] option on the [SPECIAL]
menu.
2. Use [Near] or [Far] button to set it [ON]. If you do not
want to use this function, set it to [OFF].
The home position is the camera’s basic position.
The camera returns to this position whenever you want.
2. Use [Near] or [Far] button to set it ON.
3. Press [Open] or [Close] button.
4. Select [SET] option and then press [Open] or [Close]
button.
5. Select the home position where you want and then
press [Open] or [Close] button.
6. Select [DWELL TIME] option and then select the dwell
time.
7. Select [RETURN] option and press [Open] or [Close]
button to exit the setting menu.
Go to Home position
4
1. Select [HOME POSITION] option on the [SPECIAL]
menu.
Operation
2. Use [Near] or [Far] button to set it ON.
3. Press [Open] or [Close] button.
4. Select [GO] option and then press [Open] or [Close]
button. The camera will move to the home position.
Auto return
This function can be used to specify automatic return to a
particular mode if a certain amount of time elapses without
any operation being performed.
You can specify the tilt range. If you set this function, the
camera is able to tilt from 10º to 170º.
,,Note
The top side of screen may be hidden by tilting range.
Motion Detection
The motion detection detects the moving objects in the
scene by monitoring changes in brightness level.
1. Select [MOTION DET] option on the [SPECIAL] menu.
2. Use [Near] or [Far] button to set it [ON]. If you do not
want to use this function, set it to [OFF].
3. Press [Open] or [Close] button.
4. Use [Near] or [Far] button to set the [SENSITIVITY]
option.
Communication
This setting is required to establish a connection between
the system controller and the camera.
1. Select [COMMUNICATION] option on the [SPECIAL]
menu.
2. Press [Open] or [Close] button.
3. Set the below options.
•
PROTOCOL: This item lets you set a protocol for RS485 communication. Select the desired protocol.
•
BAUDRATE: Select the desired speed of
communication between the system controller
and the camera. Confirm selected parameter to the
baud rate of the system controller.
•
SAVE & EXIT: Select this option and then
press [Open] or [Close] button to save the
communication settings and exit the setting menu.
1. Select [AUTO RETURN] option on the [SPECIAL] menu.
2. Use [Near] or [Far] button to set it [ON] and then press
[Open] or [Close] button.
3. Select [RETURN TIME] option and then select the auto
return time.
4. Select [RETURN] option and press [Open] or [Close]
button to exit the setting menu.
Operation
Auto Tracking setting (Optional)
,,Note
The Auto Tracking option is supported LCP3750T series
only.
Configure Auto Tracking MENU options. These options are
used for tracking the displayed object in motion on the
screen. If you want to use the [Auto Tracking] option, use
[Near] or [Far] button to set it ON.
,,Note
Environmental conditions
In the case of following installation conditions, object
tracking errors may occur.
•
Contrast between object and background is low.
•
Dome cover is contaminated by raindrops or snow
etc.
•
Illumination is changing dynamically.
•
There are a lot of movement except tracking
object.
•
An object moves vertically on the optic angle of
the camera.
•
An object moves under an installed camera.
•
An object that there are a lot of changes of light
levels, e.g. shining or flickering.
•
Environment that reflection is on dome inside
by window reflection, road surface reflection,
backlight.
•
Object moves behind large and tall objects, e.g.
telegraph pole etc.
•
The motion of object is fast.
•
Occasion that camera is vibrating.
Track Mode
Use [Near] or [Far] button to select a mode.
•
PT : This mode uses Pan/Tilt and tracks an object
while Auto Tracking is conducted.
•
PTZ : This mode uses Pan/Tilt/Zoom and tracks an
object while Auto Tracking is conducted.
Target Size
Configuration of how large the object being tracked is
actually displayed on the screen.
•
SMALL : This mode zooms in and magnifies the
object until it occupies a quarter size of the screen.
•
MEDIUM : This mode zooms in and magnifies the
object until it occupies a half size of the screen.
•
LARGE: This mode zooms in and magnifies the
object until it occupies three-fourths of the screen.
,,Note
If you set the [TRACK MODE] to PT, you can not set the
[TARGET SIZE] and [---] is displayed.
4
Operation
.
41
42
Operation
Camera Height
Use [Near] or [Far] button to select how high the camera is
installed.
Lost Mode
You can configure what the camera will execute when the
camera loses the object.
•
--
4
STAY : When the camera loses the object, it
doesn’t come back to its initial position, but
stays where the object has been just lost.
RETURN : When the camera loses the object, it
returns to its initial position and gets ready to
detect a new object.
TIME OUT : When the camera loses the object for
the first time, it zooms out twice and tries to track
the object. You can configure that after the camera
zooms out twice, how long the camera maintains
the status of the object detection to re-detect it.
Operation
Track Time
You can configure maximum time duration of tracking. The
system starts tracking when it detects objects in motion. As
the time reaches the maximum time duration configured
by user, the tracking is disabled and the camera returns
to its initial position. The system will be reset for tracking
new objects. You should be aware not to set up the time
duration too short since it may cause tracking failure.
•
LOW : The sensitivity of the object detection is low.
In this case, if the object is too small or very similar
to the background, it may not be detected.
•
MEDIUM : The sensitivity of the object detection
is middle. The camera detects the object more
accurately than the case of low sensitivity. It
may detect swaying branches or flags, but not
frequently.
•
HIGH : The sensitivity of the object detection is
high. The camera can detect a small object, but it
can also detect swaying branches or flags, rain or
snow.
Under low light circumstances, tracking function
may not work.
Tracking error may occur by the headlight of
vehicle.
•
Auto PTZ tracking is used by single intruder watch
of access limitation area. Therefore, when there are
many moving objects, it may not be suitable to
use.
•
Tracking errors may occur in case of camera was
not fixed well.
•
To the time when the long shadow occurs in
sunrise and sunset etc, tracking errors will be able
to occur.
•
Under flickering lights or dome internal reflections,
tracking function may not work correctly.
•
Object tracking may malfunction about object
passed very fast.
•
When contrast between object and background is
low, tracking fail may occur.
•
If tracking object is so big or small, tracking fail may
occur.
•
The camera may detect and track unintended
movements – tree branches, hanging banner, flag,
color change by sudden lighting change, luminous
intensity change by cloud – tracking errors can be
occurred by bright light sources, flickering lights
and dome internal reflections. To prevent and
correct such errors, adjust the direction and angle
of the camera.
•
Tracking errors and degradation by raindrops,
snow, fog, smoke or heat can be occurred.
•
If the camera lens is smeared with foreign
substances or is scratched, tracking errors may
occur.
•
Adjust the tracking object size to 1/4 of screen at
initial position.
•
Smeared and dusty dome covers can decrease the
tracking performance so it is necessary to clean the
dome cover and camera lens regularly.
•
This feature may not perform as expected
depending on the situation and circumstance.
Sensitivity
You can configure the sensitivity of detection. Choosing
proper sensitivity will enhance the performance of the
Auto Tracking since the environmental condition may
influence the accuracy of the detection. For instance, rain,
snow, or swaying branches may cause malfunction of auto
tracking.
,,Note
•
ACTION
--
•
•
Operation
OSD Settings
•
CLR: If you enter the wrong code, select [CLR] then
press [Open] or [Close]. All letters will be erased at
once.
•
POS: Move the USER TITLE position on the screen
using the [Near] or [Far] buttons.
•
END: Select this option to exit the settings.
43
ZOOM MAG setting
Displays or removes the zoom OSD on the screen.
.
1. Select [ZOOM MAG] option on the [OSD] menu.
3. Select [RETURN] option and press [Open] or [Close]
button to exit the setting menu.
User title setting
You can use the camera identification to assign a number
and character to the camera.
FUNCTION setting
Displays or removes the Function OSD on the screen.
1. Select [USER TITLE] option on the [OSD] menu.
2. Use [Near] or [Far] button to set it [ON].
3. Press [Open] or [Close] button. The USER TITLE menu
appears.
4. Use [In], [Out], [Near] or [Far] button to select a
character, number, symbol mark or option item.
1. Select [FUNCTION] option on the [OSD] menu.
2. Use [Near] or [Far] button to set it [ON] or [OFF].
A
•
</>: Moves cursor to left or right.
•
A (Blank): Insert a space at the cursor position.
3. Select [RETURN] option and press [Open] or [Close]
button to exit the setting menu.
Operation
2. Use [Near] or [Far] button to set it [ON] or [OFF].
4
44
Operation
DOME ID setting
Displays or removes the Camera ID OSD on the screen.
ALARM Setting
This camera has a terminal that can sense the alarm signals.
The camera can be programmed to go to a preset with a
signal from any connected alarm device.
1. Select [DOME ID] option on the [OSD] menu.
2. Use [Near] or [Far] button to set it [ON] or [OFF]
3. Select [RETURN] option and press [Open] or [Close]
button to exit the setting menu.
4
LANGUAGE Setting
Operation
Select a language for the setup menu and OSD display.
.
Alarm In setting
1. Select one of the alarms in option on the [ALARM SET]
menu.
2. Use [Near] or [Far] button to set it [ON].
3. Press [Open] or [Close] button.
4. Select [NORMAL] option and select [Open] or [Close]
option.
•
OPEN: Activate the alarm in the close position.
•
CLOSE: Activate the alarm in the open position.
5. Select [ALARM IN(1 to 4)] option and select preset
number. When the alarm is triggered, the camera
moves to the selected preset position. The presets run
continuously until alarm source is off.
6. Select [DWELL TIME] option and then set the alarm
dwell time. The alarm is stopped after selected dwell
time.
Operation
Alarm Out setting
Initialization
1. Select one of the alarm out options on the [ALARM
SET] menu.
You can initialize the camera settings.
2. Use [Near] or [Far] button to set it [ON].
2. Press [Open] or [Close] button then confirmation
window is displayed.
3. Press [Open] or [Close] button.
4. Select alarm input number or motion detection. When
the selected alarm input is triggered or motion is
detected, the alarm signal is outputted.
5. Select [DWELL TIME] option and then set the alarm
dwell time. The alarm output is stopped after selected
dwell time.
45
1. Select [INITIALIZATION] option on the [RESET] menu.
3. Select [YES] and press [Open] or [Close] button.
Camera reset (Optional)
Clear certain settings and information of the [CAMERA SET
MENU] and return to factory default settings. The Camera
Reset option is supported LCP3750 series only.
1. Select [CAMERA RESET] option on the [RESET] menu.
RESET Setting
2. Press [Open] or [Close] button then confirmation
window is displayed.
3. Select [YES] and press [Open] or [Close] button.
Factory reset
1. Select [FACTORY RESET] option on the [RESET] menu.
2. Press [Open] or [Close] button then confirmation
window is displayed.
3. Select [YES] and press [Open] or [Close] button.The
camera will return to the factory default settings.
.
Information
You can view the current camera information such as PTZ
software version, camera software version, camera ID,
Protocol and Baud Rate.
1. Select [INFORMATION] option on the [RESET] menu.
2. Press [Open] or [Close] button to display the current
camera information.
4
Operation
Clear certain settings and information and return to factory
default settings.
46
Appendix
5
Appendix
Specifications
Model
LCP3750-AN
LCP3750-AP
LCP3750T-AN
LCP3750T-AP
Signal System
NTSC
PAL
NTSC
PAL
Image Sensor
4.5 mm(1/4 Type) Super HAD II CCD
Total Pixels Number
520 000 Pixels
610 000 Pixels
520 000 Pixels
610 000 Pixels
Effective Pixels Number
490 000 Pixels
570 000 Pixels
490 000 Pixels
570 000 Pixels
Horizontal Resolution
600 TV Lines
Lens
x37 Zoom, F1.5 (Wide End), F4.1(Tele End), f= 3.5 mm to 129 mm
S/N Ratio
50 dB (AGC Off )
Day/Night
AUTO / DAY / NIGHT
5
Appendix
Minimum
Illumination
(30 IRE)
B/W
0.01 lx (Sens-up Off ), 0.000 01 lx (Sens-up On)
Color
0.2 lx (Sens-up Off ), 0.003 lx (Sens-up On)
Optical Zoom
x37
Digital Zoom
x12
Scanning Frequency (H/V)
15.734 KHz /
59.94 Hz
15.625 KHz /
50 Hz
15.734 KHz /
59.94 Hz
Sync System
Internal
White Balance
ATW / AUTO / MANUAL / ONE PUSH
Control method
RS-485, Coaxial
Alarm Input
4 Channel
Alarm Output
2 Channel
15.625 KHz /
50 Hz
Appendix
Video Output
1Vp-p Composite (75Ω)
Backlight Compensation
WDR / BLC / HSBLC / OFF
Electric Shutter
1/60 to 1/120 000
1/50 to 1/120 000
1/60 to 1/120 000
3D-DNR
OFF / LOW / MIDDLE / HIGH
Auto Gain Control
ON / OFF
Digital Effect
Auto Flip
Pattern Recording & Play
1 to 4 / 1 to 4
Protection
Vandal Proof / IP66
Sens-Up
OFF / AUTO / MANUAL
Iris Control
AUTO / MANUAL
Stabilizer
ON / OFF
Motion Detection
Support
Auto Tracking
Not Support
1/50 to 1/120 000
Support
0 ˚ to 360 ˚, Maximum 500 ˚/Second
Tilting Range & Speed
0 ˚ to 180 ˚, Maximum 500 ˚/Second
Privacy Zone
8 Mask Zones
Preset/ID
256 Position (LCP3750 series), 240 Position (LCP3750T series) / 256
Auto Panning
2 to 8 points
Pattern
4
Group Touring
Maximum 10 Groups
Protocol
Coax : Pelco-C (Coaxial)
RS-485 : LG Multix, Pelco(D/P)
Operating Temperature/Humidity
-20 ˚C to 50 ˚C / 0 % RH to 80 % RH
Safekeeping Temperature/Humidity
-30 ˚C to 60 ˚C / 0 % RH to 90 % RH
Power Source
AC 24 V
22 W / 1.5 A
Dimension (Ø xH)
Weight
22 W / 1.8 A
234.6 mm x 269.9 mm
4.07 kg
4.17 kg
5
Appendix
Panning Range & Speed
Power Consumption / Input Current
47
AB28
Download PDF