OWNER'S MANUAL
Color Video Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
LCV5100-BN
LCV5100-BP
1205(V1.0)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle is
intended to alert the user to the presence
of uninsulated dangerous voltage within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
2
FCC WARNING: This equipment may generate or use
radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the
modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is
made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
•
A suitable conduit entries, knock-outs or glands shall
be provided in the cable entries of this product in the
end user.
•
Caution: Danger of explosion if battery is incorrectly
replaced. Replaced only with the same or equivalent
type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s
instructions.
•
Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall be
provided with brushings.
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
Warning: Do not install this equipment in a confined space
such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the
National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
Warning: If the product has no video out or sound, please
stop using. Unplug the power cable immediately and
contact the service center. (This may cause fire or electric
shock.)
Caution: This installation should be made by a qualified
service person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
Caution: Prevent the power cable from being severely bent
or having pressure exerted on it by a heavy object.
To disconnect power from mains, pull out the mains
cord plug. When installing the product, ensure that the
plug is easily accessible.
Warning: To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
Warning: The product has been dropped or the case is
broken, turn off the power and unplug the power cord.
(This may cause fire, electric shock, or injury.)
3
Disposal of your old appliance
1.
When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by the
European Directive 2002/96/EC.
2.
All electrical and electronic products
should be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or the
local authorities.
3.
The correct disposal of your old
appliance will help prevent potential
negative consequences for the
environment and human health.
4.
For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you
purchased the product.
EEE Compliance with Directive. (for Turkey only)
4
LG Electronics hereby declares that this/
these product(s) is/are in compliance
with the essential requirements and other
relevant provisions of Directive 2004/108/
EC, 2006/95/EC, and 2009/125/EC.
European Standards Centre:
Krijgsman 1, 1186 DM Amstelveen The
Netherlands
Important Safety Instructions
1.
Read these instructions.
and the point where they exit from the apparatus.
2.
Keep these instructions.
3.
Heed all warnings.
11. Only use attachments/accessories specified by the
manufacturer.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
5
Cautions for Safe Operation
Power Supply
Operating and storage location
This camera must always be operated a AC 24 V or DC 12 V
Certified/Listed, class 2 power supply only.
Avoid viewing a very bright object (such as light fittings)
during an extended period. Avoid operating or storing the
unit in the following locations.
Handling of the unit
Be careful not to spill water or other liquids on the unit. Be
cautions not to get combustible or metallic material inside
the body. If used with foreign matter inside, the camera is
liable to fail or to get cause of fire or electric shock.
•
Remove dust or dirt on the surface of the lens with a
blower.
•
Use a dry soft cloth to clean the body. If it is very dirty,
use a cloth dampened with a small quantity of neutral
detergent then wipe dry.
•
Avoid the use of volatile solvents such as thinners,
alcohol, benzene and insecticides. They may damage
the surface finish and/or impair the operation of the
camera.
6
•
Extremely hot or cold places (operating temperature
-10 °C to 50 °C, however, we recommend that the unit
be used within a temperature range of 0 °C to 45 °C)
•
Damp or dust place
•
Places exposed to rain
•
Places subject to strong vibration
•
Close to generators of powerful electromagnetic
radiation such as radio or TV transmitters.
Contents
Features.............................................................................. 8
Specification.................................................................... 35
Accessories................................................................................... 8
Part Names and Functions................................................ 9
Connections..................................................................... 10
Basic connection......................................................................10
Installation....................................................................... 11
Mounting the Camera............................................................11
Image Adjustment..................................................................14
Menu Operation.............................................................. 17
General Operation...................................................................20
Exposure Settings....................................................................21
White Balance settings..........................................................24
Day/Night Setting...................................................................25
Motion Detection Setting.....................................................26
3D-DNR Setting........................................................................27
Privacy Mask Setting..............................................................28
Special Menu Settings...........................................................30
SYSTEM Setting........................................................................34
7
MEZ62687703
SELFTAPPING SCREW
4 Place
PRODUCT CENTER POSITION
Features
This Color Video Camera is designed for installation in a
video surveillance system.
This manual contains instructions on how to install and
manage the Color Video Camera in your video surveillance
system.
Should you require any technical assistance, please contact
authorized service center.
•
High resolution and high sensitivity with a 6 mm (1/3
Type) Exview HAD CCD II.
•
Automatically switch between DC 12 V and AC 24 V.
•
Smart motion detector.
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
Accessories
FRONT
MEZ62687703
SELFTAPPING SCREW
4 Place
PRODUCT CENTER POSITION
Installation sticker
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
Wrench
M4 Fixing screws
8
n
Part Names and Functions
a Dome Cover
b Lens Cover
c Focus lock lever
a
Fixes the focus position after adjusting.
d Zoom lock lever
Fixes the zoom position after adjusting.
b
c
d
e
f
g
h
i
j
k
e Azimuth adjuster
f Tilting lock screw
Fixes the tilting position after adjusting.
g Pan adjuster
h Setup menu control buttons
i Video Out connector
Use this jack for checking the picture with portable
monitor when install the camera.
j Power input connector
Supplies AC 24 V or DC 12 V from an external power
source.
k Video output connector (BNC type)
9
Connections
Basic connection
The peripheral devices (DVR, monitor, etc.), AC/DC adapter
and cables are not supplied.
1. Make the video signal connection between the
camera and the monitor or DVR.
10
2. Connect a external power source to the power input
jack of the camera.
Installation
Note:
PRODUCT CENTE
R POSITION
CABLE HOLE (LCV5
CABLE HOLE (LCD5 300)
300)
FRONT
SELFTAPPING SCREW
4 Place
MEZ62687703
FRONT
Follow the instructions below to surface mount the camera
with supplied camera mounting bracket.
SELFTAPPING SCREW
4 Place
MEZ62687703
Use the installation guide template to check the
mounting location. Face the front of the label toward
the area of interest. Using the template as a guide,
make a hole through the ceiling.
1.
PRODUCT CENTE
R POSITION
Refer the manual of Dome bracket adaptor when you
mount the camera on the wall, pendant and parapet.
CABLE HOLE (LCV5
CABLE HOLE (LCD5 300)
300)
Surface mount
Pass the connection cable through the inner side of
the ceiling.
2.
Mounting the Camera
PRODUCT CENTER
POSITION
CABLE HOLE (LCV5300
CABLE HOLE (LCD5300))
PRODUCT CENTER
FRONT
SELFTAPPING SCREW
4 Place
MEZ62687703
SELFTAPPING SCREW
4 Place
MEZ62687703
FRONT
SELFTAPPING SCREW
4 Place
FRONT
MEZ62687703
POSITION
POSITION
CABLE HOLE (LCV5300
CABLE HOLE (LCD5300))
PRODUCT CENTER
CABLE HOLE (LCV5300
CABLE HOLE (LCD5300))
11
PRODUCT CENTER
POSIT
CABLE HOLE (LCV5300
CABLE HOLE (LCD5300 )
)
W
Installation
PRODUCT CENTER
POSITION
POSITION
FRONT
SELFTAPPING SCREW
4 Place
MEZ62687703
SELFTAPPING SCREW
4 Place
MEZ62687703
FRONT
CABLE HOLE (LCV53
CABLE HOLE (LCD53 00)
00)
PRODUCT CENTER
CABLE HOLE (LCV53
CABLE HOLE (LCD53 00)
00)
12
Connect the cables to the cable jacks of the camera
body.
4.
Install the camera mounting bracket to the ceiling.
3.
Installation
5.
Assemble the camera and the housing. Make sure
when you assemble the camera in the right direction.
And then, assemble the dome cover and lens cover.
6.
Use the supplied wrench to tighten the screws
13
Installation
Image Adjustment
You can manually adjust the pan/tilt/azimuth angles, focus,
and zoom while observing the connected monitor.
Notes:
•
Do not hold the camera by lens unit to adjust panning,
tilting, or azimuth.
•
The video output to the BNC will be interrupted while
a portable monitor is connected to the video jack.
1. Use the supplied wrench to loosen the screws and
remove the dome cover Remove the Dome cover and
lans cover.
14
2. Connect a portable monitor to the video jack.
Installation
3.
Adjust the pan/tilt/rotate position of the camera.
4.
Adjust the zoom.
4-1. Unlock the zoom lever.
4-2. Move the lever to adjust the zoom.
4-3. Lock the lever.
TILT
TILT
FAR
NEAR
TELE
PAN
WIDE
ROTATE
15
Installation
5. Adjust the focus.
6. This camera utilizes an on-screen user MENU. To set
items on the menu, use the following buttons. After
then attach the lens cover and dome cover.
5-1. Unlock the focus lever.
5-2. Move the lever to adjust the focus.
5-3. Lock the lever.
FAR
16
NEAR
Menu Operation
•
UP button:
Used to move upper direction on the menu screen.
Use this button to select an item or adjust the parameters.
•
DOWN button:
Used to move lower direction on the menu screen. Use
this button to select an item or adjust the parameters.
•
RIGHT button:
Moves the cursor to the right. Used to increment the
value selected in the menu. The parameter changes
each time this button is pressed.
•
DOWN
LEFT
RIGHT
LEFT button:
Moves the cursor to the left. Used to decrement the
value selected in the menu. The parameter changes
each time this button is pressed.
SET
UP
•
SET button:
Executes selections and displays a submenu for an
item with the mark.
17
Menu Operation
-The following table shows the list of menu items and
options. You can adapt the camera to your requirements by
setting up the respective items in these menus.
Main
Menu
Sub Menu
Contents
BACKLIGHT
EXPOSURE
ALC /ELC
BRIGHTNESS
0 to 100
AGC
OFF/LOW/MIDDLE/
HIGH
SHUTTER
1/120 000, ..., 1/160,
A.FLK, OFF, AUTO, x2,
..., x512
18
ON/OFF
LEVEL
LOW/ MIDDLE/ HIGH / USER
DWELL
TIME
3 SEC to 60 SEC
EXIT
DAY
NIGHT
BURST
ON/OFF
EXIT
TOP/RET/END
OFF
TOP/RET/END
-
AUTO
-
AWC / SET
KEY
-
TOP/RET/END
-
AUTO
EXIT
MANUAL
DAY/NIGHT
Contents
BURST
OFF
ATW
RED
Sub Menu
AUTO
OFF/BLC/HSBLC
SENS-UP
WHITE BAL
Main
Menu
AREA
SETUP
MOTION
DET
ON
AREA
SELECTION
STATE
POSITION ,/
POSITION ;.
SIZE ,/
SIZE ,/
EXIT
-100 to 100
BLUE
-100 to 100
EXIT
TOP/RET/END
1 to 8
ON / OFF
0 to 7
0 to 5
1 to 8
1 to 6
TOP/RET/
END
0 to 100
SENSITIVITY
DISPLAY
OUTLINE,MASK1,MASK2,OFF
ALRAM
MESSAGE,OFF
OUT
EXIT
TOP/RET/END
Menu Operation
Main
Menu
Sub
Menu
3D-DNR
Sub
Menu
Contents
0 to 100
OFF
MASK
SELECTION
1 to 8
DISPLAY
OFF,MOZAIC,
COLOR1 to COLOR 8
RECTANGLE POSITION ,/
POSITION ;.
PRIVACY
MASK
Main
Menu
Contents
ON
CIRCLE
PRIVACY
MASK
ON
POLYGON
2 to 98
2 to 98
SIZE ,/
4 to 100
SIZE ,/
4 to 100
EXIT
TOP/RET/END
MASK
SELECTION
1 to 4
DISPLAY
OFF,MOZAIC,
COLOR1 to COLOR8
POSITION ,/
0 to 100
POSITION ;.
0 to 100
SIZE ,/
1 to 15
SIZE ,/
1 to 15
RADIOUS
1 to 100
EXIT
TOP/RET/END
MASK
SELECTION
1 to 2
DISPLAY
OFF,MOZAIC,
COLOR1 to
COLOR 8
SHAPE
-
POSITION
-
EXIT
TOP/RET/END
EXIT
TOP/RET/END
OFF
D-ZOOM
D-EFFECT
SPECIAL SHARPNESS
COLOR
ON
ZOOM
x1.0 to x16.0
PAN
-100 to 100
TILT
-100 to 100
EXIT
TOP/RET/END
OFF / MIRROR / ROTATE / V-FILP
0 to 100
0 to 100
SYNC
INT / LL
USER TITLE
ON / OFF
LANGUAGE
ENG/CHN/KOR/JAP/FRE/ITA/ESP/POR/DUT/GER/
POL/RUS/TUR/ARA/HEB
EXIT
TOP/RET/END
19
Menu Operation
Main
Menu
SYSTEM
Sub
Menu
FACTORY
RESET
EXIT
Contents
TOP/RET/END
General Operation
1.Press [SET] button.
The setup menu screen appears on the monitor.
EXIT
2.Use [UP] or [DOWN] button to select an option then
press [SET] button. Submenu appears on the monitor.
3.Use [UP] or [DOWN] button to select a submenu
option.
4.Use [LEFT] or [RIGHT] button to select a value.
•
•
•
20
TOP: Return to the CAMERA SETTING menu
screen.
RETURN: Return to the previous.
END: Exit the setup menu.
Menu Operation
Exposure Settings
You can set the exposure options using the EXPOSURE
menu.
1.
Backlight setting
Use Backlight option to view the object clearly in backlight
conditions.
Select [EXPOSURE] option on the [CAMERA SETTING]
menu.
2.Use [LEFT] or [RIGHT] button to select a mode.
3.Press [SET] button and the EXPOSURE menu appears.
1.
Select [BACKLIGHT] option.
2.Use [LEFT] or [RIGHT] button to select a mode then
press [SET].
•
BLC: Camera's backlight compensation feature
helps alleviate issues of visibility in high contrast
areas. Set the BLC limit.
•
HSBLC: Use for masking brightness of the specific
area to view the subject more clearly. The HSBLC
mode is automatically activated only in low
21
Menu Operation
luminance scene.
BRIGHTNESS setting
AREA SETTING: Use [LEFT] or [RIGHT]
button to select a area then use [UP] or
[DOWN] button to select a [ON] or [OFF].
Press [SET] to exit the Area setting menu.
>> GRAY SCALE: Use [LEFT] or [RIGHT] button
to select a gray scale.
>> USER SCALE: Use [LEFT] or [RIGHT] button
to select a bright level. (5 level)
>> MASK: Use [LEFT] or [RIGHT] button to
select [ON] or [OFF].
If you set the MASK to ON, the mask
function is activate only when the HSBLC is
automatically activated in low luminance
scene.
OFF: Not used.
You can increase the brightness of the darkened video.
If you set the brightness to lower value, the image is
darkened. If you set the brightness to higher value, the
image gets bright.
>>
•
22
1.
Select [BRIGHTNESS] option.
2.Use [LEFT] or [RIGHT] button to set the bright level.
Menu Operation
AGC (Automatic Gain Control) setting
SHUTTER (Shutter Speed) setting
If the images are too dark, change the maximum [AGC]
value to make the images brighter.
Select the desired shutter speed for camera exposure. You
can change the shutter speed to higher speed to capture
fast-moving subjects, though the image becomes darker.
1.
Select [AGC] option.
2.Use [LEFT] or [RIGHT] button to select a mode.
1.
Select [SHUTTER] option.
2.Use [LEFT] or [RIGHT] button to set shutter speed.
Note:
When the SHUTTER is set to AUTO, the picture may become
unstable if the camera faces a bright fluorescent light
directly. Therefore, take care when installing.
23
Menu Operation
SENS-UP setting
Note:
If pictures are not clear due to darkness, this SENS-UP
operation would increase the sensitivity of picture.
•
If you set to one of the SHUTTER options except AUTO
on the [SHUTTER] menu, the [SENS-UP] setting is not
available and [---] mark is displayed.
White Balance settings
Select the method by which the camera shifts its output
colors to compensate for the color of a light source.
1.Use [UP] or [DOWN] button to select [SENS-UP]
option.
2.Use [LEFT] or [RIGHT] button to select mode.
•
AUTO: Adjust the sensitivity of the picture
automatically.
>>
•
24
SENS-UP LIMIT: Use [LEFT] or [RIGHT]
button to set the SENS-UP limit.
OFF: Not used.
1.
Select [WHITE BAL] option.
2.Use [LEFT] or [RIGHT] button to select a mode then
press [SET].
Menu Operation
•
ATW (Auto-Tracing White Balance): Use [LEFT]
or [RIGHT] button to select the ATW then press
[SET] button.
•
AUTO: Use [LEFT] or [RIGHT] button to select the
AUTO then press [SET] button.
•
AWC/SET KEY: If you select the AWC/SET
KEY mode, you will be able to set up the White
Balance automatically using [SET] button.
•
MANUAL: You can set the white balance options
manually.
>>
>>
RED: Obtains the optimum amount of red
gain.
BLUE: Obtains the optimum amount of blue
gain.
Day/Night Setting
1.
Select [DAY/NIGHT] option.
2.Use [LEFT] or [RIGHT] button to select mode
for Day/Night function.
•
AUTO: You will be able to change the Day/Night
mode automatically.
Note:
If you set the AGC to [OFF], the AUTO mode of
the DAY/NIGHT function is not available and [---]
mark is displayed.
>>
BURST: Use [LEFT] or [RIGHT] button to
25
Menu Operation
•
select [ON] or [OFF].
LEVEL: Use [LEFT] or [RIGHT] button to
select a level.
>> DWELL TIME: Use [LEFT] or [RIGHT] button
to select a dwell time.
DAY: Color mode enabled.
•
NIGHT: Black-and-white mode enabled.
>>
Motion Detection Setting
The motion detection detects the moving objects in the
scene by monitoring changes in brightness level. You can
select the level of sensitivity for motion detection to 8 zone.
BURST: Use [LEFT] or [RIGHT] button to
select [ON] or [OFF].
Note:
>>
Select the BURST [ON] or [OFF] when the color
noise occurs on the screen in NIGHT Mode after
operating the Line-Lock.
1.
Select [MOTION DET] option.
2.Use [LEFT] or [RIGHT] button to select a [ON] and
press [SET]. The MOTION DETECTION menu appears.
3.
26
Select [AREA SETUP] option.
•
Use [LEFT] or [RIGHT] button to select a area (1/8
to 8/8) on the [AREA SELECTION].
•
Use [LEFT] or [RIGHT] button to set up the ON or
Menu Operation
OFF on the STATE.
•
Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
>>
4.
POSITION,/: Moves horizontal position
of the mask.
>> POSITION;.: Moves vertical position of
the mask.
>> SIZE,/ : Enlarge or decrease the
horizontal size of the mask.
>> SIZE;.: Enlarge or decrease the vertical size
of the mask.
Use [SENSITIVITY] option to obtain the optimum
detection level.
3D-DNR Setting
5.Use [LEFT] or [RIGHT] button to select the DISPLAY
option.
1.
Select [3D-DNR] option.
If pictures are not clear due to brightness, this option
would reduce the noise of picture.
2.Use [LEFT] or [RIGHT] button to select a value.
6.Use [LEFT] or [RIGHT] button to select the ALARM
OUT option.
27
Menu Operation
Privacy Mask Setting
>>
This function is aiming at the protection of personal
privacy, selecting a screen part black not to be displayed in
the screen. Up to 14 zones can be registered.
•
Use [UP] or [DOWN] to select an option then
use [LEFT] or [RIGHT] button to adjust the
option.
-POSITION,/: Moves horizontal
position of the mask.
-POSITION;.: Moves vertical position
of the mask.
-SIZE,/: Enlarge or decrease the
horizontal size of the mask.
-SIZE;.: Enlarge or decrease the
vertical size of the mask.
CIRCLE :
>>
1.
Select [PRIVACY] option.
2.Use [LEFT] or [RIGHT] button to select a [ON] and
press [SET]. The PRIVACY SETUP menu appears.
•
RECTANGLE:
>>
>>
28
Use [LEFT] or [RIGHT] button to select a
mask on the [MASK SELECTION].
Use [LEFT] or [RIGHT] button to set up the
DISPLAY option.
>>
>>
Use [LEFT] or [RIGHT] button to select a
mask on the [MASK SELECTION].
Use [LEFT] or [RIGHT] button to set up the
DISPLAY option.
Use [UP] or [DOWN] to select an option then
use [LEFT] or [RIGHT] button to adjust the
option.
-POSITION,/: Moves horizontal
position of the mask.
-POSITION;.: Moves vertical position
Menu Operation
of the mask.
SIZE,/: Enlarge or decrease the
horizontal size of the mask.
-SIZE;.: Enlarge or decrease the
vertical size of the mask.
-RADIUS SIZE : You can adjust the
RADIUS SIZE.
POLYGON :
--
•
>>
>>
>>
>>
Notes:
•
You can adjust the mask color manually except
for COLOR 8.
•
RED, GREEN, BLUE and TRANSPARENCY
adjustments are applied in common from COLOR
1 to COLOR 7, after mask setting.
Use [LEFT] or [RIGHT] button to select a
mask on the [MASK SELECTION].
Use [LEFT] or [RIGHT] button to set up the
DISPLAY option.
Use the [LEFT], [RIGHT], [UP], [DOWN],
[SET] button to draw the polygon on the
[SHAPE].
Use the [LEFT], [RIGHT], [UP], [DOWN],
[SET] button to move the polygon on the
[POSITION].
29
Menu Operation
Special Menu Settings
This menu lets you adjust and set up D-ZOOM, D-EFFECT,
SHARPNESS, COLOR, SYNC, USER TITLE, LANGUAGE
function by yourself in the SPECIAL menu.
Setting the D-ZOOM (Digital Zoom ) level
You can select the digital zoom level.
1.
1.
Select [SPECIAL] option.
2.Press [SET] button and the SPECIAL menu appears.
30
Select [D-ZOOM] option on the [SPECIAL] menu.
2.Use [LEFT] or [RIGHT] button to select a [ON] then
press [SET] the DIGITAL ZOOM menu appears. When
you set to ON, the displayed image can be shaking.
3.Use [UP] or [DOWN] to select a option then use
[LEFT] or [RIGHT] button to select a level.
•
ZOOM: Use [LEFT] or [RIGHT] button to enlarge
the screen.
•
PAN: Use [LEFT] or [RIGHT] button to move the
screen. (left or right)
Menu Operation
•
TILT: Use [LEFT] or [RIGHT] button to move the
screen. (up or down)
Setting the D-EFFECT (Digital effect)
Setting the SHARPNESS effect
The degree to which the boundary of the two portions is
clearly distinguished.
You can select the digital effect.
1.
1.
Select [D-EFFECT] option on the [SPECIAL] menu.
2.Use [LEFT] or [RIGHT] button to select a digital effect.
•
V-FLIP: Flip the picture vertically.
•
MIRROR: Turn on the mirror effect.
•
ROTATE: Rotate the picture. (180°)
•
OFF: Turn off the digital effect.
Select [SHARPNESS] option on the [SPECIAL] menu.
2.Use [LEFT] or [RIGHT] button to change a adjust
the option. If you set the sharpness value to higher,
the image outline becomes sharp. If you set to lower
value, the image outline becomes dim.
31
Menu Operation
Setting the COLOR
SYNC Setting
You can switch the displayed picture to gray scale or color.
1.
Select [COLOR] option on the [SPECIAL] menu.
2.Use [LEFT] or [RIGHT] button to change a color effect.
32
•
ON: To display the picture with color.
•
OFF: To display the picture with grayscale.
1.
Select [SYNC] option on the [SPECIAL] menu.
2.
The [SYNC] option is set to [INT] automatically.
Note:
AC24V Adaptor have to use for the [LL] mode setting.
Menu Operation
Setting the USER TITLE
•
You can use the camera identification to assign a number
and character to the camera.
The USER TITLE is displayed on the upper left of the screen.
To disappear the user title, select [OFF].
•
1.
Select [USER TITLE] option.
A (Blank): Inserts a space at the cursor position.
/
: Moves cursor to left or right.
LANGUAGE Setting
Select the viewer language for the camera setup menu and
OSD information display.
2.Use [LEFT] or [RIGHT] button to select a [ON] then
press [SET]. The USER TITLE menu appears.
A
3.Use [UP], [DOWN], [LEFT] or [RIGHT] button to select
a character or number then press [SET] button.
•
CLR: Clear all entered characters and numbers.
•
POS: Move the USER TITLE position on the screen
using the arrow buttons.
•
END: Confirm your selection or exit the setting
1.
Select [LANGUAGE] option on the [SPECIAL] screen.
2.Press [LEFT] or [RIGHT] button to select a language.
33
Menu Operation
SYSTEM Setting
1.
Select the [SYSTEM] menu.
2.
Press [SET] button and the [SYSTEM] menu appears.
3.
Use [UP] or [DOWN] button to select the option.
•
4.
FACTORY RESET: To reset the camera setting
to factory setting, select the [FACTORY RESET]
option.
Press [SET] button to confirm your selection.
Note:
The menu screen is move to top menu, after set up
[FACTORY RESET].
34
Specification
Item
LCV5100-BN
Signal System
NTSC
PAL
Total/Effective Pixels Number
520 000 Pixels / 480 000 Pixels
610 000 Pixels / 570 000 Pixels
Image Device
LCV5100-BP
6 mm (1/3 Type) Exview HAD CCD II
DSP
XDI-V
Lens
2.8 mm to 11 mm Vari-focal Lens, F1.2
Digital Zoom
x16
IRIS Control
DC
Sync. System
Internal / Line Lock
Scanning Frequency (H/V)
Horizontal Resolution
15.734 KHz / 59.94 Hz
15.625 KHz / 50 Hz
650 TV Lines (Color), 700 TV Lines (B/W)
S/N Ratio
50 dB
Minimum Illumination
(30 IRE,F1.2)
0.03 lx (Sens-up Off ), 0.000 3 lx (Sens-up Auto), 0.000 001 lx (Sens-up x512)
Video Output Signal
1 Vp-p Composite (75 Ω)
Day & Night
Digital (AUTO / DAY / NIGHT)
BACKLIGHT
BLC / HSBLC / OFF
35
Specification
Item
LCV5100-BN
DNR
Electronic Shutter Speed
White Balance
LCV5100-BP
2D + 3D-DNR
1/60 to 1/120 000
1/50 to 1/120 000
ATW / AUTO / AWC/SET KEY / MANUAL
Motion Detection
8 Zones
Privacy Zone Masking
14 Masks
Digital Effect
OFF / MIRROR / ROTATE / V-FILP
Communication
Coaxial Communication
Power Source
DC 12 V / AC 24 V
Power Consumption
190 mA
Operation Temperature/
Humidity
-10 ºC to 50 ºC / 0 % RH to 80 % RH
Storage Temperature/ Humidity
-20 ºC to 60 ºC / 0 % RH to 90 % RH
Dimension (Ø x H)
140 mm x 122 mm
Weight
710 g
36
Download PDF

advertising