LG | LNB3100 | LG LNB3100 Owner’s Manual

OWNER'S MANUAL
High Definition Network Camera
Please read this manual carefully before operating your set and retain it for future reference.
MODEL
LNB5100 series
LNB3100 series
LND5100 series
LND3100 series
LNV5100 series
1303 (V1.5)
Contents
Introduction.................................................................................... 3
Day/Night settings..............................................................44
3D-DNR setting.....................................................................44
Operation and settings.................................................................. 4
Before using the system......................................................................4
Recommended PC Requirements....................................................4
Accessing the LG IP device.................................................................5
LG Smart Web Viewer Overview.......................................................6
Configuration menu overview...........................................9
Configuring the LG Network Camera Device...............................9
Accessing the Configuration menu..................................9
System settings.....................................................................10
Audio & Video settings.......................................................17
Network settings..................................................................20
User settings..........................................................................27
Event settings........................................................................29
OSD Menu Setup.................................................................................39
General Operation...............................................................41
Exposure settings.................................................................41
White Balance settings.......................................................43
2
Privacy setting.......................................................................45
Special menu settings........................................................46
SCENE mode setting (Optional)......................................48
Reset setting..........................................................................49
Reference...................................................................................... 50
Troubleshooting..................................................................................50
Open source software notice..........................................................53
Specifications.......................................................................................54
Introduction
The LG Network Camera is designed to use on an Ethernet network and must be assigned an IP address to make it accessible.
This manual contains instructions on how to install and manage the LG Network Camera in your networking environment. Some knowledge
of networking environments would be beneficial to the reader.
Note that design and specification of this unit may differ from the manual as quality improvement. Should you require any technical
assistance, please contact authorized service center.
Features Chart
This table shows the differences between the models.
Item
LNB5100
LND5100
LNB3100
LND3100
LNV5100
VA
Yes
Yes
No
No
Yes
Audio
Yes
Yes
No
No
Yes
Sensor&Relay
Yes
Yes
No
No
Yes
ALC2
Yes
Yes
Yes
No
Yes
SCENE Mode
Yes
Yes
No
No
Yes
OSD
Introduction3
Operation and settings
Before using the system
Recommended PC Requirements
•
Before using the LG IP device make sure the connections are
correct and verify whether proper power supply is used.
The LG IP device can be used with most standard operating systems
and browsers.
•
Check the connections of the LG IP device for the correct
conditions.
•
Check that the LG IP device is(are) connected to the network and
that power is supplied.
•
Once the connections are made you need to install the LG client
program to the PC from which you want to access the device.
The LG Smart Web Viewer program is automatically installed
when you connect the LG IP device.
The LVi510 and the LG Smart Web Viewer program are the
network program of the LG Video Server and the LG IP cameras.
•
To view streaming video in Internet Explorer, set your browser
to allow ActiveX controls. If you find this message “This website
wants to install the following add-on: ‘IPCam_Streamer.cab’ from
‘LG ELECTRONICS INC’”, Click the yellow bar and install LG Smart
Web Viewer Program on your computer. Please set your browser
zoom level to 100%.
•
The Layouts and the Live view pages may differ with different OS
(Operating Systems) and Web Browsers.
•
Care needs to be taken not to run any other applications when
the Client Program is running as it may cause memory shortage.
4
Items
Operating System
CPU
Web Browser
Requirements
Windows XP Professional,
Windows VISTA, Windows 7
Intel Core2 Quard Q6700 (2.66 GHz) or
above
Microsoft Internet Explorer (32 bit) above
the version 7.0 and below the version 9.0.
DirectX
DirectX 9.0c (Windows XP), DirectX 11
(Windows VISTA, Windows 7) or above
Memory
2 GB or above RAM
Graphics Card
Resolution
256 MB or above Video RAM
2048 x 1536 (with 32 bit color) or higher
Operation and settings
Accessing the LG IP device
default administrator user name and password are
“admin”.)
You can access the LG IP device by following the below steps.
1.
Default password must be changed for security after
initial connection.
Install LVi510 Program
It recommended to use LVi510 surely.
2.
Note:
Discover the LG IP device using the IP Utility
The IP Utility can automatically discover and display LG IP
devices on your network.
3.4 Notes:
•
The IP Utility shows the MAC address, IP address, Model
name and so on.
3.2 Enter the IP address of the LG IP device in the address
bar of the browse.
The computer running the IP Utility must be on the same
network segment (physical subnet) as the LG IP device.
3.
Run the IP Utility program.
2.2 Click the [Search] button or select the [Search] option
in the Device search menu.
After a few seconds the found LG IP devices gets
displayed in the IP Utility window.
3.3 Enter the user name and password set by the
administrator.
3.4 Click the [OK] button and then the LG Smart Web
Viewer is displayed in your browser.
•
The LG Smart Web Viewer needs more time to display it
according to the network conditions.
•
If the login window is not displayed, check the pop-up
blocker. If you set the pop-up blocker, the login window
is not displayed. You must allow the pop-ups.
•
If you connect the LG Smart Web Viewer for the first time,
the Security Warning window is displayed to install the
LG Smart Web Viewer program. You must install the LG
Smart Web Viewer program for using the LG IP device.
•
If your computer or network is protected by a proxy or
firewall, the proxy or firewall settings can prevent the LG
Smart Web Viewer program. Change the proxy or firewall
settings to activate the LG Smart Web Viewer program.
Logging in to the LG Smart Web Viewer
3.1
Run the IP Utility and find the LG IP devices.
3.2
When the LG IP devices appear in the IP Utility
window, double-click IP address or right click on the
same IP address and select “Connect to Web Page”
to start the LG Smart Web Viewer. When accessing
the LG Smart Web Viewer, the authentication dialog
appears on the screen.
3.3
Enter the user name and password. (Note that the
You can also access the LG Smart Web Viewer as shown
below.
3.1 Start your Web browser.
Note:
2.1
Click the [OK] button and then the LG Smart Web
Viewer is displayed in your browser.
Operation and settings5
LG Smart Web Viewer Overview
It displays Video Codec, Resolution and
FPS of the selected video stream.
Check this option as the network
connection type (TCP or UDP). If you
check it, the client connects to the server
using TCP connection.
Select buffering time of live stream.
Click to display the check box of
[Hostname], [Framerate] and [Bitrate]
options. [Display] is displayed on left
top of the live view window in order of
selecting options.
Video Analysis
>> Hide: Video Analysis display
function is not in use.
Item
Description
Select the video image size from the
drop-down list.
The initial view size is set to D1.
Notes:
>> MD: Displays the Motion
Detection function to the live
view window.
•
Note:
•
6
>> SVA: Displays the Smart Video
Analysis function to the live view
window.
Select [FULL SCREEN] to enlarge full
screen of monitor. To return previous
screen, press ESC key or double click.
When you select [AUTO RESIZE], size
of live view screen fit to window.
Ratio imaging is fixed by width
based.
When you use the DPTZ function, all
of Display function is deactivated for
a while.
Operation and settings
Click to effect and then check the check
box of [Edge Enhancement] option. The
user gets more sharp reception on the
live view window.
Provides all the necessary tools
for setting up the device to your
requirements. The user will need
administrator level to do this.
Note:
Note:
This feature only affects the live view
window.
Click to save the current image in JPEG
format on your computer.
If you want to exit the Configuration
menu, select one of the video stream in
the Live view drop-down list.
1. Click the [Snapshot] button and then
the Snapshot window is displayed.
Displays the current surveillance live
screen. You can monitor the camera
image on the live view window of the LG
Smart Web Viewer.
2. Click the [Save] button in the
Snapshot window.
3. Enter the file name (JPEG format) and
select the folder to save it.
4. Click the [Save] button to confirm it.
5. Click the [Close] button in the
Snapshot window to close it.
Displays the Camera OSD control
window. Use these buttons to setup the
Camera. This button does not appear on
the screen if the login is other than the
administrator.
Select the video stream. From the Live
view drop-down list, select the desired
video image source.
Click this button and drag the area to use
PTZ function. Right-clicking the screen
will bring up the previous magnification.
(Color icon: On, Gray scale icon: Off.)
Note:
You can set the stream configurations
independently. This would facilitate the
user to set the live view at his comfort.
Operation and settings7
1. Click this button to open the folder
browse window. Click the button
again in next time, video is recorded
automatically without selection of
folder.
Note:
If you want to change the folder,
move to other pages or press the
refresh button.
Click this button to switch the
microphone off and on for the computer.
The option depends on the model.
(Color icon: On, Gray scale icon: Off.)
Click this button to switch the sound off
and on, for the speaker of the computer.
The option depends on the model.
(Color icon: On, Gray scale icon: Off.)
2. Recording button is activated and
recording will be started.
Note:
If recording exceed the time(1 hour)
or size limit (1 GB), recording is
stopped automatically with warning.
3. To stop the recording, click this
button during the recording.
Click this button to connect or
disconnect the audio communication
between the LG IP device and the
connected PC. The option depends on
the model.
(Color icon: On, Gray scale icon: Off.)
8
Operation and settings
Configuration menu overview
Event server
The following table shows the list of menu items.
Sensor & Relay
The configuration images are different from each model.
Main Menu
Sub Menu
Triggered Event
Date & Time
Scheduled Event
Storage
Option
Text Overlay
Option
Language
Stream
Basic
RTP stream
TCP/IP
DDNS
Network
IP filtering
Configuring the LG Network Camera
Device
Only administrator-level users have permission to access the
Configuration menu.
Camera
Audio
Option
The features and options of the LG IP camera are configured
through the Configuration menu.
Log & Report
Audio & Video
Motion detect
Smart analytics
Version
Maintenance
System
Event
Option
Option
Accessing the Configuration menu
Click the [Configuration] button to display the LG Smart Web Viewer
configuration window.
Warning
The Configuration setup should be made by qualified service
personnel or system installers.
SNMP
QoS
802.1x
SIP
User
Basic
Operation and settings9
System settings
Time zone
Version
Set the time difference from GMT in the area where the IP device
is installed. Select the time zone in the area where the IP device is
installed from the drop down list.
Displays the current Model Name and Software version.
Time mode
>> Synchronize with NTP Server: Select if you want to
synchronize the IP device’s date and time with those of the
time server called NTP (Network Time Protocol). Specify the
NTP server’s name. Click the [Test] button for connection test
to the server.
>> Synchronize with personal computer: Select if you want
to synchronize the IP device’s date and time with your
computer.
>> Synchronize manually: Select if you want to set the IP
device’s date and time manually. Select the year, month and
date by clicking the calendar button. Set hour, minutes and
seconds in the edit boxes.
Date & Time
Notes:
•
When system reboot after time setting, time of system
could be delayed. If you set the time correctly, set the
[Synchronize with NTP server] option.
•
Refer to NTP configuration as operation system of
the Recording Server when the Recording Server use
recording function and NTP server.
Server time
>> Server time: Displays the current date and time of the IP
device.
•
10
Save: Click this button to confirm the settings.
Operation and settings
Maintenance
Note:
Backup and Restore can happen on IP device having the
same version of firmware. This feature is not intended for
multi-configurations or for firmware upgrades.
Firmware
>> Upgrade
1. Click the [Browse] button.
2. Find and open the firmware file.
3. Click the [Upgrade] button to update the firmware.
Note:
System reboot
When you upgrade the system, it may take some minutes
to be done. Do not close the browser while the upgrade
is in progress. If you close the browser, it may cause a
malfunction. You should wait until the confirmation window
is displayed. When the upgrade is finished, the confirmation
window will be displayed.
Click the [Reboot] button to restart the IP device. It takes some
minutes for the IP device to start again.
Backup and restore
>> Backup: To take a backup all of the settings. If necessary, it
make possible to return to a backup configuration.
1. Click the [Backup] button.
2. Click the [Save] button.
3. Follow the instructions on the browser to specify the
folder.
4. Click the [Save] button to save the settings.
>> Restore:
>> Initialize: The [Initialize] button should be used with caution.
Clicking it will return all of the IP device’s settings to the
factory default values. Except for the Network settings, PTZ
Protocol and Preset settings. (The option depends on the
model.)
Note:
Refer the “Clear browser’s cache” of Troubleshooting.
1. Click the [Browse] button.
2. Find and open the file in which the configuration setting
data is stored.
3. Click the [Restore] button and the system settings will be
restored and reboot the system.
Operation and settings11
Storage (Optional)
>> Set as NTP server IP: Click this button to use the entered
Recording Server IP as the NTP server IP.
Notes:
•
The recorded file name is made automatically as the
“[Created date of the file]_[GMT Recording Time].DAT”
type.
•
If the capacity of the SD card remains less than 200 MB,
stop recording or overwrite new file after delete old one
as [Overwrite] setting. The overwritten file can not play
or may malfunction when you download.
•
Recorded file on the SD card, is recording 1 frame per
second when set video codec to MJPEG.
Device Management
Note:
SD Card function may not be supported in specific countries.
General
>> Overwrite: If the micro SD card has insufficient space and
this option will be activated. It will overwrite the oldest data.
>> DiskFull Notification: Sends an warning e-mail to the SMTP
server when the micro SD card has fully recorded. Select the
SMTP server from the drop-down list. You should register the
SMTP server on the Event server setting to set this function.
>> Network Failure Recording: Select the check box to activate
the micro SD card recording function. If the system does
not work with recording server, the system will record the
data to the micro SD Card. When the system connect to the
recording server again, the recorded data of the micro SD
card will transfer to the recording server automatically.
>> Recording Server IP: Enter the recording server IP.
12
>> Using the micro SD card
1. Insert the micro SD card carefully to the micro SD card
slot of the camera.
2. Click the [Mount] button. If the micro SD card is mounted
to the system correctly, the [Mount] button will be
changed to the [Unmount] button.
3. Displays the information of the[Disk ID], [Status],
[Capacity] options.
Notes:
•
When the micro SD card is mounted, you should format
the micro SD card. After the micro SD card format is
finished, you should click the [Mount] button to use it.
•
When you use the micro SD card format function, it may
not progress immediately. In this case, you should try it
again after waiting a few minutes.
>> Remove the micro SD card
1. Click the [Unmount] button. If the micro SD card is
Operation and settings
unmounted from the system correctly, the [Unmount]
button will be changed to the [Mount] button.
2. Remove the micro SD card from the micro SD card slot of
the camera.
File Management
Displays the recorded file of the micro SD card on the list. Click the
[Search] button to display the recorded file. The list will be updated
when you click the [Search] button.
Note:
>> To view the recorded file of the micro SD card
When you use the Unmount function, it may not progress
immediately. Operations such as recording of the system and
reading of data are required stop time before the Unmount
function is activated. You should try it again after waiting a
few minutes.
1. Select the search option.
>> File Format: You can selects the Recording File Format(AVI
or DAT). Recording, Search and Download are available
according to the setting.
--
Some: You can set the search condition by using the
date and time options.
>> Download: You can download the recorded data of the
list to your PC. Select a recorded file on the list and click
the [Download] button. The two confirmation window
is displayed. You should download the all files that the
recorded file(*.DAT) and information file(*.INFO). You can
download as AVI file according to File format.
Notes:
•
All: Search the all recorded files in the micro SD card.
2. Click the [Search] button and then the search result is
displayed on the list.
File Format
•
--
SD Recording or FTP(Video) Sending Format are set
according to the setting. When you select to AVI, [Auto
Recording function] may not be activated in case of
network error.
Notes:
IP Camera’s time will be appeared in players based on
DirectShow such as Windows Media Player and MPlayer.
•
It is recommended to deactivate the [Overwrite] function
before you download the file. When [Overwrite] function
is activated, the downloading file might be overwritten,
if the micro SD card has insufficient space.
•
The downloaded file can be played by using the LG File
player.
>> Remove: Delete file from the SD card.
•
Save: Click this button to confirm the settings.
Operation and settings13
Text Overlay
Text Overlay (Optional)
Text Overlay
>> Enable: Set to ON or OFF. Setup menu is appeared when
selects ON.
>> Date & Time : Select the ON to display time and date of
Client PC.
>> Channel Name: Enter the channel name you want to use.
You type the Channel Name, it will be displayed whether you
select the ON or OFF.
>> Flickering: Set to On or OFF.
>> Position: You can designate the position of text from drop
down list.
•
Save: Click this button to confirm the settings.
Note:
The text overlay option may differ in method as to model and
version.
Preview
You can preview the camera image on the preview window.
Mode
>> Normal Mode: Follow the normal procedure of text overlay
option by selecting the [Normal Mode].
>> Multiline Mode: Set more characters, color and size of the
text overlay by selecting the [Multiline Mode]. The saved text
overlay is displayed on the left top of screen.
14
Operation and settings
Basic Configuration
Capture Mode
When you select the [Normal Mode], you can adjust the
[Date&Time], the [Text Information], the [X position], the [Y position]
and the [User Title] function. And other functions are able to adjust
by selecting the [Multiline Mode].
>> Date&Time: Click the check box of [Date&Time] to display
time and date of Client PC.
>> Text Information: Enter characters in the text field. (From
[Text1] to [Text4]) Maximum input characters are depends
on the resolution.
Capture Mode
Column
Row
16:9
24
12
4:3 or 5:4
24
16
16:9
4:3 or 5:4
Font Size
Column
Row
Column
Row
0
32
12
32
16
1
32
12
32
16
2
24
12
24
16
3
18
9
18
12
>> Color: You can make any color by adjusting R.G.B LEVEL.
>> Size: You can adjust the font size.
Notes:
>> X Position: Set the horizontal position of each text overlay.
•
If you change the [CaptureMode], the existing characters
may not be seen partially.
•
The [Multi-Line Text] is an one off feature. When refresh a
browser to connect this option again, the text input field of
[Multi-Line Text] is cleared but contents of text overlay are
remained on a live view screen.
•
If you use below features, text overlay is changed [Normal
Mode]
: [System>Maintenance>Reboot], [OSD Control>Reset],
[Audio & Video>Camera>CaptureMode]
>> Y Position: Set the vertical position of each text overlay.
>> User Title: Enter the user title. The user title is displayed on
the right bottom of screen.
•
Save: Click this button to confirm the settings.
>> Multi-Line Text: Enter characters in the text field. Maximum
input characters are depends on the resolution.
Operation and settings15
Log & Report
Language
Log & Report status
Language list
The System log provides a summary of the status of the IP device.
The unit records the data of the software activity in a file.
Select a language for the LG Smart Web Viewer configuration menu
and information display.
>> View Log: Click this button to display the system log
information.
--
•
Save: Click this button to confirm the settings.
Download: Click this button to see the log information of
system.
>> View report: Click this button to display the report of the
system.
--
Download: Click this button to see the report
information of system.
Note:
The downloaded file is a UNIX type. If you open the file in Microsoft
Note pad, it will display the text as if the file contained no line
breaks at all.
16
Operation and settings
Audio & Video settings
Notes:
•
It is recommended to select Sensor Framerate value to
30 in 60 Hz region, 25 in 50 Hz region to reduce flicker.
•
Maximum FPS is set 25 when you select Sensor
Framerate value 25.
Camera
•
Save: Click this button to confirm the settings.
•
Default: Click this button to restore the IP device back to original
factory settings.
Note:
The Capture mode and Sensor Framerate are not initialized.
Preview
You can preview the camera image on the preview window.
General
>> Contrast: Edit the contrast value from 0 to 100. Selecting 100
provides the image with the highest contrast.
>> Standard: Displays the video standard of the camera.
>> CaptureMode: Select the capture mode.
Note:
If you change the CaptureMode option, the Privacy, WDR/
BLC and HSBLC settings on the OSD menu are initialized.
>> Sensor Framerate: You can select the Sensor Framerate value
between 30 and 25.
Operation and settings17
Stream
>> Quality: Select the Quality.
--
VBR: The bit rate may vary depending on the complexity
of the video to meet the selected quality.
--
CBR: The video quality may vary in order to preserve a
constant bit rate.
>> Stream quality: If the [Quality] option set to VBR, this option
is displayed. Select the stream quality from the drop down
box, the camera supports five types. (Highest, High, Medium,
Low and Lowest)
>> Alias: Enter the profile name you want to use.
Resolution
>> Bit rate: If the [Quality] option set to CBR, this option is
displayed. Edit the bit rate value from 256 kbps to 10 240
kbps.
>> HD: Displays the maximum image size of the camera.
>> SD: Select the output image size of the camera.
Note:
Note:
When you use the Smart Analytics function, SD resolution is
changed as shown below.
Smart Analytics
D1
CIF
Off
704 x 480
352 x 240
On
640 x 384
320 x 192
If the ‘Bit rate’ is configured too low with high resolution,
the actual frame rate will decrease because of narrow
bandwidth. So you need to set or change the ‘Bit rate’ to
high value.
•
Save: Click this button to confirm the settings.
Profile
>> Enable: Click to activate the stream function.
>> Video codec: Select the video mode (Codec) from the dropdown list. The viewer can choose among MJPEG, H.264 and
H.264_HIGH.
>> Maximum frame rate: Set the frame rate of the image.
>> GOP size: It means “Group of Pictures”. The higher the GOP,
the better is the video quality of the camera. Edit the value
of GOP from 1 to 30. This setting is valid for H.264 video
format only.
18
Operation and settings
Region Of Interest
2. Click the edge or corner of the window box to adjust the
window size.
3. Click the [Save] button to save the settings.
Note:
ROI area can not overlap with each other.
You can set and streaming the desired area on the live view window
to use ROI(Region Of Interest) function. Select Profile4(ROI-1) to
Profile7(ROI-4).
>> Enable
1. Click to activate the [Region Of Interest] window. You can
add the 4 windows maximum for ROI function.
Operation and settings19
Audio (Optional)
Network settings
Basic
Audio In
>> Enable: Click the check box if you want to send the audio
from the microphone input connector.
Note:
The Clients connected to the IP device remain unaffected
with additional changes made in the setting.
>> Audio type: Select the codec when you send the audio from
the microphone input connector.
Audio Out
•
General
>> MAC address: Displays the MAC address.
Port & Encryption
>> Enable: Click the check box to output the audio from the
speaker.
>> Network encryption: Select the HTTP or HTTPS option for
security.
Save: Click this button to confirm the settings.
>> Smart Port Setting: Select [On] to allocate a port number
automatically.
Note:
If you select [On], [UPNP Status], [External IP], [Web Port] and
[RTSP Port] options are deactivated.
>> UPNP Status: When you use the router that is supported
UPnP function, you can set the port forwarding
automatically by using the [Smart Port Setting]. [UPnP
Status] shows connected status of router.
>> External IP: When you connect the router that is supported
UPnP function, this option is displayed. Displays the external
20
Operation and settings
IP address allocated router.
>> Web port: The default HTTP port number (80) can be changed
to any port within the range 1 025 to 65 535.
>> RTSP port: Check RTSP port. The default port is 554. Other
ports can be selected within the range 1 025 to 65 535.
RTP stream
RTP (Real-time Transport Protocol) is an internet protocol that allows
programs to manage the real-time transmission of multimedia data,
via unicast or multicast.
Note:
The RTSP port number should not be same with the web
port number.
ARP Ping
>> Enable ARP Ping to configure IP address: Check to enable
ARP ping.
•
Save: Click this button to confirm the settings.
Profile
>> RTP unicast: When enabled the transmission of the data to
the specified equipment happens on a network specifying a
single address.
>> RTP multicast: When enabled it reduces the transmission
load on the camera by making the computer of the same
segment network receive the same transmission data. When
multicast option is checked then select Video Port number,
Audio Port number and Data port number.
--
IPv4 address: Set the IP address for RTP multicast.
--
Base RTP port: Enter the port number of even number
used for the multicast streaming. Each profile uses
successive 6 port number which starts from [Base RTP
port]. It is initially set to 10 000 and you can edit this
between 10 000 and 65 530.
Operation and settings21
Note:
TCP/IP
Each profile using multicast needs its own multicast IP
address and port numbers to avoid address conflict. When
more than 2 profiles use same multicast IP address, each
[Base RTP port] number should be distinguished from the
other port number more than 6 at least.
Multicast
>> Always Multicast: Check to enable multicast regardless of
client connection.
TTL
>> TTL: This option indicates the Time-To-Live of multicast
packets. The default setting is 7, and the allowed TTL range is
from 1 to 255.
•
Save: Click this button to confirm the settings.
IPv4 address status
>> Automatically set with DHCP: Select this option when a
DHCP server is installed on the network to allow IP address
assignment. With this setting, the IP address is assigned
automatically.
--
Notify to SMTP server, if IP address is changed: If you
select this option, the user get a notification mail telling
about changing of IP of the IP device.
Notes:
22
•
You should register the SMTP server on the Event server
setting to set this function.
•
If you select [Automatically set with DHCP], the camera
obtain IP address from DHCP server after IP address is set
“192.168.0.16”.
Operation and settings
>> Statically set: Select this option when you set a fixed IP
address, with this setting, specify the IP address, Subnet
mask and default gateway manually.
--
IPv4 address: Enter an IP address.
--
Subnet mask: Enter a subnet mask address.
--
Gateway: Enter the gateway address.
DDNS
This free service is very useful when combined with the LG DDNS
Server. It allows the user to connect the IP device using the URL,
rather than an IP Address. This also solves the problem of having a
dynamic IP address.
DNS server status
>> Primary DNS server: Enter the Primary domain name server
that translates the host names into IP address.
>> Secondary DNS server: Enter the Secondary DNS server
address that backups the Primary DNS.
IPv6 address status
>> Enable: Click the check box if you want to use the IPv6
address.
>> Mode
--
Manual: Select this option when you set a fixed IP
address manually.
--
Basic: Select this option to allow IPv6 address assignment
based on the Mac address. With this setting, the IP
address is assigned automatically.
--
DHCPv6: Select this option when exist a DHCPv6 server
in network. If DHCPv6 server is not existed or temporary
disability, it requests assignment every 3 minutes.
DDNS status
>> Don’t use DDNS server: Disable the DDNS function.
>> Use DDNS server: Enable the DDNS function.
•
--
Provider: Displays the DDNS provider.
--
Hostname: Enter the host name you want to use.
Save: Click this button to confirm the settings.
>> IPv6 address: You can enter the IP address when you select
the Manual mode. It alarms when you enter the invalid IP
address.
•
Save: Click this button to confirm the settings.
Operation and settings23
IP filtering
--
The access of the IP addresses in the list are allowed or denied
according to the choice made in the drop-down list of the Basic
policy option. The administrator can add up to 10 IP address entries
to the list (a single entry can contain multiple IP addresses). The
users from these IP addresses need to be specified in the user list
with the appropriate access rights. The IP list is to control the access
permission of clients by checking the client IP address.
Deny all: Deny all the IP address basically, but the IP
addresses in the list are allowed. It needs at least one IP
address to activate this function.
•
Save: Click this button to confirm the settings.
•
Add: Click this button to add the IP address.
1. Click the [Add] button.
2. Set the IP options.
--
Alias: Enter the alias.
--
From: Enter the start IP address for the IP filtering.
--
To: Enter the end IP address for the IP filtering.
Note:
If you want to deny or to allow a range of IP addresses, enter
the start IP address to “From” and the end IP address to “To”.
You can also add an IP address by entering the same IP
address to “From” and “To”.
3. Click the [Save] button.
4. Repeat the steps 1 to 3 to add additional IP address.
•
Remove: Click this button to delete the IP address.
1. Select the alias from the list.
2. Click the [Remove] button. The IP address will be deleted.
IPv6 address
•
Add: Click this button to add the IP address.
1. Click the [Add] button.
2. Set the IP address option.
IP list
>> Basic policy: Select the basic policy type.
--
24
Allow all: Allow all the IP address basically, but the IP
addresses in the list are denied.
--
Alias: Enter the alias.
--
IPv6 address: Enter the IP address for IP filtering.
3. Click the [Save] button.
4. Repeat the steps 1 to 3 to add additional IPv6 address.
Operation and settings
•
Remove: Click this button to delete the IPv6 address.
1. Select the alias from the list.
2. Click the [Remove] button. The IPv6 address will be deleted.
SNMP
>> Password: Type the password for the SNMP.
•
Save: Click this button to confirm the settings.
QoS
You can specify network Quality of Service (QoS) settings.
The Simple Network Management Protocol (SNMP) is an application
protocol to exchange the management information of network
devices.
QoS DSCP Configuration
>> Video DSCP: Enter the priority of Video for DSCP
(Differentiated Service Code Point) Quality of Service.
SNMP v1/v2c
>> Audio DSCP: Enter the priority of Audio for DSCP Quality of
Service.
>> Enable SNMP v1/v2c: Selects when SNMP is allowed access
to this device.
>> Read Community: Specifies the SNMP management
community in which you want to read this system.
>> Write Community: Specifies the SNMP management
community in which you want to write this system.
>> Event DSCP: Enter the priority of Event for DSCP Quality of
Service.
•
Save: Click this button to confirm the settings.
SNMP v3
>> Enable SNMP v3: Selects when SNMP v3 is allowed access to
this device. It supports authentication and encryption.
>> SecurityName: Type the security name for the SNMP.
Operation and settings25
802.1x
Basic Configuration
Specifies whether 802.1x network access is enabled.
>> EAPOL Version: Select the EAPOL version.
>> EAP ID: Enter the ID of the client certificate using up to 16
characters.
>> Password: Enter the password of the client private key using
up to 16 characters.
•
Save: Click this button to confirm the settings.
SIP
802.1x/EAPOL using EAP-TLS
>> Enable: Select on to enable the protocol. Current
authorization status of 802.1x port is displayed on buttons
right.
Certificates
>> To upload or remove the certificates
1. Click the [Browse] Button.
SIP Setting
2. Find and open the certificates file.
>> Enable: Set to On when you use the SIP server.
--
CA Certificate: Upload the accredited certificate included
public key.
>> SIP Server: Enter the hostname or IP address of the SIP
register server.
--
Client Certificate: Upload the accredited certificate
included client authentication key.
>> UserName: Enter the name of the device used when making
calls with SIP.
--
Client private key: Upload the accredited certificate
included client private key.
>> Password: Enter the SIP server authorization password.
3. Click the [Upload] button to install certificates.
•
Save: Click this button to confirm the settings.
4. Click the [Remove] button to delete certificates.
26
Operation and settings
Notes:
•
When you set to [On] on the [Enable] option, [Enable
anonymous login] option is enabled automatically.
•
You should set the SIP port number not to conflict with
multicast port and 5353.
User settings
Basic
The IP device is shipped with the login rights of administrator only.
If others need to access the IP device excluding the configuration a
login with viewer rights need to be created. A maximum of 50 users
can be created.
User list
>> Add the User
You can register a new user with various access rights.
1. Click the [Add] button. User setting dialog is displayed.
2. Enter the new User ID and Password. (Should have a
minimum of 4 characters and preferably a combination
of alphanumeric.)
3. To confirm the password, retype the password that you
typed in the Password box.
4. Select the authority from the drop down list to provide
Operation and settings27
the access rights to each user and then click the [Save] to
confirm your selection.
--
Administrator: Allows you to operate setup menus
and to view live images.
--
Power user: Use of the limited functions of the
system. (The Configuration menu is not allowed.)
A power user can use the Live View, OSD control and
audio functions.
--
Normal user: Provides the lowest level of access,
Allows to view live images only.
--
Custom user: The user can login and view the live
stream image only when the “Enable anonymous
login” option is checked to enable it.
Anonymous
>> Enable anonymous login
Check the box to enable anonymous user login - allows the
user access for only viewing the live stream image.
Maximum RTP stream connection
>> Maximum number of simultaneous stream connection:
Set this number to limit the number of simultaneous stream
connections.
The connections depend on the stream configuration as
shown in the following Maximum RTP stream connection by
stream configuration.
Note:
Video Codec
Resolution
Frame
Rate
Maximum RTP
stream
H.264
1280x1024
30
Up to 10
MJPEG
1280x1024
20
Up to 7
Remember the password.
>> Edit the registered user
You can change the password or authority.
Notes:
1. Choose the user ID and then click the [Edit] button.
2. Change the Password or Authority, then click the [Save]
button to confirm your selection.
>> Delete the registered user
1. Choose the user ID you want to delete.
2. Click the [Remove] button.
Note:
The default administrator user ID ‘admin’ and ‘anonymous’
are permanent and cannot be deleted.
28
•
•
Preview window of the IP device setting and preset
setting are affected by this setting.
•
The video streaming may appear poor at times, this may
be because of the network traffic, too many devices
connected to the switch or hub, enabling motion
detection to each of the video streams and because of
other programs running on your computer.
Save: Click this button to confirm the settings.
Operation and settings
Event settings
the FTP server.
--
Password: Type the password for the folder shared in
the FTP Server.
--
Folder: Type the path with the folder that is shared in
the FTP server.
--
Test: Select [Test] to test the FTP server.
Event Server
Event Servers are used to receive the recorded video clip and/or
notification messages.
3. Click the [Save] button to confirm the settings.
>> To edit the FTP server
1. Choose the FTP server in the FTP server list.
2. Click the [Edit] button.
You can check or edit the FTP server options.
>> To delete the FTP server
1. Choose the FTP server in the FTP server list.
2. Click the [Remove] button. This would remove the FTP
server from the list.
FTP server list
SMTP server list
Image files can be transferred to the FTP server within the scheduled
time. Image file that has been recorded linked to an external event
is sent to the FTP server periodically.
By selecting the e-mail option, a still image of the event is captured
and an e-mail with the attached image file is sent to the specified
mail address.
>> To add the FTP server
>> To add the SMTP server
1. Click the [Add] button. FTP server setting window is
displayed.
1. Click the [Add] button. SMTP server setting window is
displayed.
2. Set the FTP server options.
2. Set the SMTP server options.
--
Alias: Type the FTP Server name to upload the image
files.
--
Address: Enter the FTP server’s IP address.
--
Port: Enter the port number. The default FTP port is
21.
--
User ID: Type the user name for the Folder shared in
--
Alias: Enter the SMTP server name.
--
User ID: Enter the user ID of the SMTP server. This
would be the one who owns the mail account.
--
Password: Enter the password of the SMTP server.
--
Address: Enter the SMTP server address.
Operation and settings29
--
Port: Enter the port number. The default port is 25.
--
Enable SSL: Check when use the SSL (Secure Socket
Layer) protocol. SSL protocol is cryptographic
protocols that provide secure communication on a
network.
--
Receiving address: Type the recipients e-mail address.
You can specify only one recipient e-mail address.
--
Administrator address: Type the e-mail address of the
administrator.
--
Subject: Enter the subject/title of the e-mail.
--
Message: This message can describe the information
of the acquired IP address, etc.
--
Test: Select [Test] to test the SMTP server.
Sensor & Relay (Optional)
Sensor
>> Enable: Marks up when you want to activate the sensor.
>> Alias: Displays the sensor name.
>> Type: Select the sensor type.
3. Click the [Save] button to confirm the settings.
>> To edit the SMTP server
Relay
1. Choose the SMTP server in the SMTP server list.
>> Control duration: Enter the relay time.
2. Click the [Edit] button.
You can check or edit the SMTP server options.
>> Alias: Displays the relay name.
>> Type: Select the relay type.
>> To delete the SMTP server
>> Control relay
1. Choose the SMTP server in the SMTP server list.
2. Click the [Remove] button.
•
30
--
Run: Click to activate the relay.
--
Stop: Click to stop the relay.
Save: Click this button to confirm the settings.
Operation and settings
Motion detect
How to set the motion detect window
1. Click the [Add] button. The motion detect window is
displayed. You can add the five windows maximum for
motion detection area.
2. Set the [Sensitivity] option.
3. Click the edge or corner of the window box to adjust the
window size for motion detection.
4. Click the [Save] button to save the settings.
Notes:
Preview
•
You can reset the window size. Click one of the window edge
or corner and drag & drop to reset the motion detection
area.
•
Motion Detection can be activated when at least one of
channels(HD/SD) is enabled, Video codec is set to H.264 and
GOP size is more than 2.
You can preview the motion detection window on the preview
window.
General
>> Sensitivity: Enter the sensitivity to detect an object in
motion.
>> Save: Click this button to confirm the settings.
Note:
Motion detect function may not normal operate as installation
environment.
Operation and settings31
Smart Analytics (Optional)
Notes:
•
The [Smart Analytics] option is ancillary function and
performance is depends on installation environment or
configuration.
•
SD resolution is changed when you use the Smart Analytics
function.
Intelligent Motion Detection
Detect the motion of object where you set the zone.
Smart Analytics Monitoring
>> Enable : Set to ON or OFF. Setup menu is appeared when
selects ON.
Event
Select the Event. (Intelligent Motion Detection, Streaming Metadata,
Trip Zone, Object Counting) If you choose option, selected option is
activated.
Preview
You can preview the camera image on the preview window.
Notes:
•
Double click the preview screen to maximize full screen.
•
To return to previous screen to double click full screen.
>> Zone: Set the zone.
--
Add
1. Click the [Add] button. When you click on the
preview screen, yellow cross point is displayed.
2. Click again to make another point. The point is
connected as sky blue line from previous point.
32
Operation and settings
3. To complete the zone, move the mouse cursor from
the selected points and click the mouse right button.
Notes:
•
When you select all of point, you can set up to 15
points and area is set automatically.
•
You can cancel the point by click the mouse right
button near the other point.
•
If the path is intersected each other, area setting can
not complete.
•
Up to 4 Zone is available to set.
--
Delete: Delete the selected zone.
--
Delete All: Delete all of the motion area.
Streaming Metadata
Send the VA Metadata where detected zone of the user’s setting for
use from the Client. The camera do not conduct the VA detection.
>> Basic Configuration
--
Sensitivity: Select the sensitivity from drop-down list to
detect an object in motion.
--
Object Size
1. Click the check box of the [Modify] option.
2. The rectangular zone of the maximum and the
minimum object size are displayed.
3. Drag the point of the rectangular zone to adjust the
size.
Notes:
•
•
When you click [Modify], value of maximum and
minimum object size is initialized.
•
Width and Height of zone are displayed as
percentage of the screen automatically.
•
Maximum value is more than minimum value.
Save: Click this button to confirm the settings.
>> Zone: Set the zone.
--
Set
1. Click the [Set] button. When you click on the preview
screen, yellow cross point is displayed.
2. Click again to make another point. The point is
connected as sky blue line from previous point.
Operation and settings33
3. To complete the zone, move the mouse cursor from
the selected points and click the mouse right button.
Notes:
--
•
When you select all of point, you can set up to 15
points and area is set automatically.
•
You can cancel the point by click the mouse right
button near the other point.
•
If the path is intersected each other, area setting can
not complete.
Trip Zone
Detect the direction of object by dividing two of zone.
Delete: Delete the zone.
>> Basic Configuration
--
Sensitivity: Select the sensitivity from drop-down list to
detect an object in motion.
--
Object Size
1. Click the check box of the [Modify] option.
2. The rectangular zone of the maximum and the
minimum object size are displayed.
3. Drag the point of the rectangular zone to adjust the
size.
Notes:
•
•
When you click [Modify], value of maximum and
minimum object size is initialized.
•
Width and Height of zone are displayed as
percentage of the screen automatically.
Save: Click this button to confirm the settings.
>> Zone: Set the zone.
--
Split:
1. Click the [Set1] button. When you click on the
preview screen, yellow cross point is displayed.
34
Operation and settings
Notes:
2. Click again to make another point and the point is
connected as sky blue line from previous point.
•
3. Click the mouse right button to complete the zone.
Notes:
•
You can cancel the point by click the mouse right
button near the other point.
•
If the path is intersected each other, area setting
can not complete.
•
When you click [Modify], value of maximum and
minimum object size is initialized.
• Width and Height of zone are displayed as
percentage of the screen automatically.
Save: Click this button to confirm the settings.
4. Click [Set2] and select side of the previous zone.
5. Repeat the steps 1 to 3 to add other positions.
6. Click [Delete All] to clear all of the area.
--
Directionality: Select the movement direction of object.
Notes:
•
When you select all of point, you can set up to 15
points and area is set automatically.
•
You can cancel the point by click the mouse right
button near the other point.
•
If the path is intersected each other, area setting can
not complete.
>> Basic Configuration
--
Sensitivity: Select the sensitivity from drop-down list to
detect an object in motion.
--
Object Size
1. Click the check box of the [Modify] option.
2. The rectangular zone of the maximum and the
minimum object size are displayed.
3. Drag the point of the rectangular zone to adjust the
size.
Operation and settings35
Object Counting
Detect the direction of object by dividing two of zone. Detect zone
is divided automatically as vertically or horizontally. The number of
detection is displayed on center bottom of the preview screen.
>> Basic Configuration
--
Sensitivity: Select the sensitivity from drop-down list to
detect an object in motion.
--
Object Size
1. Click the check box of the [Modify] option.
2. The rectangular zone of the minimum object size is
displayed.
3. Drag the point of the rectangular zone to adjust the
size.
Notes:
•
•
When you click [Modify], value of minimum object
size is initialized.
•
Width and Height of zone are displayed as
percentage of the screen automatically.
Save: Click this button to confirm the settings.
>> Zone: Set the zone.
-- Split: Select the method of dividing the zone either
vertically or horizontally.
-- Directionality: Select the movement direction of object.
36
Operation and settings
Triggered Event
--
When an event (VA/ Motion detect/ Sensor Event) occurs, this unit
records the live images and routes as configured.
FTP server(JPEG): Sends the JPEG Image to
the FTP server. Image file and suffix setting is
available. You can select Date/Time or Sequence
of Suffix.
•
Stream: Selects the stream of the connected camera.
•
Programmable Alarm (Optional): When the sensor
event is activated, the camera will start the recording
with the setting value of these options. Using this
function, you can get high quality recorded image.
1. Click the check box if you want to activate this
function.
2. Sets the options.
Event schedule list
>> To edit the Event Schedule
1. Select the Trigger event and click the [Edit] button.
Event schedule window is displayed.
2. Set the options.
•
Trigger: Display the selected trigger event and the
current state of trigger. Current state of trigger is
Displayed to On or Off.
•
Time: Sets the weekday, Start, Finish, Pre alarm, Post
alarm and Ignore interval time options.
•
Action: Selects the options. This occurs when the
event runs.
--
FTP server/SMTP server: Uploading of images to
an FTP server, or e-mail notification.
--
Control relay(Optional): The relay is activated or
deactivated.
--
SDCard recording: Record on the SD card when
the event runs.
3. Click the [Save] button to confirm the settings.
Notes:
•
You should register the SMTP and FTP server on the
Event server setting to set this function.
•
Recording of event(VA/Motion detect/Sensor event) runs
every 5 minutes split file.
•
Used stream is profile of Master or HD resolution in case
of FTP(JPEG) transmission.
Operation and settings37
Scheduled Event
Notes:
•
•
You can select through drag of Activation Time table that is
possible to select according to weekday and time.
•
Used stream is profile of Master or HD resolution in case of
FTP(JPEG) transmission. If always checkbox next to FTP(JPEG)
is checked, FTP(JPEG) is always enable regadless of the
activation time.
Save: Click this button to confirm the settings.
Activation Time
>> Always : You can use always by using the FTP server
regardless of activation time.
>> Only scheduled time: Continuously record according to the
set time and the selected weekday.
Action
Set the below option.
>> SD Card recording : Record to SD Card when event occurs.
Selects the camera stream for SD card recording.
>> FTP server(JPEG) : Upload the image or send the e-mail to
the FTP server. Send Image per, Base File Name and Suffix
setting are available.
38
Operation and settings
OSD Menu Setup
3D-DNR
The following table shows the list of menu items and options.
Main
Menu
EXPOSURE
Sub Menu
ELC/ALC,
ALC2
or
ELC
(LND3100
only)
Contents
WDR/BLC
OFF/WDR/BLC/HSBLC
BRIGHTNESS
0 to 100
AGC
SHUTTER
LOW
-
MIDDLE
-
HIGH
-
OFF
0 to 255
OFF/LOW/MIDDLE/HIGH
GREEN
0 to 255
ELC/ALC: x60,...,x2, OFF,
A.FLK, 1/100,...,1/10 000
ALC2: 1/100,..., 1/10 000
BLUE
0 to 255
EXIT
RET/TOP/
END
OFF
AUTO
EXIT
RET/TOP/END
ON
COLOR
TRANSPARENCY
RECTANGLE
0 to 16
MASK
NUMBER
AREA1 to
AREA8
ATW
-
AUTO
-
RECT.
DISPLAY
ON/OFF
AWC/PUSH
-
HEIGHT
4 to 100
COLOR TEMP
INDOOR, OUTDOOR
WIDTH
4 to 100
RED
-100 to 100
MOVE Y
2 to 98
BLUE
-100 to 100
MOVE X
2 to 98
EXIT
RET/TOP/
END
MANUAL
DAY/NIGHT
-
RED
SENS-UP
WHITE BAL
PRIVACY
OFF
AUTO
EXIT
RET/TOP/END
LEVEL
LOW/ MIDDLE/ HIGH
DWELL TIME
5, 10, 15s
EXIT
RET/TOP/END
DAY
-
NIGHT
-
Operation and settings39
PRIVACY
ON
CIRCLE
POLYGON
MASK
NUMBER
AREA1 to
AREA2
CIR. DISPLAY
ON/OFF
HEIGHT
1 to 15
WIDTH
1 to 15
MOVE Y
0 to 100
MOVE X
0 to 100
RADIUS SIZE
0 to 100
EXIT
RET/TOP/
END
MASK
NUMBER
AREA1 to
AREA2
POLY.
DISPLAY
ON/OFF
POLYGON
DRAW
-
POLYGON
MOVE
-
EXIT
RET/TOP/
END
EXIT
SPECIAL
D-ZOOM
WINDOW MOVE
EXIT
SCENE
MODE
(Optional)
RESET
EXIT
40
OFF
IMAGE SIZE
TILT
OFF/ V-FLIP/ MIRROR/ ROTATE
OFF/ ON
IMAGE MOVE
PAN
D-EFFECT
COLOR
ON
RET/TOP/END
ZOOM
0 to 68
PIP
OFF
ON
SHARPNESS
EXIT
STABILIZER
OFF/ ON
USER TITLE
OFF/ ON
LANGUAGE
English
(The option depends on the model.)
EXIT
RET/TOP/END
STD
-
BKLT
-
LOWLIT
-
OUTDOOR
-
INDOOR
-
TRAFFIC
-
USER
-
CAMERA
REBOOT
-
FACTORY
RESET
-
EXIT
RET/TOP/END
-
Operation and settings
General Operation
Notes:
1. Click the [OSD control] button on the LG Smart Web Viewer.
•
button: Used to move upper direction on the menu screen.
2.Click button on the OSD control window.
The camera setting menu appears on the live view window.
•
button: Used to move lower direction on the menu screen.
•
button: Used to increase the value selected in the menu.
•
button: Used to decrease the value selected in the menu.
•
button: Executes selections and displays a submenu for an
item with the mark.
Exposure settings
3.Use or button to select an option then click
Submenu appears.
4.Use
or
button to select a submenu option.
5.Use
or
button to select a value.
button.
6. Select [EXIT] option then click button to exit the setup menu.
In the submenu, use or button to select the [EXIT] then use
or button to select a mode and click button to exit the
setup menu.
--
RET: Return to the previous.
--
TOP: Return to the CAMERA SETTING menu screen.
--
END: Exit the setup menu.
You can set the exposure options using the EXPOSURE menu.
1. Select [EXPOSURE] option on the [CAMERA SETTING] menu.
2. Use
3. Press
or
button to select a mode.
button and the EXPOSURE menu appears.
Notes:
•
ELC Mode is right for outdoor scenes.
•
ALC Mode is right for indoor scenes.
Operation and settings41
WDR/BLC
BRIGHTNESS
Use WDR/BLC option to view the object clearly in backlight
conditions.
You can increase the brightness of the darkened video. If you set the
brightness to lower value, the image gets darkened. If you set the
brightness to higher value, the image gets bright.
1. Select [WDR/BLC] option on the [EXPOSURE] menu.
2.Use
•
or
button to select a mode then click
button.
WDR: WDR (Wide dynamic range) feature can be very helpful
to cope with very challenging lighting conditions. It is
capable of capturing both of the dark part and bright part
and combining the differences into a scene to generate a
highly realistic image as original scene. Set the WDR limit.
2.Use
>> ACE (Adaptive Contrast Enhancement) : This function
is used when you want to display dark areas of WDR
brightly.
1. Select the [AGC] option on the [EXPOSURE] menu.
•
BLC: Camera’s backlight compensation feature helps alleviate
issues of visibility in high contrast areas. Set the BLC limit.
•
HSBLC: Use for masking brightness of the specific area
to view the subject more clearly. The HSBLC mode is
automatically activated only in low luminance scene.
>> AREA SETTING: Use or button to select area then
use or button to select [ON] or [OFF]. Click
button to exit the area setting menu.
>> GRAY SCALE: Use
or
button to select a gray scale.
>> USER SCALE: Use
or
button to select a bright level.
>> MASK: Use or button to select [ON] or [OFF].
If you set the MASK to ON, the mask function is activated
only when the HSBLC is activated by auto mode.
•
42
1. Select [BRIGHTNESS] option on the [EXPOSURE] menu.
or
button to set the bright level.
AGC (Automatic Gain Control)
If the images are too dark, change the maximum [AGC] value to
make the images brighter.
2.Use
or
button to select a mode.
SHUTTER (Shutter Speed)
Select the desired shutter speed for camera exposure. You can
change the shutter speed to higher speed to capture fast-moving
subjects, though the image becomes darker.
1. Select [SHUTTER] option on the [EXPOSURE] menu.
2.Use
or
button to set shutter speed.
Note:
If you set the shutter speed value in ALC2 mode, it is maximum
value. When the camera is activated with ALC2 mode, the shutter
speed is arrived maximum value and then the camera is change to
iris control mode automatically for the camera exposure. Select ALC
mode when flicker is occurred in indoor environment.
OFF: Not in use.
Operation and settings
SENS-UP
White Balance settings
If pictures are not clear due to darkness, this SENS-UP operation
would increase the sensitivity of picture.
Select the method by which the camera shifts its output colors to
compensate for the color of a light source.
1. Select [SENS-UP] option on the [EXPOSURE] menu.
2.Use
•
or
button to select a mode.
AUTO: Adjust the sensitivity of the picture automatically.
>> SENS-UP LIMIT: Use
SENS-UP limit.
or
button to set the
>> EXIT: Select a mode and click
button to exit the menu.
Note:
If you set to [AGC] to [OFF], the [SENS-UP] setting is not available
and [---] mark is displayed.
1. Select the [WHITE BALANCE] option.
2.Use
•
or
button to select a mode then click
button.
ATW (Auto-Tracing White Balance): In this mode, white
balance has better coverage than auto. Proper white balance
may not be obtained under the following conditions:
>> When the scene contains mostly high color temperature
objects, such as a blue sky or sunset.
>> When the scene is dim.
•
AUTO: You can set the white balance options automatically.
•
AWC / PUSH: If you select the AWC / PUSH mode, you will
be able to set up the White Balance automatically using
button.
•
MANUAL: You can set the white balance options manually.
>> COLOR TEMP: Use
or
button to select a function.
--
INDOOR: It is the color temperature range for office.
--
OUTDOOR: It is the color temperature range for
sunlight.
Operation and settings43
>> RED: Set the desired red value.
3D-DNR setting
>> BLUE: Set the desired blue value.
Day/Night settings
1. Select [3D-DNR] option.
If pictures are not clear due to noise, this option would reduce
the noise of picture.
1. Select [DAY/NIGHT] option.
2.Use
2.Use
Notes:
•
or
button to select a mode for DAY/NIGHT function.
AUTO: DAY/NIGHT mode changes automatically.
>> LEVEL: Use
or
>> DWELL TIME: Use
If you set the AGC to [OFF] on the [EXPOSURE] menu,
the [3D-DNR] function is not available and [---] mark is displayed.
•
When you use this function, the afterimage may occur.
button to select a level.
or
button to select a dwell time.
•
DAY: Color mode enabled.
•
NIGHT: Black-and-white mode enabled.
44
button to select an option.
•
Note:
If you set the AGC to [OFF] on the [EXPOSURE] menu, the
AUTO mode of the [DAY/NIGHT] function is not available and
[---] mark is displayed.
or
Operation and settings
Privacy setting
This function is aiming at the protection of personal privacy. The
selected part is not displayed on the screen.
•
--
MOVE Y: Moves vertical position of the mask.
--
MOVE X: Moves horizontal position of the mask.
CIRCLE :
>> Use or
NUMBER].
button to select a mask on the [MASK
>> Use or button to set up the [ON] or [OFF] on the
CIR. DISPLAY option.
>> Use or to select an option then use
to adjust the option.
. The PRIVACY
•
COLOR : You can make any color by adjusting R.G.B LEVEL.
•
TRANSPARENCY : You can adjust the transparency of MASK.
•
RECTANGLE :
>> Use or
NUMBER].
button to select a mask on the [MASK
>> Use or button to set up the [ON] or [OFF] on the
RECT. DISPLAY option.
>> Use or to select an option then use
to adjust the option.
or
button
--
HEIGHT: Increase or decrease the vertical size of the
mask.
--
WIDTH: Increase or decrease the horizontal size of
the mask.
•
button
--
HEIGHT: Increase or decrease the vertical size of the
mask.
--
WIDTH: Increase or decrease the horizontal size of
the mask.
--
MOVE Y: Moves vertical position of the mask.
--
MOVE X: Moves horizontal position of the mask.
--
RADIUS SIZE : You can adjust the RADIUS SIZE.
1. Select the [PRIVACY] option.
2.Use or button to select [ON] and press
SETUP menu appears.
or
POLYGON :
>> Use or
NUMBER].
button to select a mask on the [MASK
>> Use or button to set up the [ON] or [OFF] on the
POLY. DISPLAY option.
>> Use the , , , and buttons to draw the polygon
by moving each vertex on the [POLYGON DRAW]. Each
movable vertex will be displayed as a black square spot
each time you click the button.
>> Use the , , , and buttons to move the
polygon on the [POLYGON MOVE].
Operation and settings45
Special menu settings
D-EFFECT (Digital effect)
You can select the digital effect.
1. Select the [D-EFFECT] option on the [SPECIAL] menu.
2.Use
or
button to select a digital effect.
•
V-FLIP: Flip the picture vertically.
•
MIRROR: Turn on the mirror effect.
•
ROTATE: Rotate the picture. (180°)
•
OFF: Turn off the digital effect.
D-ZOOM
SHARPNESS
You can select the digital zoom level.
The degree to which the boundary of the two portions is clearly
distinguished.
1. Select [D-ZOOM] option on the [SPECIAL] menu.
2. Use or button to select [ON] then click button. When
you set to ON, the displayed image can be shaking.
3. Use or button to select an option then use
to select a level.
or
or
button
button to enlarge the screen.
1. Select the [SHARPNESS] option on the [SPECIAL] menu.
2.Use or button to adjust the option. If you set the
sharpness value to higher, the image outline becomes sharp. If
you set to lower value, the image outline becomes dim.
•
ZOOM: Use
•
PAN: Use
or
button to move the screen. (left or right)
You can switch the displayed picture to gray scale or color.
•
TILT: Use
or
button to move the screen. (up or down)
1. Select the [COLOR] option on the [SPECIAL] menu.
COLOR
2.Use
46
or
button to change a color effect.
•
ON: To display the picture with color.
•
OFF: To display the picture with gray scale.
Operation and settings
PIP
USER TITLE
You can view an image in PIP(picture in picture) mode.
You can use the camera identification to assign a number and
character to the camera.
To disappear the user title, select [OFF].
1. Select the [PIP] option on the [SPECIAL] menu.
2.Use or button to select [ON] then click
window is displayed on the live window.
button. The PIP
•
WINDOW MOVE : The PIP window can be moved through the
live image window using , , and buttons.
•
IMAGE MOVE : You can view the special area image on the
PIP window. Use , , or button to view the live
image of the special area.
•
IMAGE SIZE: Use or button to enlarge or reduce the size
of image on the PIP window. This function is activated with
digital zoom function.
1. Select the [USER TITLE] option on the [SPECIAL] screen.
2.Use or button to select [ON] then click
TITLE menu appears.
button. The USER
A
STABILIZER
The image stabilizer function minimizes the appearance of shaky
images caused by low-frequency vibration. This function is useful for
outdoor surveillance.
Select the [STABILIZER] option and set to ON or OFF.
Note:
If you set the [STABILIZER] to ON, the Digital zoom is set to [x1.1]
automatically.
3.Use , , or
click button.
button to select a character or number then
•
CLR: Clear all entered characters and numbers.
•
POS: Move the USER TITLE position on the screen using the
arrow buttons.
•
END: Confirm your selection or exit the setting.
•
A(Blank): Insert a space at the cursor position.
•
/
: Moves cursor to left or right.
LANGUAGE
Select the viewer language for the camera setup menu and OSD
information display.
1. Select the [LANGUAGE] option on the [SPECIAL] screen.
2.Use
or
button to select the language.
Operation and settings47
SCENE mode setting (Optional)
Notes:
You can set value installed camera environment properly using this
function. Several configuration value is set automatically to select
option.
•
•
STD: Settings general environment .
•
BKLT: WDR set automatically to see the subject clearly under the
backlight condition.
•
LOWLIT: Increase the Gain and set SENS-UP function to see the
subject clearly under the low light condition.
•
OUTDOOR: Change to the ELC mode not to decrease definition
under too light condition. And decrease Brightness value slightly
prevent to video of supererogation.
•
INDOOR: Condition of light set automatically to match indoor
environment.
•
TRAFFIC: Set shutter speed fast to apprehend traffic information
and status.
•
USER: If user change each value of function, save the changes.
48
Set each value of option as selected option on the [SCENE
MODE] like as below table.
OPTION
Shutter
speed
AGC
White
Balance
WDR/BLC
3D-DNR
DAY/NIGHT
ACE
SHARPNESS
BRIGHTNESS
SENS-UP
EXPOSURE
STD
BKLT
LOWLIT
OUTDOOR
AUTO
AUTO
AUTO
AUTO
MIDDLE
MIDDLE
HIGH
MIDDLE
ATW
ATW
ATW
ATW
OFF
MIDDLE
AUTO
34
50
OFF
ALC2
WDR
MIDDLE
AUTO
OFF
34
50
OFF
ALC2
OFF
MIDDLE
AUTO
34
50
AUTO x10
ALC
OFF
MIDDLE
AUTO
34
45
OFF
ALC2
Operation and settings
OPTION
Shutter speed
AGC
INDOOR
AUTO
MIDDLE
TRAFFIC
Manual(1/120)
HIGH
USER
-
White Balance
Manual (Indoor)
ATW
-
WDR/BLC
OFF
OFF
3D-DNR
MIDDLE
MIDDLE
DAY/NIGHT
AUTO
AUTO
ACE
SHARPNESS
34
34
BRIGHTNESS
50
50
SENS-UP
OFF
OFF
EXPOSURE
ALC
ALC
• Value of [SCENE MODE] is not initialized even the reboot system.
If you set to [STD], the default value of [SCENE MODE], run
factory reset.
•
If you use not DC Iris lens but Manual Iris lens, must set ELC
mode on the [EXPOSURE] option. In this case, value of [SCENE
MODE] set to [USER] automatically.
Reset setting
1. Select the [RESET] option.
2.Click
3.Use
button and the RESET menu appears.
or
button to select option.
•
CAMERA REBOOT: Reboot the camera system.
•
FACTORY RESET: Clear certain settings and information and
return to factory default settings.
4.Click
button to confirm your selection.
Operation and settings49
Reference
Troubleshooting
This section provides useful information to help you to resolve any difficulty you might have with your LG IP device. Fault symptoms,
possible causes and remedial actions are provided here.
IP Setting problems
•
ARP/Ping: Disconnect and reconnect the power to the network camera. The device should get the IP within 2 minutes.
•
Ping your camera: Open the command prompt on your computer, type ping with the IP address of the network device. The reply
obtained by this command provides explanation for the cause of the problem.
1. bytes = 32 time = 2 ms indicates that the IP address is already used and cannot reuse the same. A new IP address needs to be
obtained.
2. Destination host unreachable: indicates that the network device and your computer do not fall in the same subnet hence needs to
get a new IP address. Contact the system administrator for the required help.
3. Request timed out: Indicates that the IP is free as it is not used by anyone and the network device can obtain this.
•
IP Conflicts: If the LG network device is set with a static IP address and if the DHCP option is set then there may be IP’s same as the
network device and other network partner. Hence set the static IP address to 0.0.0.0 to resolve this conflict.
Cannot access the camera from browser:
•
Reconnect the network camera with power and check the ping operation to know if the IP is used by others.
•
Disable the proxy setting in the Browser if you are using a proxy server.
•
Check for proper cabling and network connections, try to ping after verifying the connectivity.
•
Sometimes when HTTPS is enabled, we would be checking the URL with http, in this case manually change the URL to the http/https
accordingly.
•
Verify the DNS and Gateway settings if the IP address is assigned statically to the network device.
50
Reference
Accessing camera external to the local network
•
Firewall Protection: Check for the internet firewall with the system administrator, either he has to do port forwarding or modify the DMZ
function on the router.
•
Default router needed: Check if you need configure the router settings.
Sporadic network performance
•
Network Switches or hubs used may be of the lower configuration and the load on this may not meet the required conditions of our
network camera.
•
Check for the RJ-45 cables that are used for the network connectivity.
•
If POE is used check if the power is got by the network camera when connected to it.
Login Password lost
•
Reset the camera by pressing the Reset button for more than 3 seconds to restore default settings.
•
After the factory settings login using the default user name and password.
Video Streaming problems
•
If the video streaming does not start on the Web browser, install the LG Web Client ActiveX program on your computer following the
instructions on the Web browser.
•
When Windows IE browsers are used always take care to allow pop ups, check this option before we run the web client.
•
Check the quality of image by referring the video settings as described in the manual.
•
Sometimes there would be intermittent or very slow video streaming, this may be because of the higher resolution and frame rate that
are set for the video.
•
The video streaming may appear poor at times, this may be because of the network traffic ,too many devices connected to the switch or
hub, enabling motion detection to each of the video streams and because of other programs running on your computer.
•
If the images appear to be blurred adjust the focus of the network camera to get a clear image.
•
Video images if appear white and black adjust the settings in the OSD to get back the colorful image.
•
Select the Night mode if the network camera is connected at a place where surrounding light is less or dark.
Reference51
•
If we obtain lower frame rate than set we need to check from the system administrator for sufficient bandwidth available or reduce the
number of applications running on the client computer.
•
If the client PC’s are unable to access the multicast stream, check with the system administrator for the use of a valid multicast address or
check if the router is supporting multicasting.
•
If the images appear to have white of gray stripes on it, upgrade the Video graphics driver on the client PC to the latest version.
•
Video images may be noisy if you are using the camera in a very low light environment or the bit rate/quality is set to very low values.
Provide higher values for quality and support the surrounding environment with enough light.
Audio condition
The client computer that is interacting with the camera needs to have a sound card that is functional to support speaker and microphone.
The sound card needs to be checked for its support for full duplex communication.
Ensure that the mute button of the client computer is not set and all the audio settings are correct.
Speaker button on the web viewer should be enabled to listen the audio from the network camera.
Ensure that the bidirectional audio button is enabled on the Web viewer and the microphone is set.
Change the input and the output gain for microphone and the speaker respectively to set correct audio level.
Clear browser’s Cache
•
If your browser is not working correctly after upgrade firmware. Please follow the below solution.
•
Solution: Deleting your browser’s cache may be resolved this issue.
1. Open Internet Options in browser Tools menu and click the [Delete Files] button in the second entry (Internet temporary files).
2. Check the other settings that should not be changed.
RCA output problem
•
RCA output use to initial installation.
•
Depending on the IP Camera usage scenario, RCA output video may not be smooth. It is used for initial installation only.
52
Reference
BNC output usage
BNC connector is for convenience of camera installation, and it is not suited to surveillance.
For all further support please contact the supplier or forums or websites.
Open source software notice
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://
opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available
for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such
distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is valid for three (3)
years from the date on which you purchased the product.
Reference53
Specifications
Item
LNB5100
LND5100
Image Device
6.08 mm (1/3 type) Progressive Scan CMOS (1.3 Mega Pixels)
Lens Type
DC-Iris, CS Mountable (Optimization of
6.08 mm (1/3 type) Lens of 1.3 Mega Pixels or
above)
Day/Night
ICR
Minimum
Illumination
Color
0.3 lx (F1.2, Gain : High)
B/W
0.005 lx (F1.2, Gain : High)
LNV5100
2.8 mm to 10 mm F1.2
WDR
Support
Image Enhancement
Backlight Compensation, 2D+3D-DNR, Exposure Control, Sens Up Control, AGC, White
Balance, Privacy Masking, EIS, Sharpness, Digital Zoom, Scene mode
Resolution (Maximum)
Up to 1 280 x 1 024
Output
RJ-45 (Network), RCA (Installation)
Frame Rate (Maximum)
30 fps @ 1280 x 1024, 30 fps @ 720p
Compression
H.264_HIGH, H.264, MJPEG
Multi-Streaming
Dynamic Profile (Up to 7)
Audio In/Out
1/1
Audio Compression
G.711, G.726
2-way Audio
Support
SD Slot
micro SD
EVENT
54
Alarm In/Out
1/1
Motion detection
Support
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Reference
VA
Intelligent Motion Detection
Support
Streaming Metadata
Support
Trip Zone
Support
Object Counting
Support
Integrated Client
LVi510
Remote S/W
LVi510, Mobile application (iPhone, Android, iPad)
Connections
Up to 10
Security
Password Protection, HTTPS(SSL, TLS)
Ethernet
10/100 Ethernet
Protocol
IPv4 and IPv6
TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP
IPv4
FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
Open Protocol
ONVIF 2.2 Profile S,PSIA 1.1
Operation Temperature/Humidity
-10 ºC to 50 ºC / 0 % RH to 80 % RH
Power Source
PoE (IEEE 802.3af ), DC 12 V (±20 %)
Power Consumption
5.9 W
Input current
Maximum 440 mA (DC 12 V), Maximum 140 mA (PoE)
Dimension
68.6 mm x 54.0 mm x 121.5 mm (W x H x D)
140 mm x 120 mm
(Ø x H)
140 mm x 122 mm
(Ø x H)
Weight
365 g
610 g
964 g
Reference55
Item
LNB3100
LND3100
Image Device
6.08 mm (1/3 type) Progressive Scan CMOS (1.3 Mega Pixels)
Lens Type
DC-Iris, CS Mountable (Optimization of
6.08 mm (1/3 type) Lens of 1.3 Mega Pixels
or above)
Day/Night
Digital
Minimum Illumination
0.3 lx (F1.2, Gain : High)
WDR
Support
Image Enhancement
Backlight Compensation, 2D+3D-DNR, Exposure Control, Sens Up Control, AGC, White
Balance, Privacy Masking, EIS, Sharpness, Digital Zoom
Resolution (Maximum)
Up to 1 280 x 1 024
Output
RJ-45 (Network), RCA (Installation)
Frame Rate (Maximum)
30 fps @ 1280 x 1024, 30 fps @ 720p
Compression
H.264_HIGH, H.264, MJPEG
Multi-Streaming
Dynamic Profile (Up to 7)
SD Slot
micro SD (Optional)
EVENT
Motion detection
Support
Event Notification
Email, FTP
Pre Event Buffering
Support
3 mm F2.0
0.7 lx (F2.0, Gain : High)
Integrated Client
LVi510
Remote S/W
LVi510, Mobile application (iPhone, Android, iPad)
Connections
Up to 10
Security
Password Protection, HTTPS(SSL, TLS)
Ethernet
10/100 Ethernet
56
Reference
Protocol
IPv4 and IPv6
TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP
IPv4
FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
Open Protocol
ONVIF 2.2 Profile S,PSIA 1.1
Operation Temperature/Humidity
-10 ºC to 50 ºC / 0 % RH to 80 % RH
Power Source
PoE (IEEE 802.3af ), DC 12 V (±20 %)
Power Consumption
5.9 W
Input current
Maximum 440 mA (DC 12 V), Maximum 140 mA (PoE)
Dimension
68.6 mm x 54.0 mm x 121.5 mm (W x H x D)
140 mm x 110 mm (Ø x H)
Weight
357 g
506 g
Reference57
Download PDF

advertising