LG | LNB5100 | LG LNB5100 Owner’s Manual

OWNER'S MANUAL
High Definition Network Camera
Please read this manual carefully before operating your set and retain it for future reference.
MODEL
LNB5100/LNB3100 series
LND5100/LND3100 series
LNV5100 series
LNU5100R series
LND5100R/LNV5100R series
LND7300/LNV7300 series
1410 (V2.1)
Contents
Introduction.................................................................................... 3
Reference...................................................................................... 46
Troubleshooting..................................................................................46
Operation and settings.................................................................. 4
Open source software notice..........................................................49
Before using the system......................................................................4
Specifications.......................................................................................50
Recommended PC Requirements....................................................4
Accessing the LG IP device.................................................................5
LG Smart Web Viewer Overview.......................................................6
Configuration menu overview...........................................9
Configuring the LG Network Camera Device...............................9
Accessing the Configuration menu..................................9
System settings.....................................................................10
Audio & Video settings.......................................................17
Network settings..................................................................27
User settings..........................................................................34
Event settings........................................................................36
2
Introduction
The LG Network Camera is designed to use on an Ethernet network and must be assigned an IP address to make it accessible.
This manual contains instructions on how to install and manage the LG Network Camera in your networking environment. Some knowledge
of networking environments would be beneficial to the reader.
Note that design and specification of this unit may differ from the manual as quality improvement. Should you require any technical
assistance, please contact authorized service center.
Features Chart
This table shows the differences between the models.
Item
LNB5100
LND5100
LNB3100
LND3100
LNV5100
VA
Yes
Yes
No
No
Yes
Audio
Yes
Yes
No
No
Yes
Sensor&Relay
Yes
Yes
No
No
Yes
Item
LNU5100R LND5100R LNV5100R
LNV7300
LND7300
VA
Yes
Yes
Yes
Yes
Yes
Audio
Yes
Yes
Yes
Yes
Yes
Sensor&Relay
Yes
Yes
Yes
Yes
Yes
Introduction3
Operation and settings
Before using the system
Recommended PC Requirements
•
Before using the LG IP device make sure the connections are
correct and verify whether proper power supply is used.
The LG IP device can be used with most standard operating systems
and browsers.
•
Check the connections of the LG IP device for the correct
conditions.
•
Check that the LG IP device is(are) connected to the network and
that power is supplied.
•
Once the connections are made you need to install the LG client
program to the PC from which you want to access the device.
The LG Smart Web Viewer program is automatically installed
when you connect the LG IP device.
The LVi510 and the LG Smart Web Viewer program are the
network program of the LG Video Server and the LG IP cameras.
•
To view streaming video in Internet Explorer, set your browser
to allow ActiveX controls. If you find this message “This website
wants to install the following add-on: ‘IPCam_Streamer.cab’ from
‘LG ELECTRONICS INC’”, Click the yellow bar and install LG Smart
Web Viewer Program on your computer. Please set your browser
zoom level to 100%.
•
The Layouts and the Live view pages may differ with different OS
(Operating Systems) and Web Browsers.
•
Care needs to be taken not to run any other applications when
the Client Program is running as it may cause memory shortage.
4
Items
Operating System
Requirements
Windows XP Professional,
Windows VISTA, Windows 7
CPU
Intel Core2 Quard Q6700 (2.66 GHz) or
above
Web Browser
Microsoft Internet Explorer above the
version 7.0 and below the version 9.0.
DirectX
DirectX 9.0c (Windows XP), DirectX 11
(Windows VISTA, Windows 7) or above
Memory
2 GB or above RAM
Graphics Card
Resolution
256 MB or above Video RAM
2 048 x 1 536 (with 32 bit color) or higher
Operation and settings
Accessing the LG IP device
default administrator user name and password are
“admin”.)
You can access the LG IP device by following the below steps.
1.
Default password must be changed for security after
initial connection.
Install LVi510 Program
It recommended to use LVi510 surely.
2.
Note:
Discover the LG IP device using the IP Utility
The IP Utility can automatically discover and display LG IP
devices on your network.
3.4 Note:
•
The IP Utility shows the MAC address, IP address, Model
name and so on.
3.2 Enter the IP address of the LG IP device in the address
bar of the browse.
The computer running the IP Utility must be on the same
network segment (physical subnet) as the LG IP device.
3.
Run the IP Utility program.
2.2 Click the [Search] button or select the [Search] option
in the Device search menu.
After a few seconds the found LG IP devices gets displayed in the IP Utility window.
3.3 Enter the user name and password set by the
administrator.
3.4 Click the [OK] button and then the LG Smart Web
Viewer is displayed in your browser.
•
The LG Smart Web Viewer needs more time to display it
according to the network conditions.
•
If the login window is not displayed, check the pop-up
blocker. If you set the pop-up blocker, the login window
is not displayed. You must allow the pop-ups.
•
If you connect the LG Smart Web Viewer for the first time,
the Security Warning window is displayed to install the
LG Smart Web Viewer program. You must install the LG
Smart Web Viewer program for using the LG IP device.
•
If your computer or network is protected by a proxy or
firewall, the proxy or firewall settings can prevent the LG
Smart Web Viewer program. Change the proxy or firewall
settings to activate the LG Smart Web Viewer program.
Logging in to the LG Smart Web Viewer
3.1
Run the IP Utility and find the LG IP devices.
3.2
When the LG IP devices appear in the IP Utility
window, double-click IP address or right click on the
same IP address and select “Connect to Web Page”
to start the LG Smart Web Viewer. When accessing
the LG Smart Web Viewer, the authentication dialog
appears on the screen.
3.3
Enter the user name and password. (Note that the
You can also access the LG Smart Web Viewer as shown
below.
3.1 Start your Web browser.
Note:
2.1
Click the [OK] button and then the LG Smart Web
Viewer is displayed in your browser.
Operation and settings5
LG Smart Web Viewer Overview
Item
Description
Select the video image size from the
drop-down list.
The initial view size is set to D1.
(FULL SCREEN / AUTO RESIZE /
1280 x 1024 / D1 / CIF)
Note:
Note:
The language displayed on the screen may differ by models.
•
Select [FULL SCREEN] to enlarge full
screen of monitor. To return previous
screen, press ESC key or double click.
•
When you select [AUTO RESIZE], size
of live view screen fit to window.
Ratio imaging is fixed by width
based.
It displays Video Codec, Resolution and
FPS of the selected video stream.
Check this option as the network
connection type (TCP or UDP). If you
check it, the client connects to the server
using TCP connection.
Select buffering time of live stream.
6
Operation and settings
Click to display the check box of
[Hostname], [Framerate] and [Bitrate]
options. [Display] is displayed on left
top of the live view window in order of
selecting options.
Video Analysis
>> Hide: Video Analysis display
function is not in use.
>> SVA: Displays the Smart Video
Analysis function to the live view
window.
>> MD: Displays the Motion
Detection function to the live
view window.
Note:
When you use the DPTZ function, all
of Display function is deactivated for
a while.
Click to effect and then check the check
box of [Edge Enhancement] option. The
user gets more sharp reception on the
live view window.
Note:
This feature only affects the live view
window.
Click to save the current image in JPEG
format on your computer.
1. Click the [Snapshot] button and then
the Snapshot window is displayed.
2. Click the [Save] button in the
Snapshot window.
3. Enter the file name (JPEG format) and
select the folder to save it.
4. Click the [Save] button to confirm it.
5. Click the [Close] button in the
Snapshot window to close it.
Select the video stream. From the Live
view drop-down list, select the desired
video image source.
Note:
You can set the stream configurations
independently. This would facilitate the
user to set the live view at his comfort.
Provides all the necessary tools
for setting up the device to your
requirements. The user will need
administrator level to do this.
Note:
If you want to exit the Configuration
menu, select one of the video stream in
the Live view drop-down list.
Operation and settings7
Displays the current surveillance live
screen. You can monitor the camera
image on the live view window of the LG
Smart Web Viewer.
Click this button and drag the area to
use digital PTZ function. Right-clicking
the screen will bring up the previous
magnification.
(Color icon: On, Gray scale icon: Off.)
1. Click this button to open the folder
browse window. Click the button
again in next time, video is recorded
automatically without selection of
folder.
Click this button to connect or
disconnect the audio communication
between the LG IP device and the
connected PC. The option depends on
the model.
(Color icon: On, Gray scale icon: Off.)
Click this button to switch the
microphone off and on for the computer.
The option depends on the model.
(Color icon: On, Gray scale icon: Off.)
Click this button to switch the sound off
and on, for the speaker of the computer.
The option depends on the model.
(Color icon: On, Gray scale icon: Off.)
Note:
If you want to change the folder,
move to other pages or press the
refresh button.
2. Recording button is activated and
recording will be started.
Note:
If recording exceed the time(1 hour)
or size limit (1 GB), recording is
stopped automatically with warning.
3. To stop the recording, click this
button during the recording.
8
Operation and settings
Configuration menu overview
Event server
The following table shows the list of menu items.
Sensor & Relay
The configuration images are different from each model.
Main Menu
Sub Menu
Note
Triggered Event
Date & Time
Scheduled Event
Storage
Option
Text Overlay
Option
Language
Stream
Basic
RTP stream
TCP/IP
DDNS
Network
IP filtering
Configuring the LG Network Camera
Device
Only administrator-level users have permission to access the
Configuration menu.
Camera
Audio
Option
The features and options of the LG IP camera are configured
through the Configuration menu.
Log & Report
Audio & Video
Motion detect
Smart analytics
Version
Maintenance
System
Event
Option
Option
Accessing the Configuration menu
Click the [Configuration] button to display the LG Smart Web Viewer
configuration window.
Warning
The Configuration setup should be made by qualified service
personnel or system installers.
SNMP
QoS
802.1x
SIP
User
Basic
Operation and settings9
System settings
Time zone
Version
Set the time difference from GMT in the area where the IP device
is installed. Select the time zone in the area where the IP device is
installed from the drop down list.
Displays the current Model Name and Software version.
Time mode
>> Synchronize with NTP Server: Select if you want to
synchronize the IP device’s date and time with those of the
time server called NTP (Network Time Protocol). Specify the
NTP server’s name. Click the [Test] button for connection test
to the server.
>> Synchronize with personal computer: Select if you want
to synchronize the IP device’s date and time with your
computer.
>> Synchronize manually: Select if you want to set the IP
device’s date and time manually. Select the year, month and
date by clicking the calendar button. Set hour, minutes and
seconds in the edit boxes.
Date & Time
Note:
•
When system reboot after time setting, time of system
could be delayed. If you set the time correctly, set the
[Synchronize with NTP server] option.
•
Refer to NTP configuration as operation system of
the Recording Server when the Recording Server use
recording function and NTP server.
Server time
>> Server time: Displays the current date and time of the IP
device.
•
10
Save: Click this button to confirm the settings.
Operation and settings
Maintenance
Note:
Backup and Restore can happen on IP device having the
same version of firmware. This feature is not intended for
multi-configurations or for firmware upgrades.
Firmware
>> Upgrade
1. Click the [Browse] button.
2. Find and open the firmware file.
3. Click the [Upgrade] button to update the firmware.
Note:
System reboot
When you upgrade the system, it may take some minutes
to be done. Do not close the browser while the upgrade
is in progress. If you close the browser, it may cause a
malfunction. You should wait until the confirmation window
is displayed. When the upgrade is finished, the confirmation
window will be displayed.
Click the [Reboot] button to restart the IP device. It takes some
minutes for the IP device to start again.
Backup and restore
>> Backup: To take a backup all of the settings. If necessary, it
make possible to return to a backup configuration.
1. Click the [Backup] button.
2. Click the [Save] button.
3. Follow the instructions on the browser to specify the
folder.
4. Click the [Save] button to save the settings.
>> Restore:
>> Initialize: The [Initialize] button should be used with caution.
Clicking it will return all of the IP device’s settings to the
factory default values. Except for the Network settings, PTZ
Protocol and Preset settings. (The option depends on the
model.)
Note:
Refer the “Clear browser’s cache” of Troubleshooting.
1. Click the [Browse] button.
2. Find and open the file in which the configuration setting
data is stored.
3. Click the [Restore] button and the system settings will be
restored and reboot the system.
Operation and settings11
Storage (Optional)
>> Set as NTP server IP: Click this button to use the entered
Recording Server IP as the NTP server IP.
Note:
•
The recorded file name is made automatically as the
“[Created date of the file]_[GMT Recording Time].DAT”
type.
•
If the capacity of the SD card remains less than 200 MB,
stop recording or overwrite new file after delete old one
as [Overwrite] setting. The overwritten file can not play
or may malfunction when you download.
•
Recorded file on the SD card, is recording 1 frame per
second when set video codec to MJPEG.
Device Management
Note:
SD Card function may not be supported in specific countries.
General
>> Overwrite: If the micro SD card has insufficient space and
this option will be activated. It will overwrite the oldest data.
>> DiskFull Notification: Sends an warning e-mail to the SMTP
server when the micro SD card has fully recorded. Select the
SMTP server from the drop-down list. You should register the
SMTP server on the Event server setting to set this function.
>> Network Failure Recording: Select the check box to activate
the micro SD card recording function. If the system does
not work with recording server, the system will record the
data to the micro SD Card. When the system connect to the
recording server again, the recorded data of the micro SD
card will transfer to the recording server automatically.
>> Using the micro SD card
1. Insert the micro SD card carefully to the micro SD card
slot of the camera.
2. Click the [Mount] button. If the micro SD card is mounted
to the system correctly, the [Mount] button will be
changed to the [Unmount] button.
3. Displays the information of the[Disk ID], [Status],
[Capacity] options.
Note:
•
When the micro SD card is mounted, you should format
the micro SD card. After the micro SD card format is
finished, you should click the [Mount] button to use it.
•
When you use the micro SD card format function, it may
not progress immediately. In this case, you should try it
again after waiting a few minutes.
>> Recording Server IP: Enter the recording server IP.
12
Operation and settings
>> Remove the micro SD card
1. Click the [Unmount] button. If the micro SD card is
unmounted from the system correctly, the [Unmount]
button will be changed to the [Mount] button.
File Management
Displays the recorded file of the micro SD card on the list. Click the
[Search] button to display the recorded file. The list will be updated
when you click the [Search] button.
2. Remove the micro SD card from the micro SD card slot of
the camera.
>> To view the recorded file of the micro SD card
1. Select the search option.
Note:
When you use the Unmount function, it may not progress
immediately. Operations such as recording of the system and
reading of data are required stop time before the Unmount
function is activated. You should try it again after waiting a
few minutes.
--
Some: You can set the search condition by using the
date and time options.
>> Download: You can download the recorded data of the
list to your PC. Select a recorded file on the list and click
the [Download] button. The two confirmation window
is displayed. You should download the all files that the
recorded file(*.DAT) and information file(*.INFO). You can
download as AVI file according to File format.
>> File Format: You can selects the Recording File Format(AVI
or DAT). Recording, Search and Download are available
according to the setting.
Note:
•
All: Search the all recorded files in the micro SD card.
2. Click the [Search] button and then the search result is
displayed on the list.
File Format
•
--
Note:
SD Recording or FTP(Video) Sending Format are set
according to the setting. When you select to AVI, [Auto
Recording function] may not be activated in case of
network error.
IP Camera’s time will be appeared in players based on
DirectShow such as Windows Media Player and MPlayer.
•
It is recommended to deactivate the [Overwrite] function
before you download the file. When [Overwrite] function
is activated, the downloading file might be overwritten,
if the micro SD card has insufficient space.
•
The downloaded file can be played by using the LG File
player.
>> Remove: Delete file from the SD card.
•
Save: Click this button to confirm the settings.
Operation and settings13
Text Overlay
Text Overlay (Optional)
Text Overlay
>> Enable: Set to ON or OFF. Setup menu is appeared when
selects ON.
>> Date & Time : Select the ON to display time and date of
Client PC.
>> Channel Name: Enter the channel name you want to use.
You type the Channel Name, it will be displayed whether you
select the ON or OFF.
>> Flickering: Set to On or OFF.
>> Position: You can designate the position of text from drop
down list.
•
Save: Click this button to confirm the settings.
Note:
The text overlay option may differ in method as to model and
version.
Note:
Preview
The text settings on [Text Overlay] is preserved, even though
initialize the camera from [Maintenance] or [Factory Reset].
You can preview the camera image on the preview window.
You can change the text settings on [Text Overlay] directly.
Mode
>> Normal Mode: Follow the normal procedure of text overlay
option by selecting the [Normal Mode].
>> Multiline Mode: Set more characters, color and size of the
text overlay by selecting the [Multiline Mode]. The saved text
overlay is displayed on the left top of screen.
14
Operation and settings
Basic Configuration
When you select the [Normal Mode], you can adjust the
[Date&Time], the [Text Information], the [X position], the [Y position]
and the [User Title] function. And other functions are able to adjust
by selecting the [Multiline Mode].
>> Date&Time: Click the check box of [Date&Time] to display
time and date of Client PC.
>> Text Information: Enter characters in the text field. (From
[Text1] to [Text4]) Maximum input characters are depends
on the resolution.
--
LNB5100/LNB3100/LND5100(R)/LND3100/LNV5100(R)/
LUN5100R series
>> Multi-Line Text: Enter characters in the text field. Maximum
input characters are depends on the resolution.
--
LNB5100/LNB3100/LND5100(R)/LND3100/LNV5100(R)/
LUN5100R series
CaptureMode
Column
Row
Capture Mode
16:9
24
12
Font Size
Column
Row
Column
Row
4:3 or 5:4
24
16
0
32
12
32
16
1
32
12
32
16
--
LNV7300/LND7300 series
16:9
4:3 or 5:4
CaptureMode
Column
Row
2
24
12
24
16
16:9
27
13
3
18
9
18
12
4:3 or 5:4
27
16
>> X Position: Set the horizontal position of each text overlay.
>> Y Position: Set the vertical position of each text overlay.
>> User Title: Enter the user title. The user title is displayed on
the right bottom of screen.
Operation and settings15
--
Log & Report
LNV7300/LND7300 series
Capture Mode
16:9
4:3 or 5:4
Font Size
Column
Row
Column
Row
0
32
16
32
16
1
32
16
32
16
2
32
16
32
16
3
27
13
27
16
>> Color: You can make any color by adjusting R.G.B LEVEL.
>> Size: You can adjust the font size.
Note:
•
If you change the [CaptureMode], the existing characters
may not be seen partially.
•
The [Multi-Line Text] is an one off feature. When refresh a
browser to connect this option again, the text input field of
[Multi-Line Text] is cleared but contents of text overlay are
remained on a live view screen.
•
•
If you use below features, text overlay is changed [Normal
Mode]
: [System>Maintenance>Reboot], [OSD Control>Reset],
[Audio & Video>Camera>CaptureMode]
Save: Click this button to confirm the settings.
16
Log & Report status
The System log provides a summary of the status of the IP device.
The unit records the data of the software activity in a file.
>> View Log: Click this button to display the system log
information.
--
Download: Click this button to see the log information of
system.
>> View report: Click this button to display the report of the
system.
--
Download: Click this button to see the report
information of system.
Note:
The downloaded file is a UNIX type. If you open the file in Microsoft
Note pad, it will display the text as if the file contained no line
breaks at all.
Operation and settings
Language
Audio & Video settings
Camera
Language list
Select a language for the LG Smart Web Viewer configuration menu
and information display.
Note:
The language options may differ depending on models.
•
Save: Click this button to confirm the settings.
Note:
The option depends on the model. This table shows the differences
between the models.
Operation and settings17
LNB3100,
LND3100
LNU5100R,
LND5100R,
LNV5100R
LNV7300,
LND7300
Yes
Yes
Yes
No
Yes
No
Yes
Yes
Yes
No
ITEM
LNB5100,
LND5100
ALC
Yes
ELC
ABF
Scene Mode
Flickerless
Max Shutter,
Sens-Up
Limit
SmartIR
D-Zoom
D-Effect
Stabilizer
Note:
Yes
No
Yes
No
Yes
(LNB3100
only)
Yes
No
No
Yes
x 60
x 60
x 60
x 64
No
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
If the video image size is 4:3 or 5:4 mode, the D-Zoom, D-Effect,
and Stabilizer function is not activated for LNV7300 and LND7300
models.
18
Preview
You can preview the camera image on the preview window.
General
>> Contrast: Edit the contrast value from 0 to 100. Selecting 100
provides the image with the highest contrast.
>> Standard: Displays the video standard of the camera.
>> CaptureMode: Select the capture mode.
Note:
If you change the CaptureMode option, the Privacy, WDR/
BLC and HSBLC settings on the OSD menu are initialized.
>> Sensor Framerate (Optional): You can select the Sensor
Framerate value between 30 and 25.
Note:
• It is recommended to select Sensor Framerate value to
30 in 60 Hz region, 25 in 50 Hz region to reduce flicker.
• Maximum FPS is set 25 when you select Sensor
Framerate value 25.
• Save: Click this button to confirm the settings.
Note:
The Capture mode and Sensor Framerate are not initialized.
Operation and settings
Focus (Optional)
>> ABF Mode: Click the [ABF Push] or [MANUAL] button.
-- ABF Push: This function will be activated automatically to
adjust the back focus.
-- MANUAL: Use [Near ] or [Far ] button to adjust the
focus.
>> Day/Night ABF: You can set the Day&Night function with ABF
function.
-- ON: If you set to On, the ABF function will be activated
automatically when the D/N function is activated.
-- OFF: Not used.
• Focus Reset: Return to factory default settings.
Note:
Some values you have set may not be applied, while the ABF
function is running. Please set the values after the ABF function is
finished.
Exposure (Optional)
>> Mode: Select [Mode] option on the [Exposure] menu, then
select a value.
>> WDR/BLC: Use WDR/BLC option to view the object clearly
in backlight conditions. Select [WDR/BLC] option on the
[Exposure] menu.
-- WDR: WDR (Wide dynamic range) feature can be very
helpful to cope with very challenging lighting conditions.
It is capable of capturing both of the dark part and
bright part and combining the differences into a scene
to generate a highly realistic image as original scene.
-- BLC: Camera’s backlight compensation feature helps
alleviate issues of visibility in high contrast areas.
Operation and settings19
--
>>
>>
>>
>>
20
HSBLC: Use for masking brightness of the specific area to
view the subject more clearly.
>> AREA SETTING: Click the [Show] button to select area.
>> GRAY SCALE: Select a gray scale.
>> USER SCALE: Set a bright level.
>> MASK: Select [On] or [Off ]. If you set the MASK to ON,
the mask function is activated only when the HSBLC
is activated.
-- Off: Not in use.
AGC: If the images are too dark, change the maximum [AGC]
value to make the images bright.
Brightness: You can increase the brightness of the darkened
video. If you set the brightness to lower value, the image
gets darkened. If you set the brightness to higher value, the
image gets bright.
Shutter Speed: Select the desired shutter speed for camera
exposure. You can change the shutter speed to higher speed
to capture fast-moving subjects, though the image becomes
darker.
-- Max Shutter: When the [Shutter Speed] is on AUTO
mode, the [Max Shutter] function is activated. It limits
the maximum value of the [Shutter Speed].
Note:
• [Max] means when the maximum shutter speed
becomes 1/25 in case of 25 frames, and also becomes
1/30 in case of 30 frames.
• [Max Shutter] value is fixed to 1/700 on the WDR
mode.
Sens-Up: If pictures are not clear due to darkness, this SensUp operation would increase the sensitivity of picture.
Note:
If you set to one of the [Shutter Speed] options except AUTO
on the [Shutter Speed] menu or [AGC] to [OFF], the [SensUp] setting is not available.
White Balance
>> Mode: Select [Mode] option on the [White Balance] menu,
then select the following mode.
-- Auto: You can set the white balance options
automatically. When the [Mode] is set to [Auto], [Color
Temp], [Red] and [Blue] option are not activated.
-- Manual: You can set the white balance options manually.
>> Color Temp: Click to select the option.
-- Indoor: The color temperature range for the
proper white balance is approximately 3 200 K.
-- Outdoor: The color temperature range for the
proper white balance is approximately 5 100 K.
>> Red: Set the desired red value.
>> Blue: Set the desired blue value.
-- ATW (Auto-Tracing White Balance): In this mode, white
Operation and settings
--
balance has better coverage than auto. Proper white
balance may not be obtained under the following
conditions:
1. When the scene contains mostly high color
temperature objects, such as a blue sky or sunset.
2. When the scene is dim.
ONE PUSH: If you select the [ONE PUSH] mode, you will
be able to set up the White Balance automatically.
Privacy Mask
Day/Night
This function is aiming at the protection of personal privacy. The
selected part is not displayed on the screen.
>> Mode: Select [Mode] option on the [Day/Night] menu, then
select the following mode.
>> Mode: Select [ON] to set the Mask Setting menu.
>> Mask Setting: Select a type of Mask Setting.
--
Auto: [Day/Night] mode changes automatically.
Note:
--
Day: Color mode enabled.
--
Night: Black-and-white mode enabled.
The mask area can be set in different ways, depending on
the type of Mask Setting.
>> Level: Click the option to select a level.
>> Dwell Time: Click the drop-down list to select a dwell time.
•
RECTANGLE :
--
Mask Number: Click the drop-down list to select one
of the [Mask Number].
Operation and settings21
•
•
--
Mask State: Set to [On] or [Off ] on the [Mask State]
menu. When you set to [On], [Mask Color], [Width],
[Height], [Move X] and [Move Y] option is activated.
--
Mask Color : You can make any color by adjusting
R.G.B LEVEL and adjust the transparency of MASK.
--
Height: Increase or decrease the vertical size of the
mask.
--
Width: Increase or decrease the horizontal size of the
mask.
--
Move Y: Moves vertical position of the mask.
--
Move X: Moves horizontal position of the mask.
Note:
•
•
The [Privacy Mask] size is recommended to set the size default
or more.
Adjust the size about 50 % bigger, to cover the object
completely.
SmartIR
CIRCLE :
--
Mask Number: Click the drop-down list to select one
of the [Mask Number].
--
Mask State: Set to [On] or [Off ] on the [Mask State]
menu. When you set to [On], [Mask Color], [Width],
[Height], [Move X],[Move Y] and [Radius] option is
activated.
--
Mask Color : You can make any color by adjusting
R.G.B LEVEL and adjust the transparency of MASK.
--
Height: Increase or decrease the vertical size of the
mask.
--
Width: Increase or decrease the horizontal size of the
mask.
--
Move Y: Moves vertical position of the mask.
--
Move X: Moves horizontal position of the mask.
--
Radius : You can adjust the Radius size.
POLYGON :
--
22
, , , buttons to draw the polygon by moving
each vertex. Select [Move] and then , , ,
buttons to move the polygon.
Polygon Setting : Select [Draw] and then Use the
>> SmartIR: SmartIR function improve the sensitivity in the
low luminance. SmartIR analyze the image of the screen,
when the subject is close. Then SmartIR reduce the IR LED
brightness and gain to prevent saturation of the closed
subject.
--
Manual: When the [Day/Night] menu set to [Night]
mode, user can adjust the brightness of the IR LED.
Operation and settings
--
Auto: When the [Day/Night] menu set to [Night]
mode, the brightness of the IR LED will be adjusted
automatically.
--
OFF: When the [Day/Night] menu set to [Night] mode, IR
LED will be turned off.
Special
>> Area: Select the [Show] to display the area setting.
>> Width / Height: Adjust the size of the area to the left and
right or up and down.
>> Move X / Move Y: Adjust the location of the area to the left
and right or up and down.
>> Max Level: Limits the maximum brightness of IR LED. Can be
set from 0 to 200.
>> AGC Limit: When the Smart IR is working, limits the value of
maximum gain.
Note:
If the video image size is 4:3 or 5:4 mode, the D-Zoom, D-Effect,
and Stabilizer function is not activated for LNV7300 and LND7300
models.
>> Scene Mode: You can set value installed camera environment
properly using this function. Several configuration value is
set automatically to select option.
--
USER: If user change each value of function, save the
changes.
--
STD: Settings general environment .
--
BKLT: WDR set automatically to see the subject clearly
Operation and settings23
under thebacklight condition.
--
LOWLIT: Increase the Gain and set SENS-UP function to
see the subject cleary under the low light condition.
--
OUTDOOR: Change to the ELC mode not to decrease
definition under too light condition. And decrease
Brightness valuse slightly prevent to video of
supersaturation.
--
INDOOR: Condition of light set automatically to match
indoor environment.
--
TRAFFIC: Set shutter speed fast to apprehend traffic
information and status.
Note:
•
24
Set each value of option as selected option on the
[Scene Mode] like as below table.
OPTION
Max Shutter
Shutter speed
AGC
White Balance
WDR/BLC
3D-DNR
DAY/NIGHT
ACE
SHARPNESS
BRIGHTNESS
STD
1/700
AUTO
MIDDLE
ATW
Unused
MIDDLE
AUTO
Unused
34
50
BKLT
1/700
AUTO
MIDDLE
ATW
Use
MIDDLE
AUTO
Use
34
50
LOWLIT
1/700
AUTO
HIGH
ATW
Unused
MIDDLE
AUTO
Unused
34
50
OUTDOOR
1/700
AUTO
MIDDLE
ATW
Unused
MIDDLE
AUTO
Unused
34
45
SENS-UP
OFF
OFF
AUTO x10
OFF
EXPOSURE
ALC
ALC
ALC
ALC
OPTION
Max Shutter
Shutter speed
AGC
INDOOR
MAX
AUTO
MIDDLE
TRAFFIC
Manual (1/120)
HIGH
USER
-
White Balance
Manual (Indoor)
ATW
-
WDR/BLC
3D-DNR
DAY/NIGHT
ACE
SHARPNESS
BRIGHTNESS
SENS-UP
EXPOSURE
Unused
MIDDLE
AUTO
Unused
34
50
OFF
ALC
Unused
MIDDLE
AUTO
Unused
34
50
OFF
ALC
-
•
Value of [Scene Mode] is not initialized even the reboot
system. If you set to [STD], the default value of [Scene
Mode], run factory reset.
•
If you use not DC Iris lens but Manual Iris lens, must set
ELC mode on the [Exposure] option. In this case, value of
[Scene Mode] set to [USER] automatically.
•
When the [Max Shutter] value is maximum, if you set the
[Capture Mode] to 30 fps and 25 fps the shutter speed
will be 1/30 sec and 1/25 sec.
>> 3D-DNR: If pictures are not clear due to noise, this option
would reduce the noise of picture. When you use this
function, the afterimage may occur.
>> D-Effect: You can select the digital effect.
--
Mirror: Turn on the mirror effect.
--
Rotate: Rotate the picture. (180°)
--
V-Flip: Flip the picture vertically.
Operation and settings
--
Off: Turn off the digital effect.
Stream
>> D-ZOOM: Select [On] to set the digital zoom level.
--
Zoom: You can enlarge the screen.
--
Pan: You can move the screen. (left or right)
--
Tilt: You can move the screen. (up or down)
>> Color: You can switch the displayed picture to gray scale or
color.
--
--
On: To display the picture with color. If you set [On], the
[Color Level] option is activated. Adjust the [Color Level]
value using by jog controller or enter the desired value.
Off: To display the picture with grayscale.
>> Sharpness: The degree to which the boundary of the two
portions is clearly distinguished. Adjust the value using
by jog controller enter the desired value. If you set the
sharpness value to higher, the image outline becomes sharp.
If you set to lower value, the image outline becomes dim.
>> Stabilizer: The image stabilizer function minimizes the
appearance of shaky images caused by low-frequency
vibration. This function is useful for outdoor surveillance.
Select the [Stabilizer] option and set to [On] or [Off ].
>> Camera Version: Displays the software version on the
monitor.
•
•
Factory Reset: Clear certain settings and information and return
to factory default settings.
Reboot: Reboot the camera system.
Resolution
>> HD: Displays the maximum image size of the camera.
>> SD: Select the output image size of the camera.
Note:
When you use the Smart Analytics function, SD resolution is
changed as shown below.
Smart Analytics
D1
CIF
Off
704 x 480
352 x 240
On
640 x 384
320 x 192
Profile
>> Enable: Click to activate the stream function.
>> Video codec: Select the video mode (Codec) from the dropdown list. The viewer can choose among MJPEG, H.264 and
H.264_HIGH.
>> Maximum frame rate: Set the frame rate of the image.
>> GOP size: It means “Group of Pictures”. The higher the GOP,
the better is the video quality of the camera. Edit the value
of GOP from 1 to 30. This setting is valid for H.264 video
format only.
Operation and settings25
>> Quality: Select the Quality.
--
VBR: The bit rate may vary depending on the complexity
of the video to meet the selected quality.
--
CBR: The video quality may vary in order to preserve a
constant bit rate.
Region Of Interest
>> Stream quality: If the [Quality] option set to VBR, this option
is displayed. Select the stream quality from the drop down
box, the camera supports five types. (Highest, High, Medium,
Low and Lowest)
>> Alias: Enter the profile name you want to use.
>> Bit rate: If the [Quality] option set to CBR, this option is
displayed. Edit the bit rate value from 256 kbps to 10 240
kbps.
Note:
If the ‘Bit rate’ is configured too low with high resolution,
the actual frame rate will decrease because of narrow
bandwidth. So you need to set or change the ‘Bit rate’ to
high value.
•
Save: Click this button to confirm the settings.
You can set and streaming the desired area on the live view window
to use ROI(Region Of Interest) function. Select Profile4(ROI-1) to
Profile7(ROI-4).
>> Enable
1. Click to activate the [Region Of Interest] window. You can
add the 4 windows maximum for ROI function.
26
Operation and settings
2. Click the edge or corner of the window box to adjust the
window size.
Network settings
3. Click the [Save] button to save the settings.
Basic
Note:
ROI area can not overlap with each other.
Audio (Optional)
Audio In
>> Enable: Click the check box if you want to send the audio
from the microphone input connector.
Note:
The Clients connected to the IP device remain unaffected
with additional changes made in the setting.
>> Audio type: Select the type of audio encoding. (G711 PCMA,
G711 PCMU, G726 24K, G726 32K)
Audio Out
>> Enable: Click the check box to output the audio from the
speaker.
•
Save: Click this button to confirm the settings.
General
>> MAC address: Displays the MAC address.
Port & Encryption
>> Network encryption: Select the HTTP or HTTPS option for
security.
>> Smart Port Setting: Select [On] to allocate a port number
automatically.
Note:
If you select [On], [UPNP Status], [External IP], [Web Port] and
[RTSP Port] options are deactivated.
>> UPNP Status: When you use the router that is supported
UPnP function, you can set the port forwarding
automatically by using the [Smart Port Setting]. [UPnP
Status] shows connected status of router.
>> External IP: When you connect the router that is supported
UPnP function, this option is displayed. Displays the external
Operation and settings27
IP address allocated router.
the specified equipment happens on a network specifying a
single address.
>> Web port: The default HTTP port number (80) can be changed
to any port within the range 1 025 to 65 535.
>> RTP multicast: When enabled it reduces the transmission
load on the camera by making the computer of the same
segment network receive the same transmission data.
>> RTSP port: Check RTSP port. The default port is 554. Other
ports can be selected within the range 1 025 to 65 535.
Note:
The RTSP port number should not be same with the web
port number.
--
IPv4 address: Set the IP address for RTP multicast.
--
Base RTP port: Enter the port number of even number
used for the multicast streaming. Each profile uses
successive 6 port number which starts from [Base RTP
port]. It is initially set to 10 000 and you can edit this
between 10 000 and 65 530.
ARP Ping
>> Enable ARP Ping to configure IP address: Check to enable
ARP ping.
•
Note:
Save: Click this button to confirm the settings.
Each profile using multicast needs its own multicast IP
address and port numbers to avoid address conflict. When
more than 2 profiles use same multicast IP address, each
[Base RTP port] number should be distinguished from the
other port number more than 6 at least.
RTP stream
RTP (Real-time Transport Protocol) is an internet protocol that allows
programs to manage the real-time transmission of multimedia data,
via unicast or multicast.
Multicast
>> Always Multicast: Check to enable multicast regardless of
client connection.
TTL
>> TTL: This option indicates the Time-To-Live of multicast
packets. The default setting is 7, and the allowed TTL range is
from 1 to 255.
•
Save: Click this button to confirm the settings.
Profile
>> RTP unicast: When enabled the transmission of the data to
28
Operation and settings
TCP/IP
--
IPv4 address: Enter an IP address.
--
Subnet mask: Enter a subnet mask address.
--
Gateway: Enter the gateway address.
DNS server status
>> Primary DNS server: Enter the Primary domain name server
that translates the host names into IP address.
>> Secondary DNS server: Enter the Secondary DNS server
address that backups the Primary DNS.
IPv6 address status
>> Enable: Click the check box if you want to use the IPv6
address.
>> Mode
IPv4 address status
>> Automatically set with DHCP: Select this option when a
DHCP server is installed on the network to allow IP address
assignment. With this setting, the IP address is assigned
automatically.
--
Notify to SMTP server, if IP address is changed: If you
select this option, the user get a notification mail telling
about changing of IP of the IP device.
You should register the SMTP server on the Event server
setting to set this function.
•
If you select [Automatically set with DHCP], the camera
obtain IP address from DHCP server after IP address is set
“192.168.0.16”.
Manual: Select this option when you set a fixed IP
address manually.
--
Basic: Select this option to allow IPv6 address assignment
based on the Mac address. With this setting, the IP
address is assigned automatically.
--
DHCPv6: Select this option when exist a DHCPv6 server
in network. If DHCPv6 server is not existed or temporary
disability, it requests assignment every 3 minutes.
>> IPv6 address: You can enter the IP address when you select
the Manual mode. It alarms when you enter the invalid IP
address.
Note:
•
--
•
Save: Click this button to confirm the settings.
>> Statically set: Select this option when you set a fixed IP
address, with this setting, specify the IP address, Subnet
mask and default gateway manually.
Operation and settings29
DDNS
IP filtering
This free service is very useful when combined with the LG DDNS
Server. It allows the user to connect the IP device using the URL,
rather than an IP Address. This also solves the problem of having a
dynamic IP address.
The access of the IP addresses in the list are allowed or denied
according to the choice made in the drop-down list of the Basic
policy option. The administrator can add up to 10 IP address entries
to the list (a single entry can contain multiple IP addresses). The
users from these IP addresses need to be specified in the user list
with the appropriate access rights. The IP list is to control the access
permission of clients by checking the client IP address.
DDNS status
>> Don’t use DDNS server: Disable the DDNS function.
>> Use DDNS server: Enable the DDNS function.
•
--
Provider: Displays the DDNS provider.
--
Hostname: Enter the host name you want to use.
Save: Click this button to confirm the settings.
IP list
>> Basic policy: Select the basic policy type.
--
30
Allow all: Allow all the IP address basically, but the IP
addresses in the list are denied.
Operation and settings
--
Deny all: Deny all the IP address basically, but the IP
addresses in the list are allowed. It needs at least one IP
address to activate this function.
•
Remove: Click this button to delete the IPv6 address.
1. Select the alias from the list.
2. Click the [Remove] button. The IPv6 address will be deleted.
•
Save: Click this button to confirm the settings.
•
Add: Click this button to add the IP address.
SNMP
1. Click the [Add] button.
The Simple Network Management Protocol (SNMP) is an application
protocol to exchange the management information of network
devices.
2. Set the IP options.
--
Alias: Enter the alias.
--
From: Enter the start IP address for the IP filtering.
--
To: Enter the end IP address for the IP filtering.
Note:
If you want to deny or to allow a range of IP addresses, enter
the start IP address to “From” and the end IP address to “To”.
You can also add an IP address by entering the same IP
address to “From” and “To”.
3. Click the [Save] button.
4. Repeat the steps 1 to 3 to add additional IP address.
•
Remove: Click this button to delete the IP address.
1. Select the alias from the list.
2. Click the [Remove] button. The IP address will be deleted.
IPv6 address
•
Add: Click this button to add the IP address.
1. Click the [Add] button.
2. Set the IP address option.
--
Alias: Enter the alias.
--
IPv6 address: Enter the IP address for IP filtering.
3. Click the [Save] button.
4. Repeat the steps 1 to 3 to add additional IPv6 address.
SNMP v1/v2c
>> Enable SNMP v1/v2c: Selects when SNMP is allowed access
to this device.
>> Read Community: Specifies the SNMP management
community in which you want to read this system.
>> Write Community: Specifies the SNMP management
community in which you want to write this system.
SNMP v3
>> Enable SNMP v3: Selects when SNMP v3 is allowed access to
this device. It supports authentication and encryption.
>> SecurityName: Type the security name for the SNMP.
Operation and settings31
•
>> Password: Type the password for the SNMP.
802.1x
Save: Click this button to confirm the settings.
Specifies whether 802.1x network access is enabled.
QoS
You can specify network Quality of Service (QoS) settings.
802.1x/EAPOL using EAP-TLS
QoS DSCP Configuration
>> Video DSCP: Enter the priority of Video for DSCP
(Differentiated Service Code Point) Quality of Service.
>> Audio DSCP: Enter the priority of Audio for DSCP Quality of
Service.
>> Event DSCP: Enter the priority of Event for DSCP Quality of
Service.
•
Save: Click this button to confirm the settings.
>> Enable: Select on to enable the protocol. Current
authorization status of 802.1x port is displayed on buttons
right.
Certificates
>> To upload or remove the certificates
1. Click the [Browse] Button.
2. Find and open the certificates file.
--
CA Certificate: Upload the accredited certificate included
public key.
--
Client Certificate: Upload the accredited certificate
included client authentication key.
--
Client private key: Upload the accredited certificate
included client private key.
3. Click the [Upload] button to install certificates.
4. Click the [Remove] button to delete certificates.
32
Operation and settings
Basic Configuration
>> EAPOL Version: Select the EAPOL version.
>> EAP ID: Enter the ID of the client certificate using up to 16
characters.
anonymous login] option is enabled automatically.
•
You should set the SIP port number not to conflict with
multicast port and 5353.
>> Password: Enter the password of the client private key using
up to 16 characters.
•
Save: Click this button to confirm the settings.
SIP
SIP Setting
>> Enable: Set to On when you use the SIP server.
>> SIP Server: Enter the hostname or IP address of the SIP
register server.
>> UserName: Enter the name of the device used when making
calls with SIP.
>> Password: Enter the SIP server authorization password.
•
Save: Click this button to confirm the settings.
Note:
•
When you set to [On] on the [Enable] option, [Enable
Operation and settings33
User settings
the access rights to each user and then click the [Save] to
confirm your selection.
Basic
--
Administrator: Allows you to operate setup menus
and to view live images.
--
Power user: Use of the limited functions of the
system. (The Configuration menu is not allowed.)
A power user can use the Live View and audio
functions.
--
Normal user: Provides the lowest level of access,
Allows to view live images only.
--
Custom user: The user can login and view the live
stream image only when the “Enable anonymous
login” option is checked to enable it.
The IP device is shipped with the login rights of administrator only.
If others need to access the IP device excluding the configuration a
login with viewer rights need to be created. A maximum of 50 users
can be created.
Note:
Remember the password.
>> Edit the registered user
You can change the password or authority.
1. Choose the user ID and then click the [Edit] button.
2. Change the Password or Authority, then click the [Save]
button to confirm your selection.
User list
>> Add the User
You can register a new user with various access rights.
1. Click the [Add] button. User setting dialog is displayed.
2. Enter the new User ID and Password. (Should have a
minimum of 4 characters and preferably a combination
of alphanumeric.)
3. To confirm the password, retype the password that you
typed in the Password box.
4. Select the authority from the drop down list to provide
34
>> Delete the registered user
1. Choose the user ID you want to delete.
2. Click the [Remove] button.
Note:
The default administrator user ID ‘admin’ and ‘anonymous’
are permanent and cannot be deleted.
Anonymous
>> Enable anonymous login
Check the box to enable anonymous user login - allows the
Operation and settings
user access for only viewing the live stream image.
connected to the switch or hub, enabling motion
detection to each of the video streams and because of
other programs running on your computer.
Maximum RTP stream connection
>> Maximum number of simultaneous stream connection:
Set this number to limit the number of simultaneous stream
connections.
•
Save: Click this button to confirm the settings.
The connections depend on the stream configuration as
shown in the following Maximum RTP stream connection by
stream configuration.
--
--
LNU5100R, LNV5100(R), LND5100(R), LNB5100, LNB3100,
LND3100 series
Video
Codec
Resolution
Frame
Rate
Maximum RTP
stream
H.264
1 280 x 1 024
30
Up to 10
MJPEG
1 280 x 1 024
20
Up to 7
LNV7300 series, LND7300 series
Video
Codec
Resolution
Frame
Rate
Maximum RTP
stream
H.264
2 040 x 1 536
20
Up to 10
H.264
1 920 x 1 080
30
Up to 10
MJPEG
2 040 x 1 536
5
Up to 10
MJPEG
1 920 x 1 080
10
Up to 7
Note:
•
Preview window of the IP device setting and preset
setting are affected by this setting.
•
The video streaming may appear poor at times, this may
be because of the network traffic, too many devices
Operation and settings35
Event settings
the FTP server.
--
Password: Type the password for the folder shared in
the FTP Server.
--
Folder: Type the path with the folder that is shared in
the FTP server.
--
Test: Select [Test] to test the FTP server.
Event Server
Event Servers are used to receive the recorded video clip and/or
notification messages.
3. Click the [Save] button to confirm the settings.
>> To edit the FTP server
1. Choose the FTP server in the FTP server list.
2. Click the [Edit] button.
You can check or edit the FTP server options.
>> To delete the FTP server
1. Choose the FTP server in the FTP server list.
2. Click the [Remove] button. This would remove the FTP
server from the list.
FTP server list
SMTP server list
Image files can be transferred to the FTP server within the scheduled
time. Image file that has been recorded linked to an external event
is sent to the FTP server periodically.
By selecting the e-mail option, a still image of the event is captured
and an e-mail with the attached image file is sent to the specified
mail address.
>> To add the FTP server
1. Click the [Add] button. SMTP server setting window is
displayed.
2. Set the FTP server options.
2. Set the SMTP server options.
--
36
>> To add the SMTP server
1. Click the [Add] button. FTP server setting window is
displayed.
Alias: Type the FTP Server name to upload the image
files.
--
Address: Enter the FTP server’s IP address.
--
Port: Enter the port number. The default FTP port is
21.
--
User ID: Type the user name for the Folder shared in
--
Alias: Enter the SMTP server name.
--
User ID: Enter the user ID of the SMTP server. This
would be the one who owns the mail account.
--
Password: Enter the password of the SMTP server.
--
Address: Enter the SMTP server address.
Operation and settings
--
Port: Enter the port number. The default port is 25.
--
Enable SSL: Check when use the SSL (Secure Socket
Layer) protocol. SSL protocol is cryptographic
protocols that provide secure communication on a
network.
--
Receiving address: Type the recipients e-mail address.
You can specify only one recipient e-mail address.
--
Administrator address: Type the e-mail address of the
administrator.
--
Subject: Enter the subject/title of the e-mail.
--
Message: This message can describe the information
of the acquired IP address, etc.
--
Sensor & Relay (Optional)
Sensor
>> Enable: Marks up when you want to activate the sensor.
Test: Select [Test] to test the SMTP server.
>> Alias: Displays the sensor name.
3. Click the [Save] button to confirm the settings.
>> To edit the SMTP server
>> Type: Select the sensor type.
Relay
1. Choose the SMTP server in the SMTP server list.
>> Control duration: Enter the relay time.
2. Click the [Edit] button.
You can check or edit the SMTP server options.
>> Alias: Displays the relay name.
>> Type: Select the relay type.
>> To delete the SMTP server
>> Control relay
1. Choose the SMTP server in the SMTP server list.
2. Click the [Remove] button.
•
--
Run: Click to activate the relay.
--
Stop: Click to stop the relay.
Save: Click this button to confirm the settings.
Operation and settings37
Motion detect
How to set the motion detect window
1. Click the [Add] button. The motion detect window is
displayed. You can add the five windows maximum for
motion detection area.
2. Set the [Sensitivity] option.
3. Click the edge or corner of the window box to adjust the
window size for motion detection.
4. Click the [Save] button to save the settings.
Note:
Preview
•
You can reset the window size. Click one of the window edge
or corner and drag & drop to reset the motion detection
area.
•
Motion Detection can be activated when at least one of
channels(HD/SD) is enabled, Video codec is set to H.264 and
GOP size is more than 2.
You can preview the motion detection window on the preview
window.
General
>> Sensitivity: Enter the sensitivity to detect an object in
motion.
>> Save: Click this button to confirm the settings.
Note:
Motion detect function may not normal operate as installation
environment.
38
Operation and settings
Smart Analytics (Optional)
Note:
•
The [Smart Analytics] option is ancillary function and
performance is depends on installation environment or
configuration.
•
SD resolution is changed when you use the Smart Analytics
function.
Intelligent Motion Detection
Detect the motion of object where you set the zone.
Smart Analytics Monitoring
>> Enable : Set to [ON] or [OFF]. Setup menu is appeared when
selects [ON].
Event
Select the Event. (Intelligent Motion Detection, Streaming Metadata,
Trip Zone, Object Counting) If you choose option, selected option is
activated.
Preview
You can preview the camera image on the preview window.
Note:
•
Double click the preview screen to maximize full screen.
•
To return to previous screen to double click full screen.
>> Zone: Set the zone.
--
Add
1. Click the [Add] button. When you click on the
preview screen, yellow cross point is displayed.
2. Click again to make another point. The point is
connected as sky blue line from previous point.
Operation and settings39
3. To complete the zone, move the mouse cursor from
the selected points and click the mouse right button.
Note:
•
When you select all of point, you can set up to 15
points and area is set automatically.
•
You can cancel the point by click the mouse right
button near the other point.
•
If the path is intersected each other, area setting can
not complete.
•
Up to 4 Zone is available to set.
--
Delete: Delete the selected zone.
--
Delete All: Delete all of the motion area.
Streaming Metadata
Send the VA Metadata where detected zone of the user’s setting for
use from the Client. The camera do not conduct the VA detection.
>> Basic Configuration
--
Sensitivity: Select the sensitivity from drop-down list to
detect an object in motion.
--
Object Size
1. Click the check box of the [Modify] option.
2. The rectangular zone of the maximum and the
minimum object size are displayed.
3. Drag the point of the rectangular zone to adjust the
size.
Note:
•
•
When you click [Modify], value of maximum and
minimum object size is initialized.
•
Width and Height of zone are displayed as
percentage of the screen automatically.
•
Maximum value is more than minimum value.
Save: Click this button to confirm the settings.
40
>> Zone: Set the zone.
--
Set
1. Click the [Set] button. When you click on the preview
screen, yellow cross point is displayed.
2. Click again to make another point. The point is
connected as sky blue line from previous point.
Operation and settings
3. To complete the zone, move the mouse cursor from
the selected points and click the mouse right button.
Note:
--
•
When you select all of point, you can set up to 15
points and area is set automatically.
•
You can cancel the point by click the mouse right
button near the other point.
•
If the path is intersected each other, area setting can
not complete.
Trip Zone
Detect the direction of object by dividing two of zone.
Delete: Delete the zone.
>> Basic Configuration
--
Sensitivity: Select the sensitivity from drop-down list to
detect an object in motion.
--
Object Size
1. Click the check box of the [Modify] option.
2. The rectangular zone of the maximum and the
minimum object size are displayed.
3. Drag the point of the rectangular zone to adjust the
size.
Note:
•
•
When you click [Modify], value of maximum and
minimum object size is initialized.
•
Width and Height of zone are displayed as
percentage of the screen automatically.
Save: Click this button to confirm the settings.
>> Zone: Set the zone.
--
Split:
1. Click the [Set1] button. When you click on the
preview screen, yellow cross point is displayed.
Operation and settings41
Note:
2. Click again to make another point and the point is
connected as sky blue line from previous point.
3. Click the mouse right button to complete the zone.
Note:
•
You can cancel the point by click the mouse right
button near the other point.
•
If the path is intersected each other, area setting
can not complete.
•
•
When you click [Modify], value of maximum and
minimum object size is initialized.
•
Width and Height of zone are displayed as
percentage of the screen automatically.
Save: Click this button to confirm the settings.
4. Click [Set2] and select side of the previous zone.
5. Repeat the steps 1 to 3 to add other positions.
6. Click [Delete All] to clear all of the area.
--
Directionality: Select the movement direction of object.
Note:
•
When you select all of point, you can set up to 15
points and area is set automatically.
•
You can cancel the point by click the mouse right
button near the other point.
•
If the path is intersected each other, area setting can
not complete.
>> Basic Configuration
--
Sensitivity: Select the sensitivity from drop-down list to
detect an object in motion.
--
Object Size
1. Click the check box of the [Modify] option.
2. The rectangular zone of the maximum and the
minimum object size are displayed.
3. Drag the point of the rectangular zone to adjust the
size.
42
Operation and settings
Object Counting
>> Basic Configuration
Detect the direction of object by dividing two of zone. Detect zone
is divided automatically as vertically or horizontally. The number of
detection is displayed on center bottom of the preview screen.
--
Sensitivity: Select the sensitivity from drop-down list to
detect an object in motion.
--
Object Size
1. Click the check box of the [Modify] option.
2. The rectangular zone of the minimum object size is
displayed.
3. Drag the point of the rectangular zone to adjust the
size.
Note:
•
•
When you click [Modify], value of minimum object
size is initialized.
•
Width and Height of zone are displayed as
percentage of the screen automatically.
Save: Click this button to confirm the settings.
>> Zone: Set the zone.
--
Split: Select the method of dividing the zone either
vertically or horizontally.
--
Directionality: Select the movement direction of object.
Operation and settings43
Triggered Event
the FTP server. Image file and suffix setting is
available. You can select Date/Time or Sequence
of Suffix.
When an event (VA/ Motion detect/ Sensor Event) occurs, this unit
records the live images and routes as configured.
•
Stream: Selects the stream of the connected camera.
•
Programmable Alarm (Optional): When the sensor
event is activated, the camera will start the recording
with the setting value of these options. Using this
function, you can get high quality recorded image.
1. Click the check box if you want to activate this
function.
2. Sets the options.
Event schedule list
>> To edit the Event Schedule
1. Select the Trigger event and click the [Edit] button.
Event schedule window is displayed.
2. Set the options.
•
44
Trigger: Display the selected trigger event and the
current state of trigger. Current state of trigger is
Displayed to On or Off.
•
Time: Sets the weekday, Start, Finish, Pre alarm, Post
alarm and Ignore interval time options.
•
Action: Selects the options. This occurs when the
event runs.
--
FTP server/SMTP server: Uploading of images to
an FTP server, or e-mail notification.
--
Control relay(Optional): The relay is activated or
deactivated.
--
SDCard recording: Record on the SD card when
the event runs.
--
FTP server(JPEG): Sends the JPEG Image to
3. Click the [Save] button to confirm the settings.
Note:
•
You should register the SMTP and FTP server on the
Event server setting to set this function.
•
Recording of event(VA/Motion detect/Sensor event) runs
every 5 minutes split file.
•
Used stream is profile of Master or HD resolution in case
of FTP(JPEG) transmission.
Operation and settings
Scheduled Event
Note:
•
•
You can select through drag of Activation Time table that is
possible to select according to weekday and time.
•
Used stream is profile of Master or HD resolution in case of
FTP(JPEG) transmission. If always checkbox next to FTP(JPEG)
is checked, FTP(JPEG) is always enable regadless of the
activation time.
Save: Click this button to confirm the settings.
Activation Time
>> Always : You can use always by using the FTP server
regardless of activation time.
>> Only scheduled time: Continuously record according to the
set time and the selected weekday.
Action
Set the below option.
>> SDCard recording : Record to SD Card when event occurs.
Selects the camera stream for SD card recording.
>> FTP server(JPEG) : Upload the image or send the e-mail to
the FTP server. Send Image per, Base File Name and Suffix
setting are available.
Operation and settings45
Reference
Troubleshooting
This section provides useful information to help you to resolve any difficulty you might have with your LG IP device. Fault symptoms,
possible causes and remedial actions are provided here.
IP Setting problems
•
ARP/Ping: Disconnect and reconnect the power to the network camera. The device should get the IP within 2 minutes.
•
Ping your camera: Open the command prompt on your computer, type ping with the IP address of the network device. The reply
obtained by this command provides explanation for the cause of the problem.
1. bytes = 32 time = 2 ms indicates that the IP address is already used and cannot reuse the same. A new IP address needs to be
obtained.
2. Destination host unreachable: indicates that the network device and your computer do not fall in the same subnet hence needs to
get a new IP address. Contact the system administrator for the required help.
3. Request timed out: Indicates that the IP is free as it is not used by anyone and the network device can obtain this.
•
IP Conflicts: If the LG network device is set with a static IP address and if the DHCP option is set then there may be IP’s same as the
network device and other network partner. Hence set the static IP address to 0.0.0.0 to resolve this conflict.
Cannot access the camera from browser:
•
Reconnect the network camera with power and check the ping operation to know if the IP is used by others.
•
Disable the proxy setting in the Browser if you are using a proxy server.
•
Check for proper cabling and network connections, try to ping after verifying the connectivity.
•
Sometimes when HTTPS is enabled, we would be checking the URL with http, in this case manually change the URL to the http/https
accordingly.
•
Verify the DNS and Gateway settings if the IP address is assigned statically to the network device.
46
Reference
Accessing camera external to the local network
•
Firewall Protection: Check for the internet firewall with the system administrator, either he has to do port forwarding or modify the DMZ
function on the router.
•
Default router needed: Check if you need configure the router settings.
Sporadic network performance
•
Network Switches or hubs used may be of the lower configuration and the load on this may not meet the required conditions of our
network camera.
•
Check for the RJ-45 cables that are used for the network connectivity.
•
If POE is used check if the power is got by the network camera when connected to it.
Login Password lost
•
Reset the camera by pressing the Reset button for more than 3 seconds to restore default settings.
•
After the factory settings login using the default user name and password.
Video Streaming problems
•
If the video streaming does not start on the Web browser, install the LG Web Client ActiveX program on your computer following the
instructions on the Web browser.
•
When Windows IE browsers are used always take care to allow pop ups, check this option before we run the web client.
•
Check the quality of image by referring the video settings as described in the manual.
•
Sometimes there would be intermittent or very slow video streaming, this may be because of the higher resolution and frame rate that
are set for the video.
•
The video streaming may appear poor at times, this may be because of the network traffic ,too many devices connected to the switch or
hub, enabling motion detection to each of the video streams and because of other programs running on your computer.
•
If the images appear to be blurred adjust the focus of the network camera to get a clear image.
•
Video images if appear white and black adjust the settings in the OSD to get back the colorful image.
•
Select the Night mode if the network camera is connected at a place where surrounding light is less or dark.
Reference47
•
If we obtain lower frame rate than set we need to check from the system administrator for sufficient bandwidth available or reduce the
number of applications running on the client computer.
•
If the client PC’s are unable to access the multicast stream, check with the system administrator for the use of a valid multicast address or
check if the router is supporting multicasting.
•
If the images appear to have white of gray stripes on it, upgrade the Video graphics driver on the client PC to the latest version.
•
Video images may be noisy if you are using the camera in a very low light environment or the bit rate/quality is set to very low values.
Provide higher values for quality and support the surrounding environment with enough light.
Audio condition
The client computer that is interacting with the camera needs to have a sound card that is functional to support speaker and microphone.
The sound card needs to be checked for its support for full duplex communication.
Ensure that the mute button of the client computer is not set and all the audio settings are correct.
Speaker button on the web viewer should be enabled to listen the audio from the network camera.
Ensure that the bidirectional audio button is enabled on the Web viewer and the microphone is set.
Change the input and the output gain for microphone and the speaker respectively to set correct audio level.
Clear browser’s Cache
•
If your browser is not working correctly after upgrade firmware. Please follow the below solution.
•
Solution: Deleting your browser’s cache may be resolved this issue.
1. Open Internet Options in browser Tools menu and click the [Delete Files] button in the second entry (Internet temporary files).
2. Check the other settings that should not be changed.
RCA output problem
•
RCA output use to initial installation.
•
Depending on the IP Camera usage scenario, RCA output video may not be smooth. It is used for initial installation only.
48
Reference
BNC output usage
BNC connector is for convenience of camera installation, and it is not suited to surveillance.
For all further support please contact the supplier or forums or websites.
Open source software notice
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://
opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available
for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such
distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is valid for three (3)
years from the date on which you purchased the product.
Reference49
Specifications
LNB5100/LND5100/LNV5100 Series
Item
LNB5100
LND5100
Image Device
6.08 mm (1/3 type) Progressive Scan CMOS (1.3 Mega Pixels)
Lens Type
DC-Iris, CS Mountable (Optimization of
6.08 mm (1/3 type) Lens of 1.3 Mega Pixels or
above)
Day/Night
ICR
Minimum
Illumination
Color
LNV5100
2.8 mm to 10 mm F1.2
0.3 lx (F1.2, Sens-up off )
0.01 lx (F1.2, Sens-up x60)
B/W
0.005 lx (F1.2, Sens-up off )
0.0001 lx (F1.2, Sens-up x60)
WDR
Support
Image Enhancement
Backlight Compensation, 2D+3D-DNR, Exposure Control, Sens Up Control, AGC, White
Balance, Privacy Masking, EIS, Sharpness, Digital Zoom, Scene mode
Video Analytics
Motion detection, Intelligent motion detection, Trip zone, Object counting, Streaming
metadata
Resolution (Maximum)
Up to 1 280 x 1 024
Output
RJ-45 (Network), RCA (Installation)
Frame Rate (Maximum)
30 fps @ 1 280 x 1 024, 30 fps @ 720p
Compression
H.264_HIGH, H.264, MJPEG
Multi-Streaming
Dynamic Profile (Up to 7)
ROI (Region of Interest)
Support
Audio In/Out
1/1
Audio Compression
G.711, G.726
50
Reference
2-way Audio
Support
SD Slot
micro SD
EVENT
Alarm In/Out
1/1
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Integrated Client
LVi510
Remote S/W
LVi510, Mobile application (iPhone, Android, iPad)
Connections
Up to 10
Security
Password Protection, HTTPS(SSL, TLS), IEEE 802.1X
Ethernet
10/100 Ethernet
Protocol
IPv4 and IPv6
TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP
IPv4
FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
Open Protocol
ONVIF 2.2 Profile S,PSIA 1.1
Operation Temperature/Humidity
-10 ºC to 50 ºC / 0 % RH to 80 % RH
Power Source
PoE, DC12V
Power Consumption
5.9 W
Input current
Maximum 440 mA (DC 12 V), Maximum 140 mA (PoE)
Dimension
68.6 mm x 54.0 mm x 121.5 mm (W x H x D)
140 mm x 120 mm
(Ø x H)
140 mm x 122 mm
(Ø x H)
Weight
365 g
610 g
964 g
Reference51
LNB3100/LND3100 Series
Item
LNB3100
LND3100
Image Device
6.08 mm (1/3 type) Progressive Scan CMOS (1.3 Mega Pixels)
Lens Type
DC-Iris, CS Mountable (Optimization of
6.08 mm (1/3 type) Lens of 1.3 Mega Pixels
or above)
Day/Night
Digital
Minimum Illumination
0.3 lx (F1.2, Sens-up off )
0.7 lx (F1.2, Sens-up off )
0.01 lx (F1.2, Sens-up x60)
0.05 lx (F1.2, Sens-up x60)
3 mm F2.0
WDR
Support
Image Enhancement
Backlight Compensation, 2D+3D-DNR, Exposure Control, Sens Up Control, AGC, White
Balance, Privacy Masking, EIS, Sharpness, Digital Zoom
Video Analytics
Motion detection
Resolution (Maximum)
Up to 1 280 x 1 024
Output
RJ-45 (Network), RCA (Installation)
Frame Rate (Maximum)
30 fps @ 1 280 x 1 024, 30 fps @ 720p
Compression
H.264_HIGH, H.264, MJPEG
Multi-Streaming
Dynamic Profile (Up to 7)
ROI (Region of Interest)
Support
SD Slot
micro SD (Optional)
EVENT
Event Notification
Email, FTP
Pre Event Buffering
Support
Integrated Client
LVi510
Remote S/W
LVi510, Mobile application (iPhone, Android, iPad)
Connections
Up to 10
52
Reference
Security
Password Protection, HTTPS(SSL, TLS), IEEE 802.1X
Ethernet
10/100 Ethernet
Protocol
IPv4 and IPv6
TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP
IPv4
FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
Open Protocol
ONVIF 2.2 Profile S,PSIA 1.1
Operation Temperature/Humidity
-10 ºC to 50 ºC / 0 % RH to 80 % RH
Power Source
PoE, DC 12 V
Power Consumption
5.9 W
Input current
Maximum 440 mA (DC 12 V), Maximum 140 mA (PoE)
Dimension
68.6 mm x 54.0 mm x 121.5 mm (W x H x D)
140 mm x 110 mm (Ø x H)
Weight
357 g
506 g
Reference53
LNU5100R/LND5100R/LNV5100R Series
Item
LNU5100R
LND5100R
Image Device
6.08 mm (1/3 type) Progressive Scan CMOS (1.3 Mega Pixels)
Lens Type
2.8 mm to 10 mm F1.2
Day/Night
ICR
Minimum
Illumination
Color
0.3 lx (F1.2, Sens-up off )
0.01 lx (F1.2, Sens-up x60)
B/W
0 lx (LED On)
LNV5100R
IR Distance
30 m
WDR
Support
Image Enhancement
Backlight Compensation, 2D+3D-DNR, Exposure Control, Sens Up Control, AGC, White
Balance, Privacy Masking, EIS, Sharpness, Digital Zoom, Scene mode , SmartIR
Video Analytics
Motion detection, Intelligent motion detection, Trip zone, Object counting, Streaming
metadata
Resolution (Maximum)
Up to 1 280 x 1 024
Output
RJ-45 (Network), RCA (Installation)
Frame Rate (Maximum)
30 fps @ 1 280 x 1 024, 30 fps @ 720p
Compression
H.264_HIGH, H.264, MJPEG
Multi-Streaming
Dynamic Profile (Up to 7)
ROI (Region of Interest)
Support
Audio In/Out
1/1
Audio Compression
G.711, G.726
2-way Audio
Support
SD Slot
micro SD
54
20 m
Reference
EVENT
Alarm In/Out
1/1
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Integrated Client
LVi510
Remote S/W
LVi510, Mobile application (iPhone, Android, iPad)
Connections
Up to 10
Protection
IP66, IK10
Security
Password Protection, HTTPS(SSL, TLS)
Ethernet
10/100 Ethernet
Protocol
Not Support
IPv4 and IPv6
TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP
IPv4
FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
IP66, IK10
Open Protocol
ONVIF 2.2 Profile S,PSIA 1.1
Operation Temperature/Humidity
-10 ºC to 50 ºC / 0 % RH to 80 % RH
Power Source
PoE, DC 12 V, AC 24 V
PoE, DC 12 V
Power Consumption
9.9 W
7W
Input current
Maximum 590 mA (AC 24 V),
Maximum 690 mA (DC 12 V),
Maximum 190 mA (PoE)
Maximum 590 mA (DC 12 V), Maximum 170 mA (PoE)
Dimension
84 mm x 83.5 mm x 339 mm
(W x H x D)
140 x 120 mm (Ø x H)
140 x 122 mm (Ø x H)
Weight
1.4 kg
(with Sunshield 1.57 kg)
570 g
927 g
Reference55
LNV7300/LND7300 Series
Item
LNV7300
Image Device
6.49 mm (1/2.8 Type) Progressive Scan CMOS (3 Mega Pixels)
Lens Type
3 mm to 9 mm F1.2
Day/Night
ICR
Minimum
Illumination
(30 IRE)
Color
B/W
LND7300
0.4 lx (F1.2, Sens-up off )
0.012 lx (F1.2, Sens-up x60)
0.005 lx (F1.2, Sens-up off )
0.0009 lx (F1.2, Sens-up x60)
WDR
Support
Image Enhancement
Backlight Compensation, 2D+3D-DNR, Exposure Control, Sens Up Control, AGC, White
Balance, Privacy Masking, EIS, Sharpness, Digital Zoom, Scene mode
Motion detection, Intelligent motion detection, Trip zone, Object counting, Streaming
metadata
Video Analytics
Resolution (Maximum)
Up to 2 040 x 1 536
Output
RJ-45 (Network), RCA (Installation)
Frame Rate (Maximum)
20 fps @ 2 040 x 1 536, 30 fps @ 1 920 x 1 080
Compression
H.264_HIGH, H.264, MJPEG
Multi-Streaming
Dynamic Profile (Up to 7)
ROI (Region of Interest)
Support
Audio In/Out
1/1
Audio Compression
G.711, G.726
2-way Audio
Support
SD Slot
micro SD
56
Reference
EVENT
Alarm In/Out
1/1
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Integrated Client
LVi510
Remote S/W
LVi510, Mobile application (iPhone, Android, iPad)
Connections
Up to 10
Protection
IP66, IK10
Security
Password Protection, HTTPS(SSL, TLS), IEEE 802.1X
Ethernet
10/100 Ethernet
Protocol
Not Support
IPv4 and IPv6
TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP
IPv4
FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
Open Protocol
ONVIF 2.2 Profile S,PSIA 1.1
Operation Temperature/Humidity
-10 ºC to 50 ºC / 0 % RH to 80 % RH
Power Source
PoE, DC 12 V
Power Consumption
5.9 W
Input current
Maximum 590 mA (DC 12 V), Maximum 170 mA (PoE)
Dimension (Ø x H)
140 x 122 mm
140 x 120 mm
Weight
949 g
598 g
Reference57
Download PDF