LG | LNP2810 | LG LNP2810 Owner’s Manual

OWNER’S MANUAL
Network
Dome
Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODELS
LW9422 series
LNP2810 series
LNP2810T series
LNP3020T series
LNP3022 series
LNP3022T series
1411 (V2.5)
Contents
Introduction.................................................................................... 3
Operation and settings.................................................................. 4
Before using the system......................................................................4
Recommended PC Requirements....................................................4
Accessing the LG IP device.................................................................5
LG Smart Web Viewer Overview.......................................................6
Configuration menu overview...........................................7
Configuring the LG Network Camera Device...............................7
Accessing the Configuration menu..................................7
System settings........................................................................8
Audio & Video settings.......................................................11
Network settings..................................................................19
User settings..........................................................................22
Event settings........................................................................23
OSD Menu Setup.................................................................................26
General Operation...............................................................27
Focus setting.........................................................................27
Exposure settings.................................................................28
White Balance settings.......................................................28
Day/Night settings..............................................................29
Privacy setting.......................................................................29
3D-DNR setting.....................................................................29
Special menu settings........................................................30
Reset setting..........................................................................31
Reference...................................................................................... 32
Troubleshooting..................................................................................32
Open source software notice..........................................................33
Specifications.......................................................................................34
2
Introduction
The LG Network Camera is designed to use on an Ethernet network and must be assigned an IP address to make it accessible.
This manual contains instructions on how to install and manage the LG Network Camera in your networking environment. Some knowledge
of networking environments would be beneficial to the reader.
Note that design and specification of this unit may change from the manual as quality and improvement without prior notice. Should you
require any technical assistance, please contact authorized service center.
Introduction3
Operation and settings
Before using the system
Recommended PC Requirements
•
Before using the LG IP device make sure the connections are
correct and verify whether proper power supply is used.
The LG IP device can be used with most standard operating systems
and browsers.
•
Check the connections of the LG IP device for the correct
conditions.
•
Check that the LG IP device is(are) connected to the network
and that power is supplied.
•
Once the connections are made you need to install the LG client
program to the PC from which you want to access the device.
The LG Smart Web Viewer program is automatically installed
when you connect the LG IP device.
The LG Ipsolute VMS and the LG Smart Web Viewer program
are the network program of the LG Video Server and the LG IP
cameras.
•
To view streaming video in Internet Explorer, set your browser
to allow ActiveX controls. If you find this message “This website
wants to install the following add-on: ‘IPCam_Streamer.cab’ from
‘LG ELECTRONICS INC’”, Click the yellow bar and install LG Smart
Web Viewer Program on your computer. Please set your browser
zoom level to 100%.
•
The Layouts and the Live view pages may differ with different
OS (Operating Systems) and Web Browsers.
•
Care needs to be taken not to run any other applications when
the Client Program is running as it may cause memory shortage.
•
When you set on 60 fps in mobile applications, may be
degraded the frame rate depending on mobile performance.
4
Items
Operating System
CPU
Web Browser
Requirements
Windows XP Professional,
Windows VISTA, Windows 7
Intel Core2 Quad Q6700 (2.66 GHz) or
above
Microsoft Internet Explorer (32 bit) above
the version 7.0 and below the version 9.0.
DirectX
DirectX 9.0c(Windows XP),
DirectX 11(Windows Vista/7) or above
Memory
2 GB or above RAM
Graphics Card
Resolution
256 MB or above Video RAM
2048 x 1536 (with 32 bit color) or higher
Note:
For Windows 7, please download & install ‘DirectX End-User Runtime
Web Installer’.
“http://www.microsoft.com/en-us/download/details.aspx?id=35”
Operation and settings
Accessing the LG IP device
You can access the LG IP device by following the below steps.
1.
Install LG Ipsolute VMS Program
2.
Discover the LG IP device using the IP Utility
The IP Utility can automatically discover and display LG IP
devices on your network.
The IP Utility shows the MAC address, IP address, Model
name and so on.
3.
Logging in to the LG Smart Web Viewer
3.1
Run the IP Utility and find the LG IP devices.
3.2
When the LG IP devices appear in the IP Utility
window, double-click IP address or right click on the
same IP address and select “Connect to Web Page”
to start the LG Smart Web Viewer. When accessing
the LG Smart Web Viewer, the authentication dialog
appears on the screen.
3.3
Enter the user name and password. (Note that the
default administrator user name and password are
“admin”.)
Note:
The computer running the IP Utility must be on the same
network segment (physical subnet) as the LG IP device.
2.1
Run the IP Utility program.
2.2 Click the [Search] button or select the [Search]
option in the Device search menu.
After a few seconds the found LG IP devices gets
displayed in the IP Utility window.
Note:
Default password must be changed for security after
initial connection.
3.4 Click the [OK] button and then the LG Smart Web
Viewer is displayed in your browser.
Note:
•
You can also access the LG Smart Web Viewer as shown
below.
3.1 Start your Web browser.
3.2 Enter the IP address of the LG IP device in the
address bar of the browse.
3.3 Enter the user name and password set by the
administrator.
3.4 Click the [OK] button and then the LG Smart Web
Viewer is displayed in your browser.
•
The LG Smart Web Viewer needs more time to display it
according to the network conditions.
•
If the login window is not displayed, check the pop-up
blocker. If you set the pop-up blocker, the login window
is not displayed. You must allow the pop-ups.
•
If you connect the LG Smart Web Viewer for the first
time, the Security Warning window is displayed to install
the LG Smart Web Viewer program. You must install the
LG Smart Web Viewer program for using the LG IP device.
•
If your computer or network is protected by a proxy or
firewall, the proxy or firewall settings can prevent the LG
Smart Web Viewer program. Change the proxy or firewall
settings to activate the LG Smart Web Viewer program.
Operation and settings5
LG Smart Web Viewer Overview
Click to effect and then check the check
box of [Edge Enhancement] option. The
user gets more sharp reception on the
live view window.
Note:
This feature only affects the live view
window.
Click to save the current image in JPEG
format on your computer.
1. Click the [Snapshot] button and then
the Snapshot window is displayed.
2. Click the [Save] button in the
Snapshot window.
3. Enter the file name (JPEG format) and
select the folder to save it.
Note:
The language displayed on the screen may differ by models.
Item
Description
Select the video image size from the
drop-down list.
(FULL SCREEN / AUTO RESIZE /
1920x1080 / 1280x720 / D1 / CIF)
Note:
•
Select [FULL SCREEN] to enlarge full
screen of monitor. To return previous
screen, press ESC key or double click.
•
When you select [AUTO RESIZE], size
of live view screen fit to window.
Ratio imaging is fixed by width
based.
•
When you change view size option
larger on high resolution image,
browser function may not work
smoothly.
It displays Video Codec, Resolution and
FPS of the selected video stream.
Check this option as the network
connection type (TCP or UDP). If you
check it, the client connects to the server
using TCP connection.
Select buffering time of live stream.
Click to display the check box of
[Hostname], [Framerate] and [Bitrate]
options. [Display] is displayed on left
top of the live view window in order of
selecting options.
4. Click the [Save] button to confirm it.
5. Click the [Cancel] button in the
Snapshot window to close it.
Displays the Camera OSD control
window. Use these buttons to setup the
Camera. This button does not appear on
the screen if the login is other than the
administrator. (LW9422 model only)
Displays the PTZ control window. Use
these buttons to control the PTZ unit.
This button is not displayed with normal
or anonymous user.
Select the video stream. From the Live
view drop-down list, select the desired
video image source.
Profile1(HD), Profile2(SD), Profile3(JPEG),
Profile4(ROI-1), Profile5(ROI-2),
Profile6(ROI-3), Profile7(ROI-4)
Note:
You can set the stream configurations
independently. This would facilitate the
user to set the live view at his comfort.
Provides all the necessary tools
for setting up the device to your
requirements. The user will need
administrator level to do this.
Note:
If you want to exit the Configuration
menu, select one of the video stream in
the Live view drop-down list.
Displays the current surveillance live
screen. You can monitor the camera
image on the live view window of the LG
Smart Web Viewer.
Video Analysis
>> Hide: Video Analysis display
function is not in use.
>> MD: Displays the Motion
Detection function to the live
view window.
Click this button and drag the area to
use digital PTZ function. Right-clicking
the screen will bring up the previous
magnification.
(Color icon: On, Gray scale icon: Off.)
Note:
When you use the DPTZ function, all
of Display function is deactivated for
a while.
6
Operation and settings
Configuration menu overview
1. Click this button to open the folder
browse window. Click the button
again in next time, video is recorded
automatically without selection of
folder.
The following table shows the list of menu items.
The configuration images are different from each model.
Main Menu
Note:
If you want to change the folder,
move to other pages or press
therefresh button.
System
2. Recording button is activated and
recording will be started.
Note:
If recording exceed the time(1 hour)
or size limit (1 GB), recording is
stopped automatically with warning.
Audio & Video
3. To stop the recording, click this
button during the recording.
Click this button to connect or
disconnect the audio communication
between the LG IP device and the
connected PC.
Network
(Color icon: On, Gray scale icon: Off.)
Sub Menu
Version
Date & Time
Maintenance
Storage
Text Overlay
Log & Report
Language
Camera
Stream
Audio
PTZ Configuation
Preset
Auto Tracking
Basic
RTP stream
TCP/IP
DDNS
IP filtering
SNMP
Note
Option
QoS
Click this button to switch the
microphone off and on for the computer.
802.1x
(Color icon: On, Gray scale icon: Off.)
SIP
User
Click this button to switch the sound off
and on, for the speaker of the computer.
(Color icon: On, Gray scale icon: Off.)
Event
Option
Basic
Event server
Sensor & Relay
Motion detect
Triggered Event
Scheduled Event
Configuring the LG Network Camera
Device
The features and options of the LG IP camera are configured
through the Configuration menu.
Only administrator-level users have permission to access the
Configuration menu.
Accessing the Configuration menu
Click the [Configuration] button to display the LG Smart Web Viewer
configuration window.
Warning
The Configuration setup should be made by qualified service
personnel or system installers.
Operation and settings7
System settings
Maintenance
Version
Displays the current Model Name and Software version.
System reboot
Click the [Reboot] button to restart the IP device. It takes some
minutes for the IP device to start again.
Note:
Backup and restore
Click OSS(Open source software) link to check the information
about Open source software. Refer to the [OPEN SOURCE
SOFTWARE NOTICE] of [Reference]. (LNP3022T model only)
>> Backup: To take a backup all of the settings. If necessary, it
make possible to return to a backuped configuration.
1. Click the [Backup] button.
2. Click the [Save] button.
Date & Time
3. Follow the instructions on the browser to specify the
folder.
4. Click the [Save] button to save the settings.
>> Restore:
1. Click the [Browse] button.
2. Find and open the file in which the configuration setting
data is stored.
3. Click the [Restore] button and the system settings will be
restored and reboot the system.
Note:
Time zone
Set the time difference from GMT in the area where the IP device
is installed. Select the time zone in the area where the IP device is
installed from the drop down list.
Time mode
Backup and Restore can happen on IP device having the
same version of firmware. This feature is not intended for
multi-configurations or for firmware upgrades.
Firmware
>> Upgrade
>> Synchronize with NTP Server: Select if you want to
synchronize the IP device’s date and time with those of the
time server called NTP (Network Time Protocol). Specify the
NTP server’s name. Click the [Test] button for connection
test to the server.
1. Click the [Browse] button.
>> Synchronize with personal computer: Select if you want
to synchronize the IP device’s date and time with your
computer.
When you upgrade the system, it may take some minutes
to be done. Do not close the browser while the upgrade
is in progress. If you close the browser, it may cause a
malfunction. You should wait until the confirmation window
is displayed. When the upgrade is finished, the confirmation
window will be displayed.
>> Synchronize manually: Select if you want to set the IP
device’s date and time manually. Select the year, month and
date by clicking the calendar button. Set hour, minutes and
seconds in the edit boxes.
Note:
•
When system reboot after time setting, time of system
could be delayed. If you set the time correctly, set the
[Synchronize with NTP server] option.
•
Refer to NTP configuration as operation system of
the Recording Server when the Recording Server use
recording function and NTP server.
2. Find and open the firmware file.
3. Click the [Upgrade] button to update the firmware.
Note:
>> Initialize: The [Initialize] button should be used with caution.
Clicking it will return all of the IP device’s settings to the
factory default values. Except for the Network settings, PTZ
Protocol and Preset settings. (The option depends on the
model.)
Note:
Refer the “Clear browser’s cache” of Troubleshooting.
Server time
>> Server time: Displays the current date and time of the IP
device.
•
Save: Click this button to confirm the settings.
8
Operation and settings
Storage
>> Remove the micro SD card
1. Click the [Unmount] button. If the micro SD card is
unmounted from the system correctly, the [Unmount]
button will be changed to the [Mount] button.
2. Remove the micro SD card from the micro SD card slot
of the camera.
Note:
When you use the Unmount function, it may not progress
immediately. Operations such as recording of the system
and reading of data are required stop time before the
Unmount function is activated. You should try it again after
waiting a few minutes.
File Format
General
>> Overwrite: If the micro SD card has insufficient space and
this option will be activated. It will overwrite the oldest data.
>> DiskFull Notification: Sends an warning e-mail to the SMTP
server when the micro SD card has fully recorded. Select the
SMTP server from the drop-down list. You should register
the SMTP server on the Event server setting to set this
function.
>> Network Failure Recording: Select the check box to activate
the micro SD card recording function. If the system does
not work with recording server, the system will record the
data to the micro SD Card. When the system connect to the
recording server again, the recorded data of the micro SD
card will transfer to the recording server automatically.
>> Recording Server IP: Enter the recording server IP.
>> Set as NTP server IP: Click this button to use the entered
Recording Server IP as the NTP server IP.
>> File Format: You can selects the Recording File Format(AVI
or DAT). Recording, Search and Download are available
according to the setting.
Note:
•
SD Recording or FTP(Video) Sending Format are set
according to the setting. When you select to AVI, [Auto
Recording function] may not be activated in case of
network error.
•
IP Camera’s time will be appeared in players based on
DirectShow such as Windows Media Player and MPlayer.
File Management
Displays the recorded file of the micro SD card on the list. Click the
[Search] button to display the recorded file. The list will be updated
when you click the [Search] button.
>> To view the recorded file of the micro SD card
1. Select the search option.
Note:
•
The recorded file name is made automatically as the
“[Created date of the file]_[GMT Recording Time].DAT”
type.
•
If the capacity of the SD card remains less than 200 MB,
stop recording or overwrite new file after delete old one
as [Overwrite] setting. The overwritten file can not play
or may malfunction when you download.
•
Recorded file on the SD card, is recording 1 frame per
second when set video codec to MJPEG.
Device Management
>> Using the micro SD card
3. Displays the information of the[Disk ID], [Status],
[Capacity] options.
All: Search the all recorded files in the micro SD card.
--
Some: You can set the search condition by using the
date and time options.
2. Click the [Search] button and then the search result is
displayed on the list.
>> Download: You can download the recorded data of the
list to your PC. Select a recorded file on the list and click
the [Download] button. The two confirmation window
is displayed. You should download the all files that the
recorded file(*.DAT) and information file(*.INFO). You can
download as AVI file according to File format.
Note:
•
It is recommended to deactivate the [Overwrite]
function before you download the file. When [Overwrite]
function is activated, the downloading file might be
overwritten, if the micro SD card has insufficient space.
•
The downloaded file can be played by using the LG File
player.
1. Insert the micro SD card carefully to the micro SD card
slot of the camera.
2. Click the [Mount] button. If the micro SD card is mount­
ed to the system correctly, the [Mount] button will be
changed to the [Unmount] button.
--
>> Remove: Delete file from the SD card.
Note:
•
When the micro SD card is mounted, you should format
the micro SD card. After the micro SD card format is
finished, you should click the [Mount] button to use it.
•
When you use the micro SD card format function, it may
not progress immediately. In this case, you should try it
again after waiting a few minutes.
Operation and settings9
Text Overlay
Log & Report
Text Overlay
Log & Report status
>> Enable: Set to ON or OFF. Setup menu is appeared when
selects ON.
The System log provides a summary of the status of the IP device.
The unit records the data of the software activity in a file.
>> Date & Time : Select the ON to display time and date of
Client PC.
>> View Log: Click this button to display the system log
information.
>> Channel Name: Enter the channel name you want to use.
You type the Channel Name, it will be displayed whether
you select the ON or OFF.
--
>> View report: Click this button to display the report of the
system.
>> Flickering: Set to On or OFF.
>> Position: You can designate the position of text from drop
down list.
•
Save: Click this button to confirm the settings.
Note :
The text settings on [Text Overlay] is preserved, even though
initialize the camera from [Maintenance] or [Factory Reset].
You can change the text settings on [Text Overlay] directly.
Download: Click this button to see the log information
of system.
--
Download: Click this button to see the report
information of system.
Note :
The downloaded file is a UNIX type. If you open the file in Microsoft
Notepad, it will display the text as if the file contained no line breaks
at all.
Language
Language list
Select a language for the LG Smart Web Viewer configuration menu
and information display.
Note:
The language options may differ depending on models.
•
10
Save: Click this button to confirm the settings.
Operation and settings
Audio & Video settings
Camera (LNP2810, LNP2810T, LNP3020T, LNP3022, LNP3022T)
Preview
Camera (LW9422 series)
You can preview the camera image on the preview window.
1. Move the camera to the point you want by using the arrow
buttons.
2. Adjust the zoom, focus options.
3. Set the Pan, Tilt, Zoom or Focus speed options.
4. Click the [Save] button to confirm the settings.
General
Preview
You can preview the camera image on the preview window.
General
>> Contrast: Edit the contrast value from 0 to 100. Selecting 100
provides the image with the highest contrast.
>> Standard: Displays the video standard of the camera.
>> Sensor Framerate: You can select the Sensor Framerate value
between 30 and 25.
Note:
•
It is recommended to select Sensor Framerate value to
30 in 60 Hz region, 25 in 50 Hz region to reduce flicker.
•
Maximum FPS is set 25 when you select Sensor
Framerate value 25.
•
Save: Click this button to confirm the settings.
•
Default: Click this button to restore the IP device back to original
factory settings.
Note:
>> Contrast: Edit the contrast value from 0 to 100. Selecting 100
provides the image with the highest contrast.
>> Standard: Displays the video standard of the camera.
>> Sensor Framerate: You can select the Sensor Framerate value
between 30 and 25.
•
Save: Click this button to confirm the settings.
•
Default: Click this button to restore the IP device back to original
factory settings.
Sensor Framerate are not initialized.
Operation and settings11
Focus
Exposure
>> Mode: Select [Mode] option on the [Focus] menu, then
select the following mode.
--
Auto: Auto-focus is activated automatically.
--
ONE PUSH: The focus is activated manually. If the camera
is received auto-focus command, the camera is activated
auto-focus mode and the focus is set automatically
and then the focus mode is automatically changed to
manual mode.
--
--
>> IRIS: Select the desired lens IRIS value for camera exposure.
Select [IRIS] option on the [Exposure] menu, then select a value.
--
Auto: The lens IRIS is set automatically.
--
Manual: Select this option to set the lens IRIS manually.
[DC IRIS] level are set by one parameter unit.
Zoom Trig: The focus is activated manually. If you change
the zoom, the focus is activated automatically and then
the focus mode is automatically changed to manual
mode.
>> DC IRIS: If you select [Manual] on the [IRIS] option, [DC IRIS]
option is activated. Set the DC IRIS value.
Manual: Focus is activated automatically after the zoom
movement is finished.
>> WDR/BLC: Use WDR/BLC option to view the object clearly
in backlight conditions. Select [WDR/BLC] option on the
[Exposure] menu.
>> Focus Distance: Selects the minimum shooting distance
for the focus. Select [Focus Distance] option on the [Focus]
menu, then select a focus distance value.
>> AGC: If the images are too dark, change the maximum [AGC]
value to make the images bright.
--
>> Zoom Start: You can set the zoom start position of the
camera. When the zoom function is operated, the zoom
always will start at the selected zoom start position. Select
[Zoom Start] option on the [Focus] menu, then set a zoom
start position.
>> Zoom End: You can set the zoom end position of the camera.
If you set the zoom end position, the zoom is operated up to
the selected zoom end position. Select [Zoom End] option
on the [Focus] menu, then set the zoom end position.
Note:
The maximum [Zoom End] value depends on the model.
Note:
This function is not working, when the [Auto Tracking] is on.
•
Default: Click this button to restore the IP device back to original
factory settings.
•
WDR Level: Select the WDR level.
•
ACE: When the [WDR/BLC] menu set to [WDR], the
[ACE] menu appears. This function is used when you
want to display dark areas of WDR brightly.
--
BLC: Camera’s backlight compensation feature helps
alleviate issues of visibility in high contrast areas.
--
HSBLC (Applicable Model: LNP3022, LNP3022T): You can
see the object more clearly by covering the bright area
more than specified brightness.
>> ZTRK mode: Selects a zoom tracking mode. Zoom tracking
means focused zooming state. Select [ZTRK Mode] option
on the [Focus] menu, then select a zoom tracking mode. If
the FOCUS MODE is set to [Auto], the [ZTRK Mode] is set to
[Auto] and you can not change the [ZTRK Mode].
>> Lens Reset (Applicable Model: LNP3020T, LNP3022,
LNP3022T): Click the [Reset Now] button to reset the focus
immediately. If you want to reset the focus periodically, set
the desired duration and time from the drop-down list.
WDR: WDR (Wide dynamic range) feature can be
very helpful to cope with very challenging lighting
conditions. It is capable of capturing both of the dark
part and bright part and combining the differences into
a scene to generate a highly realistic image as original
scene.
--
•
Gray Scale: When the [WDR/BLC] menu set to
[HSBLC], the menu appears. Select the color to cover
the bright area.
•
User Scale: Select the brightness level.
•
Mask: Set the function which the area more than
specified brightness hides by certain color.
OFF: Not in use.
>> De-Fog (Applicable Model: LNP3020T, LNP3022, LNP3022T):
When the [WDR/BLC] menu set to [Off ], the [De-Fog] menu
appears. Set to [On] to remove the misty fog of image.
>> Brightness: You can increase the brightness of the darkened
video. If you set the brightness to lower value, the image
gets darkened. If you set the brightness to higher value, the
image gets bright.
>> Shutter Speed: Select the desired shutter speed for camera
exposure. You can change the shutter speed to higher speed
to capture fast-moving subjects, though the image becomes
12
Operation and settings
darker.
White Balance
>> Sens-Up: If pictures are not clear due to darkness, this
SENS-UP operation would increase the sensitivity of picture.
Note:
If you set to one of the [Shtter Speed] options except AUTO
on the [Shtter Speed] menu or [AGC] to [OFF], the [SENS-UP]
setting is not available.
•
Default: Click this button to restore the IP device back to original
factory settings.
>> Mode: Select [Mode] option on the [White Balance] menu,
then select the following mode.
--
Auto: You can set the white balance options
automatically. When the [Mode] is set to [Auto], [Color
Temp], [Red] and [Blue] option are not activated.
--
Manual: You can set the white balance options manually.
--
ATW (Auto-Tracing White Balance): In this mode, white
balance has better coverage than auto. Proper white
balance may not be obtained under the following
conditions:
1. When the scene contains mostly high color
temperature objects, such as a blue sky or sunset.
2. When the scene is dim.
--
ONE PUSH: If you select the [ONE PUSH] mode, you will
be able to set up the White Balance automatically.
>> Color Temp: Click to select the option.
--
Indoor: The color temperature range for the proper white
balance is approximately 3 200 K.
(LNP3022, LNP3022T: 3 800 K)
--
Outdoor: The color temperature range for the proper
white balance is approximately 5 100 K.
--
Not manual: This option is not to select the mode. It
means impossible to change [Color Temp].
>> Red: Set the desired red value.
>> Blue: Set the desired blue value.
•
Default: Click this button to restore the IP device back to original
factory settings.
Operation and settings13
Day/Night
Privacy Mask
>> Mode: Select [Mode] option on the [Day/Night] menu, then
select the following mode.
--
Auto: [Day/Night] mode changes automatically.
--
Day: Color mode enabled.
--
Night: Black-and-white mode enabled.
>> Level: Click the option to select a level.
This function is aiming at the protection of personal privacy. The
selected part is not displayed on the screen.
1. Select the [Privacy Mask] option.
>> Dwell Time: Click the drop-down list to select a dwell time.
•
2. Set to [On] or [Off ] on the [Mode] menu.
Default: Click this button to restore the IP device back to original
factory settings.
3. Click the drop-down list to select one of the [Mask
Number].
4. Set to [On] or [Off ] on the [Mask State] menu. If you
already registered the mask zone and [Mode] is set
to [On], the mask zone box appears on the live view
window and [Mask color], [Width], [Height], [Move X]
and [Move Y] menu is activated.
>> Mask Color : You can make any color by adjusting R.G.B
LEVEL and adjust the transparency of MASK.
>> Height: Increase or decrease the vertical size of the mask.
>> Width: Increase or decrease the horizontal size of the mask.
>> Move Y: Moves vertical position of the mask.
>> Move X: Moves horizontal position of the mask.
•
Default: Click this button to restore the IP device back to original
factory settings.
Note:
14
•
The [Privacy Mask] size is recommended to set the size default
or more.
•
Adjust the size about 50 % bigger, to cover the object
completely.
•
Click the [Mask Reset], before you adjust the new privacy
settings.
•
The maximum [Transparency] value depends on the model.
Operation and settings
Stream
Special
Resolution
>> HD: Displays the maximum image size of the camera.
>> SD: Select the output image size of the camera.
Profile
>> Enable: Click to activate the stream function.
>> Video codec: Select the video mode (Codec) from the dropdown list. The viewer can choose among MJPEG, H.264 and
H.264_HIGH.
>> Resolution: Displays the resolution of selected profile.
>> 3D-DNR: If pictures are not clear due to noise, this option
would reduce the noise of picture. When you use this
function, the afterimage may occur.
>> Maximum frame rate: Set the frame rate of the image.
>> GOP size: It means “Group of Pictures”. The higher the GOP,
the better is the video quality of the camera. Edit the value
of GOP from 1 to 30. This setting is valid for H.264 video
format only.
>> Color: You can switch the displayed picture to gray scale or
color.
--
--
On: To display the picture with color. If you set [On], the
[Color Level] option is activated. Adjust the [Color Level]
value using by jog controller or enter the desired value.
>> Quality: Select the Quality.
Off: To display the picture with grayscale.
>> Freeze: Click [On] or [Off ] button to set up the [Freeze]
Option.
Zoom MAG: Displays or removes the zoom OSD on the
screen. Click [On] or [Off ] button to set up the [Zoom
MAG] Option.
CBR: The video quality may vary in order to preserve a
constant bit rate.
>> Bitrate: If the [Quality] option set to CBR, this option is
displayed. Edit the bit rate value from 256 kbps to 10 240
kbps.
Note:
>> OSD: Click [On] or [Off ] button to set up the [OSD] Option.
If you set [On], [Function] and [Zoom MAG] option are
displayed.
--
--
>> Alias: Enter the profile name you want to use.
>> Stabilizer: The image stabilizer function minimizes the
appearance of shaky images caused by low-frequency
vibration. This function is useful for outdoor surveillance.
Select the [Stabilizer] option and set to [On] or [Off ].
Function: Displays or removes the Function OSD on the
screen. Click [On] or [Off ] button to set up the [Function]
Option.
VBR: The bit rate may vary depending on the complexity
of the video to meet the selected quality.
>> Stream quality: If the [Quality] option set to VBR, this
option is displayed. Select the stream quality from the drop
down box, the camera supports five types. (Highest, High,
Medium, Low and Lowest)
>> Sharpness: The degree to which the boundary of the two
portions is clearly distinguished. Adjust the value using
by jog controller enter the desired value. If you set the
sharpness value to higher, the image outline becomes sharp.
If you set to lower value, the image outline becomes dim.
--
--
•
•
If the ‘Bit rate’ is configured too low with high resolution,
the actual frame rate will decrease because of narrow
bandwidth. So you need to set or change the ‘Bit rate’ to
high value.
•
In case of LW9422 series, if you set the [Maximum Frame
rate] of master stream over than 20 fps under the 1920 x
1080 [Resolution] status, all about slave stream value is
deactivated.
Save: Click this button to confirm the settings.
>> Camera Version: Displays the software version on the
monitor.
>> Camera
-•
Factory Reset: Clear certain settings and information and
return to factory default settings.
Default: Click this button to restore the IP device back to original
factory settings.
Operation and settings15
Region Of Interest
Audio
Audio In
>> Enable: Click the check box if you want to send the audio
from the microphone input connector.
Note:
The Clients connected to the IP device remain unaffected
with additional changes made in the setting.
>> Audio type: Select the type of audio encoding.
(G711 PCMA, G711 PCMU, G726 24K, G726 32K)
Audio Out
>> Enable: Click the check box to output the audio from the
speaker.
•
Save: Click this button to confirm the settings.
You can set and streaming the desired area on the live view window
to use ROI(Region Of Interest) function. Select Profile4(ROI-1) to
Profile7(ROI-4).
>> Enable
1. Click to activate the [Region Of Interest] window. You
can add the 4 windows maximum for ROI function.
2. Click the edge or corner of the window box to adjust the
window size.
3. Click the [Save] button to save the settings.
Note:
ROI area can not overlap with each other.
16
Operation and settings
PTZ Configuation
Allows the user to configure different PTZ controls by using different
PTZ protocols.
3. Set the Pan, Tilt, Zoom or Focus speed options.
4. Click the [Save] button to confirm the settings.
Preset
Preset position is the function to register camera monitoring positions
(preset positions) associated with position numbers. By entering the
position numbers, you can move cameras to the preset positions.
>> To register preset position
1. Enter the preset number you wish to register.
2. Move the camera to a point you wish.
3. Click the [Add] button.
4. Repeat the steps 1 to 3 to add other positions.
PTZ configuration
>> To remove the preset position
>> Enable: Check to use the PTZ protocol.
1. Enter the memorized preset index number.
>> Pan speed: Enter the panning speed of the PTZ device in the
edit box. Default value is depending on protocol.
2. Click the [Remove] button. The preset will be deleted.
>> Changing a picture in a preset position
>> Tilt speed: Enter the tilting speed of the PTZ device in the
edit box. Default value is depending on protocol.
>> Zoom speed: Enter the zoom speed of the PTZ device to
view the object wide or tele at a distance. Default value is
depending on protocol.
>> Focus speed: Enter the focus speed of the PTZ device
to focus an object clearly near or far. Default value is
depending on protocol.
>> Enable Tilt Limit: Check to use the Tilt limit.
>> Auto Return Mode: This function can be used to specify
automatic return to a particular mode.
--
Off: Not in use.
--
Last Tour: After the Auto Return Time is over, the camera
restarts the previous tour.
--
Home: When the touring is stopped, returns to the
camera’s basic position after the set time.
2. Click the [Go to preset] button. The camera moves to
the preset position and the picture of the camera in that
position appears on the monitor.
Note:
•
If you check the [Set Home Preset], the preset is set to home
preset when you add the preset position.
•
If you set the home preset, the camera (LNP3022T only) returns
home preset position when the power is restarted. Otherwise, it
returns factory default position.
Preset tour
A preset tour is composed of a group of preset positions that the
operator can link together in a sequence.
1. Click the [Play] button to start the preset tour.
2. Click the [Stop] button to stop the preset tour.
Note:
Note:
You have to set the basic position to perform this
function.
Preset group tour
>> Auto Return Time: Enter the auto return time of the PTZ
device in the edit box. If you set the value to 0, auto return
feature is deactivated.
•
1. Enter the memorized preset index number.
Save: Click this button to confirm the settings.
Preset
If you control the PTZ, the preset tour will be stopped.
You can create a group using preset positions that are registered
already.
>> To set the group
1. Enter the group number in the [Group index] option.
2. Enter the preset index number in the [Preset index]
option.
3. Click the [Add] button.
4. Repeat the steps 2 to 3 to add other preset index
number. You can set the preset index number up to 8 for
the one group.
5. Repeat the steps 1 to 4 to set the other group index.
>> To remove the preset index from the group
1. Enter the group number in the [Group index] option.
2. Enter the preset index number in the [Preset index]
option.
3. Click the [Remove] button.
4. Repeat the steps 2 to 3 to remove other preset index
number.
5. Repeat the steps 1 to 4 to set the other group index.
>> To tour the group
1. Enter the group number in the [Group index] option.
2. Click the [Play] button to start the group tour.
Preview
You can see the settings screen from the preview window.
1. Move the camera to the point you want by using the arrow
buttons.
2. Adjust the zoom, focus options.
3. Click the [Stop] button to stop the group tour.
>> To delete a group
1. Enter the group number in the [Group index] option.
2. Click the [Group Remove] button. The group will be deleted.
Operation and settings17
Auto pan
>> Target Size
You can play the camera with auto pan function.
>> To set the Auto Pan position
1. Enter the index number you wish to register.
2. Move the camera to the desired point.
3. Click the [Add] button.
4. Repeat the steps 1 to 3 to add other index number. You
can set the Auto pan index number up to 8.
--
Small: Make images about 1/4 of the object using Zoom
feature.
--
Medium: Make images about 1/2 of the object using
Zoom feature.
--
Large: Make images about 3/4 of the object using Zoom
feature.
>> Camera Height: Set to the height of the camera.
1. Click the [Play] button to start the Auto Pan function.
>> TrackTime: Set the maximum time object tracking.
The camera moved to the initial position after tracking the
amount of time set.
2. Click the [Stop] button to stop the Auto Pan function.
>> Sensitivity: Set the sensitivity of detection of objects.
>> To play the auto pan
Note:
Note:
If you click the [CLEAR] button, all of Auto pan position will be
deleted.
Low sensitivity setting value can be difficult to detect of small
objects or movement.
Pattern
Lost configuration
You can activate the camera in a repeating pattern. The pattern
is programmed by recording your manual pan, tilt, and zoom
operations. The camera stores the movements you performed in
memory.
>> Action
>> To record the pattern
1. Click the [Start recording] button to start the pattern
recording.
Stay: When tracking is failed, the camera stays current
position preparing re-tracking, does not return to the
initial position.
--
Return: When tracking is failed, the camera returns to the
initial position preparing re-tracking.
>> Timeout: When tracking is failed for the first time, It tries to
re-check the object during set timeout. After that, set action
is performed.
2. Move the camera through the desired movement.
3. Click the [Stop recording] button to stop the pattern
recording.
--
•
Save: Click this button to confirm the settings.
Note:
•
The available total time of pattern differs depending on connected
PTZ device and operation.
Default: Click this button to restore the IP device back to original
factory settings.
Note:
Auto tracking (LNP2810T, LNP3020T, LNP3022T)
In case of the LNP3022T series, the initial position depends on your
home position setting. If you set the home position, the camera
returns home position when the tracking is failed. Otherwise, the
camera returns the place to start tracking.
Auto tracking
>> Enable
--
ON: Auto tracking setup menu appears. Then you can set
the values.
-- OFF: Auto tracking setup menu disappears.
Preview
You can see the settings screen from the preview window.
1. Set the camera angle to the point you want with arrow buttons.
2. Adjust the zoom, focus options.
3. Set the Pan, Tilt, Zoom or Focus speed options.
4. Click the [Save] button to confirm the settings.
Main configuration
>> Track Mode: During perform the Auto Tracking, track the
object using PT(Pan / Tilt) or PTZ(Pan / Tilt / Zoom).
18
Operation and settings
Network settings
RTP stream
Basic
RTP (Real-time Transport Protocol) is an internet protocol that allows
programs to manage the real-time transmission of multimedia data,
via unicast or multicast.
General
>> MAC address: Displays the MAC address.
Profile
>> RTP unicast: When enabled the transmission of the data to
the specified equipment happens on a network specifying a
single address.
Port & Encryption
>> Network encryption: Select the HTTP or HTTPS option for
security.
>> RTP multicast: When enabled it reduces the transmission
load on the camera by making the computer of the same
segment network receive the same transmission data. When
multicast option is checked then select Video Port number,
Audio Port number and Data port number.
>> Smart Port Setting: Select [On] to allocate a port number
automatically.
Note:
If you select [On], [UPNP Status], [External IP], [Web Port] and
[RTSP Port] options are deactivated.
>> UPNP Status: When you use the router that is supported
UPnP function, you can set the port forwarding
automatically by using the [Smart Port Setting]. [UPnP
Status] shows connected status of router.
>> External IP: When you connect the router that is supported
UPnP function, this option is displayed. Displays the external
IP address allocated router.
>> Web port: The default HTTP port number (80) can be changed
to any port within the range 1 025 to 65 535.
>> RTSP port: Check RTSP port. The default port is 554. Other
ports can be selected within the range 1 025 to 65 535.
Base RTP port: Enter the port number of even number
used for the multicast streaming. Each profile uses
successive 6 port number which starts from [Base RTP
port]. It is initially set to 10 000 and you can edit this
between 10 000 and 65 530.
Multicast
>> Always Multicast: Check to enable multicast regardless of
client connection.
TTL
>> TTL: This option indicates the Time-To-Live of multicast
packets. The default setting is 7, and the allowed TTL range
is from 1 to 255.
>> Enable ARP Ping to configure IP address: Check to enable
ARP ping.
Save: Click this button to confirm the settings.
--
Each profile using multicast needs its own multicast IP address and
port numbers to avoid address conflict. When more than 2 profiles
use same multicast IP address, each [Base RTP port] number should
be distinguished from the other port number more than 6 at least.
ARP Ping
•
IPv4 address: Set the IP address for RTP multicast.
Note:
Note:
The RTSP port number should not be same with the web
port number.
--
•
Save: Click this button to confirm the settings.
Operation and settings19
TCP/IP
DDNS
This free service is very useful when combined with the LG DDNS
Server. It allows the user to connect the IP device using the URL,
rather than an IP Address. This also solves the problem of having a
dynamic IP address.
IPv4 address status
>> Automatically set with DHCP: Select this option when a
DHCP server is installed on the network to allow IP address
assignment. With this setting, the IP address is assigned
automatically.
--
Notify to SMTP server, if IP address is changed: If you
select this option, the user get a notification mail telling
about changing of IP of the IP device.
Note:
•
You should register the SMTP server on the Event server
setting to set this function.
•
If you select [Automatically set with DHCP], the camera
obtain IP address from DHCP server after IP address is
set “192.168.0.16”.
>> Statically set: Select this option when you set a fixed IP
address, with this setting, specify the IP address, Subnet
mask and default gateway manually.
--
IPv4 address: Enter an IP address.
--
Subnet mask: Enter a subnet mask address.
--
Gateway: Enter the gateway address.
DDNS status
>> Don’t use DDNS server: Disable the DDNS function.
>> Use DDNS server: Enable the DDNS function.
•
--
Provider: Displays the DDNS provider.
--
Hostname: Enter the hostname you want to use.
Save: Click this button to confirm the settings.
IP filtering
The access of the IP addresses in the list are allowed or denied
according to the choice made in the drop-down list of the Basic
policy option. The administrator can add up to 10 IP address entries
to the list (a single entry can contain multiple IP addresses). The
users from these IP addresses need to be specified in the user list
with the appropriate access rights. The IP list is to control the access
permission of clients by checking the client IP address.
DNS server status
>> Primary DNS server: Enter the Primary domain name server
that translates the hostnames into IP address.
>> Secondary DNS server: Enter the Secondary DNS server
address that backups the Primary DNS.
IPv6 address status
>> Enable: Click the check box if you want to use the IPv6
address.
>> Mode
--
Manual: Select this option when you set a fixed IP
address manually.
--
Basic: Select this option to allow IPv6 address
assignment based on the Mac address. With this setting,
the IP address is assigned automatically.
--
DHCPv6: Select this option when exist a DHCPv6 server
in network. If DHCPv6 server is not existed or temporary
disability, it requests assignment every 3 minutes.
IP list
>> Basic policy: Select the basic policy type.
>> IPv6 address: You can enter the IP address when you select
the Manual mode. It alarms when you enter the invalid IP
address.
•
--
Allow all: Allow all the IP address basically, but the IP
addresses in the list are denied.
--
Deny all: Deny all the IP address basically, but the IP
addresses in the list are allowed. It needs at least one IP
address to activate this function.
Save: Click this button to confirm the settings.
•
Save: Click this button to confirm the settings.
•
Add: Click this button to add the IP address.
1. Click the [Add] button.
2. Set the IP options.
20
--
Alias: Enter the alias.
--
From: Enter the start IP address for the IP filtering.
--
To: Enter the end IP address for the IP filtering.
Operation and settings
Note:
QoS
If you want to deny or to allow a range of IP addresses, enter
the start IP address to “From” and the end IP address to “To”.
You can also add an IP address by entering the same IP
address to “From” and “To”.
You can specify network Quality of Service (QoS) settings.
3. Click the [Save] button.
4. Repeat the steps 1 to 3 to add additional IP address.
•
Remove: Click this button to delete the IP address.
1. Select the alias from the list.
2. Click the [Remove] button. The IP address will be deleted.
IPv6 address
•
Add: Click this button to add the IP address.
1. Click the [Add] button.
QoS DSCP Configuration
>> Video DSCP: Enter the priority of Video for DSCP
(Differentiated Service Code Point) Quality of Service.
2. Set the IP address option.
--
Alias: Enter the alias.
--
IPv6 address: Enter the IP address for IP filtering.
>> Audio DSCP: Enter the priority of Audio for DSCP Quality of
Service.
3. Click the [Save] button.
>> Event DSCP: Enter the priority of Event for DSCP Quality of
Service.
4. Repeat the steps 1 to 3 to add additional IPv6 address.
•
Remove: Click this button to delete the IPv6 address.
1. Select the alias from the list.
2. Click the [Remove] button. The IPv6 address will be deleted.
SNMP
•
Save: Click this button to confirm the settings.
802.1x
Specifies whether 802.1x network access is enabled.
The Simple Network Management Protocol (SNMP) is an application
protocol to exchange the management information of network
devices.
802.1x/EAPOL using EAP-TLS
>> Enable: Select on to enable the protocol. Current
authorization status of 802.1x port is displayed on buttons
right.
SNMP v1/v2c
>> Enable SNMP v1/v2c: Selects when SNMP is allowed access
to this device.
Certificates
>> To upload or remove the certificates
>> Read Community: Specifies the SNMP management
community in which you want to read this system.
1. Click the [Browse] Button.
>> Write Community: Specifies the SNMP management
community in which you want to write this system.
--
CA Certificate: Upload the accredited certificate included
public key.
--
Client Certificate: Upload the accredited certificate
included client authentication key.
--
Client private key: Upload the accredited certificate
included client private key.
2. Find and open the certificates file.
SNMP v3
>> Enable SNMP v3: Selects when SNMP v3 is allowed access to
this device. It supports authentication and encryption.
>> SecurityName: Type the security name for the SNMP.
>> Password: Type the password for the SNMP.
•
3. Click the [Upload] button to install certificates.
Save: Click this button to confirm the settings.
4. Click the [Remove] button to delete certificates.
Basic Configuration
>> EAPOL Version: Select the EAPOL version.
>> EAP ID: Enter the ID of the client certificate using up to 16
characters.
>> Password: Enter the password of the client private key using
up to 16 characters.
•
Save: Click this button to confirm the settings.
Operation and settings21
SIP (LNP2810, LNP2810T, LNP3020T)
User settings
Basic
The IP device is shipped with the login rights of administrator only.
If others need to access the IP device excluding the configuration a
login with viewer rights need to be created. A maximum of 50 users
can be created.
SIP Setting
>> Enable: Set to On when you use the SIP server.
>> SIP Server: Enter the hostname or IP address of the SIP
register server.
>> UserName: Enter the name of the device used when making
calls with SIP.
>> Password: Enter the SIP server authorization password.
•
Save: Click this button to confirm the settings.
Note:
•
When you set to [On] on the [Enable] option, [Enable
anonymous login] option is enabled automatically.
•
You should set the SIP port number not to conflict with
multicast port and 5353.
User list
>> Add the User
You can register a new user with various access rights.
1. Click the [Add] button. User setting dialog is displayed.
2. Enter the new User ID and Password. (Should have a
minimum of 4 characters and preferably a combination
of alphanumeric.)
3. To confirm the password, retype the password that you
typed in the Password box.
4. Select the authority from the drop down list to provide
the access rights to each user and then click the [Save]
to confirm your selection.
--
Administrator: Allows you to operate setup menus
and to view live images.
--
Power user: Use of the limited functions of the
system. (The Configuration menu is not allowed.)
A power user can use the Live View, OSD control and
audio functions.
--
Normal user: Provides the lowest level of access,
Allows to view live images only.
--
Custom user: The user can login and view the live
stream image only when the “Enable anonymous
login” option is checked to enable it.
Note:
Remember the password.
>> Edit the registered user
You can change the password or authority.
1. Choose the user ID and then click the [Edit] button.
2. Change the Password or Authority, then click the [Save]
button to confirm your selection.
>> Delete the registered user
1. Choose the user ID you want to delete.
2. Click the [Remove] button.
Note:
The default administrator user ID ‘admin’ and ‘anonymous’
are permanent and cannot be deleted.
22
Operation and settings
Event settings
Anonymous
>> Enable anonymous login
Check the box to enable anonymous user login - allows the
user access for only viewing the live stream image.
Maximum RTP stream connection
Event Server
Event Servers are used to receive the recorded video clip and/or
notification messages.
>> Maximum number of simultaneous stream connection:
Set this number to limit the number of simultaneous stream
connections.
The connections depend on the stream configuration as
shown in the following Maximum RTP stream connection by
stream configuration.
--
LW9422, LNP3020T, LNP3022(T)
Video Codec
Resolution
Frame
Rate
Quality
Maximum
RTP
stream
H.264
1920 x 1080
30
HIGHEST
Up to 10
MJPEG
1920 x 1080
10
HIGHEST
Up to 7
--
LNP2810(T)
Video Codec Resolution
Frame
Rate
Quality
Maximum
RTP
stream
H.264
1280 x 720
30
HIGHEST
Up to 10
MJPEG
1280 x 720
20
HIGHEST
Up to 7
Note:
Preview window of the IP device setting and preset setting
are affected by this setting.
•
Save: Click this button to confirm the settings.
FTP server list
Image files can be transferred to the FTP server within the
scheduled time. Image file that has been recorded linked to an
external event is sent to the FTP server periodically.
>> To add the FTP server
1. Click the [Add] button. FTP server setting window is
displayed.
2. Set the FTP server options.
--
Alias: Type the FTP Server name to upload the image
files.
--
Address: Enter the FTP server’s IP address.
--
Port: Enter the port number. The default FTP port is
21.
--
User ID: Type the user name for the Folder shared in
the FTP server.
--
Password: Type the password for the folder shared in
the FTP Server.
--
Folder: Type the path with the folder that is shared in
the FTP server.
--
Test: Select [Test] to test the FTP server.
3. Click the [Save] button to confirm the settings.
>> To edit the FTP server
1. Choose the FTP server in the FTP server list.
2. Click the [Edit] button.
You can check or edit the FTP server options.
>> To delete the FTP server
1. Choose the FTP server in the FTP server list.
2. Click the [Remove] button. This would remove the FTP
server from the list.
SMTP server list
By selecting the e-mail option, a still image of the event is captured
and an e-mail with the attached image file is sent to the specified
mail address.
>> To add the SMTP server
1. Click the [Add] button. SMTP server setting window is
displayed.
2. Set the SMTP server options.
--
Alias: Enter the SMTP server name.
--
User ID: Enter the user ID of the SMTP server. This
would be the one who owns the mail account.
--
Password: Enter the password of the SMTP server.
--
Address: Enter the SMTP server address.
--
Port: Enter the port number. The default port is 25.
--
Enable SSL: Check when use the SSL (Secure Socket
Layer) protocol. SSL protocol is cryptographic
protocols that provide secure communication on a
Operation and settings23
network.
--
Receiving address: Type the recipients e-mail
address. You can specify only one recipient e-mail
address.
--
Administrator address: Type the e-mail address of
the administrator.
--
Subject: Enter the subject/title of the e-mail.
--
Message: This message can describe the information
of the acquired IP address, etc.
--
Test: Select [Test] to test the SMTP server.
Motion detect
3. Click the [Save] button to confirm the settings.
>> To edit the SMTP server
1. Choose the SMTP server in the SMTP server list.
2. Click the [Edit] button.
You can check or edit the SMTP server options.
>> To delete the SMTP server
1. Choose the SMTP server in the SMTP server list.
2. Click the [Remove] button.
Sensor & Relay
Preview
You can preview the motion detection window on the preview
window.
General
>> Sensitivity: Enter the sensitivity to detect an object in
motion.
•
Save: Click this button to confirm the settings.
Note:
The Motion Detection function may not work depending on your
installation environment.
How to set the motion detect window
1. Click the [Add] button. The motion detect window is
displayed. You can add the five windows maximum for
motion detection area.
2. Set the [Sensitivity] option.
Sensor
>> Enable: Marks up when you want to activate the sensor.
>> Alias: Displays the sensor name.
>> Type: Select the sensor type.
Relay
3. Click the edge or corner of the window box to adjust the
window size for motion detection.
4. Click the [Save] button to save the settings.
Note:
•
You can reset the window size. Click one of the window
edge or corner and drag & drop to reset the motion
detection area.
•
Motion Detection can be activated when at least one of
channels(HD/SD) is enabled, Video codec is set to H.264 and
GOP size is more than 2.
>> Control duration: Enter the relay time.
>> Alias: Displays the relay name.
>> Type: Select the relay type.
>> Control relay
•
--
Run: Click to activate the relay.
--
Stop: Click to stop the relay.
Save: Click this button to confirm the settings.
Note:
The number of Sensor and Relay are depending on the model.
24
Operation and settings
Triggered Event
Scheduled Event
When an event (VA/ Motion detect/ Sensor Event) occurs, this unit
records the live images and routes as configured.
Activation Time
>> Always : You can use always by using the FTP server
regardless of activation time.
Event schedule list
>> To edit the Event Schedule
1. Select the Trigger event and click the [Edit] button. Event
schedule window is displayed.
2. Set the options.
•
Trigger: Display the selected trigger event and the
current state of trigger. Current state of trigger is
Displayed to On or Off.
•
Time: Sets the weekday, Start, Finish, Pre alarm, Post
alarm and Ignore interval time options.
•
Action: Selects the options. This occurs when the
event runs.
--
FTP server(VIDEO)/SMTP server: Uploading of
images to an FTP server, or e-mail notification.
--
Control relay(Optional): The relay is activated or
deactivated.
--
SDCard recording: Record on the SD card when
the event runs.
--
Move camera to: Go to the saved preset position
when event runs.
--
FTP server(JPEG): Sends the JPEG Image to
the FTP server. Image file and suffix setting is
available. You can select Date/Time or Sequence
of Suffix.
•
Stream: Selects the stream of the connected camera.
•
Programmable Alarm(Optional): When the sensor
event is activated, the camera will start the recording
with the setting value of these options. Using this
function, you can get high quality recorded image.
>> Only scheduled time: Continuously record according to the
set time and the selected weekday.
Action
Set the below option.
>> SDCard recording : Record to SD Card when event occurs.
Selects the camera stream for SD card recording.
>> FTP server(JPEG) : Upload the image or send the e-mail to
the FTP server. Send Image per, Base File Name and Suffix
setting are available.
Note:
•
•
You can select through drag of Activation Time table
that is possible to select according to weekday and time.
•
Used stream is profile of Master or HD resolution in
case of FTP(JPEG) transmission. If always checkbox next
to FTP(JPEG) is checked, FTP(JPEG) is always enable
regadless of the activation time.
Save: Click this button to confirm the settings.
1. Click the check box if you want to activate this
function.
2. Sets the options.
3. Click the [Save] button to confirm the settings.
Note:
•
You should register the SMTP and FTP server on the
Event server setting to set this function.
•
Recording of event(VA/Motion detect/Sensor event) runs
every 5 minutes split file.
•
Used stream is profile of Master or HD resolution in case
of FTP(JPEG) transmission.
Operation and settings25
OSD Menu Setup
SPECIAL
The following table shows the list of menu items and options.
This feature applies in LW9422 series only.
COLOR
Note:
FOCUS
EXPOSURE
WHITE
BALANCE
Sub Menu
Contents
FOCUS DIST
50 CM, 1 M, 3 M, 5 M
ZOOM
START
x1 to x11
OSD
ZOOM END
x2 to x144
ZTRK MODE
AUTO / MANUAL / AUTO ONLY
INITIAL SET
-
EXIT
LANGUAGE
ON/OFF
OFF
USER TITLE
ON/OFF
ZOOM MAG
ON/OFF
FUNCTION
ON/OFF
ENG/CHN(SC)/KOR/RUS/JPN/CHN(TC)
RET/TOP/END
FACTORY
RESET
-
RET/TOP/END
S/W
VERSION
-
IRIS
AUTO / MANUAL
EXIT
RET/TOP/END
AGC
OFF / LOW / MIDDLE / HIGH
WDR/BLC
OFF / WDR / BLC
BRIGHTNESS
0 to 100
SHUTTER
OFF, A.FLK, 1/160, …, 1/10 000, X2, …, X64,
AUTO
SENS-UP
AUTO X2/AUTO X3/…/AUTO X64/OFF
INITIAL SET
-
EXIT
RET/TOP/END
ATW
-
AUTO
COLOR
TEMP
INDOOR/OUTDOOR
RED
-100 to 100
BLUE
-100 to 100
ONE PUSH
-
INITIAL SET
-
AUTO
D/N LEVEL
LOW / MIDDLE / HIGH
DWELL TIME
5, 10, 15, 30 ,60 SEC
-
DAY
-
NIGHT
-
OFF
-
ON
RESET
-50 to 50
0 to 68
EXIT
MASK
NUMBER
1 to 8
MASK STATE
ON/OFF
RED
0 to 255
GREEN
0 to 255
BLUE
0 to 255
TRANSPARENCY
0 to 16
WIDTH
2 to 320
HEIGHT
2 to 240
GRID
ON/OFF
RESET MASK
-
INITIAL SET
EXIT
26
COLOR LEVEL
INITIAL SET
MASK
COLOR
3D-DNR
ON
ON
AUTO / MANUAL / ONE PUSH / ZOOM TRIG
INITIAL SET
PRIVACY
MASK
-
STABILIZER
SPECIAL
FOCUS
MODE
MANUAL
DAY/ NIGHT
ON/OFF
OFF
SHARPNESS
The top side of screen may be hidden by tilting range.
Main
Menu
FREEZE
RET/TOP/END
OFF / LOW / MIDDLE / HIGH
Operation and settings
General Operation
Focus setting
1. Click the [OSD control] button on the LG Smart Web Viewer.
2.Click button on the OSD control window.
The camera setting menu appears on the live view window.
The camera adjusts the focus automatically by sensing the center of
the picture.
FOCUS MODE
3.Use or button to select an option then click
Submenu appears.
4.Use
or
button to select a submenu option.
5.Use
or
button to select a value.
button.
6. Select [EXIT] option then click button to exit the setup menu.
In the submenu, use or button to select the [EXIT] then
use or button to select a mode and click button to exit
the setup menu.
--
RET: Return to the previous.
--
TOP: Return to the CAMERA SETTING menu screen.
--
END: Exit the setup menu.
Note:
•
button: Used to move upper direction on the menu screen.
•
button: Used to move lower direction on the menu screen.
•
button: Used to increase the value selected in the menu.
•
button: Used to decrease the value selected in the menu.
•
button: Executes selections and displays a submenu for an
item with the mark.
Select [FOCUS MODE] option on the [FOCUS] menu, then select the
following mode.
•
AUTO: Auto-focus is activated automatically.
•
MANUAL: Focus is activated automatically after the zoom
movement is finished. If you want to control the focus manually,
press the FOCUS ( or ) buttons on the controller.
•
ONE PUSH: The focus is activated manually. If the camera is
received auto-focus command, the camera is activated autofocus mode and the focus is set automatically and then the
focus mode is automatically changed to manual mode.
•
ZOOM TRIG: The focus is activated manually. If you change the
zoom, the focus is activated automatically and then the focus
mode is automatically changed to manual mode.
FOCUS DIST
Selects the minimum shooting distance for the focus. Select [FOCUS
DIST] option on the [FOCUS] menu, then select a focus distance
value.
ZOOM START
You can set the zoom start position of the camera. When the zoom
function is operated, the zoom always will start at the selected start
position.
Select [ZOOM START] option on the [FOCUS] menu, then set a zoom
start position.
ZOOM END
You can set the zoom end position of the camera. If you set the
zoom end position, the zoom is operated up to the selected zoom
end position.
Select [ZOOM END] option on the [FOCUS] menu, then set the zoom
end position
ZTRK MODE
Selects a zoom tracking mode. Zoom tracking means focused
zooming state. Select [ZTRK MODE] option on the [FOCUS] menu,
then select a zoom tracking mode (AUTO or MANUAL).
If the FOCUS MODE is set to [AUTO], the ZTRK MODE is set to [AUTO
ONLY] and you can not change the ZTRK MODE.
Operation and settings27
Exposure settings
Note:
If you set to one of the SHUTTER options except AUTO on the
[SHUTTER] menu or [AGC] to [OFF], the [SENS-UP] setting is not
available and [---] mark is displayed.
White Balance settings
Select the method by which the camera shifts its output colors to
compensate for the color of a light source.
IRIS
Select the desired lens IRIS value for camera exposure.
Select [IRIS] option on the [EXPOSURE] menu, then select a value.
•
AUTO: The lens IRIS is set automatically.
•
MANUAL: Use or button to select the DC IRIS level. DC IRIS
level are set by one parameter unit.
AGC (Automatic Gain Control)
If the images are too dark, change the maximum [AGC] value to
make the images bright.
or
2.Use
•
1. Select the [AGC] option on the [EXPOSURE] menu.
2. Use
1. Select the [WHITE BALANCE] option.
button to select a mode.
WDR/BLC
or
button to select a mode then click
button.
ATW (Auto-Tracing White Balance): In this mode, white
balance has better coverage than auto. Proper white balance
may not be obtained under the following conditions:
>> When the scene contains mostly high color temperature
objects, such as a blue sky or sunset.
Use WDR/BLC option to view the object clearly in backlight
conditions.
>> When the scene is dim.
1. Select [WDR/BLC] option on the [EXPOSURE] menu.
•
AUTO: You can set the white balance options automatically.
2.Use
•
ONE PUSH: If you select the ONE PUSH mode, you will be
able to set up the White Balance automatically using
button.
•
MANUAL: You can set the white balance options manually.
•
or
button to select a mode then click
button.
WDR: WDR (Wide dynamic range) feature can be very helpful
to cope with very challenging lighting conditions.
It is capable of capturing both of the dark part and bright
part and combining the differences into a scene to generate
a highly realistic image as original scene. Set the WDR limit.
>> ACE (Adaptive Contrast Enhancement) : This function
is used when you want to display dark areas of WDR
brightly.
•
BLC: Camera’s backlight compensation feature helps
alleviate issues of visibility in high contrast areas. Set the BLC
limit.
>> COLOR TEMP: Use
or
button to select a function.
--
INDOOR: The color temperature range for the proper
white balance is approximately 3 200 K.
--
OUTDOOR: The color temperature range for the
proper white balance is approximately 5 100 K.
>> RED: Set the desired red value.
>> BLUE: Set the desired blue value.
BRIGHTNESS
You can increase the brightness of the darkened video. If you set the
brightness to lower value, the image gets darkened. If you set the
brightness to higher value, the image gets bright.
1. Select [BRIGHTNESS] option on the [EXPOSURE] menu.
2.Use
or
button to set the bright level.
SHUTTER (Shutter Speed)
Select the desired shutter speed for camera exposure. You can
change the shutter speed to higher speed to capture fast-moving
subjects, though the image becomes darker.
1. Select [SHUTTER] option on the [EXPOSURE] menu.
2.Use
or
button to set shutter speed.
SENS-UP
If pictures are not clear due to darkness, this SENS-UP operation
would increase the sensitivity of picture.
1. Select [SENS-UP] option on the [EXPOSURE] menu.
2.Use
•
or
button to select a mode.
AUTO: Adjust the sensitivity of the picture automatically.
>> SENS-UP LIMIT: Use
SENS-UP limit.
or
button to set the
>> EXIT: Select a mode and click
28
button to exit the menu.
Operation and settings
Day/Night settings
3D-DNR setting
1. Select [DAY/NIGHT] option.
1. Select [3D-DNR] option.
2.Use
•
or
button to select a mode for DAY/NIGHT function.
AUTO: DAY/NIGHT mode changes automatically.
If pictures are not clear due to noise, this option would reduce
the noise of picture.
Note:
2.Use
If you set the AGC to [OFF] on the [EXPOSURE] menu, the
AUTO mode of the DAY/NIGHT function is not available and
[---] mark is displayed.
•
If you set the AGC to [OFF] on the [EXPOSURE] menu,
the [3D-DNR] function is not available and [OFF] mark is
displayed.
•
When you use this function, the afterimage may occur.
>> LEVEL: Use
or
>> DWELL TIME: Use
button to select a level.
or
button to select a dwell time.
•
DAY: Color mode enabled.
•
NIGHT: Black-and-white mode enabled.
or
button to select an option.
Note:
Privacy setting
This function is aiming at the protection of personal privacy. The
selected part is not displayed on the screen.
1. Select the [PRIVACY] option.
2.Use or button to select [ON] and press
SETUP menu appears.
. The PRIVACY
3.Use or button to select a zone number (AREA1 to AREA8)
on the [MASK NUMBER] option.
4.Use or button to set to ON or OFF on the [MASK STATE]
option. If you set to ON, the mask zone box appears on the live
window.
5.Use or button to select the color of the mask zone box on
the [MASK COLOR] option.
6.Use or button to select an option then use
to adjust the option.
or
button
•
WIDTH: Increase or decrease the horizontal size of the mask
zone box.
•
HEIGHT: Increase or decrease the vertical size of the mask
zone box.
7.Use
or
button to set to ON or OFF on the [GRID] option.
Note:
The parts with the registered mask numbers from AREA1 to AREA4
have the same color. (So do the parts with the numbers from AREA5
to AREA8.) If you change the mask color, the registered mask color
will be changed automatically with the same color for each of group
(AREA1 to AREA4, AREA5 to AREA8).
Operation and settings29
Special menu settings
A
>> Use , , or button to select a character or
number then click button.
FREEZE
1. Select the [FREEZE] option on the [SPECIAL] menu.
2.Use
or
button to set up the ON or OFF.
COLOR
button to change a color effect.
•
ON: To display the picture with color.
•
OFF: To display the picture with grayscale.
--
POS: Move the USER TITLE position on the screen
using the arrow buttons.
--
END: Confirm your selection or exit the setting.
--
1. Select the [COLOR] option on the [SPECIAL] menu.
or
CLR: Clear all entered characters and numbers.
-- A(Blank): Insert a space at the cursor position.
You can switch the displayed picture to gray scale or color.
2.Use
--
SHARPNESS
The degree to which the boundary of the two portions is clearly
distinguished.
1. Select the [SHARPNESS] option on the [SPECIAL] menu.
2.Use or button to adjust the option. If you set the sharpness
value to higher, the image outline becomes sharp. If you set to
lower value, the image outline becomes dim.
/
: Moves cursor to left or right.
•
ZOOM MAG: Displays or removes the zoom OSD on the
screen.
•
FUNCTION: Displays or removes the Function OSD on the
screen.
LANGUAGE
Select the viewer language for the camera setup menu and OSD
information display.
1. Select the [LANGUAGE] option on the [SPECIAL] screen.
2.Use
or
button to select the language
STABILIZER
The image stabilizer function minimizes the appearance of shaky
images caused by low-frequency vibration. This function is useful
for outdoor surveillance.
Select the [STABILIZER] option and set to ON or OFF.
Note:
If you set the [STABILIZER] to ON, the Digital zoom is set to [x1.1]
automatically.
OSD
You can set the Function On-Screen Display options using the [OSD]
menu. The Function On-Screen Display of this camera can be turned
on or off.
1. Select the [OSD] option on the [SPECIAL] menu.
2.Use or
appears.
button to select a [ON] and press
. The OSD menu
3.Use or button to select an option then use
to set the option.
•
or
button
USER TITLE: You can use the camera identification to assign a
number and character to the camera. To disappear the USER
TITLE, select [OFF].
>> Select the [USER TITLE] option on the [OSD] menu.
>> Use or button to select [ON] then click
The USER TITLE menu appears.
30
button.
Operation and settings
Reset setting
1. Select the [RESET] option.
2.Click
3.Use
button and the RESET menu appears.
or
button to select option.
•
FACTORY RESET: Clear certain settings and information and
return to factory default settings.
•
S/W VERSION: Displays the software version on the monitor.
4.Click
button to confirm your selection.
Operation and settings31
Reference
Troubleshooting
This section provides useful information to help you to resolve any difficulty you might have with your LG IP device. Fault symptoms,
possible causes and remedial actions are provided here.
IP Setting problems
•
ARP/Ping: Disconnect and reconnect the power to the network camera. The device should get the IP within 2 minutes.
•
Ping your camera: Open the command prompt on your computer, type ping with the IP address of the network device. The reply
obtained by this command provides explanation for the cause of the problem.
1. bytes = 32 time = 2 ms indicates that the IP address is already used and cannot reuse the same. A new IP address needs to be
obtained.
2. Destination host unreachable: indicates that the network device and your computer do not fall in the same subnet hence needs to
get a new IP address. Contact the system administrator for the required help.
3. Request timed out: Indicates that the IP is free as it is not used by anyone and the network device can obtain this.
•
IP Conflicts: If the LG network device is set with a static IP address and if the DHCP option is set then there may be IP’s same as the
network device and other network partner. Hence set the static IP address to 0.0.0.0 to resolve this conflict.
Cannot access the camera from browser:
•
Reconnect the network camera with power and check the ping operation to know if the IP is used by others.
•
Disable the proxy setting in the Browser if you are using a proxy server.
•
Check for proper cabling and network connections, try to ping after verifying the connectivity.
•
Sometimes when HTTPS is enabled, we would be checking the URL with http, in this case manually change the URL to the http/https
accordingly.
•
Verify the DNS and Gateway settings if the IP address is assigned statically to the network device.
•
If the browser you’re using or a page you’re viewing is displaying problems, try to clear the browser’s cache. If that doesn’t fix the
problem, try to clear the browser’s cookies.
Accessing camera external to the local network
•
Firewall Protection: Check for the internet firewall with the system administrator, either he has to do port forwarding or modify the DMZ
function on the router.
•
Default router needed: Check if you need configure the router settings.
Sporadic network performance
•
Network Switches or hubs used may be of the lower configuration and the load on this may not meet the required conditions of our
network camera.
•
Check for the RJ-45 cables that are used for the network connectivity.
•
If PoE is used check if the power is got by the network camera when connected to it.
Login Password lost
•
Reset the camera by shorting IP reset and GND terminal on multi-harness for more than 3 seconds to restore default settings.
•
After the factory settings login using the default user name and password.
Video Streaming problems
•
If the video streaming does not start on the Web browser, install the LG Web Client ActiveX program on your computer following the
instructions on the Web browser.
•
When Windows IE browsers are used always take care to allow pop ups, check this option before we run the web client.
•
Check the quality of image by referring the video settings as described in the manual.
•
Sometimes there would be intermittent or very slow video streaming, this may be because of the higher resolution and frame rate that
are set for the video.
•
The video streaming may appear poor at times, this may be because of the network traffic ,too many devices connected to the switch or
hub, enabling motion detection to each of the video streams and because of other programs running on your computer.
•
If the images appear to be blurred adjust the focus of the network camera to get a clear image.
•
Video images if appear white and black adjust the settings in the OSD to get back the colorful image.
•
Select the Night mode if the network camera is connected at a place where surrounding light is less or dark.
•
If we obtain lower frame rate than set we need to check from the system administrator for sufficient bandwidth available or reduce the
number of applications running on the client computer.
32Reference
•
If the client PC’s are unable to access the multicast stream, check with the system administrator for the use of a valid multicast address or
check if the router is supporting multicasting.
•
If the images appear to have white of gray stripes on it, upgrade the Video graphics driver on the client PC to the latest version.
•
Video images may be noisy if you are using the camera in a very low light environment or the bit rate/quality is set to very low values.
Provide higher values for quality and support the surrounding environment with enough light.
Audio condition
The client computer that is interacting with the camera needs to have a sound card that is functional to support speaker and microphone.
The sound card needs to be checked for its support for full duplex communication.
Ensure that the mute button of the client computer is not set and all the audio settings are correct.
Speaker button on the web viewer should be enabled to listen the audio from the network camera.
Ensure that the bidirectional audio button is enabled on the Web viewer and the microphone is set.
Change the input and the output gain for microphone and the speaker respectively to set correct audio level.
Clear browser’s Cache
•
If your browser is not working correctly after upgrade firmware. Please follow the below solution.
•
Solution: Deleting your browser’s cache may be resolved this issue.
1. Open Internet Options in browser Tools menu and click the [Delete Files] button in the second entry (Internet temporary files).
2. Check the other settings that should not be changed.
RCA output problem
•
RCA output use to initial installation.
•
Depending on the IP Camera usage scenario, RCA output video may not be smooth. It is used for initial installation only.
BNC output usage
BNC connector is for convenience of camera installation, and it is not suited to surveillance.
Power connection
•
It is recommended to use the power source either AC 24 V or PoE+.
•
PoE device must use PoE+. In case of the PoE, set the switcher to “PoE unused”.
(PoE+(IEEE 802. at-2009) : PoE Standard Provides up to 25.5 W of Power.
PoE(IEEE 802.3af-2003) : PoE Standard Provides up to 15.4 W of Power.)
For all further support please contact the supplier or forums or websites.
Open source software notice
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://
opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as
the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is valid for three (3) years from the date on
which you purchased the product.
Reference33
Specifications
Item
LW9422 Series
Image Sensor
6.49 mm (1/2.8 Type) CMOS Sensor
Total Pixels
1920(H) x 1080(V), 2M
Lens
F1.6(Wide) to F2.1(Tele), f=5.3 to 63.6mm
x12 Optical Zoom, x12 Digital Zoom
Day&Night
ICR Day & Night (Day / Night / Auto)
Minimum
Illumination (30IRE)
Color
1.0 lx (F1.6, Sens-up off ), 0.03 lx (F1.6, Sens-up x64)
B/W
0.1 lx (F1.6, Sens-up off ), 0.000 8 lx (F1.6, Sens-up x64)
White Balance
Auto / ATW / One Push / Manual
Shutter Speed
1/160 to 1/10 000
Iris
Auto / Manual
BLC
Off / WDR/ BLC
3D-DNR
OFF / LOW / MIDDLE / HIGH
AGC
OFF / LOW / MIDDLE / HIGH
Privacy Mask
8 Masks
Multi-Streaming
Dynamic Profile (Up to 7)
ROI (Region of Interest)
Support
Video Out
1xBNC
Resolution (Maximum)
Up to 1920 x 1080
Frame Rate (Maximum)
30 fps @ 1080p (1920 x 1080)
Bit Rate
256 kbps to 10 240 kbps
Audio Compression
G.711, G726
Audio In/Out
1/1
Sample Rate
8 KHz
Audio Bit Rate
G.711: 64 kbps, G.726: 24 kbps, 32 kbps
Ethernet
Protocol
10/100 Ethernet
IPv4 and IPv6
TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP
IPv4
FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS (LG)
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Remote S/W
LVi510, Mobile Application (iPhone, Android, iPad)
Pan/Tilt
Travel Range
Speed
Sensor / Alarm
Misc.
Pan : 360˚(Endless), Tilt : 180˚
Preset
500˚/second
Jog
0.1˚ to 360˚/second
Preset
256
Pattern
4 Patterns (760 command/Pattern)
Auto Pan
2 points to 8 points
Group
10 Groups (8 presets/Group)
Sensor
4 Inputs, Photo-Coupler Input
Alarm
2 Relay Outputs, Max Load : DC 30 V 1 A / AC 125 V 0.3 A
IP Module Reset Terminal
Support
Mount Accessory
Mount Adaptor
Material
Aluminum, Plastic sunshield
Rated Power
PoE+ / AC 24 V (49 W)
Waterproof
IP66, IK10
Fan
Always ON
Heater
Operation start from Internal Temperature 10˚C
Operation Temperature
-20 ˚C to 50 ˚C
Weight
3.3 kg
Dimension (Ø x H)
195 mm x 229 mm
34Reference
Item
LNP2810 Series
Image Sensor
4.5 mm (1/4 type) CMOS
Lens
x28 Zoom, f = 3.5 mm to 98 mm
Resolution (Maximum)
Up to 1280 x 720
Day&Night
ICR Day & Night (Day / Night / Auto)
Minimum
Illumination
Color
0.8 lx (F1.5, Sens-up off ), 0.16 lx (F1.5, Sens-up x32)
B/W
0.01 lx (F1.5, Sens-up off), 0.000 1 lx (F1.5, Sens-up x32)
White Balance
Auto / ATW / One Push / Manual
Shutter Speed
1/160 to 1/10 000
Iris
Auto / Manual
BLC
Off / WDR/ BLC
3D-DNR
OFF / LOW / MIDDLE / HIGH
AGC
OFF / LOW / MIDDLE / HIGH
Privacy Mask
8 Masks
Multi-Streaming
Dynamic Profile (Up to 7)
ROI (Region of Interest)
Support
Video Out
1xBNC
Frame Rate (Maximum)
30 fps @ 720p
Bit Rate
256 kbps to 10 240 kbps
Auto Tracking
No Support
Audio Compression
G.711, G726
Audio In/Out
1/1
Sample Rate
8 KHz
Audio Bit Rate
G.711: 64 kbps, G.726: 24 kbps, 32 kbps
Ethernet
10/100 Ethernet
Protocol
TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP
IPv4
FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS (LG)
ONVIF 2.2 Profile S, PSIA 1.1
Remote S/W
LVi510, Mobile Application (iPhone, Android, iPad)
Travel Range
Speed
Sensor / Alarm
Misc.
Support
IPv4 and IPv6
Open Protocol
Pan/Tilt
LNP2810T Series
Pan : 360˚(Endless), Tilt : 180˚
Preset
500˚/second
Jog
0.1˚ to 360˚/second
Preset
256
Pattern
4 Patterns (760 command/Pattern)
Auto Pan
2 points to 8 points
Group
10 Groups (8 presets/Group)
Sensor
4 Inputs, Photo-Coupler Input
Alarm
2 Relay Outputs, Max Load : DC 30 V 1 A / AC 125 V 0.3 A
IP Module Reset Terminal
Support
Mount Accessory
Mount Adaptor
Material
Aluminum, Plastic sunshield
Rated Power
PoE+ / AC 24 V (49 W)
Waterproof
IP66, IK10
Fan
Always ON
Operation Temperature
-20 ˚C to 50 ˚C
Weight
3.3 kg
Dimension (Ø x H)
195 mm x 229 mm
Reference35
Item
LNP3020T Series
Image Sensor
6.49 mm (1/2.8 type) CMOS
Lens
x30 Zoom, f = 4.3 mm to 129 mm
Resolution (Maximum)
Up to 1920 x 1080
Day&Night
ICR Day & Night (Day / Night / Auto)
Minimum
Illumination
Color
1.0 lx (F1.6, Sens-up off ), 0.02 lx (F1.6, Sens-up x64)
B/W
0.1 lx (F1.6, Sens-up off ), 0.000 8 lx (F1.6, Sens-up x64)
White Balance
Auto / ATW / One Push / Manual
Shutter Speed
1/160 to 1/10 000
Iris
Auto / Manual
BLC
Off / WDR/ BLC
3D-DNR
OFF / LOW / MIDDLE / HIGH
AGC
OFF / LOW / MIDDLE / HIGH
Privacy Mask
8 Masks
Multi-Streaming
Dynamic Profile (Up to 7)
ROI (Region of Interest)
Support
Video Out
1xBNC
Frame Rate (Maximum)
30 fps @ 1920 x 1080
Bit Rate
256 kbps to 10 240 kbps
Auto Tracking
Support
Audio Compression
G.711, G726
Audio In/Out
1/1
Sample Rate
8 KHz
Audio Bit Rate
G.711: 64 kbps, G.726: 24 kbps, 32 kbps
Ethernet
10/100 Ethernet
Protocol
IPv4 and IPv6
TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP
IPv4
FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS (LG)
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Remote S/W
Pan/Tilt
LVi510, Mobile Application (iPhone, Android, iPad)
Travel Range
Speed
Sensor / Alarm
Misc.
Pan : 360˚(Endless), Tilt : 180˚
Preset
500˚/second
Jog
0.1˚ to 360˚/second
Preset
256
Pattern
4 Patterns (760 command/Pattern)
Auto Pan
2 points to 8 points
Group
10 Groups (8 presets/Group)
Sensor
4 Inputs, Photo-Coupler Input
Alarm
2 Relay Outputs, Max Load : DC 30 V 1 A / AC 125 V 0.3 A
IP Module Reset Terminal
Support
Mount Accessory
Mount Adaptor
Material
Aluminum, Plastic sunshield
Rated Power
PoE+ / AC 24 V (25 W)
Waterproof
IP66, IK10
Fan
Always ON
Operation Temperature
-20 ˚C to 50 ˚C
Weight
3.3 kg
Dimension (Ø x H)
195 mm x 229 mm
36Reference
Item
6.40 mm (1/2.8 type) CMOS
Lens Type
X30, 4.3 mm to 129 mm, F1.6-F5.0
Minimum Illumination
Camera
PTZ
Video / Audio
Event
Interface
Network
General
LNP3022 series
Image Device
LNP3022T series
Color: 0.3 lx (F1.6, AGC High, Sens-up off, 30IRE)
B/W: 0.01 lx (F1.6, AGC High, Sens-up off, 30IRE)
Day/Night
ICR (Auto / Day / Night)
WDR
Support
Image Enhancement
Backlight Compensation, HSBLC, 2D+3D-DNR, Exposure Control, Sens-UP Control,
AGC, White Balance, Privacy Masking, EIS, Sharpness, Auto Digital Zoom, De-fog
Optical Zoom
X30
Panning Range & Speed
0˚ to 360˚, Maximum 500˚ / second
Tilting Range & Speed
0˚ to 180˚, Maximum 500˚ / second
Auto Panning
2 to 8 points
Preset/ID
256
Group Touring
Maximum 10 Groups
Pattern
4
Auto Tracking
No Support
Video Compression
H.264, H.264_High, MJPEG
Resolution
1920 x 1080 / 1280 x 720 / D1 (704 x 480) / CIF (352 x 240)
Maximum Frame Rate
30 fps (1920 x 1080)
Multi-Streaming
Up to 7
ROI (Smart-Codec)
Crop (Up to 4)
Video Analytics
Motion detection
Text Overlay
Support
Audio Compression
G.711, G.726
2-way Audio
Support
Event Trigger
Video analytics, Alarm input
Event Notification
Relay Out, Email, FTP, Go to Preset
Pre Event Buffering
Support
Analog Out
BNC out
Audio In/Out
1 In / 1 Out
Alarm In/Out
4 In / 2 Out
SD Slot
SD (Up to 32 GB)
Ethernet
RJ-45 10/100BASE-T
Security
Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Protocol
Support
IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP, QoS, UPnP
IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
Integrated Software
LG Ipsolute VMS Suite / Mobile application (iPhone, iPad, Android)
Connections
Up to 10
Power Source
AC 24 V, PoE+
Maximum Power Consumption
25 W
Operation Temperature/
Humidity
-20 ºC to 50 ºC / 0 % RH to 80 % RH
Protection
IP66, IK10
Dimension (Ø x H)
195 mm x 229 mm
Weight
3.3 kg
Reference37
Download PDF

advertising