LG | LNU7210RH | LG LNU7210RH Owner’s Manual

OWNER’S MANUAL
Network
Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODELS
LNB7210
LNB5110
LND5110
LNV7210
LND7210
LNV5110R
LND5110R
LNU5110R
LNV7210R
LND7210R
LNU7210R
LNV7210RH
LNU7210RH
1504 (V1.9)
Contents
Introduction.................................................................................... 3
Features Chart.........................................................................................3
Operation and settings.................................................................. 4
Before using the system......................................................................4
Recommended PC Requirements....................................................4
Accessing the LG IP device.................................................................5
LG Smart Web Viewer Overview.......................................................6
Configuration menu overview...........................................7
Configuring the LG Network Camera Device...............................7
Accessing the Configuration menu..................................7
System settings........................................................................8
Audio & Video settings.......................................................11
Network settings..................................................................19
User settings..........................................................................22
Event settings........................................................................23
Reference...................................................................................... 28
Troubleshooting..................................................................................28
OPEN SOURCE SOFTWARE NOTICE ..............................................29
Specifications.......................................................................................30
2
Introduction
The LG Network Camera is designed to use on an Ethernet network and must be assigned an IP address to make it accessible.
This manual contains instructions on how to install and manage the LG Network Camera in your networking environment. Some knowledge
of networking environments would be beneficial to the reader.
Note that design and specification of this unit may change from the manual as quality and improvement without prior notice.
Should you require any technical assistance, please contact authorized service center.
Features Chart
This table shows the differences between the models.
Item
RS-485
Zoom
Focus
External Day/Night
LNB7210
Yes
No
Auto Back Focus (ABF)
Yes
LNB5110
Yes
No
No
Yes
LND5110
No
Yes
Auto Focus
Yes
LNV5110R
No
Yes
Auto Focus
Yes
LND5110R
No
Yes
Auto Focus
Yes
LNU5110R
No
Yes
Auto Focus
Yes
LNV7210
No
Yes
Auto Focus
Yes
LNV7210R
No
Yes
Auto Focus
Yes
LND7210
No
Yes
Auto Focus
Yes
LND7210R
No
Yes
Auto Focus
Yes
LNU7210R
No
Yes
Auto Focus
Yes
LNV7210RH
No
Yes
Auto Focus
Yes
LNU7210RH
No
Yes
Auto Focus
Yes
Introduction3
Operation and settings
Before using the system
Recommended PC Requirements
•
Before using the LG IP device make sure the connections are
correct and verify whether proper power supply is used.
The LG IP device can be used with most standard operating systems
and browsers.
•
Check the connections of the LG IP device for the correct
conditions.
•
Check that the LG IP device is(are) connected to the network
and that power is supplied.
•
Once the connections are made you need to install the LG client
program to the PC from which you want to access the device.
The LG Smart Web Viewer program is automatically installed
when you connect the LG IP device.
The LVi510 and the LG Smart Web Viewer program are the
network program of the LG Video Server and the LG IP cameras.
•
To view streaming video in Internet Explorer, set your browser
to allow ActiveX controls. If you find this message “This website
wants to install the following add-on: ‘IPCam_Streamer.cab’ from
‘LG ELECTRONICS INC’”, Click the yellow bar and install LG Smart
Web Viewer Program on your computer. Please set your browser
zoom level to 100%.
•
The Layouts and the Live view pages may differ with different
OS (Operating Systems) and Web Browsers.
•
Care needs to be taken not to run any other applications when
the Client Program is running as it may cause memory shortage.
•
When you set on 60 fps in mobile applications, may be
degraded the frame rate depending on mobile performance.
•
If you connect to the power of LNU7210RH and LNV7210RH
under -10 ºC, It takes up to 10 minutes for warming up.
“Warming up” message is displayed on the screen.
Items
Operating System
CPU
Web Browser
Requirements
Windows XP Professional,
Windows VISTA, Windows 7
Intel Core2 Quad Q6700 (2.66 GHz) or
above
Microsoft Internet Explorer (32 bit) above
the version 7.0 and below the version 9.0.
DirectX
DirectX 9.0c (Windows XP),
DirectX 11 (Windows Vista/7) or above
Memory
2 GB or above RAM
Graphics Card
Resolution
256 MB or above Video RAM
2048 x 1536 (with 32 bit color) or higher
Note:
For Windows 7, please download & install ‘DirectX End-User Runtime
Web Installer’.
“http://www.microsoft.com/en-us/download/details.aspx?id=35”
Note:
It is recommended to connect the power of LNU7210RH and
LNV7210RH over -35 °C. After connecting, the camera can
operate with temperatures until -40 °C.
4
Operation and settings
Accessing the LG IP device
You can access the LG IP device by following the below steps.
1.
3.
Logging in to the LG Smart Web Viewer
3.1
Run the IP Utility and find the LG IP devices.
3.2
When the LG IP devices appear in the IP Utility
window, double-click IP address or right click on the
same IP address and select “Connect to Web Page”
to start the LG Smart Web Viewer. When accessing
the LG Smart Web Viewer, the window for login will
be shown. Select the language in drop-down list on
right top of the window.
3.3
Enter the user name and password. (Note that the
default administrator user name and password are
“admin”.)
Install LVi510 Program
It recommended to use LVi510 surely.
Otherwise, it is required to install the IP Utility
[Package>Tools>LG IP Utility Installer] to search the IP
addresses of LG IP devices.
2.
Discover the LG IP device using the IP Utility
The IP Utility can automatically discover and display LG IP
devices on your network.
The IP Utility shows the MAC address, IP address, Model
name and so on.
Note:
The computer running the IP Utility must be on the same
network segment (physical subnet) as the LG IP device.
2.1
Run the IP Utility program.
2.2 Click the [Search] button or select the [Search]
option in the Device search menu.
After a few seconds the found LG IP devices gets
displayed in the IP Utility window.
Note:
Default password must be changed for security after
initial connection.
Note:
•
You can also access the LG Smart Web Viewer as shown
below.
3.1 Start your Web browser.
3.2 Enter the IP address of the LG IP device in the
address bar of the browse.
3.3 Enter the user name and password set by the
administrator.
•
Check the browser cookies settings to use the
[Remember my credentials].
•
If LG Smart Web Viewer is required to be updated, it
needs more time to display according to the network
conditions.
•
If you connect the LG Smart Web Viewer for the first
time, the Security Warning window is displayed to install
the LG Smart Web Viewer program. You must install the
LG Smart Web Viewer program for using the LG IP device.
•
If your computer or network is protected by a proxy or
firewall, the proxy or firewall settings can prevent the LG
Smart Web Viewer program. Change the proxy or firewall
settings to activate the LG Smart Web Viewer program.
Operation and settings5
LG Smart Web Viewer Overview
Click to effect and then check the check
box of [Edge Enhancement] option. The
user gets more sharp reception on the
live view window.
Note:
This feature only affects the live view
window.
Click to save the current image in JPEG
format on your computer.
1. Click the [Snapshot] button and then
the Snapshot window is displayed.
2. Click the [Save] button in the
Snapshot window.
Item
Description
Select the video image size from the
drop-down list.
(FULL SCREEN / AUTO RESIZE / x0.5 / x1
/ x2 / D1 / CIF)
Note:
•
Select [FULL SCREEN] to enlarge
full screen of monitor. To return
previous screen, press ESC key or
double click.
•
When you select [AUTO RESIZE], size
of live view screen fit to window.
Ratio imaging is fixed by width and
height based.
•
When you change view size option
larger on high resolution image,
browser function may not work
smoothly.
It displays Video Codec, Resolution, FPS
and Preset Mode of the selected video
stream.
4. Click the [Save] button to confirm it.
5. Click the [Cancel] button in the
Snapshot window to close it.
Note:
It is not displayed the area of MD and
SVA in Snapshot file.
Displays the PTZ (PAN / TILT / ZOOM)
control window.
Note:
•
The Zoom / Focus adjustment is
recommended during installation
only. If you adjust the Zoom / Focus
after completed the install, the
screen is changed and feature set
may behave differently.
•
LNB7210 / LNB5110 are not
supported the PTZ control.
LND5110 / LNV5110R / LND5110R
/ LNU5110R / LNU7210R /
LNU7210RH are supported the
Zoom / Focus only.
Check this option as the network
connection type (TCP or UDP). If you
check it, the client connects to the
server using TCP connection.
Select the video stream. From the Live
view drop-down list, select the desired
video image source.
Select buffering time of live stream.
You can set the stream configurations
independently. This would facilitate the
user to set the live view at his comfort.
Click to display the check box of
[Hostname], [Framerate] and [Bitrate]
options. Select the [Position] on [Display]
menu. (Top Left / Top Right)
Video Analysis
>> Hide: Video Analysis display
function is not in use.
>> SVA: Displays the Smart Video
Analysis function to the live view
window.
>> MD: Displays the Motion
Detection function to the live
view window.
Note:
6
3. Enter the file name (JPEG format) and
select the folder to save it.
•
While the [Pivot] is activated,
on Profile2, Profile3 and Profile4, MD
is available when a profile is set to
the same codec with Profile1.
•
When you use the DPTZ function, all
of Display function is deactivated for
a while.
Note:
Provides all the necessary tools
for setting up the device to your
requirements. The user will need
administrator level to do this.
Note:
If you want to exit the Configuration
menu, select one of the video stream in
the Live view drop-down list or click LG
Smart IP Device icon.
Displays the current surveillance live
screen. You can monitor the camera
image on the live view window of the
LG Smart Web Viewer.
Operation and settings
Click this button and drag the area to
use Digital PTZ function. Right-clicking
the screen will bring up the previous
magnification.
(Color icon: On, Gray scale icon: Off.)
1. Click this button to open the folder
browse window. Click the button
again in next time, video is recorded
automatically without selection of
folder.
Configuration menu overview
The following table shows the list of menu items.
The configuration images are different from each model.
Main Menu
System
Note:
•
If you want to change the folder,
move to other pages or press the
refresh button.
•
When the Profile is changed,
a new route storage folder is
selected.
Audio & Video
2. Recording button is activated and
recording will be started.
Note:
If recording exceed the time (1 hour)
or size limit (1 GB), recording is
stopped automatically with warning.
Network
3. To stop the recording, click this
button during the recording.
Click this button to switch the sound
off and on, for the speaker of the
computer.
(Color icon: On, Gray scale icon: Off.)
Basic
Event server
Sensor & Relay
Motion Detect
Event
Audio detect
Smart Analytics
Triggered Event
Note:
(Color icon: On, Gray scale icon: Off.)
Option
Option
802.1x
User
(Color icon: On, Gray scale icon: Off.)
When the audio is enabled both In and
Out, microphone can be available to
select the On/Off.
Note
QoS
Click this button to connect or
disconnect the audio communication
between the LG IP device and the
connected PC.
Click this button to switch the
microphone off and on for the
computer.
Sub Menu
Version
Date & Time
Maintenance
Storage
Text Overlay
Log & Report
Language
Camera
Stream
Audio
PTZ config
Preset
Basic
RTP stream
TCP/IP
DDNS
IP filtering
SNMP
Scheduled Event
Configuring the LG Network Camera
Device
The features and options of the LG IP camera are configured
through the Configuration menu.
Only administrator-level users have permission to access the
Configuration menu.
Accessing the Configuration menu
Click the [Configuration] button to display the LG Smart Web Viewer
configuration window.
Warning
The Configuration setup should be made by qualified service
personnel or system installers.
Operation and settings7
System settings
Maintenance
Version
Displays the current Model Name, Software, ISP and MCU version.
System reboot
Click the [Reboot] button to restart the IP device. It takes some
minutes for the IP device to start again.
Note:
Click OSS(Open source software) link to check the information
about Open source software. Refer to the [OPEN SOURCE
SOFTWARE NOTICE] of [Reference].
Backup and restore
>> Backup: To take a backup all of the settings. If necessary, it
make possible to return to a backup configuration.
1. Click the [Backup] button.
2. Click the [Save] button.
Date & Time
3. Follow the instructions on the browser to specify the
folder.
4. Click the [Save] button to save the settings.
>> Restore:
1. Click the [Browse] button.
2. Find and open the file in which the configuration setting
data is stored.
3. Click the [Restore] button and the system settings will be
restored and reboot the system.
Note:
Backup and Restore can happen on IP device having the
same version of firmware. This feature is not intended for
multi-configurations or for firmware upgrades.
Time zone
Set the time difference from GMT in the area where the IP device
is installed. Select the time zone in the area where the IP device is
installed from the drop down list.
Firmware
>> Upgrade
Time mode
1. Click the [Browse] button.
>> Synchronize with NTP Server: Select if you want to
synchronize the IP device’s date and time with those of the
time server called NTP (Network Time Protocol). Specify the
NTP server’s name. Click the [Test] button for connection
test to the server.
2. Find and open the firmware file.
3. Click the [Upgrade] button to update the firmware.
Note:
When you upgrade the system, it may take some minutes
to be done. Do not close the browser while the upgrade
is in progress. If you close the browser, it may cause a
malfunction. You should wait until the confirmation window
is displayed. When the upgrade is finished, the confirmation
window will be displayed.
>> Synchronize with personal computer: Select if you want
to synchronize the IP device’s date and time with your
computer.
>> Synchronize manually: Select if you want to set the IP
device’s date and time manually. Select the year, month and
date by clicking the calendar button. Set hour, minutes and
seconds in the edit boxes.
Note:
•
When system reboot after time setting, time of system
could be delayed. If you set the time correctly, set the
[Synchronize with NTP server] option.
•
Refer to NTP configuration as operation system of
the Recording Server when the Recording Server use
recording function and NTP server.
>> Initialize: The [Initialize] button should be used with caution.
Clicking it will return all of the IP device’s settings to the
factory default values. Except for the Network settings, PTZ
Protocol and Preset settings. (The option depends on the
model.)
Note:
Refer the “Clear browser’s Cache” of Troubleshooting.
Server time
>> Server time: Displays the current date and time of the IP
device.
•
Save: Click this button to confirm the settings.
8
Operation and settings
Storage
>> Remove the micro SD card
1. Click the [Unmount] button. If the micro SD card is
unmounted from the system correctly, the [Unmount]
button will be changed to the [Mount] button.
2. Remove the micro SD card from the micro SD card slot of
the camera.
Note:
When you use the Unmount function, it may not progress
immediately. Operations such as recording of the system
and reading of data are required stop time before the
Unmount function is activated. You should try it again after
waiting a few minutes.
File Format
>> File Format: You can selects the Recording File Format(AVI
or DAT). Recording, Search and Download are available
according to the setting.
General
>> Overwrite: If the micro SD card has insufficient space and
this option will be activated. It will overwrite the oldest data.
Note:
>> DiskFull Notification: Sends an warning e-mail to the SMTP
server when the micro SD card has fully recorded. Select the
SMTP server from the drop-down list. You should register
the SMTP server on the Event server setting to set this
function.
>> Network Failure Recording: Select the check box to activate
the micro SD card recording function. If the system does
not work with recording server, the system will record the
data to the micro SD Card. When the system connect to the
recording server again, the recorded data of the micro SD
card will transfer to the recording server automatically.
•
SD Recording or FTP(Video) Sending Format are set
according to the setting. When you select to AVI, [Auto
Recording function] may not be activated in case of
network error.
•
IP Camera’s time will be appeared in players based on
DirectShow such as Windows Media Player and MPlayer.
File Management
Displays the recorded file of the micro SD card on the list. Click the
[Search] button to display the recorded file. The list will be updated
when you click the [Search] button.
>> Recording Server IP: Enter the recording server IP.
>> To view the recorded file of the micro SD card
>> Set as NTP server IP: Click this button to use the entered
Recording Server IP as the NTP server IP.
1. Select the search option.
Note:
•
The recorded file name is made automatically as the
“[Created date of the file]_[GMT Recording Time].DAT”
type.
•
If the capacity of the SD card remains less than 200 MB,
stop recording or overwrite new file after delete old one
as [Overwrite] setting. The overwritten file can not play
or may malfunction when you download.
•
Recorded file on the SD card, is recording 1 frame per
second when set video codec to MJPEG.
All: Search the all recorded files in the micro SD card.
--
Some: You can set the search condition by using the
date and time options.
2. Click the [Search] button and then the search result is
displayed on the list.
>> Download: You can download the recorded data of the
list to your PC. Select a recorded file on the list and click
the [Download] button. The two confirmation window
is displayed. You should download the all files that the
recorded file(*.DAT) and information file(*.INFO). You can
download as AVI file according to File format.
Note:
Device Management
>> Using the micro SD card
•
It is recommended to deactivate the [Overwrite]
function before you download the file. When [Overwrite]
function is activated, the downloading file might be
overwritten, if the micro SD card has insufficient space.
•
The downloaded file can be played by using the LG File
player.
1. Insert the micro SD card carefully to the micro SD card
slot of the camera.
2. Click the [Mount] button. If the micro SD card is mount­
ed to the system correctly, the [Mount] button will be
changed to the [Unmount] button.
3. Displays the information of the[Disk ID], [Status],
[Capacity] options.
--
>> Remove: Delete file from the SD card.
•
Save: Click this button to confirm the settings.
Note:
•
When the micro SD card is mounted, you should format
the micro SD card. After the micro SD card format is
finished, you should click the [Mount] button to use it.
•
When you use the micro SD card format function, it may
not progress immediately. In this case, you should try it
again after waiting a few minutes.
Operation and settings9
Text Overlay
>> Multi-Line Text: Enter characters in the text field. Maximum
input characters are depends on the resolution.
--
Applicable model: LND5110 / LNB5110 / LNV5110R /
LND5110R / LNU5110R
Capture Mode
Font Size
0
1
2
3
--
Preview
You can preview the camera image on the preview window.
Mode
>> Multiline Mode: Set more characters, color and size of the
text overlay by selecting the [Multiline Mode]. The saved
text overlay is displayed on the left top of screen.
4:3 or 5:4
Column
Row
32
16
32
16
24
16
18
12
Applicable model: LNB7210 / LNV7210 / LND7210 /
LNV7210R / LND7210R / LNU7210R / LNV7210RH /
LNU7210RH
Font Size
0
1
2
3
>> Normal Mode: Follow the normal procedure of text overlay
option by selecting the [Normal Mode].
16:9
Column
Row
32
12
32
12
24
12
18
9
Column
32
32
32
27
Row
16
16
16
13
Basic Configuration
>> Color: You can make any color by adjusting R.G.B LEVEL.
When you select the [Normal Mode], you can adjust the
[Date&Time], the [Text Information], the [X position], the [Y position]
and the [User Title] function. And other functions are able to adjust
by selecting the [Multiline Mode].
>> Size: You can adjust the font size.
>> Transparency: You can adjust the background transparency
of text .
Note:
>> Date&Time: Click the check box of [Date&Time] to display
time and date of Client PC.
>> Text Information: Enter characters in the text field. (From
[Text1] to [Text2]) Maximum input characters are depends
on the resolution.
--
Applicable model: LND5110 / LNB5110 / LNV5110R /
LND5110R / LNU5110R
Capture Mode
16:9
4:3 or 5:4
--
Column
24
24
If you change the [CaptureMode], the existing characters
may not be seen partially.
•
The [Multi-Line Text] is an one off feature. When refresh a
browser to connect this option again, the text input field
of [Multi-Line Text] is cleared but contents of text overlay
are remained on a live view screen.
•
If you use below features, text overlay is changed
[Normal Mode] :
[System>Maintenance>Reboot],
[Audio & Video>Camera>Install>CaptureMode],
[Audio & Video>Camera>Install>Install Preset],
[Audio & Video>Camera>Install>WDR],
[Audio & Video>Camera>Install>Sensor Framerate]
•
Text can be blurred depending on background scene
and codec quality. In this case, you can set the text area
as the Smart Codec.
Row
12
16
Applicable model: LNB7210 / LNV7210 / LND7210 /
LNV7210R / LND7210R / LNU7210R /
LNV7210RH / LNU7210RH
Column
27
•
Row
13
>> X Position: Set the horizontal position of each text overlay.
•
Save: Click this button to confirm the settings.
>> Y Position: Set the vertical position of each text overlay.
>> User Title: Enter the user title. The user title is displayed on
the right bottom of screen.
10
Operation and settings
Log & Report
Audio & Video settings
Camera
Preview
(Applicable model: LNB7210 / LNB5110)
You can preview the camera image on the preview window.
Note:
The preview screen may differ depending on models.
Log & Report status
The System log provides a summary of the status of the IP device.
The unit records the data of the software activity in a file.
>> View Log: Click this button to display the system log
information.
--
Download: Click this button to see the log information
of system.
>> View report: Click this button to display the report of the
system.
--
Download: Click this button to see the report
information of system.
Note :
The downloaded file is a UNIX type. If you open the file in Microsoft
Notepad, it will display the text as if the file contained no line breaks
at all.
Language
Preview
(Applicable model: LND5110 / LNV5110R / LND5110R / LNU5110R /
LNV7210 / LND7210 / LNV7210R / LND7210R / LNU7210R /
LNV7210RH / LNU7210RH)
1. Move the camera to the point you want by using the arrow
buttons.
2. Adjust the zoom, focus options.
3. Set the Pan, Tilt, Zoom or Focus step options. (LND5110 /
LNV5110R / LND5110R / LNU5110R / LNU7210R / LNU7210RH
are not supported the PAN and TILT function.)
Note:
•
Focus Push : To save the final location after the Auto Focus
operation is performed.
•
Except for [Focus Push], the location of the lens is not stored. If
the power is turned off or restart the software, the lens may not
move to the final location.
•
Press and hold the direction button, the camera moves
continuously until you release the button, after move one step
as long as set value. Depending on the set step value, PTZ
movement can be flinch for a second.
Install
Language list
Select a language for the LG Smart Web Viewer configuration menu
and information display.
•
Save: Click this button to confirm the settings.
>> Install Preset: Select the Install Preset mode from the dropdown list.
Note:
•
Privacy Mask settings are initialized every time Pivot
Mode is selected or deselected.
•
It is displayed the constraints according to preset
settings by mouse-over at the right-top of the
drop-down list box.
Install
Preset
Quad
Stream
Sensor
Framerate Pivot
Video
Out
WDR
Max
Streams
25 or 30
Off
Off
On /
Off
4
Triple
Stream
25 or 30
(Default)
Off
NTSC /
PAL /
Off
On /
Off
3
Operation and settings11
Pivot
25 or 30
On
Off
On /
Off
3
High
Framerate
50 or 60
Off
Off
Off
2
Focus (Applicable model: LND5110 / LNV5110R / LND5110R /
LNU5110R / LNV7210 / LND7210 / LNV7210R / LND7210R / LNU7210R /
LNV7210RH / LNU7210RH)
>> Capture Mode (Applicable model: LND5110 / LNV5110R /
LND5110R / LNU5110R / LNB5110): Select the capture mode.
Capture Mode
16:9
4:3 or 5:4
Resolution
1280 x 720
1280 x 1024
Note:
If you change the Capture Mode option, the Privacy settings
on the OSD menu is initialized.
>> Sensor Framerate: Select the Sensor Framerate value.
Note:
•
FPS maximum value cannot exceed the value of Sensor
Framerate.
•
Pivot, Video out, WDR, Max Stream Count are limited,
depending on the Install Preset setting.
•
You need to reset the Motion Detect and Smart Analytics
in Event menu every time Pivot Mode is selected or
deselected.
--
Zoom Trig: After the change of the zoom position,
camera is performed autofocus once. Also the manualfocusing is enable too.
>> Video Out: Select the video standard of the camera from the
drop down list.
--
Manual: Use , , , ,
focus position manually.
>> WDR: WDR (Wide dynamic range) feature can be very
helpful to cope with very challenging lighting conditions. It
is capable of capturing both of the dark part and bright part
and combining the differences into a scene to generate a
highly realistic image as original scene.
--
Focus Push: This function will be activated automatically
to adjust the focus.
--
Focus Save: Save the position of Zoom and Focus at the
moment of click this button. The focus moves to the
stored position even if the camera is reset.
--
Focus Reset: If the abnormal operating occurs or the
camera is out of focus by external shocks or other
reasons, click this button to initialize the lens and return
to the current location.
Note:
>> Mode: Select [Mode] option on the [Focus] menu, then
select the following mode.
When the WDR is running, [Dynamic Range Enhancer]
is operated and [Minimum Shutter Speed] is adjusted
automatically.
or
button to adjust the
>> EIS: The image stabilizer function minimizes the appearance
of shaky images caused by low-frequency vibration. This
function is useful for outdoor surveillance. Select the [EIS]
option and set to [On] or [Off ].
Note:
•
After installation, the focus may be twisted by external
shocks. In this case, press the [Focus Reset] button to
initialize the lens.
>> D-Effect: You can select the digital effect.
•
Click , , , , or
button to move once within a
narrow range. And the movement range depends on a
shape of , ,
buttons.
--
Mirror: Turn on the mirror effect.
--
V-Flip: Flip the picture vertically.
Note:
•
Video codec settings should be set to H.264 or
H.264_HIGH to operate the EIS and Pivot function.
•
When you change the settings of [Install Preset],
[Sensor Framerate] and [WDR] system may be rebooted
or video may be disconnected temporary.
•
The [Mirror] and [V-Flip] function can be selected at
once.
•
In the [Pivot] mode, the Text Overlay is rotated 90
degrees counterclockwise to the output. It is not
affected of the Mirror and V-Flip.
•
Install settings will be updated at the time of entering
the Install tab.
•
Save: Click this button to confirm the settings.
•
Default: Click this button to restore the IP device back to original
factory settings.
12
>> Day/Night AF: You can set the AF function when the
Day/Night mode is converted.
--
High / Medium / Low : Select [High], [Medium] or [Low]
of the AF operating range. When [High] is selected, the
widest AF operating range is set.
--
OFF: Not used the AF function when the Day/Night
mode is converted.
>> Night Offset (Applicable model: LNV5110R / LND5110R /
LNU5110R / LNV7210RH / LNU7210RH): Adjust the focus
manually in the night mode of Day/Night function. Adjust
the value by moving the handle or pushing the arrow
button.
Note:
•
100 is the standard value. The closer the value is to 200,
the further the focusing distance will be, and the closer
to 0, the nearer.
•
When the Day/Night function is converted to day mode,
the focus will be returned to previous position.
•
It will be highly efficient when it is hard to focus with
[Day / Night AF] function.
Operation and settings
Focus (Applicable model: LNB7210)
Exposure
>> Auto: Select [Auto] option on the [Focus] menu, then select
the following mode.
--
Focus Push: This function will be activated automatically
to adjust the focus.
--
Focus Reset: The focus position is located at factory
default position.
--
Manual: Use , , , ,
focus position manually.
or
button to adjust the
Note:
•
When you mount the lens, press [Focus Reset] button to
reset your focus.
•
After adjusting the focus approximately,
press [Focus Push] button to adjust the lens sharply into
focus.
>> Day/Night AF: You can set the AF function when the
Day/Night mode is converted.
--
--
High / Medium / Low : Select [High], [Medium] or [Low]
of the AF operating range. When [High] is selected, the
widest AF operating range is set.
OFF: Not used the AF function when the Day/Night
mode is converted.
>> IRIS: Select the desired lens iris value for camera exposure.
Select [IRIS] option on the [Exposure] menu, then select a value.
--
Auto: The lens iris is set automatically.
--
Manual: Select this option when use the lens for
adjusting IRIS manually.
Note:
When the [Manual] is selected, IRIS is fixed on full open
state. In this case, adjust the brightness by shutters.
>> BLC: Camera’s backlight compensation feature helps
alleviate issues of visibility in high contrast areas.
Note:
When the [WDR] is set to [On], the BLC is deactivated.
>> Dynamic Range Enhancer: Adjusts the contrast of the image
automatically to provides bright and clear images.
Note:
When the [WDR] is set to [on], the [Off ] option of [Dynamic
Range Enhancer] is deactivated. It adjusts the level of the
[WDR].
>> De-Fog: Select the value to remove the misty fog of image.
Note:
If the [De-fog] function operates while the [WDR] is turned
on, occurs only the simple effects as On/Off without
a difference in the operating level (High/Middle/Low).
Because the WDR includes the auto-adjust De-fog.
>> AGC: If the images are too dark, change the maximum [AGC]
value to make the images bright.
>> Brightness: Adjust the brightness of images.
>> Shutter Speed: Select the desired shutter speed for camera
exposure. You can change the shutter speed to higher speed
to capture fast-moving subjects, though the image becomes
darker.
Note:
When the [WDR] is set to [on], [Minimum] is deactivated and
adjusted automatically.
1/10 000 1/5 000 1/2 500 1/1 500 1/1 000
Minimum
Shutter
1/700
1/500
1/480
1/400
1/360
1/300
1/250
1/240
1/180
1/150
1/120
1/100
1/60
1/50
1/30
1/25
Operation and settings13
1/10 000 1/5 000 1/2 500 1/1 500 1/1 000
Maximum
Shutter
1/700
1/500
1/480
1/400
1/360
1/300
1/250
1/240
1/180
1/150
1/120
1/100
1/60
1/50
1/30
1/25
1/20
1/15
1/8
1/4
1/2
2/3
1
1.5
2
White Balance
>> Flickerless: Remove the band noise caused by fluorescent
light.
Note:
When the [IRIS] is set to [Manual], if the surrounding area is
bright, can be seen flicker even if the [Flickerless] is set.
In this case, set the [IRIS] to the [Auto].
•
Default: Click this button to restore the IP device back to original
factory settings.
>> Mode: Select [Mode] option on the [White Balance] menu,
then select the following mode.
--
Auto: Adjust the white balance of the full image area.
Use this function in the environment by special lighting
lamp.
Note:
When a monochromatic object is caught on camera, the
object may seem faded.
In case of this, it is recommended to set to [ATW] mode.
--
Manual: You can set the white balance options manually.
If the [Mode] option set to [Manual], [Red] and [Blue] are
displayed.
--
ATW (Auto-Tracing White Balance): Adjust the white
balance by tracing the white area.
In the following conditions, may not work properly:
1. When the scene contains mostly high color
temperature objects, such as a blue sky or sunset.
2. When the scene is dim.
--
ONE PUSH: If you select the [ONE PUSH] mode, you will
be able to set up the White Balance automatically.
>> Red: Set the desired red value.
>> Blue: Set the desired blue value.
>> Color Temp: If the [Mode] option set to [ATW], this option is
displayed. Click to select the option.
•
14
--
Indoor: Adjust the white balance according to the indoor
environment.
--
Outdoor: Adjust the white balance according to the
outdoor environment.
Default: Click this button to restore the IP device back to original
factory settings.
Operation and settings
Day/Night
•
Set the type of [Sensor] according to External Sensor
type. The Day/Night mode is converted as below table.
Sensor Type
Normal Open
Normal Close
•
>> Mode: Select [Mode] option on the [Day/Night] menu, then
select the following mode.
--
Auto: [Day/Night] mode can be changed to the [Auto]
mode depending on the [Level] settings.
--
Day: Maintains the color mode always.
--
Night: Maintains the Black-and-white mode always.
--
External: The Day/Night mode is converted by using
Alarm In Port.
--
Schedule: Operates as the [Day] mode during set time.
Alarm
Mode
High
Day
Low
Night
High
Night
Low
Day
•
If the difference of value between the [Day >> Night]
and [Night >> Day] is not big enough, may occur the
problem to convert the Day and Night.
•
When the [AGC] set to [Off ], the [Day/Night] is initialized
to the [Day] mode. Other settings of [AGC] are initialized
to the [Auto] mode.
Default: Click this button to restore the IP device back to original
factory settings.
>> To set the schedule
1. Select the [Schedule] option. The detail options are
displayed.
2. Select the check box of options.
•
All: Operates as the [Day] mode every day during set
time.
•
Sunday - Saturday: You can set the time for each day
of the week. For days of week which are not selected,
it operates as [Auto] mode.
•
Save: Click this button to save the schedule setting.
>> Level: Adjust the automatic conversion time according to
the ambient light. If you select the [High], conversion is
made in the lowest illuminance.
>> User Level: When you select the [Level] option to [User],
you can adjust the automatic conversion time according to
the ambient light. The left handle set the value of [Night >>
Day] and the right handle set the value of [Day >> Night].
>> Dwell Time: Set the time to maintain the brightness for the
automatic conversion.
Note:
•
When you set to [External] mode, the [Sensor] function
of [Triggered Event] will be deactivated.
•
In case of [External] mode, you should set to [Enable]
from the [Sensor&Relay > Sensor] option.
Operation and settings15
SmartIR (Applicable model: LNV7210R / LND7210R / LNU7210R /
LNV7210RH / LNU7210RH)
Image
>> Noise Reduction: If pictures are not clear due to noise, this
option would reduce the noise of picture. When you use this
function, the afterimage may occur.
SmartIR (Applicable model: LNV5110R / LND5110R / LNU5110R)
>> Color Saturation: Set the intensity of the color.
>> Sharpness: The degree to which the boundary of the two
portions is clearly distinguished. If you set the sharpness
value to higher, the image outline becomes sharp. If you set
to lower value, the image outline becomes dim.
>> Privacy Mask
--
Add: Click the [Add] button.
1. When you click on the preview screen, yellow cross
point is displayed.
2. Click again to make another point. The point is
connected as sky blue line from previous point.
Note:
•
--
Auto: When the [Day/Night] menu set to [Night]
mode, the brightness of the IR LED will be adjusted
automatically. The [Max Level] is displayed.
When you select all of 4 points, area is set
automatically.
•
--
Manual: When the [Day/Night] menu set to [Night]
mode, the brightness of the IR LED will be fixed.
To set the Privacy Mask area, each four vertex must
be convex. If the one of 4 vertex is inside to make
concave area, the Privacy Mask area will not be set.
•
--
Off: When the [Day/Night] menu set to [Night] mode, IR
LED will be turned off.
You can cancel the point by click the mouse right
button near the other point.
•
Up to 4 zone is available to set.
>> Mode
--
Delete: Delete the selected zone.
--
Delete All: Delete all of the mask zone.
Note:
--
Save: Save the settings of the Privacy Mask.
When set the [IRIS] to the [Manual], the [Auto] mode is
deactivated.
Note:
>> Max Level: If the [Mode] option set to [Auto], can be adjust
the maximum brightness of IR LED.
>> Level: If the [Mode] option set to [Manual], can be adjust the
fixed brightness of IR LED.
•
Default: Click this button to restore the IP device back to original
factory settings.
•
16
•
If the privacy mask setting is changed , it is not applied
immediately. You need to click the [Save] button to save
the settings.
•
When the [Image] tab is selected, the Privacy Mask area
is displayed on the preview window.
•
Set the [Privacy Mask] after complete the [Install]
settings.
•
Privacy Mask settings area is not maintained by the
screen change by the operation of Pan / Tilt / Zoom.
When reset the Pan / Tilt / Zoom, you need to reset the
Privacy Mask settings area also.
•
If the [D-Effect] is changed, the [Privacy Mask] settings
will be initialized.
•
The [EIS] and [Privacy Mask] can not be used at the same
time.
Default: Click this button to restore the IP device back to original
factory settings.
Operation and settings
Stream
20
15
10
5
4
3
2
1
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
>> GOP size: It means “Group of Pictures”. The higher the GOP,
the better is the video quality of the camera. Set the value
of GOP from 1 up to 60 depending on Install Preset settings.
This setting is valid for H.264 video format only.
Profile
Select the stream [Profile1], [Profile2], [Profile3] or [Profile4]
depending on Install Preset.
>> Quality: Select the Quality.
Note:
--
It is displayed the constraints according to the current preset
settings by mouse-over at the right-top of the current Preset.
VBR: The bit rate may vary depending on the complexity
of the video to meet the selected quality.
--
CBR: The video quality may vary in order to preserve a
constant bit rate.
--
Applicable model: LND5110 / LNV5110R / LND5110R /
LNU5110R / LNB5110
Profile
Quad
Stream
Triple
Stream
Profile1
SXGA @
30 fps
SXGA @
30 fps
SXGA @
30 fps
SXGA @
60 fps
Pivot
High
Framerate
--
Profile2
SXGA @
30 fps
D1 @ 30 fps
Profile3
SXGA @
30 fps
SXGA @
30 fps
>> Smart Codec: You can improve the image of specific area
to configure the Region or Face Detect. If you select the
[Region] option, the [Smart Codec (Region)] window is
activated.
Profile4
CIF @ 30 fps
Note :
N/A
•
D1 @ 30 fps CIF @ 30 fps
N/A
When the video codec is H.264 or H.264_HIGH, the
Smart Codec can be selected.
•
D1 @ 60 fps
N/A
Two areas can overlap and the sum of the two areas
have to be less than 30 % of the total area.
•
Smart Codec settings area is not maintained by the
screen change by the operation of Pan / Tilt / Zoom.
When reset the Pan / Tilt / Zoom, you need to reset the
Smart Codec settings area also.
N/A
Applicable model: LNB7210 / LNV7210 / LND7210 /
LNV7210R / LND7210R / LNU7210R /
LNV7210RH / LNU7210RH
Profile1
Profile2
Profile3
Profile4
1 080P @
1 080P @
720P @
CIF @ 30 fps
30 fps
15 fps
30 fps
Quad
Stream
1 080P @
720P @
720P @
CIF @ 30 fps
30 fps
30 fps
30 fps
1 080P @
1 080P @
720P @
N/A
30 fps
15 fps
30 fps
Triple
Stream
1 080P @
720P @
720P @
N/A
30 fps
30 fps
30 fps
1 080P @
N/A
N/A
N/A
30 fps
1 080P @
720P @
Pivot
CIF @ 30 fps
N/A
15 fps
30 fps
720P @
720P @
CIF @ 30 fps
N/A
30 fps
30 fps
1 080P @
N/A
N/A
N/A
60 fps
High
Framerate
720P @
D1 @ 60 fps
N/A
N/A
60 fps
>> Enable: Click to activate the stream function.
>> Stream quality: If the [Quality] option set to VBR, this
option is displayed. Select the stream quality from the drop
down box, the camera supports five types. (Highest, High,
Medium, Low and Lowest)
Profile
>> Bit rate: If the [Quality] option set to CBR, this option is
displayed. If the Profile is set to [Profile1], can be set the
Bitrate value from 1 024 kbps to 10 240 kbps. In case of
[Profile2], [Profile3], [Profile4], can be set from 256 kbps to
10 240 kbps.
Note:
If the ‘Bit rate’ is configured too low with high resolution,
the actual frame rate will decrease because of narrow
bandwidth. So you need to set or change the ‘Bit rate’ to
high value.
JPEG Snapshot Quality
>> Snapshot Quality: Select the quality of JPEG snapshot.
•
Save: Click this button to confirm the settings.
>> Video codec: Select the video mode (Codec) from the dropdown list. The viewer can choose among MJPEG, H.264 and
H.264_HIGH.
>> Resolution: Select the resolution from the drop-down list.
>> Maximum frame rate: Set the frame rate of the image.
Note:
Refer to the table below for the supported Framerate.
If you enter the unsupported framerate, the less Encoding
Framerate than the input is applied.
For example, when 17 fps is entered, 15 fps will be applied.
Encoding
Framerate
60
50
30
25
60
O
O
O
O
Sensor Framerate
50
30
N/A
N/A
O
N/A
O
O
O
O
25
N/A
N/A
N/A
O
Operation and settings17
Audio
PTZ config (Optional)
Audio In
>> Enable: Click the check box if you want to send the audio
from the microphone input connector.
PTZ protocol list
>> PTZ protocol: Displays the selected PTZ protocol.
Note:
The Clients connected to the IP device remain unaffected
with additional changes made in the setting.
PTZ configuration
>> Input: Select the type of audio input. (Line in, Microphone)
>> Camera ID: Enter the PTZ device ID. Make the same ID as the
PTZ Device.
>> Audio type: Select the type of audio encoding.
(G711 PCMA, G711 PCMU, G726 24K, G726 32K)
>> Pan speed: Enter the panning speed of the PTZ device in the
edit box.
>> Tilt speed: Enter the tilting speed of the PTZ device in the
edit box.
Audio Out
>> Enable: Click the check box to output the audio from the
speaker.
>> Zoom speed: Enter the zoom speed of the PTZ device to
view the object close or at a distance.
Note:
Depending on the camera and Network condition, it may
delay for a few seconds.
•
Save: Click this button to confirm the settings.
>> Focus speed: Enter the focus speed of the PTZ device to
focus an object clearly near or far.
Port
>> Baud rate: Select the desired speed of communication
between the IP device and the PTZ Device. Confirm selected
parameter to the baud rate of the IP device.
>> Data bit: Set the number of the data bits for RS-485
communication.
>> Parity: Select the desired parameter. The parity bit, added to
the data, to perform parity check.
>> Stop bit: Enter the desired parameter. The stop bit, added to
the last of data, in asynchronous communication.
•
18
Save: Click this button to confirm the settings.
Operation and settings
Preset (Optional)
Network settings
Basic
Preset
Displays the registered preset position.
1. Move the camera to the point you want by using the arrow
buttons.
2. Set the Pan, Tilt, Zoom or Focus step options.
>> Add: Click to add a preset position.
General
>> MAC address: Displays the MAC address.
Port & Encryption
>> Network encryption: Select the HTTP or HTTPS option for
security.
1. Enter the preset index and speed.
2. Click the [Add] button.
>> Smart Port Setting: Select [On] to allocate a port number
automatically.
>> Remove: Click to delete the preset position.
1. Select the preset from the list.
Note:
2. Click the [Remove] button. The preset will be deleted.
If you select [On], [UPNP Status], [External IP], [Web Port] and
[RTSP Port] options are deactivated.
>> Go to preset: Move to the preset position.
>> UPNP Status: When you use the router that is supported
UPNP function, you can set the port forwarding
automatically by using the [Smart Port Setting]. [UPNP
Status] shows connected status of router.
1. Select the preset from the list.
2. Click the [Go to preset]. The camera will be moved to the
selected preset.
Note:
>> External IP: When you connect the router that is supported
UPNP function, this option is displayed. Displays the external
IP address allocated router.
RS-485 is connected or not, [Focus Push] and [Save] function always
work.
>> Web port: The default HTTP port number (80) can be changed
to any port within the range 1 025 to 65 535.
>> RTSP port: Check RTSP port. The default port is 554. Other
ports can be selected within the range 1 025 to 65 535.
Note:
The RTSP port number should not be same with the web
port number.
ARP ping
>> Enable ARP ping to configure IP address: Check to enable
ARP ping.
•
Save: Click this button to confirm the settings.
Operation and settings19
RTP stream
TCP/IP
RTP (Real-time Transport Protocol) is an internet protocol that allows
programs to manage the real-time transmission of multimedia data,
via unicast or multicast.
IPv4 address status
Profile
>> Automatically set with DHCP: Select this option when a
DHCP server is installed on the network to allow IP address
assignment. With this setting, the IP address is assigned
automatically.
>> RTP unicast: When enabled the transmission of the data to
the specified equipment happens on a network specifying a
single address.
--
>> RTP multicast: When enabled it reduces the transmission
load on the camera by making the computer of the same
segment network receive the same transmission data. When
multicast option is checked then select Video Port number,
Audio Port number and Data port number.
--
IPv4 address: Set the IP address for RTP multicast.
--
Base RTP port: Enter the port number of even number
used for the multicast streaming. Each profile uses
successive 6 port number which starts from [Base RTP
port]. It is initially set to 10 000 and you can edit this
between 10 000 and 65 530.
Note:
Note:
Video codec settings should be set to H.264 or H.264_HIGH to
operate the Motion-Control FPS.
•
Each profile using multicast needs its own multicast IP address
and port numbers to avoid address conflict. When more than
2 profiles use same multicast IP address, each [Base RTP port]
number should be distinguished from the other port number
more than 6 at least.
Multicast
•
You should register the SMTP server on the Event server
setting to set this function.
•
If you select [Automatically set with DHCP], the camera
obtain IP address from DHCP server after IP address is
set “192.168.0.16”.
>> Statically set: Select this option when you set a fixed IP
address, with this setting, specify the IP address, Subnet
mask and default gateway manually.
>> Motion-Control FPS: If there is movement, the Framerate is
adjusted automatically.
•
--
IPv4 address: Enter an IP address.
--
Subnet mask: Enter a subnet mask address.
--
Gateway: Enter the gateway address.
DNS server status
>> Primary DNS server: Enter the Primary domain name server
that translates the hostnames into IP address.
>> Secondary DNS server: Enter the Secondary DNS server
address that backups the Primary DNS.
IPv6 address status
>> Enable: Click the check box if you want to use the IPv6
address.
>> Always Multicast: Check to enable multicast regardless of
client connection.
>> Mode
TTL
>> TTL: This option indicates the Time-To-Live of multicast
packets. The default setting is 7, and the allowed TTL range
is from 1 to 255.
--
Manual: Select this option when you set a fixed IP
address manually.
--
Basic: Select this option to allow IPv6 address
assignment based on the Mac address. With this setting,
the IP address is assigned automatically.
--
DHCPv6: Select this option when exist a DHCPv6 server
in network. If DHCPv6 server is not existed or temporary
disability, it requests assignment every 3 minutes.
IP Fragmentation
>> IP Fragmentation: Check to enable IP fragmentation.
When the VMS is not supported the IP Fragmentation,
uncheck this feature.
•
Notify to SMTP server, if IP address is changed: If you
select this option, the user get a notification mail telling
about changing of IP of the IP device.
Save: Click this button to confirm the settings.
>> IPv6 address: You can enter the IP address when you select
the Manual mode. It alarms when you enter the invalid IP
address.
•
20
Save: Click this button to confirm the settings.
Operation and settings
DDNS
Note:
This free service is very useful when combined with the LG DDNS
Server. It allows the user to connect the IP device using the URL,
rather than an IP Address. This also solves the problem of having a
dynamic IP address.
If you want to deny or to allow a range of IP addresses, enter
the start IP address to “From” and the end IP address to “To”.
You can also add an IP address by entering the same IP
address to “From” and “To”.
3. Click the [Save] button.
4. Repeat the steps 1 to 3 to add additional IP address.
•
Remove: Click this button to delete the IP address.
1. Select the alias from the list.
2. Click the [Remove] button. The IP address will be deleted.
IPv6 address
•
Add: Click this button to add the IP address.
1. Click the [Add] button.
2. Set the IP address option.
DDNS status
>> Don’t use DDNS server: Disable the DDNS function.
>> Use DDNS server: Enable the DDNS function.
•
--
Provider: Displays the DDNS provider.
--
Hostname: Enter the hostname you want to use.
--
Alias: Enter the alias.
--
IPv6 address: Enter the IP address for IP filtering.
3. Click the [Save] button.
4. Repeat the steps 1 to 3 to add additional IPv6 address.
•
Save: Click this button to confirm the settings.
Remove: Click this button to delete the IPv6 address.
1. Select the alias from the list.
2. Click the [Remove] button. The IPv6 address will be deleted.
IP filtering
The access of the IP addresses in the list are allowed or denied
according to the choice made in the drop-down list of the Basic
policy option. The administrator can add up to 10 IP address entries
to the list (a single entry can contain multiple IP addresses). The
users from these IP addresses need to be specified in the user list
with the appropriate access rights. The IP list is to control the access
permission of clients by checking the client IP address.
SNMP
The Simple Network Management Protocol (SNMP) is an application
protocol to exchange the management information of network
devices.
SNMP v1/v2c
>> Enable SNMP v1/v2c: Selects when SNMP is allowed access
to this device.
>> Read Community: Specifies the SNMP management
community in which you want to read this system.
>> Write Community: Specifies the SNMP management
community in which you want to write this system.
SNMP v3
>> Enable SNMP v3: Selects when SNMP v3 is allowed access to
this device. It supports authentication and encryption.
IP list
>> Basic policy: Select the basic policy type.
---
>> SecurityName: Type the security name for the SNMP.
Allow all: Allow all the IP address basically, but the IP
addresses in the list are denied.
Deny all: Deny all the IP address basically, but the IP
addresses in the list are allowed. It needs at least one IP
address to activate this function.
•
Save: Click this button to confirm the settings.
•
Add: Click this button to add the IP address.
>> Password: Type the password for the SNMP.
•
Save: Click this button to confirm the settings.
1. Click the [Add] button.
2. Set the IP options.
--
Alias: Enter the alias.
--
From: Enter the start IP address for the IP filtering.
--
To: Enter the end IP address for the IP filtering.
Operation and settings21
User settings
QoS
You can specify network Quality of Service (QoS) settings.
Basic
The IP device is shipped with the login rights of administrator only.
If others need to access the IP device excluding the configuration a
login with viewer rights need to be created. A maximum of 50 users
can be created.
QoS DSCP Configuration
>> Video DSCP: Enter the priority of Video for DSCP
(Differentiated Service Code Point) Quality of Service.
>> Audio DSCP: Enter the priority of Audio for DSCP Quality of
Service.
>> Event DSCP: Enter the priority of Event for DSCP Quality of
Service.
•
Save: Click this button to confirm the settings.
User list
>> Add the User
You can register a new user with various access rights.
802.1x
Specifies whether 802.1x network access is enabled.
1. Click the [Add] button. User setting dialog is displayed.
2. Enter the new User ID and Password. (Should have a
minimum of 4 characters and preferably a combination
of alphanumeric.)
3. To confirm the password, retype the password that you
typed in the Password box.
4. Select the authority from the drop down list to provide
the access rights to each user and then click the [Save]
to confirm your selection.
--
Administrator: Allows you to operate setup menus
and to view live images.
--
Power user: Use of the limited functions of the
system. (The Configuration menu is not allowed.)
A power user can use the Live View, OSD control and
audio functions.
--
Normal user: Provides the lowest level of access,
Allows to view live images only.
--
Custom user: The user can login and view the live
stream image only when the “Enable anonymous
login” option is checked to enable it.
802.1x/EAPOL using EAP-TLS
>> Enable: Select on to enable the protocol. Current
authorization status of 802.1x port is displayed on buttons
right.
Certificates
>> To upload or remove the certificates
1. Click the [Browse] Button.
2. Find and open the certificates file.
--
CA Certificate: Upload the accredited certificate included
public key.
--
Client Certificate: Upload the accredited certificate
included client authentication key.
--
Client private key: Upload the accredited certificate
included client private key.
•
Remember the password.
•
Displayed Items according access authority are
like below:
Admin
Power
User
Normal User /
Custom User
PTZ
O
O
X
3. Click the [Upload] button to install certificates.
DPTZ
O
O
X
4. Click the [Remove] button to delete certificates.
REC
O
O
X
BI-AUD
O
O
X
Basic Configuration
>> EAPOL Version: Select the EAPOL version.
>> EAP ID: Enter the ID of the client certificate using up to 16
characters.
>> Password: Enter the password of the client private key using
up to 16 characters.
•
Note:
Save: Click this button to confirm the settings.
MIC
O
O
X
SPEAKER
O
O
X
SETTINGS
O
X
X
>> Edit the registered user
You can change the password or authority.
1. Choose the user ID and then click the [Edit] button.
2. Change the Password or Authority, then click the [Save]
button to confirm your selection.
22
Operation and settings
Event settings
>> Delete the registered user
1. Choose the user ID you want to delete.
2. Click the [Remove] button.
Event server
Note:
Event Servers are used to receive the recorded video clip and/or
notification messages.
The default administrator user ID ‘admin’ and ‘anonymous’
are permanent and cannot be deleted.
Anonymous
>> Enable anonymous login
Check the box to enable anonymous user login - allows the
user access for only viewing the live stream image.
Maximum RTP stream connection
>> Maximum number of simultaneous stream connection:
Set this number to limit the number of simultaneous stream
connections.
The connections depend on the stream configuration as
shown in the following Maximum RTP stream connection by
stream configuration.
--
Applicable model: LND5110 / LNV5110R / LND5110R /
LNU5110R / LNB5110
Video Codec
Resolution
Frame
Rate
H.264_HIGH
1280 x 1024
30
Maximum
Quality
RTP
stream
HIGHEST Up to 20
H.264
1280 x 1024
30
HIGHEST
Up to 20
MJPEG
1280 x 1024
10
HIGHEST
Up to 14
--
Applicable model: LNB7210 / LNV7210 / LND7210 /
LNV7210R / LND7210R / LNU7210R /
LNV7210RH / LNU7210RH
Video Codec
Resolution
Frame
Rate
H.264_HIGH
1920 x 1080
30
Maximum
RTP
stream
HIGHEST Up to 20
H.264
1920 x 1080
30
HIGHEST
Up to 20
MJPEG
1920 x 1080
10
HIGHEST
Up to 14
Quality
Note:
Preview window of the IP device setting and preset setting
are affected by this setting.
•
Save: Click this button to confirm the settings.
FTP server list
Image files can be transferred to the FTP server within the
scheduled time. Image file that has been recorded linked to an
external event is sent to the FTP server periodically.
>> To add the FTP server
1. Click the [Add] button. FTP server setting window is
displayed.
2. Set the FTP server options.
--
Alias: Type the FTP Server name to upload the image
files.
--
Address: Enter the FTP server’s IP address.
--
Port: Enter the port number. The default FTP port is
21.
--
User ID: Type the user name for the Folder shared in
the FTP server.
--
Password: Type the password for the folder shared in
the FTP Server.
--
Folder: Type the path with the folder that is shared in
the FTP server.
--
Test: Select [Test] to test the FTP server.
3. Click the [Save] button to confirm the settings.
>> To edit the FTP server
1. Choose the FTP server in the FTP server list.
2. Click the [Edit] button.
You can check or edit the FTP server options.
>> To delete the FTP server
1. Choose the FTP server in the FTP server list.
2. Click the [Remove] button. This would remove the FTP
server from the list.
SMTP server list
By selecting the e-mail option, a still image of the event is captured
and an e-mail with the attached image file is sent to the specified
mail address.
>> To add the SMTP server
1. Click the [Add] button. SMTP server setting window is
displayed.
2. Set the SMTP server options.
--
Alias: Enter the SMTP server name.
--
User ID: Enter the user ID of the SMTP server. This
would be the one who owns the mail account.
--
Password: Enter the password of the SMTP server.
--
Address: Enter the SMTP server address.
--
Port: Enter the port number. The default port is 25.
--
Enable SSL: Check when use the SSL (Secure Socket
Layer) protocol. SSL protocol is cryptographic
protocols that provide secure communication on a
Operation and settings23
network.
--
Receiving address: Type the recipients e-mail
address. You can specify only one recipient e-mail
address.
--
Administrator address: Type the e-mail address of
the administrator.
--
Subject: Enter the subject/title of the e-mail.
--
Message: This message can describe the information
of the acquired IP address, etc.
--
Test: Select [Test] to test the SMTP server.
3. Click the [Save] button to confirm the settings.
Sensor & Relay
Sensor
>> To edit the SMTP server
>> Enable: Marks up when you want to activate the sensor.
1. Choose the SMTP server in the SMTP server list.
>> Alias: Displays the sensor name.
2. Click the [Edit] button.
You can check or edit the SMTP server options.
>> Type: Select the sensor type.
>> To delete the SMTP server
Relay
>> Control duration: Enter the relay time.
1. Choose the SMTP server in the SMTP server list.
>> Alias: Displays the relay name.
2. Click the [Remove] button.
>> Type: Select the relay type.
>> Control relay
•
--
Run: Click to activate the relay.
--
Stop: Click to stop the relay.
Save: Click this button to confirm the settings.
Note:
The number of Sensor and Relay are depending on the model.
24
Operation and settings
Motion Detect
Audio detect
Audio Detection
Preview
You can preview the motion detection window on the preview
window.
>> Enable: Set to [ON] or [OFF]. The Basic Configuration menu is
displayed when selects [ON].
Basic Configuration
>> Level: Select the level of audio detection from the
drop-down list. You can set the level using by jog control.
If you use jog control, the [Level] option is set to [Manual]
automatically.
General
>> Sensitivity: Enter the sensitivity to detect an object in
motion.
•
>> Input Graph: Displays at intervals 0.5 seconds within 25
seconds cumulative graph.
Save: Click this button to confirm the settings.
>> Audio Detect Status: Displays the audio is detected or not.
How to set the motion detect window
1. Click the [Add] button. The motion detect window is
displayed. You can add the three windows maximum for
motion detection area.
2. Set the [Sensitivity] option.
3. Click the edge or corner of the window box to adjust the
window size for motion detection.
•
Save: Click this button to confirm the settings.
Smart Analytics
4. Click the [Save] button to save the settings.
Note:
•
Created motion detection area window will be applied for the
same sensitivity at once.
•
Increase the sensitivity in the environment with a low lighting
condition or a few motion. On the contrary, in the environment
with a high lighting condition or a lot of motion, decrease the
sensitivity.
•
The Motion Detection function may not work depending on
your installation environment.
•
Motion Detection settings area is not maintained by the screen
change by the operation of Pan / Tilt / Zoom. When reset the
Pan / Tilt / Zoom, you need to reset the Motion Detection
settings area also.
•
You can reset the window size. Click one of the window edge or
corner and drag & drop to reset the motion detection area.
•
Motion Detection can be activated when at least one of
channels is enabled, Video codec is set to H.264 and GOP size is
more than 2.
Preview
You can preview the camera image on the preview window.
Basic Configuration
>> Tamper Detect: Detect changes on the screen and operate
in accordance with the registered Event.
--
Enable: Set to [On] or [Off ].
>> Face Detect: Detect the recognized face on the screen and
operate in accordance with the registered Event.
--
Enable: Set to [On] or [Off ].
--
Sensitivity: Set the [Sensitivity] option.
Note:
When the value is closer to the [Highest] detects
sensitively, and when the value is closer to the [Lowest]
detects insensitively.
Operation and settings25
Additional Detect (Available up to three)
>> To set the detect area
1. Set to [ON] the desired algorithm.
Triggered Event
When an event (VA/ Motion detect/ Sensor Event/Audio detect)
occurs, this unit records the live images and routes as configured.
2. Click the [Set Zone] or [Set Line] button.
3. Click the left mouse button on the screen to set the detect
area.
--
Intrusion: When the perceived object is(are) move into
the event area, the Intrusion Event is activated.
--
Object Removal: When the object is disappear from the
setting area, the Object Removal Event is activated.
--
Object Desertion: When the object is placed in the
setting area, the Object Desertion Event is activated.
--
Crossing Line: When the perceived object go through a
setting lines, the Crossing Line Event is activated.
--
Object Counting: When the perceived object go through
a setting line, the Object Counting Event is activated.
4. Click the [Save] button to confirm the settings.
Event schedule list
>> To edit the Event Schedule
1. Select the Trigger event and click the [Edit] button. Event
schedule window is displayed.
2. Set the options.
Note:
•
It is possible to set in area up to octagon from triangle, and
can be set only convex polygon.
Trigger: Display the selected trigger event and the
current state of trigger. Current state of trigger is
Displayed to On or Off.
•
•
To finish the area setting, click right mouse button. In case of
octagon, it is finished to click the last point.
Time: Sets the weekday, Start, Finish, Pre alarm, Post
alarm and Ignore interval time options.
•
•
While set an area, if you click the right mouse button over
the point, the point is canceled.
Action: Selects the options. This occurs when the
event runs.
•
In case of [Intrusion], [Object Removal], [Object Desertion]
algorithms can set the detect area and [Crossing Line],
[Object Counting] algorithms can set the direction of
detection.
•
When detection occurs, the text is displayed at the right of
detection configuration. (“Detected” or “Not Detected”)
•
When the area setting and activating of [Object Removal]
and [Object Desertion] are finished, detection will start in
10 seconds to set the initial background.
•
[Object Removal] and [Object Desertion] are activated
when the detected object is being in same condition
for 10 seconds.
•
[Object Removal] and [Object Desertion] need up to
5 minutes to recognize the object as the background.
•
You can select an algorithms up to 3.
•
•
26
Depending on your installation environment, it may occur
detection error or performance degradation of image
analysis.
•
--
FTP(Video) server/SMTP server: Uploading of
images to an FTP server, or e-mail notification.
--
Control relay: The relay is activated or
deactivated.
--
SD Card recording: Record on the SD card when
the event runs.
--
Move camera to (Applicable model: [Sensor] in
LNB7210): Write the number of the preset, the
camera would Move to this preset when the relay
is activated.
--
FTP server(JPEG): Sends the JPEG Image to
the FTP server. Image file and suffix setting is
available. You can select Date/Time or Sequence
of Suffix.
Stream: Selects the stream of the connected camera.
3. Click the [Save] button to confirm the settings.
Note:
•
You should register the SMTP and FTP server on the
Event server setting to set this function.
•
Recording of event(VA/ Motion detect/ Sensor Event/
Audio detect) runs every 5 minutes split file.
•
Used stream is profile1(1st) in case of FTP(JPEG)
transmission.
•
When the [External] mode in [Day/Night] menu is used,
the [Sensor] is deactivated.
Operation and settings
Scheduled Event
Activation Time
>> Always : You can use always by using the FTP server
regardless of activation time.
>> Only scheduled time: Continuously record according to the
set time and the selected weekday. Drag and drop with left
button of the mouse to set the channel and time you want
to record.
Action
Set the below option.
>> SD Card recording : Record to SD Card when event occurs.
Selects the camera stream for SD card recording.
>> FTP server(JPEG) : Upload the image or send the e-mail to
the FTP server. Send Image per, Base File Name and Suffix
setting are available.
Note:
•
•
You can select through drag of Activation Time table
that is possible to select according to weekday and time.
•
Used stream is profile1(1st) in case of FTP(JPEG)
transmission. If always checkbox next to FTP(JPEG) is
checked, FTP(JPEG) is always enable regardless of the
activation time.
Save: Click this button to confirm the settings.
Operation and settings27
Reference
Troubleshooting
This section provides useful information to help you to resolve any difficulty you might have with your LG IP device. Fault symptoms,
possible causes and remedial actions are provided here.
IP Setting problems
•
ARP/Ping: Disconnect and reconnect the power to the network camera. The device should get the IP within 2 minutes.
•
Ping your camera: Open the command prompt on your computer, type ping with the IP address of the network device. The reply
obtained by this command provides explanation for the cause of the problem.
1. bytes = 32 time = 2 ms indicates that the IP address is already used and cannot reuse the same. A new IP address needs to be
obtained.
2. Destination host unreachable: indicates that the network device and your computer do not fall in the same subnet hence needs to
get a new IP address. Contact the system administrator for the required help.
3. Request timed out: Indicates that the IP is free as it is not used by anyone and the network device can obtain this.
•
IP Conflicts: If the LG network device is set with a static IP address and if the DHCP option is set then there may be IP’s same as the
network device and other network partner. Hence set the static IP address to 0.0.0.0 to resolve this conflict.
Cannot access the camera from browser:
•
Reconnect the network camera with power and check the ping operation to know if the IP is used by others.
•
Disable the proxy setting in the Browser if you are using a proxy server.
•
Check for proper cabling and network connections, try to ping after verifying the connectivity.
•
Sometimes when HTTPS is enabled, we would be checking the URL with http, in this case manually change the URL to the http / https
accordingly.
•
Verify the DNS and Gateway settings if the IP address is assigned statically to the network device.
•
If the browser you’re using or a page you’re viewing is displaying problems, try to clear the browser’s cache. If that doesn’t fix the
problem, try to clear the browser’s cookies.
Accessing camera external to the local network
•
Firewall Protection: Check for the internet firewall with the system administrator, either he has to do port forwarding or modify the DMZ
function on the router.
•
Default router needed: Check if you need configure the router settings.
Sporadic network performance
•
Network Switches or hubs used may be of the lower configuration and the load on this may not meet the required conditions of our
network camera.
•
Check for the RJ-45 cables that are used for the network connectivity.
•
If PoE is used check if the power is got by the network camera when connected to it.
Login Password lost
•
Reset the camera by pressing the Reset button for more than 3 seconds to restore default settings.
•
After the factory settings login using the default user name and password.
Video Streaming problems
•
If the video streaming does not start on the Web browser, install the LG Web Client ActiveX program on your computer following the
instructions on the Web browser.
•
Internet Explorer may not display the image normally depends on the ActiveX version. In this case, check the Internet Explorer settings
for ActiveX.
•
When Windows IE browsers are used always take care to allow pop ups, check this option before we run the web client.
•
Check the quality of image by referring the video settings as described in the manual.
•
Sometimes there would be intermittent or very slow video streaming, this may be because of the higher resolution and frame rate that
are set for the video.
•
The video streaming may appear poor at times, this may be because of the network traffic ,too many devices connected to the switch or
hub, enabling motion detection to each of the video streams and because of other programs running on your computer.
•
If the images appear to be blurred adjust the focus of the network camera to get a clear image.
•
Video images if appear white and black adjust the settings in the OSD to get back the colorful image.
•
Select the Night mode if the network camera is connected at a place where surrounding light is less or dark.
•
If we obtain lower frame rate than set we need to check from the system administrator for sufficient bandwidth available or reduce the
number of applications running on the client computer.
28Reference
•
If the client PC’s are unable to access the multicast stream, check with the system administrator for the use of a valid multicast address or
check if the router is supporting multicasting.
•
If the images appear to have white of gray stripes on it, upgrade the Video graphics driver on the client PC to the latest version.
•
Video images may be noisy if you are using the camera in a very low light environment or the bit rate / quality is set to very low values.
Provide higher values for quality and support the surrounding environment with enough light.
Audio condition
The client computer that is interacting with the camera needs to have a sound card that is functional to support speaker and microphone.
The sound card needs to be checked for its support for full duplex communication.
Ensure that the mute button of the client computer is not set and all the audio settings are correct.
Speaker button on the web viewer should be enabled to listen the audio from the network camera.
Ensure that the bidirectional audio button is enabled on the Web viewer and the microphone is set.
Change the input and the output gain for microphone and the speaker respectively to set correct audio level.
Browser’s problems
When you have a problem with browser, press the [Refresh] button on your browser window.
Clear browser’s Cache
•
If your browser is not working correctly after upgrade firmware. Please follow the below solution.
•
Solution: Deleting your browser’s cache may be resolved this issue.
1. Open Internet Options in browser Tools menu and click the [Delete Files] button in the second entry (Internet temporary files).
2. Check the other settings that should not be changed.
•
If the browser you’re using or a page you’re viewing is displaying problems, try to clear the browser’s cache. If that doesn’t fix the
problem, try to clear the browser’s cookies.
RCA output problem
•
RCA output use to initial installation.
•
Depending on the IP Camera usage scenario, RCA output video may not be smooth. It is used for initial installation only.
BNC output usage
BNC connector is for convenience of camera installation, and it is not suited to surveillance.
For all further support please contact the supplier or forums or websites.
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit
http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as
the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is valid for three (3) years from the date on
which you purchased the product.
Reference29
Specifications
Item
Camera
Video / Audio
Event
Interface
Network
LNB7210
Image Device
6.4 mm (1/2.8 Type) CMOS
Lens Type
CS mountable
Day / Night
ICR (Auto / Day / Night / External / Schedule)
Minimum Illumination
Color: 0.03 lx (F1.2, Gain : High, 1/30 sec, 50 IRE)
B/W: 0.003 lx (F1.2, Gain : High, 1/30 sec, 50 IRE)
WDR
Support
Focus
ABF
Image Enhancement
Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control, AGC, White Balance,
Privacy Masking, Sharpness, EIS, Pivot
Compression
H.264, H.264_High, MJPEG
Resolution
1920 x 1080 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)
Maximum Frame Rate
60 fps @ 1920 x 1080
Multi-Streaming
Up to 4
ROI (Region of Interest)
Smart codec (Up to 8)
Video Analytics
Motion detection, Tampering alarm, Face detection, Intrusion detection, Crossing line,
Object counting, Object removal, Object desertion
Text Overlay
Support
Audio Compression
G.711, G.726
2-way Audio
Support
Audio Detection
Support
Event Trigger
Video analytics, Audio detection, Alarm input
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Analog Out
RCA out
Audio In / Out
1 In / 1 Out
Alarm In / Out
1 In / 1 Out
RS-485
Support
SD Slot
micro SD (Up to 32 GB)
Ethernet
RJ-45 10 / 100 BASE-T
Security
Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Protocol
IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP, QoS,
UPnP port forwarding
IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
General
Integrated Software
LG Ipsolute VMS Suite / Mobile application (iPhone, iPad, Android)
Connections
Up to 20
Power Source
DC 12 V, PoE
Maximum Power
Consumption
6.9 W
Maximum Input Current
590 mA (DC 12 V), 150 mA (PoE)
Operation Temperature /
Humidity
-10 ºC to 55 ºC / 0 % RH to 80 % RH
Dimension (W x H x D)
69 mm x 54 mm x 136 mm
Weight
395 g
30Reference
Item
Camera
Video / Audio
Event
Interface
Network
LNB5110
Image Device
6.28 mm (1/3 Type) CMOS
Lens Type
CS mountable
Day / Night
ICR (Auto / Day / Night / External / Schedule)
Minimum Illumination
Color: 0.03 lx (F1.2, Gain : High, 1/30 sec, 50 IRE)
B/W: 0.002 lx (F1.2, Gain : High, 1/30 sec, 50 IRE)
WDR
Support
Image Enhancement
Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control, AGC, White Balance,
Privacy Masking, Sharpness, EIS, Pivot
Compression
H.264, H.264_High, MJPEG
Resolution
1280 x 1024 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)
Maximum Frame Rate
60 fps @ 1280 x 1024
Multi-Streaming
Up to 4
ROI (Region of Interest)
Smart codec (Up to 8)
Video Analytics
Motion detection, Tampering alarm, Face detection, Intrusion detection, Crossing line,
Object counting, Object removal, Object desertion
Text Overlay
Support
Audio Compression
G.711, G.726
2-way Audio
Support
Audio Detection
Support
Event Trigger
Video analytics, Audio detection, Alarm input
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Analog Out
RCA out
Audio In / Out
1 In / 1 Out
Alarm In / Out
1 In / 1 Out
RS-485
Support
SD Slot
micro SD (Up to 32 GB)
Ethernet
RJ-45 10 / 100 BASE-T
Security
Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Protocol
IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP, QoS,
UPnP port forwarding
IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
General
Integrated Software
LG Ipsolute VMS Suite / Mobile application (iPhone, iPad, Android)
Connections
Up to 20
Power Source
DC 12 V, PoE
Maximum Power
Consumption
5.9 W
Maximum Input Current
490 mA (DC 12 V), 130 mA (PoE)
Operation Temperature /
Humidity
-10 ºC to 55 ºC / 0 % RH to 80 % RH
Dimension (W x H x D)
69 mm x 54 mm x 122 mm
Weight
365 g
Reference31
Item
Camera
Video / Audio
Event
Interface
Network
LND5110
Image Device
6.28 mm (1/3 Type) CMOS
Lens Type
3 mm to 9 mm F1.2
Day / Night
ICR (Auto / Day / Night / External / Schedule)
Minimum Illumination
Color: 0.03 lx (F1.2, Gain : High, 1/30 sec)
B/W: 0.002 lx (F1.2, Gain : High, 1/30 sec)
WDR
Support
Image Enhancement
Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control, AGC, White Balance,
Privacy Masking, Sharpness, EIS, Pivot
Compression
H.264, H.264_High, MJPEG
Resolution
1280 x 1024 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)
Maximum Frame Rate
60 fps @ 1280 x 1024
Multi-Streaming
Up to 4
ROI (Region of Interest)
Smart codec (Up to 8)
Video Analytics
Motion detection, Tampering alarm, Face detection, Intrusion detection, Crossing line,
Object counting, Object removal, Object desertion
Text Overlay
Support
Audio Compression
G.711, G.726
2-way Audio
Support
Audio Detection
Support
Event Trigger
Video analytics, Audio detection, Alarm input
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Analog Out
BNC Out
Audio In / Out
1 In / 1 Out
Alarm In / Out
1 In / 1 Out
SD Slot
micro SD (Up to 32 GB)
Ethernet
RJ-45 10 / 100 BASE-T
Security
Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Protocol
IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP, QoS,
UPnP port forwarding
IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
General
Integrated Software
LG Ipsolute VMS Suite / Mobile App (iPhone, iPad, Android)
Connections
Up to 20
Power Source
DC 12 V, PoE
Maximum Power
Consumption
5.9 W
Maximum Input Current
490 mA (DC 12 V), 130 mA (PoE)
Operation Temperature /
Humidity
-10 ºC to 55 ºC / 0 % RH to 80 % RH
Dimension (Ø x H)
140 mm x 122 mm
Weight
530 g
32Reference
Item
Camera
Video / Audio
Event
Interface
Network
LNV5110R
LND5110R
Image Device
6.28 mm (1/3 Type) CMOS
Lens Type
3 mm to 9 mm F1.2
Day / Night
ICR (Auto / Day / Night / External / Schedule)
Minimum Illumination
Color: 0.03 lx @ F1.2 (1/30 sec, 50 IRE)
B/W: 0 lx @ IR LED on
WDR
Support
IR Distance
30 m
Image Enhancement
Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control, AGC, White Balance,
Privacy Masking, Sharpness, EIS, Pivot, Smart IR
Compression
H.264, H.264_High, MJPEG
Resolution
1280 x 1024 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)
Maximum Frame Rate
60 fps @ 1280 x 1024
Multi-Streaming
Up to 4
ROI (Region of Interest)
Smart codec (Up to 8)
Video Analytics
Motion detection, Tampering alarm, Face detection, Intrusion detection, Crossing line,
Object counting, Object removal, Object desertion
Text Overlay
Support
Audio Compression
G.711, G.726
2-way Audio
Support
Audio Detection
Support
Event Trigger
Video analytics, Audio detection, Alarm input
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Analog Out
BNC out
Audio In / Out
1 In / 1 Out
Alarm In / Out
1 In / 1 Out
SD Slot
micro SD (Up to 32 GB)
Ethernet
RJ-45 10 / 100 BASE-T
Security
Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Protocol
IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP, QoS,
UPnP port forwarding
IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
General
Integrated Software
LG Ipsolute VMS Suite / Mobile application (iPhone, iPad, Android)
Connections
Up to 20
Power Source
DC 12 V, PoE
Maximum Power
Consumption
8.2 W
Maximum Input Current
610 mA (DC 12 V), 170 mA (PoE)
Operation Temperature /
Humidity
-10 ºC to 55 ºC / 0 % RH to 80 % RH
Protection
IK10, IP66
Dimension (Ø x H)
140 mm x 122 mm
Weight
905 g
Not support
550 g
Reference33
Item
Camera
Video / Audio
Event
Interface
Network
LNU5110R
Image Device
6.28 mm (1/3 Type) CMOS
Lens Type
3 mm to 9 mm F1.2
Day / Night
ICR (Auto / Day / Night / External / Schedule)
Minimum Illumination
Color: 0.03 lx @ F1.2 (1/30 sec, 50 IRE)
B/W: 0 lx @ IR LED on
WDR
Support
IR Distance
40 m
Image Enhancement
Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control, AGC, White Balance,
Privacy Masking, Sharpness, EIS, Pivot, Smart IR
Compression
H.264, H.264_High, MJPEG
Resolution
1280 x 1024 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)
Maximum Frame Rate
60 fps @ 1280 x 1024
Multi-Streaming
Up to 4
ROI (Region of Interest)
Smart codec (Up to 8)
Video Analytics
Motion detection, Tampering alarm, Face detection, Intrusion detection, Crossing line,
Object counting, Object removal, Object desertion
Text Overlay
Support
Audio Compression
G.711, G.726
2-way Audio
Support
Audio Detection
Support
Event Trigger
Video analytics, Audio detection, Alarm input
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Analog Out
BNC out
Audio In / Out
1 In / 1 Out
Alarm In / Out
1 In / 1 Out
SD Slot
micro SD (Up to 32 GB)
Ethernet
RJ-45 10 / 100 BASE-T
Security
Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Protocol
IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP, QoS,
UPnP port forwarding
IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
General
Integrated Software
LG Ipsolute VMS Suite / Mobile application (iPhone, iPad, Android)
Connections
Up to 20
Power Source
AC 24 V, DC 12 V, PoE
Maximum Power
Consumption
10.6 W
Maximum Input Current
670 mA ( AC 24 V), 750 mA (DC 12 V), 200 mA (PoE)
Operation Temperature /
Humidity
-10 ºC to 55 ºC / 0 % RH to 80 % RH
Protection
IK10, IP66
Dimension (W x H x D)
92 mm x 90 mm x 339 mm
Weight
1.54 kg (with Sunshield 1.7 kg)
34Reference
Item
Camera
Video / Audio
Event
Interface
Network
LNV7210
LND7210
Image Device
6.4 mm (1/2.8 Type) CMOS
Lens Type
3 mm to 9 mm F1.2 (x3 Zoom)
Day / Night
ICR (Auto / Day / Night / External / Schedule)
Minimum Illumination
Color: 0.03 lx @ F1.2 (1/30 sec, 50 IRE)
B/W: 0.003 lx @ F1.2 (1/30 sec, 50 IRE)
WDR
Support
Image Enhancement
Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control, AGC, White Balance,
Privacy Masking, Sharpness, EIS, Pivot
Compression
H.264, H.264_High, MJPEG
Resolution
1920 x 1080 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)
Maximum Frame Rate
60 fps @ 1920 x 1080
Multi-Streaming
Up to 4
ROI (Region of Interest)
Smart codec (Up to 8)
Video Analytics
Motion detection, Tampering alarm, Face detection, Intrusion detection, Crossing line,
Object counting, Object removal, Object desertion
Text Overlay
Support
Audio Compression
G.711, G.726
2-way Audio
Support
Audio Detection
Support
Event Trigger
Video analytics, Audio detection, Alarm input
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Analog Out
BNC out
Audio In / Out
1 In / 1 Out
Alarm In / Out
1 In / 1 Out
SD Slot
micro SD (Up to 32 GB)
Ethernet
RJ-45 10 / 100 BASE-T
Security
Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Protocol
IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP, QoS,
UPnP port forwarding
IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
General
Integrated Software
LG Ipsolute VMS Suite / Mobile application (iPhone, iPad, Android)
Connections
Up to 20
Power Source
DC 12 V, PoE
Maximum Power
Consumption
8.7 W (DC 12 V), 10.4 W (PoE 48 V)
Maximum Input Current
730 mA (DC 12 V), 280 mA (PoE)
Operation Temperature /
Humidity
-10 ºC to 50 ºC / 0 % RH to 80 % RH
Protection
IK10, IP66
Dimension (Ø x H)
140 mm x 122 mm
Weight
950 g
Not support
613 g
Reference35
Item
Camera
Video / Audio
Event
Interface
Network
LNV7210R
Image Device
6.4 mm (1/2.8 Type) CMOS
Lens Type
3 mm to 9 mm F1.2 (x3 Zoom)
Day / Night
ICR (Auto / Day / Night / External / Schedule)
Minimum Illumination
LND7210R
Color: 0.03 lx @ F1.2 (1/30 sec, 50 IRE)
B/W: 0 lx @ IR LED on
WDR
Support
IR Distance
20 m
Image Enhancement
Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control, AGC, White Balance,
Privacy Masking, Sharpness, EIS, Pivot, Smart IR
Compression
H.264, H.264_High, MJPEG
Resolution
1920 x 1080 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)
Maximum Frame Rate
60 fps @ 1920 x 1080
Multi-Streaming
Up to 4
ROI (Region of Interest)
Smart codec (Up to 8)
Video Analytics
Motion detection, Tampering alarm, Face detection, Intrusion detection, Crossing line,
Object counting, Object removal, Object desertion
Text Overlay
Support
Audio Compression
G.711, G.726
2-way Audio
Support
Audio Detection
Support
Event Trigger
Video analytics, Audio detection, Alarm input
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Analog Out
BNC out
Audio In / Out
1 In / 1 Out
Alarm In / Out
1 In / 1 Out
SD Slot
micro SD (Up to 32 GB)
Ethernet
RJ-45 10 / 100 BASE-T
Security
Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Protocol
IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP, QoS,
UPnP port forwarding
IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
General
Integrated Software
LG Ipsolute VMS Suite / Mobile application (iPhone, iPad, Android)
Connections
Up to 20
Power Source
DC 12 V, PoE
Maximum Power
Consumption
8.7 W (DC 12 V), 10.4 W (PoE 48 V)
Maximum Input Current
730 mA (DC 12 V), 280 mA (PoE)
Operation Temperature /
Humidity
-10 ºC to 50 ºC / 0 % RH to 80 % RH
Protection
IK10, IP66
Dimension (Ø x H)
140 mm x 122 mm
Weight
957 g
Not support
620 g
36Reference
Item
Camera
Video / Audio
Event
Interface
Network
LNU7210R
Image Device
6.4 mm (1/2.8 Type) CMOS
Lens Type
3 mm to 9 mm F1.2 (x3 Zoom)
Day / Night
ICR (Auto / Day / Night / External / Schedule)
Minimum Illumination
Color: 0.03 lx @ F1.2 (1/30 sec, 50 IRE)
B/W: 0 lx @ IR LED on
WDR
Support
IR Distance
30 m
Image Enhancement
Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control, AGC, White Balance,
Privacy Masking, Sharpness, EIS, Pivot, Smart IR
Compression
H.264, H.264_High, MJPEG
Resolution
1920 x 1080 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)
Maximum Frame Rate
60 fps @ 1920 x 1080
Multi-Streaming
Up to 4
ROI (Region of Interest)
Smart codec (Up to 8)
Video Analytics
Motion detection, Tampering alarm, Face detection, Intrusion detection, Crossing line,
Object counting, Object removal, Object desertion
Text Overlay
Support
Audio Compression
G.711, G.726
2-way Audio
Support
Audio Detection
Support
Event Trigger
Video analytics, Audio detection, Alarm input
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Analog Out
BNC out
Audio In / Out
1 In / 1 Out
Alarm In / Out
1 In / 1 Out
SD Slot
micro SD (Up to 32 GB)
Ethernet
RJ-45 10 / 100 BASE-T
Security
Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Protocol
IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP, QoS,
UPnP port forwarding
IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
General
Integrated Software
LG Ipsolute VMS Suite / Mobile application (iPhone, iPad, Android)
Connections
Up to 20
Power Source
AC 24 V, DC 12 V, PoE
Maximum Power
Consumption
10.6 W (AC 24 V), 9.1 W (DC 12 V), 9.6 W (PoE)
Maximum Input Current
670 mA (AC 24 V), 750 mA (DC 12 V), 200 mA (PoE)
Operation Temperature /
Humidity
-10 ºC to 50 ºC / 0 % RH to 80 % RH
Protection
IK10, IP66
Dimension (W x H x D)
92.1 mm x 89.8 mm x 338.6 mm
Weight
1.54 kg (with Sunshield 1.7 kg)
Reference37
Item
Camera
Video / Audio
Event
Interface
Network
LNV7210RH
Image Device
6.4 mm (1/2.8 Type) CMOS
Lens Type
3 mm to 9 mm F1.2 (x3 Zoom)
Day / Night
ICR (Auto / Day / Night / External / Schedule)
Minimum Illumination
Color: 0.03 lx @ F1.2 (1/30 sec, 50 IRE)
B/W: 0 lx @ IR LED on
WDR
Support
IR Distance
20 m
Image Enhancement
Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control, AGC, White Balance,
Privacy Masking, Sharpness, EIS, Pivot, Smart IR
Compression
H.264, H.264_High, MJPEG
Resolution
1920 x 1080 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)
Maximum Frame Rate
60 fps @ 1920 x 1080
Multi-Streaming
Up to 4
ROI (Region of Interest)
Smart codec (Up to 8)
Video Analytics
Motion detection, Tampering alarm, Face detection, Intrusion detection, Crossing line,
Object counting, Object removal, Object desertion
Text Overlay
Support
Audio Compression
G.711, G.726
2-way Audio
Support
Audio Detection
Support
Event Trigger
Video analytics, Audio detection, Alarm input
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Analog Out
BNC out
Audio In / Out
1 In / 1 Out
Alarm In / Out
1 In / 1 Out
SD Slot
micro SD (Up to 32 GB)
Ethernet
RJ-45 10 / 100 BASE-T
Security
Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Protocol
IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP, QoS,
UPnP port forwarding
IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
General
Integrated Software
LG Ipsolute VMS Suite / Mobile application (iPhone, iPad, Android)
Connections
Up to 20
Power Source
DC 12 V, PoE
Maximum Power
Consumption
11.4 W (DC 12 V), 12.8 W (PoE)
Maximum Input Current
940 mA (DC 12 V), 340 mA (PoE)
Operation Temperature /
Humidity
-40 ºC to 50 ºC / 0 % RH to 80 % RH
Storage Temperature /
Humidity
-30 ºC to 60 ºC / 0 % RH to 80 % RH
Protection
IK10, IP66
Dimension (Ø x H)
140 mm x 122 mm
Weight
957 g
38Reference
Item
Camera
Video / Audio
Event
Interface
Network
LNU7210RH
Image Device
6.4 mm (1/2.8 Type) CMOS
Lens Type
3 mm to 9 mm F1.2 (x3 Zoom)
Day / Night
ICR (Auto / Day / Night / External / Schedule)
Minimum Illumination
Color: 0.03 lx @ F1.2 (1/30 sec, 50 IRE)
B/W: 0 lx @ IR LED on
WDR
Support
IR Distance
30 m
Image Enhancement
Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control, AGC, White Balance,
Privacy Masking, Sharpness, EIS, Pivot, Smart IR
Compression
H.264, H.264_High, MJPEG
Resolution
1920 x 1080 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)
Maximum Frame Rate
60 fps @ 1920 x 1080
Multi-Streaming
Up to 4
ROI (Region of Interest)
Smart codec (Up to 8)
Video Analytics
Motion detection, Tampering alarm, Face detection, Intrusion detection, Crossing line,
Object counting, Object removal, Object desertion
Text Overlay
Support
Audio Compression
G.711, G.726
2-way Audio
Support
Audio Detection
Support
Event Trigger
Video analytics, Audio detection, Alarm input
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Analog Out
BNC out
Audio In / Out
1 In / 1 Out
Alarm In / Out
1 In / 1 Out
SD Slot
micro SD (Up to 32 GB)
Ethernet
RJ-45 10 / 100 BASE-T
Security
Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Protocol
IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP, QoS,
UPnP port forwarding
IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
General
Integrated Software
LG Ipsolute VMS Suite / Mobile application (iPhone, iPad, Android)
Connections
Up to 20
Power Source
AC 24 V, DC 12 V, PoE
Maximum Power
Consumption
13.5 W (AC 24 V), 11.4 W (DC 12 V), 12.8 W (PoE)
Maximum Input Current
1 100 mA (AC 24 V), 940 mA (DC 12 V), 340 mA (PoE)
Operation Temperature /
Humidity
-40 ºC to 50 ºC / 0 % RH to 80 % RH
Storage Temperature /
Humidity
-30 ºC to 60 ºC / 0 % RH to 80 % RH
Protection
IK10, IP66
Dimension (W x H x D)
92.1 mm x 89.8 mm x 338.6 mm
Weight
1.54 kg (with Sunshield 1.7 kg)
Reference39
Download PDF

advertising