LG | LNU7210RH | User guide | LG LNU7210RH Owner's manual

LG LNU7210RH Owner's manual
Specification
Item
Camera
OWNER’S MANUAL
Network
Camera
LNU7210RH
Image Device
6.4 mm (1/2.8 Type) CMOS
Lens Type
3 mm to 9 mm F1.2 (x3 Zoom)
Day / Night
ICR (Auto / Day / Night / External / Schedule)
Minimum
Illumination
Color: 0.03 lx @ F1.2 (1/30 sec, 50 IRE)
WDR
Support
IR Distance
30 m
Image
Enhancement
Backlight Compensation, 2D+3D-DNR, De-fog, Exposure
Control, AGC, White Balance, Privacy Masking, Sharpness, EIS,
Pivot, Smart IR
Compression
H.264, H.264_High, MJPEG
Resolution
1920 x 1080 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)
Maximum
Frame Rate
60 fps @ 1920 x 1080
Network
Support (Up to 8)
Video Analytics
Motion detection, Tampering alarm, Face detection, Intrusion
detection, Crossing line, Object counting, Object removal,
Object desertion
MODEL
LNU7210RH
Event
*MFL69355833*
Interface
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
Warning: Do not install this equipment in a
confined space such as a bookcase or similar
unit.
Warning: Wiring methods shall be in
accordance with the National Electric Code,
ANSI/NFPA 70.
Warning: This is a class A product. In a
domestic environment this product may cause
radio interference in which case the user may
be required to take adequate measures.
Warning: To reduce a risk of fire or electric
shock, do not expose this product to rain or
moisture.
Warning: Please adopt the power adapter
which can meet the safety extra low voltage
(SELV) standard. And source with DC 12 V or
AC 24 V (depending on models) according
to the IEC60950-1 and Limited Power Source
standard.
Warning: Install the camera on a ceiling or
wall where can withstand the weight of 5 times
of the camera including mounting bracket.
Caution: This installation shall be made by a
qualified service person and shall conform to
all local codes.
Caution: To avoid electrical shock, do not
open the cabinet. Refer servicing to qualified
personnel only.
Caution: The apparatus shall not be exposed
to water (dripping or splashing) and no objects
filled with liquids, such as vases, shall be placed
on the apparatus.
Caution: Make sure the power supply voltage
is correct before using the camera.
Caution: Do not drop the camera or subject it
to physical shock.
Caution: The sensor may be burned out by
a laser beam, so when any laser equipment is
being used, make sure that the surface of the
sensor not be exposed to the laser beam.
Caution: While shipping, the camera should
be packed in its original packing.
Support
Audio
Compression
G.711, G.726
2-way Audio
Support
Audio Detection Support
Please read this manual carefully before operating
your set and retain it for future reference.
Security
Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Protocol
IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP,
QoS, UPnP port forwarding
Integrated
Software
LG Ipsolute VMS Suite / Mobile application (iPhone, iPad,
Android)
Connections
Up to 20
Power Source
AC 24 V, DC 12 V, PoE
Maximum
Power
Consumption
13.5 W (AC 24 V), 11.4 W (DC 12 V), 12.8 W (PoE)
IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
Maximum Input
1 100 mA (AC 24 V), 940 mA (DC 12 V), 340 mA (PoE)
Current
General
ROI (SmartCodec)
Text Overlay
RJ-45 10 / 100 BASE-T
B/W: 0 lx @ IR LED on
Multi-Streaming Up to 4
Video /
Audio
Ethernet
Event Trigger
Video analytics, Audio detection, Alarm input
Event
Notification
Relay Out, Email, FTP
Pre Event
Buffering
Support
Analog Out
BNC out
Audio In / Out
1/1
Alarm In / Out
1 In / 1 Out
SD Slot
micro SD (Up to 32 GB)
Note:
Please make sure the product is installed
appropriate places where secured from flood,
such as under the eaves, to operate properly.
This product is certified as IP66 standard.
However, if there is any flood concerns, it
is highly recommended to use an outdoor
Housing. When you install the camera inside
an outdoor Housing, please use one of the
following methods:
1. Remove the front glass of Housing before
installing the camera.
2. To keep the front glass of Housing, remove
the front cover, and then put the camera
close to the front glass.
Disposal of your old appliance
1.
3.
-40 ºC to 50 ºC / 0 % RH to 80 % RH
Storage
Temperature /
Humidity
-30 ºC to 60 ºC / 0 % RH to 80 % RH
Protection
IK10, IP66
Dimension (W x
H x D)
92.1 mm x 89.8 mm x 338.6 mm
Weight
1.54 kg (with Sunshield 1.7 kg)
Символ Кедендік одақтың
005/2011 техникалық
регламентіне сәйкес
қолданылады және осы
өнімнің қаптамасын екінші рет
пайдалануға арналмағанын
және жоюға жататынын
көрсетеді. Осы өнімнің
қаптамасын азық-түлік өнімдерін
сақтау үшін пайдалануға тыйым
салынады.
Символ «петля Мебиуса»
указывает на возможность
утилизации упаковки.
Символ может быть дополнен
обозначением материала
упаковки в виде цифрового и/или
буквенного обозначения.
Символ қаптаманы жою
мүмкіндігін көрсетеді. Символ
сандық код және/немесе әріп
белгілері түріндегі қаптама
материалының белгісімен
толықтырылуы мүмкін.
Российская Федерация
Импортер ООО “ЛГ Электроникс Рус”
Адрес импортера: 143160 Российская Федерация, Московская область, Рузский район, сельское
поселение Дороховское, 86 км. Минского шоссе, д.9
Адрес производителя: ЛГ ЭЛЕКТРОНИКС (ХУЖОУ) ИНК., ЗАВОД ХАТАИ
Г Электроникс (Хужоу) Инк., завод Хатаи
Л
516006, Китай, пров. ГуанДонг, г. Хужоу, Промышленная зона
Жонгкай, Индустриальный парк Хутаи, ХуФенг Донг Уи Роуд, 13.
Сделано в Китае
Note that design and specification of this unit may change from the manual as quality and
improvement without prior notice.
Components
Camera, CD (Software and Owner’s Manual), Installation Manual, Test monitor cable, Wrench,
Screws (3 EA), Installation sticker, Sunshield and Fixing screw
Contact office for compliance of this product:
LG Electronics European Shared Service Center B.V.
European Standard Team
Krijgsman 1
1186 DM Amstelveen
The Netherlands
2.
Operation
Temperature /
Humidity
Символ «не для пищевой
продукции» применяется в
соответствие с техническим
регламентом Таможенного
союза «О безопасности
упаковки» 005/2011 и указывает
на то, что упаковка данного
продукта не предназначена для
повторного использования и
подлежит утилизации. Упаковку
данного продукта запрещается
использовать для хранения
пищевой продукции.
This crossed-out
wheeled bin symbol
indicates that waste
electrical and electronic
products (WEEE)
should be disposed
of separately from the
municipal waste stream.
Old electrical products can contain
hazardous substances so correct disposal
of your old appliance will help prevent
potential negative consequences for the
environment and human health. Your old
appliance may contain reusable parts that
could be used to repair other products,
and other valuable materials that can be
recycled to conserve limited resources.
You can take your appliance either to the
shop where you purchased the product,
or contact your local government waste
office for details of your nearest authorised
WEEE collection point. For the most up to
date information for your country please
see www.lg.com/global/recycling
Handling of the unit
Be careful not to spill water or other liquids on
the unit. Be cautious not to get combustible or
metallic material inside the body. If used with
foreign matter inside, the camera is liable to fail
or to get cause of fire or electric shock.
•
Remove dust or dirt on the surface of the
lens with a blower.
•
Use a soft and lint-free, dry cloth(such as
glass cleaner) to clean the body. If it is
very dirty, use a cloth dampened with a
small quantity of neutral detergent then
wipe dry.
•
Avoid the use of volatile solvents such
as thinners, alcohol, benzene and
insecticides.
They may damage the surface finish and/
or impair the operation of the camera.
•
This camera is designed for mounting on
the ceiling or wall. If you install this camera
upside down, it may cause malfunction.
Operating and storage
location
Avoid viewing a very bright object (such as
light fittings) during an extended period. Avoid
operating or storing the unit in the following
locations.
•
Extremely hot or cold places (operating
temperature -40 °C to 50 °C, however, we
recommend that the unit be used within a
temperature range of -30 °C to 45 °C)
•
Damp or dust place
•
Places exposed to rain
•
Places subject to strong vibration
•
Close to generators of powerful
electromagnetic radiation such as radio or
TV transmitters.
•
Do not use the camera in such place
where rapid temperature fluctuation by
switching an air conditioner on and off.
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in
this product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices
are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the
cost of performing such distribution (such as the cost of media, shipping and handling) upon email
request to opensource@lge.com. This offer is valid for three (3) years from the date on which you
purchased the product.
Part Names and Functions
a
i
cd
b
j
Connection
k
e
l m
f
g h
n
a Lens Cover
b Angle adjuster
Adjust the camera angle.
c Tilt adjuster
Adjust the tilt position.
d Pan adjuster
Adjust the pan position.
e Power input terminal
Connects to DC 12 V or AC 24 V power supply using proper cables. This camera must always
be operated DC 12 V or AC 24 V. Certified/Listed Adaptor which comply with LPS.
f AUDIO IN / OUT (Line Level Input / Output)
g ALARM IN & OUT / ALARM IN & OUT RETURN
Provides physical interface for sensor and Alarm/Relay.
h ETHERNET / PoE Port
Connects to a PC or a network via a hub with a 10 BASE-T / 100 BASE-TX cable attached RJ-45
connector.
NOTE:
Power over Ethernet (PoE) is a technology that integrates power into a standard LAN
infrastructure. It enables power to be provided to the network device, such as a network
camera, using the same cable as that used for network connection. It eliminates the need for
power outlets at the device locations and enables easier application of uninterruptible power
supplies (LPS).
i IR LED
NOTE:
Do not stare at operating IR LED within hazard distances (1 m).
j IR Sensor
k RESET button
Push the button more than 3 seconds, this would restore the factory default network related
settings.
l Video Out Connector
Use this jack for checking the picture with portable monitor when install the camera.
m Jog button
Use this button for control the Zoom / Focus of the camera.
n micro SD card slot
Insert the micro SD card.
Precautions
Connecting Power Source
Connecting Alarm Device
•
Connect power, using one of the methods
listed below:
Alarm terminals are used to connect the alarm
(relay) devices such as sensors, door switches,
etc.
Be sure to switch off the unit before
installation and connection.
The installation should be made by
qualified service personnel or system
installers.
Do not expose the power and connection
cables to moisture, which may cause
damage to the unit.
•
•
To use the power adapter
Connect DC 12 V or AC 24 V power source to
the power input terminal as shown below.
(recommended power adapter is DC 12 V or
AC 24 V / 1.5 A or above)
Connecting Microphone and
Speaker Device
Optionally connect an active speaker and/or
external microphone with a built-in amplifier.
ALARM IN & OUT / ALARM IN & OUT RETURN (Sensor Input/ Relay Output)
Connect the sensor device and alarm (relay)
device to the alarm terminal. Alarm signal is
outputted at an event occurrence.
AUDIO OUT
AUDIO IN
Connecting Network
You can control and monitor the system via
network. With the remote control (monitoring),
you can change the system configuration
or monitor the image via network. After the
installation, check the network settings for the
remote control and monitoring work.
Connect the IP camera to your network using a
standard RJ-45 network cable as shown below.
Alarm (relay)
Device
To use the PoE (Power over Ethernet) device
Sensor Device
Connect the PoE cable to the LAN port on the
unit. You must use the “IEEE802.3af” standard
PoE device.
ETHERNET
With PoE
ETHERNET
With PoE
ETHERNET
With PoE
PoE Device
(IEEE802.3af )
NOTE:
•
When the connecting Network, Power
and Alarm, tighten the screws as shown
above.
•
Keep the microphone away from the
speaker to avoid howling.
Connecting Portable Monitor
Connect the portable monitor to the video
jack using the test monitor cable.
Broadband
Service
Router
PoE Device
(IEEE802.3af )
Broadband
Service
NOTE:
The Photo MOS Relay is rated for 100 mA at
DC 20 V or 100 mA at AC 28 V.
NOTE:
If the camera doesn’t work properly after
connecting PoE device, please check if the PoE
device supplies enough power.
Installation
Using the micro SD card
You can record your surveillance environment with
the micro SD card even if the network is disconnected
condition.
To insert the micro SD card
1.
Open the Cover on the main body by loosening
the screw.
•
•
•
•
2.
If you insert the micro SD card in the wrong
position, the micro SD card may be damaged
or it may cause the malfunction of the micro SD
Card Slot.
Keep the terminal part of the micro SD card in
clean. Be careful the terminal part of the micro SD
card not to dusty.
As the micro SD card is consumable, the micro
SD card end its days and may be not able to save
data if you use it more than over certain times.
In this case, replace micro SD card to buy a new
one.
Close the cover and fasten the screw securely
using a screwdriver as shown below.
Insert the micro SD card carefully as shown in the
following illustrations. Make sure the micro SD
card terminal position before insert the micro SD
card. Push the back end of the micro SD card to
fix it at the last step.
2.
Take the micro SD card out carefully from the
camera. It may cause a malfunction of the micro
SD card or the micro SD card slot if you use the
power too much at lock status.
CAUTION:
•
If you install the micro SD card on the camera
and remove with the micro SD card condition
indicator lights on, you must unmount the micro
SD card by using the [System > Storage > Device
Management > Unmount] menu. The micro SD
card data is compromised or the camera may not
operate normally, if you remove the card without
use [Unmount] function.
•
LG Electronics is not responsible for deleted data
caused by user mishandling when you insert or
remove the micro SD card.
Recommended the micro SD card specification
Maker
LG
Sandisk
Remove the micro SD card
1.
NOTES:
•
Do not use the power too much when you insert
the micro SD card. The micro SD card may be
damaged.
Press the back end of the micro SD card to
release the lock condition.
Transcend
Capacity
Block Size
(FAT 32)
Less than
32 GB
32 kbyte
NOTE:
Follow the instructions below to ceiling or wall mount
the camera.
3.
Install the camera by using M4 Tapping screws to
fix it on the ceiling.
Mounting the Camera
1.
2.
Adjust the camera position
Assemble the Sunshield
You should adjust the camera angle position as shown
below illustration. Adjust the camera angle position by
following step a and b.
Adjust the position of the Sunshield, then assemble
the Sunshield.
Using a template as a guide, make a hole through
the ceiling.
1.
Adjust the Pan.
Connect the cables to the cable jacks of the
camera body.
2.
Adjust the Tilt.
3.
Adjust the Angle.
Connecting Waterproof processing
of cable
Surely use the Butyl tape.
1.
Connect the cables.
2.
Bind the cables together with Butyl tape.
Speed of reading and writing more than 10 MB/Sec.
(Class 6)
WARNING:
•
The cables are not waterproofed completely. So
seal the tube ends and the portions between
cable cores as well as connecting portions with
Butyl tape.
•
If not using the Butyl tape, it may cause water
absorption from a gap and finally condensation
and water leakage.
NOTE:
•
The camera could be damaged by adjusting Pan,
Tilt by force.
•
Camera can be damaged if you adjust the Pan
/ Tilt / Angle when the screw is fixed.
•
Be careful not to rotate the Pan and Angle more
than 360°, it may damage the internal cable.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising