LG | LPT-EI553PS | LG LPT-EI553PS Owner’s Manual

LPT-EP500_ENG
11/4/15
9:43 AM
Page 1
Dome Camera
Owner’s Manual
MODEL: LPT-EP551PS / LPT-EP553PS
LPT-EI551PS / LPT-EI553PS
Before installing and using the camera, please read this owner's
manual carefully and retain for future reference.
LPT-EP500_ENG
11/4/15
9:43 AM
Page 2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
FCC WARNING : This equipment may generate or
use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly
approved in the instruction manual. The user could
lose the authority to operate this equipment if an
unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case
the user will be required to correct the interference
at his own expense.
• A suitable conduit entries, knock-outs or glands
shall be provided in the cable entries of this product in the end user.
2
•
Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer ’s instructions.
• Holes in metal,,through which insulated wires
pass,shall have smooth well rounded surfaces or
shall be provided with brushings.
Warning: Do not install this equipment in a confined
space such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance
with the National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic
environment this product may cause radio interference in which case the user may be required to take
adequate measures.
Warning: To reduce a risk of fire or electric shock, do
not expose this product to rain or moisture.
Caution: This installation should be made by a qualified service person and should conform to all local
codes.
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, should be placed on the
apparatus.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is
attached to a product it means the product is
covered by the European Directive
2002/96/EC.
2. All electrical and electronic products should be
disposed of separately from the municipal
waste stream via designated collection facilities appointed by the government or the local
authorities.
3. The correct disposal of your old appliance will
help prevent potential negative consequences
for the environment and human health.
4. For more detailed information about disposal
of your old appliance, please contact your city
office, waste disposal service or the shop
where you purchased the product.
This product is manufactured to comply
with the EEC DIRECTIVE 2004/108/EC
and 2006/95/EC.
LPT-EP500_ENG
11/4/15
9:43 AM
Page 3
Introduction
Contents
About Dome Camera
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
The dome cameras are designed for installation in an
indoor or outdoor video surveillance system.
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
About Dome Camera . . . . . . . . . . . . . . . . . . . . . . .3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . .5
Identification of Camera . . . . . . . . . . . . . . . . . . . . .6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-12
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Mounting the Camera . . . . . . . . . . . . . . . . . . . . .7-8
• Removing the Sponge . . . . . . . . . . . . . . . . . . .7
• Ceiling mount . . . . . . . . . . . . . . . . . . . . . . . . .7
• Pendant mount . . . . . . . . . . . . . . . . . . . . . . . .8
• Wall mount . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Setting the Switch . . . . . . . . . . . . . . . . . . . . . . .9-12
• RS-485 Parameter Setup . . . . . . . . . . . . . . . . .9
• Alarm Output Mode Setting . . . . . . . . . . . . . .10
• Camera ID Setting . . . . . . . . . . . . . . . . . .10-12
Connections . . . . . . . . . . . . . . . . . . . . . . . . .13-18
Precautions . . . . . . . . . . .
RS-485 Connection . . . . .
ALARM IN Connections . .
ALARM OUT Connections
Data Port Connections . . .
System Connection . . . . .
Adapter Connections . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
The camera incorporates the digital signal processor,
pan/tilt mechanism, x27 zoom lens and RS-485 communication interface in a compact outdoor enclosure.
A newly developed 1/4" CCD makes the camera
suitable for use under extremely low illumination conditions as well as in daylight.
Setup menus allow the camera to perform surveillance tasks by such means as motion detection, digital flip, pattern-recording and privacy zones.
Features
x
High Sensitivity Support
The camera provides the high quality picture with
1/4" Super HAD CCD.
x
Preset Position
Preset position is the function to register camera
monitoring positions (preset positions) associated
with position numbers. By entering the position
numbers, you can move cameras to the preset
positions.
A maximum of 128 Preset Position is available.
The moving speed and holding time are
adjustable.
x
Preset Tour
You can tour all preset positions that has already
been registered.
x
Preset Group Tour
You can create a preset group using the preset
positions that has already been registered (maximum 9 groups) and you can tour the preset position within the group.
A preset group should have a maximum of 8 preset positions.
.13
.13
.14
.15
.16
.17
.18
Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . .19-31
Setup Menu Overview . . . . . . . . . . . . . . . . . . . . .19
Setting Camera Menu . . . . . . . . . . . . . . . . . . . . .20
Camera Identification Setting . . . . . . . . . . . . . . . .21
Focus Settings . . . . . . . . . . . . . . . . . . . . . . . .21-22
White Balance Control Settings . . . . . . . . . . . . . .23
Exposure Settings . . . . . . . . . . . . . . . . . . . . .24-26
Auto Exposure Level Settings . . . . . . . . . . . . . . .27
Special Settings . . . . . . . . . . . . . . . . . . . . . . .28-29
Motion Detection Setting . . . . . . . . . . . . . . . . . . .30
Function On-Screen Display Setting . . . . . . . . . . .30
Privacy Masking Settings . . . . . . . . . . . . . . . . . . .31
Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .32
3
LPT-EP500_ENG
x
x
x
9:43 AM
Page 4
Pattern Function
A routine of manual operations can be stored for 8
minutes at the maximum and reproduced repetitively. The Panning, Tilting and Zoom controls are
available for recording the pattern.
Note: The available total time of pattern differs
depending on camera’s operation. When the time
is over, the pattern setup will automatically stop.
Privacy Mask
Privacy zone feature enables users to veil unwanted zones. This setting is used for masking
unwanted zones, hiding them from display on the
monitor screen. Up to 8 zones can be registered.
Auto Pan
The camera has an Auto Pan function that
enables to keep surveillance on every detail occurring around the specific area, which is preset to
watch in advance.
The camera can pan among the maximum 8
points you will set. The moving speed and holding
time are adjustable.
x
Auto Flip
When the camera is operated to tilt through the
90°, it can be watched the opposite side of the
locations by Auto Flip of a 180° horizontally.
x
Sophisticated Design
This is the surveillance camera that can fit any
indoor surroundings because it comes in the compact size and sophisticated design.
x
x
4
11/4/15
x
Alarm In function (8 channels)
Alarm input signals are supplied from external
devices through the ALARM IN connector to turn
the camera to a preset position.
x
Alarm Out function (4 channels)
When alarm inputs are supplied via the alarm
input connector on the camera, the camera sends
output signals via the alarm output connector on
the camera.
x
Controls by General Controller
This camera can be controlled by RS-485.
Especially the camera has an excellent cost-saving effect because it can be controlled by the general RX point of contact signal.
x
Connects with the maximum 256 cameras
This camera can be utilized after being connected
with maximum 256 cameras.
Therefore, it is capable of performing an excellent
job in the large buildings or department stores.
x
Day & Night Function
This camera can be selected Color or Black &
White. You can set Color in the daytime and Black
& White at night due to the low illumination. (Filter
Conversion type)
x
DSS (Digital Slow Shutter) function
It is possible to highly sensitive surveillance
because of DSS(Digital Slow Shutter) function.
x
WDR (Wide Dynamic Range) function
The camera can be best condition to watch easily
inside or outside in the strong back light.
Zoom Lens & Auto Focus
Zooming is possible from 27 times (the optical
zoom limit), to a maximum of X2 times digital
zoom.
Sensor Linkage
The camera is capable of capturing a subject by
the focus of camera moving promptly toward the
subject at the rate of 240°/sec when the camera
works with a detector (magnetic, beam, infrared
rays), and a subject moving within a detection
area is captured by a detector.
Note: During Auto Pan, Preset Tour, or Pattern
Record/Play, you can use only STOP key or
Joystick on the controller.
x
Power Supply
This camera must always be operated a AC 24V
Certified/Listed, class 2 power supply only.
x
Heat Pad
The heat pad is installed in this unit. If the unit’s
inside temperature is below than -1°C, the heat
pad is operated to rise the temperature.
LPT-EP500_ENG
11/4/15
9:43 AM
Page 5
Safety Precautions
x
Do not attempt to disassemble the camera
To prevent electric shock,do not remove screws or
covers. There are no user serviceable parts inside.
Ask a qualified service personnel for servicing.
x
Avoid the camera with direct sunlight
Do not aim the camera at bright objects.Whether
the camera is in use or not, never face it with
direct sunlight or other extremely bright objects.
Otherwise blooming or smear may be caused.
x
Handle the camera with care
Do not abuse the camera. Avoid striking, shaking,
etc. The camera could be damaged by improper
handling or storage.
x
Do not use strong solvents or detergents
Use a dry cloth to the camera when it is dirty. If it
is hard to remove the dirt on the camera, use a
mild detergent and wipe it gently.
x
Do not install this camera upside down
This camera is designed for mounting on the ceiling or wall.If you install this camera upside down,
for example, mounted on the floor, it may cause
malfunction.
x
Do not use the camera in such places as
shown below.
The lens may become cloudy due to condensation
if the camera is used under the following conditions.
- Rapid temperature fluctuation by switching an
air conditioner on and off.
- Rapid temperature fluctuation due to frequent
door opening and closing.
- Use in an environment where eyeglasses
become foggy.
- Use in a room filled with cigarette smoke or
dust.
If the lens becomes cloudy due to condensation,
remove the dome cover and wipe all moist surfaces with a soft cloth.
x
Before operating, please check proper temperature, humidity and power source ratings.
Use the camera under conditions where temperature is between -10 °C – +50 °C and humidity is
below 80%.
The input power source is AC 24V.
x
Consumables
Parts having contacts such as the lens-drive
motors,cooling fan built inside the camera are subject to wear with time. About replacement and
maintenance of such parts,please ask the nearest
service center.
5
LPT-EP500_ENG
11/4/15
9:43 AM
Page 6
Identification of Camera
e
a
f
g
h
b
i
c
d
a Camera mounting bracket
The bracket is optional for surface installation.
b Fall Prevention Wire
Be sure to hook the fall prevention wire into an bracket.
Caution: When you fix the the dome cover to the dome camera body, you must insert the wire in the dome
camera body. If not, the wire may obstruct the camera’s moving.
c Dome camera body
d Dome cover
e Power cable (AC 24V)
f Video output cable with BNC connector
Connects with the video connector of the monitor.
g Data Communication Port (RJ45) - RS-485 and Alarm Input
h Data Communication Port (RJ45) - RS-485 and Alarm Input
i Data Communication Port (RJ45) - Alarm Output
6
LPT-EP500_ENG
11/4/15
9:43 AM
Page 7
Installation
Precautions
Removing the Sponge
• The following steps of installation and connection
work should be done by qualified service personnel or system installers and should conform to all
local codes.
Before mounting the camera, remove the sponge for
camera protection.
Caution: Remove the sponge carefully without
remainder of the sponge in the camera.
• Be sure to switch the camera off before installation
and connection.
• Do not install the camera near the air outlet of an
air conditioner.
• Do not touch the dome cover’s window.
Mounting the Camera
The figures show an example of the camera mounted
on a ceiling or wall with a locally procured bracket.
Refer to the instructions included with the bracket for
filling gaps and holes with waterproof material.
Note: The camera have not been evaluated for wall
or ceiling mounting.
Sponge
Ceiling mount
The Ceiling
(LPT-EI551PS / LPT-EI553PS)
The Ceiling
7
LPT-EP500_ENG
11/4/15
9:43 AM
Page 8
Pendant mount
(LPTEP551PS / LPT-EP553PS)
a
Wall mount
b
(LPT-EP551PS / LPT-EP553PS)
c
■ How to install
“A” Pipe threads should be clean and
rust free. Use a sealer (such as
Teflon™ tape or silicone sealer) on
the threads.
Add thread
sealing tape
Note: The pipes and brackets for
mounting are not supplied.
Reference: Specifications of LG Standard pipe.
8
LPT-EP500_ENG
11/4/15
9:43 AM
Page 9
Setting the Switch
The DIP switch of the camera is one 8-bit switches
and employs RS-485 communication mode as basic
use. Switch settings are read into the camera when
the power is turned on. Make sure to turn it off, then
turn it back after changing the switch settings.
RS-485 Parameter Setup
The selected protocol,communication parameters,
and set unit numbers are read into the camera when
power is switched on.
1. Turn off the camera.
2. Remove the dome cover from the camera.
3. Separate the dome camera body from camera
mounting bracket.
4. Set the DIP switch on the bottom part of the camera according to the function shown in the table of
the below.
5. Turn on the camera. Setup is completed.
Switch position (5~8)
ON
1
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
ON
1
ON
1
ON
1
ON
ON
OFF
1
2
3
4
5
6
7
8
SW2 on main board
Function Effect
When the camera is connected to the controller with LG Multix protocol.
The controller with LG Multix protocol allow all control for this camera.
When the camera is connected to the controller with LG protocol.
The controller with LG protocol allow only limited control for this camera.
When the camera is connected to the controller with Pelco P protocol.
The controller with Pelco P protocol allow only limited control for this camera.
When the camera is connected to the controller with Pelco D protocol.
The controller with Pelco D protocol allow only limited control for this camera.
Note: If you are not using the controller with LG protocol, there may be some limitation of function control.
Switch position (1~4)
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
Function Effect
Switch position (1~4)
2
3
4
5
6
7
8
Baud Rate 9,600 BPS
communication speed
Baud Rate 1,200 BPS
communication speed
Baud Rate 2,400 BPS
communication speed
1
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
2
3
4
5
6
7
8
ON
1
ON
1
ON
ON
1
Function Effect
ON
ON
2
3
4
5
6
7
8
Baud Rate 4,800 BPS
communication speed
1
Baud Rate 19,200 BPS
communication speed
Baud Rate 38,400 BPS
communication speed
Baud Rate 57,600 BPS
communication speed
Baud Rate 115,200 BPS
communication speed
9
LPT-EP500_ENG
11/4/15
9:43 AM
Page 10
Alarm Output Mode Setting
The table for the camera ID setting
You can set the Alarm Output to the normal open or
normal close mode.
ID
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
ON
ON
OFF
1
2
3
4
5
6
7
8
SW1 on IF board
Alarm
Output
Number
Switch Number
(Position)
Function Effect
1
1 (ON), 2 (OFF)
1 (OFF), 2 (ON)
Normal Open mode
Normal Close mode
2
3 (ON), 4 (OFF)
3 (OFF), 4 (ON)
Normal Open mode
Normal Close mode
3
5 (ON), 6 (OFF)
5 (OFF), 6 (ON)
Normal Open mode
Normal Close mode
4
7 (ON), 8 (OFF)
7 (OFF), 8 (ON)
Normal Open mode
Normal Close mode
Camera ID Setting
This camera has the camera ID set to “0” at the time
of the shipment. If you use 2 cameras or more
simultaneously, change the ID to “2” using the 8-bit
DIP switch of the 2 camera with a screwdriver.
Set the camera ID setting referring to the pictures
and the table on the below.
• The default setting of the camera ID is 0.
ON
1
2
3
4
5
6
SW1 on main board
10
7
8
SW1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
SW2
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
SW3
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
SW4 SW5
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
SW6
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW7 SW8
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
LPT-EP500_ENG
ID
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
SW1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
11/4/15
SW2
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
SW3
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
9:43 AM
SW4 SW5
OFF ON
OFF ON
OFF ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
ON OFF
ON OFF
Page 11
SW6
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW7 SW8
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ID
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
SW1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
SW2
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
SW3
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
SW4 SW5
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW6
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW7 SW8
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
11
LPT-EP500_ENG
ID
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
12
11/4/15
9:43 AM
SW1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
SW3
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
SW2
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
Page 12
SW4 SW5
ON
ON
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
OFF ON
OFF ON
OFF ON
OFF ON
SW6
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW7 SW8
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ID
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
SW1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
SW2
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
SW3
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
SW4 SW5
OFF ON
OFF ON
OFF ON
OFF ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
OFF OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW6
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW7 SW8
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
LPT-EP500_ENG
11/4/15
9:43 AM
Page 13
Connections
Connection Preview
AC 24V
Video output
AC 24V cable for Camera
BNC plug
data port A
Ethernet cable
data port B
Ethernet cable
data port C
Ethernet cable
Precautions
RS-485 Connection
•
The connections should be made by qualified
service personnel or system installers in accordance with all local codes.
•
AC 24V can be used.
Use the cable that is described below for RS-485 site
communication.
• Shielded, twisted pair cable
• Low impedance
• Wire gauge size is thicker than AWG #22 (0.33 mm2).
Note: When powered up, the unit performs a selfcheck (including one panning, tilting, zooming and
focusing operation).
13
LPT-EP500_ENG
11/4/15
9:43 AM
Page 14
ALARM IN Connections
An 8-pin harness are supplied with the camera as
standard accessories. Connect external sensors to
this connector. Input specifications are low-active,
non-voltage contact (ON when active) or open
collector (Low when active).
• Auto mode: Change the observe position to a sensor that senses a touch or shock then return to the
position that previously observed. . (Set the
Duration Time of Alarm Input function to “1 to 255”.)
<Example : If this unit receives signal from “Alarm 8”>
Cautions
• Alarm input connection must be connected to only
one port of two communication ports.
• Do not connect one alarm sensor to the several
camera’s alarm input connector.
What is Alarm Input function?
This speed dome camera has a terminal that can
sense the alarm signals.
If the alarm sensor that has installed in a door,
window, safe etc. sense a touch or shock, the alarm
sensor send the alarm signal to the camera and the
camera will observe the sensed position.
There are “Manual mode” and “Auto mode” for the
Alarm Input function.
• Manual mode: Change the observe position to a
sensor that senses a touch or shock then keep
observe the sensed position. (Set the Duration Time
of Alarm Input function to “0”.)
<Example : If this unit receives signal from “Alarm 8”>
14
Note : The Alam In 1 is Preset 1, Alam In 2 is Preset 2,
Alam In 3 is Preset 3,...,Alam In 7 is Preset 7
and Alam In 8 is Preset 8.
LPT-EP500_ENG
11/4/15
9:43 AM
Page 15
Alarm Input function
Listed below are the camera actions of alarm input function by different function status in each mode
Function status
Manual mode
Auto mode
While observe a specific
position.
Change the observe position to the
alarmed position then keep observe
the alarmed position.
Change the observe position to the
alarmed position then return to the
position that previously observed.
While operating Preset
Tour function.
Stop preset touring and change the
observe position to the alarmed position then keep observe the alarmed
position.
Stop preset touring and change the
observe position to the alarmed
position then restart the preset touring
again.
While operating Auto
Pan function.
Stop auto panning and change the
observe position to the alarmed
position then keep observe the
alarmed position.
Stop auto panning and change the
observe position to the alarmed
position then restart the auto panning
again.
While operating Pattern
function.
Stop operating pattern function and
change the observe position to the
alarmed position then keep observe
the alarmed position.
Stop operating pattern function and
change the observe position to the
alarmed position then restart the pattern function again.
ALARM OUT Connections
Connect an external device, for example, a buzzer or lamp, to this connector. Output specifications are lowactive, open-collector and a drive capacity of 30V DC 0.5A maximum.
Alarm output numbers 1 to 4 are linked to alarm inputs 1 to 4 respectively. If alarm input 1 comes in, the camera sends output signals via the alarm output 1 connector on the camera.
Note: Use a relay if the voltage or current of the connected device exceeds the ratings.
15
LPT-EP500_ENG
11/4/15
9:43 AM
Page 16
Data Port Connections
Data Port A
Data Port B
Data Port C
16
White
Blue
Green
Yellow
Orange
Red
Brown
Black
8
7
6
5
4
3
2
1
White
Blue
Green
Yellow
Orange
Red
Brown
Black
8
7
6
5
4
3
2
1
White
Blue
Green
Yellow
Orange
Red
Brown
Black
8
7
6
5
4
3
2
1
To Alarm sensors
TXD + RS-485
TXD - Connection
To Alarm sensors
To Alarm sensors
TXD + RS-485
TXD - Connection
To Alarm sensors
To Alarm indicator 4
To Alarm indicator 3
To Alarm indicator 2
To Alarm indicator 1
LPT-EP500_ENG
11/4/15
9:43 AM
Page 17
System Connection
Note: When any peripheral is turned off and turned on again, the camera is also turned off
and turned back on.
Caution: Connect the supplied
termination adapter to the final
camera’s data port (B) to prevent
the RS-485 communication error.
Caution: Do not connect the alarm connectors to the another camera’s alarm connectors.
17
LPT-EP500_ENG
11/4/15
9:43 AM
Page 18
Adapter Connections
The adapter is used to connect to another camera, alarm sensor, or controller with RS-485 protocol, etc.
Data Port A
Data Port B
Data Port C
18
Brown
Blue
Yellow
Green
Red
Black
Orange
White
1
2
3
4
5
6
7
8
ALARM IN 1
ALARM IN 2
GND
TRX DTRX D+
GND
ALARM IN 3
ALARM IN 4
Brown
Blue
Yellow
Green
Red
Black
Orange
White
1
2
3
4
5
6
7
8
ALARM IN 5
ALARM IN 6
GND
TRX DTRX D+
GND
ALARM IN 7
ALARM IN 8
Brown
Blue
Yellow
Green
Red
Black
Orange
White
1
2
3
4
5
6
7
8
ALARM OUT 1
COM 1
ALARM OUT 2
COM 2
ALARM OUT 3
COM 3
ALARM OUT 4
COM 4
To Alarm sensor
TXD RS-485 Connecti
TXD +
To Alarm sensor
To Alarm sensor
TXD RS-485 Connecti
TXD +
To Alarm sensor
To Alarm indicator 1
To Alarm indicator 2
To Alarm indicator 3
To Alarm indicator 4
LPT-EP500_ENG
11/4/15
9:43 AM
Page 19
Setup Menu
Setup Menu Overview
Setup menus are shown in the table below. You can adapt the camera to your requirements by setting up the
respective items in these menus. Menus are incorporated in a hierarchical structure, from the setup menu at
the top to manual mask area selection at the bottom. These menus are described on the following pages for
reference. Switches, keys and the joystick are used in the setup operations
Main Menu
Sub Menu
CAMERA ID
FOCUS SET
AWB SET
AE MODE
AE LEVEL
Page
21
Main Menu
Sub Menu
SPECIAL SET
Page
USER TITLE
28
21
SHARPNESS
28
FOCUS DIST
21
COLOR
29
ZOOM START
22
NEGATIVE
29
ZOOM END
22
ZOOM SPEED
22
ZTRK MODE
22
FOCUS MODE
MOTION DET
29
30
LEVEL SET
30
WBC MODE
23
FUNCTION
30
RED ADJUST
23
MOTION DET
30
BLUE ADJUST
23
CAMERA ID
30
AE MODE
24
ZOOM MAG
30
IRIS ADJUST
24
USER TITLE
30
AGC ADJUST
25
INIT TITLE
30
BRIGHTNESS
25
P MASKING
BACKLIGHT
25
EXIT
E SENSITIVE
26
FLICKERLESS
26
SHUTTER
26
BLC LEVEL
27
WDR LEVEL
27
OSD DISP
D EFFECT
DETECTION
31
Exits the menu.
-
Note: The Preset, Auto Pan, Pattern, Alarm, Privacy Mask functions could not be set on the OSD menu.
To set these functions, use LCC-K1000 protocol or Multix protocol.
19
LPT-EP500_ENG
11/4/15
9:43 AM
Page 20
Setting Camera Menu
The buttons on the connected controller are used for
setup.
LCC-K1000 Controller (Optional)
OSD button
FOCUS
FOCUS MODE
FOCUS DIST
ZOOM START
ZOOM END
ZOOM SPEED
ZTRK MODE
INITIAL SET
RETURN
PUSH AUTO
50CM
x1
x54
QUICK
AUTO
ON
4. Use ZOOM (In/Out) to select a submenu option.
5. Use FOCUS (Near/Far) to select a value.
6. To close MENU, select [EXIT] option on the
MENU then press FOCUS (Near/Far).
CLR (CLEAR) button
Arrow buttons
SEL (SELECT) button
ZOOM buttons
FOCUS buttons
To return to MENU screen from submenu
Use ZOOM (In/Out) to select [RETURN] option then
press FOCUS (Near/Far) button on the sub menu.
Open Menu Display
1. Select the number of the camera you want to set
up and a monitor to display MENU.
2. Press OSD button on the controller.
Note: Please refer to the manuals of the controller for details.
3. Use ZOOM (In/Out) to select an option then press
FOCUS (Near/Far) button.
Submenu appears on the monitor.
MENU
CAMERA ID
0
FOCUS SET
AWB SET
AE MODE
AE LEVEL
SPECIAL SET
MOTION DET
F OSD DISP
P MASKING
EXIT
20
To exit MENU screen
Use ZOOM (In/Out) to select [EXIT] option then
press FOCUS (Near/Far) button on the main menu.
To reset your parameters to the factory
default settings
Use ZOOM (In/Out) to select [INITIAL SET] option
then press FOCUS (Near/Far) button on the menu.
LPT-EP500_ENG
11/4/15
9:43 AM
Page 21
Camera Identification Setting
Only displays the camera’s ID. Use the internal
8 bit-DIP switch if you want to set ID.
• Camera ID 0 can control all of camera independent of camera ID number.
MENU
CAMERA ID
0
FOCUS SET
AWB SET
AE MODE
AE LEVEL
SPECIAL SET
MOTION DET
F OSD DISP
P MASKING
EXIT
Focus Settings
To avoid AF error or out of Focus,initialization of
LENS system by using the "Remote Reset"
command of Controller is highly recommended.
General Operation
1. Move the cursor to [FOCUS SET] on the [MENU]
screen
2. Press the right key and the FOCUS setting menu
appears.
FOCUS
FOCUS MODE
FOCUS DIST
ZOOM START
ZOOM END
ZOOM SPEED
ZTRK MODE
INITIAL SET
RETURN
PUSH AUTO
50CM
x1
x54
QUICK
AUTO
ON
3. Move the cursor to the desired option.
4. Select an option (or value).
5. To reset the [FOCUS] settings to factory setting,
use [INITIAL SET] option on the [FOCUS] menu.
6. To return to the previous menu, use [RETURN]
option on the [FOCUS] menu.
Focus Mode setting
Select [FOCUS MODE] option on the [FOCUS]
menu, then select the following mode.
• PUSH AUTO: Auto-focus is activated only when
the Push Auto key on the controller is pressed.
• MANUAL: Focus is activated only when the
FOCUS (NEAR or FAR) keys on the controller is
pressed.
• AUTO: Auto-focus is activated automatically while
a manual pan, tilt or zoom operation is performed.
Note:
• If you press the FOCUS (NEAR or FAR) button on
the controller while Auto-focus mode, the focus
mode is automatically changed to [MANUAL].
• If you want to activate the full-time auto focus
mode while a Pan/Tilt operation, set the focus
mode to AUTO.
FOCUS
FOCUS MODE
FOCUS DIST
ZOOM START
ZOOM END
ZOOM SPEED
ZTRK MODE
INITIAL SET
RETURN
PUSH AUTO
50CM
x1
x54
QUICK
AUTO
ON
Focus Distance setting
Selects the minimum shooting distance for the focus.
Select [FOCUS DIST] option on the [FOCUS] menu,
then select a Focus Distance value. (1CM, 10CM,
50CM, 1M, 3M, 5M)
FOCUS
FOCUS MODE
FOCUS DIST
ZOOM START
ZOOM END
ZOOM SPEED
ZTRK MODE
INITIAL SET
RETURN
PUSH AUTO
50CM
x1
x54
QUICK
AUTO
ON
21
LPT-EP500_ENG
11/4/15
9:43 AM
Page 22
Zoom Start setting
Zoom Speed setting
Selects a zoom start position.
Selects a zoom speed.
Select [ZOOM START] option on the [FOCUS] menu,
then select a zoom’s start position. (x1 - x26)
Select [ZOOM SPEED] option on the [FOCUS]
menu, then select a zoom speed. (SLOW, MIDDLE,
QUICK)
FOCUS
FOCUS
FOCUS MODE
FOCUS DIST
ZOOM START
ZOOM END
ZOOM SPEED
ZTRK MODE
INITIAL SET
RETURN
PUSH AUTO
50CM
x1
x54
QUICK
AUTO
ON
FOCUS MODE
FOCUS DIST
ZOOM START
ZOOM END
ZOOM SPEED
ZTRK MODE
INITIAL SET
RETURN
PUSH AUTO
50CM
x1
x54
QUICK
AUTO
ON
Zoom End setting
Selects a zoom end position.
Zoom Tracking Mode setting
Select [ZOOM END] option on the [FOCUS] menu,
then select a zoom’s end position.
(Zoom Start position+1 - x54)
Selects a zoom tracking mode. Zoom tracking means
focused zooming state.
Select [ZTRK MODE] option on the [FOCUS] menu,
then select a zoom tracking mode (AUTO, MANUAL).
FOCUS
FOCUS MODE
FOCUS DIST
ZOOM START
ZOOM END
ZOOM SPEED
ZTRK MODE
INITIAL SET
RETURN
22
PUSH AUTO
50CM
x1
x54
QUICK
AUTO
ON
FOCUS
FOCUS MODE
FOCUS DIST
ZOOM START
ZOOM END
ZOOM SPEED
ZTRK MODE
INITIAL SET
RETURN
PUSH AUTO
50CM
x1
x54
QUICK
AUTO
ON
LPT-EP500_ENG
11/4/15
9:43 AM
Page 23
White Balance Control Settings
You can set the white balance options using the
[AWB] menu.
General Operation
1. Move the cursor to [AWB SET] on the [MENU]
screen.
MENU
CAMERA ID
0
FOCUS SET
AWB SET
AE MODE
AE LEVEL
SPECIAL SET
MOTION DET
F OSD DISP
P MASKING
EXIT
s
).
2. Press the right key and the AWB setting menu
appears.
AWB
WBC MODE
AUTO
RED ADJUST NOT USED
BLUE ADJUST NOT USED
INITIAL SET
ON
RETURN
3. Move the cursor to the desired option.
4. Select an option (or value).
5. To reset the [AWB] settings to factory setting, use
[INITIAL SET] option on the [AWB] menu.
Setting the WBC (White Balance
Control) Mode
You can select one of four modes for white balance
adjustment.
Select [WBC MODE] option on the [AWB] menu, then
select the following mode.
• AUTO (Auto-Tracing White Balance): In this mode,
the color temperature is monitored continuously
and thereby white balance is automatically set.
The color temperature range for the proper white
balance is approximately 2 500 - 9 500K. Proper
white balance may not be obtained under the following conditions:
1) The color temperature is out of the 2 500 9 500K range.
2) When the scene contains mostly high color
temperature objects, such as a blue sky or
sunset.
3) When the scene is dim.
• INDOOR: The color temperature range for the
proper white balance is approximately 3 200K.
• OUTDOOR: The color temperature range for the
proper white balance is approximately 5 100K.
• MANUAL: You can set the white balance options
manually.
1) RED ADJUST: Obtains the optimum amount
of red gain.
2) BLUE ADJUST: Obtains the optimum amount
of blue gain.
AWB
WBC MODE
MANUAL
RED ADJUST 124
BLUE ADJUST 92
INITIAL SET
OFF
RETURN
6. To return to the previous menu, use [RETURN]
option on the [AWB] menu.
• PUSH AUTO: The White Balance will be adjusted
automatically.
23
LPT-EP500_ENG
11/4/15
9:43 AM
Page 24
Exposure Settings
You can set the exposure options using the [AE]
menu.
General Operation
1. Move the cursor to [AE] on the [MENU] screen
MENU
CAMERA ID
0
FOCUS SET
AWB SET
AE MODE
AE LEVEL
SPECIAL SET
MOTION DET
F OSD DISP
P MASKING
EXIT
2. Press the right key and the exposure setting
menu appears.
AE
AE MODE
AUTO
IRIS ADJUST
AUTO
AGC ADJUST AUTO
BRIGHTNESS 128
BACKLIGHT
OFF
E SENSITIVE x10 AUTO
FLICKERLESS OFF
SHUTTER
AUTO
INITIAL SET
ON
RETURN
AE Mode setting
Selects an Automatic Exposure mode.
Select [AE MODE] option on the [AE] menu, then
select an Automatic Exposure mode.
• AUTO: Use to compensate the exposure automatically.
• IRIS MAN: Use to change the value of Lens’ Iris
(IRIS of lens is fixed manually, and the action of
exposure compensation depend on its of AGC).
• SLOW MAN: The change of Electronic Sensitive is
available (x1 FIX - x20 FIX). (Electronic Sensitive
of camera is fixed manually.)
• SHUT MAN: Use to change the Shutter Speed
control. In this time, AE mode act automatically
(10 steps control is available).
AE
AE MODE
AUTO
IRIS ADJUST
AUTO
AGC ADJUST AUTO
BRIGHTNESS 128
BACKLIGHT
OFF
E SENSITIVE x10 AUTO
FLICKERLESS OFF
SHUTTER
AUTO
INITIAL SET
ON
RETURN
Iris Adjust setting
3. Move the cursor to the desired option.
4. Select an option (or value).
5. To reset the [AE] settings to factory setting, use
[INITIAL SET] option on the [AE] menu.
6. To return to the previous menu, use [RETURN]
option on the [AE] menu.
24
Selects a iris’ exposure value. This option is available
only when [AE MODE] is set to [IRIS MAN].
Select [IRIS ADJUST] option on the [AE] menu, then
select a value. (0 - 255)
AE
AE MODE
AUTO
IRIS ADJUST AUTO
AGC ADJUST AUTO
BRIGHTNESS 128
BACKLIGHT
OFF
E SENSITIVE x10 AUTO
FLICKERLESS OFF
SHUTTER
AUTO
INITIAL SET
ON
RETURN
LPT-EP500_ENG
11/4/15
9:43 AM
Page 25
Automatic Gain Control (AGC) setting
Backlight Setting
If the images are too dark, change the maximum
[AGC] value to make the images lighter. This option
is available only when [AE MODE] is set to [SLOW
MAN] or [SHUT MAN].
Improves an image that is darkened because of
backlighting.
Select [AGC ADJUST] option on the [AE] menu, then
select a value. (0 - 7)
AE
AE MODE
AUTO
IRIS ADJUST
AUTO
AGC ADJUST 0
BRIGHTNESS 128
BACKLIGHT
OFF
E SENSITIVE x10 AUTO
FLICKERLESS OFF
SHUTTER
AUTO
INITIAL SET
ON
RETURN
Select [BACKLIGHT] option on the [AE] menu, then
select a value.
AE
AE MODE
AUTO
IRIS ADJUST
AUTO
AGC ADJUST 0
BRIGHTNESS 128
BACKLIGHT
OFF
E SENSITIVE x10 AUTO
FLICKERLESS OFF
SHUTTER
AUTO
INITIAL SET
ON
RETURN
• OFF: The back light compensation is not used.
• ON: The back light compensation is used.
Brightness Setting
The lens iris is fixed at the value that you have set
regardless of the brightness of an object. This option
is available only when [AE MODE] is set to [AUTO].
Select [BRIGHTNESS] option on the [AE] menu, then
select a value. (0 - 255)
AE
AE MODE
AUTO
IRIS ADJUST
AUTO
AGC ADJUST 0
BRIGHTNESS 128
BACKLIGHT
OFF
E SENSITIVE x10 AUTO
FLICKERLESS OFF
SHUTTER
AUTO
INITIAL SET
ON
RETURN
• AUTO (Auto back light compensation): If you use
an ordinary camera when there is an intense and
concentrated illumination behind an object, the
back light will shade the image on the monitor
screen. The Backlight function prevents such a
back light effect to secure a clear image under all
illumination environments.
• WDR: The WDR camera is state of the art to
enlarge the screen profit effectively, especially for
taking photos of a window in a building. In short it
revives both the indoor and outdoor status as they
are clearly.
25
LPT-EP500_ENG
11/4/15
9:43 AM
Page 26
Electronic Sensitive setting
Shutter Speed Setting
The electronic sensitivity enhancement function
varies the shutter speed to increase the sensitivity in
low light conditions.
You can select a shutter speed from among AUTO,
1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000,
1/10000, 1/20000 and 1/50000 seconds.
This option is available only when [AE MODE] is set
to [AUTO] and [FLICKERLESS] option is set to
[OFF].
This option is available only when [AE MODE] is set
to [AUTO] or [SLOW MAN].
Select [E SENSITIVE] option on the [AE] menu, then
select a value.
There are two modes for Electronic Sensitive as follows:
AUTO mode: OFF, x2 AUTO - x20 AUTO (If you
select x20 AUTO, the sensitivity is increased automatically up to x20.)
SLOW MAN mode: x1 FIX - x20 FIX (If you select
x20 FIX, the sensitivity is increased to a fixed x20.)
AE
AE MODE
AUTO
IRIS ADJUST
AUTO
AGC ADJUST 0
BRIGHTNESS 128
BACKLIGHT
OFF
E SENSITIVE x10 AUTO
FLICKERLESS OFF
SHUTTER
AUTO
INITIAL SET
ON
RETURN
Flickerless Setting
Use for removing the flicker of picture. This option is
available only when [AE MODE] is set to [AUTO].
Select [FLICKERLESS] option on the [AE] menu,
then select an option (ON or OFF). Set to [ON] to
remove the flicker.
AE
AE MODE
AUTO
IRIS ADJUST
AUTO
AGC ADJUST 0
BRIGHTNESS 128
BACKLIGHT
OFF
E SENSITIVE x10 AUTO
FLICKERLESS OFF
SHUTTER
AUTO
INITIAL SET
ON
RETURN
26
Select [SHUTTER] option on the [AE] menu, then
select a shutter speed.
AE
AE MODE
AUTO
IRIS ADJUST
AUTO
AGC ADJUST 0
BRIGHTNESS 128
BACKLIGHT
OFF
E SENSITIVE x10 AUTO
FLICKERLESS OFF
SHUTTER
AUTO
INITIAL SET
ON
RETURN
LPT-EP500_ENG
11/4/15
9:43 AM
Page 27
Auto Exposure Level Settings
You can set the auto exposure options using the
[AE LEVEL] menu.
General Operation
1. Move the cursor to [AE LEVEL] on the [MENU]
screen.
MENU
CAMERA ID
0
FOCUS SET
AWB SET
AE MODE
AE LEVEL
SPECIAL SET
MOTION DET
F OSD DISP
P MASKING
EXIT
2. Press the right key and the auto exposure level
setting menu appears.
AE LEVEL
BLC LEVEL
WDR LEVEL
INITIAL SET
RETURN
176
6
ON
BLC (Back Light Compensation) Level
Setting
Selects a level for the BLC (back light compensation).
Select [BLC LEVEL] option on the [AE LEVEL] menu,
then select a desired level (0-255).
AE LEVEL
BLC LEVEL
WDR LEVEL
INITIAL SET
RETURN
176
6
ON
WDR (Wide Dynamic Range) Level
setting
Selects a level for the WDR (Wide Dynamic Range).
Select [WDR LEVEL] option on the [ AE LEVEL]
menu, then select a desired level (0-255).
AE LEVEL
3. Move the cursor to the desired option.
BLC LEVEL
WDR LEVEL
INITIAL SET
RETURN
176
6
ON
4. Select an option (or value).
5. To reset the [AE LEVEL] settings to factory setting, use [INITIAL SET] option on the [AE LEVEL]
menu.
6. To return to the previous menu, use [RETURN]
option on the [AE LEVEL] menu.
27
LPT-EP500_ENG
11/4/15
9:43 AM
Page 28
Special Settings
You can set the special options using the [SPECIAL]
menu.
General Operation
1. Move the cursor to [SPECIAL SET] on the
[MENU] screen
MENU
CAMERA ID
0
FOCUS SET
AWB SET
AE MODE
AE LEVEL
SPECIAL SET
MOTION DET
F OSD DISP
P MASKING
EXIT
2. Press the right key and the [SPECIAL] setting
menu appears.
SPECIAL
m
USER TITLE
SHARPNESS
COLOR
NEGATIVE
D EFFECT
INITIAL SET
RETURN
■■■■■■■■■■
112
ON
OFF
NONE
ON
3. Move the cursor to the desired option.
4. Select an option (or value).
5. To reset the [SPECIAL] settings to factory setting,
use [INITIAL SET] option on the [SPECIAL]
menu.
6. To return to the previous menu, use [RETURN]
option on the [SPECIAL] menu.
28
User Title Setting
C
You can name the camera independently.
Y
c
1. Move the cursor to [USER TITLE] on the
[SPECIAL] menu. Arrow mark appears.
2. Move the arrow mark to the desired position then
select a character.
3. Repeat step 2 to set the remain characters.
S
s
t
t
SPECIAL
m
USER TITLE
SHARPNESS
COLOR
NEGATIVE
D EFFECT
INITIAL SET
RETURN
■■■■■■■■■■
112
ON
OFF
NONE
ON
Sharpness Setting
N
Sharpens the image outline.
Y
Select [SHARPNESS] option on the [SPECIAL]
menu, then select a value. (0 - 255)
S
t
SPECIAL
USER TITLE
SHARPNESS
COLOR
NEGATIVE
D EFFECT
INITIAL SET
RETURN
■■■■■■■■■■
112
ON
OFF
NONE
ON
LPT-EP500_ENG
11/4/15
9:43 AM
Page 29
Color Setting
Digital Effect Setting
You can switch the displayed picture to grayscale or
color.
You cannot set a Digital Effect option.
Select [COLOR] option on the [SPECIAL] menu, then
select an option (ON or OFF). Set to [ON] to display
the picture with color. Set to [OFF] to display the picture with grayscale.
SPECIAL
USER TITLE
SHARPNESS
COLOR
NEGATIVE
D EFFECT
INITIAL SET
RETURN
■■■■■■■■■■
112
ON
OFF
NONE
ON
SPECIAL
USER TITLE
SHARPNESS
COLOR
NEGATIVE
D EFFECT
INITIAL SET
RETURN
■■■■■■■■■■
112
ON
OFF
NONE
ON
Negative Setting
You can use the negative effect.
Select [NEGATIVE] option on the [SPECIAL] menu,
then select an option (ON or OFF).
SPECIAL
USER TITLE
SHARPNESS
COLOR
NEGATIVE
D EFFECT
INITIAL SET
RETURN
■■■■■■■■■■
112
ON
OFF
NONE
ON
29
LPT-EP500_ENG
11/4/15
9:43 AM
Page 30
Motion Detection Setting
The motion detection detects the moving objects in
the scene by monitoring changes in brightness level.
You can select the level of sensitivity for motion
detection.
When this camera is connected to a compatible intelligent CCTV system, the camera transmits an alarm
signal by multiplexing it with the video signal.
1. Move the cursor to [MOTION DET] on the
[MENU] screen
MENU
CAMERA ID
0
FOCUS SET
AWB SET
AE MODE
AE LEVEL
SPECIAL SET
MOTION DET
F OSD DISP
P MASKING
EXIT
2. Press the right key and the [MOTION] setting
menu appears.
Function On-Screen Display
Setting
You can set the Function On-Screen Display options
using the [F OSD] menu.
The Function On-Screen Display of this camera can
be turned on or off.
1. Move the cursor to [F OSD DISP] on the [MENU]
screen
MENU
CAMERA ID
0
FOCUS SET
AWB SET
AE MODE
AE LEVEL
SPECIAL SET
MOTION DET
F OSD DISP
P MASKING
EXIT
2. Press the right key and the [F OSD] setting menu
appears.
F OSD
MOTION
DETECTION
LEVEL
DAY/NIGHT
INITIAL SET
RETURN
ON
10
AUTO
ON
3. Set [DETECTION] option to [ON] to use.
4. Use [LEVEL] option to obtain the optimum detection level (21 levels).
5. Use [DAY/NIGHT] option for day/night function.
AUTO: The camera selects black and white mode
if the picture is dark, or color mode if the picture
is bright enough.
NIGHT: Black-and-white mode enabled.
DAY: Color mode enabled.
6. To reset the [MOTION] settings to factory setting,
use [INITIAL SET] option on the [MOTION] menu.
7. To return to the previous menu, use [RETURN]
option on the [MOTION] menu.
30
FUNCTION
MOTION DET
CAMERA ID
ZOOM MAG
USER TITLE
INIT TITLE
INITIAL SET
RETURN
DISP ON
DISP ON
DISP ON
DISP ON
DISP ON
DISP ON
ON
3. Select an option (DISP ON or OFF).
• DISP ON: Displays the Function On-Screen
Display on the screen.
• OFF: The Function On-Screen Display dose
not appear on the screen.
4. To reset the [F OSD] settings to factory setting,
use [INITIAL SET] option on the [F OSD] menu.
5. To return to the previous menu, use [RETURN]
option on the [F OSD] menu.
LPT-EP500_ENG
11/4/15
9:43 AM
Page 31
Privacy Masking Settings
Using the LCC-K1000 or controller with Multix
protocol for Privacy Zone Setting.
This function is aiming at the protection of personal
privacy, selecting a screen part black not to be
displayed in the screen.
Up to 8 zones can be registered. Submenus are
provided for zone number selection and parameter
setting.
To register a new privacy zone using the
LCC-K1000
1. Press the Set Up button then select the
[PRIVACY ZONE] icon.
5. Adjust the pan, tilt, and zoom position so that the
desired position comes into the zone frame with
the joystick.
You can’t move privacy mask zone and you can’t
change the size of privacy mask zone.
6. Press SEL.
The mask color will be change into grey.
The privacy zone setting has been completed and
the setting is memorized in the camera’s memory.
7. Repeat steps 3-6 to add additional position.
To register a new privacy zone using the
other controller with Multix protocol
You must use the LCC-K1000 controller to set the
privacy mask zone. If you use the other controller or
unit with Multix Protocol, refer to follow steps.
1. Use the command below to display the blue zone
frame on the center of monitor to set the privacy
mask zone.
2. Press SEL.
The sub menu will appear for [PRIVACY ZONE]
setting.
3. Select [Set Zone Area] option then press SEL.
The sub menu will appear.
Guide Code 0x01 Dome ID
0x81
(0xE5)
0x01 Index of 0x00 Check
Mask
sum
2. Adjust the pan, tilt and zoom position so that the
desired position comes into the zone frame.
3. Use the command below to confirm the privacy
mask setting.
Guide Code 0x01 Dome ID
(0xE5)
0x81
0x02 Index of 0x00 Check
Mask
sum
4. The mask color will be changed into gray if the
privacy zone settings are completed. The settings
are memorized in the camera's memory.
Notes:
4. Use number buttons to select the zone index
number then press SEL to confirm.
The blue zone frame appears on the center of
monitor.
•
The Check sum is calculated by performing the
8bit sum of the all bytes except check sum.
•
The P MASKING menu option of the camera is
used for factory control. If you set the privacy
mask zone using the P MASKING menu option of
the camera, the privacy mask function may cause
a malfunction.
•
Please contact authorized service center or where
you purchased to know the all of the protocol.
31
LPT-EP500_ENG
11/4/15
9:43 AM
Page 32
Reference
Specifications
Signal System
Pick-Up Device
Total Pixels No.
S/N Ratio
Horizontal Resolution
Lens
Shooting Distance
On Screen Display
Minimum Illumination
NTSC (High Resolution)
PAL (High Resolution)
1/4” Super HAD CCD
410K
470K
More Than 50 dB
More Than 520 TV Lines
X 27 Zoom (F 1.5(W), F 3.8(T) f=3.25-88.0 mm)
Tele (1.2m), Wide (0.01 m)
On/Off (English only)
1 Lux (F1.5, normal shutter)
0.03 Lux (20 Field Accumulated)/
0 Lux (Infrared ON: Night Mode)
Digital Zoom
x 2: Basic (Off at WDR)
Sync System
Internal
White Balance
Auto (ATW)/ Indoor/ Outdoor/ Manual/ Push Auto
Control Method
RS-485 Control
Alarm Input
8 Channel
Alarm Output
4 Channel
Video Output
Composite Output 1 Vp-p, 75Ω
Electronic Shutter
1/4- 1/50,000 Sec (10 Step)
Flickerless Mode
Manual On/Off
Iris Control
Auto / Manual
Wide Dynamic Range
Dual Shutter control (128 times of Dynamic Range)
Panning Range (Speed)
0° - 360° (240° / Sec)
Tilting Range (Speed)
0° - 180° (240° / Sec)
Privacy Zone
8 Area Active Programmable Zone
Preset / ID
128 Position / 256
Auto Panning
2 - 8 points
Pattern
Max. 8 minutes
Group Tour
Max. 9 Groups
Operation Temperature
-10° - 50°C
Safekeeping Temperature
-20° - 60°C
Power Supply
AC 24V
Power Consumption
Max. 29W
Dimension (ø x H)
LPT-EP551PS/LPT-EP553PS: ø230 x 300 mm
LPT-EI551PS/LPT-EI553PS: ø220 x 170 mm
Weight
LPT-EP551PS/LPT-EP553PS: Approx 3.3Kg
LPT-EI551PS/LPT-EI553PS: Approx 2.6Kg
32
Download PDF

advertising