LG | LS501P-B1 | LG LS501P-B1 Owner’s Manual

Color Video Camera
Instruction Manual
Models : LS501
Before installing, operating or adjusting
this product, please read this instruction
booklet carefully and completely.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.
FCC WARNING: This equipment may generate or
use radio frequency energy. Changes or modifications
to this equipment may cause harmful interference
unless the modifications are expressly approved in the
instruction manual. The user could lose the authority
to operate this equipment if an unauthorized change or
modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
• A suitable conduit entries, knock-outs or glands
shall be provided in the cable entries of this product in the end user.
• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
•
Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall
be provided with brushings.
Warning: Do not install this equipment in a confined
space such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with
the National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate
measures.
Warning: To reduce a risk of fire or electric shock, do
not expose this product to rain or moisture.
Caution: This installation should be made by a qualified service person and should conform to all local
codes.
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
To disconnect power from the mains, pull out the
mains cord plug. When install the product, ensure
that the plug is easily accessible.
Disposal of your old appliance
1.When this crossed-out wheeled bin symbol is
attached to a product it means the product is
covered by the European Directive 2002/96/
EC.
2.All electrical and electronic products should
be disposed of separately from the municipal
waste stream via designated collection facilities appointed by the government or the local
authorities.
3. The correct disposal of your old appliance will
help prevent potential negative consequences
for the environment and human health.
4. For more detailed information about disposal
of your old appliance, please contact your
city office, waste disposal service or the shop
where you purchased the product.
LG Electronics hereby declares that this/
these product(s) is/are in compliance with
the essential requirements and other relevant provisions of Directive 2004/108/EC,
2006/95/EC, and 2009/125/EC.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : +31-(0)36-547-8888)
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install
in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete
outlet.
10.Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11.Only use attachments/accessories specified by
the manufacturer.
12.Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13.Unplug this apparatus during lightning storms
or when unused for long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
Contents
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Motion Detection setting . . . . . . . . . . . . . . . . 28
Cautions for Safe Operation . . . . . . . . . . . . . . 7
3D-DNR setting . . . . . . . . . . . . . . . . . . . . . . . 29
Part Names and Functions . . . . . . . . . . . . . . . 8
Privacy Mask setting . . . . . . . . . . . . . . . . . . . 30
Connections . . . . . . . . . . . . . . . . . . . . . . . . . .11
Special menu settings . . . . . . . . . . . . . . . . . . 31
Mounting the Lens . . . . . . . . . . . . . . . . . . . . . 12
Reset settings . . . . . . . . . . . . . . . . . . . . . . . . 36
Concerning Auto-Iris Lenses . . . . . . . . . . . . . 14
Specification . . . . . . . . . . . . . . . . . . . . . . . . . 37
Flange-back Adjustment . . . . . . . . . . . . . . . . 15
Installation of Camera . . . . . . . . . . . . . . . . . . 16
Menu Operation . . . . . . . . . . . . . . . . . . . . . . . 17
Camera Identification Settings . . . . . . . . . . . 20
Exposure settings . . . . . . . . . . . . . . . . . . . . . 21
White Balance setting . . . . . . . . . . . . . . . . . . 25
Day/Night setting . . . . . . . . . . . . . . . . . . . . . . 27
Features
This color video camera is designed for use in monitoring system.
•
High resolution and high sensitivity with a 6 mm Super HAD CCD (Charge Coupled Device).
•
Line Lock when using AC 24 V.
•
C/CS Mount.
•
Auto White Balance
•
Auto exposure with (Auto) Iris control
•
Day & Night function
Cautions for Safe Operation
Power Supply
Operating and storage location
This camera must be operated AC 24 V or DC 12 V
Certified/Listed, class 2 power supply only.
Avoid viewing a very bright object (such as light fittings)
during an extended period. Avoid operating or storing
the unit in the following locations.
• Extremely hot or cold places (operating temperature
-10 °C to 50 °C, however, we recommend that the
unit be used within a temperature range of 0 °C to
45 °C)
• Damp or dust place
• Places exposed to rain
• Places subject to strong vibration
• Close to generators of powerful electromagnetic
radiation such as radio or TV transmitters.
Note: Be careful of AC frequency when the camera is
operated with Line lock mode.
Handling of the unit
Be careful not to spill water or other liquids on the unit.
Be cautions not to get combustible or metallic material
inside the body. If used with foreign matter inside, the
camera is liable to fail or to get cause of fire or electric
shock.
• Remove dust or dirt on the surface of the lens with a
blower.
• Use a dry soft cloth to clean the body. If it is very
dirty, use a cloth dampened with a small quantity of
neutral detergent, then wipe dry.
• Avoid the use of volatile solvents such as thinners,
alcohol, benzene and insecticides.
They may damage the surface finish and/or impair
the operation of the camera.
Part Names and Functions
ab c
a Lens mount cap
The cap is installed to protect the lens
mount section. Remove the lens mount cap
before installing a lens (sold separately).
b Flange-back adjustment ring
c Camera installation bracket
The bracket can be fixed at the top or bottom of the camera.
Part Names and Functions
de f
g
d Power input terminal
AC 24 V or DC 12 V input terminal.
e GND
f Power indicator
Comes on when the power to the camera is on.
g Video output connector (BNC type)
Connect this connector to a device such as a VCR
or monitor with a VIDEO IN connector.
Part Names and Functions
i j
k
i Lens iris output connector (LENS)
This 4- pin connector is used to send the Iris control signal and power supply to an auto-iris type
lens.
j Buttons for menu
To set items on the MENU, use the these buttons
on the side panel.
k ALC Lens Setting Switch
10
•
DC: When you attach an Auto Iris lens requiring the DC control signal, please put this
switch in the DC position.
•
VIDEO: When you attach an Auto Iris lens
requiring the video control signal, please put
this switch in the VIDEO position.
Connections
Power connection
Connecting Monitor
1. Remove the insulation on the power cable as
illustrated.
The video signal connection between the camera and
the monitor or DVR.
2. Attach the terminal tips.
3. Connect to the 24 V AC / 12 V DC UL Listed,
Class 2 Power Supply only on the camera.
11
Mounting the Lens
1. Remove the lens mount cap from the camera.
2. Install the auto-iris lens.
2-1. CS mount type lens
Carefully align the lens mount with the camera
opening, then turn the lens slowly to install it.
1
2-2. C mount type lens
To allow for flange- back adjustment, install
the C-mount adaptor (option) on the lens
mount, then carefully align the lens mount with
the camera opening and turn the lens slowly
to install it.
2-2
3. Connect the lens plug to the lens iris output
connector (LENS) on the side of the camera.
When using lenses from other makers, the plug
shape may not correspond to the terminal on the
camera.
2-1
12
3
In such a case, remove the original plug and using
a soldering iron, connect a lens iris plug according
to the diagram. (Refer to next page.)
Mounting the Lens
Pin layout for the lens iris output connector
Rewire the lens iris plug
1. Cut off the plug of the lens cable, cut off approximately 8 mm of the insulation, and then strip
approximately 2 mm of the ends of the cable
sheaths.
8mm
2mm
No.
DC type lenses
VIDEO type lenses
1
Damping -
Vcc (+9 V)
2
Damping +
Not used
3
Drive +
Video
4
Drive -
Ground
2. Solder the ends of the cable wires to the ends of
the pins, and then attach the cover of the lens iris
plug.
13
Concerning Auto-Iris Lenses
DC type auto-iris lens
VIDEO type auto-iris lens
A lens without driver circuit that operates only on a DC
power source. In general, this type of lens is referred to
as DC type coil lens. (Set the ALC Lens Setting Switch
to the DC position.)
A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens
is referred to as EE amplifier type lens.
CAUTION: Depending on the type of lens used, the
lens may not perform properly.
ALC and LEVEL volume level controls are available on
the lens for iris adjustments. (Set the ALC Lens Setting
Switch to the VIDEO position.)
CAUTION:
Be cautions not to use Auto Iris Lens with over 35 mA.
14
Flange-back Adjustment
The adjustment is required only when a lens without
focus-adjusting mechanism is mounted, or when a lens
with adjusting mechanism is mounted and focus that is
more accurate is needed.
Use the flange-back adjusting ring to obtain a focused
point while watching the monitor screen.
Note:
The object may be out of focus when using a source of
near-infrared light than using the visible light.
15
Installation of Camera
The bracket can be installed to either the top of the
camera as desired. When changing the position of the
camera mounting bracket, you should always reuse the
screws that have been removed.
Note:
If using a camera mounting bracket, select a location
that is strong enough to bear the full weight of the
camera and the mounting bracket for long periods, and
install the camera and mounting bracket securely.
16
Menu Operation
The following table shows the list of menu items and
options. You can adapt the camera to your requirements by setting up the respective items in these
menus.
Main Menu
CAMERA ID
EXPOSURE
Sub Menu
-
ALC / ELC
ATW
Contents
OFF, 1 to 255
OFF/BLC/
BACKLIGHT
HSBLC
BRIGHTNESS 0 to 100
OFF/LOW/
AGC
MIDDLE/HIGH
X512, to, x2,
AUTO, OFF,
SHUTTER
A.FLK, 1/160,
to, 1/90 000
OFF / AUTO
SENS-UP
(X2, to, X128)
EXIT
RET/TOP/END
Main Menu
Sub Menu
Contents
LOW/ MIDDLE/
HIGH
5, 10, 15, 30,
DWELL TIME
60 s
EXIT
RET/TOP/END
LEVEL
DAY/NIGHT
AUTO
DAY
NIGHT
OFF
MOTION
DET
3D-DNR
ON
ZONE
AREA1 to
NUMBER
AREA4
ZONE STATE
OFF / ON
HEIGHT
WIDTH
MOVE Y
MOVE X
SENSITIVITY
EXIT
RET/TOP/END
OFF/LOW/MIDDLE/HIGH
AWCbPUSH
COLOR TEMP
WHITE BAL
MANUAL
RED
BLUE
EXIT
INDOOR,
OUTDOOR
-100 to 100
-100 to 100
RET/TOP/END
17
Menu Operation
Main Menu
PRIVACY
Sub Menu
OFF
ON
D-ZOOM
SPECIAL
D-EFFECT
SHARPNESS
STABILIZER
COLOR
SYNC
USER TITLE
LANGUAGE
EXIT
18
Contents
MASK
NUMBER
DISPLAY
COLOR
HEIGHT
WIDTH
MOVE Y
MOVE X
EXIT
OFF
AREA1 to
AREA8
OFF, ON
BLACK, GRAY,
WHITE
Main Menu
RESET
EXIT
Sub Menu
CAMERA
REBOOT
FACTORY
RESET
EXIT
Contents
RET/TOP/END
General Operation
RET/TOP/END
ZOOM
PAN
TILT
EXIT
OFF/ V-FLIP/ MIRROR/ ROTATE
0 to 68
OFF / ON
OFF / ON
INT
OFF/ON
ENG (The supported language
can be different depending on the
model.)
RET/TOP/END
1. Press
button.
The setup menu screen appears on the monitor.
ON
2. Use
or
button to select an option then press
button.
Submenu appears on the monitor.
Menu Operation
3. Use
or
4. Use
or
button to select a submenu option.
button to select a value.
to exit the setup
5. Select [EXIT] option then press
menu. In the submenu, use
or
button to
select the [EXIT] then use
or
button to select
a mode and press
to exit the setup menu.
•
•
•
RET: Return to the previous.
TOP: Return to the CAMERA SETTING menu
screen.
END: Exit the setup menu.
Notes:
•
button: Use to move upper direction on the
menu screen.
•
button: Use to move lower direction on the
menu screen.
•
button: Use for decrease the value of the
option.
•
button: Use for increase the value of the
option.
•
button: Executes selections and displays a submenu for an item with the mark.
19
Camera Identification Settings
You can use the camera identification (CAMERA ID) to
assign a number to the camera.
1. Select [CAMERA ID] option on the [CAMERA
SETTING] menu.
2. Use
255).
20
or
to select a CAMERA ID (OFF, 1 to
Exposure settings
Exposure mode setting
BACKLIGHT setting
Backlight compensation increases the exposure level
when the camera picture is darkened by the strong
background light.
1. Select [BACKLIGHT] option.
1. Select [EXPOSURE] option.
or
button to select a mode.
2. Use
(ALCy ELC)
button.
3. Press
Submenu appears on the monitor.
2. Use
.
•
or
button to select a mode then press
BLC: Set the BLC limit.
- BLC LEVEL: LOW y MIDDLE y HIGH
21
Exposure settings
•
HSBLC: Use for adjusting brightness the
specific area of picture. The HSBLC mode is
automatically activated only in low illuminance
scene.
- AREA SETTING: Use
or
button to
select a area then use
or
button to
select a ON or OFF. Press
to exit the
area setting menu.
BRIGHTNESS setting
You can increase the brightness of the darkened video.
If you set the brightness to lower value, the image is
darkened. If you set the brightness to higher value, the
image gets bright.
1. Select [BRIGHTNESS] option on the [EXPOSURE]
menu.
- GRAY SCALE: Use
or
button to
select a gray scale.
(GRAYyD.GRAYyBLACK).
- USER SCALE: Use
or
button to
select a bright level. (5 level)
- MASK: Use
or
button to select [ON]
or [OFF].
If you set the MASK to ON, the mask function is activate only when the HSBLC is
activated automatically in a low-light condition.
22
2. Use
or
button to set the bright level.
Exposure settings
AGC (Automatic Gain Control) setting
SHUTTER (Shutter Speed) setting
If the images are too dark, change the maximum [AGC]
value to make the images lighter.
1. Select [AGC] option on the [EXPOSURE] menu.
Select the desired shutter speed for camera exposure.
You can change the shutter speed to higher speed
to capture fast-moving subjects, though the image
becomes darker.
1. Select [SHUTTER] option on the [EXPOSURE]
menu.
2. Use
or
button to select a mode.
(OFFy LOWyMIDDLEyHIGH)
2. Use
or
button to set shutter speed.
(x512 to x2 y AUTOy OFF y A.FLK y
1/160 to 1/90 000)
23
Exposure settings
SENS-UP setting
If pictures are not clear due to darkness, use for
increase the sensitivity of picture.
1. Select [SENS-UP] option on the [EXPOSURE]
menu.
2. Use
or
to select [AUTO] option and press
button.
To setting the SENS-UP function, select the
[AUTO] on the [SHUTTER].
Note:
If you set to one of the SHUTTER options except
AUTO on the [SHUTTER] menu, the [SENS-UP]
setting is not available and [---] mark is displayed.
24
3. Select [SENS-UP LIMIT] option.
4. Use
or
to, x128).
button to set the SENS-UP limit (x2,
White Balance setting
Select the method by which the camera shifts its output
colors to compensate for the color of a light source.
1. Select [WHITE BALANCE] option on the [CAMERA
SETTING] menu.
2. Use
.
•
or
- When the scene contains mostly high color
temperature objects, such as a blue sky or
sunset.
- When the scene is dim.
•
AWCbPUSH: If you select the AWCbPUSH
mode, you will be able to set up the White
Balance automatically using
button.
•
MANUAL: You can set the white balance
options manually.
button to select a mode then press
ATW (Auto-Tracing White Balance): In this
mode, the color temperature range for the
proper white balance is approximately 1 700
to 11 000 K. Proper white balance may not be
obtained under the following conditions:
- COLOR TEMP: Use
select a function.
or
button to
- When the color temperature is out of the
1 700 to 11 000 K range.
25
White Balance setting
>
INDOOR: The color temperature
range for the proper white balance is
approximately 3 200 K.
>
OUTDOOR: The color temperature
range for the proper white balance is
approximately 5 100 K.
- RED: Set the desired red value.
(-100 to 100)
- BLUE: Set the desired blue value.
(-100 to 100)
26
Day/Night setting
1. Select [DAY/NIGHT] option on the [CAMERA
SETTING] menu.
- LEVEL: Use
or
button to select a
level.
(LOWyMIDDLEyHIGH)
2. Use
or
button to select mode for
DAY/NIGHT function.
•
- DWELL TIME: Use
or
button to
select a dwell time. (5, 10, 15, 30 or 60 s.)
AUTO: You will be able to change the
DAY/NIGHT mode automatically.
•
DAY: Color mode enabled.
Note:
•
NIGHT: Black-and-white mode enabled.
If you set the AGC to [OFF] the AUTO mode
of the DAY/NIGHT function is not available
and [---] mark is displayed.
27
Motion Detection setting
The motion detection detects the moving objects in the
scene by monitoring changes in brightness level. You
can select the level of sensitivity for motion detection
to 4 zone.
5. Use
or
to select an option then use
button to adjust the option.
1. Select [MOTION DET] option on the [CAMERA
SETTING] menu.
or
button to select a [ON] and press
2. Use
The MOTION DETECTION menu appears.
.
or
•
HEIGHT: Enlarge or decrease the vertical size
of the zone frame.
•
WIDTH: Enlarge or decrease the horizontal
size of the zone frame.
•
MOVE Y: Moves vertical position of the zone
frame.
•
MOVE X: Moves horizontal position of the
zone frame.
6. Use [SENSITIVITY] option to obtain the optimum
detection level.
3. Use
or
button to select a zone number
(AREA1 to AREA4) on the [ZONE NUMBER]
option.
or
button to set up the ON or OFF on
4. Use
the [ZONE STATE] option. If you set to ON, the
zone frame appears on the center of the monitor.
28
3D-DNR setting
1. Select [3D-DNR] option.
If pictures are not clear due to noise, use this function to reduce the noise of picture.
or
button to select a option.
2. Use
(OFFyLOWyMIDDLEyHIGH)
Notes:
•
If you set the AGC to [OFF] on the [EXPOSURE]
menu, the [3D-DNR] function is not available.
•
When you use this function, the afterimage may
occur.
29
Privacy Mask setting
This function is aiming at the protection of personal privacy, selecting a screen part black not to be displayed
in the screen. Up to 8 zones can be registered.
1. Select [PRIVACY] option on the [CAMERA
SETTING] menu.
or
button to select a [ON] and press
2. Use
The PRIVACY MASK menu appears.
3. Use
or
button to select a zone number
(AREA1 to AREA8) on the [MASK NUMBER]
option.
or
button to set up the ON or OFF on
4. Use
the [DISPLAY] option.
30
.
5. Use
or
button to select the color of the mask
zone box on the [COLOR] option.
or
to select an option then use
6. Use
button to adjust the option
or
•
HEIGHT: Enlarge or decrease the vertical size
of the mask zone box.
•
WIDTH: Enlarge or decrease the horizontal
size of the mask zone box.
•
MOVE Y: Moves vertical position of the mask
zone box.
•
MOVE X: Moves horizontal position of the
mask zone box.
Notes:
The parts with the registered mask numbers from
AREA1 to AREA4 have the same color. (So do the
parts with the numbers from AREA5 to AREA8). If you
change the mask color, the registered mask color will
be changed automatically with the same color for each
of group (AREA1 to 4, AREA5 to 8).
Special menu settings
Setting the D-ZOOM (Digital Zoom) level
D-EFFECT (Digital effect) setting
You can select the digital zoom level.
You can select the digital effect.
1. Select [D-ZOOM] option on the [SPECIAL] menu.
1. Select [D-EFFECT] option on the [SPECIAL] menu.
2. Use
or
button to select a [ON] then press
the DIGITAL ZOOM menu appears.
2. Use
or
button to select a option then use
3. Use
or
button to select a level.
- ZOOM: Use
or
button to enlarge the
screen.
- PAN: Use
or
button to move the screen.
(left or right)
- TILT: Use
or
button to move the screen.
(up or down)
or
button to select a digital effect.
•
V-FLIP: Flip the picture vertically.
•
MIRROR: Turn on the mirror effect.
•
ROTATE: Rotate the picture. (180°)
•
OFF: Turn off the digital effect.
31
Special menu settings
SHARPNESS setting
Stabilizer setting
Sharpens the image outline.
1. Select [SHARPNESS] option on the [SPECIAL]
menu.
The image stabilizer function minimizes the appearance
of shaky images caused by low-frequency vibration.
2. Use
or
button to change a adjust the option.
If you set the sharpness value to higher, the image
outline becomes sharp. If you set to lower value,
the image outline becomes dim.
32
This function is useful for outdoor surveillance.
Select [STABILIZER] option and set to ON or OFF.
Note:
If you set the [STABILIZER] to ON, the Digital zoom is
set to [x1.1] automatically.
Special menu settings
COLOR setting
You can switch the displayed picture to grayscale or
color.
The SYNC function is available only with AC power
source.
1. Select [SYNC] option on the [SPECIAL] menu.
1. Select [COLOR] option on the [SPECIAL] menu.
2. Use
2. Use
or
button to change a color effect.
•
ON: To display the picture with color.
•
OFF: To display the picture with grayscale.
Setting the SYNC (Synchronization)
or
button to select [INT] or [LL].
•
INT: Selects for using the internal synchronization.
•
LL (Line Lock): Selects for the operation of
multi cameras because it synchronizes the
camera phase by using the external signal
(AC Signal). A little phase deviation for some
sets may be aligned.
You can select internal sync (INT) mode or line-lock
(LINE) mode.
33
Special menu settings
User title setting
You can use the camera identification to assign a number and character to the camera (0 to 9, A to Z, a to z).
To disappear the user title, select [OFF].
1. Select [USER TITLE] option on the [SPECIAL]
screen.
or
button to select a [ON] then press
2. Use
. The USER TITLE menu appears.
3. Use ,
,
or number.
34
button to select a character
-
CLR: If you enter the wrong code, select CLR
then press .
-
,
or
button to move
POS: Use ,
position of USER TITLE on the screen.
-
END: Confirm your selection.
-
A(Blank): Insert a space at the cursor position.
-
A
or
/
: Moves cursor to left or right.
Special menu settings
Language setting
Select a language for setup menu and information
display.
35
Reset settings
1. Select [RESET] option.
2. Press
3. Use
or
to select option.
•
CAMERA REBOOT: Reboot the camera system.
•
FACTORY RESET: Clear certain settings and
information and return to factory default settings.
4. Press
36
button and the RESET menu appears.
to confirm your selection.
Specification
Model
LS501N
Signal System
NTSC
LS501P
PAL
Total/Effective Pixels
410 K/380 K
470 K/440 K
Image Device
6 mm Super HAD CCD
Lens
CS Mount (C Mount using adaptor ring)
Iris Control
DC / VIDEO
Synchronization System
Internal/Line Lock
Scanning Frequency (H)
15.734 kHz
Scanning Frequency (V)
59.94 Hz(VD)
Horizontal Resolution
S/N Ratio
Minimum
Illuminance
Day
Night
15.625 kHz
50 Hz(VD)
560 Lines (Color)
More than 50 dB (AGC Off)
0.0001 lx (Sens-Up X128, F1.2),
0.3 lx (Sens-Up Off, F1.2)
0.00005 lx (Sens-Up X128, F1.2),
0.03 lx (Sens-Up Off, F1.2)
37
Specification
Model
LS501N
LS501P
Video Output Signal
1.0 Vp-p Composite (75 Ω)
Atuo Gain Control
Low/Middle/High/Off
Day & Night
Electric Shutter Speed
White Balance
38
Day/Night/Auto
1/60 to 1/90 000
1/50 to 1/90 000
ATW / AWC->PUSH / MANUAL
Stabilizer (EIS)
OFF/ON
3D-DNR
Low/Middle/High/Off
Power Consumption
Less than 4.4 W
Power Source
DC 12 V / AC 24 V
Operation Temperature
-10 ºC to 50 ºC (Humidity: 0 % RH to 80 % RH)
Storage Temperature
-20 ºC to 60 ºC (Humidity: 0 % RH to 85 % RH)
Weight
380 g
Dimension (H x V x D)
68 x 61.5 x 123 mm
P/NO : MFL62034763
Download PDF

advertising