LG | LS923P-B | LG LS923P-B Owner’s Manual

Color Video Camera
User Manual
Model: LS921
LS923
Before installing, operating or adjusting
this product, please read this instruction
booklet carefully and completely.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if
an unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
•
A suitable conduit entries, knock-outs or glands shall
be provided in the cable entries of this product in the
end user.
•
•
Caution: Danger of explosion if battery is incorrectly
replaced. Replaced only with the same or equivalent
type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s
instructions.
Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall be
provided with brushings.
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
Caution: This installation should be made by a qualified
service person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
To disconnect power from mains, pull out the mains
cord plug. When installing the product, ensure that the
plug is easily accessible.
Warning: Do not install this equipment in a confined space
such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the
National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Warning: To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
Disposal of your old appliance
1.
When this crossed-out wheeled bin
symbol is attached to a product it means
the product is covered by the European
Directive 2002/96/EC.
2.
All electrical and electronic products
should be disposed of separately from
the municipal waste stream via designated collection facilities appointed by
the government or the local authorities.
3.
The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and
human health.
4.
For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you purchased the product.
This product is manufactured to comply
with EMC Directive 2004/108/EC and Low
Voltage Directive 2006/95/EC.
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : +31-036-547-8940)
Important Safety Instructions
1.
Read these instructions.
and the point where they exit from the apparatus.
2.
Keep these instructions.
3.
Heed all warnings.
11. Only use attachments/accessories specified by the
manufacturer.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
Cautions for Safe Operation
Power Supply
LS921P-B/ LS921N-B/ LS923P-B, LS923N-B:
use a cloth dampened with a small quantity of neutral
detergent then wipe dry.
•
This camera must always be operated a AC 24V or DC 12V
Certified/Listed, class 2 power supply only.
LS921P-C/ LS923P-C:
Avoid the use of volatile solvents such as thinners,
alcohol, benzene and insecticides.
They may damage the surface finish and/or impair the
operation of the camera.
This camera must always be operated a AC 230V.
Note:
Be careful of AC frequency when the camera is operated
with Line lock mode.
Operating and storage location
Avoid viewing a very bright object (such as light fittings)
during an extended period. Avoid operating or storing the
unit in the following locations.
Handling of the unit
•
Be careful not to spill water or other liquids on the unit. Be
cautions not to get combustible or metallic material inside
the body. If used with foreign matter inside, the camera is
liable to fail or to get cause of fire or electric shock.
Extremely hot or cold places (operating temperature 10°C ~ 50°C, however, we recommend that the unit be
used within a temperature range of 0°C ~ 45°C)
•
Damp or dust place
•
Places exposed to rain
•
Places subject to strong vibration
•
Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
•
Remove dust or dirt on the surface of the lens with a
blower.
•
Use a dry soft cloth to clean the body. If it is very dirty,
Contents
Features.................................................................. 8
Menu Operation.................................................. 22
Features Chart................................................................... 8
OSD Menu control buttons........................................22
Part Names and Functions.................................... 9
Connections......................................................... 12
Precautions......................................................................12
Connection Overview..................................................12
Connecting Display device........................................13
Connecting Power Source..........................................13
Connecting RS-485/RS-232C TTL Device..............14
Connecting Alarm Device...........................................15
Connecting Day&Night Switch.................................16
OSD Menu Overview....................................................23
General Operation.........................................................26
Camera Identification Settings.................................26
Exposure Settings..........................................................27
White Balance settings................................................30
Day/Night Setting..........................................................31
Motion Detection Setting...........................................32
3D-DNR Setting..............................................................33
Privacy Setting................................................................34
Special Menu Settings.................................................35
Mounting the Lens........................................................17
Reference............................................................. 41
Concerning Auto-Iris Lenses......................................19
RS-232C TTL/RS-485 Protocol (Optional)..............41
Flange-back Adjustment .........................................20
Specification....................................................................42
Mounting the camera..................................................21
Features
This Color Video Camera is designed for installation in an
video surveillance system.
LS923
This manual contains instructions on how to install and
manage the Color Video Camera in your video surveillance
system. Should you require any technical assistance, please
contact authorized service center.
LS921
High resolution and high sensitivity with a
1/3 inch Interline Color CCD.
•
600 TV lines of horizontal resolution.
•
Line Lock when using AC 24V.
•
Line Lock when using AC 230V.
(LS921P-C).
•
Automatically switch between DC 12V
and AC 24V.
•
High resolution and high sensitivity with a
1/3 inch Interline SUPER HAD CCD II.
•
650 TV lines of horizontal resolution.
•
Line Lock when using AC 24V.
•
Line Lock when using AC 230V.
(LS921P-C).
Features Chart
•
Automatically switch between DC 12V
and AC 24V.
This table shows the differences between the models.
Use LS921P-B is used for the description, operation and
details provided in this operating guide.
Models
•
WDR
Sens-up
Day & Night
Stabilizer
LS921
No
Yes
Filter change
Yes
LS923
Yes
Yes
Filter change
No
Part Names and Functions
a
b
cd e
f
c Flange-back adjustment lever
d Lens iris output connector (LENS)
This 4- pin connector is used to send the Iris control
signal and power supply to an auto-iris type lens.
e Setup menu control buttons
Use these buttons to set the menu options.
f ALC Lens Setting Switch
a Lens mount cap
•
DC: When you attach an Auto Iris lens requiring
the DC control signal, please put this switch in
the DC position.
•
ELC: When you attach a manual or fixed lens,
please put this switch in the ELC position.
•
VIDEO: When you attach an Auto Iris lens requiring the video control signal, please put this
switch in the VIDEO position.
The lens mount of the camera is covered using a cap
to protect it. Remove the lens cap covering the lens.
b Camera installation bracket
The bracket can be fixed at the top or bottom of the
camera.
Part Names and Functions
LS921P-B/ LS921N-B/ LS923P-B/ LS923N-B
g
h
ij k
g Power input terminal
Supplies AC 24V or DC 12V from an external power
source.
h External Device Connectors
•
D&N
Connect the external switch to set the D&N function manually.
•
ALARM (Alarm Output Terminal)
Connect to the alarm input of an external device.
•
COM (COMMUNICATION)
Connect to an external controller of RS-232C TTL/
RS-485(optional) format.
i Power indicator
Lights when the camera is powered.
j GND
k Video output connector (BNC type)
Supplies analog video signal (composite) to the connected device such as a DVR or monitor.
10
Part Names and Functions
LS921P-C/ LS923P-C
g
h
ij k
g Power cable
h External Device Connectors
•
D&N
Connect the external switch to set the D&N function manually.
•
ALARM (Alarm Output Terminal)
Connect to the alarm input of an external device.
•
COM (COMMUNICATION)
Connect to an external controller of RS-232C TTL/
RS-485(optional) format.
i Power indicator
Lights when the camera is powered.
j GND
k Video output connector (BNC type)
Supplies analog video signal (composite) to the connected device such as a DVR or monitor.
11
Connections
Precautions
•
Be sure to switch off the unit before installation and connection.
•
A qualified service person, complying with all applicable codes, should perform all required hardware installation.
•
Do not expose the power and connection cable to moisture, which may cause damage to the unit.
Connection Overview
RS-232C TTL/
RS-485 Unit
External D&N
Switch
12
Connections
Connecting Display device
The video signal connection between the camera and the
monitor.
Connecting Power Source
LS921P-B/ LS921N-B/ LS923P-B, LS923N-B
Connect power, using the method listed below:
1. Remove the insulation on the power cable as
illustrated. (a)
2. Attach the terminal tips. (b)
3. Connect to the DC 12 V / AC 24 V UL Listed, Class
2 Power Supply only on the unit.
13
Connections
LS921P-C/ LS923P-C
Insert the plug of the power cord into a wall outlet. The
POWER indicator will light.
Connecting RS-485/RS-232C TTL
Device
Use these ports to connect an external device of RS-232C
TTL/ RS-485 format.
Tx(+)
RS-485 Unit
Rx(-)
GND
RS-232C TTL
Tx(+)
Rx(-)
14
Connections
Connecting Alarm Device
Contact Ratings
Alarm terminals are used to connect the alarm (relay)
devices such as sensors, door switches, etc.
•
Maximum load current is
±130mA.
Connect the alarm (relay) device to the alarm (relay) output
terminal. Alarm signal outputs at an event occurrence.
•
Do not connect any system or device that has
over 40 Vp-p (DC 30 V)
bias voltage on the contact terminal.
ALARM
COM
Equivalent
Diagram
Note:
Alarm (Relay)
Device
Use a relay unit if the voltage or current of the connected device exceeds the ratings.
15
Connections
Connecting Day&Night Switch
Connect the external D&N switch to the D&N terminal.
Open
Open
External D&N
Switch
External S/W
External S/W
Night function
When you close the external switch, the D&N function
is set to night mode.
Day function
When you open the external switch, the D&N function
is set to Day mode.
Close
Close
External S/W
External S/W
16
Connections
Note:
opening, then turn the lens slowly to install it.
If you use the external D&N function, you should set
the DAY/NIGHT option to EXT on the setup menu.
2-2. C mount type lens
To allow for flange- back adjustment, install the
C-mount adaptor (option) on the lens mount,
then carefully align the lens mount with the camera opening and turn the lens slowly to install it.
Mounting the Lens
1. Remove the lens mount cap from the camera.
2-1
2-2
2. Install the auto-iris lens.
2-1. CS mount type lens
Carefully align the lens mount with the camera
3.
Connect the lens plug to the lens iris output connector (LENS) on the side of the camera.
When using lenses from other makers, the plug shape
may not correspond to the terminal on the camera.
17
Connections
In such a case, remove the original plug and using a
soldering iron, connect a lens iris plug according to
the diagram. (Refer to next page.)
lens iris output connector
Rewire the lens iris plug
1. Cut off the plug of the lens cable, cut off approximately 8mm of the insulation, and then strip
approximately 2mm of the ends of the cable
sheaths.
Pin layout for the lens iris output connector.
8mm
2mm
2. Solder the ends of the cable wires to the ends of
the pins, and then attach the cover of the lens iris
plug.
18
No.
DC type lenses
VIDEO type lenses
1
Damping -
Vcc (+9V)
2
Damping +
Not used
3
Drive +
Video
4
Drive -
Ground
Connections
Concerning Auto-Iris Lenses
DC type auto-iris lens
ELC type auto-iris lens
Use a manual or fixed iris lens (Set the ALC Lens
Setting Switch to the ELC position.)
A lens without driver circuit that operates only on a DC
power source. In general, this type of lens is referred to
as DC type coil lens. (Set the ALC Lens Setting Switch
to the DC position.)
CAUTION:
Depending on the type of lens used, the lens may not
perform properly.
VIDEO type auto-iris lens
A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens
is referred to as EE amplifier type lens. ALC and LEVEL
volume level controls are available on the lens for iris
adjustments. (Set the ALC Lens Setting Switch to the
VIDEO position.)
CAUTION:
19
Connections
Be cautions not to use Auto Iris Lens with over 35mA.
Note:
The object may be out of focus when using a source of
near-infrared light than using the visible light.
Flange-back Adjustment
The adjustment is required only when a lens without focusadjusting mechanism is mounted, or when a lens with
adjusting mechanism is mounted and focus that is more
accurate is needed.
1. Loosen the flange-back fixing lever.
2. Up and down the flange-back adjusting lever to
obtain a focused point while watching the monitor
screen.
3. Tighten the flange-back fixing lever.
20
Connections
Mounting the camera
The mounting bracket can be secured on either the top or
bottom of the camera. Use the same set of screws to attach
the mounting bracket on the camera.
Note:
If using a camera mounting bracket, select a location that
is strong enough to bear the full weight of the camera
and the mounting bracket for long periods, and install the
camera and mounting bracket securely.
21
Menu Operation
OSD Menu control buttons
BUTTON
Description
UP button
Used to move upper direction on the
menu screen. Use this button to select
an item or adjust the parameters.
DOWN button
Used to move lower direction on the
menu screen. Use this button to select
an item or adjust the parameters.
This camera utilizes an on-screen user MENU. To set items
on the menu, use the following buttons.
RIGHT button
LEFT button
Moves the cursor to the right. Used to
increment the value selected in the
menu. The parameter changes each
time this button is pressed.
Moves the cursor to the left. Used to
decrement the value selected in the
menu. The parameter changes each
time this button is pressed.
Executes selections and displays a submenu for an item with the mark.
SET button
22
Menu Operation
OSD Menu Overview
Main Menu
Sub Menu
AWC b PUSH
WHITE BAL
Main Menu
Sub Menu
Contents
CAMERA ID
-
OFF, 1~255
EXPOSURE
ALC/ ELC
MANUAL
BACKLIGHT
OFF/BLC/HSBLC
BRIGHTNESS
0~100
AGC
OFF/LOW/MIDDLE/
HIGH
SHUTTER
X512, ~, x2, AUTO,
OFF, A.FLK, 1/160,
~, 1/90000
SENS-UP
EXIT
OFF
Contents
ATW
The following table shows the list of menu items and options. You can adapt the camera to your requirements by
setting up the respective items in these menus.
COLOR TEMP
INDOOR,
OUTDOOR
RED
-100 ~ 100
BLUE
-100 ~ 100
EXIT
RET/TOP/END
LEVEL
AUTO
DWELL TIME
EXIT
DAY/NIGHT
LOW/ MIDDLE/
HIGH
5, 10, 15, 30,
60 SEC
RET/TOP/END
EXT
DAY
NIGHT
AUTO
RET/TOP/END
23
Menu Operation
Main Menu
MOTION DET
Sub Menu
ON
Contents
24
Sub Menu
Contents
AREA1~4
ZONE STATE
ON/OFF
MASK NUMBER
AREA1~AREA8
HEIGHT
12~100
DISPLAY
ON/OFF
WIDTH
16~100
MOVE Y
6~94
COLOR
GRAY, WHITE,
BLACK,
MOVE X
8~92
SENSITIVITY
0~100
EXIT
RET/TOP/END
OFF
3D-DNR
Main Menu
ZONE NUMBER
OFF
-
LOW
-
MIDDLE
-
HIGH
-
OFF
PRIVACY
ON
-
HEIGHT
4~100
WIDTH
4~100
MOVE Y
2~98
MOVE X
2~98
EXIT
RET/TOP/END
Menu Operation
Main Menu
Sub Menu
Contents
Main Menu
OFF
D-ZOOM
D-EFFECT
SPECIAL
ZOOM
PAN
TILT
EXIT
ON
OFF/ V-FLIP/ MIRROR/ ROTATE
SHARPNESS
0~68
STABILIZER
OFF/ ON
COLOR
OFF/ ON
SYNC
INT / LL
USER TITLE
OFF/ ON
LANGUAGE
English
(The supported language can be different depending on the model.)
EXIT
RET/TOP/END
Sub Menu
Contents
CAMERA REBOOT
-
FACTORY RESET
PROTOCOL
RESET
COMMUNICATION
BAUD RATE
SAVE&REBOOT
EXIT
EXIT
EXIT
RET/TOP/END
-
-
25
Menu Operation
General Operation
1.
•
•
Press [SET] button.
The setup menu screen appears on the monitor.
TOP: Return to the CAMERA SETTING menu
screen.
END: Exit the setup menu.
Camera Identification Settings
You can use the camera identification (CAMERA ID) to
assign a number to the camera.
2.
Use [UP] or [DOWN] button to select an option then
press [SET] button.
Submenu appears on the monitor.
3.
Use [UP] or [DOWN] button to select a submenu
option.
4.
Use [LEFT] or [RIGHT] button to select a value.
5.
Select [EXIT] option then press [SET] to exit the setup
menu. In the submenu, use [UP] or [DOWN] button to
select the [EXIT] then use [LEFT] or [RIGHT] button to
select a mode and press [SET] to exit the setup menu.
•
26
RET: Return to the previous.
1.
Select [CAMERA ID] option on the [CAMERA SETTING]
menu.
2.
Use [LEFT] or [RIGHT] to select a CAMERA ID (OFF, 1255).
Menu Operation
Exposure Settings
You can set the exposure options using the EXPOSURE
menu.
1.
Select [EXPOSURE] option on the [CAMERA SETTING]
menu.
2.
Use [LEFT] or [RIGHT] button to select a mode
(ALCy ELC).
3.
Press [SET] button and the EXPOSURE menu appears.
BACKLIGHT setting
Use BACKLIGHT option to view the object clearly in backlight conditions.
1.
Select [BACKLIGHT] option.
2.
Use [LEFT] or [RIGHT] button to select a mode then
press [SET].
•
WDR (For LS923 model only): WDR (Wide dynamic
range) feature can be very helpful to cope with
very challenging lighting conditions. It is capable
of capturing both of the dark part and bright
part and combining the differences into a scene
to generate a highly realistic image as original
scene. Set the WDR limit.
27
Menu Operation
•
•
> WDR LIMIT: LOW y MIDDLE y HIGH
BLC: Camera's backlight compensation feature
helps alleviate issues of visibility in high contrast
areas. Set the BLC limit.
> BLC LIMIT: LOW y MIDDLE y HIGH
HSBLC: Use for masking brightness of the specific
area to view the subject more clearly. The HSBLC
mode is automatically activated only in low luminance scene.
>
>
>
>
28
AREA SETTING: Use [LEFT] or [RIGHT] button to select a area then use [UP] or [DOWN]
button to select a ON or OFF. Press [SET] to
exit the Area setting menu.
GRAY SCALE: Use [LEFT] or [RIGHT] button
to select a gray scale.
(GRAYyD.GRAYyBLACK).
USER SCALE: Use [LEFT] or [RIGHT] button
to select a bright level.(5 level)
MASK: Use [LEFT] or [RIGHT] button to
select [ON] or [OFF].
If you set the MASK to ON, the mask function
is activate only when the HSBLC is automati-
•
cally activated in low luminance scene.
OFF: Not used.
Brightness setting
You can increase the brightness of the darkened video. If
you set the brightness to lower value, the image is darkened. If you set the brightness to higher value, the image
gets bright.
1.
Select [BRIGHTNESS] option.
2.
Use [LEFT] or [RIGHT] button to set the bright level.
Menu Operation
AGC (Automatic Gain Control) setting
SHUTTER (Shutter Speed) setting
If the images are too dark, change the maximum [AGC]
value to make the images brighter.
Select the desired shutter speed for camera exposure. You
can change the shutter speed to higher speed to capture
fast-moving subjects, though the image becomes darker.
1.
Select [AGC] option.
2.
Use [LEFT] or [RIGHT] button to select a mode.
(OFFy LOWyMIDDLEyHIGH)
1.
Select [SHUTTER] option.
2.
Use [LEFT] or [RIGHT] button to set shutter speed.
(AUTOy OFF y A.FLK y 1/160 ~ 1/90000 y
x512~x2)
29
Menu Operation
SENS-UP setting
If pictures are not clear due to darkness, this SENS-UP
operation would increase the sensitivity of picture.
•
OFF: Not used.
Note:
If you set to one of the SHUTTER options except AUTO on
the [SHUTTER] menu or [AGC] to [OFF], the [SENS-UP] setting is not available and [---] mark is displayed.
White Balance settings
1.
Use [UP] or [DOWN] button to select [SENS-UP]
option.
2.
Use [LEFT] or [RIGHT] button to select mode.
•
AUTO: Adjust the sensitivity of the picture automatically.
>
>
30
SENS-UP LIMIT: Use [LEFT] or [RIGHT] button to set the SENS-UP limit.
EXIT: Select a mode and press [SET] to exit
the menu.
Select the method by which the camera shifts its output
colors to compensate for the color of a light source.
Menu Operation
1.
Select [WHITE BAL] option.
2.
Use [LEFT] or [RIGHT] button to select a mode then
press [SET].
•
ATW (Auto-Tracing White Balance): The color
temperature range for the proper white balance
is approximately 1,700 - 11,000ºK. Proper white
balance may not be obtained under the following
conditions:
>
>
>
The color temperature is out of the 1,700
- 11,000 ºK range.
When the scene contains mostly high color
temperature objects, such as a blue sky or
sunset.
When the scene is dim.
•
AWCbPUSH: If you select the AWCbPUSH mode,
you will be able to set up the White Balance automatically using [SET] button.
•
MANUAL: You can set the white balance options
manually.
>
-
>
>
INDOOR: The color temperature range
for the proper white balance is approximately 3,200°K.
OUTDOOR: The color temperature range
for the proper white balance is approximately 5,100°K.
RED: Obtains the optimum amount of red
gain.
BLUE: Obtains the optimum amount of blue
gain.
Day/Night Setting
COLOR TEMP: Use [LEFT] or [RIGHT] button
to select a function.
31
Menu Operation
1.
Select [DAY/NIGHT] option.
2.
Use [LEFT] or [RIGHT] button to select mode for day/
night function.
•
AUTO: You will be able to change the Day/Night
mode automatically.
Note:
If you set the AGC to [OFF] or the SHUTTER is set
to one of the SHUTTER options except AUTO on
the [EXPOSURE] menu, the AUTO mode of the
DAY/NIGHT function is not available and [---]
mark is displayed.
LEVEL: Use [LEFT] or [RIGHT] button to
select a level.
(LOWyMIDDLEyHIGH)
> DWELL TIME: Use [LEFT] or [RIGHT] button
to select a dwell time. (5, 10, 15, 30 or 60
SEC)
EXT : Switches between color picture and blackand-white picture when an external day/night
switching signal is received.
•
NIGHT: Black-and-white mode enabled.
Motion Detection Setting
The motion detection detects the moving objects in the
scene by monitoring changes in brightness level. You can
select the level of sensitivity for motion detection to 4 zone.
>
•
•
32
DAY: Color mode enabled.
1.
Select [MOTION DET] option.
2.
Use [LEFT] or [RIGHT] button to select a [ON] and
press [SET].
The MOTION DETECTION menu appears.
Menu Operation
3.
Use [LEFT] or [RIGHT] button to select a zone number
(AREA1 ~ AREA4) on the [ZONE NUMBER].
4.
Use [LEFT] or [RIGHT] button to set up the ON or OFF
on the ZONE STATE.
5.
Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
6.
•
HEIGHT: Enlarge or decrease the vertical size of
the mask.
•
WIDTH: Enlarge or decrease the horizontal size of
the mask.
•
MOVE Y: Moves vertical position of the mask.
•
MOVE X: Moves horizontal position of the mask.
Use [SENSITIVITY] option to obtain the optimum
detection level.
3D-DNR Setting
1.
Select [3D-DNR] option.
If pictures are not clear due to brightness, this option
would reduce the noise of picture.
2.
Use [LEFT] or [RIGHT] button to select a option.
(OFFyLOWyMIDDLEyHIGH)
Notes:
•
If you set the AGC to [OFF] on the [EXPOSURE] menu,
the [3D-DNR] function is not available and [---] mark
is displayed.
•
When you use this function, the afterimage may occur.
33
Menu Operation
Privacy Setting
This function is aiming at the protection of personal privacy, selecting a screen part black not to be displayed in
the screen. Up to 8 zones can be registered.
WHITE or BLACK on the COLOR option.
6.
Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
•
HEIGHT: Enlarge or decrease the vertical size of
the mask.
•
WIDTH: Enlarge or decrease the horizontal size of
the mask.
•
MOVE Y: Moves vertical position of the mask.
•
MOVE X: Moves horizontal position of the mask.
Note:
1.
Select [PRIVACY] option.
2.
Use [LEFT] or [RIGHT] button to select a [ON] and
press [SET]. The PRIVACY SETUP menu appears.
3.
Use [LEFT] or [RIGHT] button to select a mask (AREA1
~ AREA8) on the [MASK NUMBER].
4.
Use [LEFT] or [RIGHT] button to set up the ON or OFF
on the DISPLAY option.
5.
Use [LEFT] or [RIGHT] button to set up the GRAY,
34
The parts with the registered mask numbers from AREA1 to
AREA4 have the same color. (So do the parts with the numbers from AREA5 to AREA8). If you change the mask color,
the registered mask color will be changed automatically
with the same color for each of group (AREA1~4, AREA5~8).
Menu Operation
Special Menu Settings
This menu lets you adjust and set up D-ZOOM, D-EFFECT,
SHARPNESS, STABILIZER, COLOR, SYNC, USER TITLE,
LANGUAGE function by yourself in the SPECIAL menu.
1.
Select [SPECIAL] option.
2.
Press [SET] button and the SPECIAL menu appears.
Setting the D-ZOOM (Digital Zoom ) level
You can select the digital zoom level.
1.
Select [D-ZOOM] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to select a [ON] then
press [SET] the DIGITAL ZOOM menu appears. When
you set to ON, the displayed image can be shaking.
3.
Use [UP] or [DOWN] to select a option then use
[LEFT] or [RIGHT] button to select a level.
•
ZOOM: Use [LEFT] or [RIGHT] button to enlarge
the screen.
•
PAN: Use [LEFT] or [RIGHT] button to move the
screen. (left or right)
•
TILT: Use [LEFT] or [RIGHT] button to move the
screen. (up or down)
35
Menu Operation
Setting the D-EFFECT (Digital effect)
Setting the SHARPNESS effect
You can select the digital effect.
The degree to which the boundary of the two portions is
clearly distinguished.
1.
2.
36
Select [D-EFFECT] option on the [SPECIAL] menu.
Use [LEFT] or [RIGHT] button to select a digital effect.
•
V-FLIP: Flip the picture vertically.
•
MIRROR: Turn on the mirror effect.
•
ROTATE: Rotate the picture. (180°)
•
OFF: Turn off the digital effect.
1.
Select [SHARPNESS] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to change a adjust
the option. If you set the sharpness value to higher,
the image outline becomes sharp. If you set to lower
value, the image outline becomes dim.
Menu Operation
Stabilizer setting
Setting the COLOR effect
The image stabilizer function minimizes the appearance of
shaky images caused by low-frequency vibration.
You can switch the displayed picture to gray scale or color.
This function is useful for outdoor surveillance.
Select [STABILIZER] option and set to ON or OFF.
1.
2.
Note:
Select [COLOR] option on the [SPECIAL] menu.
Use [LEFT] or [RIGHT] button to change a color effect.
•
ON: To display the picture with color.
•
OFF: To display the picture with grayscale.
If you set the [STABILIZER] to ON, the Digital zoom is set to
[x1.1] automatically.
37
Menu Operation
Setting the SYNC (Synchronization)
The SYNC function is available only with AC power source.
1.
Select [SYNC] option on the [SPECIAL] menu.
2.
Use [LEFT] or [RIGHT] button to select [INT] or [LL]
(Line Lock).
•
INT: Selects for using the internal synchronization.
•
LL (Line Lock): Selects for the operation of multi
cameras because it synchronizes the camera
phase by using the external signal (AC power
signal).
2-1. Select [LL] mode and press [SET].
2-2. Select a desired phase using the [LEFT] or
[RIGHT] button.
Note:
When you use the DC 12V power, the [SYNC]
option is fixed to [INT] mode only.
Setting the USER TITLE
38
You can use the camera identification to assign a number
and character to the camera (0 - 9, A-Z, a-z).
The USER TITLE is displayed on the upper left of the screen.
To disappear the user title, select [OFF].
1.
Select [USER TITLE] option on the [SPECIAL] screen.
2.
Use [LEFT] or [RIGHT] button to select a [ON] then
Menu Operation
Language Setting
press [SET]. The USER TITLE menu appears.
Select the viewer language for the camera setup menu and
OSD information display.
A
3.
Use [UP], [DOWN], [LEFT] or [RIGHT] button to select
a character or number then press [SET] button.
•
CLR: Clear all entered characters and numbers.
•
POS: Move the USER TITLE position on the screen
using the arrow buttons.
1.
Select [LANGUAGE] option on the [SPECIAL] screen.
•
END: Confirm your selection or exit the setting.
2.
Press [LEFT] or [RIGHT] button to select a language.
A (Blank): Inserts a space at the cursor position.
�
/
: Moves cursor to left or right.
39
Menu Operation
Reset Settings
•
CAMERA REBOOT: To reboot the camera system.
•
FACTORY RESET: To reset the camera setting to
factory setting, select [FACTORY RESET] option.
•
COMMUNICATION (For LS921 model only)
>
1.
Select [RESET] option.
2.
Press [SET] button and the RESET menu appears.
3.
Use [UP] or [DOWN] to select option.
40
4.
PROTOCOL: Select a protocol for RS-232C
TTL/RS-485 communication.
> BAUD RATE: Set the speed of communication between the camera and the RS-232C
TTL/RS-485 unit.
> SAVE&REBOOT: To confirm the communication settings.
Press [SET] button to confirm your selection.
Reference
RS-232C TTL/RS-485 Protocol (Optional)
Data Communication Format
•
Data Length: 1 Byte (8 Bit)
•
Start/Stop Bit: 1 Bit
•
Parity Bit: None
•
Baud rate: 9,600 bps
BYTE2
0xE5
0x86
BYTE3
C.S. = 0xC5 +0x5F +0x02 +0x00 +0x0A = 0x0130
therefore, C.S. = 0x30
Commands
Function
OSD Menu ON/OFF
Format
BYTE1
ex) In case of transmission, 0xC5, 0x5F, 0x02, 0x00,
0x0A”
BYTE4
BYTE5
BYTE6
Camera CODE1
ID
CODE2
*C.S.
*C.S. = Check Sum
•
The data of total 6 bytes is transmitted from the external RS-485 device to the camera.
•
BYTE 6 : The value of Check Sum from ‘BYTE 1 ’ to
‘BYTE 5 ’.
Command
E5, 86, ID, 41, 02, C.S.
LEFT Button
E5, 86, ID, 12, 80, C.S.
Right Button
E5, 86, ID, 12, 90, C.S.
Up Button
E5, 86, ID, 11, 80, C.S.
Down Button
E5, 86, ID, 11, 90, C.S.
Menu Button
E5, 86, ID, 41, 01, C.S.
41
Reference
Specification
ITEM
Signal System
Total/Effective Pixels
Pick-up Device
LS921N-B
LS921P-B
LS921P-C
NTSC
PAL
PAL
410K / 380K
470K / 440K
470K / 440K
Pixels
Pixels
Pixels
1/3” Interline SUPER HAD CCD II
Lens
LS923N-B
LS923P-B
LS923P-C
NTSC
PAL
PAL
410K / 380K
470K / 440K
470K / 440K
Pixels
Pixels
Pixels
1/3" Interline Color CCD
C/CS Mount Lens
Signal Process
XDI-S2
XDI-A
Synchronization System
Internal / Line Lock
Scanning Frequency (H)
15.734KHz
15.625KHz
15.625KHz
15.734KHz
15.625KHz
15.625KHz
Scanning Frequency (V)
59.94 Hz (VD)
50 Hz (VD)
50 Hz (VD)
59.94 Hz (VD)
50 Hz (VD)
50 Hz (VD)
Resolution
More than 650 TV Lines
More than 600 TV Lines
S/N Ratio
More than 52dB (AGC Off, F1.2)
More than 52 dB (AGC Off, F 1.0)
Video Output Signal
42
1Vp-p Composite (75 ohm)
Reference
ITEM
Minimum
Illumination
LS921N-B
LS921P-B
LS921P-C
LS923N-B
LS923P-B
LS923P-C
Day
0.0001 Lux (Sens-up Auto, F1.2)
(0.05 Lux: Sens-Up Off, F1.2)
0.0003 Lux (Sens-Up Auto, F1.2)
(0.1 Lux : Sens-Up Off, F1.2)
Night
0.00001 Lux (Sens-up Auto, F1.2)
(0.0005 Lux: Sens-Up Off, F1.2)
0.00003 Lux (Sens-Up Auto, F1.2)
(0.01 Lux : Sens-Up Off, F1.2)
Iris Control
DC/ELC/VIDEO
Gain Control
OFF/LOW/MIDDLE/HIGH
Exposure
Shutter Speed
ALC/ELC
1/60 ~
1/90,000
1/50 ~ 1/90,000
ATW/ AWCbPUSH /MANUAL
White Balance
Power Source
1/60 ~
1/90,000
1/50 ~ 1/90,000
DC 12V / AC24V
AC 230V
Power Consumption
DC 12V / AC24V
Operation Temperature
-10˚C ~ 50˚C (Humidity: 0%RH~80%RH)
Storage Temperature
-20˚C ~ 60˚C (Humidity: 0%RH~85%RH)
Weight
Dimension (W x H x D)
AC 230V
4.4 W
415g
485g
415g
485g
67.4 x 61.5 x 134 mm
43
P/NO: MFL62723708
Download PDF

advertising