LG | LT703P-B | Owner's Manual | LG LT703P-B Owner’s Manual

LG LT703P-B Owner’s Manual
Dome Camera
Owner’s Manual
MODEL: LT703
Before installing and using the camera, please read this owner's
manual carefully and retain for future reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
FCC WARNING : This equipment may generate or
use radio frequency energy. Changes or modifications
to this equipment may cause harmful interference
unless the modifications are expressly approved in the
instruction manual. The user could lose the authority
to operate this equipment if an unauthorized change
or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
•
A suitable conduit entries, knock-outs or glands
shall be provided in the cable entries of this product in the end user.
•
Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer ’s instructions.
•
Holes in metal,,through which insulated wires
pass,shall have smooth well rounded surfaces or
shall be provided with brushings.
Warning: Do not install this equipment in a confined
space such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with
the National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic
environment this product may cause radio interference in which case the user may be required to take
adequate measures.
Warning: To reduce a risk of fire or electric shock, do
not expose this product to rain or moisture.
Caution: This installation should be made by a qualified service person and should conform to all local
codes.
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by
the European Directive 2002/96/
EC.
2. All electrical and electronic products should be disposed of separately from the municipal waste
stream via designated collection
facilities appointed by the government or the local authorities.
3. The correct disposal of your old
appliance will help prevent potential negative consequences for the
environment and human health.
4. For more detailed information about
disposal of your old appliance,
please contact your city office,
waste disposal service or the shop
where you purchased the product.
This product is manufactured
to comply with EMC Directive
2004/108/EC and Low Voltage
Directive 2006/95/EC.
European representative:
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere, The
Netherlands
(Tel : +31-036-547-8940)
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install
in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete
outlet.
10.Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11.Only use attachments/accessories specified by
the manufacturer.
12.Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
13.Unplug this apparatus during lightning storms
or when unused for long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as powersupply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
Contents
Menu navigation..................................................22
General Operation...............................................23
Focus setting.......................................................23
Introduction................................................................5
About Dome Camera.............................................5
Features.................................................................5
Safety Precautions.................................................6
Identification of Camera.........................................7
Installation..................................................................8
Precautions............................................................8
Removing the Protection Tape............................... 8
Mounting the Camera............................................9
Dipswitch Setting................................................. 11
Alarm Output Mode Setting.................................12
Camera ID Setting...............................................12
Connection...............................................................15
Precautions..........................................................15
Connection preview.............................................15
RS-485 connection..............................................15
Connecting monitor..............................................15
Connecting power source....................................15
ALARM IN connections........................................16
ALARM OUT connections....................................18
Connecting LKD1000 controller........................... 19
System Connection..............................................20
Operation..................................................................21
Setup Menu Overview.........................................21
Exposure settings................................................25
White Balance setting..........................................26
Day/Night setting.................................................27
Motion Detection setting......................................27
Privacy Mask setting............................................28
3D-DNR setting....................................................28
Special menu settings..........................................28
Language setting.................................................30
Reset settings......................................................30
Reference.................................................................31
Specifications.......................................................31
About Dome Camera
The dome cameras are designed for installation in an
indoor or outdoor video surveillance system.
The camera incorporates the digital signal processor,
pan/tilt mechanism, x27 zoom lens and RS-485 communication interface in a compact outdoor enclosure.
Features
m High Sensitivity Support
The camera provides the high quality picture with
4.5 mm EX-view HAD CCD.
m Preset Position
Preset position is the function to register camera
monitoring positions (preset positions). By using
LKD1000 controller, you can register presets with
position number. Maximum 128 Preset Position
are available. By entering the position numbers,
you can move cameras to the preset positions.
The moving speed and holding time are adjustable.
m Preset Tour
Preset Tour is the function to go through all the
registered camera monitoring positions (preset
positions).
m Preset Group Tour
A preset tour is composed of a group of preset
positions that the operator can program to be
linked together in a sequence. A preset group
should have a maximum of 8 preset positions.
m Pattern recording function
A routine of manual operations can be stored and
reproduced repetedly. The Pan, Tilt and Zoom controls are available for pattern recording.
Note:
The available total time of pattern differs depending on camera’s operation. When the pattern
recording is full, the pattern recording will automatically stop.
Introduction
Introduction
m Privacy Mask
Privacy zone feature enables users to veil unwanted zones. This setting is used for masking unwanted zones, hiding them from display on the monitor
screen. Up to 8 zones can be registered.
m Auto Pan
The camera has an Auto Pan function that enables
to keep surveillance on every detail occurring
around the specific area, which is preset to watch
in advance.
The camera can pan among the maximum 8
points you will set. The moving speed and holding
time are adjustable.
m Auto Flip
When the camera is operated to tilt through the
90°, it can be watched the opposite side of the
locations by Auto Flip of a 180° horizontally.
m Optical Zoom
The optical zoom range is 1x to 27x.
m Digital Zoom
Digital zoom enhances the systems zoom range
to 12 times beyond the 27x optical zoom limit. By
utilizing the digital zoom function, the total system
zoom range increases further from 27x (1x digital
zoom) to 324x (12x digital zoom)
m Sensor Linkage
The camera is capable of capturing a subject by
the focus of camera moving promptly toward the
subject at the rate of 120°/s when the camera
works with a detector (magnetic, beam, infrared
rays), and a subject moving within a detection area
is captured by a detector.
m Alarm In function (8 channels)
Alarm input signals are supplied from external
devices through the ALARM IN connector to activate 'go to preset' function.
m Alarm Out function (4 channels)
When alarm inputs are supplied via the alarm
input connector on the camera, the camera sends
output signals via the alarm output connector on
the camera.
m Controls by General Controller
This camera can be controlled by RS-485.
Especially the camera has an excellent cost-saving effect because it can be controlled by the general RX point of contact signal.
m Connects with the maximum 256 cameras
This camera can be utilized after being connected
with maximum 256 cameras.
Therefore, it is capable of performing an excellent
job in the large buildings or department stores.
The lens may become cloudy due to condensation
if the camera is used under the following conditions.
•
Rapid temperature fluctuation by switching an
air conditioner on and off.
m Day & Night Function
This camera can be selected Color or Black &
White. You can set Color in the daytime and Black
& White at night due to the low illumination. (Filter
Conversion type)
•
Rapid temperature fluctuation due to frequent
door opening and closing.
•
Use in an environment where eyeglasses
become foggy.
•
Use in a room filled with cigarette smoke or
dust.
m DSS (Digital Slow Shutter) function
It is possible to highly sensitive surveillance
because of DSS(Digital Slow Shutter) function.
m WDR (Wide Dynamic Range) function
The camera can be best condition to watch easily
inside or outside in the strong back light.
m Power Supply
This camera must always be operated a AC 24 V
Certified/Listed, class 2 power supply only.
Safety Precautions
m Do not attempt to disassemble the camera
To prevent electric shock,do not remove screws or
covers. There are no user serviceable parts inside.
Ask a qualified service personnel for servicing.
m Avoid the camera with direct sunlight
Do not aim the camera at bright objects.Whether
the camera is in use or not, never face it with
direct sunlight or other extremely bright objects.
Otherwise blooming or smear may be caused.
m Handle the camera with care
Do not abuse the camera. Avoid striking, shaking,
etc. The camera could be damaged by improper
handling or storage.
m Do not use strong solvents or detergents
Use a dry cloth to the camera when it is dirty. If
it is hard to remove the dirt on the camera, use a
mild detergent and wipe it gently.
m Do not install this camera upside down
This camera is designed for mounting on the ceiling or wall.If you install this camera upside down,
for example, mounted on the floor, it may cause
malfunction.
m Do not use the camera in such places as
shown below.
If the lens becomes cloudy due to condensation,
remove the dome cover and wipe all moist surfaces with a soft cloth.
m Before operating, please check proper temperature, humidity and power source ratings.
Use the camera under conditions where temperature is between -10 to 50 °C and humidity is below
80%. The input power source is AC 24 V.
m Consumables
Parts having contacts such as the lens-drive
motors,cooling fan built inside the camera are
subject to wear with time. About replacement and
maintenance of such parts,please ask the nearest
service center.
Identification of Camera
aDome camera body
f
g
“A”
h
i
j
k
Introduction
bCamera mounting bracket
cFall Prevention Wire
Be sure to hook the fall prevention wire into an
bracket.
Caution:
When you fix the the dome cover to the dome
camera body, you must insert the wire in the dome
camera body. If not, the wire may obstruct the
camera’s moving.
dMechanics assembly
eDome cover assembly
fBNC connector cover cap
gVideo output cable with BNC connector
Connects with the video connector of the monitor.
hPower cable (AC 24 V)
iData Communication Port (RJ45) - RS-485 and
Alarm Input
a
jData Communication Port (RJ45) - RS-485 and
Alarm Input
kData Communication Port (RJ45) - Alarm
Output
lIF board
mMain control board
b
c
l
m
d
“A” cable to moisture, this may cause leakDo not expose the power and data
age into the housing and damage the camera. If
you must, please make sure that the connections
are sealed tightly.
e
Installation
Precautions
The following steps of installation and connection work
should be done by qualified service personnel or system installers and should conform to all local codes.
Before you install and connect the camera, check and
prepare the required peripheral devices and cables.
Before you connect the camera, turn off all devices to
be connected, such as this camera and DVR.
Note:
Do not touch the dome cover’s window.
Camera Installation Location
Discuss the installation location for the camera with
your retailer, and select a place that is strong enough
for the installation.
•
Install the camera on a ceiling (concrete, etc.) at a
location that is sufficiently strong to support it.
•
Install the camera body on the foundation section
of the building or sections having sufficient bearing
strength.
About Static Electricity Removal
Before installing the camera, touch a metal case or
other metallic parts with your hand to remove static
electricity from your body.
Do not install in areas subjected to high amounts of
humidity or dust.
Doing so may cause internal components to damage
more easily or malfunction.
Do not wire cables near power lines.
Tightening the Screws
Screws should be tightened sufficiently in accordance
with the materials and structure of the installation
location. After tightening the screws, visually inspect
them to make sure there is no unevenness and that
each screw is tight.
Removing the Protection Tape
Before using the camera, remove the protection tape.
Caution: Remove the protection tape carefully.
1. Loosen the screws using the wrench and remove
the dome cover as shown below.
Never install or use the camera in the following locations
•
Do not install it in areas exposed to direct sunlight
or rain.
•
Do not install the camera near the air outlet of an
air conditioner.
•
Near a swimming pool or other areas where chemicals are used.
•
Food preparation areas and other locations where
there are large amounts of steam vapor and oil,
in flammable atmospheres, other special environments.
•
Areas where radiation, X-rays, strong electric
waves, or magnetism is generated.
•
At sea, in coastal areas, or in areas where corrosive gas is being generated.
•
Areas outside of the allowable ambient operating
temperature range.
2. Remove the protection tape and attach the dome
cover.
Pendant mount (Optional)
Install pipe and camera as shown below.
Installation
Mounting the Camera
The figures show an example of the camera mounted
on a wall with a locally procured bracket.
Note:
The camera have not been evaluated for wall or ceiling mounting.
Wall mount (Optional)
Install the camera in the following order.
1. Drill holes on the wall where you want to install the
pipe.
2. Install the pipe and camera as shown below.
How to install
“A”
Pipe threads should be clean and rust
free. Use a sealer (such as Teflon™
tape and silicone sealer) on the threads.
Add thread
sealing tape
Note:
The pipes and brackets for mounting are not
supplied.
Reference: Specifications of LG Standard
pipe.
10
Dipswitch Setting
Note:
ON
6
If you are not using the controller with LG Multix proto7
8
col, there may be some limitation of function control.
6
7
8
6
7
8
5
6
7
8
3. Set the dipswitches inside the housing as per the
1
2
3
4
5
table below.
ON
6
7
8
1
2
3
4
5
The camera has one 8 bit switches that determine the
protocol and baud rate of the data communication.
1
2
3
4
5
Settings are loaded when the camera ON
boots up. Be
sure to turn the camera off, change the dipswitch set1
2
3
4
5
tings, then power back up to load the changes.
ON
ON
1. Turn off the camera.
1
2
3
ON
2. Remove the dome cover from the housing.
SW2 on main board
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
ON
ON
1
BAUD RATE
9 600 BPS
(OFF OFF OFF OFF)
1 200 BPS
(ON OFF OFF OFF)
Installation
4. Power up the camera to load the changes.
4
Switch position (1-4)
2 400 BPS
(OFF ON OFF OFF)
2
3
4
5
6
7
8
4 800 BPS
(ON ON OFF OFF)
19 200 BPS
(OFF OFF ON OFF)
ON
1
38 400 BPS
2
3
ON
1
ON
ON
2
4
3
4
5
5
2
3
4
5
Switch 11position
(5-8)
2
3
4
5
6
6
6
6
7
7
7
7
8
57 600 BPS
8
8
8
Protocol
LG Multix
(OFF OFF
OFF OFF)
ON
1
2
3
4
5
6
7
(ON OFF ON OFF)
(OFF ON ON OFF)
115 200 BPS
(ON ON ON OFF)
8
Reserved 1
(ON OFF OFF OFF)
Pelco D
(OFF ON OFF OFF)
Pelco P
(ON ON OFF OFF)
11
Alarm Output Mode Setting
Camera ID Setting
You can set the Alarm Output to the normal open or
normal close mode.
If you want to use multiple cameras, you should set
camera IDs differently by using the 8-bit Dip switch for
each camera.
SW1 on IF board
Set the camera ID setting referring to the pictures and
the table on the below.
• The default setting of the camera ID is 0.
SW1 on main board
ON
1
Alarm
Output
Number
1
2
3
4
12
Switch
Number
(Position)
Function Effect
1 (ON), 2 (OFF)
Normal Open mode
1 (OFF), 2 (ON)
Normal Close mode
3 (ON), 4 (OFF)
Normal Open mode
3 (OFF), 4 (ON)
Normal Close mode
5 (ON), 6 (OFF)
Normal Open mode
5 (OFF), 6 (ON)
Normal Close mode
7 (ON), 8 (OFF)
Normal Open mode
7 (OFF), 8 (ON)
Normal Close mode
2
3
4
5
6
7
8
The table for the camera ID setting
ID
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
SW1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
SW2
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
SW3
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
SW4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
SW5
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW6
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
13
Installation
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
14
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
Connection
Precautions
•
•
The connections should be made by qualified service personnel or system installers in accordance
with all local codes.
AC 24 V can be used.
Note:
When powered up, the unit performs a self-check
(including one panning, tilting, zooming and focusing operation).
RS-485 connection
Use the cable that is described below for RS-485 site
communication.
•
Shielded, twisted pair cable
•
Low impedance
•
Wire gauge size is thicker than AWG #22 (0.33 mm2).
Connecting monitor
The video signal connection between the camera and
the monitor.
Connection preview
Video output
AC 24 V cable for
Camera
Connections
AC 24 V
BNC plug
data port A Ethernet cable
data port B Ethernet cable
data port C Ethernet cable
Connecting power source
Connect a AC 24 V power source to the power input
terminal.
15
ALARM IN connections
Connect external sensors to the 8-pin haness connector. Each alarm sensor should be connected with G
(GND). Input specifications are low-active, non-voltage contact (ON when active) or open collector (Low
when active).
Connection of the data port and adapter
for alarm input
•
Data Port A
No
1
2
3
4
5
6
7
8
Cautions
•
Alarm input connection must be connected to only
one port of two communication ports.
•
Do not connect one alarm sensor to the several
camera’s alarm input connector.
Description
ALARM IN 1
ALARM IN 2
GND
TRX D TRX D +
GND
ALARM IN 3
ALARM IN 4
Color
Black
Brown
Red
Orange
Yellow
Green
Blue
White
Data Port A Adapter
Alarm sensors
(1 to 4)
Data Port B Adapter
Alarm sensors
(5 to 8)
No
1
2
3
4
5
6
7
8
Description
ALARM IN 1
ALARM IN 2
GND
TRX D TRX D +
GND
ALARM IN 3
ALARM IN 4
Alarm sensor 4
Alarm sensor 3
Alarm sensor 2
Alarm sensor 1
16
Color
Brown
Blue
Yellow
Green
Red
Black
Orange
White
•
Data Port B
No
1
2
3
4
5
6
7
8
Description
ALARM IN 5
ALARM IN 6
GND
TRX D TRX D +
GND
ALARM IN 7
ALARM IN 8
Description
ALARM IN 5
ALARM IN 6
GND
TRX D TRX D +
GND
ALARM IN 7
ALARM IN 8
Color
Black
Brown
Red
Orange
Yellow
Green
Blue
White
Before inputting
the alarm signal
Color
Brown
Blue
Yellow
Green
Red
Black
Orange
White
Function status
Alarm sensor 6
Alarm sensor 5
Alarm Input function
This speed dome camera has a terminal that can
sense the alarm signals.
If the alarm sensor that has installed in a door, window, safe etc. sense a touch or shock, the alarm
sensor send the alarm signal to the camera and the
camera will observe the sensed position.
There are “Manual mode” and “Auto mode” for the
Alarm Input function.
•
Manual mode: Change the observe position to a
sensor that senses a touch or shock then keep
observe the sensed position. (Set the Duration
Time of Alarm Input function to “0” using the
LKD1000 controller.)
•
Manual mode
While observe a
specific position.
Change the observe position to
the alarmed position then keep
observe the alarmed position
and you cannot control the
camera. If you want to control
the camera, you should set the
Duration Time of Alarm Input
function to "1 to 255" using the
LKD1000 controller.
While operating
Preset Tour function.
Stop preset touring and change
the observe position to the
alarmed position then keep
observe the alarmed position.
While operating
Auto Pan function.
Stop auto panning and change
the observe position to the
alarmed position then keep
observe the alarmed position.
While operating
Pattern function.
Stop operating pattern function
and change the observe position to the alarmed position then
keep observe the alarmed position.
Alarm sensor 8
Alarm sensor 7
Alarm signal
input
Connections
No
1
2
3
4
5
6
7
8
<Example: If this unit receives signal from “Alarm 8”>
Auto mode: Change the observe position to a
sensor that senses a touch or shock then return
to the position that previously observed. (Set the
Duration Time of Alarm Input function to “1 to
255”.)
17
<Example : If this unit receives signal from “Alarm 8”>
ALARM OUT connections
Connect an external device, for example, a buzzer or
lamp, to this connector. Output specifications are lowactive, open-collector and a drive capacity of 30 V DC
0.5 A maximum.
Before inputting
the alarm signal
Alarm signal input
Released alarm signal
Alarm output numbers 1 to 4 are linked to alarm
inputs 1 to 4 respectively. If alarm input 1 comes in,
the camera sends output signals via the alarm output
1 connector on the camera.
Note:
Use a relay if the voltage or current of the connected
device exceeds the ratings.
Data Port C Adapter
Function status
Auto mode
While observe a
specific position.
Change the observe position to
the alarmed position then return
to the position that previously
observed.
While operating
Preset Tour function.
Stop preset touring and change
the observe position to the
alarmed position then restart the
preset touring again.
While operating
Auto Pan function.
Stop auto panning and change
the observe position to the
alarmed position then restart the
auto panning again.
While operating
Pattern function.
Stop operating pattern function and change the observe
position to the alarmed position
then restart the pattern function
again.
Note:
The Alam In 1 is Preset 1, Alam In 2 is Preset 2, Alam
In 3 is Preset 3,...,Alam In 7 is Preset 7 and Alam In 8
is Preset 8.
18
Alarm devices
(1 to 4)
Connection of the data port and adapter
for alarm output
•
Data Port A or B
Adapter
Data Port C
No
1
2
3
4
5
6
7
8
Description
ALARM OUT 1
COM 1
ALARM OUT 2
COM 2
ALARM OUT 3
COM 3
ALARM OUT 4
COM 4
Color
Black
Brown
Red
Orange
Yellow
Green
Blue
White
Color
Brown
Blue
Yellow
Green
Red
Black
Orange
White
Alarm device 4
Alarm device 3
LKD1000 controller
Connection of the data port and adapter
with LKD1000 controller
No
4
5
No
4
5
Description
TRX D TRX D +
Description
TRX D TRX D +
Color
Orange
Yellow
Connections
No
1
2
3
4
5
6
7
8
Description
ALARM OUT 1
COM 1
ALARM OUT 2
COM 2
ALARM OUT 3
COM 3
ALARM OUT 4
COM 4
Color
Green
Red
Alarm device 2
Alarm device 1
Connecting LKD1000 controller
TX-
TX-
TX+
TX+
TXTX+
Connecting the LKD1000 controller to control the camera. (Refer to the manuals of the LKD1000 controller
for more details.).
19
System Connection
Note:
When any peripheral is turned off and turned on
again, the camera is also turned off and turned back
on.
Caution:
Do not connect the alarm connectors to the another
camera’s alarm connectors.
Controller
or
To Alarm devices
Caution:
Connect the supplied
termination adapter
to the final camera’s
data port (B) to prevent the RS-485 communication error.
To Alarm
devices
20
Main Menu
Operation
Contents
AUTO
LOW/
MIDDLE/
HIGH
5, 10, 15,
DWELL TIME
30, 60 s
INITIAL SET
RET/TOP/
EXIT
END
D/N LEVEL
Setup Menu Overview
DAY/NIGHT
The following table shows the list of menu items and
options. You can adapt the camera to your requirements by setting up the respective items in these
menus.
Main Menu
Sub Menu
Sub Menu
MOTION
DET
ON
OFF
MASK
NUMBER
PRIVACY
MASK
ON
AUTO
COLOR
TEMP
MANUAL
INDOOR,
OUTDOOR
RED
-100 to 100
BLUE
-100 to 100
INITIAL SET
EXIT
RET/TOP/
END
MASK1 to
MASK8
MASK STATE
ONE PUSH
WHITE
BALANCE
ZONE
ZONE1 to
NUMBER
ZONE4
ZONE STATE OFF, ON
WIDTH
HEIGHT
MOVE X
MOVE Y
SENSITIVITY
INITIAL SET
RET/TOP/
EXIT
END
3D-DNR
OFF, ON
BLACK,
MASK
GRAY,
COLOR
WHITE
WIDTH
HEIGHT
MOVE X
MOVE Y
RESET MASK
INITIAL SET
RET/TOP/
EXIT
END
Operation
Contents
AUTO/ ONE PUSH/ ZOOM
FOCUS MODE
TRIG/ MANUAL
FOCUS DIST
50 cm, 1 m, 3 m, 5 m
ZOOM START
x1 to x26
ZOOM END
x2 to x324
FOCUS
ZOOM SPEED SLOW/ MIDDLE/ QUICK
AUTO/ MANUAL/ AUTO
ZTRK MODE
ONLY
INITIAL SET
EXIT
RET/TOP/END
IRIS
AUTO/MANUAL
AGC
OFF/LOW/MIDDLE/HIGH
WDR/BLC
OFF/WDR/BLC/HSBLC
BRIGHTNESS
0 to 100
X512,
to,
x2, AUTO, OFF,
EXPOSURE
SHUTTER
A.FLK, 1/160, to, 1/90 000
OFF, AUTO x2 to AUTO
SENS-UP
x128
INITIAL SET
EXIT
RET/TOP/END
ATW
DAY
NIGHT
OFF
OFF
LOW
MIDDLE
HIGH
21
Main Menu
Sub Menu
CAMERA ID
D-EFFECT
COLOR
FREEZE
SHARPNESS
STABILIZER
SPECIAL
OSD
RESET
LANGUAGE
INITIAL SET
EXIT
FACTORT
RESET
S/W VERSION
REBOOT
EXIT
Contents
0 to 255
Not supported.
OFF
ON
COLOR LEVEL
OFF/ ON
0 to 68
OFF/ ON
OFF
USER TITLE
ZOOM MAG
ON
FUNCTION
CAMERA ID
ENG or ENG/CHI
Menu navigation
We use the LKD1000 controller in this manual to
explain the features of the LG Dome camera because
of the LKD1000’s ability to control all of the LG Dome
camera’s advanced features. (For detailed controller
instructions, refer to the LKD1000 Controller Manual.)
RET/TOP/END
Buttons
RET/TOP/END
EXIT
Note:
The Preset, Auto Pan, Pattern, Alarm functions could
not be set on the OSD menu. To set these functions,
use LKD1000 controller.
Function
Cam OSD
button
Displays the setup menu
or cancels operation of
the setup menu.
ZOOM IN
button
Use to move upper
direction on the menu
screen.
ZOOM OUT
button
Use to move lower direction on the menu screen.
FOCUS
NEAR button
Use for increase the
value of the option.
FOCUS FAR Use for decrease the
button
value of the option.
Open/
Close(Enter)
buttons
22
Executes selections and
displays a submenu for
an item with the mark.
Accessing setup menus
To access the setup menus using the keys on a
LKD1000 controller, do the following:
1. Select CAM (Camera) icon in the main menu and
then press ENTER. The camera ID input menu will
be displayed.
CAM
CAM
General Operation
1. Use [In] or [Out] button to select an option then
press [Open] or [Close] button.
Submenu appears on the monitor.
2. Use [In] or [Out] button to select a submenu
option.
3. Use [Near] or [Far] button to select a value.
4. Select [EXIT] option then press [Open] or [Close]
to exit the setup menu. In the submenu, use [In] or
[Out] button to select the [EXIT] then use [Near]
or [Far] button to select a mode and press [Open]
or [Close] to exit the setup menu.
•
•
Please Enter Camera ID
Please
Camera
Target Enter
CAM ID
: _ ID
Target CAM ID : _
2. Enter the connected camera ID to control the camera connected to the LKD1000 controller directly
and then press ENTER. The camera control menu
will be displayed.
PRESET
/CAM1
PRESET
/CAM1
3. Press [Cam OSD] button to display the camera
setup menu.
•
RET: Return to the previous.
TOP: Return to the CAMERA SETTING menu
screen.
END: Exit the setup menu.
Focus setting
Focus Mode setting
The camera adjusts the focus automatically by sensing the center of the picture.
•
AUTO: Auto-focus is activated automatically.
•
ONE PUSH: The focus is activated manually. If the
camera is received auto-focus command, the camera is activated Auto-focus mode and the focus is
set automatically and then the focus mode is automatically changed to manual mode.
•
ZOOM TRIG: The focus is activated manually.
If you change the zoom, the focus is activated
Automatically and then the focus mode is automatically changed to manual mode.
•
MANUAL: Focus is activated only when the
FOCUS (NEAR or FAR) keys on the controller is
pressed.
At this point, you have access to the camera setup
menu.
23
Operation
Select [FOCUS MODE] option on the [FOCUS] menu,
then select the following mode.
Focus Distance setting
Zoom Speed setting
Selects the minimum shooting distance for the focus.
Selects a zoom speed.
Select [FOCUS DISTANCE] option on the [FOCUS]
menu, then select a focus distance value (50 cm, 1 m,
3 m, 5 m).
Select [ZOOM SPEED] option on the [FOCUS]
menu, then select a zoom speed (SLOW, MIDDLE or
QUICK).
Zoom Start setting
You can set the zoom start position of the camera.
When the zoom function is operated, the zoom always
will start at the selected zoom start position.
Select [ZOOM START] option on the [FOCUS] menu,
then set a zoom start position (x1 to x26).
Zoom End setting
You can set the zoom end position of the camera. If
you set the zoom end position, the zoom is operated
up to the selected zoom end position.
Select [ZOOM END] option on the [FOCUS] menu,
then set the zoom end position ("Zoom Start position+1" to x324).
24
Zoom Tracking Mode setting
Selects a zoom tracking mode. Zoom tracking means
focused zooming state.
Select [ZTRK MODE] option on the [FOCUS]
menu, then select a zoom tracking mode (AUTO or
MANUAL).
If the FOCUS MODE is set to [AUTO], the ZTRK
MODE is set to [AUTO] and you can not change the
ZTRK MODE.
Exposure settings
Iris setting
•
Select the desired lens iris value for camera exposure.
Select [IRIS] option on the [EXPOSURE] menu, then
select a value. (AUTO or MANUAL).
•
AUTO: The lens iris is set automatically.
•
MANUAL: Use [Near] or [Far] button to select the
DC Iris level.
AGC (Automatic Gain Control) setting
If the images are too dark, change the maximum
[AGC] value to make the images lighter.
BLC: Set the BLC limit.
-
•
•
WDR LEVEL: LOW y MIDDLE y HIGH
BLC LEVEL: LOW y MIDDLE y HIGH
HSBLC: Use for adjusting brightness the
specific area of picture. The HSBLC mode is
automatically activated only in low illuminance
scene.
-
AREA SETTING: Use [Near] or [Far] button to select a area then use [In] or [Out]
button to select a ON or OFF. Press [Open]
or [Close] to exit the area setting menu.
-
GRAY SCALE: Use [Near] or [Far] button
to select a gray scale.
(GRAYyD.GRAYyBLACK).
-
HS LEVEL: Use [Near] or [Far] button to
select a bright level. (5 level)
-
MASK STATE: Use [Near] or [Far] button
to select [ON] or [OFF].
If you set the MASK STATE to ON, the
mask function is activate only when the
HSBLC is activated by auto mode.
OFF: Not used.
1. Select [AGC] option on the [EXPOSURE] menu.
BRIGHTNESS setting
You can increase the brightness of the darkened
video. If you set the brightness to lower value, the
image is darkened. If you set the brightness to higher
value, the image gets bright.
2. Use [Near] or [Far] button to select a mode.
(OFFy LOWyMIDDLEyHIGH)
1. Select [BRIGHTNESS] option on the [EXPOSURE]
menu.
Operation
WDR/BLC setting
Use WDR/BLC option to set the options for BLC or
WDR camera.
1. Select [WDR/BLC] option on the [EXPOSURE]
menu.
2. Use [Near] or [Far] button to set the bright level.
2. Use [Near] or [Far] button to select a mode then
press [Open] or [Close].
•
WDR: Set the WDR limit.
25
SHUTTER (Shutter Speed) setting
Select the desired shutter speed for camera exposure.
You can change the shutter speed to higher speed
to capture fast-moving subjects, though the image
becomes darker.
1. Select [SHUTTER] option on the [EXPOSURE]
menu.
2. Use [Near] or [Far] button to set shutter speed.
(x512 to x2 y AUTOy OFF y A.FLK y 1/160
to 1/90 000)
White Balance setting
Select the method by which the camera shifts its
output colors to compensate for the color of a light
source.
1. Select [WHITE BALANCE] option on the
[CAMERA SET] menu.
2. Use [Near] or [Far] button to select a mode then
press [Open] or [Close].
•
SENS-UP setting
If pictures are not clear due to darkness, use for
increase the sensitivity of picture.
1. Select [SENS-UP] option on the [EXPOSURE]
menu.
•
2. Use [Near] or [Far] button to set the SENS-UP
limit (OFF, AUTO x2 to AUTO x128).
To setting the SENS-UP funtion, select the [AUTO]
on the [SHUTTER].
Note:
If you set to one of the SHUTTER options except
AUTO on the [SHUTTER] menu, the [SENS-UP] setting is not available and [---] mark is displayed.
26
ATW (Auto-Tracing White Balance): In this
mode, the The color temperature range for the
proper white balance is approximately 1 800
to 10 500 K. Proper white balance may not be
obtained under the following conditions:
-
When the color temperature is out of the
1 800 to 10 500 K range.
-
When the scene contains mostly high color
temperature objects, such as a blue sky or
sunset.
-
When the scene is dim.
AUTO: In this mode, the color temperature
range for the proper white balance is approximately 2 700 to 5 400 K. Proper white balance
may not be obtained under the following conditions:
-
When the color temperature is out of the
2 700 to 5 400 K range.
-
When the scene contains mostly high color
temperature objects, such as a blue sky or
sunset.
-
When the scene is dim.
•
ONE PUSH: If you select the ONE PUSH
mode, you will be able to set up the White
Balance automatically using [Open] or [Close]
button.
•
MANUAL: You can set the white balance
options manually.
Note:
If you set the AGC to [OFF] or the SHUTTER
is set to one of the SHUTTER options except
AUTO on the [EXPOSURE] menu, the AUTO
mode of the DAY/NIGHT function is not available and [---] mark is displayed.
-
COLOR TEMP: Use [Near] or [Far] button
to select a function.
> INDOOR: The color temperature range
for the proper white balance is approximately 3 200 K.
> OUTDOOR: The color temperature
range for the proper white balance is
approximately 5 100 K.
-
RED: Set the desired red value.
(-100 to 100)
-
BLUE: Set the desired blue value.
(-100 to 100)
•
DAY: Color mode enabled.
•
NIGHT: Black-and-white mode enabled.
Motion Detection setting
The motion detection detects the moving objects in
the scene by monitoring changes in brightness level.
You can select the level of sensitivity for motion detection to 4 zone.
1. Select [MOTION DET] option on the [CAMERA
SET] menu.
2. Use [Near] or [Far] button to select a [ON]
and press [Open] or [Close]. The MOTION
DETECTION menu appears.
Day/Night setting
1. Select [DAY/NIGHT] option on the [CAMERA SET]
menu.
3. Use [Near] or [Far] button to select a zone number (ZONE1 to ZONE4) on the [ZONE NUMBER]
option.
•
AUTO: You will be able to change the Day/
Night mode automatically.
-
D/N LEVEL: Use [Near] or [Far] button to
select a level.
(LOWyMIDDLEyHIGH)
-
DWELL TIME: Use [Near] or [Far] button
to select a dwell time. (5, 10, 15, 30 or 60
s.)
Operation
2. Use [Near] or [Far] button to select mode for day/
night function.
4. Use [Near] or [Far] button to set up the ON or
OFF on the [ZONE STATE] option. If you set to
ON, the zone frame appears on the center of the
monitor.
5. Use [In] or [Out] to select an option then use
[Near] or [Far] button to adjust the option
•
WIDTH: Enlarge or decrease the horizontal
size of the zone frame.
•
HEIGHT: Enlarge or decrease the vertical size
of the zone frame.
•
MOVE X: Moves horizontal position of the zone
frame.
•
MOVE Y: Moves vertical position of the zone
frame.
6. Use [SENSITIVITY] option to obtain the optimum
detection level.
27
Privacy Mask setting
This function is aiming at the protection of personal
privacy, selecting a screen part black not to be displayed in the screen. Up to 8 zones can be registered.
1. Select [PRIVACY MASK] option on the [CAMERA
SET] menu.
istered mask color will be changed automatically
with the same color for each of group (MASK1 to
4, MASK5 to 8).
3D-DNR setting
2. Use [Near] or [Far] button to select a [ON] and
press [Open] or [Close]. The PRIVACY MASK
menu appears.
3. Use [Near] or [Far] button to select a zone number (MASK1 to MASK8) on the [MASK NUMBER]
option.
4. Use [Near] or [Far] button to set up the ON or
OFF on the [MASK STATE] option. If you already
registered the mask zone and set to ON, the mask
zone box appears on the monitor.
5. Use [Near] or [Far] button to select the color of
the mask zone box on the [MASK COLOR] option.
6. Select [RESET MASK] and press [Open] or
[Close]. If you register the mask zone for the first
time, the mask zone box appears on the center of
the monitor. If you already registered mask zone,
it will be returned to its initial state and appear on
the center of the monitor.
7. Use [In] or [Out] to select an option then use
[Near] or [Far] button to adjust the option.
•
WIDTH: Enlarge or decrease the horizontal
size of the mask zone box.
•
HEIGHT: Enlarge or decrease the vertical size
of the mask zone box.
•
MOVE X: Moves horizontal position of the
mask zone box.
•
MOVE Y: Moves vertical position of the mask
zone box.
Notes:
•
If you want to reset the mask zone position, select
RESET MASK option and press [Open] or [Close]
button.
•
The parts with the registered mask numbers from
MASK1 to MASK4 have the same color. (So
do the parts with the numbers from MASK5 to
MASK8). If you change the mask color, the reg-
28
1. Select [3D-DNR] option.
If pictures are not clear due to brightness, use for
reduce the noise of picture.
2. Use [Near] or [Far] button to select a option.
(OFFyLOWyMIDDLEyHIGH)
Notes:
•
If you set the AGC to [OFF] on the [EXPOSURE]
menu, the [3D-DNR] function is not available.
•
When you use this function, the afterimage may
occur.
Special menu settings
Camera Identification setting
Only displays the camera’s ID. Use the internal 8 bitDIP switch if you want to set ID.
D-EFFECT (Digital effect) setting
This model does not support the D-EFFECT function.
2. Use [Near] or [Far] button to change a adjust the
option. If you set the sharpness value to higher,
the image outline becomes sharp. If you set to
lower value, the image outline becomes dim.
Color setting
Stabilizer setting
You can switch the displayed picture to grayscale or
color.
1. Select [COLOR] option on the [SPECIAL] menu.
2. Use [Near] or [Far] button to change a color
effect.
• ON: To display the picture with color.
Select ON and Press [Open] or [Close] to display the submenu.
You can adjust the color level using the [Near]
or [Far] button.
• OFF: To display the picture with grayscale.
Freeze setting
1. Select [FREEZE] option on the [SPECIAL] menu.
The image stabilizer function minimizes the appearance of shaky images caused by low-frequency vibration.
This function is useful for outdoor surveillance.
Select [STABILIZER] option and set to ON or OFF.
Note
If you set the [STABILIZER] to ON, the Digital zoom is
set to [x1.1] automatically.
OSD setting
You can set the Function On-Screen Display options
using the [OSD] menu.
The Function On-Screen Display of this camera can
be turned on or off.
1. Select [OSD] option on the [SPECIAL] menu.
2. Use [Near] or [Far] button to select a [ON] and
press [Open] or [Close]. The OSD menu appears.
Operation
2. Use [Near] or [Far] button to set up the ON or
OFF.
Sharpness setting
Sharpens the image outline.
1. Select [SHARPNESS] option on the [SPECIAL]
menu.
3. Use [In] or [Out] to select an option then use
[Near] or [Far] button to set the option.
• ON: Displays the Function OSD on the screen.
• OFF: The Function OSD dose not appear on
the screen.
29
User title setting
You can use the camera identification to assign a
number and character to the camera (0 to 9, A to Z, a
to z). The USER TITLE is displayed on the upper left
of the screen.
To disappear the user title, select [OFF].
Language setting
Select a language for setup menu and information
display.
1. Select [USER TITLE] option on the [SPECIAL]
screen.
2. Use [Near] or [Far] button to select a [ON] then
press [Open] or [Close]. The USER TITLE menu
appears.
Reset settings
A
3. Use [In], [Out], [Near] or [Far] button to select a
character or number.
1. Select [RESET] option.
2. Press [Open] or [Close] button and the RESET
menu appears.
- CLR: If you enter the wrong code, select CLR
then press [Open] or [Close].
- POS: Use [Near] or [Far] button to move position of USER TITLE on the screen.
- END: Confirm your selection.
- A(Blank): Insert a space at the cursor position.
-
/
: Moves cursor to left or right.
3. Use [In] or [Out] to select option.
• FACTORY RESET: Clear certain settings and
information and return to factory default settings.
• S/W VERSION: Displays the software version
on the monitor.
• REBOOT: Reboot the camera system.
4. Press [Open] or [Close] to confirm your selection.
30
Reference
Specifications
Signal System
NTSC (High Resolution)
PAL (High Resolution)
Pick-Up Device
4.5 mm EX-view HAD CCD
Total Pixels No
410 K
Horizontal Resolution
More Than 540 TV Lines
Lens
x27 Zoom ( F1.5(Wide Angle), F3.6(Tele)), f = 3.25 mm to 88 mm
S/N Ratio
More Than 50 dB (AGC Off)
Day & Night
Day / Night / Auto
Min. Illumination(Lux)
Color: 0.003 (0.6, Sens-up Off), B/W: 0.0001 (0.1, Sene-up Off)
Digital Zoom
X 12
Sync System
Internal
White Balance
Auto / ATW/ ONE PUSH / Manual(1 800 K to 10 500 K)
Control method
RS-485 Control
Alarm Input
8 Channel
Alarm Output
4 Channel
Video Output
Composite Output 1 Vp-p (75 Ω Terminated)
Electronic Shutter
1/60 to 1/90 000 s
Iris Control
Auto / Manual
Wide Dynamic Range
Dual Shutter Control ( 60 dB)
Panning Range (Speed)
0º to 360º, Max. 240º/s
Tilting Range (Speed)
0º to 180º, Max. 240º/s
Privacy Zone
8 Area Active Programmable Zone
Preset/ID
128 Position / 256
Auto Panning
2 to 8 points
Pattern
Max. 8 minutes
Group Tour
Max. 9 Groups
Operation Temperature
-10 to 50 ºC (Humidity: 0 % RH to 80 % RH)
Safekeeping Temperature
-30 to 60 ºC (Humidity: 0 % RH to 85 % RH)
Power Supply
AC 24 V
Power Consumption
Max. 20 W
Dimension(ø x H )
ø 230 mm x 332 mm(H)
Weight
Approx 3.3 kg
470 K
1/50 to 1/90 000 s
Reference
31
P/NO : MFL62034716
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising