LG | LVC-SX810HP | LG LVC-SX810HP Owner’s Manual

LVC-SX810HM_HP_ENG_77T
7/6/06
2:51
PM
Page
1
LG Video Camera
Instruction Manual
Models
Before
:
LVC-SX810HM/HP
installing, operating or adjusting this
product, please read this instruction booklet
carefully and completely.
LVC-SX810HM_HP_ENG_77T
7/6/06
2:51
PM
equipment generates, uses, and can radiate radio frequency
and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct
energy
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
flash with arrowhead
lightning
triangle
lateral
ence
symbol
is intended to alert the
of uninsulated
2
This
CAUTION
This
Page
user
dangerous voltage
within
an
the interference at his
?Asuitable
?
equi-
to the pres-
within the
prodmagnitude to
uct's enclosure that may be of sufficient
a risk of electric shock to persons.
own
expense.
conduit
entries, knock-outs or glands shall be provided in
product in the end user.
Caution: Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manuthe cable entries of this
facturer's instructions.
?
Holes in
metal, through which insulated wires pass, shall have
or shall be provided with brushings.
smooth well rounded surfaces
constitute
The exclamation
equilateral triangle is
intended to alert the user to the presence of important
and
maintenance
operating
(servicing) instructions in the
literature accompanying the product.
point
within
an
Warning:
Do not install this
bookcase
or
equipment
in
a
confined space such
as a
similar unit.
in the instruction manual. The
Warning: Wiring methods shall be in accordance with the National
Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
Warning: To reduce a risk of fire or electric shock, do not expose this
product to rain or moisture.
Caution: This installation should be made by a qualified service per-
this
son
FCC WARNING : This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause
harmful interference unless the modifications are expressly approved
user could lose the authority to operate
equipment if an unauthorized change or modification is made.
Notices
For
U.S.A
Regulatory
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment.
2
and should conform to all local codes.
Caution: To avoid electrical
shock, do not open the cabinet. Refer
qualified personnel only.
Caution: The apparatus should not be exposed to water (dripping or
splashing) and no objects filled with liquids, such as vases, should be
placed on the apparatus.
servicing
to
7/6/06
LVC-SX810HM_HP_ENG_77T
2:51
PM
3
Page
Important Safety Instructions
1.
Read these instructions.
-
All these
and
operating instructions should
before the product is operated.
2.
Keep
ing
these instructions.
and
use
-
The
safety
7.
be read
er 's
Heed all
Slots and openings in the
provided for ventilation, to ensure
reliable operation of the product, and to protect
it from over- heating. The openings should
never be blocked by placing the product on a
instructions should be retained for
warnings.
uct and in the
-
All
operating
warnings
on
the
prod-
product
Follow all instructions.
use
5.
6.
All
operating
and
-
Clean
only
with
dry
cloth.
uct from the wall outlet
liquid
other similar surface. This
as a
ventilation is
placed
bookcase
provided
in
a
built-in instal-
rack unless propand the manufacturor
er's instructions have been adhered to.
Do not use this apparatus near water.
For
example: near a bath tub, wash bowl, kitchen
sink, laundry tub, in a wet basement; near a
swimming pool; etc.
use
er
instructions should be followed.
or
should not be
lation such
-
-
are
bed, sofa, rug
instructions should be
adhered to.
4.
instructions.
cabinet
safety, operat-
future reference.
3.
Do not block any ventilation openings.
Install in accordance with the manufactur-
8.
Do not install
near
any heat
sources
such
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that proas
duce heat.
Unplug this prodbefore cleaning. Do not
-
cleaners.
3
LVC-SX810HM_HP_ENG_77T
7/6/06
2:51
PM
Page
4
Important Safety Instructions
9.
Do not defeat the
polarized
ized plug
or
safety purpose of the
grounding-type plug. A polar-
has two blades with
one
12.
wider
than the other. A grounding type plug has
two blades and a third grounding prong.
facturer, or sold with
apparatus. When a cart is
used, use caution when
The wide blade
or the third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an
electrician for
replacement
11.
being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
Only use attachments/accessories speciby the manufacturer.
the cart/ appara-
injury
from
tip-
over.
13.
Protect the power cord from
fied
4
moving
tus combination to avoid
of the obsolete
outlet.
10.
Use only the cart, stand,
tripod, bracket, or table
specified by the manu-
Unplug
storms
this apparatus during lightning
when unused for long periods
or
of time.
14.
Refer all
servicing to qualified service perServicing is required when the
apparatus has been damaged in any way,
such as power- supply cord or plug is
damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
sonnel.
LVC-SX810HM_HP_ENG_77T
7/6/06
2:51
PM
Page
5
Contents and Features
Contents
Features
PartNamesandFunctions...............6-7
This color video
Connections........................8
camera is designed for use in monitoring system.
High resolution and high sensitivity with a 1/3
inch Super HAD CCD (Charge Coupled Device)
CS Mount (Adapter Ring Mount for C Lens:
Optional)
The input power source is DC 12V (4.5W (Max)).
?
MountingtheLens..................9-10
.11-12
Concerning Auto-Iris Lenses
FunctionSwitchSettings................13
.14-15
Day&Night Function Settings
Flange-backAdjustment................16
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
InstallationofCamera.................17
Specifications.....................18-19
?
?
Maintenance of the unit
?
Remove dust
with
?
a
or
dirt
on
the surface of the lens
blower.
dry soft cloth to clean the body. If it is
dirty, use a cloth dampended with a small
quantity of neutral detergent and then wipe dry.
Use
a
very
?
Avoid the
ners,
may
use
of volatile solvents such
as
thin-
alcohol, benzene, and insecticides. They
damage
the surface of the
body.
5
LVC-SX810HM_HP_ENG_77T
7/6/06
2:51
PM
Page
6
Part Names and Functions
1.
Camera
mounting
The bracket
of the
2.
camera.
bracket
be fixed at the top
or
bottom
(page 17)
Lens mount cap
The cap is installed to protect the lens mount
section. Remove the lens mount cap before
installing
6
can
a
lens
(sold separately).
lock
3.
Flange-back
4.
Flange-back adjustment
screw
dial
LVC-SX810HM_HP_ENG_77T
7/6/06
2:51
PM
Page
7
Part Names and Functions
7.
D&N connector for manual
8.
Video
output
Connect this connector to
VCR
9.
monitor with
or
a
setting
(BNC type)
connector
a
device such
Function switches for manual
To set
functions,
10. Lens iris
This 4control
output
use
as a
VIDEO IN connector.
these
dip
connector
setting
switches.
(LENS)
pin connector is used to send the Iris
signal and power supply to an auto-iris
type lens.
11. DC iris level
12. ALC Lens
volume
adjustment
Setting Switch
DC: When you attach an Auto Iris lens requirthe DC control signal, please put this
ing
5.
when the power to the
Power input terminal
Comes
6.
switch in the DC
Power indicator
on
DC 12 V
This
input
camera
camera
is
on.
terminal.
must
Certified/Listed,
always
be
operated a DC 12
supply only.
class 2 power
V
position.
ELC: When you attach a manual or fixed lens,
please put this switch in the ELC position.
VIDEO: When you attach an Auto Iris lens
requiring the video control signal, please put
this switch in the VIDEO
position.
7
LVC-SX810HM_HP_ENG_77T
7/6/06
2:51
PM
Page
8
Connections
3
Basic connection
The
2
AC
peripheral devices (VCR, monitor, lens, etc.),
adaptor and cables are not supplied.
1.
Connecting
camera
2.
Use
connection between the
or
12V
time
lapse
VCR.
available
commercially
Certified/Listed, Class 2,
with
a
DC 12 V
adaptor.
DC 12 V power source to the DC
terminal on the back of the camera
an
input
3 and # aligned correctly
3. Insert the
1
signal
and the monitor
Connect
8
the monitor
Make the video
plug
as
shown left.
of this power cord into
outlet.
The POWER indicator will
light.
a
wall
LVC-SX810HM_HP_ENG_77T
Mounting
7/6/06
2:51
PM
Page
9
the Lens
Remove the lens mount cap from the
2. Install the auto-iris lens.
1.
2-1. CS mount
1
camera.
type lens
the lens mount with the
Carefully align
opening, then
turn the lens
2-2. C mount
type lens
slowly
camera
to install it.
To allow for
flange- back adjustment, install the
C-mount adaptor (option) on the lens mount,
then carefully align the lens mount with the
camera opening and turn the lens slowly to
2-2
install it.
3.
Connect the lens
connector
3
2-1
(LENS)
When
using
shape
may not
the
plug
on
to the lens iris
the back of the
output
camera.
lenses from other makers, the
correspond to the terminal
plug
on
camera.
In such
a case, remove the original plug and
using a soldering iron, connect a lens iris plug
according to the diagram. (Refer to next page.)
9
LVC-SX810HM_HP_ENG_77T
Mounting
Pin
layout
7/6/06
2:51
PM
10
Page
the Lens
for the lens iris
output
connector
Rewire the lens iris
1.
plug
Cut off the
plug of the lens cable, cut off
approximately 8mm of the insulation, and then
strip approximately 2mm of the ends of the
cable sheaths.
8mm
2mm
type lenses
No.
DC
1
2
Damping
Damping
3
Drive
4D rive
10
+
-
-
+
VIDEO
Vcc
type lenses
(+9V)
2.
Solder the ends of the cable wires to the ends
Not used
of the
Video
lens iris
Ground
pins, and
plug.
then attach the
cover
of the
7/6/06
LVC-SX810HM_HP_ENG_77T
Concerning
DC
2:51
PM
Auto-Iris Lenses
type auto-iris lens
A lens without driver circuit that
operates only on
a DC power source. In general, this type of lens is
referred to as DC type coil lens. (Set the ALC Lens
Setting
Switch to the DC
CAUTION
11
Page
ELC
Use
a
type auto-iris lens
manual
Setting
or
fixed iris lens
Switch to the ELC
(Set the
position.)
ALC Lens
position.)
Depending on the type of lens used, the lens
may not perform properly. In such a case, adjust the LEVEL
volume on the lens casing to correct.
:
11
7/6/06
LVC-SX810HM_HP_ENG_77T
Concerning
2:51
PM
Page
12
Auto-Iris Lenses
type auto-iris lens
VIDEO
A lens with
amplifier
circuit that operates
on
video
and DC power source. In general, this type of
lens is referred to as EE amplifier type lens.
signal
ALC and LEVEL volume level controls
on
Setting
Switch to
CAUTION
?
adjustments. (Set the
the VIDEO position.)
ALC Lens
:
Be cautions not to
Notes
available
are
the lens for iris
use
Auto Iris Lens with
over
30mA.
:
Set the ALC and LEVEL controls
on the lens to adjust the
Normally the ALC volume should be turned all the way
to Av (Average).
Depending on the type of lens used, the lens may not
perform properly. In such a case, adjust the LEVEL volume on the lens casing to correct.
iris.
?
12
LEVEL volume
ALC volume
level control
ALC
LEV E
L
level control
LVC-SX810HM_HP_ENG_77T
7/6/06
Function Switch
2:51
PM
Page
13
Settings
No
1
Name
White Balance
2A G C
Gain
(Back Light
Compensation)
4F L
HOLD
White Balance Hold
D&N
(Day
*
Factory Setting
&
Night)
Note: When you
screen
while
switching the
changing filter.
tracking
AGC level varies from 10dB to
maximum 30dB
OFF
10dB
ON
Sets to this
position
light
in behind the target
(Max.)
comes
when strong
OFF
Normal
ON
Shutter
speed
(NTSC : 1/100
is fixed.
OFF
Shutter
is not fixed
(Flickerless)
5
White Balance
AWB
Control)
BLC
Function Effect
Auto
ON
(Auto
3
Position
position
speed
D&N AUTO
Auto mode
D&N MAN
Manual mode
D&N
function, noise
sec, PAL
may appears
:
1/120 sec)
on
the
13
7/6/06
LVC-SX810HM_HP_ENG_77T
Day&Night
2:51
Function
PM
Night
The D&N function is activated
automatically
AGC
ON mode.
the
rear
Notes
dip
panel.
14
Settings
Auto Mode
Set the D&N
Page
switch to D&N AUTO
position
on
Lock function in Auto mode
The D&N Auto function is fixed to
night
Close the connected External
for this funciton.
Note
S/W
mode.
:
If you disconnet the external
S/W
from the D&N terminal,
the D&N function is set to auto mode.
:
?I t is not necessary to connect the D&N terminal to
con-
trol D&N auto function.
?
If you
use
the IR illumination, the
Day and Night func-
tion may be switch again and again. In this case,
the manual mode or Night Lock function.
use
Close
External S/W
14
7/6/06
LVC-SX810HM_HP_ENG_77T
Day&Night
2:51
Function
PM
can
the
rear
2. Connect
rear
Day
Night
set the D&N function
1. Set the D&N
dip
panel.
an
15
Settings
Manual Mode
You
Page
manually.
switch to D&N MAN
external
S/W
position
to D&N terminal
on
on
function
When you close the external
is set to night mode.
S/W,
the D&N funciton
the
panel.
function
When you open the external
is set to Day mode.
S/W,
the D&N funciton
Close
External S/W
Open
External S/W
15
LVC-SX810HM_HP_ENG_77T
7/6/06
2:51
PM
16
Page
Flange-back Adjustment
The
adjustment is required only when a lens withfocus-adjusting mechanism is mounted, or
when a lens with adjusting mechanism is mounted
1
Loosen the flange-back fixing
flange-back adjusting ring.
2.
Turn the
out
and focus that is
more
accurate is needed.
focused
screw on
the
flange-back adjusting ring to obtain
point while watching the monitor
a
screen.
3.
flange-back
fixing screw
flange-back
adjusting ring
Tighten the flange-back fixing
flange-back adjusting ring.
the
Caution:
Tightening
the
the
screw or
Note: The
source
light.
16
screw on
screw
by
force will
cause
damage
to
deviation of focus.
object may be out of focus when using a
of near-infrared light than using the visible
LVC-SX810HM_HP_ENG_77T
7/6/06
2:51
PM
Page
17
Installation of Camera
The bracket
(optional)
can
be installed to either
the top of the camera as desired. When changing
the position of the camera mounting bracket, you
should
always
reuse
the
screws
that have been
removed.
Notes:
?
If
using
a camera
mounting bracket,
select
a
location that is strong enough to bear the full
weight of the camera and the mounting bracket
for
long periods, and install
mounting bracket securely.
?
The
camera
the
camera
and
has not been evaluated for wall
or
ceiling mounting.
17
LVC-SX810HM_HP_ENG_77T
7/6/06
2:51
PM
Page
18
Specifications
Model
Signal System
Total/Effective
Pick-Up Device
Pixels
Lens
Iris Control
Signal Process
Scanning System
Sync. System
Scanning Frequency
LVC-SX810HM
LVC-SX810HP
NTSC
PAL
410K/380K
470K/440K
1/3 Inch Interline Color CCD(Super HAD)
C / CS MOUNT (Adapter Ring Mount for C Lens: Optional)
DC/ELC/VIDEO
Digital Signal Process
-
2:1 Interlace
Internal
59.94Hz(VD)
50Hz(VD)
Resolution
S/N
Ratio
Standard Illuminance
Sensitivity (1/3 Output)
Video Output Signal
Day & Night
Back Light
18
500Lines
More than 50 dB
2000Lux
(3200°K)
(Infrared ON : Night Mode)
1Vp-p Composite (75Ω)
Auto / Manual / EXT
Manual ON / OFF (with DIP Switch)
0.4Lux
(F1.0),
0Lux
LVC-SX810HM_HP_ENG_77T
7/6/06
2:51
PM
Page
19
Specifications
Model
Gain Control
Flickerless
White Balance
Exposure
LVC-SX810HM
LVC-SX810HP
ON
OFF
(Max. 30dB) /
(Max.10dB) (with DIP Switch)
ON / OFF (with DIP Switch)
AWB / Hold (White Balance Hold)
Automatic control with DC Iris meter / Video Iris meter
/ Auto Electronic Shutter (Max. 1/100000)
Power Source
DC12V±10%
Power
Consumption
Operation Temp.
Storage Temp.
Weight Approximately
Dimensions
4.5W
o
o
o
o
-10 C~50C
-20 C~60C
(Max)
(Humidity : 0%RH
(Humidity : 0%RH
60%RH)
85%RH)
~
~
300g
63(H)X48(V)X114.7(D)
19
LVC-SX810HM_HP_ENG_77T
P/NO
:
3834RS0077T
7/6/06
2:51
PM
Page
20
Download PDF