LG | LV700P-D1 | LG LV700P-D1 Owner’s Manual

LV700N-D1
LV700P-D1
M
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with on wider thanthe other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong
are provided for your safety. If the provided plug
does not fit into you outlet, consult an electrician for replacement of the obsolete outlet.
Cautions for safe Operation
7
What’s in the box
8
Construction
9
Installation
10
Troubleshooting
12
OSD Menu
13
Specification
25
This camera must always be operated a DC 12V Certified/Listed, class 2
power supply only.
M3 Tapping Screws (4EA)
(Pan Lock Screw)
M3 Screw (1EA)
Revolver
Service Output
OSD Board
Holder
Base
Revolver
Revolver
Holder
1. - Use the installation label to check the
place that you wish to install.
Front
Direct Screw
Surface Mount Cable Hole
Cut Off Celing Line
Direct Screw
M4 Self Topping Screw
for Nount
P/N : MEZ57336601
Remove Dust On Celing
and Stick It
FRONT
Ceiling Mount
3
2. - Tighten the M3 Tapping Screw (A) to
fix the Ceiling Mount on the installation
label.
3. - Push the Lock Button and turn the Base Deco counterclockwise simultaneously.
- Remove the Base Deco.
4. - Loosen the Dome Frame Lock Screw
(C).
- Remove the Dome Frame.
5. - Adjust the Tilt(Up/Down) and the Pan
(Left/Right).
6. - Install the Dome Frame.
- Tighten the Dome Frame Lock Screw
(C)
4~6
Dome Frame Lock Screw(C)
7. - Install the Base Deco.
- Turn the Base Deco clockwise.
Dome Frame Lock Screw(B)
•
•
Step1
Step2
SCREW
Step3
Step4
① Pushing part of base arrow pointed turn the part B counter clock
simultaneously to remove the base deco.
② Roosen the lock screw to remove the dome cover
③ Widen the cover with both hands then remove the cover.
④ Adjust Near&Far, Wide&Tele as you wish Then install base deco,
screw, inner dome in reverse order.
Connect a DC 12V power source to the Power Input Jack of the camera as
shown below.
(Output)
*If you use the video output with service output
(jack) at the same time, it may falls off the signal output
96.5
105mm
140
LENS
MANUAL / DC
AUTO / BW / COLOR
OSD MENU - LENS
Please select the type of the lens you wish to use by pressing
the LEFT or RIGHT button.
LENS DC
LENS
DC
BRIGHTNESS
200
: RETURN
• DC/VIDEO : Auto iris lens selection
• MANUAL : Manual lens selection
• DC mode - Brightness setting(0~255 steps)
-When selecting ‘DC’ lens, the shutter speed is ‘FIXED’ mode (1/60 or 1/50)
-When selecting (MANUAL, lens, the shutter speed is ‘AUTO’)
14
LENS
DC
15
LENS
•
•
•
•
16
DC
LENS
DC
•
•
17
BLC AREA Setting
1
ALL CLEAR
ALL SET
RETURN
1 Cursor : Please select area.
- Yellow color is the selected area.
- Orange color is the nonselected area.
*Press the SETUP switch long. Enter with the sub set menu.
2 All CLEAR : Cancel the all selected area.
3 ALL SET : select all the area.
4 RETURN : Using the ‘RETURN’ key to go back to the main menu.
18
2
3
4
LENS
DC
•
•
19
LENS
•
•
20
DC
•
21
LENS
•
•
22
DC
LENS
DC
23
LENS
24
DC
LV700N-D1
Lens
LV700P-D1
2.8~12mm Vari-focal DC IRIS Lens
2000Lux (3200° K)
AUTO
OSD
COLOR/BW/AUTO
446g(With Ceiling Bracket : 90g)
Φ140(Φ140 Dome) x 105mm(Without ceiling bracket)
25
P/NO : MFL61289201
Download PDF