LG | LV903P-DB | LG LV903P-DB Owner’s Manual

Color Video Camera
Instruction Manual
Models : LV903
LV902
LV901
Before installing, operating or adjusting this
product, please read this instruction booklet
carefully and completely.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
FCC WARNING: This equipment may generate or
use radio frequency energy. Changes or modifications
to this equipment may cause harmful interference
unless the modifications are expressly approved in the
instruction manual. The user could lose the authority
to operate this equipment if an unauthorized change
or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
•
•
A suitable conduit entries, knock-outs or glands
shall be provided in the cable entries of this product in the end user.
Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
•
Holes in metal, through which insulated wires
pass, shall have smooth well rounded surfaces or
shall be provided with brushings.
Warning: Do not install this equipment in a confined
space such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with
the National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic
environment this product may cause radio interference in which case the user may be required to take
adequate measures.
Warning: To reduce a risk of fire or electric shock, do
not expose this product to rain or moisture.
Caution: This installation should be made by a qualified service person and should conform to all local
codes.
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water
(dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus.
To disconnect power from the mains, pull out the
mains cord plug. When install the product, ensure
that the plug is easily accessible.
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it means
the product is covered by the European
Directive 2002/96/EC.
2. All electrical and electronic products
should be disposed of separately from the
municipal waste stream via designated
collection facilities appointed by the government or the local authorities.
3. The correct disposal of your old appliance
will help prevent potential negative consequences for the environment and human
health.
4. For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you purchased
the product.
This product is manufactured to comply with EMC Directive 2004/108/EC and
Low Voltage Directive 2006/95/EC.
uropean representative :
E
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere, The
Netherlands
(Tel : +31-036-547-8940)
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install
in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other.
A grounding type plug has two blades and a
third grounding prong. The wide blade or the
third prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10.Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11.Only use attachments/accessories specified by
the manufacturer.
12.Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
13.Unplug this apparatus during lightning storms
or when unused for long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as powersupply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
Contents
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Cautions for Safe Operation . . . . . . . . . . . . . . . 7
Part Names and Functions . . . . . . . . . . . . . . . . 8
Reset Settings . . . . . . . . . . . . . . . . . . . . . . . . . 33
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 34
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Disassembly of the camera . . . . . . . . . . . . . . . 11
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Image Adjustment . . . . . . . . . . . . . . . . . . . . . . 13
Menu Operation . . . . . . . . . . . . . . . . . . . . . . . . 15
Camera Identification Settings . . . . . . . . . . . . 17
Exposure Settings . . . . . . . . . . . . . . . . . . . . . . 18
White Balance Settings . . . . . . . . . . . . . . . . . . 22
Day/Night Setting . . . . . . . . . . . . . . . . . . . . . . 24
Motion Detection Setting . . . . . . . . . . . . . . . . . 25
3D-DNR Setting . . . . . . . . . . . . . . . . . . . . . . . . 26
Privacy Setting . . . . . . . . . . . . . . . . . . . . . . . . 27
Special Menu Settings . . . . . . . . . . . . . . . . . . .28
Features
This color video camera is designed for use in monitoring system.
•
Day and Night Function (IR Cut Filter)
•
540 TV lines of horizontal resolution
•
Optical x2 varifocal lens
•
High sensitivity with a minimum scene illumination
of 0.0002 lux (Sens-Up, F1.2)
•
BLC covers various light conditions
•
Excellent signal-to-noise ratio of 50 dB
•
Internal / Line Lock (External)
•
Built in varifocal and DC (Auto) iris lens
•
Weather Proof: IP66 Rating (Caution: This
camera is designed for indoor installation. Do not
install it outdoors.)
•
Power Supply : Automatically switch between
DC 12 V and AC 24 V
•
Line Lock when using AC 24V.
•
Dome Cover : Vandal -Proof
Features Chart
This table shows the differences between the models.
Use LV903 is used for the description, operation and
details provided in this operating guide.
Models
LV903P-B
LV902P-B
LV901P-B
LV903N-B
LV902N-B
LV901N-B
WDR
Yes
Yes
No
Yes
Yes
No
Sens-up
Yes
No
Yes
Yes
No
Yes
HSBLC
Yes
No
Yes
Yes
No
Yes
Cautions for Safe Operation
Power Supply
Operating and storage location
This camera must always be operated a AC 24V or
DC 12V Certified/Listed, class 2 power supply only.
Avoid viewing a very bright object (such as light fittings) during an extended period. Avoid operating or
storing the unit in the following locations.
Note: Be careful of AC frequency when the camera is
operated with Line lock mode.
Handling of the unit
Be careful not to spill water or other liquids on the
unit. Be cautions not to get combustible or metallic
material inside the body. If used with foreign matter
inside, the camera is liable to fail or to get cause of
fire or electric shock.
• Remove dust or dirt on the surface of the lens with
a blower.
• Use a dry soft cloth to clean the body. If it is very
dirty, use a cloth dampened with a small quantity of
neutral detergent, then wipe dry.
• Avoid the use of volatile solvents such as thinners,
alcohol, benzene, and insecticides.
They may damage the surface finish and/or impair
the operation of the camera.
• Extremely hot or cold places (operating temperature -10°C ~ 50°C, however, we recommend that
the unit be used within a temperature range of 0°C
~ 45°C)
• Damp or dust place
• Places exposed to rain
• Places subject to strong vibration
• Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
Part Names and Functions
abc
d
a Lens
b Azimuth adjuster
Adjusts the azimuth angle to obtain a level image.
c Lens Cover Hooker
Use to separate the Lens Cover.
d Pan lock screw
Fixes the panning position after adjusting.
e Fall Prevention Wire
Fixes the wire into the dome cover.
f Video Out connector
Use this jack for checking the picture with
portable monitor when install the camera.
e
fg
g Buttons for menu
To set items on the MENU, use the these
buttons.
Part Names and Functions
h Dome Cover Ring
i Dome Cover
h
j Lens Cover
k Tilting lock screw
Fixes the tilting position after adjusting.
l Video output connector (BNC type)
i
m Power input connector
Supplies AC 24V or DC 12V from an external
power source.
j
o
k
l
p
n Camera mounting bracket
This bracket is supplied for ceiling installation.
o Focus lock lever
Fixes the focus position after adjusting.
p Zoom lock lever
Fixes the zoom position after adjusting.
m
n
Connections
Basic connection
BNC plug
AC 24V / DC 12V
cable for Camera
Video Out Connector
for installer
10
The peripheral devices (VCR, monitor, lens, etc.), AC
adapter and cables are not supplied.
1. Connecting the monitor
Make the video signal connection between the
camera and the monitor or time lapse VCR.
2. Supply AC 24V or DC 12V from an external
power source.
Disassembly of the camera
1. Remove the dome cover ring by using the bit.
2. Remove the dome cover by loosening three tamper-proof screws using the supplied bit.
11
Installation
Mounting the Camera without bracket
Mounting the Camera with bracket
This camera can be installed directly on the surface of
the wall or ceiling without bracket.
This camera can be installed on the surface of the
wall or ceiling using the supplied bracket.
Use this pad to install the
camera on the bumpy surface.
"A"
"A"
OP
EN
FR
ON
T
CLO
SE
FR
ON
T
FR
ONT
"B"
“A” Before installing the camera, make sure the
arrow marks are facing to the direction that you
desired to take a picture.
"A"
Bottom of the camera
“B” Fix the screw to fix the camera body and
bracket.
12
Image Adjustment
You can manually adjust the pan/tilt/azimuth angles,
focus, and zoom while observing the connected
monitor.
Notes:
•
Do not hold the camera by lens unit to adjust
panning, tilting, or azimuth.
•
•
•
Adjust the pan/tilt position of the camera to
face the place that you wish to watch.
Tighten the screws after adjusting.
The video output to the BNC will be interrupted
while a portable monitor is connected to the video
jack.
1. Connect a portable monitor to the video jack.
2. Adjust the pan/tilt position of the camera.
•
•
Loosen the tilting lock screw.
Loosen the pan lock screws. (1/4 turning)
13
Image Adjustment
(2)
3. Adjust the azimuth angle.
•
Release the screw (1) locking the azimuth.
•
Fix the screw locking the azimuth.
•
(3)
(1)
Rotate the lens cover (3) to obtain an angle.
4. Remove the lens cover.
Focus lock lever
•
•
Push the lens cover releaser (2).
Rotate the lens cover (3) counterclockwise.
5. Adjust the zoom
•
Unlock the zoom lever.
•
Lock the lever.
•
Move the lever to adjust the zoom.
6. Adjust the focus
•
Unlock the focus lever.
•
Lock the lever.
•
Zoom lock lever
14
Move the lever to adjust the focus.
7. Attach the lens cover.
Menu Operation
This camera utilizes an on-screen user MENU. To set
items on the menu, use the following buttons.
•
•
DOWN
SET
RIGHT
LEFT
•
UP
DOWN
RIGHT
SET
•
LEFT
UP
•
UP button:
Moves the cursor upwards. Use this button to
select an item or adjust the parameters.
DOWN button:
Moves the cursor downwards. Use this button to
select an item or adjust the parameters.
RIGHT button:
Moves the cursor to the right. Use this button to
select or adjust the parameters of the selected
item. The parameter changes each time this button is pressed.
LEFT button:
Moves the cursor to the left. Use this button to
select or adjust the parameters of the selected
item. The parameter changes each time this button is pressed.
SET button:
Executes selections and displays a submenu for
an item with the mark.
15
Menu Operation
General Operation
1. Press [SET] button.
The setup menu screen appears on the monitor.
5. Select [EXIT] option then press [SET] to exit
the setup menu. In the submenu, use [UP] or
[DOWN] button to select the [EXIT] then use
[LEFT] or [RIGHT] button to select a mode and
press [SET] to exit the setup menu.
•
•
•
2. Use [UP] or [DOWN] button to select an option
then press [SET] button.
Submenu appears on the monitor.
3. Use [UP] or [DOWN] button to select a submenu
option.
4. Use [LEFT] or [RIGHT] button to select a value.
16
RET: Return to the previous.
TOP: Return to the CAMERA SETTING
menu screen.
END: Exit the setup menu.
Camera Identification Settings
You can use the camera identification (CAMERA ID)
to assign a number to the camera.
1. Select [CAMERA ID] option on the [CAMERA
SETTING] menu.
2. Use [LEFT] or [RIGHT] to select a CAMERA ID
(OFF, 1-255).
17
Exposure Settings
You can set the exposure options using the
EXPOSURE menu.
Select [EXPOSURE] option on the [CAMERA
SETTING] menu.
WDR/BLC setting
Use WDR/BLC option to set the options for BLC or
WDR camera.
Press [SET] button and the EXPOSURE menu
appears.
1. Select [WDR/BLC] option.
2. Use [LEFT] or [RIGHT] button to select a mode
then press [SET].
•
•
18
WDR: Set the WDR limit.
- WDR LIMIT: LOW y MIDDLE y
HIGH
BLC: Set the BLC limit.
- BLC LIMIT: LOW y MIDDLE y
HIGH
Exposure Settings
•
HSBLC: Use for making objects clear and
obvious by suppressing highlight. The
HSBLC mode is automatically activated only
in low luminance scene.
-
-
-
-
Brightness setting
You can set the brightness level. (0-100)
AREA SETTING: Use [LEFT] or
[RIGHT] button to select a area then
use [UP] or [DOWN] button to select a
ON or OFF. Press [SET] to exit the Area
setting menu.
GRAY SCALE: Use [LEFT] or [RIGHT]
button to select a gray scale.
(GRAYyD.GRAYyBLACK).
USER SCALE: Use [LEFT] or [RIGHT]
button to select a bright level.(5 level)
1. Select [BRIGHTNESS] option.
2. Use [LEFT] or [RIGHT] button to set the bright
level.
MASK: Use [LEFT] or [RIGHT] button to
select [ON] or [OFF].
If you set the MASK to ON, the mask
function is activate only when the
HSBLC is automatically activated in low
luminance scene.
19
Exposure Settings
AGC (Automatic Gain Control) setting
If the images are too dark, change the maximum
[AGC] value to make the images lighter.
SHUTTER (Shutter Speed) setting
1. Select [SHUTTER] option.
1. Select [AGC] option.
2. Use [LEFT] or [RIGHT] button to select a mode.
(OFFy LOWyMIDDLEyHIGH)
20
2. Use [LEFT] or [RIGHT] button to set shutter
speed.
(AUTOy OFF y A.FLK y 1/160 ~ 1/90000
y x512~x2)
Exposure Settings
SENS-UP setting
Note:
If pictures are not clear due to darkness, use for
increase the sensitivity of picture.
If you set to one of the SHUTTER options except
AUTO on the [SHUTTER] menu, the [SENS-UP] setting is not available and [---] mark is displayed.
1. Use [UP] or [DOWN] button to select [SENS-UP]
option.
2. Use [LEFT] or [RIGHT] button to select a
[AUTO].
To setting the [AUTO] function, select the [AUTO]
on the [SHUTTER].
3. Press [SET] and use [LEFT] or [RIGHT] button
to set the SENS-UP limit (x2 ~ x128).
21
White Balance Settings
Setting the WB (White Balance) Mode
1) The color temperature is out of the 1700
- 11000K range.
You can select one of three modes for white balance
adjustment.
2) When the scene contains mostly high
color temperature objects, such as a
blue sky or sunset.
3) When the scene is dim.
•
•
1. Select [WHITE BAL] option.
2. Use [LEFT] or [RIGHT] button to select one of
three modes for white balance then press [SET].
•
22
ATW (Auto-Tracing White Balance): The
color temperature range for the proper white
balance is approximately 1700 - 11000K.
Proper white balance may not be obtained
under the following conditions:
AWCbPUSH: If you select the AWCbPUSH
mode, you will be able to set up the White
Balance automatically using [SET] button.
MANUAL: You can set the white balance
options manually.
White Balance Settings
-
-
-
COLOR TEMP: Use [LEFT] or [RIGHT]
button to select a funtion.
(INDOOR: 3200, OUTDOOR: 5100)
RED: Obtains the optimum amount of
red gain.
BLUE: Obtains the optimum amount of
blue gain.
23
Day/Night Setting
Note:
If you set the AGC to [OFF] or the SHUTTER
is set to one of the SHUTTER options except
AUTO on the [EXPOSURE] menu, the AUTO
mode of the DAY/NIGHT function is not available and [---] mark is displayed.
•
1. Select [DAY/NIGHT] option.
2. Use [LEFT] or [RIGHT] button to select mode for
day/night function.
•
AUTO: You will be able to change the Day/
Night mode automatically.
-
-
24
LEVEL: Use [LEFT] or [RIGHT] button
to select a level.
(LOWyMIDDLEyHIGH)
DWELL TIME: Use [LEFT] or [RIGHT]
button to select a dwell time. (5, 10, 15,
30, 60 sec.)
•
DAY: Color mode enabled.
NIGHT: Black-and-white mode enabled.
Motion Detection Setting
The motion detection detects the moving objects in
the scene by monitoring changes in brightness level.
You can select the level of sensitivity for motion detection to 4 zone.
5. Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
•
•
•
•
1. Select [MOTION DET] option.
HEIGHT: Enlarge or decrease the vertical
size of the mask.
WIDTH: Enlarge or decrease the horizontal
size of the mask.
MOVE X: Moves horizontal position of the
mask.
MOVE Y: Moves vertical position of the
mask.
6. Use [SENSITIVITY] option to obtain the optimum
detection level.
2. Use [LEFT] or [RIGHT] button to select a [ON]
and press [SET].
The MOTION DETECTION menu appears.
3. Use [LEFT] or [RIGHT] button to select
a zone number (AREA1 ~ AREA4) on the
[ZONE NUMBER].
4. Use [LEFT] or [RIGHT] button to set up the ON
or OFF on the ZONE STATE.
25
3D-DNR Setting
1. Select [3D-DNR] option.
If pictures are not clear due to brightness, use for
reduce the noise of picture.
2. Use [LEFT] or [RIGHT] button to select a option.
(OFFyLOWyMIDDLEyHIGH)
Notes:
•
•
26
If you set the AGC to [OFF] on the [EXPOSURE]
menu, the [3D-DNR] function is not available and
[---] mark is displayed.
When you use this function, the afterimage may
occur.
Privacy Setting
This function is aiming at the protection of personal
privacy, selecting a screen part black not to be displayed in the screen. Up to 8 zones can be registered.
3. Use [LEFT] or [RIGHT] button to select a mask
(AREA1 ~ AREA8) on the [MASK NUMBER].
4. Use [LEFT] or [RIGHT] button to set up the ON
or OFF on the DISPLAY option.
5. Use [LEFT] or [RIGHT] button to set up the
GRAY, WHITE or BLACK on the COLOR option.
6. Use [UP] or [DOWN] to select an option then use
[LEFT] or [RIGHT] button to adjust the option.
•
1. Select [PRIVACY] option.
2. Use [LEFT] or [RIGHT] button to select a [ON]
and press [SET]. The PRIVACY SETUP menu
appears.
•
•
•
HEIGHT: Enlarge or decrease the vertical
size of the mask.
WIDTH: Enlarge or decrease the horizontal
size of the mask.
MOVE Y: Moves vertical position of the
mask.
MOVE X: Moves horizontal position of the
mask.
27
Special Menu Settings
This menu lets you adjust and set up D-ZOOM,
D-EFFECT, SHARPNESS, STABILIZER, COLOR,
SYNC, USER TITLE, LANGUAGE function by yourself
in the SPECIAL menu.
1. Select [D-ZOOM] option on the [SPECIAL] menu.
1. Select [SPECIAL] option.
2. Press [SET] button and the SPECIAL menu
appears.
Setting the D-ZOOM (Digital Zoom ) level
You can select the digital zoom level.
2. Use [LEFT] or [RIGHT] button to select a [ON]
then press [SET] the DIGITAL ZOOM menu
appears. When you set to ON, the displayed
image can be shaking.
3. Use [UP] or [DOWN] to select a option then use
[LEFT] or [RIGHT] button to select a level.
-
-
-
28
ZOOM: Use [LEFT] or [RIGHT] button to
enlarge the screen.
PAN: Use [LEFT] or [RIGHT] button to move
the screen. (left or right)
TILT: Use [LEFT] or [RIGHT] button to move
the screen. (up or down)
Special Menu Settings
Setting the D-EFFECT (Digital effect)
Setting the SHARPNESS effect
You can select the digital effect.
You can select the sharpness effect.
1. Select [D-EFFECT] option on the [SPECIAL]
menu.
1. Select [SHARPNESS] option on the [SPECIAL]
menu.
2. Use [LEFT] or [RIGHT] button to select a digital
effect.
•
V-FLIP: Flip the picture vertically.
•
ROTATE: Rotate the picture. (180°)
•
•
2. Use [LEFT] or [RIGHT] button to change a adjust
the option.
MIRROR: Turn on the mirror effect.
OFF: Turn off the digital effect.
29
Special Menu Settings
Stabilizer setting
Setting the COLOR effect
You can select the color effect.
The image stabilizer function minimizes the appearance of shaky images caused by low-frequency vibration.
This function is useful for outdoor surveillance.
Select [STABILIZER] option and set to ON or OFF.
Note:
If you set the [STABILIZER] to ON, the Digital zoom is
set to [x1.1] automatically.
30
1. Select [COLOR] option on the [SPECIAL] menu.
2. Use [LEFT] or [RIGHT] button to change a color
effect.
•
•
ON: Color screen
OFF: B/W (Black and White) screen
Special Menu Settings
Setting the SYNC (Synchronization)
The SYNC function is available only with AC power
source.
1. Select [SYNC] option on the [SPECIAL] menu.
2. Use [LEFT] or [RIGHT] button to select [INT] or
[LL] (Line Lock).
•
INT: Selects for using the internal
synchronization.
-
-
Select [LL] mode and press [SET].
Select a desired phase using the [LEFT] or
[RIGHT] button.
Note:
When you use the DC 12V power, the [SYNC]
option is fixed to [INT] mode only.
•
LL (Line Lock): Selects for the operation of
multi cameras because it synchronizes the
camera phase by using the external signal
(AC power signal).
Setting the USER TITLE
You can use the camera identification to assign a
number and character to the camera (0 - 9, A-Z, a-z).
The USER TITLE is displayed on the upper left of the
screen. To disappear the user title, select [OFF].
31
Special Menu Settings
1. Select [USER TITLE] option on the [SPECIAL]
screen.
2. Use [LEFT] or [RIGHT] button to select a [ON]
then press [SET].
The USER TITLE menu appears.
-
/
: Moves cursor to left or right.
Language Setting
Select a language for the Setup menu and on-screen
display.
A
3. Use [UP], [DOWN], [LEFT] or [RIGHT] button to
select a character or number.
-
-
-
-
32
CLR: If you enter the wrong code, select
CLR then press [SET].
POS: Use [UP], [DOWN], [LEFT] or [RIGHT]
button to move position of USER TITLE on
the screen.
END: Confirm your selection.
A (Blank): Inserts a space at the cursor
position.
1. Select [LANGUAGE] option on the [SPECIAL]
screen.
2. Press [LEFT] or [RIGHT] button to select a language.
Reset Settings
•
•
CAMERA REBOOT: To reboot the camera
system.
FACTORY RESET: To reset the camera
setting to factory setting, select [FACTORY
RESET] option.
1. Select [RESET] option.
2. Press [SET] button and the RESET menu
appears.
3. Use [UP] or [DOWN] to select option.
33
Specifications
Model
Total/Effective Pixels
Pick-up Device
LV903P
470K/440K
Pixels
Lens
LV903N
410K/380K
Pixels
Iris
Resolution
S/N Ratio
Low Luminance
Video Output Signal
Auto Gain Control
34
1/3” Interline Color CCD
LV901P
470K/440K
Pixels
LV901N
410K/380K
Pixels
DC/ELC Selectable
LG XDI-s
Scanning System
Scanning Frequency
LV902N
410K/380K
Pixels
Vari-Focal Lens (f = 2.8 ~ 11mm / F = 1.2)
Signal Process
Synchronization
System
LV902P
470K/440K
Pixels
2:1 Interlace
Internal/Line Lock
50 Hz (VD)
59.94 Hz(VD) 50 Hz (VD)
59.94 Hz(VD)
540 Lines
50 Hz (VD)
More than 52 dB (AGC Off, F 1.2)
0.0002 Lux (Sens-up Auto)
0.2 Lux (AGC High, DNR)
0.2 Lux (AGC High, DNR)
0.0002 Lux (Sens-up Auto)
0.2 Lux (AGC High, DNR)
1.0 Vp-p Composite Signal (75 ohm)
OFF/LOW/MIDDLE/HIGH
59.94 Hz(VD)
Specifications
Model
LV903P
LV903N
LV902P
LV902N
LV901P
LV901N
Electric Shutter
1/50 1/90,000
(Auto Mode)
1/60 1/90,000
(Auto Mode)
1/50 1/90,000
(Auto Mode)
1/60 1/90,000
(Auto Mode)
1/50 1/90,000
(Auto Mode)
1/60 1/90,000
(Auto Mode)
Exposure
White Balance
Back Light
WDR
MOTION DET.
Power Consumption
Operation
Temperature
OFF/WDR/BLC/HSBLC
60dB
ALC/ELC
ATW / AWC->PUSH / MANUAL
OFF/WDR/BLC
60dB
OFF/ON
-
Max 3.5W
-10ºC ~ 50ºC (Humidity: 0%RH ~ 80%RH)
Storage Temperature
-20ºC ~ 60ºC (Humidity: 0%RH ~ 85%RH)
Dimension (Ø x H)
Ø140 x 110 mm
Weight
OFF/BLC/HSBLC
900g
35
P/NO : MFL62034757
Download PDF