LG | LVC-S60HP | LG LVC-S60HP Owner’s Manual

Operating Instructions
LVC-S60HM
LVC-S60HP
LVC-S60NM
LVC-S60NP
Before installing and using the camera,
please read these instructions thoroughly
and retain them for later reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK,
Warning
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet Refer servicing to qualified
personnel only.
Wiring methods shall be in accordance with the National Electric Code,
ANSI/NFPA 70.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert
the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
This symbol is intended to
alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
Regulatory Notices
For U.S.A
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation! This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
This product is manufactured to comply with the radio interference
requirements of EEC DIRECTIVE 89/336/EEC, 93/68/EEC and
73/23/EEC.
2
Contents
Features ..................................................................................................................................3
Cautions for Safe Operation ......................................................................................................4
Operating Controls and Their Functions ..............................................................................5-6
Connections .........................................................................................................................7-8
Back Focus Adjustment ..........................................................................................................9
Installation of Camera............................................................................................................10
Specifications.........................................................................................................................11
FEATURES
This color video camera is designed for use
in monitoring system.
• High resolution and high sensitivity with a
1/3 inch Super HAD CCD (Charge Coupled
Device)
• Line Lock when using AC24V power.
• CS Mount (Adapter Ring Mount for C Lens:
Optional)
• Dual power AC 24V / DC 12V
• Non-polarity DC12V
Maintence of the unit
• Remove dust or dirt on the surface of the
lens with a blower.
• Use a dry soft cloth to clean the body. If it
is very dirty, use a cloth dampended with
a small quantity of neutral detergent and
then wipe dry.
• Avoid the use of volatile solvents such as
thinners, alcohol, benzene, and
insecticides. They may damage the
surface of the body.
3
Cautions for Safe Operation
Power Supply
They must be operated with a AC 24V class 2
power supply and DC12V alternatively.
* Notes: Be careful of AC frequency when the
camera is operated with Line lock mode.
AC24V(60Hz):S60HM/S60NM
AC24V(50Hz):S60HP/S60NP
Handling of the unit
Be careful not to spill water or other liquids on the
unit. Be cautions not to get combustible or metallic
material inside the body. If used with foreign
matter inside, the camera is liable to fail or to get a
cause of fire or electric shock.
4
Operating and storage location
Avoid viewing a very bright object (such as light
fittings) during an extended period. Avoid
operating or storing the unit in the following
locations.
• Extremely hot or cold places (operating
temperature -10oC~50oC, however, we
recommend that the unit be used within a
temperature range of 0oC~45oC)
• Damp or dust place
• Places exposed to rain
• Places subject to strong vibration
• Close to generators of powerful electromagnetic
radiation such as radio or TV transmitters.
OPERATING CONTROLS AND THEIR FUNCTIONS
DC 12V
VIDEO
OUT
AES
VIDEO
DC
IRIS
POWER
PHASE
AC 24V~
1
7
1
2
3
4
5
6
4 3
2
9
5
6 8
CLASS 2
ONLY
10 12 11
Pin assignment of auto iris lens connector
3
4
1
2
Tripod adapter
CCD cover
Dip switches
Line phase adjustment volume
Lens selection switch
DC iris level adjustment volume
Pin No.
1
2
3
4
DC iris
Damping Damping +
Drive +
Drive -
Video iris
Vcc (+9V)
Not used
Video
Ground
7 Back focus lock screw
8 Auto iris lens connector
9 Back focus adjustment screw
0 Power LED
qa BNC connector for video output
qs Power input connector
5
OPERATING CONTROLS AND THEIR FUNCTIONS
➀
②
The Adjustment method of Line Lock Phase
When using a camera switcher to connect 2 cameras or
more to one monitor, there may be a vertical roll of the
images when switched. In such a case, refer to the
below.
-The vertical sync phase can be manually adjusted
within the range approximately from -90o to +90o.
- Switch the display on the monitor from camera1 to
camera2.
Adjust the PHASE volume on camera2 until the
vertical roll of the image stops.
If more than two cameras are used, please repeat this
procedure for all the cameras.
- If you can’t adjust vertical sync. phase,
Please exchange the polarity of input terminal.
➀ Camera switcher
② Monitor
➂ Vertical phase
➂
6
CONNECTIONS
DC 12V
DC12V
Power Connection
LVC-S60 (DC12V/AC24V Compatible)
1. DC 12V Power Supply
Remove the insulation on the power cable as illustrated and
connect the power cord to the AC/DC compatible terminals
on rear panel of the camera.
Note :
You don't need to be cautious of the polarity of positive
and negative.
(Auto polarity sensing)
2. AC 24V Power Supply
Connect the power cable to the AC/DC compatible input
terminal on the rear panel of the camera
AC24V
Note :
To get the optimum performance from the unit, be sure to
connect to an AC supply of 24V ±10%
AC 24V~
1
2
Connecting the monitor
➀ To VIDEO OUT
② To video input on the monitor
7
Lens Mounting
Remove the CCD cover. Then attach the CS mount lens to the camera. Please
refer to the drawing on the left. CS Mount Lens: Supplied.
C Mount Lens: You have to use the Adapter Ring Mount (not supplied).
CAUTION
Be cautious not to use Auto Iris Lens with over 30mA
DC iris level is preset in the factory. Only if necessary, adjust the DC iris level
to achieve the proper picture with AGC off.
VIDEO
AES
DC
Auto Iris Mode Selection
POSITION
DC
AES
VIDEO
* Factory Setting
8
LENS
DC iris lens
Manual or fixed iris lens
Video iris lens
No.
NAME
1 Synchronization mode
(SYNC)
2 Back light compensation
(BLC)
3 Auto gain control
(AGC)
4 Flickerless
(FL)
5 White Balance
(WB)
POSITION
L.L.
INT.
ON
OFF
ON
OFF
ON
OFF
HOLD
ATW
Set the auto iris mode selection
switch to the position that
corresponds to the lens which is
mounted to the camera. Please refer
to the table on the left.
FUNCTION
Line lock mode
Internal synchronization mode
sets to this position when strong light comes in behind the target
normal position
AGC level varies from 10dB to maximum 30dB
10dB (Max.)
shutter speed is fixed. (NTSC : 1/100 sec, PAL : 1/120 sec)
shutter speed is not fixed.
WB is fixed
tracks and adjusts WB automatically
BACK FOCUS ADJUSTMENT
If back focus has to be adjusted after mounting the lens,
1. Loosen the back focus lock screw(1) on top of the camera with a (+) screwdriver
2. Turn the back focus adjustment screw(2) on top of the camera with hands until the
desired focus is reached.
3. Tighten the back focus lock screw(1).
Note :
When tighten screw, do not inflict unreasonable force. It may damage to the unit.
(1)
(2)
9
INSTALLATION OF CAMERA
This camera is mounted with tripod which makes it possible to install from both of
the bottom and the top of the unit as illustrated.
10
Specifications
Model
Signal System
Total/Effective Pixels
Pick-Up Device
Lens
Iris Control
Signal Process
Scanning System
Sync. System
Scanning Frequency
Resolution
S/N Ratio
Standard Illuminance
Sensitivity (1/3 Output)
Video Output Signal
Back Light
Gain Control
Flickerless
White Balance
Exposure
Power Source
Power Consumption
Operation Temp.
Storage Temp.
Weight
Dimensions
LVC-S60HM
LVC-S60HP
LVC-S60NM
LVC-S60NP
NTSC
410K/380K
PAL
NTSC
PAL
470K/440K
270K/250K
320K/290K
1/3 - Inch Interline Color CCD(Super HAD)
C / CS MOUNT (Adapter Ring Mount for C Lens: Optional)
DC / AES / VIDEO
Digital Signal Process
2:1 Interlace
Internal / External (Line Lock)
Internal
59.94Hz(VD)
50Hz(VD)
59.94Hz(VD)
50Hz(VD)
More than 480Line(H)
More than 480Line(H)
More than 330Line(H)
More than 320Line(H)
More than 50 dB
2000Lux (5100°K)
0.4Lux (F1.0)
0.1Lux (F1.0)
1Vp-p Composite (75Ω)
Manual ON / OFF (with DIP Switch)
ON (Max. 30dB) / OFF (Max.10dB) (with DIP Switch)
ON / OFF (with DIP Switch)
ATW / HOLD (with DIP Switch)
Automatic control with DC Iris meter / Video Iris meter / Auto Electronic Shutter (Max. 1/100000)
DC 12V ± 10% (Auto Polarity Sensing) / AC 24V ± 10%
3.5W
-10oC ~ 50 oC (Humidity : 0%RH ~ 60%RH)
-20 oC ~ 60 oC (Humidity : 0%RH ~ 85%RH)
Approximately 300g
55 (H) X 56 (V) X 123 (D)
11
P/NO.: 3834RC0022Q
Download PDF

advertising