LG | LVS201 | LG LVS201 Owner’s Manual

OWNER'S MANUAL
LVS201
Please read this manual carefully before operating
your set and retain it for future reference.
P/NO : MFL62591982
1011 (V2.0)
2
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the user
to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
FCC WARNING: This equipment may generate or use radio frequency
energy. Changes or modifications to this equipment may cause harmful
interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
3
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
• A suitable conduit entries, knock-outs or glands shall be provided in
the cable entries of this product in the end user.
• Caution: Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended
by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
• Holes in metal, through which insulated wires pass, shall have smooth
well rounded surfaces or shall be provided with brushings.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB003 du Canada.
Warning: Do not install this equipment in a confined space such as a
bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the National
Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to
take adequate measures.
4
Warning: To reduce a risk of fire or electric shock, do not expose this
product to rain or moisture.
Caution: This installation should be made by a qualified service person
and should conform to all local codes.
Caution: To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water (dripping or
splashing) and no objects filled with liquids, such as vases, shall be placed
on the apparatus.
To disconnect power from mains, pull out the mains cord plug. When
installing the product, ensure that the plug is easily accessible.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
5
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.
6
LG Electronics hereby declares that this/these
product(s) is/are in compliance with the essential
requirements and other relevant provisions of
Directive 2004/108/EC, 2006/95/EC, and 2009/125/
EC.
European representative :
LG Electronics Service Europe B.V. Veluwezoom 15,
1327
AE Almere. The Netherlands
(Tel : +31-(0)36-547-8888)
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is
attached to a product it means the product is
covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should
be disposed of separately from the municipal
waste stream via designated collection facilities
appointed by the government or the local
authorities.
3. The correct disposal of your old appliance will
help prevent potential negative consequences
for the environment and human health.
4. For more detailed information about disposal
of your old appliance, please contact your city
office, waste disposal service or the shop where
you purchased the product.
EEE Compliance with Directive. (for Turkey only)
7
Cautions for Safe Operation
Handling of the unit
Be careful not to spill water or other liquids on the unit. Be cautious not to
get combustible or metallic material inside the body. If used with foreign
matter inside, the device is liable to fail or to get cause of fire or electric
shock.
• Use a dry soft cloth to clean the body. If it is very dirty, use a cloth
dampened with a small quantity of neutral detergent then wipe dry.
• Avoid the use of volatile solvents such as thinners, alcohol, benzene
and insecticides.
They may damage the surface finish and/or impair the operation of the
device.
Operating and storage location
Avoid viewing a very bright object (such as light fittings) during an
extended period. Avoid operating or storing the unit in the following
locations.
• Extremely hot or cold places (operating temperature from -10 °C
to 50 °C, however, we recommend that the unit be used within a
temperature range from 0 °C to 45 °C)
• Damp or dust place
• Places exposed to rain
• Places subject to strong vibration
• Close to generators of powerful electromagnetic radiation such as
radio or TV transmitters.
8
Contents
10
10
Preparation
Introduction
10
Features
10
Supplied Accessories
11
13
Rear Panel
Installation
13
Precautions
13
Connecting Camera
14
Connecting Network
15
Connecting RS-485 Device
15
Connecting Power Source
15
To use the power adapter
16
To use the PoE (Power over Ethernet)
device
17
18
Wall Mounting
Operation
9
18
Before using the system
18
Recommended PC Requirements
19
Accessing the LG IP device
21
LG Smart Web Viewer Overview
24
Configuring the LG video server
24
Accessing the Configuration menu
24
Configuration menu overview
25
System settings
29
Audio & Video settings
32
PTZ protocol
38
Network settings
44
User settings
48
Event settings
52
Troubleshooting
56
Appendix
56
Open source software notice
59
Specification
10
Preparation
Introduction
The LG Video Server is designed to use on an Ethernet network and must
be assigned an IP address to make it accessible. This manual contains
instructions on how to install and manage the Video Server in your
networking environment. Some knowledge of networking environments
would be beneficial to the reader.
Should you require any technical assistance, please contact authorized
service center.
Features
The LG Video Server offers the following functions:
•
Dual H.264 Stream for single Video Input
•
Multi-Codec (H.264, MJPEG) Streaming
•
PoE (Power over Ethernet) Support (802.3af )
•
2 Power (DC 12 V, PoE) Support
•
Pre/Post Alarm Support
•
Remote Pan/Tilt/Zoom Control (RS-485 support)
Supplied Accessories
•
Mounting bracket
•
Program CD
•
Owner’s Manual
11
Rear Panel
a
bcd e
a ETHERNET/POE Port
Connects to a PC or a network via a hub with a 10 BASE-T/100 BASETX cable attached RJ-45 connector.
Note:
Power over Ethernet (PoE) is a technology that integrates power into
a standard LAN infrastructure. It enables power to be provided to the
network device, such as a network camera, using the same cable as
that used for network connection. It eliminates the need for power
outlets at the device locations and enables easier application of
uninterruptible power supplies (UPS).
12
b RESET button
Push the button more than 3 seconds, this would restore the factory
default settings.
c Power indicator
Lights when the camera is powered.
d VIDEO INPUT
Connect the camera’s video output to this BNC connector.
e External device connectors
• RS-485 Terminals: Connect RS-485 compatible device.
•
Power input terminal: Connects to a DC 12 V power supply using
proper cables.
Installation
Precautions
•
Be sure to switch off the unit before installation and connection.
•
The installation should be made by qualified service personnel or
system installers.
•
Do not expose the power and connection cables to moisture, which
may cause damage to the unit.
Connecting Camera
Connect the video output of your camera to the LG Video Server, using a
standard 75 Ω video coaxial cable with BNC connector.
13
14
Connecting Network
You can control and monitor the system via network. With the remote
control (monitoring), you can change the system configuration or monitor
the image via network. After the installation, check the network settings
for the remote control and monitoring work.
Connect the LG Video Server to your network using a standard RJ-45
network cable as shown below.
Router
PoE Device
(IEEE802.3af )
Broadband
Service
Broadband
Service
15
Connecting RS-485 Device
Use these ports to connect PTZ Device or an external device of RS-485
format.
Note:
Do not use the multiple RS-485 device to connect the unit, it may cause
the malfunction.
TRX+
TRX-
RS-485 device
Connecting Power Source
Connect power, using one of the methods listed below:
To use the power adapter
Connect a DC 12 V power source to the power input terminal as shown
below.
1. Remove the insulation on the power cable as illustrated. (a)
2. Connect to the DC 12 V UL Listed, Class 2 Power Supply only on the
unit.
16
To use the PoE (Power over Ethernet) device
Connect the PoE cable to the LAN port on the unit. You must use the
“IEEE802.3af” standard PoE device.
PoE Device
(IEEE802.3af )
Note:
If the camera doesn’t work properly after connect PoE device, please
check if the PoE device is supplying enough power.
Wall Mounting
The LG Video Server is supplied with a mounting bracket for wall
mounting. The mounting bracket can be positioned for mounting the
video server on a vertical surface. Follow the instructions below to attach
the brackets to the video server:
1. Install the mounting bracket to the wall with four screws.
2. Assemble the LG Video Server and mounting bracket. (Connect the
unit by following step a and b.)
3. Connect the cables to the terminals on the LG Video Server.
17
18
Operation
Before using the system
•
•
•
•
•
•
•
Before using the LG IP device make sure the connections are correct
and verify whether proper power supply is used.
Check the connections of the LG IP device for the correct conditions.
Check that the LG IP device is(are) connected to the network and that
power is supplied.
Once the connections are made you need to install the LG client
program to the PC from which you want to access the device. The
LG Smart Web Viewer program is automatically installed when you
connect the LG IP device.
The LG Smart Station and the LG Smart Web Viewer program are the
network program of the LG Video Server and the LG IP cameras.
To view streaming video in Internet Explorer, set your browser to allow
ActiveX controls. If you find this message “This website wants to install
the following add-on: ‘IPCam_Streamer.cab’ from ‘LG ELECTRONICS
INC’”, Click the yellow bar and install LG Smart Web Viewer Program on
your computer.
The Layouts and the Live view pages may differ with different OS
(Operating Systems) and Web Browsers.
Care needs to be taken not to run any other applications when the
Client Program is running as it may cause memory shortage.
Recommended PC Requirements
The LG IP device can be used with most standard operating systems and
browsers.
19
Items
Operating System
Requirements
Windows XP Professional
CPU
Intel Core2 Quard Q6700 (2.66 GHz)
Web Browser
Microsoft Internet Explorer 6.0 or 7.0
DirectX
DirectX 9.0 or above
Memory
2 GB or above RAM
Graphics Card
Resolution
256 MB or above Video RAM
1 280 x1 024 (with 32 bit color) or higher
Accessing the LG IP device
You can access the LG IP device by following the below steps.
1. Copy the IP Utility to your PC
1.1 Insert the Client Program CD.
1.2 Find and Copy IP Utility folder to your PC.
2. Discover LG IP device using the IP Utility
The IP Utility can automatically discover and display LG IP devices on
your network. The IP Utility shows the MAC address, IP address, Model
name and so on.
Note:
The computer running the IP Utility must be on the same network
segment (physical subnet) as the LG IP device.
2.1 Run the IP Utility program.
20
2.2 Click the [Search] icon or select the [Search] option in the Device
search menu.
After a few seconds the found LG IP devices will be displayed in
the IP Utility window.
3. Logging in to the LG Smart Web Viewer
The LG Smart Web Viewer can be used with most web browsers. The
recommended browser is Internet Explorer with Windows.
3.1 Run the IP Utility and find the LG IP devices.
3.2 When the LG IP devices appear in the IP Utility window, doubleclick IP address or right click on the same IP address and select
“Connect to Web Page” to start the LG Smart Web Viewer. When
accessing the LG Smart Web Viewer, the authentication dialog
appears on the screen.
3.3 Enter the user name and password. (Note that the default
administrator user name and password are “admin”.)
3.4 Click the [OK] button and then the LG Smart Web Viewer is
displayed in your browser.
Notes:
•
You can also access the LG Smart Web Viewer as shown below.
3.1 Start your Web browser.
3.2 Enter the IP address of the LG IP device in the address bar of
the browse.
3.3 Enter the user name and password set by the administrator.
3.4 Click the [OK] button and then the LG Smart Web Viewer is
displayed in your browser.
•
The LG Smart Web Viewer needs more time to display it according
to the network conditions.
21
•
If the login window is not displayed, check the pop-up blocker.
If you set the pop-up blocker, the login window is not displayed.
You must allow the pop-ups.
•
If you connect the LG Smart Web Viewer for the first time, the
Security Warning window is displayed to install the LG Smart
Web Viewer program. You must install the LG Smart Web Viewer
program for using the LG IP device.
•
If your computer or network is protected by a proxy or firewall, the
proxy or firewall settings can prevent the LG Smart Web Viewer
program. Change the proxy or firewall settings to activate the LG
Smart Web Viewer program.
LG Smart Web Viewer Overview
22
Item
Description
Select the video image size from the dropdown list. (AUTO, D1 or CIF)
The initial view size is set to AUTO. The AUTO
option sets the view size according to the
Server’s resolution.
Displays the current video codec of the
selected video stream (Master or Slave).
Check this option as the network connection
type (TCP or UDP). If you check it, the client
connects to the server using TCP connection.
Click to save the current image in JPEG format
on your computer.
1. Click the [Snapshot] button and then the
Snapshot window is displayed.
2. Click the [Save] button in the Snapshot
window.
3. Enter the file name (JPEG format) and
select the folder to save it.
4. Click the [Save] button to confirm it.
5. Click the [Close] button in the Snapshot
window to close it.
Displays the Camera OSD control window.
Use these buttons to setup the Camera. This
button does not appear on the screen if the
login is other than the administrator.
Displays the PTZ control window. Use these
buttons to control the PTZ unit.
This button is not displayed with normal or
anonymous user.
23
Select the video stream. From the Live view
drop-down list, select the desired video image
source between [Master-0] and [Slave-0].
Note:
Master and Slave are output video streams.
You can set the stream configurations
independently for either Master or Slave
stream. This would facilitate the user to set the
live view at his comfort.
Provides all the necessary tools for setting up
the device to your requirements. The user will
need administrator level to do this.
Note:
If you want to exit the Configuration menu,
select one of the video stream in the Live view
drop-down list.
Displays the current surveillance live screen.
You can monitor the camera image on the live
view window of the LG Smart Web Viewer.
24
Configuring the LG video server
The features and options of the LG video server are configured
through the Configuration menu.
Only administrator-level users have permission to access the Configuration
menu.
Accessing the Configuration menu
Click the [Configuration] button to display the LG Smart Web Viewer
configuration window.
Warning
The Configuration setup should be made by qualified service personnel or
system installers.
Configuration menu overview
The following table shows the list of menu items.
Main Menu
Sub Menu
Version
Date & Time
System
Maintenance
Log & Report
Language
Camera
Stream
Audio & Video
PTZ protocol
Preset
Motion detect
25
Basic
RTP stream
Network
TCP/IP
DDNS
IP filtering
User
Event
Basic
Event schedule
Event server
System settings
Version
Displays the current version of Firmware, Hardware, Software and Web
Client.
26
Date & Time
Time zone
Set the time difference from GMT in the area where the IP device is
installed.
Select the time zone in the area where the IP device is installed from the
drop down list.
Time mode
•
Synchronize with NTP Server: Select if you want to synchronize the
IP device’s date and time with those of the time server called NTP
(Network Time Protocol). Specify the NTP server’s name. Click the
[Test] button for connection test to the server.
•
Synchronize with personal computer: Select if you want to
synchronize the IP device’s date and time with your computer.
•
Synchronize manually: Select if you want to set the IP device’s date
and time manually. Select the year, month and date by clicking the
calendar button. Set hour, minutes and seconds in the edit boxes.
27
Server time
•
Server time: Displays the current date and time of the IP device.
•
Save: Click this button to confirm the settings.
Maintenance
System reboot
Click the [Reboot] button to restart the IP device. It takes some minutes for
the IP device to start again.
Restore and backup
•
Backup: To take a backup all of the settings. If necessary, it make
possible to return to a backuped configuration. Click this button and
follow the instructions on the browser to specify the folder and save
the setting data of the IP device. This configuration backup can be
restored whenever needed.
•
Restore: Click the [Browse] button and select the file in which the
configuration setting data is stored and click the [Upload] button.
Click the [Restore] button after successfully uploading the backup
configuration. The System settings will be restored to the uploaded
configuration except network settings, and reboot the system.
28
Notes:
•
Backup and Restore can happen on IP device having the same
version of firmware. This feature is not intended for multiconfigurations or for firmware upgrades.
•
[Backup] function is allowed in HTTP protocol but not in HTTPS
protocol.
Firmware
•
Upgrade
1. Click the [Browse] button
2. Find and open the firmware file.
3. Click the [Upload] button.
4. Click the [Upgrade] button to update the firmware.
•
Initialize: The [Initialize] button should be used with caution. Clicking
it will return all of the IP device’s settings to the factory default values.
(Except for Network settings, PTZ Protocol and Preset settings.)
Log & Report
Log & Report status
The System log provides a summary of the status of the IP device. The unit
records the data of the software activity in a file.
•
View Log: Click this button to display the system log information.
•
View report: Click this button to display the report window of the
system.
29
Language
Language list
Select a language for the LG Smart Web Viewer configuration menu and
information display.
•
Save: Click this button to confirm the settings.
Audio & Video settings
Camera
30
Preview
You can preview the camera image on the preview window.
General
•
Contrast: Edit the contrast value from 0 to 100. Selecting 100 provides
the image with the highest contrast.
•
Brightness: Edit the brightness of the camera. It is brighter when a
large value is selected and it is darker when a small value is selected.
•
Standard: Displays the video standard of the camera.
•
Hue: Edit the video Hue of the camera from 0 to100.
•
Save: Click this button to confirm the settings.
•
Default: Click this button to restore the IP device back to original
factory settings.
Stream
31
Master/Slave
•
Enable: Click to activate the stream function.
•
Video codec: Select the video mode (Codec) from the drop-down list.
The viewer can choose between MJPEG and H.264.
•
Resolution: Select the image size to be sent from the camera.
•
•
NTSC:
D1 (704 x 480), HALF D1 (704 x 240), CIF (352 x 240)
and QCIF (160 x 112)
PAL:
D1 (704 x 576), HALF D1 (704 x 288), CIF (352 x 288)
and QCIF (160 x 144)
Maximum frame rate: Set the frame rate of the image. Selectable
values of the frame rates are as follows.
NTSC:
1 to 30 (fps)
PAL:
1 to 25 (fps)
Quality: Select the Quality.
--
VBR: The bit rate may vary depending on the complexity of the
video to meet the selected quality.
--
CBR: The video quality may vary in order to preserve a constant bit
rate.
•
Stream quality: If the [Quality] option set to VBR, this option is
displayed. Select the stream quality from the drop down box, the
camera supports five types (Highest, High, Medium, Low and Lowest)
•
Bit rate: If the [Quality] option set to CBR, this option is displayed. Edit
the bit rate value from 256 to 10 240 kbps.
•
Save: Click this button to confirm the settings.
32
PTZ protocol
Allows the user to configure different PTZ controls by using different PTZ
protocols.
PTZ protocol list
•
PTZ protocol: Displays the selected PTZ protocol.
•
Edit: Click to display the PTZ protocol window. Select a PTZ protocol
and then click the [Save] button. If you want to delete the protocol,
click the [Remove] button.
Upload PTZ protocol
Follow the instructions below to upload PTZ protocol.
1. Click the [Browse] button, find and open the file and then click
[Upload] button.
2. Click the [Add PTZ protocol] button and then the PTZ protocol will be
added.
PTZ configuration
•
Enable: Click to use the PTZ protocol.
33
•
Camera ID: Enter the PTZ device ID. Make the same ID as the PTZ
Device.
•
Pan speed: Enter the panning speed of the PTZ device in the edit box.
Default value for the LG Multix Protocol is 60 and ranges from 0 to 127.
•
Tilt speed: Enter the tilting speed of the PTZ device in the edit box.
Default value for the LG Multix Protocol is 60 and ranges from 0 to
127.
•
Zoom speed: Enter the zoom speed of the PTZ device to view the
object close or at a distance. Default value for the LG Multix protocol is
1 and ranges from 0 to 3.
•
Focus speed: Enter the focus speed of the PTZ device to focus an near
or far object clearly. Default value for the LG Multix protocol is 1 and
ranges from 1 to 3.
•
Preset tour park time: Enter the parking time.
Port
•
Baud rate: Select the desired speed of communication between the IP
device and the PTZ Device. Confirm selected parameter to the baud
rate of the IP device.
•
Data bit: Set the number of the data bits for RS-485 communication.
•
Parity: Select the desired parameter. The parity bit, added to the data,
to perform parity check.
•
Stop bit: Enter the desired parameter. The stop bit, added to the last of
data, in asynchronous communication.
•
Save: Click this button to confirm the settings.
34
Preset
Preview
You can see the settings screen from the preview window.
1. Move the camera to the point you want by using the arrow buttons.
2. Adjust the zoom, focus or iris options.
3. Set the Pan, Tilt, Zoom or Focus speed options.
4. Click the [Save] button to confirm the settings.
Pattern
You can activate the camera in a repeating pattern. The pattern is
programmed by recording your manual pan, tilt, and zoom operations.
The camera stores the movements you performed in memory.
•
To record the pattern
1. Click the [Start recording] button to start the pattern recording.
2. Move the camera through the desired movement.
35
3. Click the [Stop recording] button to stop the pattern recording.
Note:
The available total time of pattern differs depending on connected
PTZ device and operation.
•
To play the pattern
1. Click the [Play] button to play the programmed pattern.
2. Click the [Stop] button to stop playing.
Preset
Displays the registered preset position.
•
Add: Click to add the preset position.
1. Click the [Add] button.
2. Select the preset index number.
3. Enter the preset alias.
4. Click the [Save] button.
5. Repeat the steps 1 to 4 to add other positions.
Note:
If you set the HOME position, check the [Set home position] option.
•
Remove: Click to delete the preset position.
1. Select the preset from the list.
2. Click the [Remove] button. The preset will be deleted.
•
Go to preset: Move to the preset position.
1. Select the preset from the list.
36
2. Click the [Go to preset]. The camera will be moved to the selected
preset.
Preset tour
A preset tour is composed of a group of preset positions that the operator
can link together in a sequence.
•
To tour the preset positions
1. Choose the preset in the [Preset].
2. Click the [Add] button in the [Preset tour].
3. Repeat the steps 1 to 2 to add another preset.
4. Click the [Save] button to confirm the preset tour.
5. Click the [Play] button to start the preset tour.
6. Click the [Stop] button to stop the preset tour.
Note:
If you control the PTZ or OSD, the preset tour will be stopped.
•
Remove: Click this button to delete the selected preset in the [Preset
tour list].
37
Motion detect
Preview
You can preview the motion detection window on the preview window.
General
•
Sensitivity: Enter the sensitivity to detect an object in motion.
•
Save: Click this button to confirm the settings.
How to set the motion detection window
1. Click the [Add] button. The motion detection window is displayed. You
can add the five windows maximum for motion detection area.
2. Set the [Sensitivity] option.
3. Click the [Save] button to save the settings.
4. Click the edge or coner of the window box to adjust the window size
for motion detection.
38
Notes:
•
You can reset the window size. Click one of the window edge or
coner and drag & drop to reset the motion detection area.
•
Motion detection function is available for H.264 codec.
Network settings
Basic
General
•
MAC address: Displays the MAC address.
Port & Encryption
•
Web port: The default HTTP port number (80) can be changed to any
port within the range 1 025 to 65 535.
•
RTSP port: Check RTSP port. The default port is 554. Other ports can
be selected within the range 1 025 to 65 535.
•
Network encryption: Select the HTTP or HTTPS option for security.
39
Note:
The RTSP port number should not be same with the web port
number.
TTL
•
TTL: This option indicates the Time-To-Live of multicast packets. The
default setting is 7, and the allowed TTL range is 1 to 255.
ARP Ping
•
Enable ARP Ping to configure IP address: Check to enable ARP ping.
•
Save: Click this button to confirm the settings.
RTP stream
RTP (Real-time Transport Protocol) is an internet protocol that allows
programs to manage the real-time transmission of multimedia data, via
unicast or multicast.
40
Master / Slave
•
RTP unicast: When enabled the transmission of the data to the
specified equipment happens on a network specifying a single
address.
•
RTP multicast: When enabled it reduces the transmission load on
the camera by making the computer of the same segment network
receive the same transmission data. When multicast option is checked
then select Video Port number, Audio Port number and Data port
number.
--
Video RTP port: Specify the video transmission port number used
for the multicast streaming. It is initially set to 8 888 and you can
edit this between 1 025 and 65 534.
--
Audio RTP port: Specify the audio port number used for the
multicast streaming. It is initially set to 7 777 and you can edit this
between 1 025 and 65 534.
--
Data RTP port: Specify the VA data port number used for the
multicast streaming. It is initially set to 6 666 and you can edit this
between 1 025 and 65 534.
--
IP address: Set the IP address for RTP multicast.
Note:
Each stream using multicast needs its own a pair of multicast IP
address and port numbers to avoid address conflict.
•
Save: Click this button to confirm the settings.
41
TCP/IP
IP address status
•
Automatically set with DHCP: Select this option when a DHCP server
is installed on the network to allow IP address assignment. With this
setting, the IP address is assigned automatically.
--
Notify to SMTP server, if IP address is changed: If you select this
option, the user get a notification mail telling about changing of
IP of the IP device.
Note:
You should register the SMTP server on the Event server setting to set
this function.
•
Statically set: Select this option when you set a fixed IP address, with
this setting, specify the IP address, Subnet mask and default gateway
manually.
--
IP address: Enter an IP address.
--
Subnet mask: Enter a subnet mask address.
--
Gateway: Enter the gateway address.
42
DNS server status
•
DNS server: Enter the Primary domain name server that translates the
hostnames into IP address.
•
Secondary DNS server: Enter the Secondary DNS server address that
backups the Primary DNS.
•
Save: Click this button to confirm the settings.
DDNS
This free service is very useful when combined with the LG DDNS Server.
It allows the user to connect the IP device using the URL, rather than an IP
address. This also solves the problem of having a dynamic IP address.
DDNS status
•
Don’t use DDNS server: Disable the DDNS function.
•
Use DDNS server: Enable the DDNS function.
•
--
Provider: Displays the DDNS provider.
--
Hostname: Enter the hostname you want to use.
Save: Click this button to confirm the settings.
43
IP filtering
The access of the IP addresses in the list are allowed or denied according
to the choice made in the drop-down list of the Basic policy option. The
administrator can add up to 10 IP address entries to the list (a single entry
can contain multiple IP addresses). The users from these IP addresses need
to be specified in the user list with the appropriate access rights. The IP
list is to control the access permission of clients by checking the client IP
address.
IP list
•
Basic policy: Select the basic policy type.
--
Allow all: Allow all the IP address basically, but the IP addresses in
the list are denied.
--
Deny all: Deny all the IP address basically, but the IP addresses in
the list are allowed. It needs at least one IP address to activate this
function.
•
Save: Click this button to confirm the settings.
•
Add: Click this button to add the IP address.
1. Click the [Add] button.
44
2. Set the IP options.
--
Alias: Enter the alias.
--
From: Enter the start IP address for the IP filtering.
--
To: Enter the end IP address for the IP filtering.
Note:
If you want to deny or to allow a range of IP addresses, enter the start
IP address to “From” and the end IP address to “To”. You can also add an
IP address by entering the same IP address to “From” and “To”.
3. Click the [Save] button.
4. Repeat the steps 1 to 3 to add additional IP address.
•
Remove: Click this button to delete the IP address.
1. Select the alias from the list.
2. Click the [Remove] button. The IP address will be deleted.
User settings
Basic
The default user ID of this IP device are [admin] (Administrator) and
[anonymous] (Custom user).
If your user ID is registered as an administrator, you can register a new user
and provide the access rights for each user. A maximum of 50 users can be
created.
45
User list
•
Add the User
You can register a new user with various access rights.
1. Click the [Add] button. User setting dialog is displayed.
2. Enter the new User ID and Password. (Should have a minimum of
4 characters and preferably a combination of alphanumeric).
3. To confirm the password, retype the password that you typed in
the Password box.
4. Select the authority from the drop down list to provide the access
rights to each user and then click the [Save] to confirm your
selection.
--
Administrator: Allows you to operate setup menus and to
view live images.
--
Power user: Use of the limited functions of the system (The
Configuration menu is not allowed). A power user can use the
Live View, PTZ control, OSD control and audio functions.
46
--
Normal user: Provides the lowest level of access. Allows to
view live images only.
--
Custom user: The user can login and view the live stream
image only when the “Enable anonymous login” option is
checked to enable it.
Note:
Remember the password.
•
Edit the registered user
You can change the password or authority.
1. Choose the user ID and then click the [Edit] button.
2. Change the Password or Authority, then click the [Save] button to
confirm your selection.
•
Delete the registered user
1. Choose the user ID you want to delete.
2. Click the [Remove] button.
Note:
The default administrator user ID ‘admin’ is permanent and cannot be
deleted.
Anonymous
•
Enable anonymous login
Check the box to enable anonymous user login - allows the user
access for only viewing the live stream image.
Maximum RTP stream connection
•
Maximum number of simultaneous stream connection:
Set this number to limit the number of simultaneous stream
connections.
The connections depend on the stream configuration as shown in the
following Maximum RTP stream connection by stream configuration.
47
Video Codec Resolution
Frame Rate
(NTSC)
Quality
Maximum
RTP stream
H.264
D1
30
HIGHEST
Up to 5
H.264
D1
30
MEDIUM
Up to 10
MJPEG
D1
30
MEDIUM
Up to 1
MJPEG
Half D1
30
MEDIUM
Up to 2
MJPEG
D1
15
MEDIUM
Up to 10
Note:
Preview window of the IP device setting and preset setting are
affected by this setting.
•
Save: Click this button to confirm the settings.
48
Event settings
Event schedule
When the Motion detection event occurs, this unit records the live images
and routes as configured.
To edit the Event Schedule
1. Click the [Edit] button. Event schedule window is displayed.
2. Set the options.
•
Trigger: Displays the selected trigger event.
•
Time: Sets the weekday, Start, Finish, Pre alarm, Post alarm and
Ignore interval time options.
•
Action: Selects the options. This occurs when the event runs.
--
FTP server/SMTP server: Uploading of images to an FTP server,
or e-mail notification.
•
Stream: Selects the stream of the connected camera.
•
Default: Sets to default setting value.
3. Click the [Save] button to confirm the settings.
Note:
You should register the SMTP and FTP server on the Event server setting to
set this function.
49
Event Server
Event Servers are used to receive the recorded video clip and/or
notification messages.
FTP server list
Image files can be transferred to the FTP server depending on the event
schedule. Image file that has been recorded for an external event is sent
to the FTP server.
To add the FTP server
1. Click the [Add] button. FTP server setting window is displayed.
2. Set the FTP server options.
•
Alias: Type the FTP Server name to upload the image files.
•
Address: Enter the FTP server’s IP address.
•
Port: Enter the port number. The default FTP port is 21.
•
User ID: Type the user name for the Folder shared in the FTP
server.
•
Password: Type the password for the folder shared in the FTP
Server.
50
•
Folder: Type the path with the folder that is shared in the FTP
server.
•
Test: Select [Test] to test the FTP server.
3. Click the [Save] button to confirm the settings.
To edit the FTP server
1. Choose the FTP server in the FTP server list.
2. Click the [Edit] button.
You can check or edit the FTP server options.
To delete the FTP server
1. Choose the FTP server in the FTP server list.
2. Click the [Remove] button. This would remove the FTP server from the
list.
SMTP server list
By selecting the e-mail option, a still image of the event is captured and
an e-mail with the attached image file is sent to the specified mail address.
To add the SMTP server
1. Click the [Add] button. SMTP server setting window is displayed.
2. Set the SMTP server options.
•
Alias: Enter the SMTP server name.
•
User ID: Enter the user ID of the SMTP server. This would be the
one who owns the mail account.
--
Password: Enter the password of the SMTP server.
--
Address: Enter the SMTP server address.
--
Port: Enter the port number. The default port is 25.
--
Enable SSL: Check when use the SSL (Secure Socket Layer)
protocol. SSL protocol is cryptographic protocols that provide
secure communication on a network.
51
--
Receiving address: Type the recipients e-mail address. You can
specify only one recipient e-mail address.
--
Administrator address: Type the e-mail address of the
administrator.
--
Subject: Enter the subject/title of the e-mail.
--
Message: This message can describe the information of the
acquired IP address, etc.
--
Test: Select [Test] to test the SMTP server.
3. Click the [Save] button to confirm the settings.
To edit the SMTP server
1. Choose the SMTP server in the SMTP server list.
2. Click the [Edit] button.
You can check or edit the SMTP server options.
To delete the SMTP server
1. Choose the SMTP server in the SMTP server list.
2. Click the [Remove] button.
52
Troubleshooting
This section provides useful information to help you to resolve any
difficulty you might have with your LG IP device. Fault symptoms, possible
causes and remedial actions are provided here.
IP Setting problems
•
ARP/Ping: Disconnect and reconnect the power to the network
camera. The device should get the IP within 2 minutes.
•
Ping your camera: Open the command prompt on your computer,
type ping with the IP address of the network device. The reply
obtained by this command provides explanation for the cause of the
problem.
1. bytes = 32 time = 2 ms indicates that the IP address is already
used and cannot reuse the same. A new IP address needs to be
obtained.
2. Destination host unreachable: indicates that the network device
and your computer do not fall in the same subnet hence needs
to get a new IP address. Contact the system administrator for the
required help.
3. Request timed out: Indicates that the IP is free as it is not used by
anyone and the network device can obtain this.
•
IP Conflicts: The other device may use th same IP address with the
LG IP device. Refer ‘Ping your camera’ to check the conflict and then
contact the system administrator for the required help.
Cannot access the camera from browser:
•
Reconnect the network camera with power and check the ping
operation to know if the IP is used by others.
•
Disable the proxy setting in the Browser if you are using a proxy server.
•
Check for proper cabling and network connections, try to ping after
verifying the connectivity.
•
Sometimes when HTTPS is enabled, we would be checking the URL
with http, in this case manually change the URL to the http/https
accordingly.
•
Verify the DNS and Gateway settings if the IP address is assigned
statically to the network device.
•
When the web page loading is failed or very slow, Check the
streaming configuration. Use H.264 codec and change frame rate,
stream quality, resolution setting.
•
If you have error at web client live view page, close browser, delete
below directory and re-connect the camera.
ex) “C:\Documents and Settings\[UserID]\WebClient”.
Accessing camera external to the local network
•
Firewall Protection: Check for the internet firewall with the system
administrator, either he has to do port forwarding or modify the DMZ
function on the router.
•
Default router needed: Check if you need configure the router
settings.
Sporadic network performance
•
Network Switches or hubs used may be of the lower configuration
and the load on this may not meet the required conditions of our
network camera.
53
54
•
Check for the RJ45 cables that are used for the network connectivity.
•
If POE is used check if the power is got by the network camera when
connected to it.
Login Password lost
•
Reset the camera by pressing the Reset button for more than 3
seconds to restore default settings.
•
After the factory settings login using the default username and
password.
Video Streaming problems
•
If the video streaming does not start on the Web browser, install the
LG Web Client ActiveX program on your computer following the
instructions on the Web browser.
•
When Windows IE browsers are used always take care to allow pop
ups, check this option before we run the web client.
•
Check the quality of image by referring the video settings as
described in the manual.
•
Sometimes there would be intermittent or very slow video streaming,
this may be because of the higher resolution and frame rate that are
set for the video.
•
The video streaming may appear poor at times, this may be because
of the network traffic ,too many devices connected to the switch or
hub, enabling motion detection to each of the video streams and
because of other programs running on your computer.
•
If the images appear to be blurred adjust the focus of the network
camera to get a clear image.
•
If video images appear white and black adjust the settings in the OSD
to get back the colorful image.
55
•
Select the Night mode if the network camera is connected at a place
where surrounding light is less or dark.
•
If we obtain lower frame rate than set we need to check from the
system administrator for sufficient bandwidth available or reduce the
number of applications running on the client computer.
•
If the client PC’s are unable to access the multicast stream, check with
the system administrator for the use of a valid multicast address or
check if the router is supporting multicasting.
•
If the images appear to have white of gray stripes on it, upgrade the
Video graphics driver on the client PC to the latest version.
•
Video images may be noisy if you are using the camera in a very low
light environment or the bit rate/quality is set to very low values.
Provide higher values for quality and support the surrounding
environment with enough light.
For all further support please contact the supplier or forums or websites.
56
Appendix
Open source software notice
The following GPL executables and LGPL libraries used in this product are
subject to the GPL2.0/LGPL2.1 License Agreements:
GPL EXECUTABLES:
Linux kernel 2.6, bash, busybox, gdbm, libreadline, module-init-tools,
mount, mtd-utils, net-tools, quftp, tar, util-linux
LGPL LIBRARIES:
Glibc, libelf, libesmtp, live.media
LG Electronics offers to provide source code to you on CD-ROM for a
charge covering the cost of performing such distribution, such as the cost
of media, shipping and handling upon e-mail request to LG Electronics at:
opensource@lge.com
This offer is valid for a period of three (3) years from the date of the
distribution of this product by LG Electronics.
You can obtain a copy of the GPL, LGPL licenses from http://www.gnu.org/
licenses/old-licenses/gpl-2.0.html and http://www.gnu.org/licenses/oldlicenses/lgpl-2.1.html .
This product includes mDNSResponder component which is licensed
under the terms of the Apache License, Version 2.0.
You can obtain a copy of the Apache license from http://www.apache.
org/licenses/LICENSE-2.0.html .
This product includes
•
dhcp client :
Copyright © 2004-2008 by Internet Systems Consortium, Inc.
(“ISC”)
Copyright © 1995-2003 by Internet Software Consortium
•
expat library : Copyright © 2006 expat maintainers.
57
•
libcap
•
libjpeg : Independent JPEG Group Copyright © 1991-1998,
Thomas G. Lane.
•
libmd5 : Copyright © 2002 Aladdin Enterprises.
•
libncurses : Copyright © 1998,2002 Free Software Foundation, Inc.
•
libpcre : Copyright © 1997-2009 University of Cambridge
•
UPnP SDK : Copyright © 2000-2003 Intel Corporation
•
libxml2 : Copyright © 1998-2003 Daniel Veillard.
•
lighttpd : Copyright © 2004, Jan Kneschke, incremental
•
ntpdate : Copyright © David L. Mills 1992-2006
•
OpenSSL :
--
cryptographic software written by Eric Young (eay@cryptsoft.
com).
--
software written by Tim Hudson (tjh@cryptsoft.com).
--
software developed by the OpenSSL Project for use in the
OpenSSL Toolkit. (http://www.openssl.org)
•
PHP software, freely available from http://www.php.net/software/
: Copyright © 1999 - 2009 The PHP Group.
•
Speex :
--
Copyright 2002-2008 Xiph.org Foundation
--
Copyright 2002-2008 Jean-Marc Valin
--
Copyright 2005-2007
Analog Devices Inc.
--
Copyright 2005-2008
Commonwealth Scientific and
Industrial Research Organisation (CSIRO)
--
Copyright 1993, 2002, 2006 David Rowe
--
Copyright 2003 EpicGames
--
Copyright 1992-1994
Jutta Degener, Carsten Bormann
58
• Zlib : Copyright © 1995-2002 Jean-loup Gailly and Mark Adler.
All rights reserved.
Permission is hereby granted, free of charge, to any person obtaining a
copy of this software and associated documentation files (the “Software”),
to deal in the Software without restriction, including without limitation
the rights to use, copy, modify, merge, publish, distribute, sublicense,
and/or sell copies of the Software, and to permit persons to whom the
Software is furnished to do so, subject to the following conditions:
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
OTHER DEALINGS IN THE SOFTWARE.
59
Specification
Item
LVS201
Resolution (Max)
704 x 480 (NTSC), 704 x 576 (PAL)
Output
RJ-45 (Network)
Frame Rate(Max)
30 fps / 25 fps (NTSC/PAL)
Compression
H.264 (Basic Profile)/ MJPEG /Dual Stream
Event Detection
Motion detection
Event Notification
Encryption
SMTP, FTP
Multi level user ID/password
(Admin, Power, Normal, Customer)
HTTPS (SSL)
Physical Layer
10/100 base TX Ethernet
Protocol
TCP/IP(IPv4), HTTP, HTTPS, RTP, RTSP, UDP,
DHCP, FTP, SMTP, NTP, ARP, ICMP, DDNS(LG)
IP support
Dynamic, Static, Private IP
Users
Operation Temp. /
Humidity
Power Source
Unicast 10 Streams / 50 user registration
Power Consumption
About 3 W
Dimension (W x H x D)
100 mm x 41 mm x 91 mm
Weight
204 g
Other
RS-485 Support
ID/Password
-10 ºC to 50 ºC / 0 % RH to 80 % RH
PoE, DC 12 V (±20 %) (1 A or above)
BZ03
Download PDF

advertising