LG | LW345-FP | LG LW345-FP Owner’s Manual

OWNER'S MANUAL
High Definition Network Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
LW342 series
LW345 series
P/NO : MFL62591948
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 1
1010 (V1.0)
11. 2. 25. �� 11:01
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if
an unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
•
A suitable conduit entries, knock-outs or glands shall
be provided in the cable entries of this product in the
end user.
2
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 2
11. 2. 25. �� 11:01
•
•
Caution: Danger of explosion if battery is incorrectly
replaced. Replaced only with the same or equivalent
type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s
instructions.
Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall be
provided with brushings.
This Class A digital apparatus complies with Canadian
ICES-003.
Caution: This installation should be made by a qualified
service person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
To disconnect power from mains, pull out the mains
cord plug. When installing the product, ensure that the
plug is easily accessible.
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
Warning: Do not install this equipment in a confined space
such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the
National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Warning: To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
3
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 3
11. 2. 25. �� 11:01
Disposal of your old appliance
1.
When this crossed-out wheeled bin
symbol is attached to a product it means
the product is covered by the European
Directive 2002/96/EC.
2.
All electrical and electronic products
should be disposed of separately from
the municipal waste stream via designated collection facilities appointed by
the government or the local authorities.
3.
The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and
human health.
4.
For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you purchased the product.
LG Electronics hereby declares that this/
these product(s) is/are in compliance with
the essential requirements and other relevant
provisions of Directive 2004/108/EC,
2006/95/EC, and 2009/125/EC.
European representative :
LG Electronics Service Europe B.V. Veluwezoom
15, 1327 AE Almere. The Netherlands
(Tel : +31-(0)36-547-8888)
EEE Compliance with Directive. (for Turkey only)
4
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 4
11. 2. 25. �� 11:01
Important Safety Instructions
1.
Read these instructions.
and the point where they exit from the apparatus.
2.
Keep these instructions.
3.
Heed all warnings.
11. Only use attachments/accessories specified by the
manufacturer.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
5
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 5
11. 2. 25. �� 11:01
Cautions for Safe Operation
Handling of the unit
Operating and storage location
Be careful not to spill water or other liquids on the unit. Be
cautious not to get combustible or metallic material inside
the body. If used with foreign matter inside, the device is
liable to fail or to get cause of fire or electric shock.
Avoid viewing a very bright object (such as light fittings)
during an extended period. Avoid operating or storing the
unit in the following locations.
•
Remove dust or dirt on the surface of the lens with a
blower.
•
Use a dry soft cloth to clean the body. If it is very dirty,
use a cloth dampened with a small quantity of neutral
detergent then wipe dry.
•
Avoid the use of volatile solvents such as thinners,
alcohol, benzene and insecticides.
They may damage the surface finish and/or impair the
operation of the device.
•
Extremely hot or cold places (operating temperature
from -10 °C to 50 °C, however, we recommend that the
unit be used within a temperature range from
0 °C to 45 °C)
•
Damp or dust place
•
Places exposed to rain
•
Places subject to strong vibration
•
Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
6
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 6
11. 2. 25. �� 11:01
Contents
Features.................................................................. 8
Recommended PC Requirements............................21
Accessing the LG IP device.........................................21
Part Names and Functions.................................... 9
Connections......................................................... 12
LG Smart Web Viewer Overview...............................23
Configuring the LG IP camera...................................26
OSD Menu Setup...........................................................49
Precautions......................................................................12
Privacy Setting................................................................58
Connection Overview..................................................12
Back Focus Setting........................................................60
Connecting Display Device........................................13
Connecting Network....................................................13
Connecting Power Source..........................................14
Connecting Alarm Device...........................................15
Connecting Microphone and Speaker Device....16
Mounting the Lens........................................................17
Troubleshooting.................................................. 65
Open source software notice.............................. 68
Specification........................................................ 71
Focus adjustment .......................................................19
Camera Installation.......................................................19
Operation and settings....................................... 20
Before using the system..............................................20
7
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 7
11. 2. 25. �� 11:01
Features
The LG Network Camera is designed to use on an Ethernet
network and must be assigned an IP address to make it
accessible.
This manual contains instructions on how to install and
manage the LG Network Camera in your networking environment. Some knowledge of networking environments
would be beneficial to the reader.
Should you require any technical assistance, please contact
authorized service center.
•
Dual H.264 Stream for single Video Input
•
Multi-Codec (H.264, MJPEG) Streaming
•
Intelligent Video Analysis (Option)
•
PoE (Power over Ethernet) Support (802.3af )
•
2 Power (DC 12 V, PoE) Support
•
Audio Support (G.711, G.726 Full Duplex)
•
Pre/Post Alarm Support
•
High resolution and high sensitivity with a 6.49 mm
progressive scan CMOS.
•
Auto White Balance
•
Day & Night function
•
WDR (Wide Dynamic Range) is available
•
ABF Auto Back Focus function
Features Chart
This table shows the differences between the models.
LW345 is used for the description, operations and details
provided in this manual.
Models
LW342
LW345
VCA
No
Yes
8
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 8
11. 2. 25. �� 11:01
Part Names and Functions
a
b
c
a Lens mount cap
The lens mount of the camera is covered using a cap
to protect it. Remove the lens cap covering the lens.
b Camera installation hole
Use this hole to install the camera on the wall.
c Lens iris output connector (LENS)
This 4- pin connector is used to send the Iris control
signal and power supply to an auto-iris type lens.
9
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 9
11. 2. 25. �� 11:01
Part Names and Functions
d VIDEO OUT
Supplies analog video signal (composite) to the connected device.
e ETHERNET/POE Port
d
e
i
Connects to a PC or a network via a hub with a
10 BASE-T/100 BASE-TX cable attached RJ-45 connector.
Note:
j
f
g
h
k
l
Power over Ethernet (PoE) is a technology that integrates power into a standard LAN infrastructure. It
enables power to be provided to the network device,
such as a network camera, using the same cable as
that used for network connection. It eliminates the
need for power outlets at the device locations and
enables easier application of uninterruptible power
supplies (UPS).
f External device connectors
•
A IN(R)/A IN (Sensor input) Terminals:
Provides physical interface for sensor.
•
A OUT(R)/A OUT (Relay output) Terminals:
Provides physical interface for Alarm/Relay.
10
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 10
11. 2. 25. �� 11:01
Part Names and Functions
g ABF Auto Back Focus button
ABF Auto Back Focus is an adjustable function for the
back focus automatically. Before you use it, you should
set the zoom and focus of the lens approximately. If
you press this button, the camera will be activated to
adjust the back focus automatically. If you keep pressing this button about 4 seconds, the focus reset function will be activated.
l AUDIO OUT (Line Level Output)
Connect to an active speaker with a built-in amplifier.
h Power input terminal
Connects to a DC 12 V power supply using proper
cables.
i Power indicator
Lights when the camera is powered.
j RESET button
Push the button more than 3 seconds, this would
restore the factory default network related settings.
k AUDIO IN (Line Level Input)
Input for a mono microphone, or a line-in mono
signal.
11
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 11
11. 2. 25. �� 11:01
Connections
Precautions
•
Be sure to switch off the unit before installation and connection.
•
The installation should be made by qualified service personnel or system installers.
•
Do not expose the power and connection cables to moisture, which may cause damage to the unit.
Connection Overview
PoE Device
(IEEE802.3af )
12
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 12
11. 2. 25. �� 11:01
Connections
Connecting Display Device
Connect the IP camera to your network using a standard
RJ-45 network cable as shown below.
Connect the video signal between the IP camera and the
monitor.
PoE Device
(IEEE802.3af )
Broadband
Service
Router
Broadband
Service
Connecting Network
You can control and monitor the system via network. With
the remote control (monitoring), you can change the system configuration or monitor the image via network. After
the installation, check the network settings for the remote
control and monitoring work.
13
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 13
11. 2. 25. �� 11:01
Connections
Connecting Power Source
Connect power, using one of the methods listed below:
To use the power adapter
Connect to the DC 12 V UL Listed, Class 2 Power
Supply only on the unit. (Recommended power adapter is DC 12 V/1.5 A or above)
Connect a power source to the power input terminal
with 2 and 3 aligned correctly as shown below.
14
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 14
11. 2. 25. �� 11:01
Connections
To use the PoE (Power over Ethernet) device
Connect the PoE cable to the LAN port on the unit.
You must use the “IEEE802.3af” standard PoE device.
PoE Device
(IEEE802.3af )
Connecting Alarm Device
Alarm terminals are used to connect the alarm (relay)
devices such as sensors, door switches, etc.
A IN(R)/A IN (Sensor Input )
Connect the sensor device to the sensor input
terminal.
Note:
If the camera doesn't work properly after connecting PoE
device, please check if the PoE device supplies enough
power.
Sensor
Device
15
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 15
11. 2. 25. �� 11:01
Connections
A OUT(R) / A OUT (Relay Output)
Connect the alarm (relay) device to the relay output
terminal. Alarm signal is outputted at an event
occurrence.
Alarm (Relay)
Device
Connecting Microphone and
Speaker Device
Optionally connect an active speaker and/or external
microphone with a built-in amplifier.
Note:
The Photo MOS Relay is rated for 100 mA at 20 V DC or
100 mA at 28 V AC.
Note:
Keep the microphone away from the speaker to avoid
howling.
16
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 16
11. 2. 25. �� 11:01
Connections
Mounting the Lens
1. Remove the lens mount cap from the camera.
3.
Connect the lens plug to the lens iris output connector (LENS) on the side of the camera.
When using lenses from other makers, the plug shape
may not correspond to the terminal on the camera.
In such a case, remove the original plug and using a
soldering iron, connect a lens iris plug according to
the diagram. (Refer to next page.)
Note:
Recommended DC-Iris Lens
2. Install the CS mount type lens.
Carefully align the lens mount with the camera opening, then turn the lens slowly to install it.
Maker
model name
FUJINON
YV4.3X2.8SA-SA2L
We recommend using over 2 M pixel lens for optimum
resolution.
17
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 17
11. 2. 25. �� 11:01
Connections
lens iris output connector
Rewire the lens iris plug
Pin layout for the lens iris output connector.
1. Cut off the plug of the lens cable, cut off approximately 8 mm of the insulation, and then strip
approximately 2 mm of the ends of the cable
sheaths.
No.
DC type lenses
VIDEO type lenses
1
Damping -
Vcc (+9 V)
2
Damping +
Not used
3
Drive +
Video
4
Drive -
Ground
2. Solder the ends of the cable wires to the ends of
the pins, and then attach the cover of the lens iris
plug.
18
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 18
11. 2. 25. �� 11:01
Connections
Focus adjustment
Camera Installation
After installing the lens, you should adjust the focus as
shown below steps.
Select a location that is strong enough to bear the full
weight and install the camera securely.
1. Keep pressing the ABF button about 4 seconds to initialize the focus.
2. Set the zoom level of the lens approximately.
3.
Set the focus of the lens approximately.
4. Press the ABF button. The camera will be activated to
adjust the focus automatically.
19
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 19
11. 2. 25. �� 11:01
Operation and settings
Before using the system
•
To view streaming video in Internet Explorer, set your
browser to allow ActiveX controls. If you find this message “This website wants to install the following addon: ‘IPCam_Streamer.cab’ from ‘LG ELECTRONICS INC’”,
Click the yellow bar and install LG Smart Web Viewer
Program on your computer.
•
Before using the LG IP device make sure the connections are correct and verify whether proper power
supply is used.
•
Check the connections of the LG IP device for the correct conditions.
•
•
Check that the LG IP device is(are) connected to the
network and that power is supplied.
The Layouts and the Live view pages may differ with
different OS (Operating Systems) and Web Browsers.
•
•
Once the connections are made you need to install the
LG client program to the PC from which you want to
access the device. The LG Smart Web Viewer program
is automatically installed when you connect the LG IP
device.
The LG Smart Station and the LG Smart Web Viewer
program are the network program of the LG Video
Server and the LG IP cameras.
Care needs to be taken not to run any other applications when the Client Program is running as it may
cause memory shortage.
20
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 20
11. 2. 25. �� 11:01
Operation and settings
Recommended PC Requirements
Accessing the LG IP device
The LG IP device can be used with most standard operating
systems and browsers.
You can access the LG IP device by following the below
steps.
Items
Operating
System
CPU
Web Browser
Requirements
Intel Core2 Quard Q6700 (2.66 GHz) or
above
Microsoft Internet Explorer 6.0 or higher
DirectX 9.0 or above
Memory
2 GB or above RAM
Resolution
256 MB or above Video RAM
1 280 x 1 024 (with 32 bit color) or
higher
Copy the IP Utility to your PC
1.1 Insert the Client Program CD.
Windows XP Professional
DirectX
Graphics Card
1.
1.2 Find and Copy IP Utility folder to your PC.
2.
Discover LG IP device using the IP Utility
The IP Utility can automatically discover and display
LG IP devices on your network. The IP Utility shows the
MAC address, IP address, Model name and so on.
Note:
The computer running the IP Utility must be on the
same network segment (physical subnet) as the LG IP
device.
2.1 Run the IP Utility program.
2.2 Click the [Search] icon or select the [Search]
option in the Device search menu.
After a few seconds the found LG IP devices will
be displayed in the IP Utility window.
21
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 21
11. 2. 25. �� 11:01
Operation and settings
3.
Logging in to the LG Smart Web Viewer
The LG Smart Web Viewer can be used with most
web browsers. The recommended browser is Internet
Explorer with Windows.
3.1 Run the IP Utility and find the LG IP devices.
3.2 When the LG IP devices appear in the IP Utility
window, double-click IP address or right click on
the same IP address and select "Connect to Web
Page" to start the LG Smart Web Viewer. When
accessing the LG Smart Web Viewer, the authentication dialog appears on the screen.
3.3 Enter the user name and password. (Note that the
default administrator user name and password
are “admin”.)
•
•
If the login window is not displayed, check the
pop-up blocker. If you set the pop-up blocker, the
login window is not displayed. You must allow
the pop-ups.
•
If you connect the LG Smart Web Viewer for
the first time, the Security Warning window is
displayed to install the LG Smart Web Viewer program. You must install the LG Smart Web Viewer
program for using the LG IP device.
•
If your computer or network is protected by a
proxy or firewall, the proxy or firewall settings
can prevent the LG Smart Web Viewer program.
Change the proxy or firewall settings to activate
the LG Smart Web Viewer program.
3.4 Click the [OK] button and then the LG Smart Web
Viewer is displayed in your browser.
Notes:
•
You can also access the LG Smart Web Viewer as
shown below.
3.1 Start your Web browser.
3.2 Enter the IP address of the LG IP device in
the address bar of the browse.
3.3 Enter the user name and password set by the
administrator.
3.4 Click the [OK] button and then the LG Smart
Web Viewer is displayed in your browser.
The LG Smart Web Viewer needs more time to display it according to the network conditions.
22
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 22
11. 2. 25. �� 11:01
Operation and settings
LG Smart Web Viewer Overview
23
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 23
11. 2. 25. �� 11:01
Operation and settings
Item
Description
Select the video image size from the drop-down list. (1 080p, 720p, D1 or CIF)
The initial view size is set to D1.
Displays the current video codec of the selected video stream (Master or Slave).
Check this option as the network connection type (TCP or UDP). If you check it, the client
connects to the server using TCP connection.
Click to save the current image in JPEG format on your computer.
1.
Click the [Snapshot] button and then the Snapshot window is displayed.
2.
Click the [Save] button in the Snapshot window.
3.
Enter the file name (JPEG format) and select the folder to save it.
4.
Click the [Save] button to confirm it.
5.
Click the [Close] button in the Snapshot window to close it.
Displays the Camera OSD control window. Use these buttons to setup the Camera. This
button does not appear on the screen if the login is other than the administrator.
24
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 24
11. 2. 25. �� 11:01
Operation and settings
Select the video stream. From the Live view drop-down list, select the desired video
image source between [Master-0] and [Slave-0].
Note:
Master and Slave are output video streams. You can set the stream configurations independently for either Master or Slave stream. This would facilitate the user to set the live
view at his comfort.
Provides all the necessary tools for setting up the device to your requirements. The user
will need administrator level to do this.
Note:
If you want to exit the Configuration menu, select one of the video stream in the Live
view drop-down list.
Displays the current surveillance live screen.
You can monitor the camera image on the live view window of the LG Smart Web Viewer.
Click this button to connect or disconnect the audio communication between the LG IP
device and the connected PC.
(Color icon: On, Gray scale icon: Off.)
25
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 25
11. 2. 25. �� 11:01
Operation and settings
Click this button to switch the microphone off and on for the computer.
(Color icon: On, Gray scale icon: Off.)
Click this button to switch the sound off and on, for the speaker of the computer.
(Color icon: On, Gray scale icon: Off.)
Configuring the LG IP camera
The features and options of the LG IP camera are configured through the Configuration menu.
Only administrator-level users have permission to access the Configuration menu.
Accessing the Configuration menu
Click the [Configuration] button to display the LG Smart Web Viewer configuration window.
Warning
The Configuration setup should be made by qualified service personnel or system installers.
26
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 26
11. 2. 25. �� 11:01
Operation and settings
Configuration menu overview
The following table shows the list of menu items.
Main Menu
Sub Menu
Event schedule
Event
Event server
Sensor & Relay
Version
Date & Time
System
Maintenance
Log & Report
Language
Camera
Audio & Video
Stream
Audio
Motion detect
Basic
RTP stream
Network
TCP/IP
DDNS
IP filtering
User
Basic
27
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 27
11. 2. 25. �� 11:01
Operation and settings
System settings
Date & Time
Version
Displays the current version of Firmware, Hardware,
Software and Web Client.
Time zone
Set the time difference from GMT in the area where
the IP device is installed.
Select the time zone in the area where the IP device is
installed from the drop down list.
28
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 28
11. 2. 25. �� 11:01
Operation and settings
Time mode
>> Synchronize with NTP Server: Select if you
want to synchronize the IP device’s date and
time with those of the time server called NTP
(Network Time Protocol). Specify the NTP
server’s name. Click the [Test] button for connection test to the server.
>> Synchronize with personal computer: Select
if you want to synchronize the IP device’s
date and time with your computer.
>> Synchronize manually: Select if you want to
set the IP device’s date and time manually.
Select the year, month and date by clicking
the calendar button. Set hour, minutes and
seconds in the edit boxes.
Server time
>> Server time: Displays the current date and
time of the IP device.
•
Save: Click this button to confirm the settings.
Maintenance
System reboot
Click the [Reboot] button to restart the IP device. It
takes some minutes for the IP device to start again.
29
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 29
11. 2. 25. �� 11:01
Operation and settings
Backup and Restore
>> Backup: To take a backup all of the settings.
If necessary, it make possible to return to a
backuped configuration. Click this button
and follow the instructions on the browser
to specify the folder and save the setting
data of the IP device. This configuration
backup can be restored whenever needed.
>> Restore:
1. Click the [Browse] button.
2. Find and open the file in which the configuration setting data is stored.
3. Click the [Restore] button and the system settings will be restored and reboot
the system.
Notes:
•
Backup and Restore can happen on IP device
having the same version of firmware. This
feature is not intended for multi-configurations or for firmware upgrades.
•
The [Backup] function is allowed in HTTP
protocol but not in HTTPS protocol.
Firmware
>> Upgrade
1. Click the [Browse] button.
2. Find and open the firmware file.
3. Click the [Upgrade] button to update
the firmware.
Note:
When you upgrade the system, it may take
some minutes to be done. Do not close the
browser while the upgrade is in progress. If
you close the browser, it may cause a malfunction. You should wait until the confirmation window is displayed. When the upgrade
is finished, the confirmation window will be
displayed.
>>
Initialize: The [Initialize] button should be
used with caution. Clicking it will return all of
the IP device’s settings to the factory default
values. (Except for Network settings, PTZ
Protocol and Preset settings.)
30
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 30
11. 2. 25. �� 11:01
Operation and settings
Log & Report
Language
Log & Report status
The System log provides a summary of the status of
the IP device. The unit records the data of the software
activity in a file.
>>
>>
View Log: Click this button to display the
system log information.
View report: Click this button to display the
report of the system.
Language list
Select a language for the LG Smart Web Viewer configuration menu and information display.
•
Save: Click this button to confirm the settings.
31
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 31
11. 2. 25. �� 11:01
Operation and settings
Audio & Video settings
Camera
General
>> Contrast: Edit the contrast value from 0 to
100. Selecting 100 provides the image with
the highest contrast.
>> Standard: Displays the video standard of the
camera.
•
Save: Click this button to confirm the settings.
•
Default: Click this button to restore the IP device
back to original factory settings.
Preview
You can preview the camera image on the preview
window.
32
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 32
11. 2. 25. �� 11:01
Operation and settings
Stream
>>
>>
>>
Master/Slave
>> Enable: Click to activate the stream function.
>> Video codec: Select the video mode (Codec)
from the drop-down list. The viewer can
choose between MJPEG and H.264.
>> Resolution: Select the image size to be sent
from the camera.
(1 080p (1 920 x 1 072), 720p (1 280 x 720),
D1 (704 x 480) and CIF (352 x 240)).
>>
>>
Maximum Frame rate: Set the frame rate of
the image.
GOP size: It means “Group of Pictures”. The
higher the GOP, the better is the video quality of the camera. Edit the value of GOP from
1 to 30. This setting is valid for H.264 video
format only.
Quality: Select the Quality.
-VBR: The bit rate may vary depending
on the complexity of the video to meet
the selected quality.
-CBR: The video quality may vary in order
to preserve a constant bit rate.
Stream quality: If the [Quality] option set
to VBR, this option is displayed. Select the
stream quality from the drop down box, the
camera supports five types (Highest, High,
Medium, Low and Lowest)
Bit rate: If the [Quality] option set to CBR, this
option is displayed. Edit the bit rate value
from 256 kbps to 10 240 kbps.
33
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 33
11. 2. 25. �� 11:01
Operation and settings
Note:
If the ‘Bit rate’ is configured too low with
high resolution, the actual frame rate will
decrease because of narrow bandwidth. So
you need to set or change the ‘Bit rate’ to
high value.
•
Save: Click this button to confirm the settings.
>>
Audio type: Select the codec when you send
the audio from the microphone input connector.
Audio Out
>> Enable: Click the check box to output the
audio from the speaker.
•
Save: Click this button to confirm the settings.
Audio
Audio In
>> Enable: Click the check box if you want to
send the audio from the microphone input
connector.
Note:
The Clients connected to the IP device
remain unaffected with additional changes
made in the setting.
34
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 34
11. 2. 25. �� 11:01
Operation and settings
Motion detect
General
>> Sensitivity: Enter the sensitivity to detect an
object in motion.
>> Save: Click this button to confirm the settings.
How to set the motion detect window
1. Click the [Add] button. The motion detect window is displayed. You can add the five windows
maximum for motion detection area.
2. Set the [Sensitivity] option.
3.
Click the edge or coner of the window box to
adjust the window size for motion detection.
4. Click the [Save] button to save the settings.
Notes:
Preview
You can preview the motion detection window on the
preview window.
•
You can reset the window size. Click one of the
window edge or coner and drag & drop to reset
the motion detection area.
•
Motion Detection can be activated when at least
one of channels(Master/Slave) is enabled, Video
codec is set to H.264 and GOP size is more than 2.
35
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 35
11. 2. 25. �� 11:01
Operation and settings
Network settings
>>
Basic
>>
RTSP port: Check RTSP port. The default port
is 554. Other ports can be selected within
the range 1 025 to 65 535.
Network encryption: Select the HTTP or
HTTPS option for security.
Note:
The RTSP port number should not be same
with the web port number.
ARP Ping
>> Enable ARP Ping to configure IP address:
Check to enable ARP ping.
•
Save: Click this button to confirm the settings.
General
>> MAC address: Displays the MAC address.
Port & Encryption
>> Web port: The default HTTP port number
(80) can be changed to any port within the
range 1 025 to 65 535.
36
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 36
11. 2. 25. �� 11:01
Operation and settings
RTP stream
RTP (Real-time Transport Protocol) is an internet protocol
that allows programs to manage the real-time transmission
of multimedia data, via unicast or multicast.
Master / Slave
>> RTP unicast: When enabled the transmission of the data to the specified equipment
happens on a network specifying a single
address.
>> RTP multicast: When enabled it reduces the
transmission load on the camera by making
the computer of the same segment network
receive the same transmission data. When
multicast option is checked then select
Video Port number, Audio Port number and
Data port number.
-Video RTP port: Specify the video
transmission port number used for the
multicast streaming. It is initially set
to 8 888 and you can edit this between
1 025 and 65 534.
-Audio RTP port: Specify the audio
port number used for the multicast
streaming. It is initially set to 7 778 and
you can edit this between 1 025 and
65 534.
37
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 37
11. 2. 25. �� 11:01
Operation and settings
--
Data RTP port: Specify the VA data port
number used for the multicast streaming. It is initially set to 6 666 and you
can edit this between 1 025 and 65 534.
-IP address: Set the IP address for RTP
multicast.
Note:
Each stream using multicast needs its own
a pair of multicast IP address and port numbers to avoid address conflict.
TCP/IP
TTL
>>
•
TTL: This option indicates the Time-To-Live
of multicast packets. The default setting is 7,
and the allowed TTL range is from 1 to 255.
Save: Click this button to confirm the settings.
IP address status
>> Automatically set with DHCP: Select this
option when a DHCP server is installed on
the network to allow IP address assignment.
With this setting, the IP address is assigned
automatically.
-Notify to SMTP server, if IP address is
changed: If you select this option, the
user get a notification mail telling about
changing of IP of the IP device.
38
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 38
11. 2. 25. �� 11:01
Operation and settings
Note:
You should register the SMTP server
on the Event server setting to set this
function.
>> Statically set: Select this option when you set
a fixed IP address, with this setting, specify
the IP address, Subnet mask and default
gateway manually.
-IP address: Enter an IP address.
-Subnet mask: Enter a subnet mask
address.
-Gateway: Enter the gateway address.
DNS server status
>> Primary DNS server: Enter the Primary
domain name server that translates the hostnames into IP address.
>> Secondary DNS server: Enter the Secondary
DNS server address that backups the Primary
DNS.
•
Save: Click this button to confirm the settings.
DDNS
This free service is very useful when combined with the LG
DDNS Server. It allows the user to connect the IP device
using the URL, rather than an IP Address. This also solves
the problem of having a dynamic IP address.
DDNS status
>> Don’t use DDNS server: Disable the DDNS
function.
>> Use DDNS server: Enable the DDNS function.
-Provider: Displays the DDNS provider.
-Hostname: Enter the hostname you
want to use.
•
Save: Click this button to confirm the settings.
39
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 39
11. 2. 25. �� 11:01
Operation and settings
IP filtering
The access of the IP addresses in the list are allowed or
denied according to the choice made in the drop-down list
of the Basic policy option. The administrator can add up to
10 IP address entries to the list (a single entry can contain
multiple IP addresses). The users from these IP addresses
need to be specified in the user list with the appropriate
access rights. The IP list is to control the access permission
of clients by checking the client IP address.
IP list
>>
•
Basic policy: Select the basic policy type.
-Allow all: Allow all the IP address basically, but the IP addresses in the list are
denied.
-Deny all: Deny all the IP address basically, but the IP addresses in the list are
allowed. It needs at least one IP address
to activate this function.
Save: Click this button to confirm the settings.
•
Add: Click this button to add the IP address.
1. Click the [Add] button.
2. Set the IP options.
-Alias: Enter the alias.
-From: Enter the start IP address for the
IP filtering.
-To: Enter the end IP address for the IP
filtering.
40
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 40
11. 2. 25. �� 11:01
Operation and settings
Note:
If you want to deny or to allow a range of
IP addresses, enter the start IP address to
"From" and the end IP address to "To". You
can also add an IP address by entering the
same IP address to "From" and "To".
•
3. Click the [Save] button.
4. Repeat the steps 1 to 3 to add additional IP
address.
Remove: Click this button to delete the IP
address.
1.
2.
User settings
Basic
The IP device is shipped with the login rights of administrator only. If others need to access the IP device excluding
the configuration a login with viewer rights need to be created. A maximum of 50 users can be created.
Select the alias from the list.
Click the [Remove] button. The IP address
will be deleted.
41
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 41
11. 2. 25. �� 11:01
Operation and settings
User list
>> Add the User
You can register a new user with various
access rights.
Click the [Add] button. User setting dialog is displayed.
2. Enter the new User ID and Password.
(Should have a minimum of 4 characters and preferably a combination of
alphanumeric).
3. To confirm the password, retype
the password that you typed in the
Password box.
4. Select the authority from the drop
down list to provide the access rights to
each user and then click the [Save] to
confirm your selection.
-Administrator: Allows you to operate setup menus and to view live
images.
--
1.
--
--
Power user: Use of the limited functions of the system (The
Configuration menu is not allowed.
A power user can use the Live
View, OSD control and audio functions.
Normal user: Provides the lowest
level of access. Allows to view live
images only.
Custom user: The user can login
and view the live stream image
only when the “Enable anonymous login” option is checked to
enable it.
Note:
Remember the password.
42
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 42
11. 2. 25. �� 11:01
Operation and settings
>>
>>
Edit the registered user
You can change the password or authority.
1. Choose the user ID and then click the
[Edit] button.
2. Change the Password or Authority, then
click the [Save] button to confirm your
selection.
Delete the registered user
1. Choose the user ID you want to delete.
2. Click the [Remove] button.
Note:
The default administrator user ID ‘admin’ and
‘anonymous’ are permanent and cannot be
deleted.
Anonymous
>> Enable anonymous login
Check the box to enable anonymous user
login - allows the user access for only viewing the live stream image.
Max RTP stream connection
>> Maximum number of simultaneous stream
connection:
Set this number to limit the number of
simultaneous stream connections.
The connections depend on the stream
configuration as shown in the following
Maximum RTP stream connection by stream
configuration.
Video
Codec
Resolution
Frame
Rate
Quality
Maximum
RTP stream
H.264
1080p
30
HIGHEST
Up to 5
H.264
1080p
30
MEDIUM
Up to 10
H.264
720p
30
HIGHEST
Up to 10
MJPEG
1080p
10
HIGHEST
Up to 3
MJPEG
720p
20
HIGHEST
Up to 7
43
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 43
11. 2. 25. �� 11:01
Operation and settings
Note:
Preview window of the IP device setting and
preset setting are affected by this setting.
•
Save: Click this button to confirm the settings.
Event settings
Event schedule
When an event (VA/Modtion detect/Sensor event) occurs,
this unit records the live images and routes as configured.
Event schedule list
>> To edit the Event Schedule
1. Select the Trigger event and click the
[Edit] button. Event schedule window is
displayed.
2. Set the options.
44
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 44
11. 2. 25. �� 11:01
Operation and settings
•
Trigger: Displays the selected trigger event.
•
Time: Sets the Day, Start, Finish, Pre
alarm, Post alarm and Ignore interval time options.
•
Action: Selects the options. This
occurs when the event runs.
--
•
3.
FTP server/SMTP server:
Uploading of images to an
FTP server, or e-mail notification.
-Control relay: The relay is activated or deactivated.
Stream: Selects the stream of the
connected camera.
Note:
You should register the SMTP and FTP server
on the Event server setting to set this function.
Event Server
Event Servers are used to receive the recorded video clip
and/or notification messages.
Click the [Save] button to confirm the
settings.
45
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 45
11. 2. 25. �� 11:01
Operation and settings
FTP server list
Image files can be transferred to the FTP server within
the scheduled time. Image file that has been recorded
linked to an external event is sent to the FTP server
periodically.
>>
To add the FTP server
1. Click the [Add] button. FTP server setting window is displayed.
2. Set the FTP server options.
-Alias: Type the FTP Server name to
upload the image files.
-Address: Enter the FTP server’s IP
address.
-Port: Enter the port number. The
default FTP port is 21.
-User ID: Type the user name for the
Folder shared in the FTP server.
-Password: Type the password for
the folder shared in the FTP Server.
-Folder: Type the path with the folder that is shared in the FTP server.
--
>>
>>
Test: Select [Test] to test the FTP
server.
3. Click the [Save] button to confirm the
settings.
To edit the FTP server
1. Choose the FTP server in the FTP server
list.
2. Click the [Edit] button.
You can check or edit the FTP server
options.
To delete the FTP server
1. Choose the FTP server in the FTP server
list.
2. Click the [Remove] button. This would
remove the FTP server from the list.
46
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 46
11. 2. 25. �� 11:01
Operation and settings
SMTP server list
By selecting the e-mail option, a still image of the
event is captured and an e-mail with the attached
image file is sent to the specified mail address.
>>
To add the SMTP server
1. Click the [Add] button. SMTP server setting window is displayed.
2. Set the SMTP server options.
-Alias: Enter the SMTP server name.
-User ID: Enter the user ID of the
SMTP server. This would be the one
who owns the mail account.
-Password: Enter the password of
the SMTP server.
-Address: Enter the SMTP server
address.
-Port: Enter the port number. The
default port is 25.
--
Enable SSL: Check when use the
SSL (Secure Socket Layer) protocol. SSL protocol is cryptographic
protocols that provide secure communication on a network.
-Receiving address: Type the
recipients e-mail address. You can
specify only one recipient e-mail
address.
-Administrator address: Type the
e-mail address of the administrator.
-Subject: Enter the subject/title of
the e-mail.
-Message: This message can
describe the information of the
acquired IP address, etc.
-Test: Select [Test] to test the SMTP
server.
3. Click the [Save] button to confirm the
settings.
47
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 47
11. 2. 25. �� 11:01
Operation and settings
>>
>>
To edit the SMTP server
1. Choose the SMTP server in the SMTP
server list.
2. Click the [Edit] button.
You can check or edit the SMTP server
options.
To delete the SMTP server
1. Choose the SMTP server in the SMTP
server list.
2. Click the [Remove] button.
Sensor
>>
>>
>>
Relay
>>
>>
>>
>>
Sensor & Relay
•
Enable: Marks up when you want to activate
the sensor.
Alias: Displays the sensor name.
Type: Select the sensor type.
Control duration: Enter the relay time.
Alias: Displays the relay name.
Type: Select the relay type.
Control relay:
-Run: Click to activate the relay.
-Stop: Click to stop the relay.
Save: Click this button to confirm the settings.
48
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 48
11. 2. 25. �� 11:01
Operation and settings
OSD Menu Setup
Main Menu
The following table shows the list of menu items and options. You can adapt the camera to your requirements by
setting up the respective items in these menus.
Main Menu
EXPOSURE
Sub Menu
ELC/ALC
WDR/BLC
OFF/WDR/BLC/
HSBLC
BRIGHTNESS
0 to 100
AGC
OFF/LOW/MIDDLE/
HIGH
AUTO
-
AWC / PUSH
X64, ..., x2, AUTO,
OFF, A.FLK, 1/160,
..., 1/10 000
INDOOR,
OUTDOOR
-100 to 100
RED
BLUE
-100 to 100
EXIT
RET/TOP/END
LOW/ MIDDLE/
HIGH
LEVEL
AUTO
DAY/NIGHT
SENS-UP
AUTO
3D-DNR
RET/TOP/END
COLOR TEMP
MANUAL
OFF
EXIT
Contents
-
WHITE BAL
Contents
SHUTTER
Sub Menu
ATW
DWELL TIME
5, 10, 15s
EXIT
RET/TOP/END
DAY
-
NIGHT
-
OFF
-
LOW
-
MIDDLE
-
HIGH
-
49
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 49
11. 2. 25. �� 11:01
Operation and settings
Main Menu Sub Menu
OFF
COLOR
TRANSPARENCY
Contents
RED, GREEN,
BLUE
0 to 16
Main Menu
0 to 255
AREA1 to
AREA8
RECT. DISPLAY
ON/OFF
HEIGHT
4 to 100
WIDTH
4 to 100
MOVE Y
2 to 98
MOVE X
2 to 98
AREA1 to
MASK NUMBER
AREA2
CIR. DISPLAY
ON/OFF
HEIGHT
1 to 15
WIDTH
1 to 15
MOVE Y
0 to 100
MOVE X
0 to 100
RADIUS SIZE
0 to 100
AREA1 to
MASK NUMBER
AREA2
POLY. DISPLAY
ON/OFF
POLYGON DRAW
POLYGON MOVE
RET/TOP/END
BACK FOCUS
MASK NUMBER
RECTANGLE
PRIVACY
ON
CIRCLE
POLYGON
EXIT
Sub Menu
MANUAL ADJUST
ABF PUSH
FOCUS RESET
D/N ABF
EXIT
D-ZOOM
D-EFFECT
SHARPNESS
COLOR
SPECIAL
PIP
STABILIZER
USER TITLE
LANGUAGE
EXIT
Contents
RET/TOP/END
OFF
ZOOM
PAN
ON
TILT
EXIT
OFF/ MIRROR/ ROTATE/ V-FLIP
0 to 68
OFF/ ON
OFF
WINDOW MOVE
IMAGE MOVE
ON
IMG SIZE
EXIT
OFF/ ON
OFF/ ON
English
(The option depends on the model.)
RET/TOP/END
50
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 50
11. 2. 25. �� 11:01
Operation and settings
Main Menu
RESET
EXIT
Sub Menu
Contents
CAMERA REBOOT
-
FACTORY RESET
-
EXIT
-
-
-
51
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 51
11. 2. 25. �� 11:01
Operation and settings
General Operation
1.
2.
6.
Click the [OSD control] button on the LG Smart Web
Viewer.
Click
button on the OSD control window.
The camera setting menu appears on the live view
window.
Select [EXIT] option then click
button to exit the
setup menu. In the submenu, use
or
button to
select the [EXIT] then use
or
button to select a
mode and click
button to exit the setup menu.
•
RET: Return to the previous.
•
TOP: Return to the CAMERA SETTING menu
screen.
•
END: Exit the setup menu.
Notes:
3.
Use
or
button to select an option then click
button. Submenu appears.
4.
Use
or
button to select a submenu option.
5.
Use
or
button to select a value.
•
button: Used to move upper direction on the
menu screen.
•
button: Used to move lower direction on the menu
screen.
•
button: Used to increase the value selected in the
menu.
•
button: Used to decrease the value selected in the
menu.
•
button: Executes selections and displays a submenu for an item with the mark.
52
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 52
11. 2. 25. �� 11:01
Operation and settings
Exposure settings
1.
Select [WDR/BLC] option on the [EXPOSURE] menu.
2.
Use
or
button.
•
You can set the exposure options using the EXPOSURE
menu.
Select [EXPOSURE] option on the [CAMERA SETTING]
menu.
2. Use
or
button to select a mode (ALC
ELC).
3. Press
button and the EXPOSURE menu appears.
Notes:
ELC Mode is right for outdoor scenes.
•
ALC Mode is right for indoor scenes.
WDR/BLC
Use WDR/BLC option to view the object clearly in backlight
conditions.
WDR: WDR (Wide dynamic range) feature can be
very helpful to cope with very challenging lighting conditions. It is capable of capturing both of
the dark part and bright part and combining the
differences into a scene to generate a highly realistic image as original scene. Set the WDR limit.
>>
>>
1.
•
button to select a mode then click
•
•
WDR LIMIT: LOW
MIDDLE
HIGH
ACE (Adaptive Contrast Enhancement) : This
function is used when you want to display
dark areas of WDR brightly.
BLC: Camera's backlight compensation feature
helps alleviate issues of visibility in high contrast
areas. Set the BLC limit.
>> BLC LIMIT: LOW
MIDDLE
HIGH
HSBLC: Use for masking brightness of the specific
area to view the subject more clearly. The HSBLC
mode is automatically activated only in low luminance scene.
53
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 53
11. 2. 25. �� 11:01
Operation and settings
>>
•
AREA SETTING: Use
or
button to
select an area then use
or
button to
select [ON] or [OFF]. Click
button to exit
the area setting menu.
>> GRAY SCALE: Use
or
button to select a
gray scale.
(GRAY
D.GRAY
BLACK).
>> USER SCALE: Use
or
button to select a
bright level. (5 levels)
>> MASK: Use
or
button to select [ON] or
[OFF]. If you set the MASK to ON, the mask
function is activated only when the HSBLC is
activated by auto mode.
OFF: Not in use.
BRIGHTNESS
You can increase the brightness of the darkened video. If
you set the brightness to lower value, the image gets darkened. If you set the brightness to higher value, the image
gets bright.
1.
Select [BRIGHTNESS] option on the [EXPOSURE] menu.
2.
Use
or
AGC (Automatic Gain Control)
If the images are too dark, change the maximum [AGC]
value to make the images brighter.
1.
Select the [AGC] option on the [EXPOSURE] menu.
2.
Use
or
button to select a mode.
SHUTTER (Shutter Speed)
Select the desired shutter speed for camera exposure. You
can change the shutter speed to higher speed to capture
fast-moving subjects, though the image becomes darker.
1.
Select [SHUTTER] option on the [EXPOSURE] menu.
2.
Use
or
button to set shutter speed.
SENS-UP
If pictures are not clear due to darkness, this SENS-UP
operation would increase the sensitivity of picture.
1.
Select [SENS-UP] option on the [EXPOSURE] menu.
2.
Use
or
button to select a mode.
button to set the bright level.
54
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 54
11. 2. 25. �� 11:01
Operation and settings
•
AUTO: Adjust the sensitivity of the picture automatically.
>>
•
SENS-UP LIMIT: Use
or
button to set
the SENS-UP limit. (x2 to x64)
>> EXIT: Select a mode and click
button to
exit the menu.
OFF: Not in use.
White Balance settings
Select the method by which the camera shifts its output
colors to compensate for the color of a light source.
Note:
If you set to one of the SHUTTER options except AUTO on
the [SHUTTER] menu or [AGC] to [OFF], the [SENS-UP] setting is not available and [---] mark is displayed.
1.
Select the [WHITE BALANCE] option.
2.
Use
or
button.
•
button to select a mode then click
ATW (Auto-Tracing White Balance): In this mode,
white balance has better coverage than auto.
Proper white balance may not be obtained under
the following conditions:
>>
When the scene contains mostly high color
temperature objects, such as a blue sky or
sunset.
55
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 55
11. 2. 25. �� 11:01
Operation and settings
•
>> When the scene is dim.
AUTO: You can set the white balance options
automatically.
•
AWC / PUSH: If you select the AWC / PUSH
mode, you will be able to set up the White
Balance automatically using
button.
•
MANUAL: You can set the white balance options
manually.
>>
>>
>>
COLOR TEMP: Use
or
button to select
a function.
-INDOOR: The color temperature range
for the proper white balance is approximately 3 200 K.
-OUTDOOR: The color temperature range
for the proper white balance is approximately 5 100 K.
RED: Set the desired red value.
BLUE: Set the desired blue value.
Day/Night settings
1.
Select [DAY/NIGHT] option.
2.
Use
or
function.
•
button to select a mode for DAY/NIGHT
AUTO: DYA/NIGHT mode changes automatically.
Note:
If you set the AGC to [OFF] on the [EXPOSURE]
menu, the AUTO mode of the DAY/NIGHT function is not available and [---] mark is displayed.
56
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 56
11. 2. 25. �� 11:01
Operation and settings
>>
>>
•
LEVEL: Use
or
button to select a level.
DWELL TIME: Use
or
button to select
a dwell time.
DAY: Color mode enabled.
•
NIGHT: Black-and-white mode enabled.
3D-DNR setting
1.
Select [3D-DNR] option.
If pictures are not clear due to noise, this option would
reduce the noise of picture.
2.
Use
or
button to select an option.
Notes:
•
If you set the AGC to [OFF] on the [EXPOSURE] menu,
the [3D-DNR] function is not available and [---] mark
is displayed.
•
When you use this function, the afterimage may occur.
57
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 57
11. 2. 25. �� 11:01
Operation and settings
Privacy Setting
•
This function is aiming at the protection of personal privacy. The selected part is not displayed on the screen.
RECTANGLE :
>>
Use
or
button to select a mask on the
[MASK NUMBER].
>>
Use
or
button to set up the [ON] or
[OFF] on the RECT. DISPLAY option.
>>
1.
Select the [PRIVACY] option.
2.
Use
or
button to select [ON] and press
PRIVACY SETUP menu appears.
. The
•
COLOR: You can make any color by adjusting
R.G.B LEVEL.
•
TRANSPARENCY: You can adjust the transparency
of MASK.
•
Use
or
to select an option then use
or
button to adjust the option.
-- HEIGHT: Increase or decrease the vertical size of the mask.
-- WIDTH: Increase or decrease the horizontal size of the mask.
-- MOVE Y: Moves vertical position of the
mask.
-- MOVE X: Moves horizontal position of
the mask.
CIRCLE :
>>
Use
or
button to select a mask on the
[MASK NUMBER].
>>
Use
or
button to set up the [ON] or
[OFF] on the CIR. DISPLAY option.
58
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 58
11. 2. 25. �� 11:01
Operation and settings
>>
Use
or
to select an option then use
or
button to adjust the option.
-- HEIGHT: Increase or decrease the vertical size of the mask.
-- WIDTH: Increase or decrease the horizontal size of the mask.
-- MOVE Y: Moves vertical position of the
mask.
-- MOVE X: Moves horizontal position of
the mask.
-- RADIUS SIZE : You can adjust the
RADIUS SIZE.
•
POLYGON :
>>
Use
or
button to select a mask on the
[MASK NUMBER].
>>
Use
or
button to set up the [ON] or
[OFF] on the POLY. DISPLAY option.
>>
Use the , , ,
and
buttons to
draw the polygon by moving each vertex on
the [POLYGON DRAW]. Each movable vertex
will be displayed as a black square spot each
time you click the
button.
>>
Use the , , ,
and
buttons to
move the polygon on the [POLYGON MOVE].
59
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 59
11. 2. 25. �� 11:01
Operation and settings
Back Focus Setting
The back focus function is activated automatically according to your setting. And also, when the Day&Night function
is activated, the back focus function is activated automatically.
ABF ADJUST
You can adjust the back focus automatically.
1. Select the [ABF ADJUST] option on the [BACK FOCUS]
menu and then click
button. This function will be
activated automatically to adjust the back focus.
2. When the focus setting is finished, click
return to the previous menu.
button to
FOCUS RESET
Reset the focus point to factory default position.
MANUAL ADJUST
You can adjust the back focus manually.
1. Select the [MANUAL ADJUST] option on the [BACK
FOCUS] menu and then click
button.
2. Use
click
or
button to adjust the focus point then
button to exit the menu.
Select the [FOCUS RESET] option on the [BACK FOCUS]
menu and then click
button. The screen will be dim.
Use the [Manual Adjust] or [ABF push] option to adjust the
focus.
Note:
You can reset the focus using the ABF button. When you
keep pressing ABF button about 4 seconds, the camera will
reset the focus.
60
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 60
11. 2. 25. �� 11:01
Operation and settings
D/N ABF
You can set the Day&Night function with ABF function.
Use
or
Special menu settings
button to select a option.
•
ON: If you set to On, the ABF function will be activated
automatically when the D/N function is activated.
•
OFF: Not used.
D-ZOOM
You can select the digital zoom level.
1. Select [D-ZOOM] option on the [SPECIAL] menu.
2. Use
or
button to select [ON] then click
button. When you set to ON, the displayed image can be
shaking.
3. Use
or
or
button to select an option then use
button to select a level.
•
ZOOM: Use
screen.
•
PAN: Use
or
(left or right)
or
button to enlarge the
button to move the screen.
61
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 61
11. 2. 25. �� 11:01
Operation and settings
•
TILT: Use
or down)
or
button to move the screen. (up
SHARPNESS
The degree to which the boundary of the two portions is
clearly distinguished.
D-EFFECT (Digital effect)
You can select the digital effect.
1.
Select the [SHARPNESS] option on the [SPECIAL]
menu.
1.
Select the [D-EFFECT] option on the [SPECIAL] menu.
2.
2.
Use
Use
or
button to adjust the option. If you
set the sharpness value to higher, the image outline
becomes sharp. If you set to lower value, the image
outline becomes dim.
or
button to select a digital effect.
•
V-FLIP: Flip the picture vertically.
•
MIRROR: Turn on the mirror effect.
•
ROTATE: Rotate the picture. (180°)
•
OFF: Turn off the digital effect.
COLOR
You can switch the displayed picture to gray scale or color.
1. Select the [COLOR] option on the [SPECIAL] menu.
2.
Use
or
button to change a color effect.
•
ON: To display the picture with color.
•
OFF: To display the picture with grayscale.
62
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 62
11. 2. 25. �� 11:01
Operation and settings
PIP
You can view an image in PIP(picture in picture) mode.
1. Select the [PIP] option on the [SPECIAL] menu.
STABILIZER
The image stabilizer function minimizes the appearance of
shaky images caused by low-frequency vibration.
2.
Use
or
button to select [ON] then click
button. The PIP window is displayed on the live window.
This function is useful for outdoor surveillance.
•
Note:
WINDOW MOVE : The PIP window can be moved
through the live image window using , ,
and
buttons.
•
IMAGE MOVE : You can view the special area
image on the PIP window. Use , ,
or
button to view the live image of the special area.
•
IMG SIZE: Use
or
button to enlarge or
reduce the size of image on the PIP window. This
function is activated with digital zoom function.
Select the [STABILIZER] option and set to ON or OFF.
If you set the [STABILIZER] to ON, the Digital zoom is set to
[x1.1] automatically.
USER TITLE
You can use the camera identification to assign a number
and character to the camera (0 to 9, A to Z, a to z).
To disappear the user title, select [OFF].
1.
Select the [USER TITLE] option on the [SPECIAL] screen.
2.
Use
or
button to select [ON] then click
ton. The USER TITLE menu appears.
but-
63
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 63
11. 2. 25. �� 11:01
Operation and settings
Reset setting
A
3.
Use , ,
or
number then click
button to select a character or
button.
1.
Select the [RESET] option.
•
CLR: Clear all entered characters and numbers.
2.
Click
•
POS: Move the USER TITLE position on the screen
using the arrow buttons.
3.
Use
•
END: Confirm your selection or exit the setting.
•
A(Blank): Insert a space at the cursor position.
•
/
: Moves cursor to left or right.
4.
button and the RESET menu appears.
or
button to select option.
•
CAMERA REBOOT: Reboot the camera system.
•
FACTORY RESET: Clear certain settings and information and return to factory default settings.
Click
button to confirm your selection.
LANGUAGE
Select the viewer language for the camera setup menu and
OSD information display.
64
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 64
11. 2. 25. �� 11:01
Troubleshooting
This section provides useful information to help you to
resolve any difficulty you might have with your LG IP device.
Fault symptoms, possible causes and remedial actions are
provided here.
IP Setting problems
•
ARP/Ping: Disconnect and reconnect the power to the
network camera. The device should get the IP within
2 minutes.
•
Ping your camera: Open the command prompt on
your computer, type ping with the IP address of the
network device. The reply obtained by this command
provides explanation for the cause of the problem.
it is not used by anyone and the network device
can obtain this.
•
IP Conflicts: If the LG network device is set with a static
IP address and if the DHCP option is set then there
may be IP’s same as the network device and other network partner. Hence set the static IP address to 0.0.0.0
to resolve this conflict.
Cannot access the camera from browser:
•
Reconnect the network camera with power and check
the ping operation to know if the IP is used by others.
•
1. bytes = 32 time = 2 ms indicates that the IP
address is already used and cannot reuse the
same. A new IP address needs to be obtained.
Disable the proxy setting in the Browser if you are
using a proxy server.
•
Check for proper cabling and network connections, try
to ping after verifying the connectivity.
2.
•
Sometimes when HTTPS is enabled, we would be
checking the URL with http, in this case manually
change the URL to the http/https accordingly.
•
Verify the DNS and Gateway settings if the IP address
is assigned statically to the network device.
3.
Destination host unreachable: indicates that the
network device and your computer do not fall
in the same subnet hence needs to get a new IP
address. Contact the system administrator for the
required help.
Request timed out: Indicates that the IP is free as
65
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 65
11. 2. 25. �� 11:01
Troubleshooting
Accessing camera external to the local network
•
Firewall Protection: Check for the internet firewall with
the system administrator, either he has to do port forwarding or modify the DMZ function on the router.
•
Default router needed: Check if you need configure
the router settings.
Sporadic network performance
•
Network Switches or hubs used may be of the lower
configuration and the load on this may not meet the
required conditions of our network camera.
•
Check for the RJ-45 cables that are used for the network connectivity.
•
If POE is used check if the power is got by the network
camera when connected to it.
Login Password lost
•
Reset the camera by pressing the Reset button for
more than 3 seconds to restore default settings.
•
After the factory settings login using the default username and password.
Video Streaming problems
•
If the video streaming does not start on the Web
browser, install the LG Web Client ActiveX program on
your computer following the instructions on the Web
browser.
•
When Windows IE browsers are used always take care
to allow pop ups, check this option before we run the
web client.
•
Check the quality of image by referring the video settings as described in the manual.
•
Sometimes there would be intermittent or very slow
video streaming, this may be because of the higher
resolution and frame rate that are set for the video.
•
The video streaming may appear poor at times, this
may be because of the network traffic ,too many
devices connected to the switch or hub, enabling
motion detection to each of the video streams and
because of other programs running on your computer.
•
If the images appear to be blurred adjust the focus of
the network camera to get a clear image.
66
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 66
11. 2. 25. �� 11:01
Troubleshooting
Audio condition
•
The client computer that is interacting with the camera needs to have a sound card that is functional to
support speaker and microphone.
•
Video images if appear white and black adjust the settings in the OSD to get back the colorful image.
•
Select the Night mode if the network camera is connected at a place where surrounding light is less or
dark.
•
•
If we obtain lower frame rate than set we need to
check from the system administrator for sufficient
bandwidth available or reduce the number of applications running on the client computer.
The sound card needs to be checked for its support for
full duplex communication.
•
Ensure that the mute button of the client computer is
not set and all the audio settings are correct.
If the client PC’s are unable to access the multicast
stream, check with the system administrator for the
use of a valid multicast address or check if the router is
supporting multicasting.
•
Speaker button on the web viewer should be enabled
to listen the audio from the network camera.
•
Ensure that the bidirectional audio button is enabled
on the Web viewer and the microphone is set.
•
Change the input and the output gain for microphone
and the speaker respectively to set correct audio level.
•
•
If the images appear to have white of gray stripes on
it, upgrade the Video graphics driver on the client PC
to the latest version.
•
Video images may be noisy if you are using the camera in a very low light environment or the bit rate/
quality is set to very low values. Provide higher values
for quality and support the surrounding environment
with enough light.
For all further support please contact the supplier or forums
or websites.
67
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 67
11. 2. 25. �� 11:01
Open source software notice
The following GPL executables and LGPL libraries used in
this product are subject to the GPL2.0/LGPL2.1 License
Agreements:
You can obtain a copy of the GPL, LGPL licenses from http://
www.gnu.org/licenses/old-licenses/gpl-2.0.html and http://
www.gnu.org/licenses/old-licenses/lgpl-2.1.html.
GPL EXECUTABLES:
This product includes mDNSResponder component which
is licensed under the terms of the Apache License, Version
2.0.
Linux kernel 2.6, bash, busybox, gdbm, libreadline, moduleinit-tools, mount, mtd-utils, net-tools, quftp, tar, util-linux
You can obtain a copy of the Apache license from http://
www.apache.org/licenses/LICENSE-2.0.html.
LGPL LIBRARIES:
Glibc, libelf, libesmtp, live.media
LG Electronics offers to provide source code to you on
CD-ROM for a charge covering the cost of performing such
distribution, such as the cost of media, shipping and handling upon e-mail request to LG Electronics at:
opensource@lge.com
This offer is valid for a period of three (3) years from the
date of the distribution of this product by LG Electronics.
68
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 68
11. 2. 25. �� 11:01
Open source software notice
This product includes
•
dhcp client :
•
ntpdate : Copyright © David L. Mills 1992-2006
•
OpenSSL :
Copyright © 2004-2008 by Internet Systems
Consortium, Inc. (“ISC”)
>>
Copyright © 1995-2003 by Internet Software
Consortium
•
expat library : Copyright © 2006 expat maintainers.
•
libcap
•
libjpeg : Independent JPEG Group Copyright ©
1991 1998, Thomas G. Lane.
•
libmd5 : Copyright © 2002 Aladdin Enterprises.
•
libncurses : Copyright © 1998,2002 Free Software
Foundation, Inc.
•
libpcre : Copyright © 1997-2009 University of
Cambridge
•
libxml2 : Copyright © 1998-2003 Daniel Veillard.
•
lighttpd : Copyright © 2004, Jan Kneschke, incremental
•
•
cryptographic software written by Eric Young
(eay@cryptsoft.com).
>> software written by Tim Hudson (tjh@cryptsoft.com).
>> software developed by the OpenSSL Project
for use in the OpenSSL Toolkit. (http://www.
openssl.org)
PHP software, freely available from http://www.
php.net/software/ : Copyright © 1999 - 2009 The
PHP Group.
Speex :
>>
>>
>>
>>
>>
>>
Copyright 2002-2008 Xiph.org Foundation
Copyright 2002-2008 Jean-Marc Valin
Copyright 2005-2007 Analog Devices Inc.
Copyright 2005-2008 Commonwealth
Scientific and Industrial Research
Organisation (CSIRO)
Copyright 1993, 2002, 2006 David Rowe
Copyright 2003 EpicGames
69
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 69
11. 2. 25. �� 11:01
Open source software notice
>>
•
Copyright 1992-1994 Jutta Degener, Carsten
Bormann
Zlib : Copyright © 1995-2002 Jean-loup Gailly and
Mark Adler.
OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT
OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE
OR OTHER DEALINGS IN THE SOFTWARE.
All rights reserved.
Permission is hereby granted, free of charge, to any person
obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without
restriction, including without limitation the rights to use,
copy, modify, merge, publish, distribute, sublicense, and/or
sell copies of the Software, and to permit persons to whom
the Software is furnished to do so, subject to the following
conditions:
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY
OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS
OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION
70
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 70
11. 2. 25. �� 11:01
Specification
ITEM
Camera
LW342
Image Sensor
Lens
Illumination
Video
LW345
6.49 mm Progressive Scan CMOS (2 Mega Pixels)
DC-Iris, CS Mountable
Color
2 lx (F1.4, Gain : High)
B/W
0.1 lx (F1.4, Gain : High)
Resolution
Up to 1 920 x 1 072
Day/Night
ICR
WDR
Support
Image Enhancement
Backlight Compensation, 3D-DNR, Exposure Control, Sens Up Control, AGC,
White Balance, Privacy Masking, EIS, Sharpness, Digital Zoom
Video Out
RJ-45 (Network), RCA (Installation)
Compression
H.264, MJPEG
Frame Rate (Max)
30 fps @ 1 080p (1 920 x 1 072)
Multi-Streaming
Dual Streaming
71
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 71
11. 2. 25. �� 11:01
Specification
Audio
Event
Video
Analytics
Network
Audio In/Out
1/1 (Line level input / output)
Compression
G.711, G.726
2-way Audio
Support
Alarm In/Out
1/1
Motion Detection
Support
Event Notification
Relay Out, Email, FTP
Pre Event Buffering
Support
Intruder Detection
Not support
Support
Crossing Line
Not support
Support
Object Removal
Not support
Support
Object Counting
Not support
Support
Tampering
Not support
Support
Ethernet
10/100 Ethernet
Security
Password Protection, HTTPS(SSL, TLS)
Protocol
TCP/IP(IPv4), HTTP, HTTPS, RTP, RTSP, UDP, DHCP, FTP, SMTP, NTP, ARP, ICMP,
DDNS(LG)
72
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 72
11. 2. 25. �� 11:01
Specification
Management
Misc.
Integrated Client
LSS464 with 64ch recording and monitoring feature
Simple Web Client
Live monitoring and system management for a device
System Update
LSS464 or Web Client
Connections
Up to 10
Power Source
PoE (IEEE 802.3af ), DC 12 V (±20 %)
Power consumption
<7W
Input current
DC 12 V : < Maximum 580 mA
PoE : < Maximum 210 mA
Operating Temperature
-10 °C to 50 °C
Operating Humidity
0 % RH to 80 % RH
Weight
508 g
Dimension (W x H x D)
57.2 mm x 68 mm x 149 mm
73
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 73
11. 2. 25. �� 11:01
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 74
11. 2. 25. �� 11:01
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 75
11. 2. 25. �� 11:01
BZ03
LW342-FN_FP.COMMON_V1.0_MFL62591948_ENG.indd 76
11. 2. 25. �� 11:01
Download PDF