LG LS-H366NLD0 Owner's manual
Add to my manuals20 Pages
LG LS-H366NLD0 room air conditioner offers various features for cooling and heating your home. With its energy-saving operation, you can enjoy a comfortable indoor climate without worrying about high energy consumption. The unit also features an automatic restart function that restores previous settings after a power outage.
advertisement
▼
Scroll to page 2
of 20
Room Air Conditioner OWNER'S MANUAL ? Please read carefully and thoroughly operating this unit. this manual before ? Contact the authorized SVC man for repair or maintenance of this unit. ? Contact the installer for installation of this unit. ? The is not intended for use by young infirm persons without supervision. children should be supervised to ensure appliance children ? Young that they or do not play with the Prior to appliance. installation, this air-conditioning approval by the utility service which provides electricity (EN 61000-3 Norm). unit must be submitted for Safety precautions Safety Precautions SafetyPrcuions OperatingIsuco CarendMitc Warning Caution .................................3 To before operation to the prevent injury user or other people and property damage, the instructions must be followed. following Incorrect operation damage, the seriousness is classified due to ignoring of instruction will harm cause by the following or indications. WARNING WARNING Operating Instructions Preparation ..4 This symbol indicates the possibility of death or serious possibility of or damage injury. Remote Control Features .....5 CAUTION CAUTION Mode Selection ......7 Operation This symbol indicates properties only. Additional features ..............13 the Installation Care and Maintenance Do not ....................18 Operation Tips injury to precautions WARNING WARNING Care and Maintenance .......16 ? Troubleshooting tips ? Before You Call For Service ...............19 install, Improper installation and reinstall the unit by yourself. leakage, electrical shock, or fire. Please consult authorized dealer or specialist for the installation work. Please note fault caused by improper installation is not covered by warranty. Unit must be installed in an easily accessible area. Any additional cost required to hire a special equipment to service the unit will be the responsibility of the customer. remove will cause water WARNING WARNING Plug in the power plug properly. ? Otherwise, it will electrical shock heat Do not or stop the by inserting or pulling out the power plug. ? cause or operate unit fire due to It will or generation. cause electrical shock fire due to heat Do not damage or use an unspecified power cord. ? It will ? If the generation. cause electrical shock Do not modify power length or with other ? It will cord share the outlet cause Do not operate with wet hand. Do not insert of time. This could health. a hazard. anything into the air inlet/air outlet. ? It may cause electrical shock. ? generation. Do not expose the skin directly to cool air for long ? fire. appliances. electrical shock fire due to heat periods or supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid or Troubleshtingp ................................2 damage your When an abnormality (smell of burning, etc) occurs, stop the air conditioner, and disconnect the power plug or turn off the breaker. ? If the unit continues to be in an abnormal cause a fire, damage, etc. In this case, consult your dealer. 2 operated condition, it may Since the fan rotates at high speed, this may cause an injury or damage the unit. Repair or relocation should by the customer. not be done ? If this is done incorrectly, it may fire, electric shock, injury by dropping of the unit, water cause a leakage, etc. Consult your dealer. CAUTION ? Contact the authorized Service technician for ? Contact the installer for installation of this unit. ? The air conditioner is not intended for without ? by young or maintenance of this unit. children or infirm persons supervision. children should be Young use repair to supervised ensure that they do not with the air play conditioner. CAUTION CAUTION When the air filter is to be Do not clean the air removed, do not touch the metal parts of the indoor unit. conditioner with water. ? It may ? Should be disconnected from cause an injury. ? supply When the unit is to be cleaned, switch off, Since the fan rotates at high speed during operation, may cause an injury. it Do not apply an ? a pet or This could injure the house Do not insecticide put where is a or ? damaged. The unit may drop or fall down and cause an injury. Do not step on the indoor/outdoor unit and do to direct air flow. ?Itmaycauseafireor may installation on stand which is stove, etc. exposed shortage Do not leave ? pet An oxygen stove, etc. a occur. plant. flammable spray. or put ? plant where it will be exposed to direct air flow. off the circuit breaker. ? Water may enter the unit and degrade the insulation. It may cause an electric shock. Do not and turn Ventilate well when used together with not It may affect combustion. ? deformation of the cabinet. put anything on it. It may cause an injury through dropping or falling down. Do not insert hands vanes is ? It will through when the air conditioner Do not be used for bench when injury by the ? blower. Do not use for If not, dirt may collect and fire. special Do not operate for a long time in high humidity, e.g. leaving a door Do not use this air conditioner precision devices, food, animal, plants, and art objects. to preserve It may cause quality, etc. going to long time, turn cause a purposes. ? a deterioration of ? or window open. In the cooling mode, if it is operated in a room with high humidity (80%RH or more) for a long time, water condensed in the air conditioner may drop and may wet and spoil furniture, etc. 3 step onto an unstable cleaning and/or maintaining the unit. off the circuit breaker. operationg cause an rotating When the unit is not ? It may cause an by falling down. injury, etc. ENGLISH Preparation SafetyPrcuions before operation How to Insert the Batteries Remove the battery arrow direction. Insert new battery batteries are installed Reattach the cover by pulling cover according that the making sure correctly. by sliding it it back into (+) to the and of (-) position. NOTES: ? Use 2 AAA(1.5volt) batteries. Do not use rechargeable batteries. OperatingIsuco CarendMitc Storage and Tips ? For Using ? on a To operate the room remote control at the air conditioner, aim the signal receptor. Signal Receptor Receives the signals from the remote control.(Signal receiving sound: two short beeps or one long beep.) Operation Indication Lamps On/Off Timer or : Sleep Mode Defrost Mode : : Lights Lights up up during the during Timer system operation. operation or Sleep mode. Lights up during Defrost Mode or Hot operation (Heat pump model only) Start Outdoor unit : Lights up during outdoor (Cooling model only) : Lights up during plasma-purification operation. (option) operation Plasma Mode Troubleshtingp the Remote Control The remote control may be stored mounted wall. unit operation. Auto Restart Mode : Lights Auto Restart Button : In failure of electric power, if the button is up during if Restart Button is Operation Button : Operation starts, and when this button is pressed stops when you press the button again. 4 receptor pressed. pressed the unit runs as previous setting operation when power returns. Forced Signal Operation indication lamps About the remote control The remote control transmits the signals to the on the system system. Features of the Remote Control- Door Signal 1 START/STOP BUTTON Operation starts when this button is pressed and stops when the button is pressed again. 2 OPERATION MODE SELECTION BUTTON Used to select the operation mode. 3 ROOM TEMPERATURE SETTING BUTTONS Used to select the room temperature. 4 INDOOR FAN SPEED SELECTOR Used to select fan speed in four steps low, medium, high and CHAOS. 5 JET COOL Used to start 1 6 CHAOS SWING BUTTON Used to stop or start louver movement and set the desired up/down airflow direction. 3 7 ON/OFF TIMER BUTTONS Used to set the time of starting and transmitter 5 Opened or stop the speed cooling. (Speed cooling operates super high fan speed in cooling mode.) 6 stopping operation. (See page 13) 4 10 2 8 TIME SETTING BUTTONS Used to adjust the time. (See page 9 TIMER SET/CANCEL BUTTON Used to set the timer when the desired time is obtained and to cancel the Timer CANCEL 9 7 ON OFF SET 11 12 operation. (See page 13) 8 13 14 15 16 10 SLEEP MODE AUTO BUTTON Used to set Sleep Mode Auto operation. 11 AIR CIRCULATION BUTTON Used to circulate the room air without (See page 13) or door Flip-up (opened) PLASMA(OPTIONAL) Auto Healthy Operation Dehumidification Cooling Model( RESET BUTTON Used prior to resetting time batteries. 15 Operation ), Heat Pump Model( plasma-purification HORIZONTAL AIRFLOW DIRECTION CONTROL BUTTON (NOT ON ALL MODELS) Used to set the desired horizontal airflow direction. (See page 14) 14 or after replacing 2nd F Button Used prior to using modes printed in blue at the bottom of buttons. (See page 12) 16 Heating Operation ? Used to start or stop the function. (See page 11) Mode Cooling Operation cooling heating. (See page 14) ROOM TEMPERATURE CHECKING BUTTON Used to check the room temperature. 12 13 Operation 13) ) 5 ENGLISH How to the Operation 1 Press the a 2 Start/Stop button. respond with The unit will beep. Open the door on the remote control. To select Cooling Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the 3 Close the door lower than the set within a arrow. Auto Cooling Healthy Dehumidification on Heating (Heat pump model only) the remote control. Set the room temperature temperature. The temperature can be range of 18°C~30°Cin 1°C increments. ON To raise the temperature To lower the temperature 4 Set the fan with the door speed again of the remote control still closed. You can select the fan speed in four steps- low, medium, high and CHAOS. Each time the button is fan Troubleshtingp Mode Selection button Cooling Operation SafetyPrcuions OperatingIsuco CarendMitc use Natural wind For more by the fresh CHAOS feeling CHAOS mode. In this speed according speed pressed, the mode is shifted. logic than other fan speed, press the Indoor Fan Speed Selector and set to mode, the wind blows like natural breeze by automatically changing fan to the CHAOS logic. 6 Auto Operation Press the 1 a 2 beep. Open the door on the remote control. To select Auto Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the 3 The arrow. Auto Cooling ON ENGLISH Start/Stop button. respond with The unit will Healthy Dehumidification temperature and fan speed electronic controls based on are Heating (Heat pump model only) automatically the actual room set by the temperature. If change the set temperature, press the Room Temperature Setting buttons. The cooler or warmer you feel, the more times (up to two times) you should press the button. The set temperature will be changed automatically. you want to To raise the temperature To lower the temperature During Auto Operation: You cannot switch the indoor fan If the system is not operating speed. as It has already been set desired, manually switch rule. system will not cooling mode to the heating mode, or from heating mode to cooling mode, it must be done by manually resetting. During Auto Operation, pressing the chaos swing button makes the horizontal louvers swing up and down automatically. If you want to stop auto-swing, press the chaos swing button again. automatically switch from the by the Fuzzy to another mode. The 7 Healthy Dehumidification Operation SafetyPrcuions OperatingIsuco CarendMitc Troubleshtingp Press the 1 Start/Stop button. respond with The unit will a 2 beep. Open the door the remote control. To select on Dehumidification Operation, press the Healthy Operation Mode Selection button. Each time the button is pressed, shifted in the direction of the Auto Cooling 3 Set the fan operation Healthy Dehumidification speed again mode is Heating (Heat pump model only) with the door of the remote control still closed. You can select the fan ON speed in four or time the button is pressed, Natural wind the fan mode is shifted. by the fresh CHAOS logic speed, press the Indoor Fan Selector and set to CHAOS mode. In this mode, the wind more Speed steps- CHAOS. Each low, medium, high, speed For the arrow. feeling than other fan blows like natural breeze according to the CHAOS by automatically changing logic. fan speed During Healthy Dehumidification Operation: If you select the dehumidification mode on the operation selection button, the A/C starts to run the dehumidification function. It automatically sets the room temp. and airflow volume to the best condition for dehumidification, based on In this case, however, the setting control the room temp. either. the sensed current temp. is not room displayed temp. in the remote control and you are not able to During the healthy dehumidification function, the airflow volume is automatically set according to the optimization algorithm responding to the current room temp. status which makes the room condition healthy and comfortable even in the high humidity season. 8 Heating Operation(Heat pump 1 Press the ENGLISH Start/Stop button. respond with beep. Open the door on Operation, press the remote control. To select the Each time the button Heating Operation Mode Selection button. is pressed, the operation mode is shifted in the direction of the Close the door arrow. Auto Cooling 3 only) The unit will a 2 model Healthy Dehumidification on Heating (Heat pump model only) the remote control. Set the temperature higher than the room temperature. The temperature can be set within a range of 16°C~30°Cin 1°C increments. ON To raise the temperature To lower the temperature 4 Set the fan speed again with the door of the remote control still closed. You the fan speed in four can select steps--low, medium, high and CHAOS. Each time the button pressed, the fan speed mode is shifted. Natural wind For more by the fresh CHAOS feeling CHAOS mode. In this speed according is logic than other fan speed, press the Indoor Fan Speed Selector and set to mode, the wind blows like natural breeze by automatically changing fan to the CHAOS logic. 9 Jet Cool SafetyPrcuions Operation 1 Press the a OperatingIsuco CarendMitc 2 beep. Press the Jet Cool button to the will on 3 Start/Stop button. respond with The unit will speed cooling operate mode and the unit operate in super high fan speed cooling mode for 30 minutes. To cancel the Jet Cool mode, press the Jet Cool button or room temperature setting button again and the unit will operate in high fan speed on cooling the fan speed button or the mode. or or NOTE: Troubleshtingp During the JET COOL function at any moment, the A/C starts to blow the cool air at extremely high speed for 30 minutes setting the room temp. automatically to 18°C. It is especially used to cool the room temp. in the shortest time in a hot summer. In heat pump mode or neuro fuzzy mode, however, the JET COOL function is not available. In order to return to the normal either the or operation the JET COOL button mode from the JET COOL mode, you just press button, airflow volume selection or temp. setting button cooling mode selection again. 10 PLASMA Purification 1 Operation(Optional) Press the ENGLISH Start/Stop button. respond with a The unit will beep. 2 3 Open the door on the remote control. Press the PLASMA air purifying operation ON/OFF button. Operation will start when the button is pressed and stop when the button is pressed again. Set the fan speed again closed. You with door of the remote control speed in four steps-low, medium, high or CHAOS. Each time the button is pressed, the fan speed mode is shifted. can select the fan Air purifying operation (PLASMA) can be cooling, Heating or any other operations. PLASMA Air with Purifying Operation only If you press the only PLASMA button, PLASMA air purifying operates. only Then, fan speed is low. You can select the fan speed in four steps-low, medium, high or CHAOS. Each time the button speed 11 ( mode is shifted. ) is pressed, the fan 2nd F SafetyPrcuions OperatingIsuco CarendMitc Troubleshtingp Operation 1 Press the a 2 Start/Stop button. respond with The unit will beep. Open the door of the remote control and press the 2nd operate functions printed in blue at bottom Function button to of buttons. (Check the display.) indication of 2nd function These buttons on operate the timer setting remote control as follows: CANCEL ON OFF SET CANCEL ON OFF SET 3 2nd function goes off in the button is a short time automatically or when pressed again. For more details, refer to functions next page. 12 Additional features Mode Sleep 1 Press the Sleep To cancel the Sleep Mode, press the sleep Mode Auto button several times until the star Mode Auto button to set the time you want the unit to turn off automatically. ( 2 programmed in one-hour by pressing the Sleep Mode ) disappears increments Auto The Sleep Mode will be operated at speed (cooling) or medium fan speed (heat pump only) for quiet sleeping. the Sleep slow fan mode is available for 1 to 7 times. To sleep alter the time in period steps of Mode Button while 1 hour, press aiming IN COOLING MODE OR HEALTHY at air DEHUMIDIFICATION MODE: conditioner. The Make sure the Sleep Mode Auto LED Setting the 1 operation display. Note: The button 1 to 7 times. 3 from the The Timer is lights over up. temperature will automatically rise by 1°C the next 30 minutes and for comfortable sleeping. Press the Time Setting by 2°C in 1 hour Time Time can be set only when you have pressed the Reset button. If you have just replaced the batteries, the Reset button should be pressed 3 buttons until the desired time is set. to reset the time. Press the Start/Stop button. Press the Timer SET button. 4 CANCEL Press 2nd F button 2 SET and check if 2nd F icon is Note: Check the indicator on. for A.M. and P.M. Delay Start/Pre-Set Stop 1 2 3 Make sure the time is set remote control correctly on the To set the selected 5 display. Press 2nd F button. SET receptor. Press the ON/OFF Timer buttons to turn Timer CANCEL time, press the Timer SET button while aiming the remote control at the signal To cancel the timer ON off. on or OFF CANCEL setting Check if 2nd F icon is off. Press the Timer Cancel button while 4 Press the Time ET Setting buttons until the desired aiming remote control at the signal receptor. time is set. (The timer lamp on the display will go out.) air conditioner and the NOTE: Select one of the following four types of operation. with the unit Delay OFF Timer Delay ON Timer Delay 13 running OFF and ON Timer Delay ON and OFF Timer ENGLISH Vertical Airflow Direction Control SafetyPrcuions The up/down airflow (Vertical Airflow) adjusted by using the remote control. Troubleshtingp Note: If you press the CHAOS swing button, the horizontal airflow direction is changed automatically based on the CHAOS algorithm to distribute the air in the room evenly and at the same time to make the human body comfortable, as if enjoying a natural breeze. Always use the remote control to adjust the up/down airflow direction. Manually moving the vertical airflow direction louver by hand could damage the air feel most Press the 1 OperatingIsuco CarendMitc be can conditioner. button to start the unit. Start/Stop When the unit is shut off, the up/down airflow direction system. louver will close the air outlet vent of the Open 2 the door Press Chaos on To the remote control. Swing adjust left/right(Horizontal Airflow) direction Caution button and the louvers will swing off before desired airflow direction. control. up and down. Press the Chaos Swing button again to set the vertical louver at the : Ensure unit is turned adjusting the horizontal airflow direction Carefully louver to allow open vertical to the access horizontal airflow direction. Adjust the left/right Horizontal Airflow Direction Control The left/right(Horizontal Airflow) can be adjusted by using Press the Start/Stop button to start the unit. Open the door on the Start/Stop button and airflow direction by hand. (Option) the remote control. remote control. Press the Airflow Direction the louvers will swing left and the Horizontal Airflow Direction Control Button right. again Press to set the horizontal louver at the desired airflow direction. Air Circulation Mode Circulates the 1 2 Press the Open room Start/Stop the door on air without cooling or button. the unit will heating. respond with a beep. the remote control. Press the Air Circulation button. Close the door remote control. Now each time that you press the Indoor Fan shifted from low to CHAOS and back to low again. CHAOS Air Fan speed is on low. Fan speed is on medium. Note: CHAOS Air economizes power consumption and prevents overcooling. The fan from high to low or vice versa, depending on the ambient temperature. 14 the fan Speed Selector, speed Fan is speed is on the speed on is high. automatically changed The Button Operation ENGLISH FORCED OPERATION The operation pressed. will be started if the power button is If you want to stop operation, re-press the button. FORCED OPERATION Cooling Model Operating mode Indoor FAN Speed Setting Temperature Heat pump Model Room Temp. ≥ 24°C2 1 °C ≤ Room Cooling Cooling High High Healthy Temp. < 24°C case Dehumidification Rule High 22°C2 2 °C2 3 °C2 4 °C the power comes on again after a power failure, Auto Restarting Operation is the function to operate procedures automatically to the previous operating Temp. < 21°C Heating Auto restart In Room Dehumidification Healthy conditions. If you want to use this Restart Button. operation, press the Auto AUTO RESTART Helpful information Fan speed and cooling capacity. cooling capacity indicated in the specification is the value when the fan speed is set to high, and the capacity will be lower at low or medium fan speed. High fan speed is recommended when you wish to cool the room quickly. The 15 High Speed Care and maintenance of the air conditioner SafetyPrcuions OperatingIsuco CarendMitc CAUTION: Before performing any maintenance, turn off the main power to the system. Indoor Unit Never Grille, Case, and Remote Control ? Turn the system off before cleaning. To clean, wipe with a soft, dry cloth. Do not use bleach or use any of the followings: Water hotter than 40°C Could deformation and/or cause discoloration. abrasives. ? Volatile substances NOTE: Could Supply power must be disconnected before cleaning the indoor unit. conditioner. the surfaces of the air damage Powder Gasoline Air inlet vent Air filters Air outlet vent (behind front panel) Vertical louver Horizontal louver 1 Lift the front slightly AIR FILTER The air filters behind the front checked and cleaned once grille should be every 2 weeks or more 2 often if neccessary. access forward to panel remove Clean the filter with and the filter tab pull the filter. a vacuum or warm, soapy water. ? If dirt is conspicuous, wash with a detergent in lukewarm water. water (40°C or more) is used, it solution of ? If hot may be deformed. 3 After washing with water, dry well in the shade. 4 30k/32k Re-install the air filter. 36K/38k PLASMA FILTER, DEODORIZER 1 FILTER(OPTION) The PLASMA filter behind the air filters should be checked and cleaned once every 3 months or more 2 After removing forward to Dip 4 filters, pull slightly the PLASMA filter. the PLASMA filter into the water mixed with neutral often if necessary. 3 the air remove detergent, for 20~30minutes. Dry the PLASMA filter in the shade for a day (Especially, the humidity must be removed perfectly on this parts). Note the cuts of electric discharge lines. DEODORIZER Filter Troubleshtingp 5 PLASMA Filter 1 Don't touch this PLASMA Filter within 10 seconds after cause an opening the inlet grille, it may electric shock. 2 3 16 Re-install the PLASMA filter to the original position. After removing the air forward to remove in the sunlight Dry filters, pull slightly the DEODORIZER filter. for two hours. Re-install the DEODORIZER filter to the original position. Replacement of Purifying Filter(Option) ? Recomended 1 Open use period front panel : About 2 years and remove air 2 Remove air 3 Insert purifying ENGLISH filters. filters. new air purifying filters. Air filter 2 3 4 Reinsert air filters and close front panel. Air purifying filter Outdoor Unit The heat exchanger coils and panel vents of the outdoor unit should be checked regularly. If clogged with dirt or soot, the heat exchanger and panel vents may be professionally steam cleaned. (Side) (Rear) Air intake vents Piping Air outlet vents NOTE: Dirty or clogged coils will reduce the operating efficiency of the system and higher operating costs. cause (Side) (Rear) Air intake vents Air outlet vents 17 Piping SafetyPrcuions OperatingIsuco CarendMitc Troubleshtingp When the air conditioner is not going to be used for a long time. When air conditioner is not used for to be going When the air conditioner is to be used long time. a Clean the air filter and install it in the indoor Operate the air conditioner on Air circulation mode (Refer to page 14) for 2 to 3 hours. unit. (Refer to page ? This will dry 16 for cleaning filters.) out the internal mechanisms. Turn off the circuit the again. breaker, and disconnect plug. Check that the air inlet and outlet of the CAUTION CAUTION indoor/outdoor unit are not blocked. Turn off the circuit breaker when the air conditioner is not going to be used for a long time. Dirt may collect and may cause a fire. Remove the batteries from the remote control. Operation Tips Do not overcool the room. Keep blinds or curtains closed. This is not good for the electricity. health and wastes Keep the Do not let direct sunshine enter Adjust the horizontal airflow direction to room when the air operation. ensure a in the Make sure that the doors are Avoid doors and opening windows to keep as much shut as Clean the air filter regularly. tight. the cool air in the room. vertical and uniform temperature room. Ventilate the room occasionally. Blockages possible temperature the conditioner is in and windows room uniform. in the air filter reduce the airflow and lower cooling and dehumidifying effects. Clean at least every two weeks. 18 once Since windows it is are kept closed, idea to open them and ventilate the room now and a then. good Before you call for service... Troubleshooting Tips! Save ? Check the following points contact your dealer or before ? operate. ? a service.... If the fault peculiar ? odor. persists, please See page Have you made a mistake in timer operation? Has the fuse blown or has the circuit breaker been has or Explanation The air conditioner does not room requesting repairs money! service center. Case The time and tripped? - Check that this is not the 13 a damp walls, carpet, furniture, or smell exuded by cloth items in the - room. It is seems that condensation leaking ? from the air Condensation occurs when the airflow from the air conditioner cools the warm room air. - conditioner. Air conditioner does not ? This is the operate for about ? Wait about three minutes and 3 minutes when restarted. Does not cool or protector of the mechanism. operation will heat ? Is the air filter dirty? See air filter cleaning 16 instructions. effectively. ? Has the ? Are the indoor unit's air inlet temperature been set incorrectly? or The air conditioner is ? For a - noise that sounds like water -This is the sound of freon noisy. 7, 10 outlet vents obstructed? operation - begin. flowing flowing. inside the air conditioner unit. ? For noise that sounds like the compressed atmosphere. -This is the sound of the dehumidifying water being processed inside the air conditioning air a releasing into - unit. Remote control ? Are the batteries faint, ? Are the batteries inserted in the or no display is display at all. and Crack sound is heard. ? (-) depleted? opposite (+) 4 directions? This sound is generated by the expansion/constriction of the front panel, due to changes of temperature. 19 etc. - ENGLISH Memo 20
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project