LG | LNV7210R | Quick Start Guide | LG LNV7210R Owner's manual

LG LNV7210R Owner's manual
Specification
Item
OWNER’S MANUAL
High
Definition
Network
Camera
Video /
Audio
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
LNV7210 series
LNV7210R series
*MFL69458110*
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
•
A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this
product in the end user.
•
Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces
or shall be provided with brushings.
Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.
Warning: Please adopt the power adapter which can meet the safety extra low voltage (SELV)
standard. And source with DC 12 V or
AC 24 V (depending on models) according to the IEC60950-1 and Limited Power Source standard.
Event
LNV7210 series
6.4 mm (1/2.8 Type) CMOS
Lens Type
3 mm to 9 mm F1.2 (x3 Zoom)
Day / Night
ICR (Auto / Day / Night / External / Schedule)
Minimum
Illumination
Camera
LNV7210R series
Image Device
WDR
Interface
Color: 0.03 lx @ F1.2 (1/30 sec, 50 IRE)
B/W: 0.003 lx @ F1.2
(1/30 sec, 50 IRE)
B/W: 0 lx @ IR LED on
Analog Out
BNC out
Audio In / Out
1/1
Alarm In / Out
1 In / 1 Out
SD Slot
micro SD (Up to 32 GB)
Ethernet
RJ-45 10 / 100 BASE-T
Security
Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X
Open Protocol
ONVIF 2.2 Profile S, PSIA 1.1
Protocol
IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP,
QoS, UPnP
Support
Network
IR Distance
(LNV7210R only)
20 m
Image
Enhancement
Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control,
AGC, White Balance, Privacy Masking, Sharpness, EIS, Pivot,
SmartIR (LNV7210R only)
Integrated
Software
LG Ipsolute VMS Suite / Mobile application (iPhone, iPad,
Android)
Compression
H.264, H.264_High, MJPEG
Connections
Up to 20
Resolution
1920 x 1080 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)
Power Source
DC 12 V, PoE
Maximum Frame
Rate
60 fps @ 1920 x 1080
Maximum Power
Consumption
8.7 W (DC 12 V), 10.4 W (PoE 48 V)
Multi-Streaming
Up to 4
Maximum Input
Current
730 mA (DC 12 V), 280 mA (PoE)
ROI (Region of
Interest)
Smart codec (Up to 8)
-10 ºC to 50 ºC / 0 % RH to 80 % RH
Video Analytics
Motion detection, Tampering alarm, Face detection, Intrusion
detection, Crossing line, Object counting, Object removal, Object
desertion
Operation
Temperature /
Humidity
Protection
IK10, IP66
Dimension
(Ø x H)
140 mm x 122 mm
Weight
957 g
IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
General
Text Overlay
Support
Audio
Compression
G.711, G.726
2-way Audio
Support
Audio Detection
Support
Event Trigger
Video analytics, Audio detection, Alarm input
Event Notification
Relay Out, Email, FTP
Pre Event
Buffering
Support
950 g
Note that design and specification of this unit may change from the manual as quality and
improvement without prior notice.
Warning: Install the camera on a ceiling or wall
where can withstand the weight of 5 times of
the camera including mounting bracket.
Caution: This installation shall be made by a
qualified service person and shall conform to
all local codes.
Caution: To avoid electrical shock, do not
open the cabinet. Refer servicing to qualified
personnel only.
Caution: The apparatus shall not be exposed
to water (dripping or splashing) and no objects
filled with liquids, such as vases, shall be placed
on the apparatus.
Caution: Make sure the power supply voltage
is correct before using the camera.
Caution: Do not drop the camera or subject it
to physical shock.
Caution: The sensor may be burned out by
a laser beam, so when any laser equipment is
being used, make sure that the surface of the
sensor not be exposed to the laser beam.
Caution: While shipping, the camera should be
packed in its original packing.
Caution: It is permitted to use ancillary
equipment (e.g. A UPS) to prevent the damage
from mains supply voltage reductions.
Disposal of your old appliance
Note:
Please make sure the product is installed
appropriate places where secured from flood,
such as under the eaves, to operate properly.
This product is certified as IP66 standard.
However, if there is any flood concerns, it
is highly recommended to use an outdoor
Housing. When you install the camera inside
an outdoor Housing, please use one of the
following methods:
1. Remove the front glass of Housing before
installing the camera.
2. To keep the front glass of Housing, remove
the front cover, and then put the camera
close to the front glass.
EuSP Ltd.
Herald Way Pegasus Business Park
Castle Donington, DE74 2TZ United Kingdom
1.
2.
3.
This crossed-out
wheeled bin symbol
indicates that waste
electrical and electronic
products (WEEE)
should be disposed
of separately from the
municipal waste stream.
Old electrical products can contain
hazardous substances so correct disposal
of your old appliance will help prevent
potential negative consequences for the
environment and human health. Your old
appliance may contain reusable parts that
could be used to repair other products,
and other valuable materials that can be
recycled to conserve limited resources.
You can take your appliance either to the
shop where you purchased the product,
or contact your local government waste
office for details of your nearest authorised
WEEE collection point. For the most up to
date information for your country please
see www.lg.com/global/recycling
Components
Camera, CD (Software and Owner’s Manual), Installation Manual, Test monitor cable, Wrench,
Screws (4 EA), Installation sticker, Camera mounting bracket
Important Safety
Instructions
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of
the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
Handling of the unit
Be careful not to spill water or other liquids on
the unit. Be cautious not to get combustible or
metallic material inside the body. If used with
foreign matter inside, the camera is liable to fail
or to get cause of fire or electric shock.
•
Remove dust or dirt on the surface of the
lens with a blower.
•
Use a soft and lint-free, dry cloth(such as
glass cleaner) to clean the body. If it is
very dirty, use a cloth dampened with a
small quantity of neutral detergent then
wipe dry.
•
Avoid the use of volatile solvents such
as thinners, alcohol, benzene and
insecticides.
They may damage the surface finish and/
or impair the operation of the camera.
•
This camera is designed for mounting on
the ceiling or wall. If you install this camera
upside down, it may cause malfunction.
Operating and storage
location
Avoid viewing a very bright object (such as
light fittings) during an extended period. Avoid
operating or storing the unit in the following
locations.
•
Extremely hot or cold places (operating
temperature -10 °C to 50 °C, however, we
recommend that the unit be used within a
temperature range of 0 °C to 45 °C)
•
Damp or dust place
•
Places exposed to rain
•
Places subject to strong vibration
•
Close to generators of powerful
electromagnetic radiation such as radio or
TV transmitters.
•
Do not use the camera in such place
where rapid temperature fluctuation by
switching an air conditioner on and off.
Part Names and Functions
Connection
a Dome Cover
Precautions
Connecting Power Source
b IR Sensor (LNV7210R only)
•
Be sure to switch off the unit before
installation and connection.
Connect power, using one of the methods
listed below:
•
The installation should be made by
qualified service personnel or system
installers.
To use the power adapter
c IR LED (LNV7210R only)
a
NOTE:
Do not stare at operating IR LED within hazard distances (1 m).
d micro SD card slot
•
Insert the micro SD card.
e Jog button
Use this button for control the Zoom / Focus of the camera.
f Video Out Connector
Use this jack for checking the picture with portable monitor when install the camera.
g RESET button
b
c
Push the button more than 3 seconds, this would restore the factory default network related
settings.
h AUDIO IN / OUT (Line Level Input/ Output)
Connecting Alarm Device
NOTE:
•
When the connecting Alarm and Audio,
tighten the screws as shown above.
•
Put your finger between the power
connector and the camera body to pull
out the connector.
j Power input terminal
Connects to a DC 12 V power supply using proper cables. This camera must always be
operated a DC 12 V. Certified/Listed Adaptor which comply with LPS.
k ETHERNET / PoE Port
PoE Device
(IEEE802.3af )
NOTE:
If the camera doesn’t work properly after
connecting PoE device, please check if the PoE
device supplies enough power.
You can control and monitor the system via
network. With the remote control (monitoring),
you can change the system configuration
or monitor the image via network. After the
installation, check the network settings for the
remote control and monitoring work.
Connect the IP camera to your network using a
standard RJ-45 network cable as shown below.
Provides physical interface for sensor and Alarm/Relay.
Alarm terminals are used to connect the alarm
(relay) devices such as sensors, door switches,
etc.
Connecting Microphone and
Speaker Device
Optionally connect an active speaker and/or
external microphone with a built-in amplifier.
ALARM IN & OUT / ALARM IN & OUT RETURN
(Sensor Input / Relay Output)
Connect the sensor device and alarm (relay)
device to the alarm terminal. Alarm signal is
outputted at an event occurrence.
AUDIO OUT
PoE Device
(IEEE802.3af )
Connects to a PC or a network via a hub with a 10 BASE-T / 100 BASE-TX cable attached
RJ-45 connector.
Broadband
Service
NOTE:
Power over Ethernet (PoE) is a technology that integrates power into a standard LAN
infrastructure. It enables power to be provided to the network device, such as a network
camera, using the same cable as that used for network connection. It eliminates the need for
power outlets at the device locations and enables easier application of uninterruptible power
supplies (LPS).
l
Connect a DC 12 V power source to the power
input terminal as shown below.
(recommended power adapter is DC 12 V / 1.5
A or above)
Connecting Network
i ALARM IN & OUT / ALARM IN & OUT RETURN
h i jk
d
e
f
g
Do not expose the power and connection
cables to moisture, which may cause
damage to the unit.
NOTE:
•
The Photo MOS Relay is rated for 100 mA
at DC 20 V or 100 mA at AC 28 V.
•
Grasp both ends of the 3 or 4 pin
connector plug and then sway both side
to pull it out.
Broadband
Service
l Camera mounting bracket
AUDIO IN
Alarm (relay)
Device
Router
To use the PoE (Power over Ethernet)
device
Sensor
Device
Connect the PoE cable to the LAN port on the
unit. You must use the “IEEE802.3af” standard
PoE device.
NOTE:
Keep the microphone away from the speaker
to avoid howling.
You can lock the camera mounting bracket by tighten the screws.
Installation
Using the micro SD card
You can record your surveillance environment with the micro SD
card even if the network is disconnected condition.
Remove the micro SD card
1.
Press the back end of the micro SD card to release the lock
condition.
To insert the micro SD card
1.
Remove the Dome Cover.
2.
Insert the micro SD card carefully as shown in the following
illustrations. Make sure the micro SD card terminal position
before insert the micro SD card. Push the back end of the
micro SD card to fix it at the last step.
Mounting the camera
3.
Connect the cables to the cable jacks of the camera body.
Follow the instructions below to surface mount the camera with
supplied camera mounting bracket.
1.
Use the installation guide template to check the mounting
location. Face the front of the label toward the area of
interest. Using the template as a guide, make a hole
through the ceiling.
2.
Install the camera mounting bracket to the ceiling.
4.
Assemble the camera and the housing. Make sure when
you assemble the camera in the right direction. Lock the
camera mounting bracket by tighten the fixing screw.
NOTE:
•
Adjust the position of [ALIGN] arrow, to the hole at the
bottom of camera.
Then push and turn in the direction of the [LOCK] arrow.
•
Arrange the cables by cable tie after installation.
Camera Adjustment
2.
NOTE:
•
Do not use the power too much when you insert the micro
SD card. The micro SD card may be damaged.
•
If you insert the micro SD card in the wrong position,
the micro SD card may be damaged or it may cause the
malfunction of the micro SD Card Slot.
•
Keep the terminal part of the micro SD card in clean. Be
careful the terminal part of the micro SD card not to dusty.
•
As the micro SD card is consumable, the micro SD card end
its days and may be not able to save data if you use it more
than over certain times. In this case, replace micro SD card
to buy a new one.
*MFL69458110*
Adjust the rotation position of the camera.
Take the micro SD card out carefully from the camera. It
may cause a malfunction of the micro SD card or the micro
SD card slot if you use the power too much at lock status.
CAUTION:
•
If you install the micro SD card on the camera and remove
with the micro SD card condition indicator lights on, you
must unmount the micro SD card by using the [System >
Storage > Device Management > Unmount] menu. The
micro SD card data is compromised or the camera may
not operate normally, if you remove the card without use
[Unmount] function.
•
LG Electronics is not responsible for deleted data caused
by user mishandling when you insert or remove the micro
SD card.
Recommended the micro SD card specification
Maker
LG
Sandisk
Transcend
Capacity
Block Size (FAT 32)
Less than
32 GB
32 kbyte
NOTE:
Speed of reading and writing more than 10 MB/Sec. (Class 6)
Fixing Screw
NOTE:
Push the cap from inside to arrange the cables through the
conduit. (Optional)
ROTATION
NOTE:
•
When you assemble the dome cover, make sure the SD
card PCB position is aligned with the LG logo.
•
The camera could be damaged by adjusting Pan, Tilt by
force.
•
PAN: 350° / TILT: 75° / ROTATION: 355°
•
When you adjust PAN/TILT/ROTATION manually,
be careful your hand is not to hurt by protrusions of other
part.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising