LG | LVC-D10NC | Owner's Manual | LG LVC-D100NP Owner's manual

LG LVC-D100NP Owner's manual
Operating
Instructions
LVC-D10NE
LVC-D10NC
LVC-D100NM
LVC-D100NP
Before
please
the camera,
read these instructions thoroughly
installing
and
using
and retain them for later reference.
Regulatory
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION TO REDUCE THE RISK OF
ELECTRIC
SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS
INSIDE,
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This
symbol
is intended to alert the
user
to the presence of
uninsulated
"dangerous voltage"
within the product's enclosure that
may be of sufficient magnitude to
constitute
a
risk of electric shock to
persons.
The exclamation
point within an
equilateral triangle is intended to
alert the
user
to the presence of
important operating and
maintenance (servicing)
the
or
or
radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
?
Expose
to
exposed dripping
no object filled with liquids, such
be placed on the apparatus.
To avoid electrical
Wiring
and used in accordance with the instructions, may cause harmful interference to
Moisture.
Apparatus
splashing and
servicing
equipment generates, uses and can radiate
radio frequency energy and, if not installed
product.
Shock HazardS, Do Not
shall not be
Refer
Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation! This
?
This PRODUCT To Rain
vases, shall
This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC
?
Warning
To Prevent Fire
to
For U.S.A
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
or more
instructions in the literature
accompanying
Notices
?
or
as
shock,do not open the cabinet.
qualified personnel only.
equipment and receiver.
Connect the equipment into
outlet on a
circuit different from that to which the
receiver is connected.
Consult the dealer or an
technician for help.
This Class A
an
experienced radio/TV
digital apparatus
meets all
requirements of the Canadian InterferenceCausing Equipment Regulations.
methods shall be in accordance with the
National Electric
Code, ANSI/NFPA
70.
product is manufactured to comply with the radio interference
requirements of EEC DIRECTIVE 89/336/EEC, 93/68/EEC and
This
73/23/EEC.
Safetyprecautions..........................4
What'sinthebox...........................5
Construction.............................6-7
?Frontview...............................6
?Sideview................................6
?Rearview................................7
Installation...............................8-9
?Camerainstallation.......................8-9
Troubleshooting............................10
Dimension................................11
Specifications..........................12-13
3
Safety
Precautions
Do not attempt to
disassemble the camera
Avoid
camera
To prevent electric shock, do not
remove screws or covers. There are
Do not aim the
objects. Never
serviceable parts inside. Contact
qualified service personnel for repair.
Do not use
solvents or
sunlight
camera at
bright
strong
detergents
Handle the
with care
Use a dry cloth to clean the camera
when it is dirty. If it is hard to remove
dirt
to direct
the
point it toward direct
sunlight or other extremely bright
objects. Otherwise blooming or smear
distorting the image may result.
no
user
a
exposing
Do not abuse the
the camera, use a mild
detergent and wipe gently.
on
Do not expose the
to rain or moisture
requirements.
This
F
camera.
Avoid
striking, shaking, etc. The camera can
be damaged by improper handling or
storage.
Before operating, please
check temperature,
humidity and power source
Only use the camera when
temperature is between 14
(-10 C 50 C ).
camera
122 F
camera
product is designed for indoor
location where it is
protected from rain and moisture.
If exposed to moisture, turn the power
off immediately. Seek repair from
~
use or
~
Do not expose the camera
to conditions listed below.
in
a
qualified service personnel. Moisture
can damage the camera and also
create a danger of electric shock.
Do not operate in a room or area filled
with cigarette smoke, dust, or gas.
4
What's in the box
Video Cable
Tapping Screws
(2EA)
(Pan Lock Screw)
M4
Camera
Body
60 ft cable
(RJ11: LVC-D10NE/NC
RJ45: LVC-D100NM/NP)
5
Construction
Front View
LG logo
Tilt Base
Focus Lock Screw
Side View
Dome Cover
Lens
Tilting Lock Screw
Dome Cover
Separatory
Spring
6
8
6
pin Modular Jack: LVC-D10NE/NC
pin Modular Jack: LVC-D100NM/NP
Construction
Rear View
Base
Pin
RJ
Fixing Hole
Description
11(6 pin): LVC-D10NE/NC
RJ 45
(8 pin): LVC-D100NM/NP
1
NC
1
NC
2
VIDEO OUT
2
VIDEO OUT
3
GND
3
GND
4N C
4N C
5
NC
5
NC
6
12V DC
6
12V DC
7N C
8N C
7
Installation
Camera Installation
1.
Aim the LG logo of the Dome Camera to face the
you wish to watch.
2.
Tighten the M4 Tapping Screws to fix the Dome Camera on
the ceiling, then adjust the Pan (Left / Right) by moving the
Pan Base. Tighten the M4 Tapping Screws after adjustment.
Loosen the Tilting Lock Screw. Adjust the Tilt (Up / Down) by
moving the Tilt Base then tighten Tilting Lock Screw.
Loosen the Focus Lock Screw. Adjust the Focus by moving
the Focus Lens then tighten Focus Lock Screw.
Install the Dome Cover to the main body by turning it coun-
3.
4.
5.
place
that
terclockwise to the end.
Pan Base
Hole for
Fixing
Tilting Lock Screw
Tilt Base
M4
Tapping Screw
Focus Lock Screw
Dome Cover
8
Installation
NOTE
?
When you disassemble the Dome Cover, lift the Dome Cover
Separatory Spring on the opposite side of LG Logo and turn
the Dome Cover clockwise simultaneously.
Dome Cover
Separatory Spring
?
?
When you install the camera, handle with care. The camera
could be damaged by improper handling or storage.
If this camera is mounted on the other places except ceiling,
you need an extra bracket for mounting. (not supplied)
9
Check the following guide for the
before contacting service.
?
The
?
Contrast of the
possible
cause
of
a
problem
is poor
Does the Dome Cover have lots of dust on the surface?
Use a dry cloth to clean the camera when it is dirty.
Smear may be caused to the screen of night than daytime.
Adjust the Focus by moving the Focus Lens.
picture
screen
is not clear.
Check the condition of the monitor.
Alight source such as a spot light causes burn-in on the
display screen. Adjust position or angle of the camera to
eliminate strong background light.
10
90
2.75 inch
0.78 inch
99
72
11
Specifications (1)
Model
LVC-D10NE
EIA
CCIR
270K/250K
320K/290K
Signal System
Total / Effective Pixels
1/3-Inch B/W CCD
Pick-Up Device
Lens
(Super HAD)
Fixed Lens (f=3.7mm/F=2.0)
Gamma
0.45
2
Scanning System
:
59.94
Scanning Frequency
Resolution
Hz(VD)
More than 48dB
Standard Illuminance
2000Lux
0.2 Lux
Sensitivity
Output Signal
(H)
(AGC Off)
(3200 K)
(50 IRE, F2.0)
1Vp-p (75Ω)
Auto Iris
Electronic Shutter
(1/60
Electronic Shutter
1/10000)
(1/50
~
White Balance
1/10000)
~
Auto
12V DC UL Listed class 2 Power
Power Source
Supply Only.
2.3 W
Consumption
Operating Temp.
14 F
Storage Temp.
-4 F
Dimensions
122 F
(-10 C
140 F
(-20 C
~
~
3.9( 99)
X
50 C) (Humidity :0%RH
~
60 C) (Humidity :0%RH
~
2.75(70mm)
0.31 lb
Weight
Design and specifications
50Hz(VD)
More than 380 Line
S/N Ratio
Power
1 Interlace
Internal
Sync. System
Video
LVC-D10NC
are
subject
to
X
85%RH)
~
3.54( 90) inches
(141 g)
change without notice.
12
60%RH)
~
Specifications (2)
Model
LVC-D100NM
NTSC
PAL
270K/250K
320K/290K
Signal System
Total / Effective Pixels
Pick-Up Device
LVC-D100NP
1/3-Inch Interline Color CCD
(Super HAD)
Fixed Lens (f=3.7mm/F=2.0)
Lens
Angular Field of View(D)
92
Focus
Manual
Signal Process
Scanning System
Sync. System
Scanning Frequency
Digital Signal Process
2
:
1 Interlace
Internal
59.94
Resolution
330
Hz(VD)
Line (H)
S/N Ratio
More than 48dB
Standard Illuminance
2000Lux
(3200 K)
1.5 Lux (50 IRE, F2.0)
1Vp-p Composite (75Ω)
Sensitivity
Video Output Signal
Gain Control
Shutter
Auto
Speed
Electronic Shutter
Electronic Shutter
(1/60~1/10000)
(1/50~1/10000)
White Balance
Auto
Power Source
12V DC UL Listed class 2 Power
Power
Consumption
Operating Temp.
Storage Temp.
Supply Only.
2.3W
14 F
Weight
are
122 F
(-10 C 50 C) (Humidity :0%RH 60%RH)
140 F (-20 C 60 C) (Humidity :0%RH
85%RH)
3.9( 99) X 2.75(70mm) X 3.54( 90) inches
0.31 lb (141 g)
~
-4 F
Dimensions
Design and specifications
50Hz(VD)
320 Line (H)
~
~
subject
~
to
change without notice.
13
~
~
P/NO: 3834RS0072T
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising