LG | GR-N309LQA | LG GR-N309LQA Owner’s Manual

OWNER’S MANUAL
FRIDGEFREEZER
Please read this owner’s manual thoroughly before
operating and keep it handy for reference at all times.
GR - N309LQA
P/No. : 3828JD8636U
www.lg.com
Table of Contents
Introduction
Operation
Suggestion On
Registration
4
Important Safety Instruction
4
Identification of Parts
9
Temperature Control
10
Super Freezer
12
Self Test
12
Door Alarm
12
Miracle Zone
13
Ice Making
14
Defrosting
14
Storing Food
15
General Information
16
Lamp Replacement
17
To Reverse the Doors
17
Cleaning
18
Trouble Shooting
19
Food storage
Care and
Maintenance
Trouble Shooting
* Refer to Installation Insturction for details.
3
Introduction
Registration
The model and serial number are found on the rear of
this unit. This number is unique to this unit and not
available to others. You should record requested
information here and retain this guide as a permanent
record of your purchase. Staple your receipt here.
Introduction
Date of Purchase :
Dealer Purchased From :
Dealer Address :
Dealer Phone No. :
Model No. :
Serial No. :
Important Safety Instruction
To avoid any risk of personal injury, material
damage or incorrect use of the appliance, be sure to
observe the following safety precautions. (After
reading these owner’s instructions, please keep
them in a safe place for reference). Remember to
hand them over to any subsequent owner.
WARNING
4
Indicates that a
danger of death
or serious injury
exists
CAUTION
Indicates that a
risk of personal
injury or
material
damage exists
Introduction
Important Safety Instruction
WARNING
• This fridge-freezer must be properly installed and
located in accordance with the Installation Instruction
before it is used.
Precaution
• Before you install this fridge-freezer reference to
installation manual.
• Never unplug your fridge-freezer by pulling on the
power cord. Always grip plug firmly and pull straight
out from the outlet.
• When moving your appliance away from the wall, be
careful not to roll over or damage the power cord.
• After your fridge-freezer is in operation, do not touch
the cold surfaces in the freezer compartment,
particularly when hands are damp or wet. Skin may
adhere to these extremely cold surfaces.
• Pull out the power plug prior to cleaning the fridgefreezer.
Never damage, serverely bend, pull out, or twist the
power cord because power cord damage may cause a
fire or electronic shock.
Never place glass products in the freezer because they
may be broken when their inner contents are frozen.
• Do not directly spray water inside or outside the
fridge/freezer.
There is a risk of explosion or fire.
• Do not insert the power plug with wet hands.
You may receive an electric shock.
• Do not install the fridge/freezer in a damp place, where
it could be splashed with water.
Incorrect insulation of the electrical parts may cause an
electric shock or fire.
5
Introduction
Important Safety Instruction
• Do not disassemble, repair or alter the appliance.
It may cause fire or abnormal operations, which may
lead to injury.
• Pull the power plug out of the socket before replacing
the interior light in the refrigerator.
Otherwise, there is a risk of electric shock.
• If possible, connect the fridge-freezer to its own
individual electrical outlet to prevent it and other
appliances or household lights from causing an overload.
Do not modify or
extend the Power
Cord length.
It will cause electric shock or fire.
Accessibility of
Supply Plug
The supply plug of the refrigeratorfreezer should be placed in easy accessible position for
quick disconnection in emergency.
Supply Cord
Replacement
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
Danger
Risk of child entrapment.
Before you throw away your old refrigerator or freezer:
Take off the doors.
Leave the shelves in place so that children may not easily
climb inside.
Don't store
Don't store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
Grounding
(Earthing)
In the event of an electric short circuit, grounding
(earthing) reduces the risk of electric shock by providing
an escape wire for the electric current. In order to prevent
possible electric shock, this appliance must be grounded.
Improper use of the grounding plug can result in an
electric shock. Consult a qualified electrician or service
person if the grounding instructions are not completely
understood, or if you have doubts on whether the
appliance is properly grounded or not.
6
Introduction
Important Safety Instruction
WARNING
Keep ventilation openings, in the appliance enclosure
or in the built-in structure, clear of obstruction.
Do not use mechanical devices or other means to
accelerate the defrosting process, other than those
recommended by the manufacturer.
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food
storage compartments of the appliance, unless they
are of the type recommended by the manufacturer.
The refrigerant and insulation blowing gas used in the
appliance require special disposal procedures. When
disposal, please consult with service agent or
similarly qualified person.
This appliance contains a small amount of isobutane
refrigerant (R600a), natural gas with high
environmental compatibility, but it is also
combustible. When transporting and installing the
appliance, care should be taken to ensure that no
parts of the refrigerating circuit are damaged.
Refrigerant squirting out of the pipes could ignite or
cause an eye injury. If a leak is detected, avoid any
naked flames or potential sources of ignition and air
the room in which the appliance is standing for
several minutes.
In order to avoid the creation of a flammable gas air
mixture if a leak in the refrigerating circuit occurs, the size
of the room in which the appliance may be sited depends
on the amount of refrigerant used. The room must be
1m2 in size for every 8g of R600a refrigerant inside the
appliance. The amount of refrigerant in your particular
appliance is shown on the identification plate inside the
appliance.
Never start up an appliance showing any signs of
damage. If in doubt, consult your dealer.
7
Introduction
Important Safety Instruction
CAUTION
• If the wall socket is loose, do not insert the power
plug.
It may cause electric shock or fire.
• Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull it
straight out from the outlet.
You may disconnect a wire and cause a short circuit.
• Do not use a wet or damp cloth when cleaning the
plug. Remove any foreign matter from the power
plug pins.
Otherwise, there is a risk of fire.
• Do not put your hands into the bottom area of the
appliance.
Any Sharp edges may cause personal injury.
• After unplugging the appliance, wait for at least
five minutes before plugging it again to the wall
socket.
Abnormal operation of the freezer may cause material
damage.
• If the appliance is not to be used for a long time,
pull out the power plug.
Any deterioration in the insulation may cause fire.
• Do not let children touch or play with the control
panel on the front of the appliance.
• The refrigerant used in fridge/freezer and the
gases in the insulation material require special
disposal procedures. Ensure that none of the pipes
on the back of the appliances are damaged prior
to disposal.
8
Introduction
Identification of Parts
9
Operation
Temperature Control
Your fridge-freezer has controls that lets you regulate the
temperature in the fridge and freezer compartments.
Display Panel For
Temperature Control
Adjusting the
temperatures and
functions
10
Operation
• If you push button more than 3
seconds you can switch on or off
the Refrigerator.
Power
How to adjust the
temperature in the
refrigerator and
freezer
compartment
• The initial Temperature of the Freezer and Refrigerator
Compartment is -18°C and 2°C respectively.
You can now adjust the temperature of the
compartments as you want.
• When you press the
temperature control button,
the temperature of the
Freezer or Refrigerator part is
change by 1 degree.
Note
The actual inner temperature varies depending on the
food status, as the indicated setting temperature is a
target temperature, not actual temperature within
refrigerator.
Refrigeration function is weak in the initial time. Please
adjust temperature as above after using refrigerator for
minimum 2~3 days.
11
Operation
• Please select this function for prompt freezer.
Super Feezer
• This function is used when you want to freeze the
foods quickly. Press the SUPER FRZ (Super Freezer)
button once, and then the quick freeze operation starts
with the lamp it.
• The Super Freeze operation takes about 3 hours. When
its operation ends, it automatically returns to the
previous temperature setting. If you want to stop the
quick freeze operation, press the SUPER FRZ button
once more, the lamp goes out, and the Super Freeze
operation stops and the refrigerator returns to the
previous temperature setting.
In selecting
"On"
In selecting
"Off"
This function allows you to check for operational
problems. If you think you have a problem with your
fridge-freezer, then press the temperature control button:
- If the indicate lights move up or down, then there is no
problem with your fridge-freezer.
- If the indicate lights do not move up or down, then
please leave the power connected and call your nearest
service agent.
Self Test
When the door of the fridge is left open for a while, the
alarm sounds.
Door Alarm
12
Operation
• By pressing the button, store vegetables, fruits (at
relatively low conservation temperature) or other types
of food such as meat to be defrosted, raw fish, etc.
Miracle Zone
Temperature
Transition Corner
Method to Use
• You can select optimum temperature range depending
on types of food stored.
• 3 steps of temperature selection including 2°C, -1°C,
-3°C is available.
Vegetables/fruits and cold storage foods requiring
humidity maintenance and meats/fishes can be more
freshly stored depending on type of food stored.
13
Operation
• Fill water in ice making box of
the ice making corner. If water
is fully filled the ice will not be
separated well and water can be
dropped to make ice lumped.
• Ice will be dropped into the ice
storage bin by rotating ice
separation handle of ice making
compartment.
Ice Making
Note
• Rotating the ice separation handle before ice is fully
frozen may cause the remaining water drop into the
ice storage bin to lump the ice together.
Tip
To remove ice cubes easily, run water on the tray before
twisting.
• Defrosting takes place automatically.
• The defrosting water flows down to the evaporating
tray and is evaporated automatically.
Defrosting
14
Suggestions on food storage
Storing Food
CAUTION
• Do not store food which goes bad easily at low
temperature, such as banana, and melon.
• Allow hot food to cool prior to storing. Placing hot food
in the fridge-freezer could spoil other food, and lead to
higher electric bills.
• When storing the food, use a container with a lid. This
prevents moisture from evaporating, and helps food to
keep its taste and nutrients.
• Do not block air vents with food. Smooth circulation of
cold air keeps fridge-freezer temperature even.
• Do not open the door frequently. Opening the door lets
warm air enter the fridge-freezer, and cause
temperature to rise.
• Never keep too many foods in door rack, as this may
stop the door from fully closing.
• Do not store bottles in the freezer compartment,
Miracle Zone or snack bin they may break when frozen.
• Do not refreeze food that has been thawed. This causes
loss of taste and nutrition.
• Do not store pharmaceutical products, scientific materials
or other temperature sensitive products in the refrigerator.
Products that require strict temperature controls must
not be stored in the refrigerator.
• If you want to quick freeze new food, you put it middle
drawer of freezer compartment, and then press the
Super Freezer button.
• Do not put in front of the air hole of the upper drawer of
freezer compartment. It could decrease freezer capacity.
Note
If you keep the fridge-freezer in a hot, and humid place,
frequently open its door or put a lot of vegetables in it, dew
may form in it, which has no effect on its performance.
Remove the dew with dust cloth free from care.
15
Care and Maintenance
General Information
• 1~2 hour power failure does no harm to the foods
stores. Try to avoid opening and closing the door too
frequently.
Power Failure
• Take out foods from the fridge-freezer and firmly fix the
loose items with tape.
• Do not move the fridge freezer by sliding.
If You Move
• The Anti-Condensation pipe
is installed around the front
side of fridge-freezer as well
as on the partition between
fridge compartment and
freezer compartment to
prevent dewing.
Anti Condensation
Pipe
• Especially after installation or
when ambient temperature
is high, the fridge-freezer
may feel hot, which is quite normal.
16
Care and Maintenance
Lamp Replacement
1. Unplug the power cord
2.
3.
4.
from the outlet or
shutdown the main switch
in your house.
Remove the room lamp lid
by taking down while pulling its back projection.
Remove the lamp by turning it counterclockwise and
replace new one.
Assemble in reverse order of disassembly.
Replacement bulb must be the same specification as
original.
CAUTION
• You must check the O-RING, which is made by rubber
and prevent electric spark.
• Don’t touch the lamp, in case of light on the long
time. Because it can be very hot.
Note
• Lamp capacity is MAX 30W.
• The lamp will remain “ON” for 7minutes if the door is
left open and then it is “OFF” for safety. (If you
reopen the door, the lamp is “On”.)
• Your fridge-freezer is designed with reversible doors, do
that they may open from either the left of right hand
side to suit your kitchen design.
To Reverse the
Doors
However, When you want to reverse the doors, you
must be calling to service agent.
Reversing the doors is not covered by the warranty.
CAUTION
17
Care and Maintenance
Cleaning
Before Cleaning
Be sure to unplug the power or shutdown the main
switch in your house.
Exterior
Clean the outside of the fridge-freezer with a soft cloth
soaked with hot water or liquid detergent. If you use a
detergent, be sure to wipe it with a clean wet cloth.
Interior
As above.
After Cleaning
Check that the power cord is not damaged, power plug
has not overheated, and that the power plug is tightly
inserted into the outlet.
WARNING
Be sure to dry the appliance with a cloth after washing
it with water.
Do not use abrasive, petroleum, benzene, thinner,
hydrochloride acid, boiling water, rough brush, etc,
as they may damage parts of the fridge-freezer.
18
Trouble Shooting
Before calling for service, check this list.
It may save you both time and expense.
This list includes common occurrences that are not
the result of defective workmanship or materials in
this appliance.
Problem
Possible Causes
Fridge-Freezer
does not operate
• Power plug may be unplugged from the electric
outlet.
Plug it in securely.
• House fuse has blown or circuit breaker has
tripped.
Check and/or replace fuse and reset circuit breaker.
• Power cut.
Check house lights.
Fridge or Freezer
Compartment
Temperature too
warm
• Temperature control not set on proper position.
Refer to Temperature Control section.
• Appliance is placed close to heat source.
• Warm weather-frequent door openings.
• Door left open for a long time.
• Package holding door open or blocking air duct in
freezer compartment.
Vibration or
Rattling or
Abnormal Noise
• The floor on which the fridge-freezer is installed
may be uneven or the fridge-freezer may be
unstable.
Make it even by rotating the leveling screw.
• Unnecessary objects placed in the back side of the
fridge-freezer.
Frost or Ice
Crystals on frozen
Food
• Door may have been left ajar or package holding
door open.
• Too frequent or too long door openings.
• Frost within package is normal.
Moisture forms on
Cabinet Surface
• This phenomenon is likely to occur in a wet space.
Wipe it with a dry towel.
19
Trouble Shooting
Problem
Possible Causes
• Too frequent or too long door openings.
• In humid weather, air carries moisture into fridge when
doors are opened.
Moisture collects
inside
• Foods with strong odors should be tightly covered or
wrapped.
• Check for spoiled food.
• Interior needs cleaning.
Refer to CLEANING section
Fridge has odor
• Food package is keeping door open.
Move packages that keep door from closing.
• Fridge-freezer is not level.
Adjust the leveling screws.
• The floor on which the fridge-freezer is installed may
be uneven or the fridge-freezer may be unstable.
Slightly raise the front side with the leveling screw.
Door not closing
properly
• No power at outlet.
• Light lamp needs replacing.
Refer to the Lamp Replacement section
Interior light does
not work
20
Memo
21
Memo
22
Memo
23
LG Twin Tower, 20, Yoido-Dong, Youngdungpo-Gu, Seoul, 150-721, Korea.
Printed in Korea
Model:
GR-N309LQA
Built-in Refrigerator
Installation Manual
2
Contents
1. Caution Before Installation ......................................................... 3
2. Installation Parts......................................................................... 4
3. Block Diagram and Assembly ................................................... 5
4. Dimensions of Refrigerator and Cabinet ..................................... 6
5. Installation Environment for Built-in Refrigerator ........................ 7
6. Order of Installation
1) Preparation Work Before Installation of Refrigerator................... 8
2) Case-related Work After Inserting Refrigerator ......................... 10
3) Work Related with Integrated Door Panel ................................. 13
4) Work Related with the refrigerator freezer ................................ 14
5) Work Related with the refrigerator fridge................................... 16
6) Installation Check and Finishing Work ...................................... 18
7) Change of Door Open Direction of Refrigerator ........................ 19
Perform work after checking following contents:
This installation manual was prepared on the door to be opened to the right side. To change
the swing of the door to the left side, install product after firstly reading the last page (p. 19).
3
1. Caution Before Installation
CAUTION
■ Product must be installed in a location away from heat sources such as heaters and
hot-water systems. Must also be installed in a location away from direct sunlight.
Installation location must have adequate ventilation.
■ Prepare cabinetwork in accordance with the instructions to assure adequate
ventilation. Be sure that the installation has unobstructed air flow into front air vent.
If ventilation is not adequate the normal performance of the product may be
impaired or prohibited.
■ Install the product in such a way to prevent the ingress of rodents and vermin as
damage caused by them may result in fire.
■ Install the cabinet door to the refrigerator in such a way to maintain a 5mm gap
between the edge of the cabinet door and any adjacent wall.
■ Use the specified dimensions for the Integrated door panels. Oversized integrated
door panels may sag or cause interference with the correct operation of the
product.
■ Check there is no lean on the product door after attaching the Integrated door
panels. Check to see that the gasket of the fridge/freezer is properly attached.
■ Use Integrated panel material of sufficient strength to maintain integrity of support
screw/bolts under the weight of the panels. i.e. don't use material that will allow the
screws to be pulled out easily from the weight of the panels.
■ Use Cabinet material that is sealed and won't warp or twist from the heat generated
by the product or from the moisture produced by opening and closing the
refrigerator doors.
■ Make sure surrounding cabinet work is square (within 1mm of horizontal or
vertical). Make sure the base plate that the product is placed on is of sufficient
strength to not bow or warp under constant weight of the product. Bowing or
warping may result in the product not being square with surrounding cabinet work
causing interference with the opening and/or operation of the product.
■ Installation or removal of this product will require the cooperation of two persons.
■ For safety reasons keep children away from the installation location and all
installation materials during installation.
■ Be sure to keep the installation location neat and tidy, keep screws in a single
location and take them only as needed to prevent injury from screws laying around.
■ Do not connect product via an extension cord or multi adapter due to risk of fire.
■ Test run product prior to installation to assure its correct operation.
4
2. Installation Parts
Parts prepared
before installing
cabinet case
① Top cover
② Hinge stand
1 unit
4 units
⑤ Hinge cover
Parts related with
case after
inserting product
into cabinet case
1 unit
Parts related with ⑬Bottom part gasket
finishing work
④ Depth adjust Bracket
(hole size = 8mm)
4 units
⑥ Bracket case cover
1 unit
Parts related with
⑨ Paper jig
integrated
cabinet doors
after inserting
product into
cabinet case
1 unit
③ Depth adjust Bracket
(hole size = 5.5mm)
4 units
⑦ Bracket case
⑧ Case cover
1 unit
1 unit
⑩ Top bracket
1 unit
⑪ Depth adjust bracket cover ⑫ Top bracket cover
4 units
⑭ Cap screw
1 unit
⑮ Hinge front cover ⒃ Air path cover
⒔ Gasket
6 units
1 unit
ⓐ Wood bolting screw
1 unit
4 units
2 units
ⓑ Wood bolting screw
ⓒUpper bracket bolting screw
2 units
ⓓ Height adjusting nut
Spec
Quantity
Spec
Quantity
Spec
Quantity
Spec
Quantity
D4×L16
8
D4×L12
21
D4×6.5
8
M5
8
ⓔ Hinge bolting screw
ⓕ Horizontal adjusting leg bolting screw
ⓖ Spanner
Spec
Quantity
Spec
Quantity
Spec
Quantity
M5
10
D4×L14
1
-
1
Cross (+) driver
These tools are
required but
not supplied
2m tape rule
5
3. Block Diagram and Assembly
1
8
2
5
12
4
10
4
17
17
2
14
3
3
11
11
17
12
2
4
14
4
14
7
6
10
16
3
3
11
11
6
4. Dimensions of Refrigerator and Cabinet
※ The overall thickness of this figure is based on
15mm.
min
min
50m
mm
m
400
※ The dimension of cabinet must
correspond to that of figure.
min
600
m
mm in 50mm
400
mm
min
mm
580
1775mm
1017mm
54.5mm
5mm
617mm
696mm
39mm
554
mm
m
0m
/56
545
min
min
50m
mm
m
400
51mm
404
mm
CAUTION
The dimension of Integrated door panels changes if there is a change of cabinet material
thickness.
Thickness of Cabinet Case
Dimension of Integrated Door Panel (Freezer)
18mm
699mm
20mm
701mm
- Both the main body of the cabinet and the integrated door panel must be separated.
- The integrated door panel may sag if it is larger than the specified size.
- Install the product in such a way that all cabinet work is level both horizontally and vertically.
7
5. Installation Environment for Built-in
Refrigerator
■ Construct the cabinet work in accordance with these dimensions to guarantee adequate
ventilation for reliable heat exchange for product.
1. There must be unobstructed pathways
for air circulation to enter through
bottom inlet and escape through upper
outlet.
2. Ensure that No. ② path can be obtained
in in the cases where the No. ① path
cannot be used.
3. Ensure that the surface area of the inlet
and outlet ports for the No. ①, ② air
paths are more than 200cm2.
CAUTION
Required conditions for base of cabinet.
- Bottom surface:
It is required to use T 20mm to obtain strength.
- Space stand:
Ensure that the base is reinforced to the extent
that it can support up to 200KG (Product +
Food + Integrated Cabinet Doors + Shock of
opening and closing doors)
■Plan drawing of installation cabinet and
maximum opening of door
The base must be level to assure the uniform
downward pressure and distribution of weight
to alleviate warping of the base. Warping may
hinder the operation of the products doors.
580
- Level:
8
6. Order of Installation
1) Preparation Work Before Installation of Refrigerator
1. Installation of refrigerator top cover ①.
1). Pre-fold the top cover ① of refrigerator,
refer to the drawing to the right.
1
45mm
2). Fix the refrigerator top cover ① with the
wood bolting screw ⓑ (3 places) at a
point 45mm in from interior edge of
cabinet at each end and also in the
middle.
(The thickness of the cabinet material
determines the way the top cover ① is
cut. Please take notice of the below
"reference" for the correct cutting of the
top cover.)
45mm
1
b
45mm
※ Reference
AB
CD
1
In case of door opening to the right
Cut the A-spot when thickness of the
cabinet material is 18mm, cut the B-Spot
if it is 20mm.
In case of door opening to the left
Cut the D-spot when thickness of the
cabinet material is 18mm, cut the C-spot if
it is 20mm.
9
6. Order of Installation
1) Preparation Work Before Installation of Refrigerator
3) Assembly bracket
(Fig. 1)
② Tighten the screw
① Tilt to back
4) Assembly cover
(Fig. 2)
Tighten the screw
firmly.
After separating the double
sided tape, tighten the
screw firmly.
10
6. Order of Installation
1) Preparation Work Before Installation of Refrigerator
2. Insert the hinge stand ② into the hinge (4places) as in the below figure (See figure 3)
(Don’t insert the hinge stand when thickness of the cabinet material is 20mm.)
3. Lean the refrigerator backward and then fix the depth adjust bracket ③to the underside
(2places) loosely with the hinge bolting screw ⓔ in figure (Same for door work of the
cold store room and the freezing room) (See Fig.3).
(Fig. 3)
2
2
3
e
3
2
e
2
e
3
e
3
2) Case-related Work After Inserting Refrigerator
4. Draw the power cable through the back of the cabinet.
Be careful that the power cord is not trapped beneath
the refrigerator as you install it into the cabinet. The cord
may be crushed and damaged resulting in a fire hazard.
5. Insert the refrigerator into the cabinet so that the
end of the hinge stand ② corresponds to the front
part of the cabinet.
Caution must be taken not to jam your hands between
refrigerator and cabinet when inserting refrigerator into
cabinet.
Top Surface of Refrigerator
(Plan Drawing)
11
6. Order of Installation
2) Cabinet-related Work After Inserting Refrigerator
6. Adjust both verticality and horizontality by turning the horizontal adjusting leg (
of refrigerator.
)
1⃞ When the unit tilts backwards.
Adjust by turning the horizontal adjusting
leg anti-clockwise since the refrigerator
leans backward.
1⃞
2⃞ When the unit tilts forwards.
Adjust by turning the horizontal adjusting
leg clockwise since the refrigerator leans
forward.
2⃞
Check that the depth dimensions of the front part of the cabinet and the front part of
refrigerator door are constant by using the spannerⓖ (See Fig. 4).
(Fig. 4)
Front Part of Cabinet
Front Part of Refrigerator Door
4mm
Spanner
Front Part of
Cabinet
3.5mm
Front Part of
Refrigerator Door
3mm
ⓖ
g
Front Part of
Cabinet
Front Part of
Refrigerator Door
ⓖ
Sitting Part of
Cabinet
Sitting Part of
Refrigerator Door
12
6. Order of Installation
2) Case-related Work After Inserting Refrigerator
7. Check that the end of the hinge stand ②
corresponds to the right front side of the
cabinet.
8. Fix the hinge with the wood bolting
screw ⓐ (8places) (See Figure 5).
Be careful when working on hinges as you
may be injured by the hinge operation if the
door moves.
(Fig. 5)
a
9. Check that the left / right depth interval as in
Figure 6 is constant by using a ruler.
(Fig. 6)
13
6. Order of Installation
3) Work Related with Integrated Door Panel.
10. Place the paper jig ⑨ on the standard line (see reference) on the back of the integrated door
panel (See Fig. 7).
※ Reference For the door of the fridge: Place the paper jig ⑨ at the point away 912 mm
from the underside of the fridge integrated door panel.
(Fig. 7)
9
Standard Line
of Paper Jig
(For right hinge)
Standard Line
of Paper Jig
(For left hinge)
Standard Line
of Paper Jig
(For right hinge)
Standard Line
of Paper Jig
(For left hinge)
9
912mm
Integrated door panel of the fridge
11. Indicate two holes at the paper jig ⑨ on
the integrated door panel (See Figure 8).
Integrated door panel of the freezer
(Fig. 8)
⑨
Double check the indicated point is located
in an accurate position before fixing with the
wood bolting screw ⓑ.
12. After removing the paper jig ⑨ , fix the top bracket ⑩ of the integrated door panel
by using the wood bolting screw ⓑ (4 places) with the top two holes lined up to
the marked spots (from the paper jig) on the integrated door panel. (See Figure 9).
(Fig. 9)
10
10
b
b
b
b
Integrated door panel of the fridge
Integrated door panel of the freezer
14
6. Order of Installation
4) Work Related with the Freezer Door
13. Hang the top bracket ⑩ of the integrated door panel on the height adjusting screw of the
door top part after inserting the height adjusting nut ⓓ(2 places) on to the height
adjusting screw. Loosely tighten the height adjust nut ⓓ (2 places) (See Figure 10).
Perform work with care since you may be injured or the integrated door panel of the freezer is
damaged because the hole is unmatched when installing the integrated door panel of the freezer.
d
10
d
(Fig. 10)
Height Adjust Screw
14. Move the integrated door panel to the left or right and adjust the left/right interval
uniformly after checking the integrated door panel and the door of the freezer are
parallel (Move position of the height adjust nut ⓓ for adjustment up or down
when they are not parallel) (See Figure 11)
g
d
Forward/
Backward
Top/Down
Adjust
Left/Right
(Fig. 11)
Front Part
of Cabinet
15. Check the dimension by using the
spanner ⓖ (See Figure 12).
Parallel
4mm
Integrated door
Spanner
4mm
g
16. Start work from step No. 13 again after
releasing the height adjust nut ⓓ
where the dimension is not matched.
Parallel
(Fig. 12)
15
6. Order of Installation
4) Work Related with the Freezer Door
17. After positioning the depth adjust bracket ④ as in Figure 13, fix it with the hinge
adjust screw ⓔ(2 places) and then fix it with the top bracket bolting screw ⓒ
(4 places) (See Figure 13).
e
4
c
(Fig. 13)
18. After inserting the wood bolting screw ⓑ (4 places) into the depth adjust bracket
③, move the integrated door panel to the depth direction and adjust the interval to
4mm (see Figure 12). (See Figure 14).
depth interval
b
3
(Fig. 14)
19. Install the top bracket cover ⑫ of the integrated door panel on the top side of the
freezer door, and install the depth adjust bracket cover ⑪ on the underside of the
freezer(See Figure 15).
Topside of the
Freezer door
Underside of the
Freezer door
(Fig. 15)
⑫
11
16
6. Order of Installation
5) Work Related with the Fridge Door
20. After inserting the height adjust nut ⓓ (2 places) into the height adjust screw, hang the
top bracket ⑩ of the integrated door panel on the height adjust screw on the top part of
the refrigerator door.Loosely tighten the height adjust nut ⓓ (2 places) (See Figure 16).
Perform work with care since
you may be injured or the
integrated door panel of the
fridge is damaged because the
hole is unmatched when
installing the integrated door
panel of the fridge.
d
(Fig. 16)
10
d
Height Adjust Screw
21. Move the integrated door panel to the left or right and adjust the left/right interval
uniformly after checking the integrated door panel and the door of the fridge are parallel
(See Figure 17). (Move position of the height adjust nut ⓓ for adjustment up or down
when they are not parallel)
g
d
Forward/
Backward
Top/Down Adjust
Left/Right
(Fig. 17)
22. Adjust depth interval between the integrated door panel and the front part of the cabinet to
4mm. Adjust interval between the integrated door panel of the freezer and the integrated door
panel of the fridge to 5mm. Securely tighten the loose height adjust nut ⓓ after adjustment.
23. Check the size by using the spanner ⓖ (See Figure 18). Specially, check the interference
between the fridge door and the freezer door(or freezer hinge).
(Fig. 18)
Parallel
Furniture Door
of the fridge
g
Parallel
Furniture Door
of the Freezer
5mm
4mm
24. Start work from Step No. 22 again after releasing the ⓓ height adjust nut where the size
is not matched. And adjust height of the fridge door with ⓓ when interference occurs
between the fridge door and the freezer door(or freezer hinge)
17
6. Order of Installation
5) Work Related with the Fridge Door
25. After positioning the depth adjust bracket ④ as in Figure 19, fix it with the hinge
bolting screw ⓔ (2 places) and then fix it with the top bracket bolting screw ⓒ
(4 places) (See Figure 19).
e
(Fig. 19)
4
c
26. After bolting the wood bolting screw ⓑ (4 places) to the height adjust bracket ③, move the
integrated door panel to the depth direction and adjust the interval to 4mm (see Figure 12).
(See Figure 20).
depth interval
b
3
(Fig. 20)
27. Install the top bracket cover ⑫ on the top side of the fridge, and cover the depth adjust
bracket cover ⑪ on the underside of the fridge(See Figure 21).
Topside of the
Fridge Door
Underside of the
Fridge Door
(Fig. 21)
⑫
11
18
6. Order of Installation
6) Installation Check and Finishing Work
28. Insert the hinge front cover ⑮ into the front part inside the hinge (4places).
29. Insert the air path cover ⒃ into the square cloth support.
30. After cutting the gasket ⒔ to
A
suit the interval, attach it as in
Figure 22, use the gasket on
the hinge side, the gasket on
B
the opposite side of hinge.
1676mm
31. Insert the cap screws ⑭ as in
Figure 22 (6 places).
1800mm
(Fig. 22)
17
Ref Side of
rige
rato
r
14
17
15
17
15
14
17
14
14
6
6
15
16
After securing screws,
cover the cap screw.
13
19
6. Order of Installation
7) Change of Door Open Direction of Refrigerator
※ Perform work for changing the door before installation.
1. Loosely release the screws ❶,
❸ of the hinge on the case part
of the freezer and then
separate the door by pushing it
to the right (See Figure 23).
2. Release the screws No. ❶, ❸
completely and then fix them
loosely to the reverse side (See
Figure 24)
3. Separate the hinge by releasing
the No. ❷, ❹ bolt to the door.
(Fig. 23)
4. Move the separated hinges
(Figure 24) diagonally and fix it
to the door by turning the
hinge by 180˚.
5. Push the hinge from the left
side to the right side to ensure
that the door hinge and the
screws are fixed to the case
match.
6. Adjust the top/down or the
left/right interval of the
refrigerator door so that
leaning should not occur to
either side, and then tighten
screws.
7. If the hinge bolting is
completed, insert the ⑭ cap
screws at the opposite side of
the hinge (6 places).
(Fig. 24)
※ Same as above order for change of the door open direction of the fridge door.
P/No.: 3828JD8684P
Download PDF