LG | GR-N254BLQ | LG GR-N254BLQ Owner’s Manual

OWNER’S MANUAL
FREEZER
Please read this owner’s manual thoroughly before
operating and keep it handy for reference at all times.
GR - N254BLQ
P/No. : MFL62525414
www.lg.com
Table of Contents
Introduction
Operation
Suggestion On
Food storage
Care and
Maintenance
Trouble Shooting
Product Information
Registration
4
Important Safety Instruction
4
Identification of Parts
18
Temperature Control
19
Display Panel For Temperature Control
19
Power
20
How to adjust the temperature
in the freezer compartment
20
Super Freezer
21
Self Test
21
Door Alarm
21
Ice Making
22
Defrosting
22
About Ice
23
How to store food properly
23
Storing Food
24
General Information
25
How to disassemble each component
26
Cleaning
27
Trouble Shooting
28
Product Information
30
* Refer to Installation Insturction for details.
3
Introduction
Registration
The model and serial number are found on the rear of
this unit. This number is unique to this unit and not
available to others. You should record requested
information here and retain this guide as a permanent
record of your purchase. Staple your receipt here.
Introduction
Date of Purchase :
Dealer Purchased From :
Dealer Address :
Dealer Phone No. :
Model No. :
Serial No. :
Important Safety Instruction
BASIC SAFETY PRECAUTIONS
This guide contains many important safety messages.
Always read and obey all safety messages.
This is the safety alert symbol. It alerts you to safety
messages that inform you of hazards that can kill or hurt
you or others or cause damage to the product. All safety
messages will be preceded by the safety alert symbol and
the hazard signal word DANGER, WARNING, or
CAUTION. These words mean:
DANGER
You will be killed or seriously injured if
you don’t follow instructions.
WARNING You can be killed or seriously injured if
you don’t follow instructions.
CAUTION
Indicates an imminently hazardous
situation which, if not avoided, may
result in minor or moderate injury, or
product damage only.
All safety messages will identify the hazard, tell you how
to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
4
Introduction
Important Safety Instruction
WARNING
To reduce the risk of fire, electric shock, or injury to
persons when using your product, basic safety
precautions should be followed, including the
following. Read all instructions before using this
appliance.
1. When connecting the power
A dedicated outlet should be used.
• Using several devices at one outlet
may cause fire.
• If unit is connected to an earth
leakage breaker it may trip resulting
in spoiled food.
Do not allow the power plug to face upward or to
be crushed at the back of the fridge-freezer.
If the cord is crushed behind the
refrigerator it may damage the cable
resulting in fire. An upward facing plug
may pull loose under the weight of the
cord resulting in electrical failure
causing fire or the fridge turning off and spoiling food.
Prevent the power cord from being crushed or
kinked if the refrigerator is pushed in after the
power plug is extracted during the installation.
Crushed or kinked cables can become the cause of fire
or electric shock.
When moving your appliance away from the wall, be
careful not to roll over or damage the power cord.
Do not allow heavy objects to kink or crush the
power cord.
It may damage the power cord and
become a cause of fire or electric shock.
5
Introduction
Important Safety Instruction
Do not extend or modify the length of the power
plug.
This may become the cause of fire or
electric shock.
Unplug the power plug when cleaning, handling or
replacing the interior lamp of the fridge-freezer.
• It may cause electric shock or injury.
• When replacing the interior lamp of
the fridge-freezer, make sure that the
insulating rubber ring within the
socket is not taken off.
Do not pull out the cord or touch the power plug
with wet hands.
It may cause electric shock or injury.
Remove water or dust from the power plug and
insert it with the ends of the pins
securely connected.
Dust, water or unstable connection may
cause fire or electric shock.
Do not disconnect by pulling on the cord.
Always disconnect by grasping and
pulling on the plug top.
Pulling on the cable may damage the cable
resulting in electric shock or fire.
6
Introduction
Important Safety Instruction
Make sure of grounding.
Consult a qualified electrician or
service person if the grounding
instructions are not completely
understood, or if you have doubts
on whether the appliance is properly
grounded.
Incorrect grounding may lead to electric shock in the
event of a breakdown.
Always have unit grounded in accordance with
local regulations.
If incorrectly grounded it may become the cause of a fire.
Ground
Wire
Copper
Flat
When the power cord or the power plug is
damaged or the holes of the outlet
are loosed, do not use them.
It may cause electric shock or be the cause
of a fire.
Wait for 5 minutes or longer when
reconnecting the plug.
It may cause the operation of the
refrigerator to fail.
After
5minutes
2. When using the fridge-freezer
Do not place heavy objects or liquid filled objects
on the top of the refrigerator.
Heavy objects may fall when opening and
closing doors resulting in injury. Liquid
filled objects may leak or fall and break
resulting in injury, or electric shock.
Do not lean on or hang from the doors or shelves
of the refrigerator.
This may damage the doors or shelves
of the refrigerator or cause it to topple
over resulting in injury and damage.
Always supervise children when they
are near the refrigerator.
7
More than
30 inches
Introduction
Important Safety Instruction
Prevent children from entering the product.
It may endanger the life of a child if the
child enters the refrigerator.
Take care when opening and closing the
refrigerator doors. Vigorous opening or closing
may cause the contents to topple out resulting in
injury or damage.
Do not install the refrigerator in a damp or wet
environment.
Moisture may penetrate electrical
components resulting in fire or electric
shock.
Do not store or use Inflammable materials in or
around the refrigerator.
It may become the cause of an
explosion or fire.
Do not use or place heated or flame based scented
products (Such as scented candles
or incent burners) in the fridge to
deodorise.
It may become the cause of an
explosion or fire.
8
Introduction
Important Safety Instruction
Do not store medicine or academic materials in the
fridge-freezer.
If materials with strict temperature
restrictions, such as medicines, are
stored, they may deteriorate or react
undesirably resulting in possible harm
or risk.
Do not use any combustible spray near the fridgefreezer.
It may become the cause of an
explosion or fire.
Avoid any heating devices. Install in places away
from any flame. Such as fireplaces, heaters and
ovens. Pay particular attention to
avoid locating near gas related
products.
It may become the cause of an
explosion or fire.
Do not place flower vases, cups,
cosmetics, medicine or any container
with water on the fridge-freezer.
It may fall, leak or spill resulting in
possible electric shock or fire.
In case of a heavy electrical storm or if unit is not to
be used for a long period of time,
disconnect the power plug.
There is a possibility for electrical
damage. This may lead to an electric
shock or fire.
9
Introduction
Important Safety Instruction
DO NOT use a water damaged unit until it has been
certified safe by a licensed
electrician or similarly qualified
person.
It may be the cause of an electric shock
or fire.
When gas is leaked, do not touch the fridge/freezer
or the outlet and ventilate the room immediately.
• The explosion by spark may cause
fire or burn.
• Because this fridge/freezer uses
natural gas (isobutene, R600a) as
the environment-friendly
refrigerant, even a small amount (80~90g) is
combustible. When the gas is leaked by the severe
damage during delivering, installing or using the
fridge/freezer, any spark may cause fire or burn.
Do not spray water on either the inside or outside
of the refrigerator. Do not use alcohol or mineral
based cleaners on the refrigerator
(such as Benzene or Thinners).
These may deteriorate or penetrate the
insulation or electrical components
resulting in possible electric shock, fire
or damage to refrigerator.
When any strange smell or smoke is detected from
the fridge-freezer, disconnect the power plug
immediately and contact a service center.
Continuing to run unit may result in
Damage or fire.
Service
Center
10
Introduction
Important Safety Instruction
Do not allow any person except a qualified
engineer to disassemble, repair or alter the fridgefreezer.
It may cause injury, electric shock or
fire.
Do not use the fridge-freezer for non-domestic
puposes (storing medicine or testing material, or use
in a mobile application.)
It may cause an unexpected risk such
as fire, electric shock, deterioration of
stored material or chemical reaction.
When disposing the fridge-freezer, remove the
doors from the refrigerator.
Failure to do so may cause a child to
become trapped inside.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
11
Introduction
Important Safety Instruction
Install the fridge-freezer on a solid and level floor.
Installing it in an unstable place may
cause death by the refrigerator falling
down when opening or closing the door.
Do not insert hands or a metal object into the exit
of cool air, the cover, the bottom of the fridgefreezer, the heatproof grill (exhaust hole) at the
back.
It may cause an electric shock or
injury.
CAUTION
Violating this direction may cause injury or damage to
house or contents. Always be careful, please.
Do not touch food or containers in
the freezer with wet hands.
It may cause frostbite.
Ensure that all foods and containers are stored or
stacked in a stable manner.
The food may fall during opening and closing of the
door of the refrigerator and hurt people.
Do not put filled bottles in the
freezer.
It may freeze the contents and break the
bottle possibly resulting in injury.
12
Introduction
Important Safety Instruction
Do not insert hands into the bottom of the fridgefreezer.
The iron plate at the bottom may cause
injury.
Carry the fridge-freezer with the handles at the
bottom of the front and the top of the rear.
Otherwise, your hands may slip
possibly resulting in injury or product
damage. Because the product is heavy,
carrying it alone may hurt people or
accidents may occur.
Because opening or closing the door of the fridgefreezer may cause injury to other people around it,
be careful, please.
Opening both doors can result in
fingers or hands being crushed in the
small gap between the doors. Open
doors could result in children being
hurt by the corners of the doors
(particularly the freezer door as lower edge might be out
of line of site).
Do not put any living animal in the
fridge-freezer.
13
Introduction
Important Safety Instruction
WARNING
Precaution
14
•
This fridge-freezer must be properly installed and
located in accordance with the Installation Instruction
before it is used.
•
Before you install this fridge-freezer refer to installation
manual.
•
Never unplug your fridge-freezer by pulling on the
power cord. Always grip plug firmly and pull straight
out from the outlet.
•
After your fridge-freezer is in operation, do not touch
the cold surfaces in the freezer compartment,
particularly when hands are damp or wet. Skin may
adhere to these extremely cold surfaces.
•
Pull out the power plug prior to cleaning the fridgefreezer.
Never damage, serverely bend, pull out, or twist the
power cord because power cord damage may cause a
fire or electric shock.
Never place glass products in the freezer because they
may be broken when their inner contents are frozen.
•
Do not directly spray water inside or outside the
fridge/freezer.
There is a risk of explosion or fire.
•
Do not insert the power plug with wet hands.
You may receive an electric shock.
•
Do not install the fridge/freezer in a damp place, where
it could be splashed with water.
Water may penetrate electrical components causing a
risk of fire, electric shock or damage.
Introduction
Important Safety Instruction
•
•
•
Do not disassemble, repair or alter the appliance. It
may cause fire or abnormal operations, which may lead
to injury.
Pull the power plug out of the socket before replacing
the interior light in the refrigerator.
Otherwise, there is a risk of electric shock.
If possible, connect the fridge-freezer to its own
individual electrical outlet to prevent it and other
appliances or household lights from causing an overload.
It will cause electric shock or fire.
Do not modify or
extend the Power
Cord length
Accessibility of
Supply Plug
The supply plug of the refrigerator-freezer should be
placed in easy accessible position for quick disconnection
in emergency.
Supply Cord
Replacement
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
Danger
Risk of child entrapment.
Before you throw away your old refrigerator or freezer:
Take off the doors.
Leave the shelves in place so that children may not
easily climb inside.
Don't store
Don't store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
Grounding
(Earthing)
In the event of an electric short circuit, grounding
(earthing) reduces the risk of electric shock by providing
an escape wire for the electric current. In order to
prevent possible electric shock, this appliance must be
grounded. Improper use of the grounding plug can result
in an electric shock.
15
Introduction
Important Safety Instruction
WARNING
Keep ventilation openings, in the appliance
enclosure or in the built-in structure, clear of
obstruction.
Do not use mechanical devices or other means to
accelerate the defrosting process, other than those
recommended by the manufacturer.
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food
storage compartments of the appliance, unless they
are of the type recommended by the manufacturer.
The refrigerant and insulation blowing gas used in
the appliance require special disposal procedures.
When disposal, please consult with a service agent
or similarly qualified person.
This appliance contains a small amount of isobutane
refrigerant (R600a), natural gas with high
environmental compatibility, but it is also
combustible. When transporting and installing the
appliance, care should be taken to ensure that no
parts of the refrigerating circuit are damaged.
Refrigerant squirting out of the pipes could ignite
or cause an eye injury. If a leak is detected, avoid
any naked flames or potential sources of ignition
and air the room in which the appliance is standing
for several minutes.
In order to avoid the creation of a flammable gas air
mixture if a leak in the refrigerating circuit occurs, the
size of the room in which the appliance may be sited
depends on the amount of refrigerant used. The room
must be 1m2 in size for every 8g of R600a refrigerant
inside the appliance. The amount of refrigerant in your
particular appliance is shown on the identification plate
inside the appliance.
Never start up an appliance showing any signs of
damage. If in doubt, consult your dealer.
16
Introduction
Important Safety Instruction
CAUTION
17
•
If the wall socket is loose, do not insert the power
plug.
It may cause an electric shock or fire.
•
Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull it
straight out from the outlet.
You may disconnect a wire and cause a short circuit
that could cause an electric shock or fire.
•
Do not use a wet or damp cloth when cleaning the
plug. Remove any foreign matter from the power
plug pins.
Otherwise, there is a risk of fire.
•
Do not put your hands into the bottom area of
the appliance.
Any Sharp edges may cause personal injury.
•
After unplugging the appliance, wait for at least
five minutes before plugging it again to the wall
socket.
Abnormal operation of the freezer may cause material
damage.
•
If the appliance is not to be used for a long time,
pull out the power plug.
Any deterioration in the insulation may cause fire.
•
Do not let children touch or play with the control
panel on the front of the appliance.
•
The refrigerant used in a fridge/freezer and the
gases in the insulation material require special
disposal procedures. Ensure that none of the pipes
on the back of the appliances are damaged prior
to disposal.
Introduction
Identification of Parts
Freezer Shelf
Ice Tray & Bank
Freezer
Compartment
Leveling Screw
18
Operation
Temperature Control
Your freezer has controls that let you regulate the
temperature in the freezer compartments.
Display Panel For
Temperature Control
Adjusting the
temperatures and
functions
Display Panel
SUPER FRZ.
FRZ.TEMP.
Super Freezer
3SECS
Power
Temperature Adjustment Button
for Freezer Compartment
19
POWER
Operation
Power
•
If you push button more than 3 seconds
you can switch on or off the Freezer.
POWER
3SECS
How to adjust the
temperature in the
freezer
compartment
•
The initial Temperature of the Freezer Compartment is
-23°C and -15°C respectively.
You can now adjust the temperature of the
compartments as you want.
•
Note
When you press the temperature
control button, the temperature
of the Freezer part is change by
1 degree.
The actual inner temperature varies depending on the
food status, as the indicated setting temperature is a
target temperature, not actual temperature within
freezer.
Refrigeration function is weak in the initial time. Please
adjust temperature as above after using freezer for
minimum 2~3 days.
20
Operation
Super Feezer
•
•
•
Please select this function for prompt freezer.
This function is used when you want to freeze the
foods quickly. Press the SUPER FRZ (Super Freezer)
button once, and then the quick freeze operation starts
with the lamp it.
The Super Freeze operation takes about 3 hours. When
its operation ends, it automatically returns to the
previous temperature setting. If you want to stop the
quick freeze operation, press the SUPER FRZ button
once more, the lamp goes out, and the Super Freeze
operation stops and the freezer returns to the previous
temperature setting.
SUPER FRZ.
SUPER FRZ.
SUPER FRZ.
In selecting
"On"
In selecting
"Off"
This function allows you to check for operational
problems. If you think you have a problem with your
freezer, then press the temperature control button:
Self Test
- If the indicate lights move up or down, then there is no
problem with your freezer.
- If the indicate lights do not move up or down, then
please leave the power connected and call your nearest
service agent.
When the door of the freezer is left open for a while, the
alarm sounds.
Door Alarm
21
Operation
Ice Making
•
•
Fill water in ice making tray. Only fill
with enough water to maintain
individual blocks, if over filled blocks
will not separate properly and water
may spill into ice bin clumping ice
together.
Ice will be dropped into the ice
storage bin by rotating ice separation
handle of ice making compartment.
•
Note
Defrosting
•
•
22
Rotating the ice separation handle before ice is fully
frozen may cause the remaining water to drop into
the ice storage bin and clump ice together.
Defrosting takes place automatically.
The defrosting water flows down to the evaporating
tray and is evaporated automatically.
Suggestions on food storage
About Ice
1. Fill water up to the level line of
the ice-making tray.
- It is hard to remove ice if water
is full.
- When you want to freeze ice
quickly, select "Quick
freezing".
The level line
2. Twist the ice-making tray to
remove ice.
- Do not store the not
completely frozen ice.
- Do not bend the ice-making
tray. It may break.
- Do not make ice with the
ice-storing bin. It may break.
How to store food properly
Open the cover to take out food.
Freezer shelf
Place the frozen food such as meat, fish, frozen bun and
ice cream here.
Freezer basket
The ice-making tray and the ice-storing bin are here.
Ice-maker
23
Suggestions on food storage
Storing Food
CAUTION
•
•
•
•
•
•
•
•
•
•
•
Do not store food which goes bad easily at low
temperature, such as banana, and melon.
Allow hot food to cool prior to storing. Placing hot
food in the freezer could spoil other food, and lead to
higher electric bills.
When storing the food, use a container with a lid. This
prevents moisture from evaporating, and helps food to
keep its taste and nutrients.
Do not block air vents with food. Smooth circulation of
cold air keeps freezer temperature even.
Do not open the door frequently. Opening the door
lets warm air enter the freezer, and cause the
temperature to rise.
Never keep too many foods in door rack, as this may
stop the door from fully closing.
Do not store bottles in the freezer compartment,
Miracle Zone or snack bin they may break when frozen.
Do not refreeze food that has been thawed. This
causes loss of taste and nutrition.
Do not store pharmaceutical products, scientific
materials or other temperature sensitive products in the
freezer.
Products that require strict temperature controls must
not be stored in the freezer.
If you want to quick freeze new food, you put it middle
drawer of freezer compartment, and then press the
Super Freezer button.
Do not put in front of the air hole of the upper drawer
of freezer compartment. It could decrease freezer
capacity.
If you keep the freezer in a hot, and humid place, frequently
open its door or put a lot of vegetables in it, dew may form
in it, which has no effect on its performance. Remove the
dew with a lint free cloth.
Note
24
Care and Maintenance
General Information
Power Failure
•
1~2 hour power failure does no harm to the foods
stored. Try to avoid opening and closing the door too
frequently.
If You Move
•
Take out foods from the freezer and firmly fix the loose
shelves, draws and accessories with tape.
Do not move the freezer by sliding.
•
Anti Condensation
Pipe
•
•
25
The Anti-Condensation
pipe is installed around the
front side of freezer as well
as on the partition between
freezer compartment to
prevent dewing.
Especially after installation
or when ambient
temperature is high, the
freezer may feel hot, which
is quite normal.
Care and Maintenance
How to disassemble each
component
It can be possible to disassemble only when the door is
opened by 90° or wider. Disassembling should be done by
the reverse order of assembling.
Lift up the shelf cover, and then slightly lift
up and pull out the front of the shelf to
remove.
Upper shelf
1
3
2
Pull out the drawer, and then
slightly lift up and pull out
the front to remove.
Lower drawer
To Reverse the
Doors
•
CAUTION
2
1
Your freezer is designed with reversible doors, so that
they may open from either the left of right hand side
to suit your kitchen design.
However, When you want to reverse the doors, you
must contact a service agent.
Reversing the doors is not covered by the warranty.
26
Care and Maintenance
Cleaning
Be sure to unplug the power or shutdown the main
switch in your house.
Before Cleaning
Clean the outside of the freezer with a hot damp cloth
with or without cleaning detergent. If you use a
detergent, be sure to wipe it with a clean wet cloth.
Exterior
As above.
Interior
After Cleaning
Check that the power cord is not damaged, power plug
has not overheated, and that the power plug is tightly
inserted into the outlet.
WARNING
Be sure to dry the appliance with a cloth after washing
it with water.
Do not use abrasive, petroleum, benzene, thinner,
hydrochloride acid, boiling water, rough brush, etc,
as they may damage parts of the freezer.
27
Trouble Shooting
Before calling for service, check this list.
It may save you both time and expense.
This list includes common occurrences that are not
the result of defective workmanship or materials in
this appliance.
Possible Causes
Problem
Freezer does not
operate
•
•
•
Freezer
Compartment
Temperature too
warm
•
•
•
•
•
Vibration or
Rattling or
Abnormal Noise
•
•
Frost or Ice
Crystals on frozen
Food
•
•
•
Moisture forms on
Cabinet Surface
•
28
Power plug may be unplugged from the electric
outlet.
Plug it in securely.
House fuse has blown or circuit breaker has
tripped.
Check and/or replace fuse and reset circuit breaker.
Power cut.
Check other appliances in the house for operation.
Temperature control not set on proper position.
Refer to Temperature Control section.
Appliance is placed close to heat source.
Warm weather-frequent door openings.
Door left open for a long time.
Package holding door open or blocking air duct in
freezer compartment.
The floor on which the freezer is installed may be
uneven or the freezer may be unstable.
Level refrigerator by adjusting the leveling feet.
Objects fallen or stored behind refrigerator.
Door may have been left ajar or package holding
door open.
Door opened too frequently or for to long a
period.
Frost within package is normal.
This phenomenon is likely to occur when
installation location is in a high humidity or damp
environment.
Wipe it with a dry towel.
Trouble Shooting
Problem
Possible Causes
Moisture collects
inside
•
Freezer has odor
•
•
•
•
Door not closing
properly
•
•
•
Interior light does
not work
•
•
29
Door opened too frequently or for to long a period.
In humid weather, air carries moisture into freezer
when doors are opened.
Foods with strong odors should be tightly covered or
wrapped.
Check for spoiled food.
Interior needs cleaning.
Refer to CLEANING section.
Food package is keeping door open.
Move packages that stop door from closing.
Freezer is not level.
Adjust the leveling screws.
The floor on which the freezer is installed may be
uneven or the freezer may be unstable.
Adjust leveling feet to create a slight tilt backwards on
the refrigerator.
No power at outlet.
Light lamp needs replacing.
Refer to the Lamp Replacement section
Memo
30
Memo
31
LG Twin Tower, 20, Yoido-Dong, Youngdungpo-Gu, Seoul, 150-721, Korea.
Printed in Korea
Model:
GR-N281/254
Built-in Fridge/Freezer
Installation Manual
2
Contents
1. Note before installing................................................................. 3
2. Components to install ................................................................ 4
3. Assembly/Disassembly diagram of Built-in refrigerator ............... 5
4. Dimension of Built-in refrigerator and cabinet............................ 6
5. Installing the built-in refrigerator ................................................ 7
6. Procedure to install
1) Preparing before installing the refrigerator .................................. 8
2) Cabinet related work after inserting the refrigerator .................. 11
3) Integrated door panel related work ........................................... 13
4) Refrigerator door related work .................................................. 14
5) Installation checkup and finishing work .................................... 17
6) Changing the opening direction of the refrigerator door ........... 18
7) Integrated door panel gap ........................................................ 19
* The procedure and method of installation for the refrigerator are the
same for the freezer.
Read the following BEFORE proceeding with installation. :
This manuals descriptions are based on the door opening to the right.
If you want to open the door to the left, install after reading Page 18.
3
1. Note before installing
Caution
■ Product must be installed in a location away from heat sources such as heaters and
hot-water systems. Must also be installed in a location away from direct sunlight.
Installation location must have adequate ventilation.
■ Prepare cabinetwork in accordance with the instructions to assure adequate
ventilation. Be sure that the installation has unobstructed air flow into front air vent.
If ventilation is not adequate the normal performance of the product may be
impaired or prohibited.
■ Install the product in such a way to prevent the ingress of rodents and vermin as
damage caused by them may result in fire.
■ Install the cabinet door to the refrigerator in such a way to maintain a 5mm gap
between the edge of the cabinet door and any adjacent wall.
■ Use the specified dimensions for the Integrated door panels. Oversized integrated
door panels may sag or cause interference with the correct operation of the
product.
■ Check there is no lean on the product door after attaching the Integrated door
panels. Check to see that the gasket of the fridge/freezer is properly attached.
■ Use Integrated panel material of sufficient strength to maintain integrity of support
screw/bolts under the weight of the panels. i.e. don't use material that will allow the
screws to be pulled out easily from the weight of the panels.
■ Use Cabinet material that is sealed and won't warp or twist from the heat generated
by the product or from the moisture produced by opening and closing the
refrigerator doors.
■ Make sure surrounding cabinet work is square (within 1mm of horizontal or
vertical). Make sure the base plate that the product is placed on is of sufficient
strength to not bow or warp under constant weight of the product. Bowing or
warping may result in the product not being square with surrounding cabinet work
causing interference with the opening and/or operation of the product.
■ Installation or removal of this product will require the cooperation of two persons.
■ For safety reasons keep children away from the installation location and all
installation materials during installation.
■ Be sure to keep the installation location neat and tidy, keep screws in a single
location and take them only as needed to prevent injury from screws laying around.
■ Do not connect product via an extension cord or multi adapter due to risk of fire.
■ Test run product prior to installation to assure its correct operation.
4
2. Components to install
Parts prepared
before installing
cabinet case
① Top cover
② Hinge stand
1 unit
Parts related with
case after
inserting cabinet
case
2 units
⑤ Hinge cover
L : 1 unit
R : 1 unit
Parts related with
integrated
cabinet doors
after inserting
product into
cabinet case
⑭Depth adjust
bracket cover
Parts related with
finishing work
2 units
adjust Bracket
⑥ Bracket case cover ⑦ Depth
(hole size = 5.5mm)
⑩ Top bracket ⑪ Top bracket cover
⑮ Cap screw
⑧ Case cover
L : 1 unit
R : 1 unit
2 units
1 unit
1 unit
④ Depth adjust Bracket
(hole size = 8mm)
1 unit
1 unit
⑨ Paper jig
③ Bracket case
⑫ Depth adjusting ⑬Depth adjusting
bracket
bracket cover
1 unit
2 units
2 units
⒃ Hinge front
cover
⒔ Air path cover
4 units
1 unit
⒕ Gasket
4 units
2 units
2 units
ⓐ Wood bolting screw
ⓑ Wood bolting screw
ⓒUpper bracket bolting screw
2 units
ⓓ Height adjusting nut
Spec
Quantity
Spec
Quantity
Spec
Quantity
Spec
Quantity
D4×L16
2
D4×L12
16
D4×6.5
4
M5
4
ⓔ Hinge bolting screw
ⓕ Horizontal adjusting leg bolting screw
ⓖ Spanner
Spec
Quantity
Spec
Quantity
Spec
Quantity
M5
6
D4×L14
4
-
1
Cross (+) driver
These tools are
required but
not supplied
2m tape rule
5
3. Assembly/Disassembly diagram of
Built-in refrigerator
1
8
2
5
11
4
10
4
13
18
12
18
13
12
2
15
3
15
6
17
7
7
14
14
6
4. Dimension of Built-in refrigerator
and cabinet
400m
m or
※ The overall thickness of this figure is based
on 15mm.
longe
r
m
50m
※ The cabinet dimension should comply with
the figure.
600m
m
ger
r lon
mo
m
0
58
595m
m
1775 mm
5
Inne 60mm
r dim
ens
ion
1830mm
or longer
1688.5 mm
1800mm
or longer
Inner dimension
39mm
554
mm
m
0m
/56
545
400m
m or
longe
r
mm
50
50mm
400
mm
Caution
The dimension of integrated door panels changes if there is a change of cabinet material thickness.
Thickness of Cabinet Case
18mm
20mm
Dimension of Integrated Door Panel
1836mm or longer
1840mm or longer
- Both the main body of the cabinet and the integrated door panel must be separated.
- The integrated door panel may sag if it is larger than the specified size.
- Install the product in such a way that all cabinet work is level both horizontally and vertically.
7
5. Installing the built-in refrigerator
■ Construct the cabinet work in accordance with these dimensions to guarantee
adequate ventilation for reliable heat exchange for product.
1. There must be unobstructed pathways
for air circulation to enter through
bottom inlet and escape through upper
outlet.
2. Ensure that No. ¡ path can be
obtained in the cases where the No. ¨
path cannot be used.
3. Ensure that the surface area of the inlet
and outlet ports for the No. ¨, ¡ air
paths are more than 200cm2.
2
Ceiling
min. 50mm
1
min. 30mm
Caution
Wall
Required conditions for base of cabinet.
- Bottom surface :
It is required to use T 20mm to obtain strength.
- Space stand :
Ensure that the base is reinforced to the extent
that it can support up to 200KG (Product + Food
+ Integrated Cabinet Doors + Shock of opening
and closing doors)
- Level :
The base must be level to assure the uniform
downward pressure and distribution of weight to
alleviate warping of the base. Warping may
hinder the operation of the products doors.
Secure the
ventilating hole
min. 200cm2
min. 30mm
■ Floor plan of cabinet and the maximum opening of the door
252mm
min 560mm
Inner side of cabinet
Side wall of cabinet
min 580mm
Wall
600mm
Side wall of cabinet
min 580mm
600mm
Wall
Hinge Hinge
base
Cabinet door
min 560mm
Inner side of cabinet
3mm
237mm
(Distance from
the wall when
completely
opened)
Special case
Wall
Wall
Standard
Caution
- Securely fix the side panel of the cabinet to the wall or adjacent cabinet. Because the product is anchored
to the cabinet with the screws from the hinge, make sure the side panel thickness is 30mm or more.
(Additionally, If the fridge and freezer are installed side by side, make sure an additional panel of 15mm is
added between them to assure a combined thickness of 30mm between them.) If the side panel is to thin,
the products may be damaged if the screws pass through the panels and touch the other fridge/freezer.
8
6. Procedure to install
1) Preparing before installing the refrigerator
1. Installing the top cover of the refrigerator
1) Fold the top cover of the refrigerator ¨ in
advance as shown at the figure.
45mm
45mm
1
2) Fix the refrigerator top cover ¨ with the
wood bolting screw ⓑ (3 places) at a
point 45mm in from interior edge of
cabinet at each end and also in the
middle.
(The thickness of the cabinet material
determines the way the top cover ¨ is
cut. Please take notice of the below
"reference" for the correct cutting of the
top cover.)
1
b
45mm
※ Reference
AB
CD
1
Door opened to the right
If the thickness of the cabinet material is
18mm, cut at A, but if it is 20mm, cut at B.
Door opened to the left
If the thickness of the cabinet material is
18mm, cut at D, but if it is 20mm, cut at C.
9
6. Procedure to install
1) Preparing before installing the refrigerator
- Assemblely bracket
(Figure 1)
② Tighten the screw
① Tilt to back
- Assemblely cover
(Figure 2)
Tighten the screw
firmly
After separating the double
sided tape, tighten the screw
firmly
There is no hole for screw on
the outer cabinet. Screws need
to be tightened firmly.
10
6. Procedure to install
1) Preparing before installing the refrigerator
2. Insert the hinge base ② into the hinges (two spots). (See Figure 1)
(If the thickness of the cabinet is 20mm, do not install the hinge base ②.)
3. Lean the refrigerator backward and then fix the depth adjust bracket ⑦ at the bottom (two
spots) of the refrigerator door by using the hinge screws ⓔ as shown at the figure.
If there is any excess length on the power cord, hang the excess up on a holder, or hook so that it
cannot be crushed or damaged by the product when it is installed into the cabinet.
(Figure 3)
2
2
7
e
e
7
2) Case-related Work After Inserting Refrigerator
4. Draw the power cable through the back of the cabinet.
Be careful that the power cord is not trapped beneath the
refrigerator as you install it into the cabinet. The cord may
be crushed and damaged resulting in a fire hazard. Hang it
on the rear holder if possible.
cabinet
Hinge base②
5. Insert the refrigerator into the cabinet so that the
end of the hinge stand ② align to the front part of
the cabinet.
Caution must be taken not to jam your hands between
refrigerator and cabinet when inserting refrigerator into
cabinet.
Hinge
Front side of
the cabinet
The top of the cabinet (floor view)
11
6. Procedure to install
2) Cabinet related work after inserting the refrigerator
6. Adjust the horizontal/vertical level of the refrigerator by turning the level adjusting leg(
1⃞ When the unit tilts backwards. Adjust
by turning the horizontal adjusting
leg anti-clockwise since the
refrigerator leans backward.
1⃞
2⃞ When the unit tilts forwards. Adjust
by turning the horizontal adjusting
leg clockwise since the refrigerator
leans forward.
2⃞
Check that the depth dimensions of the front part of the cabinet and the front part of
refrigerator door are constant by using the spanner ⓖ (See Fig. 4).
Front of cabinet
(Figure 4)
Front of refrigerator door
4mm
Spanner
3.5mm
Front of
refrigerator door
Front of
cabinet
3mm
ⓖ
g
For mounting
the front of
the cabinet
For mounting
the refrigerator door
).
12
6. Procedure to install
2) Cabinet related work after inserting the refrigerator
7. Make sure that the end of the hinge base ②
is aligned with the front right of the cabinet.
cabinet
Hinge base②
Hinge
Front side of
the cabinet
8. Fix the top hinge and the bottom hinge by
the hinge screws ⓕ (four spots).
(See Figure 5)
Be careful when working on hinges as you
may be injured by the hinge operation if the
door moves.
(Figure 5)
f
9. Check that the left / right depth interval as
in Figure 6 is constant by using a ruler.
(Figure 6)
13
6. Procedure to install
3) Integrated door panel related work
10. Place the paper jig ⑨ on the reference line of the paper jig at the rear side of the
furniture door. (See Figure 7)
※ Reference - Place the reference line of the paper jig at 1595mm from the floor of the cabinet.
- If the integrated door panel is long, place the reference line of the paper jig at
1595mm plus ‘A’ from the floor of the furniture.
(Figure 7)
9
Reference line
of paper jig (for
the right hinge)
Reference line
of paper jig (for
the left hinge)
1595mm
A
11. Mark two points in the paper Jig ⑨ on the
integrated door panel. (See Figure 8)
(Figure 8)
⑨
Before fixing with the wood screw ⓑ,
double check the indicated point is located
in an accurate position.
12. After removing the paper jig ⑨ , fix the top
bracket ⑩ of the integrated door panel by
using the wood screw ⓑ (4 places) with the
top two holes lined up to the marked spots
(from the paper jig) on the integrated door
panel. (See Figure 9)
※ Reference - If you need to re-position top bracket
due to incorrect positioning. Align
top two holes to remarked position
(from jig) but use alternate holes to
fix to assure screws hold firmly.
(Figure 9)
10
b
b
14
6. Procedure to install
4) Refrigerator door related work
13. Insert the height adjusting nuts ⓓ (two spots at the bottom) onto the height adjusting
screw, and then place the top bracket ⑩ of the integrated door panel onto the height
adjusting screw of the top of the refrigerator door. Use the height adjusting nut to adjust
the height of the integrated door panel and set the level. (See Figure 10)
(Figure 10)
Be careful to align the top
bracket holes onto the
adjusting screws to
prevent the integrated
door panel from falling
and causing personal
injury or damage to the
integrated door panel.
10
d
14. Check the place where the hole of the depth adjusting bracket ⑫ is aligned with the
hole of the refrigerator door (Figure 11), and fix the depth adjusting bracket ⑫ to the
left/right (four spots) of the integrated door panel with the wood screw ⓑ. (Figure 12)
※ Reference
The door hole is located at
1050mm from the door floor.
(Figure 11)
Furniture door
Refrigerator door
12
(Figure 12)
10
12
1050mm
b
15
6. Procedure to install
4) Refrigerator door related work
15. Loosely fix the top bracket ⑩ with the height adjusting nuts ⓓ (Figure 13), and adjust the
depth gap between the integrated door panel and the front of the cabinet to 4mm. At this
time, adjust the location of the integrated door panel so as not to touch or make contact
with the face of the cabinet when opening/closing the door.
g
d
10
d
Forward/
Backward
Top/Down
Adjust
Left/Right
(Figure 13)
16. Use the spanner ⓖ to check the dimension. (See Figure 14)
(Figure 14)
Parallel
Parallel
Cooling
room
Furniture
door
g
4mm
17. If the dimension is not correct, loosen the height adjusting nuts ⓓ, the door screw ⓐ
and the wood screw ⓑ, and repeat the work starting from Step 12.
18. Place the depth adjusting bracket ④ as shown at the figure, fix it with the bracket screw
ⓔ (two spots), and fix with the top bracket screws ⓒ (four spots). (See Figure 15)
Secure the height adjusting nuts ⓓ to fix the top bracket ⑩.
e
4
(Figure 15)
c
16
6. Procedure to install
4) Refrigerator door related work
19. Move the integrated door panel in or out to
adjust the depth gap to 4mm (See Figure
14), and fix the depth adjusting bracket ⑫ to
both sides (two spots) of the refrigerator door
with the door screw ⓐ. (Figure 16)
(Figure 16)
12
a
20. Use the wood screws ⓑ (four spots) to the depth adjusting bracket ⑦, move the integrated
door panel in or out to adjust the depth gap to 4mm (See Figure 14, Figure 17), and secure
the loosely fixed bracket screw ⓔ (Figure 1) to fix the depth adjusting bracket ⑦.
Depth gap
b
7
(Figure 17)
21. Place the top bracket cover ⑪ on the door top and place the depth adjusting bracket
cover ⑫ and ⑭ on the middle and the bottom of the door respectively. (See Figure 18)
Door top
⑪
⑫
Door center
⑬
⑭
Door bottom
(Figure 18)
⑭
17
6. Procedure to install
5) Installation checkup and finishing work
22. Insert the ventilation cover ⒔ into the rectangular hole on the front of the cabinet base.
23. Attach the gasket ⒕ as shown
in the figure. Attach it to the
opposite side from the hinge
side. If the gasket is to long,
cut it to the necessary length
required.
1800mm
24. Insert the screw cap ⑮ as shown at the figure.
18
18
18
15
15
6
6
17
After securing screws,
install screw cap.
(Figure 19)
18
6. Procedure to install
6) Changing the opening direction of the refrigerator door
※ Perform work for changing the door before installation.
1. Loosely release the screws ❶, ❸
of the hinge on the case part of
the refrigerator and then separate
the door by pushing it to the right
(See Figure 20).
1
2
2. Release the screws No. ❶, ❸
completely and then fix them
loosely to the reverse side (See
Figure 21)
3. Loosen the screws ❷ and ❹
fixed to the door to disconnect
the hinge.
(Figure 20)
4. Move the separated hinges
(Figure 24) diagonally and fix it to
the door by turning the hinge by
180°. Fix the hinge to the door
with screws No. ❷, ❹.
5. Align the door hinge with screws
No. ❶, ❸ on the case and push
from left to right to lock in.
6. Adjust the up/down or the
left/right interval of the
refrigerator door so that leaning
should not occur to either side,
and then tighten screws.
7. After fixing the hinge, insert the
screw caps ⑮ (two spots) at the
opposite holes of the hinge.
(Figure 21)
19
6. Procedure to install
7) Integrated door panel gap
※ When installing two pieces of furniture closely, keep the gap between them 5mm
or more.
5mm
P/No.: MFL58003408
Download PDF