LG | VR6140LVM | LG VR6140LVM Owner’s Manual

OWNER’S MANUAL
CLEANING ROBOT
Before using, please carefully read the Safety Precautions pages to
allow for safe operation of the product. After reading the operation
manual, please keep it in an easily accessible location.
VR6140LVM
www.lg.com
FEATURES
Camera sensor
(upper, lower section)
Images of the ceiling and floor are obtained from the sensors of the upper
and lower cameras, and through this, the location of HOM-BOT 2.0 will be
confirmed, therefore, elaborate cleaning can be accomplished for every part
of the room.
As the noise levels are at a quiet 60 dB(A), cleaning can be performed at
night.
*60 dB(A)
The HOM-BOT 2.0 has two auto cleaning modes that can be selected by
the user.
*Spatial expantion mode, zigzag mode
“Please, check
the dust bin.”
The HOM-BOT 2.0 also has voice confirmation and instruction that can be
easily understood by the user.
The use of the ultra microfiber mop accessory allows finer dust to be
collected from hard flooring. (option)
HOM-BOT 2.0 memorizes the location for cleaning.
* Minimizes the overlapping of cleaning area
A problem has
been found in the
acceleration sensor.
HOM-BOT 2.0 will start self-diagnosis and will inform you with the voice.
CONTENTS
1
BEFORE THE USE
4
ADDITIONAL INFORMATION
2~4
Safety precautions
31~33 Troubleshooting
5
Included with product
34
6~7
Parts description
8~9
Button functions
10
Display status information
11
Before you start
12
Overview
2
METHOD OF USE
13
How to install the home station
14
How to turn the HOM-BOT 2.0 power supply on & off
15
How to start and stop cleaning
16~17 How to charge the battery
18
Cleaning modes
19
Auxiliary cleaning modes
20
Timer cleaning
21
Mop cleaning (option)
22
Location search function
23~24 Smart-diagnosis mode
3
HANDLING METHOD AFTER USE
25
Cleaning the dust bin
26
Cleaning the dust bin filter
27
Cleaning the brush
28
Cleaning the sensor/charging terminal
29
Cleaning the side brush
30
Cleaning the ultra microfiber mop (option)
Before you call for service
5
REFERENCE
35
Product specifications
36
Open source software notice
SAFETY PRECAUTIONS
The purpose of the safety precautions described below is for the user to use the product safely and
correctly to prevent any unexpected risk of injury or damage.
Basic safety precautions
After reading this manual, please keep it in an easily accessible location.
This is the safety alert symbol. This symbol alerts you to potential hazards that can result in
property damage and/or serious bodily harm or death.
WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
WARNING
1. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
2. C
hildren should be supervised to ensure that they do
not play with the appliance.
3. If the supply cord is damaged, it must be replaced by
LG Electronics Service Agent in order to avoid a hazard
4. This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
For your safety, do not remove the
battery from the HOM-BOT 2.0. If
you need to replace the battery or the
HOM-BOT 2.0, take it to the nearest
authorized LG Electronics service
center or dealer for assistance.
Failure to follow this warning can
cause fire or product failure.
2
Never use the HOM-BOT 2.0 with
a battery and/or home station from
any other product than the
HOM-BOT 2.0.
Doing so can cause fire or product
failure.
SAFETY PRECAUTIONS
WARNING
Make sure the power cord of the
home station is not crushed under a
heavy object or damaged by contact
with sharp objects.
Failure to follow this warning can cause
electric shock, fire or product failure.
If the power cord is broken, do not
plug it in. Take the product to an LG
Electronics Authorised service repairer.
Do not place the home station and
the HOM-BOT 2.0 near a heating
device.
Doing so can cause product
deformation, fire, or product failure.
Do not force the power plug to
bend. Do not use the power plug
when it has been damaged or
loosened.
Doing so can cause fire or product
failure.
Do not touch the power plug with
wet hands.
Doing so can cause electric shock.
Do not use the HOM-BOT 2.0 when
candles or fragile objects are placed
on the floor.
Doing so can cause fire or product
failure.
Always use a dedicated outlet with
5 A or above.
If multiple appliances are connected
to an outlet simultaneously, they
can generate enough heat to cause
a fire.
When pulling out the power plug,
always pull it out by grabbing the
plug, not the cord. When pulling out
the power plug, do not to touch the
prongs with your fingers.
Doing so can cause an electric
shock.
Do not allow children or pets to play
with or rest upon the HOM-BOT 2.0
at any time. Do not use the HOM-BOT
2.0 while an object is hanging from it.
Doing so can cause injury or
product damage.
Gasoline
Detergent
Do not spray or suck in inflammable
materials, surfactants, or drinking water
in the vicinity of the HOM-BOT 2.0.
Doing so can cause fire or product failure.
* Inflammable materials: gasoline,
thinner, etc.
* Surfactant: detergent, articles for
bath, etc.
Do not insert any part of the body,
such as a hand or foot, below the
brush or wheels of the
HOM-BOT 2.0 while in use.
Turn the power supply off
immediately if any abnormal sound,
odor, or smoke is generated from
the HOM-BOT 2.0.
Failure to do so can cause fire or
product failure.
Do not operate the HOM-BOT 2.0
in a room where a child is sleeping.
Doing so can cause injury or
product damage.
Doing so can cause injury or
product damage.
Do not operate the HOM-BOT 2.0
on narrow and high furniture such
as a wardrobe, refrigerator, desk,
table, etc.
Do not leave Children or pets near
the HOM-BOT 2.0 unsupervised.
Doing so can cause injury or
product damage.
Doing so can cause injury, product
failure or damage which is not
covered by the warranty.
CAUTION
Frequently empty the dust bin and
maintain its cleanliness.
Do not drop the HOM-BOT 2.0 or
subject it to strong impacts.
The dust collected in the dust
bin can trigger allergies and may
contain harmful insects.
Doing so can cause injury or
product failure not covered by the
warranty.
3
SAFETY PRECAUTIONS
CAUTION
Use the HOM-BOT 2.0 indoors
only.
Do not expose the HOM-BOT 2.0
to cold temperatures (less than
-5 C) for a long period of time.
Using it outdoors can cause product
failure and irreparable damage to
the unit.
Doing so can cause product failure.
Close the cover of the dust bin on
the main unit before start cleaning.
Remove any cable or long string on
the floor.
If the cover is not closed, it can
cause injury or product damage.
Cable or string can get tangled in
the wheels of HOM-BOT 2.0 and
cause product failure or the cord to
be disconnected.
In rare cases, the HOM-BOT 2.0’s
brush can damage the carpet. If
this happens, immediately stop the
cleaning operation.
Do not allow the HOM-BOT 2.0 to
sweep up liquids, blades, thumb
tacks, hot ashes, wooden shavings
etc.
When a carpet has long tassels, the
tassels can be damaged.
These items can cause product
failure.
Do not let the main unit and
charging terminal of the home
station come into contact with
metallic objects.
Do not put sharp objects into the
opening of the HOM-BOT 2.0’s
supersonic sensor.
Doing so can cause product failure.
Doing so can cause product failure.
Do not put water, detergent, etc.
into the HOM-BOT 2.0.
Do not use the HOM-BOT 2.0 when
the dust bin is completely filled up.
Doing so can cause product failure. Do
not put any water or detergent on the
HOM-BOT 2.0. If liquids get inside of
the HOM-BOT 2.0, turn off the power
supply and contact an LG Electronics
sales agent or customer care center.
Doing so can cause product failure.
If the floor is wet or has wet spots,
wipe them up before using the
HOM-BOT 2.0. Do not use the
HOM-BOT 2.0 on a wet surface.
When the robot cleaner is
operating, it may hit the chair leg,
desk leg, table leg or other narrow
pieces of furniture.
Failure to do so can cause product
failure.
For quicker and better cleaning,
place the dining chairs on top of the
dining table.
When attaching the mop, do not
block the bottom camera sensor.
Blocking the bottom camera sensor
may not allow the product to work
smoothly.
Tip
4
Check the following items before use:
• Empty the dust bin after if fills up.
• Remove any cables or long strings from the floor.
• Remove any moisture from the floor before cleaning.
• Close the cover of the dust bin before cleaning.
•R
emove fragile or unnecessary objects from the room to be cleaned.
For example, remove expensive ceramics and valuables from the floor.
• Confirm whether the battery has sufficient power, and if it is low, recharge it.
•C
lose the doors of any room that you do not want the HOM-BOT 2.0 to enter.
During cleaning, the HOM-BOT 2.0 may enter another room and continue cleaning.
• Do not use this product in the room where a child is sleeping alone. The child can be hurt.
•R
emove towels, foot towel or any other thin cloth from the floor as they can get caught by the brush.
•C
leaning will not proceed smoothly on carpets or rugs with tassels or carpets thicker than 8 mm
(0.315 in). It may be more convenient to rearrange or remove them before using the product.
INCLUDED WITH PRODUCT
HOM-BOT 2.0
Remote controller
Home station
s Figures can be different from actual objects.
OWNER’S MANUAL
CLEANING ROBOT
Before using, please carefully read the Safety Precautions pages to
allow for safe operation of the product. After reading the operation
manual, please keep it in an easily accessible location.
www.lg.com
Dust bin filter (spare)
Quick guide
Brush for cleaning filter
Mop plate
Operation manual
Ultra microfiber mop
(2 pieces) (option)
Side brush
(2 pieces)
Dry cell for
remote controller
(2 units of AAA size)
5
PARTS DESCRIPTION - HOM-BOT 2.0
Plan view
Dust bin cover button
Dust bin cover
Upper camera sensor
Manipulation button
Detecting sensor of home station &
receiving sensor of remote controller
Front view
Ultrasonic sensor
Rear view
Ventilation port
Bottom view
Cliff detection sensor
Charging terminal
Brush
Side brush
Wheel
Lower camera sensor
Mop plate fixing hook
Battery
Power switch
s Figures can be different from actual objects.
6
PART DESCRIPTION – HOME STATION / DUST BIN
Home station
Remote controller holder
Charging terminal
Reset button
Power cord fixing hook
Dust bin
Dust bin handle
Dust bin cover
Suction port cover
Dust bin cover
opening button
Sponge filter
HEPA filter
s Figures can be different from actual objects.
7
BUTTON FUNCTIONS – HOM-BOT 2.0
8
TIMER
• Use the TIMER button to start cleaning after a set amount of time has elapsed.
• The timer can be set from 1 to maximum of 12 hours in 1 hour units.
• If the timer is set whilst the unit is away from the home station, the cleaning
time will be reduced. Therefore use the product while attached to the home
station as much as possible.
• The timer setting is inoperative if there is no dust bin.
START/STOP
•P
ress the START/STOP button to turn the HOM-BOT 2.0 on/off or start/stop
cleaning.
• Press the START/STOP button while the HOM-BOT 2.0 is on and it will
automatically start cleaning.
• If the START/STOP button is pressed during automatic cleaning, the HOM-BOT
2.0 will stop cleaning.
• Press and hold the START/STOP button for approximately two seconds to turn
off the HOM-BOT 2.0.
• If the button is pressed while in the timer mode, the reservation will be canceled.
• Pressed during Smart-diagnosis mode, the Smart-diagnosis will stop.
HOMING
•P
ress the HOMING button to move the HOM-BOT 2.0 to the home station for
battery charging.
• When cleaning is complete or the battery is low, the device will automatically
move to the home station to charge the battery even without pressing the
HOMING button.
• The Smart-diagnosis will start when attached to home station and pressed for
3 seconds.
• When the button is pressed after Smart-diagnosis is completed, the voice
information will be repeated.
BUTTON FUNCTIONS – REMOTE CONTROL
START
The HOM-BOT 2.0 will start
cleaning
HOMING
The HOM-BOT 2.0 will move to the
home station for charging.
SPOT
Cleaning will concentrate
within a space of about 1 m
(3.28 ft). (Page 19)
TIMER
The timer can be set from 1-12
hours in the future. (Page 20)
Directional button
The HOM-BOT 2.0 will
move as desired by the
user: to front, rear, left, and
right sides for cleaning.
STOP
If the HOM-BOT 2.0 is in operation
it will be stopped.
If it has been set for timer cleaning,
the reservation will be canceled.
Cell by Cell
The HOM-BOT 2.0 will
clean using the spatial
expansion style.
(Page 18)
Zigzag
Cleaning will be performed by
the HOM-BOT 2.0 in the zigzag
traveling fashion. (Page 18)
Tip
• The HOM-BOT 2.0’s power supply cannot be turned on with the remote control.
• If the main unit is turned off, the remote control will not activate the unit.
• To turn the cleaner on from the stand by mode or off during cleaning, use START/STOP
button on the top of HOM-BOT 2.0.
• In order to do spot cleaning, timer cleaning, zigzag cleaning, and spatial expansion cleaning,
you must first stop the operation of the HOM-BOT 2.0.
9
DISPLAY STATUS INFORMATION
Power Icon
• Lights on when
the power is on,
and flickers when
charging.
Timer icon
• This indicates when timer
cleaning has been set up.
(Page 20)
Tip
10
Battery Icon
• Flickers when
charging is
needed.
•O
nce the cleaning mode is selected, it will be kept in memory even when the power is
turned off.
• To cancel the timer setting, press the STOP button on the remote control or the START/
STOP button on the HOM-BOT 2.0.
BEFORE YOU START
Check these items before cleaning
• Do not use this device in a room where a child is left alone. The child could be injured.
• Remove fragile or unnecessary objects from the room to be cleaned.
Especially, remove expensive ceramics and valuables from the floor.
• Close the cover of the dust bin before cleaning.
• Remove any moisture that might be on the floor.
• Remove cables, strips, towels, mat etc. from the floor so they will not get caught by the brush.
• Confirm whether battery charge is sufficient, and if it is low, recharge it.
• Empty the dust bin if it is full.
• Close the doors of any room that you do not want the HOM-BOT 2.0 to enter. During cleaning,
the HOM-BOT 2.0 may enter another room and continue cleaning.
• When the mop is attached, HOM-BOT 2.0 will not be able to go over thresholds of 5 mm or higher.
If you are not planning to use the mop for cleaning, separate the mop before using HOM-BOT 2.0.
– +
+ –
Loading the remote controller battery
1. Open the battery cover by lifting the rear hook of the remote controller.
2. Insert two AAA batteries, checking for +, - nodes while loading.
3. Close the battery cover completely so that the batteries will not fall out.
– +
+ –
Precautions while using the remote control
•
•
•
•
Only press one button at a time.
Do not drop or subject it to forceful impact.
Do not store it near devices that give off heat, fire or hot air.
Certain fluorescent lamps, such as 3 wavelength fluorescent lamps, can interfere with the activation of the
remote control. Therefore, use it as far away as possible from such lamps.
• If the remote control is far from the HOM-BOT 2.0 when activated, it may fail to operate properly. Use the
device within 3 m (9.84 ft) of the HOM-BOT 2.0 if possible.
– +
+ –
11
OVERVIEW
1
Insert the power cord plug into an outlet and locate the
station against a wall. If power is not supplied to the
home station, the HOM-BOT 2.0 will not charge.
2
Turn on the power supply of the HOM-BOT 2.0.
(Page 14)
3
Check the dust bin.
4
Start cleaning. (Page 15)
5
Automatic charge. (Page 16-17)
6
< Warning >
12
Install the home station. (Page 13)
1
1
2
Turn on the power switch located on the bottom of
the HOM-BOT 2.0 and press the upper START/STOP
button to turn on the power supply.
※ If the power supply is not turned on, refer to page 14.
Check the cleanness of the dust bin before starting
the cleaning and close the cover of the dust bin on the
main unit.
Press the START/STOP button once again while
the HOM-BOT 2.0 is turned on. You will hear the
announcement of cleaning and cleaning will begin.
The HOM-BOT 2.0 will self-diagnose and automatically
return to the home station to recharge before the
complete discharge of the battery. It takes approximately
three hours to charge the battery.
Use the cleaning mode and auxiliary functions.
(Page 18-22)
With the HOM-BOT 2.0 and remote controller button,
the cleaning method and auxiliary functions can be used.
Zigzag or spatial expansion (cell by cell) cleaning method
can be selected for the cleaning mode and manual
cleaning, spot cleaning, timer cleaning and micro fiber
mop cleaning can be selected as an auxiliary function.
When HOM-BOT 2.0 is operated with the cover of the dust bin open,
it can cause an injury or serious damage to the product.
Flickering
HOW TO INSTALL THE HOME STATION
How to Install the Home Station
1. P
osition the home station against a wall, to prevent sliding during
docking, on hard level flooring.
R
emove objects within 1 m to the right and left side and within
2 m to the front.
1
1
2
2. Plug the power cord into an outlet.
rap the power cord around the fixed hook on the back side of
W
the home station or along the wall surface so that the travel path
of the HOM-BOT 2.0 will not be obstructed.
Fixing hook of power cord
3. Fix the home station against the wall so that it does not move.
4. When the remote controller is not used, store it on the remote
controller holder on the home station.
Tip
< Warning >
• Always keep the home station plugged in. If the home station is not plugged in, the
HOM-BOT 2.0 will not return to the station to charge automatically.
Do not operate the HOM-BOT 2.0 or its Home Station if it has a damaged cord or
plug, if it is not working properly, or if it has been damaged or dropped. To avoid
hazard, the cord must be replaced by LG Electronics, Inc. or a qualified service person.
13
HOW TO TURN THE HOM-BOT 2.0 POWER SUPPLY ON & OFF
Turning on the main power supply
To turn the power supply on, turn the HOM-BOT 2.0 upside down
on a smooth/soft surface and check whether the main power
supply switch is turned on.
※ Please make sure to remove the dust bin before turning over
the main body. Otherwise, the dust in the dust bin may fall out.
If the main power supply switch is turned off, turn on the switch.
※W
hen turning on the power switch, do not press the button
located at the upper section of the HOM-BOT 2.0. Operation of
the button can be delayed.
※ Turn off the power switch if the HOM-BOT 2.0 will not be used
for a long period of time, in order to protect the battery.
Turning on from Stand By power.
When the HOM-BOT 2.0 is not at the Home Station, and is in the
Stand by mode, press the ‘START/STOP’ button for more than
1 second. The HOM-BOT 2.0 will be turned on and a melody will
be sounded.
※ HOM-BOT 2.0 will automatically return to the home station to
recharge when the charge is low during operation, or if left idle
with no cleaning command for more than 10 minutes.
※ Do not operate HOM-BOT 2.0 on tables or desks. It will result in
an injury or damage to the product when it starts to search for
the home station after 10 minutes.
Be sure to turn the main power off from the on/off switch on
the underside of the unit when placing HOM-BOT 2.0 on high
furniture for storage purposes.
Turning off the power supply (stand by mode)
Press the START/STOP button for two seconds while the
HOM-BOT 2.0 is turned on. A melody will sound when the power
is turned off.
Tip
14
• If the power cannot be turned on, do the following.
- Turn on the power switch if off, and wait for more than 3 seconds.
- Press the ‘START/STOP’ button when the power switch is turned on.
- If the power is not turned on or if there is no display but only the “Ting” sound, put the
HOM-BOT 2.0 on the home station.
- If there is no change even when HOM-BOT 2.0 is attached to the home station, press the
reset switch located on the rear side of the home station for 3 seconds while the HOMBOT 2.0 is attached on the home station.
HOW TO START AND STOP CLEANING
Using the buttons on the HOM-BOT 2.0
After the HOM-BOT 2.0 is turned on, press the START/STOP button
to begin cleaning. A melody will sound and cleaning will begin.
Press the START/STOP button during the cleaning cycle to stop
cleaning.
※ When the ‘START/STOP’ button is pressed while the power supply
of the HOM-BOT 2.0 is turned off, the power will be turned on.
Press the ‘START/STOP’ button one more time to start cleaning.
Using the remote control
After the HOM-BOT 2.0 is turned on, press the START button on the
remote control. A melody will sound and cleaning will begin.
Press the STOP button during the cleaning cycle to stop cleaning.
※ The HOM-BOT 2.0 cannot be turned on from Stand By, by using
the remote control when the power of the HOM-BOT 2.0 is off.
When the power is off, press the ‘START/STOP’ button on the
upper side of HOM-BOT 2.0 to turn the power on and to allow the
remote to be used.
※D
uring cleaning, collisions can happen when the sensor cannot detect objects because of their shape (Thin
chair and table leg, furniture corner). When this happens, the internal impact detecting sensor will avoid
the obstacles by using a backward motion.
※ If the HOM-BOT 2.0 is set to start cleaning at a location away from the home station, put the device on
a flat floor in order to prevent a malfunction of the obstacle detecting sensor. In addition, start cleaning
from a location where there are not any obstacles such as curtains or walls within 30 cm (11.8 in) of the
HOM-BOT 2.0.
Tip
For best results:
•B
riefly scan the area to be cleaned for big and small objects that will cause difficulty for the
HOM-BOT 2.0.
• If cleaning is started when the HOM-BOT 2.0 is at the home station, the device can rapidly
be returned to the home station as the current home position has been accurately read.
•F
or the safety of the HOM-BOT 2.0, a step height of more than 10 mm (0.4 in) cannot be
crossed.
• When then mop plate is fitted, the HOM-BOT 2.0 cannot go over door sills or step treads
that are higher than 5 mm.
15
HOW TO CHARGE THE BATTERY
Automatic charging
The HOM-BOT 2.0 returns to the home station at the
end of a cleaning cycle or when its battery is running low.
※ In the event that the unit returns to the Home Station
due to a low battery, cleaning will be started, after the charging,
from the nearest place of the area which has not been cleaned
before. (Page 17)
※ If HOM-BOT 2.0 is unable to dock to the home station on its first
attempt, it will try again until it docks successfully.
※ When HOM-BOT 2.0 completed all areas that it can clean, it will
return to the home station even when the battery level is not low.
※ HOM-BOT 2.0 will automatically return to the home station to recharge when it's left uncharged or without
cleaning order for more than 10 minutes.
※ Do not operate HOM-BOT 2.0 on tables or desks. It may result in an injury or damage to the product
when it starts to search for home station after 10 minutes.
Be sure to turn the power off when placing HOM-BOT 2.0 on high furniture.
Manual charging
If using the HOM-BOT 2.0 for the first time or when charging the battery during cleaning, you can manually
charge the battery.
Method 1. Attach the HOM-BOT 2.0 to the home
station by aligning to the front side of the
home station. A melody sound will be
generated along with an audio message to
start charging.
※ If an audio message saying “Turn on the
main power switch on the bottom of the
unit” is generated repeatedly when the
HOM-BOT 2.0 is attached to the home
station, please check the power switch
and turn it on.
Method 2. When the HOMING button of the remote
control or the HOM-BOT 2.0 is pressed, the
charge process will start by announcing the
search for the Home Station and will then
attempt to return to it for charging.
※ If the HOM-BOT 2.0 commenced cleaning whilst away from the home station, and then the Homing
button is pressed from either the remote or the unit, it may take slightly longer to find the home station.
※ If the HOM-BOT 2.0 stays within 10 cm (3.9 in) of the front of the charging terminal while the power
supply is turned on, it will automatically be returned to the home station and charging will begin.
Tip
Take the following precautions when using the home station:
• If foreign material is covering the charging terminal, charging may not proceed smoothly.
Wipe the terminal from time to time with a dry cloth after the power plug is disconnected.
• To prevent electric shock, do not touch the charging terminal with any metallic objects.
• To avoid fire or electric shock, never disassemble or modify the home station.
• Do not to place the home station or power plug near to a heating appliance.
16
HOW TO CHARGE THE BATTERY
Remaining Battery Charge Indicator
The battery status is displayed as below.
• The Battery Icon flickers when charging is needed.
• The icon flickers when the device is charging.
• When charging is completed on the home station, the device only displays battery icon to save power.
Charging needed
Charging
Charging
complete
If the Battery is Not Charging
Check 1:
If the battery is not charging even when the HOM-BOT 2.0
is attached to the home station, check the following items.
- Turn the power switch on the bottom of the HOM-BOT 2.0
off once and then on again.
- Check the power lamp of the home station.
- Wipe the terminal on the home station with a dry cloth
Check 2:
If the battery is still not charging after the previous check,
try the following.
- Manually attach the HOM-BOT 2.0 to the home station.
-P
ress the reset button at the rear of the home station for
three seconds.
Charge
terminal
17
CLEANING MODES
Zigzag Cleaning
With zigzag cleaning, the total of the cleaning area will be
cleaned with the repetition of zigzag traveling.
If rapid cleaning is desired, use zigzag cleaning.
When pressing ‘ZIGZAG’ button on the remote controller,
zigzag cleaning will be started while zigzag cleaning icon is
indicated by the indication lamp.
Spatial Expansion Cleaning
With spatial expansion cleaning, the cleaning will be
performed by dividing the cleaning area into partial square
spaces.
If elaborate cleaning is desired, use spatial expansion
cleaning.
The HOM-BOT 2.0 starts 'Cell by Cell' cleaning mode
when, pressed 'Cell by Cell' on the remote.
The 1st stage:
The maximum outline of 3 m x 3 m of cleaning area
will be cleaned. (The size of outline will be changed in
accordance with the shape of the house inside.)
The 2nd stage:
Inside of the outline will be cleaned with zigzag traveling.
When the 1st, 2nd stages are completed, the inside of
the cleaning area will be cleaned through the repetition of
above cleaning method as the device is being moved to
the next cleaning area.
Tip
18
•O
nce set up, the cleaning mode will be kept in memory even after the power supply is
turned off.
•D
uring operation, if a mode change is required, press the STOP button and then select the
mode.
AUXILIARY CLEANING MODES
Manual cleaning
This method of cleaning involves manually moving the HOM-BOT 2.0 by pressing the directional (arrow)
buttons on the remote control.
The interior space will be cleaned by the HOM-BOT 2.0 as it is being moved to the front, rear, or rotated to
the left and right side according to the input of the directional buttons.
If it meets an obstacle during manual cleaning in a forward motion, it stops.
Spot Cleaning
Use this cleaning method when concentrated cleaning of a small interior space is required.
After moving the HOM-BOT 2.0 to the location to be cleaned, press the SPOT button on the remote
control.
The spot cleaning icon will illuminate on the HOM-BOT 2.0, and concentrated cleaning will be performed
for a space within a radius of 1 m (3.28 ft).
※ During charging, the spot cleaning button on the remote control will not activate.
It stops at the started position after
completing the cleaning(takes 4~5 min.).
※ The following device show weaker on inhalation
than ordinary vacuum cleaner, but with rotation
brush and side rotation brushes, the device shows
similar performance on cleaning as ordinary
vacuum cleaner.
Brush
Side brush
19
TIMER CLEANING
Set the timer to schedule the cleaning and begin in 1-12 hours.
The timer setting is inactive if there is no dust bin.
1. B
y pressing the TIMER button on the remote control
or the HOM-BOT 2.0, a cleaning time can be
scheduled.
2. Adjust the time as much as desired by multiple presses of the TIMER button. Each time you press the
button, the time will increase by one hour.
-U
p to 12 hours of reservation can be saved.
3. After setting up the start time, press the START/STOP
button on the HOM-BOT 2.0 or wait about five seconds.
When the timer setting is complete, a melody will sound,
and the timer indicator will remain on.
- If the timer is set, timer icon of a clock shape is
displayed on the status indicator lamp.
Tip
20
• When the set up time elapses, cleaning will start automatically.
•U
se the timer setting when the HOM-BOT 2.0 is attached to the home station. If the timer is
set while HOM-BOT 2.0 is away from the home station, the cleaning time can be shortened.
• To cancel the timer setting during the set up time, press the STOP button on the remote
control or the START/STOP button twice on the HOM-BOT 2.0.
• When operated the Smart-diagnosis mode during the reserved time, the reservation will be
cancelled.
MOP CLEANING (OPTION)
By attaching the ultra microfiber mop, you can
effectively use the HOM-BOT 2.0 to remove dust
from hard floors.
Ultra microfiber mop
Mop plate
When the mop plate is attached, the HOM-BOT 2.0
will not climb on to carpets or over thresholds, in
order to prevent transferring dirt from the mop.
For mop cleaning, mount the mop and mop plate to the HOM-BOT 2.0 according to the following instructions:
1. Attach the ultra microfiber mop to the Velcro
of the mop plate as shown in the figure.
※ To prevent the HOM-BOT 2.0 from
malfunctioning, attach the mop so that the
mop attaching guide will not be covered by
the mop.
Ultra microfiber mop
Mop fixing section
With mop attached
Mop plate
Ultra microfiber mop
Ultra microfiber mop
Bottom camera sensor
2. Accurately match up and insert the mop plate
fixing hook on the lower section of the
HOM-BOT 2.0 into the fixing groove of the
mop plate.
Fixing groove
Fixing hook
3. When you accurately match up and press the
mop plate to the rear side of the HOM-BOT
2.0, it will mount with a clicking sound.
※B
e careful to properly mount the mop plate,
or it can separate during cleaning.
Tip
“Click!”
• To avoid odors, wash any foreign material or dust off the mop after cleaning is complete.
• To avoid staining floors, do not use the ultra microfiber mop to clean when dirt is mixed with
liquids such as coffee or ink.
• To avoid damage to carpets from the Velcro or dirt transfer from the mop, do not clean the
carpet while the mop plate or mop is attached.
•K
eep the ultra microfiber mop dry. Do not use it on wet surfaces.
If there is moisture, it can interfere with the navigation.
• Smart-diagnosis mode cannot be operated with mop plate being attached..
21
LOCATION SEARCH FUNCTION
HOM-BOT 2.0 remembers its location while cleaning.
If the user moves the HOM-BOT 2.0 while it is operating, it will search its location with
the location search function so that it can continue from the previous location.
When the user removes any abnormal
condition of HOM-BOT 2.0 or moves the
location arbitrarily, the location search
function will activate.
Change location
When the location search function
is activated, the cleaning mode of
the status indicator will flash
1. L
ocate HOM-BOT 2.0 near the location where
HOM-BOT 2.0 was moved.
※ Location search is more effective when HOMBOT 2.0 is closer to the location where it was
moved.
※ If it goes out of diameter of 1 m from the
occurrence position, it becomes difficult to
search the position.
1m
1m
Location of incident
2. P
ress the START/STOP button on HOM-BOT 2.0 or START button on the remote controller.
HOM-BOT 2.0 will start the location search function along with an audio guide.
※ When
the location search is successfully completed, HOM-BOT 2.0 will continue to the cleaning from where
it was moved. If position search fails, it will start again from the beginning.
Checking current location.
Location of incident
Tip
22
• When the power is turned off after the location search function is set, the location search
function will be canceled.
• Location search is more effective when HOM-BOT 2.0 is closer to the location where it was
moved.
• The position search function will be cancelled if the remote is pressed to engage any other
function.
SMART-DIAGNOSIS MODE
HOM-BOT 2.0 can self-diagnose to determine its current status using smart diagnosis mode. If a problem
is found after the self-diagnosis, please contact LG Electronics service center
※ HOM-BOT 2.0 moves forward about 50 cm when smart diagnosis function is operated. Please clear out
stuff around home station within 1 m in order to not disturb the HOM-BOT 2.0.
1. P
lease turn on the main power switch on the bottom of the
HOM-BOT 2.0 and attach to home station.
※ Smart diagnosis function is operable only when HOM-BOT 2.0
is attached to home station
2. If smart diagnosis button is pressed for 3 seconds on the
HOM-BOT 2.0, smart diagnosis function will be started with a voice
message saying “HOM-BOT 2.0 smart diagnosis will be started. Please
step away and clear out stuff around home station within 1 m”
※ Smart diagnosis function will not be operated by pressing the charge
button on the remote controller.
※ Smart diagnosis mode will not be operated with mop plate being
attached.
3. If smart diagnosis is successfully complete, HOM-BOT 2.0
returns to the home station and informs the result of the
diagnosis in voice message. The voice message can be heard
again if smart diagnosis button is pressed after the first voice
message. When stop button is pressed, the smart diagnosis
will stop.
※ HOM-BOT 2.0 returns to the charging mode if no action is
made for 1 minute after the voice message.
※ HOM-BOT 2.0 will terminate smart diagnosis function,
not returning to the home station if a problem is found in
obstacle detecting sensor, ultrasonic sensor and Cliff detection sensor.
Tip
•P
lease be careful not to touch or disturb HOM-BOT 2.0 until the smart diagnosis is
complete. If the HOM-BOT 2.0 is disturbed, you can turn off and on the main power switch
to restart the smart diagnosis function.
•S
mart diagnosis function does not operate for the following cases below. Please check them
and try again.
- HOM-BOT 2.0 is away from the home station
- Battery is running low
- No dust bin exists
- Mop plate is attached
• Timer cleaning mode will be terminated if smart diagnosis starts. Please set up the timer
cleaning mode again when smart diagnosis is complete.
23
SMART-DIAGNOSIS MODE
Please refer to the table below to measure if voice message is heard after the smart diagnosis.
Voice message
Measures (Reference Page)
Starting smart diagnosis mode. Please step away and
remove any items within 1 meter.
Please step away and clear out stuff around home
station within 1 m until smart diagnosis is complete. (23p)
Unable to initiate smart diagnosis due to a low battery.
Please restart the smart diagnosis function after battery
is charged. (16p)
Smart Diagnosis mode will not operate with the mop plate
attached. Please try again after removing it.
Please start smart diagnosis again after removing the
mop plate.
HomBot will not charge due to infrared sensor error. Please try
smart diagnosis again after turning the main power switch on
the bottom of the HomBot 'Off' then 'On' again. If the problem
continues, please contact LG Electronics customer care.
If same message pops up even after the second smart
diagnosis, please contact LG Electronics service center.
HomBot will not charge due to ultrasonic sensor error. Please try
smart diagnosis again after turning the main power switch on
the bottom of the HomBot 'Off' then 'On' again. If the problem
continues, please contact LG Electronics customer care.
If same message pops up even after the second smart
diagnosis, please contact LG Electronics service center.
HomBot will not charge due to a problem with the cliff
sensors on bottom. Please wipe the sensors clean.
Please clean 3 cliff detection sensors on the bottom of
HOM-BOT 2.0. (28p)
Please clean the camera sensor on bottom right side.
Please wipe the lower camera sensor on the right
bottom of the unit.(28p)
A problem has been found on the Gyro Sensor. Please try smart
diagnosis again after turning the main power switch on the
bottom of the HomBot 'Off' then 'On' again. If the problem
continues, please contact LG Electronics customer care.
If same message pops up even after the second smart
diagnosis, please contact LG Electronics service center.
Please check for foreign material on the left wheel.
Please check dirt on the left wheel. (31p)
Please check for foreign material on the right wheel.
Please check dirt on the right wheel. (31p)
A problem has been found on the left wheel sensor. Please try
smart diagnosis again after turning the main power switch on
the bottom of the HomBot 'Off' then 'On' again. If the problem
continues, please contact LG Electronics customer care.
If same message pops up even after the second smart
diagnosis, please contact LG Electronics service center.
A problem has been found on the right wheel sensor. Please try
smart diagnosis again after turning the main power switch on
the bottom of the HomBot 'Off' then 'On' again. If the problem
continues, please contact LG Electronics customer care.
If same message pops up even after the second smart
diagnosis, please contact LG Electronics service center.
A problem has been found with the brush. Please check for
any foreign material.
Please check if foreign material is on the rotation brush.
(33p)
A problem has been found in the suction motor. Please try
smart diagnosis again after turning the main power switch on
the bottom of the HomBot 'Off' then 'On' again. If the problem
continues, please contact LG Electronics customer care.
If same message pops up even after the second smart
diagnosis, please contact LG Electronics service center.
A problem has been found in the acceleration sensor. Please try
smart diagnosis again after turning the main power switch on
the bottom of the HomBot 'Off' then 'On' again. If the problem
continues, please contact LG Electronics customer care.
If same message pops up even after the second smart
diagnosis, please contact LG Electronics service center.
Please, check the dust bin.
Please open the cover to check dust bin.(32p)
Smart diagnosis has failed to complete its diagnostics.
Please try smart diagnosis again after turning on and
Please try again after turning the main power switch on the off the main power switch on the bottom of HOM-BOT
bottom of the HomBot 'Off' then 'On' again.
2.0 and do not touch or disturb HOM-BOT 2.0 until
the smart diagnosis is complete.
24
CLEANING THE DUST BIN
If the dust bin is full, suction power can be weakened. Clean the dust bin before and after each cleaning
session. Clean the dust bin using the following sequence:
1. O
pen the dust bin cover by pressing the PUSH
button on the HOM-BOT 2.0.
2. G
rab the handle of the dust bin and pull it
upward.
3. S
eparate the HEPA filter and the inside sponge
filter by removing the HEPA filter
※ To clean the dust bin filter, refer to page 26.
4. L
ift the cover upward while pressing the
separation button on the dust bin.
※ Please use vacuum cleaner when cleaning the
filter.
(Be sure to fully dry the filter after washing it. It
may can affect inhalation or can make smell.)
5. E
mpty the dust bin and clean it with a cleaning
brush or under running water.
6. After cleaning with water, completely dry the dust
bin in a well-ventilated area out of direct sunlight.
7. When you have completed cleaning the dust bin,
close the dust bin lid and replace the sponge
filter and HEPA filter.
8. P
ut the dust bin into the HOM-BOT 2.0 and
close the dust bin cover.
Tip
• After cleaning, always mount the dust bin filters (HEPA filter, sponge filter) to the dust bin.
If they are not mounted, dust may enter the HOM-BOT 2.0 interior and cause product failure.
• After cleaning the dust bin, make sure to start the operation with the dust bin installed.
If operation is attempted without the dust bin, a voice message, “please check the dust bin”
will sound.
25
CLEANING THE DUST BIN FILTER
The dust bin filters are comprised of the HEPA filter and the sponge filter.
Clean the HEPA filter and the sponge filter according to the following sequence:
1. Separate the HEPA filter and the inside sponge
filter by removing the HEPA filter (as shown).
2. Carefully clean any fine dust off the HEPA filter and
the sponge filter with a vacuum cleaner or water.
※ When cleaning the filter with vacuum cleaner, be
careful not to suck the sponge filter with vacuum
cleaner.
3. After washing the HEPA filter and the sponge filter
with water, place them out of direct sunlight and allow
them to dry completely.
※ Please use vacuum cleaner when cleaning the filter.
(Be sure to fully dry the filter after washing it. It may
can affect inhalation or can make smell.)
4. M
ount the cleaned HEPA filter and sponge filter
into the dust bin according to the sequence
shown to the right. When assembling the filter,
the filter handle should face upward.
Tip
26
• In order to maintain the performance of the HOM-BOT 2.0, the HEPA filter should be
cleaned with a cleaning brush or vacuum cleaner at least once a week, and should be washed
under running water at least once a month.
CLEANING THE BRUSH
The brush, located on the bottom of the HOM-BOT 2.0, helps with the suction of foreign objects. Perform
the following steps to clean the brush:
※ Please make sure to remove the dust bin before turning over the main body.
Otherwise, the dust in the dust bin may fall out.
Lay a smooth cloth on the
floor. Turn the HOM-BOT 2.0
over and put the HOM-BOT
2.0 on the cloth. Turn off the
power switch before cleaning.
Separate the cover by pressing
the fixing hook and pulling
upward.
Wearing gloves turn the brush
until the separation groove of
the brush appears.
Separation
groove of
brush
Grab the brush and remove
by pulling it up.
Insert the fixing hook on the
opposite side of the brush
(marked with a rounded
rectangle) by matching it to
the separation groove of the
brush.
Clean the brush with a vacuum
cleaner, scissors, etc.
Insert the fixing guide in front
of the brush by matching it to
the fixing groove located on the
main unit.
Insert the fixing hook on the
side of the brush (marked with
the square) by matching it to
the fixing groove of the brush.
Close the cover by pressing
it down until you hear a click
from the fixing hook.
※ Be careful that the side
brush is not caught by the
cover.
27
CLEANING THE SENSOR/CHARGING TERMINAL
There are sensors on the HOM-BOT 2.0 that can detect obstacles, stairways
and the home station for charging the battery. In order to maintain the
performance of the HOM-BOT 2.0, regularly clean the sensors and charging
terminal as follows:
1. L
ay a smooth cloth on the floor, overturn the HOM-BOT 2.0 and put it on
the cloth.
※P
lease make sure to remove the dust bin before turning over the main body.
Otherwise, the dust in the dust bin may fall out.
2. Turn off the power switch on the bottom of the HOM-BOT 2.0. Injury can
be caused by the activation of the HOM-BOT 2.0 if the main power is not
turned off.
3. Use a smooth cloth or cleaning brush to wipe the dust off each sensor
and the charging terminal as described below.
Obstacle detection sensor
Receiving sensor of
remote controller
Camera sensor
Charging
terminal
Cliff detection sensor
Charging terminal
Lens
Bottom camera sensor
※ The device may move backwards while operating when the cliff sensor or bottom camera sensor is
contaminated. Please clean the sensor with soft brush or cleaning brush.
Tip
28
• Do not clean the HOM-BOT 2.0 by directly spraying it with water, thinner, benzene, etc.
•C
all the service center if the sensor or charging terminal is damaged. Sensor and terminal
damage can cause the product to malfunction.
CLEANING THE SIDE BRUSH
Foreign objects/materials such as hair can easily adhere to the side
brush. Remove such materials at least once a week.
If excessive amounts of foreign materials are stuck to the brush,
there is the risk of damage to the brushes.
If the floor is rough or skirting boards are frequently cleaned, the side brush may bend or become
damaged. In this case, use the following method to straighten the side brush.
1. The following procedure is helpful in restoring
deformed brushes.
2. Turn off the power supply by pressing the
START/STOP button on the HOM-BOT 2.0 for
two seconds.
3. P
lace the HOM-BOT 2.0 at the end of a table to
make cleaning the side brush easier. Make sure
that the HOM-BOT 2.0 is not in danger of falling.
4. S
oak the side brush in warm water.
5. P
ress down on the side brush for about ten
seconds so that it is completely submerged in
the water.
6. S
lowly wipe the side brush by sliding it through
your hand.
7. R
otate the side brush and repeat steps 4-6 for
each section of the brush.
8. U
se the side brush only after it has completely
dried.
How to change the side brush
1. Remove the screw and separate the side brush.
2. Exchange and re-assemble new side brushes.
29
CLEANING THE ULTRA MICROFIBER MOP (OPTION)
To avoid odors, dirt and dust should be washed off the mop after it is used for cleaning. Follow these
directions to wash the ultra microfiber mop:
1. Separate the ultra microfiber mop from the mop plate.
2. Carefully clean it with water.
3. U
se the mop only after allowing it to dry completely in a
sunny, well-ventilated area.
Tip
30
• To avoid product malfunction, only use the ultra microfiber mop provided with
the HOM-BOT 2.0.
• Additional microfiber mops can be purchased by visiting a nearby LG Electronics service
center.
TROUBLESHOOTING
When the voice, “Please check the wheels”, is announced.
If the unit becomes stuck or suspended and the wheels do not allow the unit to move, the voice,
“Please check the wheels”, will be announced.
• Is a wheel trapped in a floor gap, door, balcony, stairway, etc?
s Move the HOM-BOT 2.0 on to the flat floor.
• Is any foreign material wound around the wheel?
sL
ay a protective cloth on the floor, overturn the HOM-BOT 2.0, and put it on the cloth.
Remove foreign material by confirming the wheel.
※ Please make sure to remove the dust bin before turning over the main body.
Otherwise, the dust in the dust bin may fall out.
• Is the HOM-BOT 2.0 stuck?
s After removing the part that is stuck, place the HOM-BOT 2.0 on flat floor.
31
TROUBLESHOOTING
When the voice, “Please check the dust bin”, is announced
When an abnormality is detected with the dust bin, the voice,
“Please check the dust bin”, is announced.
• Is the dust bin fitted correctly?
sO
pen the dust bin cover, and if check if the dust bin is actually fitted.
The unit will not operate without the dust bin.
s If the dust bin cover is opened, close the cover before operating the unit.
When the voice, “Battery is low”, is announced.
When remaining amount of battery is almost nil, the voice, “Battery is low”, is generated.
• Initiate battery charging of HOM-BOT 2.0 by moving it to the home station.
s If HOM-BOT 2.0 is attached to the docking station, it will start the recharging with the recharging start
melody.
32
TROUBLESHOOTING
When the voice, “Please check the brush”, is announced
When the HOM-BOT 2.0 detects that the brush is not functioning properly, you will hear the message
“Please check the brush.”
Lay a protection cloth on the floor, overturn the HOM-BOT 2.0, and place it on the cloth.
※ Please make sure to remove the dust bin before turning over the main body.
Otherwise, the dust in the dust bin may fall out.
• The side brush is stuck.
sR
emove any foreign materials such as cables, thread or hair caught in the side brush or the brush.
s Confirm the correct assembly of the brush by checking the separation groove of the brush.
Separation
groove of brush
Proper assembly assures that the rotation of
the brush becomes smooth.
• The brush is making a loud, abnormal sound.
sR
emove the brush from the HOM-BOT 2.0 and remove any foreign material from the brush.
Separation
groove of brush
※ For a more detailed description of this process, refer to the instructions on page 27.
33
BEFORE YOU CALL FOR SERVICE
Confirm before reporting the failure of HOM-BOT 2.0.
Problem
34
Solutions (Reference page)
The HOM-BOT 2.0 will not
activate.
ƬƬ Confirm that the power switch is turned on. (Page 14)
ƬƬ Confirm that the battery has been charged. (Page 17)
Movements or travel path are
abnormal.
ƬƬ Carefully wipe the sensor with a smooth cloth. (Page 28)
ƬƬ If the ultra microfiber mop is attached, confirm that it is mounted
properly. (Page 21)
ƬƬ Turn on the power switch off and on.
Suction power becomes weak.
ƬƬ Check whether there is foreign material blocking the suction port.
(Page 27)
ƬƬ Empty the dust bin. (Page 25)
ƬƬ Clean the dust bin filter. (Page 26)
Noise becomes louder.
ƬƬ Confirm that the dust bin has been mounted properly.
ƬƬ Confirm that the dust bin filter has been mounted properly.
(Page 26)
ƬƬ Check whether foreign material is caught in the brush. (Page 27)
ƬƬ Please check if there is any tape, gum or other kind of foreign
materials are on the wheel.
The HOM-BOT 2.0 cannot
be activated with the remote
control.
ƬƬ Replace the remote control batteries. (Page 11)
ƬƬ Confirm that the control is within the coverage area of the main unit,
which is less than 3 m or 9.84 ft. (Page 11)
ƬƬ Check whether the main power switch on the bottom is turned on.
(Page 14)
The brush does not rotate.
ƬƬ Clean the brush. (Page 27)
ƬƬ Confirm that the brush has been mounted properly. (Page 27)
The HOM-BOT 2.0 will not
charge.
ƬƬ Remove objects around the home station. (Page 13)
ƬƬ Confirm that the power supply is connected to the home station.
(Page 13)
ƬƬ Wipe the charging terminal with a dry cloth.
ƬƬ Press the reset button on the back of the home station for
3 seconds while the HOM-BOT 2.0 is attached to the home station.
(Page 14)
Automatically starts
searching for home station.
Automatically turns
the power off.
HOM-BOT 2.0 will automatically return to the home station to recharge
when it's left uncharged or without cleaning order for more than 10
minutes.
The power supply cannot be
turned on.
Check that the power switch is turned on. (Page 14)
PRODUCT SPECIFICATIONS
Item/Model
LG HOM-BOT 2.0
VR6140LVM
External Dimensions
Φ 360 mm × 90 mm
Weight
3.2 kg
Power Consumption
18 W
Battery (Fully Charging)
DC 16.8 V
Traveling Velocity
350 mm/s
Use Time
Approx. 75 minutes
(Based on general wooden floor)
Charging Time
3 hours
Main Functions
Obstacle detection
Fall prevention
Timer cleaning
Error indication
Location search
Automatic / manual charging
Dry mop (Wiping)
Corner cleaning
Voice output
Map building
Spot cleaning
Spatial expansion cleaning
Zigzag cleaning
Smart-diagnosis
Item/Model
Home Station VR607
External Dimensions
245 mm × 193 mm × 132 mm
Rating
230 V~ 50 Hz
Output Voltage/Current
17.1 VDC / 1.1 A
Power Consumption
23 W
Item/Model
Battery
Type
Lithium Ion Polymer Battery
35
REFERENCE ITEMS
Open source software notice
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available
for download.
WARNING
Please be careful of fire, explosion, electric shock, or breakdown.
•D
o not charge this Battery Pack(Pack hereafter) with any other type of charger than the one originally
provided whit the charger.
• Do not damage the Pack in such ways as drop, crush, puncture, cut or short extemal contacts.
•D
o not attempt to disassembly the pack In any case. When the Pack is damaged or malfunctioning,
bring it to the service center.
• Do not place this pack near a heat source or do not dispose of in fire or water.
• Please keep the Pack away from damp or wet environment when the pack is charged.
• Please keep away from children, infant or pets.
Disposal of waste batteries/accumulators
1. When this crossed-out wheeled bin symbol is attached to batteries/accumulators of Your product it means they
are covered by European Directive 2006/06/EC.
2. This symbol may be combined with chemical symbols for mercury(Hg), cadmium(Cd) or lead(Pb) if the battery
Contains more that 0.0005% of mercury, 0.002% of cadmium or 0.004% of lead.
3. All batteries/accumulators should be disposed separately from the municipal waste stream via designated
collection facilities appointed by the government or the local authorities.
4. The correct disposal of Your old batteries/accumulators will help to prevent potential negative consequences for
the environment, animal and human health.
5. For more detailed information about disposal of Your old batteries/accumulators, please contact Your city office,
waste disposal service or the shop where You purchased the product.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the
European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the municipal waste stream via
designated collection facilities appointed by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment
and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office, waste
disposal service or the shop where you purchased the product.
36
MEMO
Made in Korea
Download PDF