LG | WD-1265FD | LG WD-1265FD Owner’s Manual

Washing
Machine
OWNER'S MANUAL
WD-1060F(H)D/1065F(H)D
WD-1260F(H)D/1265F(H)D
WD-1460F(H)D/1465F(H)D
Thank you for buying a
LG Fully Automatic Washing machine.
Please read your owner's manual carefully, it provides
on safe installation, use and maintenance.
instructions
Retain it for future reference.
Record the model and serial numbers of your
washing
mach
P
roduct Feature
Jumbo drum
40%
LG's
jumbo
drum
conventional
can
wash about 40%
machines. A
washing
more
bigger
load than
drum
improves
the wash
performance.
More economical
Intelligent
Wash
by Intelligent
System
Wash
System
detects the amount of load and water
temperature, and then determines the optimum
time to minimize energy and water
washing
Direct Drive
water level and
consumption.
System
The advanced Brushless DC motor rotates the Drum
without belt and
directly
pulley.
Child-Lock
Wash
The Child-Lock
Rinse
pressing
system has been used
any button to
Low noise
speed
change
control
to
prevent children from
the program
during operation.
system
the amount of load and balance, it
load to minimize the spinning noise level.
By sensing
evenly
distributes
Auto Restart
If the washing machine is turned off by a power failure, it will restart
automatically from the position it stopped at adjusting accordingly.
C
ontents
Warnings....................................................................................3
Specification
..............................................................................4
Installation..................................................................................5
Care before
washing................................................................11
Adding detergent
.....................................................................12
Function ...................................................................................13
How to
use
washer ..................................................................14
Maintenance ............................................................................20
Troubleshooting guide
Terms of
2
.............................................................23
Warranty ...................................................................26
arnings
W
READ ALL INSTRUCTIONS BEFORE USE
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
WARNING!
!
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock,
the
?
Do not install
be
?
?
or
store the washer where it will
?
exposed to the weather.
Do not
tamper with controls.
repair or replace any part of the washer
attempt any servicing unless specifically
instructions
or
published user-repair
instructions
?
that you understand and have the skills to carry
Keep the area underneath and around your
appliances free of combustible materials such
lint, paper, rags, chemicals, etc.
Close supervision is necessary if this
is used
by
or near
Do not wash
or
dry
articles that have been
or spotted with
explosive substances (such as
wax, oil, paint, gasoline, degreasers, drycleaning solvents, kerosene, etc.) which may
ignite or explode.
To avoid such a result, carefully follow the
garment manufacturer's wash and care
in, washed in, soaked in,
or
on,
with,
this or any other
Do not leave the washer door open.
An open door could entice children to
or
appliance
or
?
inside
?
Never reach into washer while it is
?
The
hang
can
try to
To minimize the
this
possibility of electric shock,
appliance from the power supply
or
disconnect the washer at the household
on
?
moving.
completely stopped.
laundry process
retardant of fabrics.
or
distribution
crawl inside the washer.
until the drum has
Do not slam the washer door closed
force the door open when locked. This could
result in damage to the washer.
as
unplug
play
appliance.
the door
?
children.
Do not allow children to
?
using
instructions.
out.
?
to persons when
combustible
recommended in the user-maintenance
?
injury
cleaned
Do not
or
or
washer, follow basic precautions, including the following:
Wait
reduce the flame
panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning.
Never attempt to operate this appliance if it is
damaged, malfunctioning, partially
disassembled, or has missing or broken parts,
including a damaged cord or plug.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This
grounded. In the event of malfunction or breakdown, grounding will reduce the risk
by providing a path of least resistance for electric current. This appliance is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.
Do not use an adapter or otherwise defeat the grounding plug.
appliance
must be
of electric shock
?
?
If you don't have the proper
WARNING :
outlet, consult
an
electrician.
Improper
connection of the equipment-grounding conductor can result in risk of electric
qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance if it does not fit the outlet, have a
proper outlet installed by a qualified electrician.
shock. Check with
a
-
3
S
pecification
Power
If the
plug
supply cord is damaged,
replaced by the
it must be
manufacturer
or its service agents
similarly qualified person in
Drawer
or a
(For detergent and
fabric softener)
order to avoid
Control
a
hazard.
panel
Drain hose
Door
Lower
cover
Drum
Leveling leg
Drain pump filter
Lower
Drain
cover
cap
plug
Name
Power
supply
:
Front
:
220-240V~,50Hz
600mm(W)
65kg
loading washing
Size
:
Weight
Wash capacity
:
:
Refer to the
Max. Watt
:
2100W
Spin speed
:
machine
600mm(D)
Rating
850mm(H)
label
No
Spin/400/600/800/1000[WD-1060F(H)D]
Spin/400/800/1000/1200[WD-1260F(H)D/WD-1265F(H)D]
No Spin/400/800/1000/1400[WD-1460F(H)D/WD-1465F(H)D]
:75
(10.7 /kg)
: 0.3-10kgf/
(30-1000kPa)
No
Water
consumption
Permissible water pressure
The appearance and
specifications
may be varied without notice to raise the units
Accessories
Inlet
4
hose(1EA)
Option
:
Hot/Cold(2EA)
Spanner
quality.
nstallation
I
Install
or
store where it will not be
exposed
to
temperatures below freezing
or
exposed
to the
weather.
Properly ground washer to conform with all governing codes and ordinances.
The base opening must not be obstructed by carpeting when the washing machine
carpeted floor.
In countries where there
vermin,
pay
all times.
particular
are areas
attention to
Any damage which may
appliance guarantee.
be
cause
is installed
on a
which may be subject to infestation by cockroaches or other
keeping the appliance and its surroundings in clean condition at
by
cockroaches
or
other vermin will not be covered
by
the
Transit bolts
The
appliance
is fitted with transit bolts to
Removing
prevent internal damage during transport.
transit bolts
1. To
prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove
the bolts
?
along
with the rubber
3. Take out the 4 bolts
along with the rubber
bungs by slightly twisting the bung. Keep
the 4 bolts and the spanner for future
use.
bungs.
If they are not removed, it may cause heavy
vibration, noise and malfunction.
?
Whenever the
appliance
is
transported,
the
transit bolts must be refitted.
cap
2. Unscrew the 4 bolts with
the spanner
4. Close the holes with the caps
supplied.
supplied.
5
nstallation
I
Installation
place requirement
Level floor
Drain Hose
Allowable
Washer
:
under entire washer is 1˚
slope
Power outlet
:
Must be within 1.5 meters of either side of location
of washer. Do not overload the outlet with
than
Laundry
one
Additional Clearance :
For wall, door and floor modeling is
Tub
approx.
2cm
more
appliance.
(10cm
: rear
Do not
place
/2cm:right
or
store
& left
required.
side)
laundry products
washer at any times.
They can damage the finish
or
on
top of
controls.
650
850
600
BS
Plug Safety Details (For
U.K.
User)
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN AND YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
This
appliance
Green and Yellow(Earth)
must be earthed
E
Brown(Live)
L
Blue(Neutral)
Fuse
N
Cord
grip
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
the terminals in your plug, proceed as follows:
The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the
identifying
letter E
or
by
the earth
symbol
or
coloured Green
or
Green and Yellow.
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N
or
The wire which is coloured Brown must be connected to the terminal which is marked with the letter L
If
a
13 amp
6
(BS 1363) plug
is
used, fit
a
13 amp BS 1362 fuse.
coloured Black.
or
coloured Red.
nstallation
I
Electrical connection
1. Do not
3.
extension cord
cord is
5. The
?
?
appliance
or
it must be
4. Connect the machine to
?
double
adapter.
supply
damaged,
replaced by the
or similarly qualified person in order to avoid a hazard.
Always unplug the machine and turn off the water supply
use an
2. If the
must be
an
manufacturer
after
so
that the
plug
is
easily
its service
agents
use.
earthed socket in accordance with current
positioned
or
wiring regulations.
accessible.
Repairs to the washing machine must only be carried out qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center
Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen
hoses may burst under pressure. The reliability of the electronic control unit may be impaired at
temperatures below freezing point.
If the appliance is delivered in the winter months and temperatures are below freezing : Store the
washing machine at room temperature for a few hours before putting it into operation.
Machine is to be connected to the water mains
sets and that old hose-sets should not be used.
Washing
Connecting
water
using
new
hose-
hose
supply
Water
supply pressure must be between
(0.3~10kgf/cm2)
30kPa and 1000kPa
Don't
strip or crossthread when connecting
Inlet hose to the valve.
If the water supply pressure is more than
1000kPa, a decompression device should be
installed.
?
Two rubber seals
are
supplied with
the
water inlet hoses these are in order to
prevent
?
Hose connector
Rubber seal
water leaks.
Check water tightness of washing
machine connections by turning the
completely
?
tap
on.
Periodically check the condition of the
replace the hose if necessary.
hose and
Hot water
?
tap
Cold
Cold
Hot(option)
Make sure that there is no kink
hose and that it is not crushed.
on
the
water
When your washer has two valves,
tap
?
?
The Inlet hose which has red connector is
for the hot water tap.
If the washer has two valves, the energy
is saved by using hot valve.
7
nstallation
I
Tap without
Normal
1. Unscrew the fixing
attach the tap.
screw
thread &
2.
to
screw
type inlet hose
Push the connector up till the
rubber
packing
with the
3.
is in
tap. Then
tight contact
tighten the 4
screws.
Tap without
Normal
1. Untighten the upper
thread &
connector
2.
touch
one
packing
contact with the
Upper
Rubber
Connector
Fixing
tighten
packing
screw
type inlet hose
Push the upper connector up till
the rubber
screw.
Middle
the 4
Rubber
connector
Push the water supply hose
vertically upwards so that the
rubber packing within in the
hose can adhere completely to
the tap and then tighten it by
screwing it to the right.
is in
3.
Connect the water
to the middle
tight
tap. Then
pushing
the
supply
hose
connector,
plate
down.
screws.
Upper
Connector
packing
Plate
Upper
?
In
case
large
the diameter of the
remove
Guide
the
Connector
tap is
Water
hose
Middle
guide plate.
connector
plate
?
Turn the middle connector not
to have water leaked.
Connector
?
Make
sure
that the rubber seal
is inside the hose connector.
?
To
supply
separate the
water
supply
hose from the middle connector
shut off the
inlet hose
plate
tap. Then pull the
down, pushing the
down.
Hose connector
Rubber seal
Used the horizontal
Horizontal
tap
tap
?
Your machine
comes
with
only
cold water connection.
?
Extension
tap
Make
sure
that there
not crushed.
Square tap
8
are no
kinks in the hose and that it is
nstallation
I
This
equipment
is not
designed
for maritime
use or
for
use
mobile installations such
as
caravans, aircraft etc.
Turn off the
stopcock if the machine is to be left for any length of time (e.g. holiday),
especially if there is no floor drain(gully) in the immediate vicinity.
When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the
door lock to prevent young children being trapped inside.
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk
of suffocation ! Keep all packaging well away from children
Installation of drain hose
ca.
ca.
145
100
cm
cm
?
max.10cm min.60cm
When
installing the drain hose sink,
it tightly with a string.
Proper securing of the drain hose will
protect the floor from damage due to
water leakage.
secure
ca.
105
cm
?
Laundry
ca.
100
tub
cm
Hose
ca.
145
Retainer
cm
Tie
max.
ca.
?
?
105
min.60cm max.10cm
cm
The drain hose should not be
higher than 100
Proper securing
cm
?
strap
max.
100cm
min. 60cm
min. 60cm
placed
above the floor.
of the drain hose will
protect the floor from damage due
water
100cm
to
leakage.
When the drain hose is too
long,
do
not force back into the washer. This
will
cause
abnormal noise.
9
I
nstallation
Level
adjustment
1.
Adjusting the washing machine level
properly prevents excessive noise and
vibration.
Install the
floor
the
appliance
on a
solid and level
surface, preferably in
a corner
of
room.
2. If the floor is uneven, adjust the leveling
feet as required. (do not insert pieces of
wood etc. under the
Make
sure
feet)
that all four feet
are
stable
and
resting on the floor and then check
that the appliance is perfectly level. (use
a spirit level)
Leveling leg
Higher
Lower
Leveling leg
Diagonal Check
When pushing down the edges of the
washing machine top plate diagonally,
machine should not
all.
(Please,
move
check both
the
up and down at
of two directions)
If machine rocks when pushing the machine
top plate diagonally, adjust the legs again.
10
C
before
are
Caring
before
washing
washing
1. Care Labels
Look for
garment
2.
label on your clothes. This will tell you about the fabric content of your
and how it should be washed.
a care
Sorting
To get the best results, Sort clothes into loads that can be washed with the same wash cycle.
Water temperature and spin speed and different fabrics need to be washed in different ways.
Always
transfer
sort dark colors from
soiled items with
Soil
3.
Caring
before
colors and whites. Wash
separately as dye and lint
possible, do not wash heavily
one.
(Heavy, Normal, Light)
(White, Lights, Darks)
(Lint producers, Collectors)
Color
Lint
pale
discoloration of white etc. If
causing
lightly soiled
can occur
Separate clothes according to amount of soil.
Separate white fabrics from colored fabrics.
Wash lint producers and lint collectors
separately.
loading
Combine large and small items in a load. Load large items first. Large items should not be more
than half the total wash load.
Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.
?
Check all
that
pockets to
make
sure
empty. Items such
nails, hair clip, matches, pens,
they
are
coins and
keys
can
damage
as
both
your washer and your clothes.
?
Close
zippers,
make
sure
snag
?
on
hooks and
little
to
other clothes.
Pre treat dirt and stains
a
strings
that these items don't
detergent
by brushing
dissolved in water
onto stains like collars and cuffs to
help
shift dirt.
11
dding detergent
A
Adding detergent
1. The
Dispenser
and fabric softener
3. Detergent dosage
Drawer
?
The
detergent should be used according to
of the detergent manufacture.
the
instruction
max
?
If too
much
detergent is
used more than the
recommended amount, too many suds can
occur and this will decrease the washing result
heavy load to the
malfunction)
or cause
?
Use powder
loading
?
Main wash
only
U
?
(Causing
a
detergent only for the front
washer.
Detergent
for water
?PreWash+MainWashU
motor.
usage may need to be
temperature,
water
adjusted
hardness,
size and soil level of the load. For best
2.
results, avoid oversudsing.
Adding Fabric Softener
(
)
MAX
MAX
125 ml
125ml
Tips
Full load
Part load
?
Do not exceed the maximum fill line.
Overfilling
can cause
clothes.
Do not leave the fabric softener in the
Softener will
during
?
automatically
cycle.
2
days.
be added
the last rinse
Do not open the drawer when water is
supplied.
?
Solvents(benzene, etc)
are
not
allowable.
NOTE
Do not pour fabric softener
on the cloths
directly
12
:
3/4 of the normal amount.
Minimum load
?
:
1/2 of full load.
Detergent is flushed from the dispenser
beginning of the cycle.
the
detergent drawer for more than
(Fabric softener could harden)
?
to
early dispensing
of the fabric softener which could stain
?
according
:
manufacturer's recommendation.
at
F
unction
Recommended
courses
Fabric
according
Proper
Temp.
(Option)
Program
Type
to the
laundry type
Maximum
Washing
(Option)
Time
Water
Energy
in
in
in
Load
Liter
kWh
Minutes
Rating
75
0.47
119
Less than
55
0.39
92
55
0.15
65
55
0.05
55
Coloureds Color fast garments
(shirts, night
40˚C
dresses,
(Cold, 30˚C, Main(+Pre)
60˚C)
pajamas...)and
lightly soiled white
cotton
(underwear...)
40˚C
Synthetic Polyamide, Acrylic,
(Cold, 30˚C, Main(+Pre)
Polyester
60˚C)
Delicate
Wool
Rapid
laundry
easily damaged
(silk, curtains...)
Machine washable
Cold
(30˚C,
40˚C)
Laundry type is the
in Coloureds
and
Synthetic.
kg
Less than
Main
(30˚C,
40˚C)
woolens with pure
new wool only
same
Whites
Cold
Delicate
4.0
3.0
kg
Less than
Main
2.0
kg
Cold
Main
Rating
55
0.10
54
Main(+Pre)
Rating
90
2.74
162
Main(+Pre)
Rating
70
1.13
178
(30˚C,
40˚C)
First check if
laundry is machine
washable.
(white cotton,
95˚C
(40˚C,
60˚C)
linen
towels and
sheets...)
WhitesEco
Laundry type is the
in Whites.
same
Pre Wash
Water
:
For
heavily
Temperature
60˚C
(40˚C)
:
soiled and
protein-stained
Select the water
garment
items.
temperature
manufacture's
care
to the wash
label
or
cycles. Always
follow
instructions when
laundering.
13
ow to use
H
washer
Synthetic
1000
Coloureds
Whites-Eco
Time
Delicate
Whites
Rapid
Start/Pause
1. Coloureds
automatically
selected upon power
Rinse Hold
600
40
400
30
Main Wash
Normal
Wash
Rinse
2. Manual
?
?
Press the Start/Pause button.
?
Initial condition
Wash
:
Main wash
-
Rinse
:
3 times
Water temperature
:
40˚C
Program : Coloureds
14
Spin
Cold
Temp.
Selecting
Press the Power button to start.
Select the conditions which you want to
use, by pressing each button.
conditions, please
refer to the page15~page19
?
-
Spin
For selecting the each
-Spin:800rpm
-
No
on.
Press the Power button to start.
-
60
Super
Time Left
?
?
800
Pre Wash
Wool
e
95˚C
Delay
Press the Start/Pause button.
H
ow to use
(1)
(1)
(2)
(3)
Button
Dial
:
washer
(2)
(3)
Power
(4)
(5)
(6)
Program
:
Button
:
(4)
Start/Pause
(5)
Button
(6)
:
(7)
(8)
Wash
(7)
(8)
(9)
Child lock
Button
:
Rinse
Power
(9)
Button
:
Time
Button
:
Spin
Button
:
Water
Delay
Temp.
Program
?
7 programs
are
available
according
to the
laundry type.
-
-
1. Power
-
-
?
?
Press the Power button to turn power
and off.
To cancel the Time
Power button
Delay function,
should be pressed.
on
the
-
Coloureds
Synthetic
Delicate
Wool
Rapid
-
Whites
-
Whites-Eco
?
(Program)
Lamp will light
up to indicate selected
program.
2. Initial
?
When the Power button is
washer is
1.
Program
ready
pressed,
the
?
for Coloureds program.
as follows.
-
So, if you
want to advance into the
washing cycle without changing the
program, just push Start/Pause button
and then the washer will proceed.
Initial program
-
Coloureds Program / Main wash /
Normal Rinse/800 rpm / 40˚C
When Start/Pause button is
Coloureds program is
selected.
And the other initial conditions
?
Program
the
By turning
pressed,
automatically
Program dial,
the program is
selected in order of "Coloureds
Synthetic
Whites
U
U
Delicate
Wool
U
the
U
U
Rapid
U
Whites-Eco".
Regarding to the laundry type for each program
Please refer to the page13.
2. Course
-
Whites
-
-
Whites-Eco
-
-
Coloureds
-
-
Synthetic
Delicate
Wool
Rapid
15
ow to use
H
washer
Start/Pause
Child lock
If you choose to lock the buttons on the
control assembly to prevent tampering, this
1. Start
?
function may be selected.
This Start/Pause button is used to start
wash
cycle
pause the wash
or
cycle.
1. Child lock
2. Pause
?
?
If
temporary stop of wash cycle is needed,
?
When in Pause, the power is turned off
automatically after 4 minutes.
?
NB. The door will not open before 1 to 2
minutes when Pause is selected,
Child lock
can
be set
at the end of the wash
Time Left
?
cycle.
?
Wash
By pressing
?
button,
can
by pressing and holding the
simultaneously.
Wash button and Rinse button
press Start/Pause button.
or
Rinse
Wash
Start/Pause
When child lock is set, all buttons
are
press and hold the
system,
Wash and Rinse button
simultaneously again.
the Wash
the wash
type
Time Left
be selected.
-
Main Wash
-
Pre
?
+
inoperable.
To deactivate Child lock
Main Wash
To
change to the desired
program, whilst in child
lock mode.
1. Press and hold both Wash and Rinse
1. Main Wash
once
together
again.
2. Press the Start/Pause button.
?
Main Wash
normally
2. Pre
course
soiled
+
is available for
lightly
laundry.
or
3. Select the desired program and press the
Start/Pause button again.
Main Wash
Change
the desired
?
If the
laundry
Wash"
?
course
is
heavily soiled,
"Pre
Whites-Eco and
Coloureds, Whites,
Synthetic program.
required lamp
identification.
16
program
Main
is effective.
Pre Wash is available in
The
+
will
light up for
?
The child lock
can
be set at any time and it is
automatically canceled when operational
occur.
errors
Also Child lock works when power is off.
washer
ow to use
H
Rinse
?
Rinse Hold
By pressing
button,
Super
can
Normal
-
-
-
-
Rinse
Time
the Rinse
the Rinse
type
be selected.
Time Left
Super
Normal
+
Rinse Hold
Super + Rinse Hold
1. Time
performs 3 Rinses
-
-
Turn
?
Super
?
Use the
+
1
How to set "Time
-
more
Super
rinse time.
-
rinse when additional
rinsing is desired to remove
and detergent soiled loads.
excess
the water
tap.
laundry and close the door.
Place the detergent and fabric softener
-
Normal
on
Load
in
the drawer.
Rapid / Wool / Delicate performs 2 Rinses
?
"Time
Delay"
Coloureds / Whites / Whites-Eco / Synthetic
2.
Delay
Preparing washing before starting
-
?
Time Left
Normal
1. Normal
?
Delay
Delay"
Press Power button.
Turn the
Programme
dial to select
the program you require.
Press Time Delay button and set the
desired time.
dirt
-
Press the Start/Pause button.
(":" blinks.)
3. Rinse Hold
?
?
Is selected
the Rinse button
by pressing
repeatedly this function leaves clothes in
the washer; suspended in the water after
a rinse without entering into spin.
To drain and spin, press the Rinse button
or
lamp.
The required lamp
identification.
Delay button is pressed, "3:00" is
displayed. The maximum delayed time is
19:00 hours and the minimum time is 3:00
hours.
?
Start/Pause button to turn off the rinse
hold
If Time
?
Each
pressing of the
delay by one hour.
To cancel the time
button advances time
delay,
press the Power
button.
will light up for
?
Time
present
or
?
'expected time' from the
completion of washing cycle
process (Wash, Rinse, Spin).
Delay
is
to the
selected
According to
the condition
temperature, the
washing time
delayed
of water supply and
time and the actual
may vary.
17
ow to use
H
washer
2. No
Spin
1000
1200
1400
800
1000
1000
600
800
800
400
400
400
No
No
Spin
No
Spin
?
spin
If no spin is selected,
draining water.
The
required lamp
identification.
will
the washer
light up for
Spin
Water
Spin
Spin
Spin
[WD-1060F(H)D]
?
[WD-1260F(H)D/
1265F(H)D]
By pressing the Spin button,
can
[WD-1460F(H)D/
1465F(H)D]
the spin speed
[WD-1260F(H)D/
1265F(H)D]
No Spin
No
-
400
-
400
-
400
-
600
-
800
-
800
-
800
-
1000
-
1000
-
1000
-
1200
-
1400
1.
Spin
-
40
program
as
is available
-
Cold
according
to the
(1200)U (1400)U
SpinU
400U
(600)
-
-
Whites/Whites-Eco
800U 1000U
(1200)U (1400)U
No
SpinU
400U
(600)
-
-
Rapid
800U 1000U
(1200)U (1400)U
No
SpinU
400U
(600)
-
-
Synthetic
800U 1000U No
-
SpinU
400U
Delicate
400U No SpinU 600U 800
400U No SpinU 800
(600)
[WD-1060F(H)D]
[WD-1260F(H)D/1265F(H)D/1460F(H)D/1465F(H)D]
-
Wool
400U No
18
SpinU (600)U
800U 1000
Water
Temperature
temperature
below
follows.
No
Cold
-30˚C/40˚C/60˚C/95˚C
1. Water
Coloureds
800U 1000U
Temp
Temp.
-
-
the
-
Spin selection
Spin speed
By pressing
selected.
30
?
?
Temp.
button, the water
temperature can be
60
[WD-1460F(H)D/
1465F(H)D]
No Spin
-
?
95˚C
be chosen.
[WD-1060F(H)D]
stops after
according
can
be selected
Coloureds &
Synthetic
40˚C
60˚C
U
Cold
Whites
95˚C U 40˚C
U
60˚C
U
as
to the program.
U
30˚C
Whites-Eco
60˚C U 40˚C
& Wool & Delicate
Rapid
Cold
U
30˚C
U
40˚C
The
required temperature lamp
identification.
For the
more
to the page13.
detailed
will light up for
information, please refer
H
washer
ow to use
3.
Display
?
Completion of washing
When
washing cycle is completed,
is displayed on the "Multi
display".
"
"
Time Left
1.
?
Special function display
When child lock is selected, the
is displayed.
"
"
?
4. Time left
?
When time
the
delay is selected, it shows
remaining times to finish the selected
During washing cycle, the remaining
washing time is displayed.
Recommended program
?
program.
-
2. Self
-
diagnose display
-
?
If the washer encounters
operation,
displayed.
"
"
:
"
"
:
"
"
"
"
"
"
"
"
"
"
"
"
"
a
fault
during
-
the associated fault will be
-
-
Water pressure
Problem of
sensing
overfilling
by
manufacturer.
error
-
Coloureds
:
around 1 hour and 59 minutes
Synthetic
:
around 1 hour and 32 minutes
Delicate
:
around 1 hour and 5 minutes
Wool
:
around 55 minutes
Rapid
:
around 54 minutes
Whites
:
around 2 hours and 42 minutes
Whites-Eco : around 2 hours and 58 minutes
water
:
Door is not closed
:
Over load in motor
:
Over load in motor
washing time may vary by the
laundry, water pressure,
water temperature and other washing
:
Water inlet trouble
conditions.
:
Drainage
:
Unbalanced load
"
:
?
The
amount of
trouble
Water temperature trouble
?
If
an
unbalanced load is detected
the suds
if
or
removing program operates,
the wash time may be extended.
(Max. increasing time is 45minutes.)
If these error letters are displayed, please
refer to the troubleshooting page23 and
follow the guide.
19
aintenance
M
Before
the washer interior,
cleaning
unplug the electrical
power cord to avoid electrical shock to
avoid electrical shock hazards.
When
disposing
lock to
prevent
of the
appliance, cut off the mains cable,
being trapped inside.
and
destroy the plug
Disable the door
young children
The water inlet filter
"
-"
error
detergent
-
message will blink
If your water is very hard
become
on
the control
panel
when water does not enter the
drawer.
clogged.
a good
It is therefore
or
contains traces of lime
deposit,
the water inlet filter may
idea to clean it from time to time.
2. Unscrew the
1. Turn off the
water
water inlet
tap.
hose.
3. Clean the
filter
4.
using
Tighten
up
the inlet
a
hard bristle
hose.
brush.
The drain pump filter
The drain filter collects threads and small
Check
!
regularly
CAUTION
that the filter is clean to
First drain
using
left in the
smooth
laundry.
running of your
machine.
the drain hose and then open the pump filter to
whatever any threads
Be careful when
objects
ensure
or
objects.
draining if the water is hot.
cleaning the drain pump, carrying
Allow the water to cool down before
emptying
1.
or
opening
Open the lower cover
cap( )byusinga
the door in
2.
an
out emergency
emergency.
Unplug the drain plug ( ),
allowing the water to flow out.
3. Remove out any
At
foreign material
( ). After
the pump filter ( )
from the pump filter
coin. Turn the drain
this time
plug( )topullout
water
the hose.
water does not flow any more, turn
plug (
the pump filter
close the lower
20
use a
flowing
remove
vessel to
on
prevent
to the floor. When
( )
open to the left.
cleaning,
turn
clockwise and insert the drain
)to the original place.
cover
cap.
aintenance
M
Dispenser
After
a
while
drawer
detergents
and fabric softeners leave
deposit
It should be cleaned from time to time with
?
If necessary it can be removed completely from the machine
downward and by pulling it out.
?
To facilitate
cleaning,
the upper
a
jet
of
a
?
running
in the drawer.
water.
by pressing
part of the fabric softener compartment
the catch
can
be removed.
max
max
The drawer
Detergent can
be cleaned
?
also accumulate inside the
cycle
The
without
washing
If you live in
seen
with
occasionally
Once you have finished
rinse
?
recess
a
recess
cleaning, replace
the drawer and
run a
laundry.
drum
hard water area, limescale may
and thus not
which should
old toothbrush.
an
easily
continuously
build up in
places where
it cannot be
removed.
Over time the build up of scale
clogs appliances,
and if it is not
kept
in check these may have to be
replaced.
?
Although the washing drum is made of Stainless steel, specks of rust can
articles (paper clips, safety pins) which have been left in the drum.
?
The
?
washing
If you
use
be caused
by
small metal
drum should be cleaned from time to time.
descaling agents, dyes
or
bleaches, make
sure
they
are
suitable for
washing
machine
use.
Descaler may contain chemicals that may
Remove any
Never
use
spots with
a
stainless steel
damage part
of your
washing
machine.
cleaning agent.
steel wool.
21
aintenance
M
Cleaning
your washer
1. Exterior
of your washer
can
extend its life.
The outside of the machine
can
be cleaned with
Proper
care
household
detergent.
off any
Immediately wipe
not to hit surface with
Try
water and a neutral non abrasive
warm
IMPORTANT: Do not
spills. Wipe
with
damp cloth.
sharp objects.
methylated spirits,
use
diluents
or
similar
products.
2. Interior
Dry
around the washer door
Run washer
through
a
opening, flexible gasket and
complete cycle using hot water.
Repeat
process if necessary.
NOTE
Remove hard water
deposits using only
door
glass.
cleaners labeled
as
washer safe.
Cold condition
If the washer is stored in
temperatures,
an area
1. Turn off water
Plug
4. Add
freezing
may
occur or
prevent damage
moved in
freezing
to the washer:
supply tap.
2. Disconnect hoses from water
3.
where
follow these instructions to
electrical cord into
1gallon(3.8L)
a
supply
and drain water from hoses.
properly grounded
of nontoxic recreational
electrical outlet.
vehicle(RV)
antifreeze into
an
empty wash drum.
Close the door.
5. Set
spin cycle
and let washer
spin
Not all of the RV antifreeze will be
6.
Unplug
electrical power
7. Remove
9. To
remove
through
22
a
an
expelled.
cord, dry the drum interior, and close the door.
dispenser drawer,
8. Store washer in
for 1minute to drain out all water.
drain and
dry
excessive water from the
upright position.
antifreeze from washer after
storage,
complete cycle using detergent.
run
empty washer
Do not add wash load.
compartments.
roubleshooting guide
T
This washing machine is
equipped with automatic safety functions which detect and diagnose faults at an
appropriately.
When the machine does not function properly or does not function at all, check the following points before
you contact your service provider.
early stage and
react
Possible Cause
Symptom
Rattling and
clanking noise
?
Solution
Foreign objects such as coins
safety pins maybe in drum or
or
Stop washer and
check drum
and drain filter.
If noise continues after washer
pump.
is restarted, call your authorized
service centre.
Thumping
Vibrating
sound
noise
?
?
a
Heavy wash loads may produce
thumping sound. This is usually
probably
normal.
redistribute wash load.
Have all the transit bolts and
packing
?
If not removed
been removed?
Are all the feet
the
If sound continues, washer is
out of balance. Stop and
during
installation, refer to Installation guide
resting firmly
on
for
removing
transit bolts.
Wash load may be unevenly
distributed in drum.
ground?
Stop washer and
rearrange wash
load.
Water leaks.
?
Fill hoses
at
?
tap
or
or
drain hose
are
loose
Check and
tighten
hose connections.
washer.
House drain
pipes
are
clogged.
Unclog
drain
pipe.
Contact
plumber
if necessary.
Too much
detergent or unsuitable
detergent may cause excessive
foaming which may result in water
Oversudsing
leaks.
Water does not enter
washer
or
?
it enters
slowly
Water
supply
it not
adequate
in
Check another
tap in the house.
area.
?
Water
?
Water inlet
?
The filter of the inlet
supply tap
completely open.
is not
hose(s)
are
Fully
kinked.
hose(s)
are
open tap.
Straighten hose(s).
Check the filter of the inlet
hose(s).
clogged.
Water in the washer
does not drain
drains
slowly.
?
Drain hose is kinked
?
The drain filter is
or
clogged.
Clean and
straighten
the drain hose.
or
clogged.
Clean the drain filter.
23
roubleshooting guide
T
Possible Cause
Symptom
Washer does not start
?
Electrical power cord may not
plugged in or connection
be
Solution
Make
plug
sure
fits
tightly
in wall
outlet.
may be loose.
?
House fuse blown, circuit
Reset circuit breaker
breaker
Do not increase fuse
tripped,or
a
power
outage has occurred.
If
problem
is
it corrected
?
Water
supply tap
is not turned
Turn
on
a
by
water
replace
capacity.
or
fuse.
circuit overload, have
a qualified electrician.
supply tap.
on.
Washer won't
spin
Check that the door is
shut.
firmly
Close the door and press the
Start/Pause button. After pressing
the Start/Pause button, it may take
a few moments before the clothes
washer
begins to spin. The door
spin can be
must lock before
achieved.
Door does not open
Once started, the door can not be
for safety reasons.
opened
Wait
one or
two minutes before
opening the door to give the electric
locking mechanism time to release.
Wash
cycle
delayed
time
The
washing time may vary by the
laundry, water
amount of
pressure, water temperature and
other using conditions.
If the imbalance is detected
suds
or
if the
program works, the
wash time shall be increased.
24
removing
roubleshooting guide
TSymptom
Possible Cause
?
Water
?
Water
?
?
Solution
supply is not adequate in area
supply taps are not completely
open.
Water inlet
hose(s)
are
The filter of the inlet
Fully open tap.
Straighten hose(s).
kinked.
hose(s)
Check another tap in the house.
Check the filter of the inlet
are
hose(s).
clogged.
?
Drain hose is kinked
Clean and
?
The drain filter is
Clean the drain filter.
?
Load is too small.
Add 1
?
Load is out of balance.
balance the load.
?
The
has
an
unbalance
detection and correction
system.
individual
are
heavy
articles
If
or
straighten
the drain hose.
2 similar items to
Rearrange
spinning
help
load to allow proper
loaded
etc.), this
system may stop spinning or even
interrupt the spin cycle altogether.
If the laundry is still too wet at the end
of the cycle, add smaller articles of
laundry to balance the load and repeat
the spin cycle.
(ex.
?
appliance
or clogged.
clogged.
bath mat, both robe,
?
Is the door
Close the door.
opened?
If
"
"is not released, call for service.
Unplug the
power
plug
and call for
service.
?
Water overfills due to the
faulty water
valve.
Close the water tap.
Unplug the power
Call for service.
?
Water level
?
Over load in motor.
?
Over load in motor.
sensor
plug.
has malfunctioned.
25
of
erms
T
Warranty
What Is Not Covered:
?
?
?
?
Service
to your home to teach you how to use the
trips
If the
product
rating plate.
is connected to any
voltage
product.
other than that shown
the
Act of God.
If the fault is caused
by accident, neglect, misuse
If the fault is caused
by factors other than normal domestic
or
on
use or use
in
accordance with the owner's manual.
?
?
?
Provide instruction
on use
If the fault is caused
Noise
or
product
or
change
by pests for example,
Correcting
or
the set-up of the
product.
rats or cockroaches etc..
vibration that is considered normal for
sound, spin sound,
?
of
example
water drain
warming beeps.
the installation for
example, levelling
the
of
product, adjustment
drain.
?
?
?
?
?
Normal maintenance which recommended
owner's manual.
foreign objects / substances from the machine, including the
pump and inlet hose filter for example, grit, nails, bra wires, buttons etc.
Replace
fuses in
or
correct house
Correction of unauthorized
Incidental
possible
?
by the
Removal of
If this
or
wiring
or
correct house
plumbing.
repairs.
consequential damage to personal property
appliance.
caused
by
defects with this
product
is used for commercial purpose, it is not warranted.
(Example : Public places
center, dormitory)
such
as
public bathroom, lodging house, training
If the
product is installed outside the normal service area, any cost of
transportation involved in the repair of the product, or the replacement
defective part, shall be borne by the owner.
26
of
a
M
emo
27
P/No.: 3828ER3005L
Download PDF

advertising