LG | WD-14370RD | LG WD-14375RD Owner’s Manual

P/No.: MFL30138487
WD-14370RD
WD-14375RD
roduct Feature
P
Direct Drive System
The advanced Brushless DC motor directly drives the drum without
belt and pulley.
Water Circulation
Spray detergent solution and water onto the load continuously.
Clothes are soaked more quickly and thoroughly during wash cycle.
The detergent suds can be removed more easily by the water shower during rinse
cycle. The water circulation system uses both water and detergent more efficiently.
Built-in Heater
Internal heater automatically heats the water to the best temperature on selected
cycles.
Child Lock
The Child lock prevents children from pressing any button to change the settings
during operation.
More economical by Intelligent Wash System
Intelligent Wash System detects the amount of load and water temperature, and then
determines the optimum water level and washing time to minimize energy and water
consumption.
Low noise speed control system
By sensing the amount of load and balance, it evenly distributes load to minimize the
spinning noise level.
Safety device (Aqua lock)
Aqua lock System is designed for detecting water leak during operation to prevent
water from flooding over the floor.
Steam Washing and Refresh
Steam Washing features upgraded washing performance with low energy
consumption. Refresh cycle reduces wrinkles from dry clothes.
Automatic Wash Load Detection
Automatically detects the load and optimizes the washing time.
추가선택, 예약,
C
2
ontents
Warnings ....................................................................................................................3
Specification ................................................................................................................5
Installation ...................................................................................................................6
Care before washing .................................................................................................12
Adding detergent .......................................................................................................13
Function ..................................................................................................................15
How to use washer ....................................................................................................16
Maintenance ..............................................................................................................26
Troubleshooting guide ...............................................................................................30
Terms of Warranty.....................................................................................................33
W arnings
READ ALL INSTRUCTIONS BEFORE USE
!
WARNING!
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock, or injury to persons when using
the washer, follow basic precautions, including the following:
• Do not install or store the washer where it will
be exposed to the weather.
• Do not tamper with controls.
• Do not repair or replace any part of the washer
or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or published user-repair instructions
that you understand and have the skills to carry
out.
• Keep the area underneath and around your
appliances free of combustible materials such as
lint, paper, rags, chemicals, etc.
• Close supervision is necessary if this appliance
is used by or near children or infirm persons.
Do not allow them to play on, with, or inside this
or any other appliance.
• Keep washer away from fire.
• Do not leave the washer door open.
An open door could entice children to hang on
the door or crawl inside the washer.
• Never reach into washer while it is moving. Wait
until the drum has completely stopped.
• The laundry process can reduce the flame
retardant of fabrics.
• Do not wash or dry articles that have been
cleaned in, washed in, soaked in, or spotted with
combustible or explosive substances (such as
wax, oil, paint, gasoline, degreasers, dry
cleaning solvents, kerosene, etc.) which may
ignite or explode. Oil may remain in the tub after
a whole cycle resulting in fire during drying. So,
do not load oiled clothes.
• To avoid such a result, carefully follow the
garment manufacturer’s wash and care
instructions.
• Do not slam the washer door closed or try to
force the door open when locked. This could
result in damage to the washer.
• To minimize the possibility of electric shock,
unplug this appliance from the power supply or
disconnect the washer at the household
distribution panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning.
• Never attempt to operate this appliance if it is
damaged, malfunctioning, partially
disassembled, or has missing or broken parts,
including a damaged cord or plug.
• dryer is intend only for drying textile material in
water.
• If the washer has been exposed to water, call an
authorized service provider to avoid any risk of
fire or electric shock.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance for electric current. This appliance is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.
• Do not use an adapter or otherwise defeat the grounding plug.
• If you don’t have the proper outlet, consult an electrician.
WARNING
:
Improper connection of the equipment-grounding conductor can result in risk of electric
shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a
proper outlet installed by a qualified electrician.
3
W arnings
To minimize the risk of fire in a tumble dryer, the following should be observed:
• Items that have been spotted or soaked with vegetable or cooking oil constitute a fire
hazard and should not be placed in a tumble dryer.
Oil-affected items can ignite spontaneously, especially when exposed to heat
sources Such as in a tumble dryer. The items become warm, causing an oxidation
reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can
become hot enough to catch fire. Piling, stacking or storing oil-affected items can
prevent heat from escaping and so create a fire hazard.
If it is unavoidable that fabrics that contain vegetable or cooking oil or have been
contaminated by hair care products be placed in a tumble dryer they should first be
washed in hot water with extra detergent-this will reduce, but not eliminate, the
hazard. Washed in hot water with extra detergent-this will reduce, but not
eliminate, the hazard. The ‘cool down’ cycle of tumble dryers should be used to
reduce the temperature of the items. They should not be removed from the tumble
dryer or piled or stacked while hot.
• Items that have been previously cleaned in, washed in, soaked in or spotted with
petrol/gasoline, dry-cleaning solvents or other flammable or explosive substances
should not be placed in a tumble dryer.
Highly flammable substances commonly used in domestic environments include
acetone, denatured alcohol, petrol/gasoline, kerosene, spot removers (some
brands), turpentine, waxes and was removers.
• Items containing foam rubber (also known as latex foam) or similarly testured
rubber. like materials should not be dried in a tumble dryer on a heat setting.
Foam rubber materials can, when heated, produce fire by spontaneous combustion.
• Fabric softeners or similar products should not be used in a tumble dryer to eliminate
the effects of static electricity unless this practice is specifically recommended by the
manufacturer of the fabric softener or product.
• Undergarments that contain metal reinforcements should not be placed in a tumble
dryer.
Damage to the tumble dryer can result if metal reinforcements come loose during
drying. When available a drying rack could be used for such items.
• Plastic articles such as shower caps or babies waterproof napkin covers should not
be placed in a tumble dryer.
• Rubber-backed articles, clothes fitted with foam rubber pads, pillows, galoshes and
rubber-coated tennis shoes should not be placed in a tumble dryer.
4
S
pecification
Drawer
Time Left
1:42
20%
Washing
Rinse
60°C
3
Temp.
Name
: Front loading washing machine
Power supply
: 220 - 240V~, 50Hz
Size
: 600mm(W)×645mm(D)×850mm(H)
Weight
: 66kg
Wash capacity/Max. Watt
: 9kg(2100W)
Dry capacity/Max. Watt
: 5kg(1500W)
Spin speed
Water consumption
: No Spin/400/800/1000/1400
: 67ℓ(7.4ℓ/kg)
Permissible water pressure
: 4.5 ~ 114 PSI (30 ~ 800 kPa)
The external hot water supply MUST NOT exceed 70 deg C
Permissible cold water temperature : 4-25˚C
No further backflow protection required for connection to the water supply.
❋ The appearance and specifications may be varied without notice to lmprove the units quality.
❋ Specifications subject to change by manufacturer.
❋ The appearance and specifications may be varied without notice to raise the units quality.
Accessories
Inlet hose(1EA)
Option : Hot/Cold(2EA)
Spanner
5
I
nstallation
Install or store where it will not be exposed to temperature below freezing or exposed to the
weather.
Properly ground washer to conform with all governing codes and ordinances.
The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
In countries where there are areas which may be subject to infestation by cockroaches or other
vermin, pay particular attention to keeping the appliance and its surroundings in clean condition at
all times.
Any damage which may be caused by cockroaches or other vermin will not be covered by the
appliance guarantee.
Transit bolts
The appliance is fitted with transit bolts to prevent internal damage during transport.
• Packing and all transit bolts must be
removed before using the washer.
When unpacking the base, be
sure to remove the additional
packing support in the middle of
the base packing.
(Packing support may not
be used depending on
models.)
Removing transit bolts
1. To prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove
the bolts along with the rubber bungs.
3. Take out the 4 bolts along with the rubber
bungs by slightly twisting the bung. Keep
the 4 bolts and the spanner for the future
use.
• If they are not removed, it may cause heavy
vibration, noise and malfunction.
• Whenever the appliance is transported, the
transit bolts must be refitted.
2. Unscrew the 4 bolts with
the spanner supplied.
4. Close the holes with the caps supplied.
6
I
nstallation
Installation place requirement
Level floor :
Allowable slope under entire washer is 1˚
Power outlet :
Must be within 1.5 meters of either side of location of
washer. Do not overload the outlet with more than one
appliance.
Additional Clearance :
For wall, door and floor modeling is required.
(10cm : rear /2cm:right & left side)
Do not place or store laundry products on top of
washer at any times.
They can damage the finish or controls.
Positioning
Install the washer on a flat hard floor.
Make sure that air circulation around the washer is not impeded by carpets, rug etc.
• Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar
materials under the washer.
• If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove,
an insulation(85x60cm) covered with aluminum foil on the side facing the cooker or stove,
must be inserted between the two appliance.
• The washer must not be installed in rooms where the temperature can drop below 0°C.
• Please ensure that when the washer is installed, it is easily accessible for the engineer in the
event of a breakdown.
• Adjust all four feet using the transit bolt spanner provided ensuring the appliance is stable,
and a clearance of approximately 20mm is left between the top of the washer and the
underside of the work-top.
7
I
nstallation
■ Electrical connection
1. Do not use an extension cord or double adapter.
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly
qualified person in order to avoid a hazard.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center
• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst
under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing : Place the washing
machine at room temperature for a few hours before putting it into operation.
CAUTION
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit
which powers only that appliance and has no additional outlets or branch circuits. Check the
specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have
the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where
the cord exits the appliance.
■ Washing Machine is to be connected to the water mains using new hose-sets and old hose-sets should
not be used.
■ Connecting water supply hose
▶Water supply pressure must be between 30kPa and 800kPa
(0.3~0.8kgf/cm2)
▶Don’t strip or crossthread when connecting Inlet hose to the valve.
▶If the water supply pressure is more than 1000kPa, a decompression
device should be installed.
• Two rubber seals are supplied with the water inlet hoses. They
are used for preventing water leaks.
• Make sure the connection to taps is tight enough.
• Periodically check the condition of the hose and replace the hose
if necessary.
• Make sure that there is no kink on the hose and that it is not
crushed.
▶When your washer has two valves.
• The Inlet hose which has red connector is for the hot water tap.
• If the washer has two valves, the energy is saved by using hot
valve.
8
I
nstallation
Normal Tap without thread & screw type inlet hose
1. Unscrew the fixing screw to
attach the tap.
2. Push the connector up till the
rubber packing is in tight contact
with the tap. Then tighten the 4
screws.
3. Push the water supply hose
vertically upwards so that the
rubber packing within in the
hose can adhere completely to
the tap and then tighten it by
screwing it to the right.
Normal Tap without thread & one touch type inlet hose
1. Untighten the upper connector
screw.
2. Push the upper connector up till 3. Connect the water supply hose
the rubber packing is in tight
contact with the tap. Then
tighten the 4 screws.
to the middle connector,
pushing the plate down.
• In case the diameter of the tap is
large remove the guide plate.
• Turn the middle connector not
to have water leaked.
• Make sure that the rubber seal
is inside the hose connector.
• To separate the water supply
hose from the middle connector
shut off the tap. Then pull the
inlet hose down, pushing the
plate down.
• Unable water Tap for connectoring
hose.
• Make sure that there are no
kinks in the hose and that it is
not crushed.
9
I
nstallation
This equipment is not designed for maritime use or for use mobile installations such as
caravans, aircraft etc.
Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday),
especially if there is no floor drain(gully) in the immediate vicinity.
When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the
door lock to prevent young children being trapped inside.
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk
of suffocation ! Keep all packaging well away from children
Installation of drain hose
• When installing the drain hose sink,
secure it tightly with a string.
• Proper securing of the drain hose will
protect the floor from damage due to
water leakage.
• The drain hose should not be placed higher
than 100 cm above the floor. Water in the
washer does not drain or drains slowly.
• Proper securing of the drain hose will protect
the floor from damage due to water leakage.
• When the drain hose is too long, do not force
back into the washer. This will cause abnormal
noise.
10
I
nstallation
Level adjustment
1. Adjusting the washing machine level properly prevents excessive
noise and vibration.
Install the appliance on a solid and level floor surface, preferably in a
corner of the room.
NOTE
Timber or suspended type flooring may contribute to
excessive vibration and unbalance errors.
2. If the floor is uneven, adjust the adjustable feet as required.
(do not insert pieces of wood etc. under the feet)
Make sure that all four feet are stable and resting on the floor and
then check that the appliance is perfectly level. (use a spirit level)
※ After the washer is level, tighten the lock nuts up towards of the base of
the washer. All lock nuts must be tightened.
NOTE
In the case that the washing machine is installed on a raised
platform, it must be securely fastened in order
to eliminate the risk that it might fall off.
❊ Diagonal Check
When pushing down the edges of the washing machine top plate diagonally, the machine
should not move up and down at all. (Please, check both of two directions)
If machine rocks when pushing the machine top plate diagonally, adjust the feet again.
Concrete floors
• The installation surface must be clean, dry and level.
• Install washer on a flat hard floor.
Tile floors (Slippery floors)
• Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into 70x70 mm
sections and stick the pieces on to the dry tile where machine is to be placed.)
※ Tread Mate is a self adhesive material used on ladders & steps that prevents slipping.
Wooden floors (Suspended floors)
• Wooden floors are particularly susceptible to vibration.
• To prevent vibration we recommend you place rubber cups under each foot,
at least 15mm thick under the washer, secured to at least 2 floor beams with screws.
• If possible install the washer in one of the corners of the room, where the floor is more stable.
※ Insert the rubber cups to reduce vibration.
※ You can obtain the rubber cups (p/no.4620ER4002B) from the LG svc dept.
Important!
• Proper placement and levelling of the washer ensure long, regular and reliable operation.
• The washer must be absolutely horizontal and stand firmly in position.
• It must not “Seesaw” across corners under load.
• The installation surface must be clean, free from floor wax and other lubricant coatings.
• Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.
11
C
are before washing
Before the first washing
Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash
without clothing. This will remove residues and water from the drum that may have been left
during manufacturing.
Caring before washing
1. Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your garment and
how it should be washed.
2. Sorting
To get the best results, Sort clothes into loads that can be washed with the same wash cycle.
Water temperature and spin speed and different fabrics need to be washed in different ways.
Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can
occur causing discoloration of white etc. If possible, do not wash heavily soiled items with lightly
soiled one.
Soil (Heavy, Normal, Light)
Separate clothes according to amount of soil.
Color (White, Lights, Darks)
Separate white fabrics from colored fabrics.
Lint (Lint producers, Collectors)
Wash lint producers and lint collectors
separately.
3. Caring before loading
Combine large and small items in a load. Load large items first. Large items should not be more than half
the total wash load.
Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.
• Check all pockets to make sure that they
are empty. Items such as nails, hair clip,
matches, pens, coins and keys can damage
both your washer and your clothes.
• Pre treat dirt and stains by brushing a little
detergent dissolved in water onto stains like
collars and cuffs to help shift dirt.
• Close zippers, hooks and strings to
make sure that these items don’t
snag on other clothes.
• Check the folds of the flexible gasket (gray) and
remove any small articles,if any.
• Check inside of the drum and remove any left
items in it for next wash cycle.
• Remove any clothing or items on the flexible
gasket to prevent clothing and the gasket
damages.
12
A dding detergent
Adding detergent and fabric softener
1. The Dispenser Drawer
• Main wash only ➔
• Pre Wash + Main Wash ➔
2. Adding Fabric Softener
• Do not exceed the maximum fill line.
Close the dispenser drawer slowly.
Overfilling can cause early dispensing
of the fabric softener which could stain
clothes.
• Do not leave the fabric softener in the
detergent drawer for more than 2 days.
(Fabric softener could harden)
• Softener will automatically be added
during the last rinse cycle.
• Do not open the drawer when water is
supplied.
• Solvents(benzene, etc) are not
allowable.
NOTE
Do not pour fabric softener
directly on the cloths
13
A dding detergent
3. Detergent dosage
• The detergent should be used according to the
instruction of the detergent manufacture.
• If too much detergent is used, too many suds
can occur and this will decrease the washing
result or cause heavy load to the motor.
• Use powder detergent only for the front
loading washer.
• Detergent usage may need to be adjusted
for water temperature, water hardness,
size and soil level of the load. For best
results, avoid oversudsing.
• Detergent is flushed from the dispenser
at the beginning of the cycle.
5. Using the Tablets
1) Open the door and Tablets into the
drum.
4. Water softener
MAX
2) Load the laundry into the drum.
MAX
MAX
❇ If suds occur too much, pleas reduce the
detergent amount.
❋ Tips
Full load : according to
manufacturer’s recommendation.
Part load : 3/4 of the normal
amount.
Minimum load : 1/2 of full load.
• A water softener, such as Anti limescale
(Clagon) can be used to cut down on the
use of detergent in extremely hard water
areas. Dispense according to the amount
specified on the packaging.
First add detergent and then the water
softener.
• Use the quantity of detergent as for soft
water.
14
3) Close the door.
F
unction
Recommended courses according to the laundry type
Program
Fabric Type
Water
Temp.
(Option)
Option
Color fast garments
- Time Delay
60°C
(shirts, night dresses,
- Steam Wash
pajamas...)and lightly soiled (Cold, 30°C, - Intensive
40°C, 95°C) - Pre Wash
white cotton(underwear)
+
40°C (Cold, - Rinse
Synthetic Polyamide, Acrylic,
Medic
Rinse
30°C, 60°C)
Polyester
Dry
(Option)
Maximum
Load
Cotton
Baby
Care
Lightly soiled baby wear
Delicate Delicate laundry easily
damaged
Cotton
Quick
Cotton bedding with filling
duvet, pillow, blanket, sofa
cover with light filling
Hand
Wash
/Wool
Quick
30
“Hand wash” marked
delicate and wool laundry
Allergy
Care
Colored laundry which is
lightly soiled fast
For clean wash through
eliminate allergy source.
Refresh Cotton mixed, Polyeter
mixed Dress shirts, blouses
- Time Delay
- Steam Wash
60°C
- Intensive
(95°C, 40°C) - Pre Wash
- Rinse+
- Medic Rinse
30°C
(Cold, 40°C)
- Time Delay
- Intensive
- Rinse+
- Time Delay
40°C
- Steam Wash
(Cold, 30°C, - Intensive
- Pre Wash
60°C)
- Rinse+
- Medic Rinse
30°C
(Cold, 40°C)
- Time Delay
- Intensive
- Rinse+
60°C
- Time Delay
- Steam Wash
- Intensive
- Rinse+
- Medic Rinse
No Choose
- Steam Wash
Rating
- Low
- Iron
- Normal
- More
- Time
Less than
4kg
Less than
4kg
_
- Low
- Iron
- Normal
- More
- Time
_
- Low
- Iron
- Normal
- More
- Time
_
Less than
2kg
1 king size
(9 Tog)
Less than
2kg
Less than
2kg
Rating
3 items
❋ Water Temperature : Select the water temperature to the wash cycles.
Always follow garment manufacture’s care label or instructions when laundering.
❋ Intensive : When washing full load or heavily soiled laundry, you can increase effectiveness by choosing
intensive option.
❋ Program setting with “Cotton 60°C + Steam Wash + Intensive” option for test in accordance or in conformity
with EN60456 and IEC60456.
❋ Pre Wash : If the laundry is heavily soiled, “Pre Wash” Cotton is recommended. Pre Wash is available in
Cotton, Cotton Quick, Synthetic and Baby Care program.
❋ Medic Rinse : For high effectiveness or more purity in rinse operation you can choose Medic Rinse option.
Medic Rinse is default in Baby Care program.
15
H ow to use washer
20%
Time Left
1:42
Washing
Temp.
1. Cotton automatically
selected upon power on.
• Press the Power(
) button to start.
• Press the Start/Pause(
• Initial condition
- Wash : Main wash
- Rinse : 3 times
- Spin : 1400 rpm
- Water temperature : 60˚C
- Program : Cotton
) button.
60°C
Rinse
Normal
2. Manual Selecting
• Press the Power(
) button to start.
• Select the conditions which you want to
use, by pressing each button.
For selecting the each conditions, please
refer to the page17~page25
• Press the Start/Pause button.
3. Language Selection
• English is the default language.
Language can be changed only when
LCD is on. Power On and then press the
Time delay and Steam Wash button
simultaneously for 3 seconds until the
Select a Language menu is displayed.
Select a Language
English
Spanish
Portuguese
Italian
• Rotation of the program dial will cycle
through Spanish, Portuguese, Italian,
German, French, Dutch, Greek and then
back to English.
16
H ow to use washer
20%
Time Left
1:42
Washing
Temp.
(1)
(2)
(1) Button : Power
(2) Dial : Program
(3) Button : Start/Pause
(4) Button : Time Delay
(3)
(4)(5)
(6)
(5) Button : Steam Wash
(6) Button : Temperature
(7) Button : Spin
(8) Button : Option
Power
60°C
(7)
Rinse
Normal
(8)
(9) (10)
(11)
(9) Button : Child Lock
(10) Button : Tub Clean
(11) Dial : Dry
Program
1. Power
• Press the Power(
off.
) button to turn power on and
• To cancel the Time Delay function, the Power(
button should be pressed.
2. Initial Program
• When the Power(
) button is pressed, the
washer is ready for Cotton program. And the
other initial conditions as follows.
• So, if you want to advance into the washing
cycle without changing the program, just
press Start/Pause(
) button and then the
washer will proceed.
■ Initial program
)
• 9 programs are available according to the
laundry type.
• Lamp will light up to indicate selected program.
• When Start/Pause(
) button is pressed, the
Cotton program is automatically selected.
- By turning the Program dial, the program is
selected in order of “Cotton - Cotton Quick Synthetic - Delicate - Hand Wash/Wool Quick 30 - Refresh - Allergy Care - Baby Care”.
Regarding to the laundry type for each program
Please refer to the page15.
-Cotton Program / Main Wash /
Normal Rinse / 1400 rpm / 60˚C
17
H ow to use washer
Start/Pause
Time Delay
Time Delay
Time Delay
Time Left
3:00
To increase the delay wash time
press on the time delay button.
1. Start
• This Start/Pause button is used to start
wash cycle or pause the wash cycle.
2. Pause
• If temporary stop of wash cycle is needed,
press “Start/Pause” button.
• When in Pause, the power is turned off
automatically after 4 minutes.
• NB. The door will not open before 1 to 2
minutes when Pause is selected,
or at the end of the wash cycle.
3. Detecting
7kg
60°C
Rinse
3
• While the "Detecting" is shown in the display
the machine rotates slowly and detects how
many laundries are loaded in the drum. It
will take a few seconds.
• Available in Cotton, Cotton Quick, Allergy
Care, Synthetic and Baby Care program.
4. Door Lock
20%
Time Left
1:42
Washing
Temp.
60°C
Rinse
3
• Lights whenever the door of the washer is
locked.
• The door can be unlocked by pressing the
Start/Pause button to stop the washer.
• The door can be opened after a short delay.
18
3:00
Preparing washing before starting “Time Delay”
- Turn on the water tap.
- Load laundry and close the door.
- Place the detergent and fabric softener in
the drawer.
• How to set “Time Delay”
- Press Power button.
- Turn the Program dial to select
the program you require.
- Press Time Delay button and set the
desired time.
- Press the Start/Pause button.
• If Time Delay button is pressed, “3:00” is
displayed. The maximum delayed time is
19:00 hours and the minimum time is 3:00
hours.
Time Left
Detecting
Temp.
Time Left
The cycle will end after
3 hours.
• Each pressing of the button advances time
delay by one hour.
• To cancel the time delay, press the
Power button.
• Time Delay is ‘expected time’ from the
present to the completion of washing cycle
or selected process (Wash, Rinse, Spin).
• According to the condition of water supply and
temperature, the delayed time and the actual
washing time may vary.
H ow to use washer
Steam Wash
Refresh
■ Refresh cycle
Steam
Time Left
1:42
Use on tough stained clothes.
• For slightly wrinkled clothes which have
been stored for an extended time.
It just makes wrinkled clothes easy to iron
(Do not load wet clothes).
• Wrinkles will be reduced.
■ How to use Refresh cycle
By pressing the Steam Wash button, Steam
Function Can be selected.
When Steam Function is selected, Steam wash
(
) LED lights on.
1. Turn on the washer and select the Refresh program.
2. Load 3 items or less and close the door.
3. Press the Steam Wash button repeatedly until the
desired and correct number of items is displayed.
Initial display is 2 items
Steam
Steam Wash is
• For normally soiled full load.
• For tough stained clothes, underway, or baby
Clothes.
• Steam Wash is available with Cotton, Synthetic,
Baby Care program.
Refresh cycle is fixed Steam wash.
Program
Cotton
Synthetic
Baby Care
Temperature
60°c (30°c, 40°c, 95°c)
40°c (30°c, 60°c)
95°c (40°c, 60°c)
• This option features upgraded washing
performance with low energy.
• Do not load delicates such as wool, silk, and
easily discolored clothes.
NOTE:
- Steam wash is a highly concentrated and
efficient.
It may seem there is no water inside the
drum(normal condition).
- During the steam cycle the strong steam
spray may not be seen through the door
(normal condition).
- During the steam operation, a spraying sound
will be heard. (normal condition)
- Do not try to open the door while operating.
Steam can cause severe burns.
! CAUTION:
- Do not reach into the washer while operating.
Steam can cause severe burns.
Time Left
0:19
Refresh
Press the
Steam Wash button
Steam
Time Left
Load
0:19
3 items.
4. Press the Start/Pause button
[Precautionary Notes]
- The Refresh cycle is not like other washing or
drying cycles.
- Due to the characteristic of cotton fibers, this cycle
is not recommended for 100% cotton clothing.
- Remove stains from clothing before using the
Refresh cycle to prevent permanently setting the
stains by high heat.
- Be sure that the faucet is open. This cycle uses a
little water to produce steam.
- Be careful not to touch the door. It can be very hot.
- Do not open the door while operating.
Steam can cause severe burns.
- After removing clothes from the Refresh cycle they
may feel slightly damp wait at least 10 minutes
before putting the clothes on.
- Best result are achieved when articles are of similar
size and fabric type. Do not overload
(Load less than 3 dress shirtes)
! CAUTION:
- Do not reach into the washer while operating.
Steam can cause severe burns.
- Keep pets away from the washer.
19
H ow to use washer
Option
Water Temp.
• By pressing the Temp.
button, the water
temperature can be
selected.
By pressing each
the button, each
function will be
selected.
- Cold
- 30˚C / 40˚C / 60˚C / 95˚C
• Water temperature can be selected as
below according to the program.
1. Intensive
- Synthetic & Cotton Quick
Cold – 30˚C – 40˚C – 60˚C
• When washing full load or heavily soiled
laundry, you can increase effectiveness by
choosing intensive option.
• By selecting the Intensive option, the wash
time may be extended, depending on the
program selected.
• To use this option, press the intensive button
once before the wash program is started.
- Delicate & Quick 30 & Hand Wash/Wool
Cold – 30˚C – 40˚C
2. Pre Wash
- Baby Care
40˚C – 60˚C – 95°C
- Cotton
Cold – 30˚C – 40˚C – 60˚C – 95˚C
The required temperature lamp will light up for
identification.
For the more detailed information, please refer
to the page15.
• Use this option for load that need pretreatment.
Add 16 minutes pre wash and drain.
- When using Pre Wash option, do not use
liquid detergent in the main wash
comportment. Use powder for the main wash.
• Available in Cotton, Cotton Quick, Synthetic
and Baby Care program.
2. Rinse+
• Used to additional rinse, which may assist in
removing traces of detergent residue.
• By selecting Rinse+ function, the Rinse
Time and the Rinse water are increased.
4. Medic Rinse
• For high effectiveness or more purity in rinse
operation you can choose Medic Rinse option.
• Available in Cotton, Cotton Quick, Allergy Care,
Synthetic and Baby Care program.
• Medic Rinse is default in Baby Care program.
The required temperature lamp will light up for
identification.
20
H ow to use washer
Child lock
Tub Clean
If you choose to lock the buttons on the
control assembly to prevent tampering, this
function may be selected.
• Child lock can be set by pressing and
holding the Rinse+ and Medic Rinse
button simultaneously.
(About three seconds)
Tub Clean course can be set by pressing
and holding Intensive and Pre Wash button
simultaneously.
When Tub Clean course is set, display
“Tub Clean”, and all buttons are inoperable.
20%
20%
Time Left
1:42
Rinse
3
60°C
• To deactivate Child lock system, press and
hold the Rinse+ and Medic Rinse button
simultaneously again.
(About three seconds)
20%
Time Left
1:42
Rinse
3
Child Lock is off.
Temp.
60°C
1:32
Tub Clean
Child Lock is on.
Temp.
Time Left
• To change to the desired program, whilst in
child lock mode.
1. Press and hold both Rinse+ and Medic
Rinse button together once again.
(About three seconds)
2. Press the Start/Pause button.
3. Select the desired program and press the
Start/Pause button again.
• The child lock can be set at any time and it
can be deactivated only by using child-lock
cancel process. Turning the power off and
operational errors will not affect child-lock.
TUB CLEAN is special cycle to clean the
inside of the washer. This cycle uses higher
water level with higher spin speed. Perform
this cycle regularly.
How to use the Tub Clean cycle:
1. Remove any clothing or items from the
washer and close the door.
2. Open the dispenser drawer and add Anti
limescale (Calgon) to the Main wash
compartment.
NOTE: Do not add any detergent to the
detergent compartments. Excessive
suds may generate and leak from the
washer.
3. Close the dispenser drawer slowly.
4. Power On and then press and hold
Intensive and Pre Wash button for 3 seconds.
then “ Tub Clean” is displayed in LCD
5. Press the Start/Pause button to start.
6. After the cycle is complete, leave the door
open to dry around the washer door
opening, flexible gasket and door glass.
! CAUTION: If there is a small child, be
careful not to leave the door
open for too long.
21
H ow to use washer
Spin
• By pressing the Spin
button, the spin speed
can be chosen.
1. Spin selection
• Spin speed is available according to the
program as follows.
- Cotton & Quick 30 & Cotton Quick
No Spin – 400 – 800 – 1000 – 1400
- Synthetic & Hand Wash/Wool &
Allergy Care & Baby Care
No Spin – 400 – 800 – 1000
- Delicate
No Spin – 400 – 800
2. No spin
• If “No Spin” is selected, the washer stops
after draining water.
3. Spin Only
1. Press the Power button.
2. Set the desired spin speed.
3. Press the Start/Pause button.
The required lamp will light up for
identification.
22
Dry
• This washer-dryer’s
automatical process
from washing to drying
can be selected easily.
• For most even drying, make sure all articles
in the clothes load are similar in material and
thickness.
• Do not overload dryer by stuffing too many
articles into drum. Items must be able to
tumble freely.
• If you open door and remove load before
dryer has finished its cycle, remember to
press the Start/Pause button.
• After the end of dry, “Cool down” is
displayed.
By pressing the “Start/Pause” button the
program can be ended. If you not press the
“Start/Pause” button, the program is ended
after about 4 hours. “Cool down” Cooling
Cycle.
H ow to use washer
Dry
1. Drying Automatic guide
• Use your Automatic Cycles to dry most loads.
Electronic sensors measure the temperature of
the exhaust to increase or decrease drying
temperatures for faster reaction time and tigher
temperature control.
• If a load is not as dry as you like, complete
drying using a time cycle.
NOTE
The Estimated drying time varies from
the actual drying time with an
Automatic. The type of fabric, size of
the load, and the dryness selected
affect drying time.
2. Drying Time Guide
(Manual operation)
• By turnning the Dry dial, the drying time can be
selected.
• Drying course can last up to 120min. When
selecting drying only, drying course will start
after 15min spining.
• These drying times are given as a guide to
help you set your dryer for manual drying.
Drying times can vary greatly depending on
dampness, room temperature and type of
fabric and your own experience will be your
best guide.
• Low Temp. : For Synthetics select
❋ The standard laundry weight which shows
how much laundry to put into the washer.
• Iron : If you want to iron clothes
• Normal : For Cottons select
• More : For washable nappies select
• Time (30/60/120 minutes)
- 30 min : Cotton 1.5kg
- 60 min : Cotton 3kg
- 120 min : Towel 4kg
23
H ow to use washer
• When loading, shake out each handful of
clothes so that they can tumble freely.
Items should not be loaded in a tangled
condition, as this will lengthen the drying
time.
Woolen Articles
- Do not tumble dry woolen articles. Pull them
to their original shape, they ary them flat.
Woven and Loopknit Materials
- Some woven and loopknit materials may
shrink, by varying amounts, depending on
their quality.
- Always stretch them out immediately after drying.
Permanent Press and Synthetics
- Do not overload your dryer.
- Take out permanent press articles as soon
as the dryer stops to reduce wrinkles.
Fibre or Leather Materials
- Always check the manufacture’s
instructions.
Baby Clothes and Night Gowns
- Always check the manufacture’s
instructions.
Rubber and Plastics
- Do not dry any items made from or
containing rubber or plastics, such as:
a) aprons, bibs, chair covers
b) curtains and tablecloths
Fiberglass
- Do not dry fiberglass articles in your dryer.
Glass particles left in the dryer could be
picked up by your clothes the next time you
use the dryer and irritate your skin.
24
3. Completion of Drying
When drying cycle is completed,
Cool down is displayed on the Multi
display.
The Cool down is setting
automatically when a drying cycle is
complete.
When you are not remove a load of
clothes from the dryer as soon as it
stops, wrinkles can form.
The Cool down operating periodically
tumbles, rearranges and fluffs the load to
avoid wrinkles without heat for up to 4
hours.
The Cool down message will continue
to display until the clothes are removed or
the Start/Pause button is pressed.
H ow to use washer
Display
20%
Time Left
3. Completion of washing
• When washing cycle is completed,
“End of cycle” is displayed on the “Multi
display”.
1:42
Washing
Temp.
60°C
Rinse
3
4. Time left
1. Special function display
• When Child lock is selected, the “
on.
” lamp is
• When time delay is selected, it shows the
remaining times to finish the selected program.
2. Self diagnose display
• If the washer encounters a fault during
operation, the associated fault will be
displayed.
“
” : Water pressure sensing error
“
” : Problem of overfilling water
“
” : Door is not closed
“
” : Over load in motor
“
” : Water inlet trouble
“
” : Drainage trouble
“
” : Unbalanced load
“
” : Water temperature trouble
“ AE ” : Water leaks
“ PF ” : The washer experienced a power
failure.
“ CE ” : Over load in motor
“
” : Dry heater or thermostat trouble.
If these error letters are displayed, please refer to
the troubleshooting page30 and follow the guide.
• During washing cycle, the remaining
washing time is displayed.
• Recommended program by manufacturer.
- Cotton : around 1 hour and 51 minutes
- Synthetic :
around 1 hour and 28 minutes
- Baby Care : around 2 hours and 27 minutes
- Delicate : around 1 hour and 11 minutes
- Hand Wash/Wool :
around 1 hour and 07 minutes
- Quick 30 : around 30 minutes
- Cotton Quick :
around 1 hour and 26 minutes
- Allergy Care :
around 2 hours and 07 minutes
- Refresh : around 24 minutes
• The washing time may vary by the
amount of laundry, water pressure, water
temperature and other washing conditions.
• If an unbalanced load is detected or if the
suds removing program operates, the
wash time may be extended.
(Max. increasing time is 45 minutes.)
Est. Time Remaining
• This display shows the estimated time
remaining in the cycle when operating.
• This washer automatically detects the
wash load (weight) and optimizes the
washing time. After detecting, the display
will show the adjusted time remaining.
Status Indicator
• It shows elapsed time of the cycle the
washer is operating.
25
M aintenance
❋ Before cleaning the washer interior, unplug the electrical power cord to avoid electrical
shock to avoid electrical shock hazards.
❋ When disposing of the appliance, cut off the mains cable, and destroy the plug Disable
the door lock to prevent young children being trapped inside.
The water inlet filter
-"
" error message will blink on the control panel when water does not enter the
detergent drawer.
- If water is very hard or contains traces of lime deposit, the water inlet filter may
become clogged.
It is therefore a good idea to clean it from time to time.
1. Turn off the water tap.
2. Unscrew the water inlet hose.
3. Clean the filter using a hard bristle
brush.
4. Tighten up the inlet hose.
26
M aintenance
The drain pump filter
❋ The drain filter collects threads and small objects left in the laundry.
Check regularly that the filter is clean to ensure smooth running of your machine.
! CAUTION
First drain using the drain hose and then open the pump filter to
remove whatever any threads or objects.
Be careful when draining if the water is hot.
❋ Allow the water to cool down before cleaning the drain pump, carrying out
emergency emptying or opening the door in an emergency.
1. Open the lower cover cap (
) by using
a coin.
Drain plug ( ) to pull out the hose.
001
1
2. Unplug the drain plug (
), allowing the
water to flow out. At this time use a
vessel to prevent water flowing on to the
floor. When water does not flow any
more, turn the pump filter ( ) open to
the left.
3
2
3. Remove out any foreign material from
the pump filter (
).
4. After cleaning, turn the pump filter (
)
clockwise and insert the drain plug ( )to
the original place. close the lower cover
cap.
3
2
27
M aintenance
Dispenser drawer
❋ After a while detergents and fabric softeners leave a deposit in the drawer.
MAX
MAX
• It should be cleaned from time to time with a jet of running water.
• If necessary it can be removed completely from the machine by pressing the catch
downward and by pulling it out.
• To facilitate cleaning, the upper part of the fabric softener compartment can be removed.
The drawer recess
❋ Detergent can also accumulate inside the recess which should
be cleaned occasionally with an old toothbrush.
• Once you have finished cleaning, replace the drawer and run a
rinse cycle without laundry.
The washing drum
• If you live in a hard water area, limescale may continuously build up in places where it cannot be
seen and thus not easily removed.
Over time the build up of scale clogs appliances, and if it is not kept in check these may have to be
replaced.
• Although the washing drum is made of Stainless steel, specks of rust can be caused by small metal
articles (paper clips, safety pins) which have been left in the drum.
• The washing drum should be cleaned from time to time.
• If you use descaling agents, dyes or bleaches, make sure they are suitable for washing machine
use.
❋ Descaler may contain chemicals that may damage part of your washing machine.
❋ Remove any spots with a stainless steel cleaning agent.
❋ Never use steel wool.
28
M aintenance
The water circulation nozzle & Steam nozzle
• Clean the water circulation nozzle and Steam nozzle, if clogged.
Cleaning your washer
1. Exterior
Proper care of your washer can extend its life.
The outside of the machine can be cleaned with warm water and a neutral non abrasive
household detergent.
Immediately wipe off any spills. Wipe with damp cloth.
Try not to hit surface with sharp objects.
❋ IMPORTANT: Do not use methylated spirits, diluents or similar products.
2. Interior
Dry around the washer door opening, flexible gasket and door glass.
Run washer through a complete cycle using hot water.
Repeat process if necessary.
NOTE
Remove hard water deposits using only cleaners labeled as safe for washing
machine.
Winterizing instructions
If the washer is stored in an area where freezing may occur or moved in freezing
temperatures, follow these instructions to prevent damage to the washer:
1. Turn off water supply tap.
2. Disconnect hoses from water supply and drain water from hoses.
3. Plug electrical cord into a properly grounded electrical outlet.
4. Add 1gallon(3.8L) of nontoxic recreational vehicle(RV) antifreeze into an empty wash drum.
Close the door.
5. Set spin cycle and let washer spin for 1minute to drain out all water.
Not all of the RV antifreeze will be expelled.
6. Unplug electrical power cord, dry the drum interior, and close the door.
7. Remove dispenser drawer, drain and dry excessive water from the compartments.
8. Store washer in an upright position.
9. To remove antifreeze from washer after storage, run empty washer
through a complete cycle using detergent. Do not add wash load.
29
T
roubleshooting guide
❋ This washing machine is equipped with automatic safety functions which detect and
diagnose faults at an early stage and react appropriately.
When the machine does not function properly or does not function at all, check the
following points before you contact your service provider.
Symptom
Possible Cause
Solution
Rattling and
clanking noise
• Foreign objects such as coins or
safety pins maybe in drum or
pump.
Stop washer and check drum
and drain filter.
If noise continues after washer
is restarted, call your authorized
service centre.
Thumping sound
• Heavy wash loads may produce
a thumping sound. This is usually
normal.
If sound continues, washer is
probably out of balance. Stop and
redistribute wash load.
Vibrating noise
• Have all the transit bolts and
packing been removed?
• Are all the feet resting firmly on
the ground?
If not removed during
installation, refer to Installation guide
for removing transit bolts.
Wash load may be unevenly
distributed
in drum. Stop washer and
rearrange wash load.
Water leaks.
• Fill hoses or drain hose are loose
at tap or washer.
Check and tighten hose connections.
• House drain pipes are clogged.
Unclog drain pipe. Contact plumber
if necessary.
Too much detergent or unsuitable
detergent may cause excessive
foaming which may result in water
leaks.
Oversudsing
Water does not enter
washer or it enters
slowly
Water in the washer
does not drain or
drains slowly.
30
• Water supply is not adequate in
area.
Check another tap in the house.
• Water supply tap is not
completely open.
Fully open tap.
• Water inlet hose(s) are kinked.
Straighten hose(s).
• The filter of the inlet hose(s) are
clogged.
Check the filter of the inlet hose(s).
• Drain hose is kinked or clogged.
Clean and straighten the drain hose.
• The drain filter is clogged.
Clean the drain filter.
T
roubleshooting guide
Symptom
Washer does not start
Possible Cause
• Electrical power cord may not
be plugged in or connection
may be loose.
Make sure plug fits tightly in wall
outlet.
• House fuse blown, circuit
breaker tripped, or a power
outage has occurred.
Reset circuit breaker or replace fuse.
Do not increase fuse capacity.
If problem is a circuit overload, have
it corrected by a qualified electrician.
Turn on water supply tap.
• Water supply tap is not turned
on.
Washer won’t spin
Solution
❋ Check that the door is firmly
shut.
Close the door and press the
Start/Pause button. After pressing
the Start/Pause button, it may take
a few moments before the washer
begins to spin. The door must lock
before spin can be achieved.
Door does not open
Once started, the door can not be
opened for safety reasons.
Wait one or two minutes before
opening the door to give the electric
locking mechanism time to release.
Wash cycle time
delayed
The washing time may vary by the
amount of laundry, water
pressure, water temperature and
other using conditions.
If the imbalance is detected or if the
suds removing program works, the
wash time shall be increased.
Dry problem
• Does not dry
Do not overload.
Check that the washer is draining
properly to extract adequate water
from th load.
Clothes load is too small to tumble
properly. Add a few towels.
31
roubleshooting guide
T
Symptom
Possible Cause
Solution
• Water supply is not adequate in area
• Water supply taps are not completely open.
• Water inlet hose(s) are kinked.
• The filter of the inlet hose(s) are clogged.
Check another tap in the house.
Fully open tap.
Straighten hose(s).
Check the filter of the inlet hose(s).
• Drain hose is kinked or clogged.
• The drain filter is clogged.
Clean and straighten the drain hose.
Clean the drain filter.
For more detailed information,
please refer to “The drain pump filter” on page27
• Load is too small.
• Load is out of balance.
• The appliance has an unbalance detection
and correction system. If individual heavy
articles are loaded (ex. bath mat, both robe,
etc.), this system may stop spinning or even
interrupt the spin cycle altogether.
• If the laundry is still too wet at the end of the
cycle, add smaller articles of laundry to
balance the load and repeat the spin cycle.
Add 1 or 2 similar items to help
balance the load.
Rearrange load to allow proper
spinning
• Is the door opened or not
completely closed?
Close the door completely.
❋ If “
”is not released, call for service.
Unplug the power plug and call for service.
• Water overfills due to the faulty water valve.
Close the water tap.
Unplug the power plug.
Call for service.
• Water level sensor has malfunctioned.
• Over load in motor.
• Over load in motor.
• Water leaks
• The washer experienced a power failure.
• Check water supply.
32
Call for service.
Restart the cycle.
Turn the water tap on.
If
is not released, unplug power plug
and call service.
T
erms of Warranty
What Is Not Covered:
• Service trips to your home to teach you how to use the product.
• If the product is connected to any voltage other than that shown on the rating plate.
• If the fault is caused by accident, neglect, misuse or Act of God.
• If the fault is caused by factors other than normal domestic use or use in accordance
with the owner's manual.
• Provide instruction on use of product or change the set-up of the product.
• If the fault is caused by pests for example, rats or cockroaches etc..
• Noise or vibration that is considered normal for example water drain sound, spin
sound, or warming beeps.
• Correcting the installation for example, levelling the product, adjustment of drain.
• Normal maintenance which recommended by the owner's manual.
• Removal of foreign objects / substances from the machine, including the pump and
inlet hose filter for example, grit, nails, bra wires, buttons etc.
• Replace fuses in or correct house wiring or correct house plumbing.
• Correction of unauthorized repairs.
• Incidental or consequential damage to personal property caused by possible defects
with this appliance.
• If this product is used for commercial purpose, it is not warranted.
(Example : Public places such as public bathroom, lodging house, training
center, dormitory)
If the product is installed outside the normal service area, any cost of
transportation involved in the repair of the product, or the replacement of a
defective part, shall be borne by the owner.
33
M emo
34
Download PDF

advertising