LG | DH6340P | LG DH6340P Owner’s Manual

ENGLISH
OWNER’S MANUAL
DVD Home
Theater
System
Please read this manual carefully before operating
your set and retain it for future reference.
DH6340H (DH6340H, S64H1-S/ C/ W)
DH6340P (DH6340P, S64H1-S/ C/ W, S64B1-S)
www.lg.com
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with
arrowhead symbol within an
equilateral triangle is intended to
alert the user to the presence of
uninsulated dangerous voltage
within the product’s enclosure that
may be of sufficient magnitude to
constitute a risk of electric shock
to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not
try to open the enclosure.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
Getting Started
This device is equipped with a portable battery or
accumulator.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
Notes on Copyrights
yy This product incorporates copyright protection
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Rovi, and is intended for home and
other limited viewing uses only unless otherwise
authorized by Rovi. Reverse engineering or
disassembly is prohibited.
yy Under the U.S. Copyright laws and Copyright
laws of other countries, unauthorized recording,
use, display, distribution, or revision of television
programs, videotapes, BD-ROM discs, DVDs, CDs
and other materials may subject you to civil and/
or criminal liability.
1
Getting Started
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
3
4
Table of Contents
Table of Contents
1
Getting Started
2
Safety Information
6
Unique Features
6
– Portable In
6
– USB Direct Recording
6
– Full HD up-scaling
6
– Home Theater Speaker ez Setup
6Accessories
7Introduction
7
– Playable Discs
7
– About the “7” Symbol Display
7
– Symbols Used in this Manual
7
– Regional Codes
8
Playable file Requirement
9
Remote control
10 Front panel
11 Rear panel
2Connecting
12
14
15
16
16
17
17
18
18
19
19
19
19
Assembling the speaker
Attaching the speakers to the unit
Positioning the system
Connections to Your TV
– HDMI Out Connection
– What is SIMPLINK?
– Video Connection
– Resolution Setting
Video Output Resolution
Optional Equipment Connection
– AUX In Connection
– AUDIO (PORT. IN) In Connection
– Listening to music from your portable
player or external device
20 – USB Connection
21 – OPTICAL In connection
21 – Home theater speaker ez setup
22 Antenna Connection
3 System Setting
23 Adjust the setup settings
23 – OSD Initial language settings Optional
23 – To display and exit the Setup menu
24 – Language
24 – Display
25 – Audio
26 – Lock (Parental Control)
27 – Others
Table of Contents
4Operating
5Troubleshooting
28
28
29
29
30
30
30
30
30
30
30
31
32
33
33
33
33
33
33
33
33
33
34
34
34
34
34
34
35
35
36
36
37Troubleshooting
Using the Home Menu
Basic Operations
Other Operations
– Displaying Disc Information on-screen
– To display the DVD Menu
– To display the DVD title
– 1.5 times speed playback
– Screen Saver
– Starting play from selected time
– Resume playback
– Changing subtitle code page
– Marked Playback
– Viewing a PHOTO file
– Sleep Timer Setting
– Dimmer
– Turn off the sound temporarily
– Last Scene Memory
– Power Resume - Optional
– System Select - Optional
– Adjust the speaker level settings
– VOCAL FADER
– Auto power down
Radio Operations
– Listening to the radio
– Presetting the Radio Stations
– Deleting all the saved stations
– Deleting a saved station
– Improving poor FM reception
Sound adjustment
– Setting the surround mode
Advanced Operations
– Recording to USB
6Appendix
38Maintenance
38 – Handling the Unit
38 – Notes on Discs
39 Area Code List
40 Language code List
41 Trademarks and Licenses
42Specifications
5
1
2
3
4
5
6
6
Getting Started
Unique Features
1
Portable In
Accessories
Please check and identify the supplied accessories.
Getting Started
Listen to music from your portable device. (MP3,
Notebook, etc.)
USB Direct Recording
Records music from CD to your USB device.
Remote control (1)
Battery (1)
FM antenna (1)
Speaker cables (5)
HDMI cable (1)
Video cable (1)
Full HD up-scaling
Views Full HD picture quality with simple setup.
Home Theater Speaker ez
Setup
Listen to sounds from TV, DVD and Digital device
with vivid 5.1 (2.1 or 2.0) ch mode.
Getting Started
Introduction
Playable Discs
DVD-VIDEO (8 cm/12 cm disc)
Discs such as movies that can be
purchased or rented.
DVD±R (8 cm/12 cm disc)
Video mode and finalized only.
DVD-RW (8 cm/12 cm disc)
Video mode and finalized only.
DVD+R: Video mode only
Supports the double layer disc also.
DVD+RW (8 cm/12 cm disc)
Video mode and finalized only.
Audio CD: Music CDs or CD-R/CDRW in music CD format that can be
purchased.
About the “7” Symbol Display
“7” may appear on your TV display during
operation and indicates that the function explained
in this owner’s manual is not available on that
specific media.
Symbols Used in this Manual
r
DVD-Video, DVD±R/RW in Video
mode or VR mode and finalized
t
Audio CDs
y
Video files contained in the
USB/Disc
u
Audio files contained in the
USB/Disc
i
Photo files
,,Note
Indicates special notes and operating features.
,,Tip
Indicates tip and hints for making the task easier.
>>Caution
Indicates cautions for preventing possible damages
from abuse.
Regional Codes
This unit has a regional code printed on the rear of
the unit. This unit can play only DVD discs labeled
same as the rear of the unit or “ALL”.
yy Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your unit’s regional code or
the disc cannot play.
yy If you try to play a DVD with a different regional
code from your unit, the message “Check
Regional Code” appears on the TV screen.
1
Getting Started
This unit plays DVD±R/RW and CD-R/RW that
contains audio titles, DivX, MP3, WMA and/or
JPEG files. Some DVD±RW/DVD±R or CD-RW/
CD-R cannot be played on this unit due to the
recording quality or physical condition of the disc,
or the characteristics of the recording device and
authoring software.
7
8
Getting Started
Playable file
Requirement
1
Getting Started
Music file requirement
MP3/ WMA file compatibility with this unit is limited
as follows :
yy Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
yy Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
yy Support Version : v2, v7, v8, v9
yy Maximum files : Under 999
yy File extensions : “.mp3”/ “.wma”
yy CD-ROM file format : ISO9660/ JOLIET
yy We recommend that you use Easy-CD Creator,
which creates an ISO9660 file system.
yy You have to set the disc format option to
[Mastered] in order to make the discs compatible
with the LG players when formatting rewritable
discs. When setting the option to Live File
System, you cannot use it on LG players.
(Mastered/ Live File System : Disc format system
for Windows Vista)
The DTS is not supported. In case of DTS audio
format, audio is not output.
Photo file requirement
Photo file compatibility with this unit is limited as
follows :
yy Max pixel in width : 2760 x 2048 pixel
yy Maximum files : Under 999
yy Some discs may not operate due to a different
recording format or the condition of disc.
yy File extensions: “.jpg”
yy CD-ROM file format : ISO9660/ JOLIET
DivX file requirement
DivX file compatibility with this unit is limited as
follows:
yy Available resolution: within 720 x 576 (W x H)
pixels.
yy The file name of the DivX subtitle should be
entered within 45 characters.
yy Playable video file bit rate : 7 Mbps and under.
yy If there is impossible code to express in the
DivX file, it may be displayed as “ _ “ mark on the
display.
yy Frame rate : less than 30 fps.
yy If the video and audio structure of recorded
files is not interleaved, either video or audio is
outputted.
yy Playable DivX file : “.avi”, “.mpg”, “.mpeg”, “.divx”
yy Playable Subtitle format : SubRip (*.srt/ *.txt),
SAMI (*.smi), SubStation Alpha (*.ssa/ *.txt),
MicroDVD (*.sub/ *.txt), SubViewer 2.0 (*.sub/
*.txt), Vobsub (*.sub)
yy Playable Codec format :
“DIVX 3.11”, “DIVX4”, “DIVX5”. “DIVX6”
“MP4V3”, “3IVX”
yy Playable Audio format : “AC3”, “PCM”, “MP3”, “WMA”,
yy Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
yy Bit rate : within 32 to 320 kbps (MP3), 40 to 192
kbps (WMA)
yy For Discs formatted in Live file system, you can
not it on this unit.
yy If the name of movie file is different from that of
the subtitle file, during playback of a DivX file,
subtitle may not be display.
yy If you play a DivX file differ from DivXspec, it may
not operate normally.
Getting Started
9
Remote control
• • • • • • d • • • • • •
SLEEP : Sets the System to turn off
automatically at a specified time.
(Dimmer : The display window will
be darken by half.)
SPEAKER LEVEL : Sets the sound
level of desired speaker.
m INFO/DISPLAY : Accesses OnScreen Display.
VOL -/+ (Volume) : Adjusts
speaker volume.
n HOME : Displays the [Home
Menu].
DISC MENU : Accesses the menu
on a DVD disc.
• • • • • • b • • • • • •
W/S/A/D (up/ down/ left/
right) : Used to navigate on-screen
displays.
PRESET +/- : Selects programme
of Radio.
TUNING +/- : Tunes in the desired
radio station.
b ENTER : Acknowledges menu
selection.
Presetting the radio stations.
x RETURN : Moves backwards
in the menu or exits the setup
menu.
Battery Installation
TITLE: If the current DVD title has
a menu, the title menu appears
on the screen. Otherwise, the disc
menu may not appear.
• • • • • • c • • • • • •
Z STOP : Stops playback.
d PLAY, MONO/STEREO : Starts
playback. Selects Mono/ Stereo.
Remove the battery cover on the
rear of the remote control, and
insert one (size AAA) battery with
4 and 5 matched correctly.
M PAUSE/STEP : Pauses playback.
• • • • • • a • • • • • •
c/v SCAN : Searches
backward or forward.
P RADIO&INPUT : Changes
input sources.
MARKER : Marks play list.
1 POWER : Switches the unit ON
or OFF.
B OPEN/CLOSE : Opens and
C/V SKIP : Goes to the
next or previous chapter / track /
file.
SOUND EFFECT : Selects a sound
effect mode.
OPTICAL : Changes input source
to optical directly.
MUTE : Mutes the sound.
• • • • • • e • • • • • •
0-9 numerical buttons : Selects
numbered options in a menu.
h REPEAT : Selects a play
mode. (Repeat/ Random)
CLEAR : Removes a number when
setting the password.
• • • • • • f • • • • • •
TV Control buttons : Controls the
TV. (LG TV only)
-- You can control the sound
level, input source, and power
switching of LG TVs as well.
Hold POWER (TV) and press PR/
CH (W/S) button repeatedly
until the TV turns on or off.
X REC : USB Direct Recording.
?: This button is not available.
MIC VOL -/+ : Adjusts microphone
volume.
ECHO VOL -/+ : Adjusts echo
volume.
VOCAL FADER: You can enjoy the
function as karaoke, by reducing
singer vocal of music in the
various source.
1
Getting Started
closes the disc tray.
10
Getting Started
Front panel
1
Getting Started
a Disc Tray
b Display window
Shows the current status of the unit.
c Microphone jacks 1/2
d PORT. IN
Connects to a portable player with audio
outputs.
e USB Port
Connects a USB device.
f R (OPEN/CLOSE)
Opens or closes the disc tray.
g T (PLAY/PAUSE)
Starts playback.
Pauses playback temporarily, press again to exit
pause mode.
h I (STOP)
Stops playback.
iF (FUNCTION)
Changes the input source or function.
j-/+(Volume)
Adjusts speaker volume.
k 1/! (POWER)
Switches the unit ON or OFF.
Getting Started
11
Rear panel
1
Getting Started
a Power cord
b Speaker connectors
Connects the speaker cables.
c Cooling Fan
d ANTENNA
FM- Connects the FM wired antenna
e AUX (L/R) INPUT
Connects to an external source with 2 channel
audio outputs.
f VIDEO OUT
Connects to a TV with video inputs.
g HDMI OUT
Connects to TV with HDMI inputs.
(Interface for digital audio and video)
h OPTICAL IN
Connects to optical audio equipment.
12
Connecting
Assembling the
speaker
Preparation
2
Connecting
Speaker
Speaker cables
Base
Screws
1. Attach the speaker to the base.
Connecting
2. Secure the connection with a supplied screw.
13
4. Connect the speaker wire to the terminal on the
speaker.
Make sure the wire marked black goes in to the
terminal marked “–” (minus) and the other wire
goes in to the terminal marked “+” (plus).
2
Connecting
3. Thread the speaker cord through the hole in the
bottom of the base.
14
Connecting
Attaching the speakers
to the unit
2
Connecting
1. Connect the wires to the unit.
Match each wire’s colored band to the same
colored connection terminal on the rear of the
unit. To connect the cable to the unit, press
each plastic finger pad to open the connection
terminal. Insert the wire and release the finger
pad.
Color
Speaker
Position
Grey
Rear
Rear right
Blue
Rear
Rear left
Green
Center
Center
Orange
Sub woofer
Any front position
Red
Front
Front right
White
Front
Front left
To connect the cable to the speakers, press each
plastic finger pad to open the connection terminals
on the base of each speaker. Insert the wire and
release the finger pad.
>>Caution
Connect the black stripe of each wire to the
terminals marked -(minus) and the other end
to the terminals marked + (plus).
Connect a woofer cord to the player. When
connecting a woofer cord to the player, insert
the connector until it clicks.
yy Be careful to make sure children do not put
their hands or any objects into the *speaker
duct.
*Speaker duct : A hole for plentiful bass
sound on speaker cabinet (enclosure).
yy Place the center speaker at a safe distance
from the child’s reach. Otherwise it may
result in the speaker falling down and
causing personal injury and/or property
damage.
yy The speakers contain magnet parts, so color
irregularity may occur on the TV screen or
PC monitor screen. Please use the speakers
far away from either TV screen or PC
monitor.
2. Connect the wires to the speakers.
Connect the other end of each wire to the
correct speaker according to the color coding:
yy Before using the subwoofer, remove the
protective vinyl.
Connecting
Positioning the system
The following illustration shows an example of
positioning the system. Note that the illustrations
in these instructions differ from the actual unit for
explanation purposes.
For the best possible surround sound, all the
speakers other than the subwoofer should be
placed at the same distance from the listening
B
G
A
A
A
D
Surround left speaker (L)/ Surround right
speaker (R):
Place these speakers behind your listening
position, facing slightly inwards.
Unit
F
A
Center speaker: Place the center speaker above
or below the monitor or screen.
S ubwoofer: The position of the subwoofer is
not so critical, because low bass sounds are not
highly directional. But it is better to place the
subwoofer near the front speakers. Turn it slightly
toward the center of the room to reduce the wall
reflections.
C
A
Front left speaker (L)/ Front right speaker (R):
Place the front speakers to the sides of the
monitor or screen and as flush with the screen
surface as possible.
E
A
A ABCD E F G
2
Connecting
position ( ).
15
16
Connecting
Connections to Your
TV
Make one of the following connections, depending
on the capabilities of your existing equipment.
,,Note
2
Connecting
yy Depending on your TV and other
equipment you wish to connect, there are
various ways you could connect the player.
Use only one of the connections described
in this manual.
HDMI Out Connection
If you have a HDMI TV or monitor, you can connect
it to this unit using a HDMI cable (Type A, High
Speed HDMI™ Cable).
Connect the HDMI OUT jack on the unit to the
HDMI IN jack on a HDMI compatible TV or monitor.
Set the TV’s source to HDMI (refer to TV’s Owner’s
manual).
Unit
yy Please refer to the manuals of your TV,
Stereo System or other devices as necessary
to make the best connections.
>>Caution
yy Make sure the unit is connected directly
to the TV. Tune the TV to the correct video
input channel.
TV
yy Do not connect your player via your VCR.
The image could be distorted by the copy
protection system.
,,Tip
yy You can fully enjoy digital audio and video
signals together with this HDMI connection.
yy When you use HDMI connection, you can
change the resolution for the HDMI output.
(Refer to “Resolution Setting” on page 18.)
>>Caution
yy Changing the resolution when the
connection has already been established
may result in malfunctions. To solve the
problem, turn off the unit and then turn it
on again.
yy When the HDMI connection with HDCP is
not verified, TV screen is changed to black
or green screen or the snow noise may
occur on the screen. In this case, check the
HDMI connection, or disconnect the HDMI
cable.
Connecting
,,Note
yy If a connected HDMI device does not accept
the audio output of the unit, the HDMI
device’s audio sound may be distorted or
may not output.
yy When you connect a HDMI or DVI
compatible device make sure of the
following:
- The connected device’s video input is set
correctly for this unit.
- The connected device is compatible with
720 x 480i (or 576i), 720 x 480p (or 576p),
1280 x 720p, 1920 x 1080i or 1920 x 1080p
video input.
,,Note
Depending on the disc type or playing status,
some SIMPLINK operation may differ from your
purpose or not work.
Video Connection
Connect the VIDEO OUT jack on the unit to the
video in jack on the TV using a video cable.
You can hear the sound through the system’s
speakers.
Unit
yy Not all HDCP-compatible HDMI or DVI
devices will work with this unit.
- The picture will not be displayed properly
with non-HDCP device.
- This unit does not playback and TV screen
is changed to black or green screen or the
snow noise may occur on the screen.
yy If there is noise or lines on the screen, please
check the HDMI cable and use a higher
version cable than High Speed HDMI™
Cable.
TV
What is SIMPLINK?
Some functions of this unit are controlled by the
TV’s remote control when this unit and LG TV’s with
SIMPLINK are connected through HDMI connection.
Controllable functions by LG TV’s remote control;
Play, Pause, Scan, Skip, Stop, Power Off, etc.
Refer to the TV owner’s manual for the details of
SIMPLINK function.
LG TV’s with SIMPLINK function has the logo as
shown above.
Yellow
2
Connecting
- Try switching off the HDMI/DVI device
and this unit. Next, switch on the HDMI/
DVI device and leave it for around 30
seconds, then switch on this unit.
17
18
Connecting
Resolution Setting
The unit provides several output resolutions for
HDMI OUT.
You can change the resolution using [Setup] menu.
1.Press n HOME.
2.Use A/D to select the [Setup] and press b
ENTER. The [Setup] menu appears.
2
Video Output
Resolution
Displayed resolution in display window and
outputted resolution may different according to
connection type.
[HDMI OUT] : 1080p, 1080i, 720p and 480p (or
576p) and 480i (or 576i)
[VIDEO OUT] : 480i (or 576i)
Connecting
3.Use W/S to select [Display] option then press
D to move to the second level.
4.Use W/S to select the [Resolution] option
then press D to move to the third level.
5.Use W/S to select the desired resolution then
press b ENTER to confirm your selection.
,,Note
If your TV does not accept the resolution you
have set on the player, you can set resolution
to 480p (or 576p) as follows:
Press Z STOP for more than 5 seconds.
Connecting
Optional Equipment
Connection
19
AUDIO (PORT. IN) In
Connection
Connect an output of portable device (MP3 or PMP
etc.) to the AUDIO (PORT. IN) input connector.
AUX In Connection
Connect an Output of auxiliary device to the AUX
(L/R) INPUT Connector.
2
Connecting
Unit
MP3 player, etc...
Listening to music from your
portable player or external
device
The unit can be used to play the music from many
types of portable player or external devices.
To the audio output jacks
of your component
(TV, VCR, etc.)
,,Note
1. Connect the portable player to the
PORT. IN (PORTABLE IN) connector of the unit.
Red
White
If your TV has only one output for audio
(mono), connect it to the left (white) audio jack
on the unit.
Or
Connect the external device to the AUX (L/R)
INPUT connector of the unit.
2. Turn the power on by pressing 1/! (POWER).
3. Select the PORTABLE or AUX function by
pressing P RADIO&INPUT.
4. Turn on the portable player or external device
and start it playing.
20 Connecting
USB Connection
Compatible USB Devices
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the unit.
yy MP3 Player : Flash type MP3 player.
yy USB Flash Drive :Devices that support USB2.0 or
USB1.1.
yy The USB function of this unit does not support
some USB devices.
USB device requirement
2
Connecting
yy Devices which require additional program
installation connected to a computer, are not
supported.
yy Do not extract the USB device while in operation.
,,Note
Removing the USB Device from the unit.
1. Choose a different function mode or press
Z STOP twice in a row.
2. Remove the USB device from the unit.
yy For a large capacity USB, it may take longer than
a few minute to be searched.
yy To prevent data loss, back up all data.
yy If you use a USB extension cable or USB hub, the
USB device is not recognized.
yy Using NTFS file system is not supported. (Only
FAT(16/32) file system is supported.)
yy This unit is not supported when the total
number of files is 1000 or more.
yy External HDD, Card readers, Locked devices, or hard type usb devices are not supported.
yy USB port of the unit cannot be connected to PC.
The unit can not be used as a storage device.
yy Some USB may not work with this unit.
Connecting
OPTICAL In connection
Connect an optical output of Unit (or Digital Device
etc) to the OPTICAL IN connector.
21
Home theater speaker ez
setup
Listen to sound from TV, DVD and Digital Device
with 5.1(2.1 or 2)ch mode. Even in power off
mode, if you press OPTICAL, then power is on and
automatically changed to AUX OPT mode.
1. Connect the unit’s OPTICAL IN jack to jack on
optical out of your TV (or Digital Device etc.).
3. Listen sound with 5.1(2.1 or 2)ch speaker.
4. To escape from AUX OPT by using the OPTICAL.
Function is retuned to previous one.
To the digital
optical output jack
of your component
2
Connecting
2. Select the AUX OPT by using the OPTICAL
to select the AUX OPT directly.
22 Connecting
Antenna Connection
Connect the supplied FM antenna for listening to
the radio.
Connect the FM Wire antenna to the FM antenna
connector.
2
Connecting
,,Note
Be sure to fully extend the FM wire antenna.
System Setting 23
Adjust the setup
settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
To display and exit the Setup
menu
1.Press n HOME.
Displays the [Home Menu].
You can also set a language for the subtitles and
the Setup menu, among other things. For details on
each Setup menu item, see pages 23 to 27.
OSD Initial language settings
- Optional
1.Press 1 (POWER) to turn the unit on. The
language setup menu will appear on the screen.
3.Press b ENTER.
Displays the [Setup].
4.Press n HOME or x RETURN to exit in the
[Setup] Menu.
About help menu for Setup
Menu
Buttons
Operation
WS
Moving to another
menu.
a
Move
A
Moving to previous
level.
d
Move
D
Moving to next
level or selecting
menu.
x RETURN
To exit the [Setup]
menu or [ 5.1
Speaker Setup].
b ENTER
To confirm menu.
ws
Move
x
2.Use WSAD to select a language then press
b ENTER.
The confirm menu will appear.
3.Use AD to select the [Enter] then press b
ENTER to finish the language setup.
Close
b
Select
3
System Setting
During the first use of this unit, the initial language
setup menu appears on your TV screen. You must
complete initial language selection before using
the unit. English will be selected as the initial
language.
2. Select an [Setup] by using AD.
24 System Setting
Language
Menu Language
Select a language for the Setup menu and then on
screen display.
Disc Audio / Disc Subtitle / Disc
Menu
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
[Original]
3
Refers to the original language in which the
disc was recorded.
System Setting
[Other]
To select another language, press numeric
buttons and then b ENTER to enter the
corresponding 4-digit number according to
the language code list on the page 40. If you
enter the wrong language code, press CLEAR.
[Off (for Disc Subtitle)]
Turn off Subtitle.
[Panscan]
Automatically displays the wide picture on the
entire screen and cuts off the portions that do
not fit. (If the disc/file is not compatible with
Pan Scan, the picture is displayed at Letterbox
ratio.)
Resolution
Sets the output resolution of HDMI video signal.
Refer to “Resolution Setting” for details about the
resolution (page 18).
[Auto]
If the HDMI OUT jack is connected to
TVs providing display information (EDID),
automatically selects the resolution best suited
to the connected TV. If VIDEO OUT is only
connected, this changes the resolution to 480i
(or 576i) as default resolution.
[1080p]
Outputs 1080 lines of progressive video.
[1080i]
Outputs 1080 lines of interlaced video.
Display
[720p]
TV Aspect
[480p (or 576p)]
Select which screen aspect to use based on the
shape of your TV screen.
Outputs 480 (or 576) lines of progressive video.
[4:3]
Select when a standard 4:3 TV is connected.
[16:9]
Select when a 16:9 wide TV is connected.
Display Mode
The Display Mode setting works only when the TV
Aspect mode is set to 4:3.
[Letterbox]
Displays a wide picture with bands on the
upper and lower portions of the screen.
Outputs 720 lines of progressive video.
[480i (or 576i)]
Outputs 480 (or (576) lines of interlaced video.
System Setting 25
Audio
5.1 Speaker Setup
Make the following settings for the built-in 5.1
channel surround decoder.
[Speaker]
Select a speaker that you want to adjust.
,,Note
Certain speaker settings are prohibited by the
Dolby Digital licensing agreement.
1. Select [5.1 Speaker Setup] on the [Audio] menu.
2.Press b ENTER.
The [5.1 SPEAKER] appears.
[Size]
Since the speaker settings are fixed, you cannot
change the settings.
[Volume]
Adjust the output level of each speaker.
[Distance]
3.Use AD to select the desired speaker.
4. Adjust options using WSAD buttons.
5. Returns to the previous menu by pressing x
RETURN.
[Speaker Test Start]
Select [Speaker Test Start] by using the WS
and press b ENTER. Press b ENTER again to
stop. Adjust the volume to match the volume
of test signals memorized in the system.
3
System Setting
Adjust the distance between each speaker and
the listening position.
26 System Setting
DRC (Dynamic Range Control)
Lock (Parental Control)
Make the sound clear when the volume is turned
down (Dolby Digital only). Set to [On] for this effect.
Initial Setting the Area Code:
Vocal
When you use this unit for the first time, you have
to set the Area Code.
Select [On] to mix karaoke channels into normal
stereo.
1. Select the [Lock] menu and then press D.
This function is effective for multi-channel karaoke
DVDs only.
HD AV Sync
3
System Setting
Sometimes Digital TV encounters a delay between
picture and sound. If this happens you can
compensate by setting a delay on the sound so
that it effectively ‘waits’ for the picture to arrive:
this is called HD AV Sync. Use WS (on the remote
control) to scroll up and down through the delay
amount, which you can set at anything between 0
and 300ms.
Semi Karaoke
When a chapter/ title/ track is fully finished, this
function shows the score in the screen with a
fanfare sound.
[On]
When you finished singing a score will appear
on the screen.
[Off]
Fanfare and score do not appears on the
screen.
,,Note
VD, DVD Karaoke discs with more than
yy D
2 tracks are available discs for the this
function.
hen you watch movies, “off ” the Semi
yy W
Karaoke at the SETUP menu or enjoy it
without connecting the MIC if the fanfare or
score appears during changing a chapter.
yy This function operate on the DVD/CD mode.
yy T he Semi Karaoke function is available only
when a microphone is connected.
yy If you do not use the microphone, turn
down the volume and disconnect the
microphone.
2.Press D.
To access the [Lock] options, you must input the
password you have created. Input a password
and press b ENTER. Enter it again and press b
ENTER to verify. If you make a mistake before
pressing b ENTER, press CLEAR.
3. Select the first character using WS buttons.
4.Press b ENTER and select the second character
using WS buttons.
5.Press b ENTER to confirm your Area code
selection.
Rating
Blocks playback of rated DVDs based on their
contents. Not all discs are rated.
1. Select [Rating] on the [Lock] menu then press
D.
2. Input a password and press b ENTER.
3. Select a rating from 1 to 8 using the WS
buttons.
[Rating 1-8]
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
[Unlock]
If you select unlock, parental control is not
active and the disc plays in full.
4.Press b ENTER to confirm your rating selection.
System Setting 27
Password
Others
You can enter or change password.
1. Select [Password] on the [Lock] menu and then
press D.
2.Press b ENTER.
3. Input a password and press b ENTER.
To change the password, press b ENTER when
the [Change] option is highlighted. Input a
password and press b ENTER. Enter it again
and press b ENTER to verify.
4.Press n HOME to exit the menu.
,,Note
If you forget your password, you can clear it
using the following steps:
2. Input the 6-digit number “210499” and
press b ENTER. The password is cleared.
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX, LLC, a subsidiary of Rovi
Corporation. This is an official DivX Certified®
device that has passed rigorous testing to verify
that it plays DivX video. Visit divx.com for more
information and software tools to convert your files
into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to play
purchased DivX Video-on-Demand (VOD) movies.
To obtain your registration code, locate the DivX
VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete
your registration.
[Register]
Displays the registration code of your player.
[Deregister]
Area Code
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list
on page 39.
1. Select [Area Code] on the [Lock] menu then
press D.
2. Input a password and press b ENTER.
3. Select the first character using WS buttons.
4.Press b ENTER and select the second character
using WS buttons.
5.Press b ENTER to confirm your Area code
selection.
Deactivate your player and display the
deactivation code.
,,Note
All the downloaded videos from DivX VOD can
only be played back on this unit.
3
System Setting
1. Select the [Setup] menu on the [Home
Menu].
DivX(R) VOD
28 Operating
Using the Home Menu
Basic Operations
1.Press n HOME.
Displays the [Home Menu].
1. Insert the disc by using the B OPEN/CLOSE or
connect the USB device to the USB port.
2.Press n HOME.
Displays the [Home Menu].
2. Select an option by using AD.
3.Press b ENTER then selected option menu.
3. Select an option by using AD.
If you select the [Movie], [Photo] or [Music]
option when you connect up to two devices,
it appears as belows. Select a media then press
b ENTER.
[Music] – Displays [MUSIC] menu.
[Movie] – Start video media’s playback or displays
the [MOVIE] menu.
[Photo] – Displays [PHOTO] menu.
[Setup] – Displays the [Setup] menu.
,,Note
4
Operating
You can not select the [Music], [Movie] or
[Photo] option when the USB device is not
connected or a disc is not inserted.
4.Press b ENTER then selected option menu.
,,Note
yy For the most Audio CD and DVD-ROM discs,
playback starts automatically.
yy The unit plays only music file contained in
the USB storage device or disc automatically.
Operating 29
To
Stop
Do this
Playback
Press d PLAY, MONO/
STEREO.
Pause
Press M PAUSE/STEP.
Press M PAUSE/STEP
Frame-byrepeatedly to play title FrameFrame playback
by-Frame. (DVD, DivX only)
During playback, press C/
V SKIP to go to the next
Skipping to the chapter/ track/ file or to
next/ previous return to the beginning of the
chapter/ track/ current chapter/ track/ file.
file
Press C SKIP twice briefly
to step back to the previous
chapter/ track/ file.
Playing
repeatedly or
randomly
During playback, press c/
v SCAN repeatedly to
select the required scan speed.
To return to normal speed,
press d PLAY, MONO/
STEREO.
Press h REPEAT repeatedly,
and the current title, chapter
or track will be played back
repeatedly or randomly.
- DVD : Chapter/ Title/ Off
- DivX : Title/ All/ Off
- Audio CD/ MP3/ WMA : Track/
All/ Random/ Off
Slowing down
the playing
speed
In the pause mode, press
c/v SCAN to select the
required speed. (DVD, DivX
only) The DivX file cannot be
slow down reverse playback.
Displaying Disc Information
on-screen
You can display various information about the disc
loaded on-screen.
1.Press m INFO/DISPLAY to show various
playback information.
The displayed items differ depending on the
disc type or playing status.
2. You can select an item by pressing WS and
change or select the setting by pressing AD.
Title – Current title number/ total number of titles.
Chapter – C
urrent chapter number/ total number
of chapters.
Time – Elapsed playing time.
Audio – Selected audio language or channel.
Subtitle – Selected subtitle.
Angle – S elected angle/ total number of angles.
,,Note
If any button is not pressed for a few seconds,
the on-screen display disappears.
4
Operating
Locating a
point quickly by
playing a file in
fast forward or
fast reverse
Other Operations
Press Z STOP.
30 Operating
To display the DVD Menu
r
When you play a DVD which contains several menu,
you can select the menu you want using the Menu.
1.Press DISC MENU.
The disc’s menu appears.
2. Select the menu by using WSAD.
3.Press d PLAY, MONO/STEREO to confirm.
4.Press b ENTER to confirm. Playback starts from
the selected time.
To display the DVD title
Resume playback
r
When you play a DVD which contains several title,
you can select the title you want using the Menu.
1.Press TITLE.
The disc’s title appears.
2. Select the menu by pressing WSAD.
4
3. Input the required start time in hours, minutes,
and seconds from left to right. If you enter the
wrong numbers, press CLEAR to remove the
numbers you entered. Then input the correct
numbers.
For example, to find a scene at 1 hour, 10
minutes, and 20 seconds, enter “11020” by using
numerical buttons.
3.Press d PLAY, MONO/STEREO to confirm.
Operating
1.5 times speed playback
r
The 1.5 speed allows you to watch the pictures and
listen to the sound quicker than playing at a normal
speed.
1. During playback, press d PLAY, MONO/
STEREO to play at 1.5 times speed. “dX1.5”
appears on the screen.
2.Press d PLAY, MONO/STEREO again to exit.
Screen Saver
The screen saver appears when you leave the unit
in Stop mode for about five minutes.
Starting play from selected
time
ry
To start playing at any chosen time on the file or
title.
1.Press m INFO/DISPLAY during playback.
2.Press WS to select the time clock icon and
“--:--:--” appears.
ryut
The unit records the point where you pressed the
Z STOP depending on the disc.
If “MZ (Resume Stop)” appears on the screen briefly,
press d PLAY, MONO/STEREO to resume playback
(from the scene point).
If you press Z STOP twice or unload the disc,
“Z”(Complete Stop) appears on the screen. The
unit will clear the stopped point.
,,Note
yy The resume point may be cleared when a
button is pressed (for example; 1 (POWER),
B OPEN/CLOSE, etc).
yy This function may not work on some disc or
title/track.
Changing subtitle code page
y
If the subtitle is not displayed properly, you can
change the subtitle code page to view the subtitle
file properly.
1. During playback, press m INFO/DISPLAY to
display the On-Screen display.
2.Use WS to select the [Code Page] option.
3.Use AD to select desired code option.
4.Press x RETURN to exit the On-Screen display.
Operating
Marked Playback
ut
The mark function enables you to store your
favourite files from any disc or USB device in the
unit memory.
1. Select [Music] on the [Home Menu].
Returning to the upper folder.
(MP3/ WMA only)
File information will be displayed
according to the ID3TAG information
on the appropriate music file. (MP3
only)
31
To delete a Marker
1.Use WS to select the track that you wish to erase
from the marked file.
2.Press MARKER.
To delete all Markers
Use WSAD to select [Deselect All] then press b
ENTER in program edit mode.
,,Note
The markers are also cleared when the disc or
USB device is removed, the unit is switched to
power off or the function is switched to others.
4
Deselecting all tracks/files.
Moving to the previous or
next file list.
2. Select a desired music on the [List] by using the
WS then press MARKER to appears the mark on
the list.
3.Press b ENTER or d PLAY, MONO/STEREO.
Displays the play mode.
4. Select the play mode by using the WS and press
b ENTER.
[Mark Play]
Marked playback.
[Current Play]
Normal playback.
,,Note
If you want to select all files on the list, select
[Select All] and press b ENTER.
Operating
Selecting all tracks/ files.
32 Operating
Viewing a PHOTO file
About help menu in the full screen
Menu
Buttons
Operation
Menu
m
INFO/
DISPLAY
Displaying the Option
menu.
a/d
Prev./ Next
A/D
Moving to another file.
i
This unit can play discs with photo files.
1. Select [Photo] on the [Home Menu] and press
b ENTER.
Moving to the previous or
next file list.
x
List
x
RETURN
Returning to the
[Photo] menu.
Options while viewing a photo
You can use various options during viewing a
photo in full screen.
1. While viewing a photo in full screen, press
m INFO/DISPLAY to display the option menu.
4
2. Select an option using WSAD.
Returning to the upper
folder.
Operating
2.Press WS to select a folder, and then press b
ENTER.
3. If you want to view a slide show, press WS
to highlight a file and press d PLAY, MONO/
STEREO.
About help menu in the [Photo] menu
Menu
Buttons
d Slide
Show
d
PLAY, MONO/
STEREO
wsad
Move
WSAD
Moving to another
file or content.
b
Select
b ENTER
Viewing a particular
file.
x
Close
x RETURN
Operation
Viewing a slide
show.
Returning to the
[Home Menu].
a
b c
de
a Current photo/ Total number of photos –
Use AD to view previous/next photo.
b Slide Show z/M– Press  ENTER to start
or pause slide show.
c Speed x3/ x2/ x1 – Use  ENTER to select
a delaying speed between photos in a slide
show.
d Rotate – Press  ENTER to rotate the photo.
e Go to list – Press  ENTER to return [Photo]
menu.
Operating 33
Sleep Timer Setting
System Select - Optional
Press SLEEP one or more times to select delay time
between 10 and 180 minutes, after the unit will
turn off.
You must select the appropriate system mode for
your TV system. Press and hold M PAUSE/STEP
for more than five seconds to be able to select a
system in the [Home Menu].
To check the remaining time, press SLEEP.
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then press
SLEEP once again while “SLEEP 10” is displayed.
,,Note
You can check the remaining time before the
Unit turns off.
Press SLEEP The remaining time appears in the
display window.
Dimmer
Press SLEEP once. The display window will be
darken by half. To cancel it, press SLEEP repeatedly
until dim off.
Press
MUTE to mute your unit.
Adjust the speaker level
settings
You can adjust the sound level of each speaker.
1.Press SPEAKER LEVEL repeatedly to select a
desired speaker to set.
2.Press VOL -/+ to adjust the sound level of the
selected speaker while the level setting memu
is displayed on the display window.
3. Repeat and adjust the sound level of the other
speakers.
VOCAL FADER
You can mute your unit in order, for example, to
answer the telephone, appears the MUTE in the
display window.
You can enjoy the function as karaoke, by reducing
singer vocal of music in the various source. (MP3/
WMA/ CD/ etc.) Press the VOCAL FADER, and
“FADE ON” will appear in display window.
Last Scene Memory
To cancel it, press VOCAL FADER again.
r
This unit memorizes last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the unit or switch
off the unit. If you load a disc that has the scene
memorized, the scene is automatically recalled.
The quality of the VOCAL FADER may be different
depending on the recording conditions of music
files.
,,Note
yy This function is available to use only when a
microphone is connected.
yy It is not available on the MONO source.
Power Resume - Optional
r
Even if the power suddenly goes out, turn on the
unit and then it plays a position where the contents
is being played. System will periodically save
current playback status.
Auto power down
This unit will be off itself to save electric consumption
in the case main unit is not connected to external
device and is not used for 20 minutes. So does
this unit after six hours since Main unit has been
connected to other device using analog input.
4
Operating
Turn off the sound temporarily
,,Note
If the USB device is connected or a disc is
inserted, this function is not operated.
34 Operating
Radio Operations
Be sure that FM antenna is connected.
(Refer to the page 22.)
Listening to the radio
1.Press P RADIO&INPUT until FM appears in
the display window.
The last received station is tuned in.
2. Press and hold TUNING (-/+) for about two
seconds until the frequency indication starts to
change, then release. Scanning stops when the
unit tunes in a station.
or
Press TUNING (-/+) repeatedly.
3. Adjust the volume by pressing VOL (-/+)
repeatedly.
4
Operating
Presetting the Radio Stations
You can preset 50 stations for FM.
Before tuning, make sure that you have turned
down the volume.
1.Press P RADIO&INPUT until FM appears in
the display window.
2. Select the desired frequency by using TUNING
(-/+).
3.Press b ENTER a preset number will flash in
the display window.
4.Press PRESET (-/+) to select the preset number
you want.
5.Press b ENTER.
The station is stored.
6. Repeat the steps 2 to 5 to store other stations.
Deleting all the saved stations
1. Press and hold CLEAR for two seconds.
“ERASE ALL” will flash up on the unit display.
2.Press CLEAR to erase all saved of the radio
stations.
Deleting a saved station
1.Press PRESET - / + to select a preset number
you want to delete.
2.Press CLEAR, the preset number will blink in the
display window.
3.Press CLEAR again, to delete the selected preset
number.
Improving poor FM reception
Press d PLAY, MONO/STEREO on the remote
control. This will change the tuner from stereo to
mono and usually improve the reception.
Operating 35
Sound adjustment
,,Note
Setting the surround mode
yy In some of surround modes, some speakers,
there’s no sound or low sound. It depends
on the mode of surround and the source of
audio, it is not defective.
This system has a number of pre-set surround
sound fields. You can select a desired sound mode
by using SOUND EFFECT.
yy You may need to reset the surround mode,
after switching the input, sometimes even
after the sound track changed.
You can change the SOUND EFFECT using AD
arrow key while the sound effect information is
displayed on.
yy This function is not operated when the
microphone is connected to the unit.
The displayed items for the equalizer maybe
different depending on sound sources and effects.
Description
NAT PLUS
The NAT PLUS is Natural Plus
sound effect. You can enjoy
the natural sound effect same
as a 5.1-channel.
NATURAL
You can enjoy comfortable
and natural sound.
POP
CLASSIC
JAZZ
ROCK
This program lends an
enthusiastic atmosphere to
the sound, giving you the
feeling you are at an actual
rock pop, jazz or classic
concert.
BASS
The BASS is Bass Blast. During
playback, reinforce the treble,
bass and surround sound
effect.
LOUDNESS
Improves the bass and treble
sound.
BYPASS
You can enjoy the sound
without equalizer effect.
You can enjoy the harmonious
P-FRONT
sound. This mode is suited
(POWER FORNT) for front-positioned speakers
-Optional
when they are all placed in a
row.
4
Operating
On Display
36 Operating
Advanced Operations
Recording to USB
You can record music or sound souce to USB device
by connecting in to the port on the unit.
yy During recording MP3/WMA, there is no
sound.
1. Connect the USB device to the unit.
yy When you stop recording during playback,
the file that has been recorded at that time
will be stored. (Except MP3/WMA files)
2. Select a mode in which you want to record.
Playback a sound source first.
3. Start the recording by pressing X REC.
4. To stop recording, press Z STOP.
[All tracks/ files recording]
Record to USB in stop or play mode.
[Program list recording]
After marking desired file(s) and you can record
it to USB (Refer to the page 31).
4
,,Note
yy You can check the recording percentage
rate for the USB record on the screen during
the recording. (Audio CD or MP3/ WMA CD
only)
It’ll be stored as follows.
Operating
Audio CD
yy Do not remove the USB device or turn off
the unit during USB recording. If does not,
an incomplete file may be made and not
deleted on PC.
yy Recording through microphones is not
available.
yy If USB recording does not work, the
message like “NO USB”, “ERROR”, “USB FULL”
or “NO REC” is displayed on the display
window.
yy Multi card reader device or external HDD
can not be used for USB recording.
yy A file is recorded by 128 Mbyte (about 2
hours) when you record for a long term.
There are recorded less than 4 files.
yy In the state CD-G, DTS disc USB record is not
operated.
MP3/ WMA
yy The files in the sub-folders are not recorded
during all track recording.
yy You may not record more than 999 files.
The other
sources (Tuner,
AUX, Portable)
yy The numbering of the recording file is
entered from the lowest number. So if you
delete some of the recording files, the next
recording file could be the lowest number
among them.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights.
5Troubleshooting
Troubleshooting 37
Troubleshooting
PROBLEM
No power
No picture
CORRECTION
Plug the power cord into the wall outlet securely.
Select the appropriate video input mode on the TV so the picture
from the unit appears on the TV screen.
Connect the video cables securely to both the TV and unit.
Select the correct input mode of the unit so you can hear the sound
from the unit.
There is little or no sound
Connect the audio cables into the connection terminals correctly.
Replace with a new audio cable.
The DVD picture quality is poor
Clean the disc using a soft cloth with outward strokes.
Insert a disc.
A DVD/CD will not play
Insert a playable disc (check the disc type, colour system and
regional code).
Place the disc with the label or printed side facing upwards.
Enter your password or change the rating level.
Clean the disc using a soft cloth with outward strokes.
Move unit and audio components further away from your TV.
Check the antenna connection and adjust its position.
Radio stations can’t be tuned in
properly
Attach an external antenna if necessary.
Tune to the station manually.
Preset some radio stations, see page 34 for details.
The remote is not pointed directly at the unit.
Point the remote directly at the unit.
The remote is too far from the unit.
Use the remote within 23 feet (7 m) of the unit.
The remote control doesn’t work
well / at all
There is an obstacle in the path between the remote control and
the unit.
Remove the obstacle.
The battery in the remote control are flat.
Replace the battery with new ones.
5
Troubleshooting
Humming noise heard while a DVD
or CD is playing
6Appendix
38 Appendix
Maintenance
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
yy Do not use volatile liquids such as insecticide
spray near the unit.
yy Wiping with strong pressure may damage the
surface.
yy Do not leave rubber or plastic products in
contact with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
6
Maintaining the Unit
Appendix
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
Notes on Discs
Handling Discs
Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints do not
get on the surface. Never stick paper or tape on the
disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center to out.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for older vinyl records.
Appendix 39
Area Code List
Choose an area code from this list.
AreaCode AreaCode AreaCode AreaCode
Afghanistan AF Fiji FJ Monaco MC Singapore SG
SK
Argentina AR Finland FI Mongolia MN Slovak Republic Australia AU France FR Morocco MA Slovenia Austria AT Germany DE Nepal NP South Africa ZA
Belgium BE Great Britain GB Netherlands NL South Korea KR
Bhutan BT Greece GR Antilles AN Spain ES
Bolivia BO Greenland GL New Zealand NZ Sri Lanka LK
SI
Brazil BR Hong Kong HK Nigeria NG Sweden SE
Cambodia KH Hungary HU Norway NO Switzerland CH
Canada CA India IN Oman OM Taiwan TW
CL Indonesia ID Pakistan Chile PK Thailand TH
China CN Israel IL Panama PA Turkey TR
Colombia CO Italy IT Paraguay PY Uganda UG
Congo CG Jamaica JM Philippines PH Ukraine UA
Costa Rica CR Japan JP Poland PL United States US
Croatia HR Kenya KE Portugal PT Uruguay UY
Czech Republic CZ Kuwait KW Romania RO Uzbekistan UZ
Denmark DK Libya Ecuador EC Luxembourg Egypt EG Malaysia El Salvador SV Maldives MY Saudi Arabia MV Senegal Ethiopia ET Mexico MX
LY Russian
LU Federation Vietnam RU Zimbabwe SA
SN
VN
ZW
6
Appendix
40 Appendix
Language code List
Use this list to input your desired language for the following initial settings: [Disc Audio],
[Disc Subtitle] and [Disc Menu].
6
Appendix
LanguageCode
LanguageCode
LanguageCode
LanguageCode
Afar 6565
French 7082
Lithuanian 7684
Sindhi 8368
Afrikaans 6570
Frisian 7089
Macedonian 7775
Singhalese 8373
Albanian 8381
Galician 7176
Malagasy 7771
Slovak 8375
Ameharic 6577
Georgian 7565
Malay 7783
Slovenian 8376
Arabic 6582
German 6869
Malayalam 7776
Spanish 6983
Armenian 7289
Greek 6976
Maori 7773
Sudanese 8385
Assamese 6583
Greenlandic 7576
Marathi 7782
Swahili 8387
Aymara 6588
Guarani 7178
Moldavian 7779
Swedish 8386
Azerbaijani 6590
Gujarati 7185
Mongolian 7778
Tagalog 8476
Bashkir 6665
Hausa 7265
Nauru7865
Tajik 8471
Basque 6985
Hebrew 7387
Nepali 7869
Tamil 8465
Bengali; Bangla 6678
Hindi 7273
Norwegian 7879
Telugu 8469
Bhutani 6890
Hungarian 7285
Oriya 7982
Thai 8472
Bihari 6672
Icelandic 7383
Panjabi 8065
Tonga 8479
Breton 6682
Indonesian 7378
Pashto, Pushto 8083
Turkish 8482
Bulgarian 6671
Interlingua 7365
Persian 7065
Turkmen 8475
Burmese 7789
Irish 7165
Polish 8076
Twi 8487
Byelorussian 6669
Italian 7384
Portuguese 8084
Ukrainian 8575
Chinese 9072
Japanese 7465
Quechua 8185
Urdu 8582
Croatian 7282
Kannada 7578
Rhaeto-Romance 8277
Uzbek 8590
Czech 6783
Kashmiri 7583
Rumanian 8279
Vietnamese 8673
Danish 6865
Kazakh 7575
Russian 8285
Volapük 8679
Dutch 7876
Kirghiz 7589
Samoan 8377
Welsh 6789
English 6978
Korean 7579
Sanskrit 8365
Wolof 8779
Esperanto 6979
Kurdish 7585
Scots Gaelic 7168
Xhosa 8872
7473
Estonian 6984
Laothian 7679
Serbian 8382
Yiddish Faroese 7079
Latin 7665
Serbo-Croatian 8372
Yoruba 8979
Fiji 7074
Latvian, Lettish 7686
Shona 8378
Zulu 9085
Finnish 7073
Lingala 7678
Appendix
41
Trademarks and Licenses
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
DivX®, DivX Certified® and associated logos are
trademarks of Rovi Corporation or its subsidiaries
and are used under license.
Covered by one or more of the following U.S.
patents: 7,295,673; 7,460,668; 7,515,710; 7,519,274
6
Appendix
42 Appendix
Specifications
General
Power requirements
Refer to main label.
Power consumption
Refer to main label.
Dimensions (W x H x D)
(360 x 60.5 x 299) mm without foot
Net Weight (Approx.)
2.66 kg
Operating temperature
41 °F to 95 °F (5 °C to 35 °C)
Operating humidity
5 % to 90 %
Bus Power Supply
5 V 0 500 mA
Inputs/ Outputs
VIDEO OUT
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
HDMI OUT (video/audio)
19 pin (Type A, HDMI™ Connector )
ANALOG AUDIO IN
2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
DIGITAL IN (OPTICAL)
3 V (p-p), Optical jack x 1
PORT. IN
0.5 Vrms (3.5 mm stereo jack)
Amplifier
Stereo mode
Surround mode
6
167 W + 167 W (3 Ω at 1kHz)
Front
167 W + 167 W (3 Ω at 1 kHz)
Center
167 W (3 Ω at 1 kHz)
Surround
167 W + 167 W (3 Ω at 1 kHz))
Subwoofer
167 W (3 Ω at 60 Hz)
Appendix
Tuner
FM Tuning Range
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
Appendix 43
Front Speaker
DH6340H (S64H1-S)
DH6340P (S64H1-S)
Type
2 way 3 speaker
2 way 3 speaker
Impedance
3Ω
3Ω
Rated Input Power
167 W
167 W
Max. Input Power
334 W
334 W
Net Dimensions (W x H x D)
(202 x 470.5 x 202) mm
(202 x 470.5 x 202) mm
Net Weight
1.6 kg
1.6 kg
Rear Speaker
DH6340H (S64H1-S)
DH6340P (S64B1-S)
Type
2 way 3 speaker
1 way 1 speaker
Impedance Rated
3Ω
3Ω
Rated Input Power
167 W
167 W
Max. Input Power
334 W
334 W
Net Dimensions (W x H x D)
(202 x 470.5 x 202) mm
(100.5 x 203 x 97.5) mm
Net Weight
1.6 kg
0.7 kg
Centre Speaker
DH6340H (S64H1-C)
DH6340P (S64H1-C)
Type
2 way 3 speaker
2 way 3 speaker
Impedance
3Ω
3Ω
Rated Input Power
167 W
167 W
Max. Input Power
334 W
334 W
Net Dimensions (W x H x D)
(342.5 x 86 x 87) mm
(342.5 x 86 x 87) mm
Net Weight
1.2 kg
1.2 kg
DH6340H (S64H1-W)
DH6340P (S64H1-W)
1 Way 1 Speaker
1 Way 1 Speaker
Impedance
3Ω
3Ω
Rated Input Power
167 W
167 W
Max. Input Power
334 W
334 W
Net Dimensions (W x H x D)
(240 x 360 x 391) mm
(240 x 360 x 391) mm
Net Weight
6.6 kg
6.6 kg
yy Design and specifications are subject to change without notice.
6
Appendix
Passive Subwoofer
Type
Download PDF