LG | DM8360 | LG DM8360 Owner’s Manual

OWNER’S MANUAL
DVD MINI
HI-FI SYSTEM
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
DM8360 (DM8360, DMS8360F)
www.lg.com
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral
triangle is intended to alert the
user to the presence of uninsulated
dangerous voltage within the
product’s enclosure that may be of
sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, should be placed on the
apparatus.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not use high voltage products around
this product. (ex. Electrical swatter) This product may
malfunction due to electrical shock.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance, contact
an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure. To prevent
direct exposure to laser beam, do not try to open the
enclosure.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of
the product and to protect it from over heating.
The openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product should not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
NOTICE: For safety marking information including
product identification and supply ratings, please refer
to the main label on the bottom or the other surface
of the product.
Getting Started
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a
dedicated circuit;
The Power Plug is the disconnecting device. In case
of an emergency, the Power Plug must remain readily
accessible.
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the battery
from the equipment: Remove the old battery or
battery pack, follow the steps in reverse order than
the assembly. To prevent contamination of the
environment and bring on possible threat to human
and animal health, the old battery or the battery
put it in the appropriate container at designated
collection points. Do not dispose of batteries or
battery together with other waste. It is recommended
that you use local, free reimbursement systems
batteries and accumulators. The battery shall not be
exposed to excessive heat such as sunshine, fire or
the like.
Caution: No naked flame sources, such as lighted
candles, should be placed on the apparatus.
Symbols
~
0
Refers to alternating current(AC).
Refers to direct current(DC).
Refers to class II equipment.
1
Refers to stand-by.
!
Refers to “ON” (power).
Refers to dangerous voltage.
1
Getting Started
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact
replacement part by an authorized service center.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention to
plugs, wall outlets, and the point where the cord exits
the appliance.
3
4
Table of Contents
Table of Contents
1
Getting Started
2Connecting
2
6
6
6
6
7
7
7
7
7
8
8
8
9
10
11
Safety Information
Unique Features
Introduction
– Playable Discs
– About the “7” Symbol Display
– Symbols Used in this Manual
– Regional Codes
Playable file Requirement
– Music file requirement
– Photo file requirement
– Video file requirement
– Compatible USB Devices
– USB device requirement
Remote control
Front panel
Rear panel
12
13
13
14
15
15
15
16
16
17
Connecting to speakers
Connections to Your TV
– HDMI Out Connection
– Resolution Setting
Optional Equipment Connection
– AUX IN Connection
– AUX OUT Connection
– PORT. IN Connection
– USB Connection
– Antenna Connection
3
System Setting
18
18
18
19
19
20
20
Adjust the setup settings
– OSD Initial language settings - Optional
– To display and exit the Setup menu
– Language
– Display
– Audio
– Lock (Parental Control)
Table of Contents
1
4Operating
22
22
24
24
25
25
27
27
27
27
27
27
28
28
28
29
29
29
29
29
29
29
29
30
30
31
32
Using the Home Menu
Basic Operations
Playback Effect
– AUTO DJ
Using BLUETOOTH® wireless technology
– Listening to music stored on the Bluetooth
devices
Radio Operations
– Listening to the radio
– Improving poor FM reception
– Presetting the Radio Stations
– Deleting all the saved stations
– Deleting a saved station
Sound adjustment
– Setting the sound mode
– Setting the USER EQ
Advanced Operations
– Displaying Disc Information on-screen
– To display the DVD Menu
– To display the DVD title
– 1.5 times speed playback
– Screen Saver
– Starting play from selected time
– Resume playback
– Changing subtitle code page
– Marked Playback
– Viewing a PHOTO file
– Recording to USB
5
33
33
33
33
33
33
33
34
34
34
35
35
36
36
37
37
38
Other Operations
– Sleep Timer Setting
– Dimmer
– Last Scene Memory
– Power Resume - Optional
– System Select - Optional
– Turn off the sound temporarily
– CHILDSAFE Mode
– DEMO
– VOICE CANCELLER
– Using Microphone
Setting the Clock
– Using your player as an alarm clock
Auto power down
– AUTO POWER On
– Auto function change
LG Sound Sync
2
3
4
5
5Troubleshooting
39
Troubleshooting
6Appendix
41
41
42
43
44
45
45
45
46
47
Controlling a TV with the Supplied Remote
Control
– Setting up the remote to control your TV
Area Code List
Language code List
Trademarks and Licenses
Maintenance
– Notes on Discs
– Handling the Unit
General specifications
Speakers specifications
6
6
1
Getting Started
Unique Features
Introduction
Bluetooth®
Playable Discs
Getting Started
Listens to music stored on your Bluetooth device.
Portable In
Listens to music from your portable device. (MP3,
Notebook, etc.)
AUTO DJ
Blends the end of one song into the beginning of
another for seamless playback.
USB Direct Recording
Records music to your USB device.
This unit plays DVD±R/RW and CD-R/RW that
contains audio titles, MP3, WMA and/or JPEG files.
Some DVD±RW/DVD±R or CD-RW/CD-R cannot be
played on this unit due to the recording quality or
physical condition of the disc, or the characteristics of
the recording device and authoring software.
DVD-VIDEO (8 cm/12 cm disc)
Discs such as movies that can be
purchased or rented.
DVD±R (8 cm/12 cm disc)
Video mode and finalized only.
LG Sound Sync
DVD-RW (8 cm/12 cm disc)
Controls volume level of this unit by the remote
control of your LG TV that is compatible with LG
Sound Sync.
Video mode and finalized only.
Full HD up-scaling
Views Full HD picture quality with simple setup.
DVD+R: Video mode only
Supports the double layer disc also.
DVD+RW (8 cm/12 cm disc)
Video mode and finalized only.
Audio CD: Music CDs or CD-R/CDRW in music CD format that can be
purchased.
About the “7” Symbol Display
“7” may appear on your TV display during operation
and indicates that the function explained in this
owner’s manual is not available on that specific
media.
Getting Started
Symbols Used in this Manual
DVD-Video, DVD±R/RW in Video
mode or VR mode and finalized
t
Audio CDs
Playable file
Requirement
1
Music file requirement
y
Video files contained in the USB/
Disc
u
Audio files contained in the USB/
Disc
yy Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
i
Photo files contained in the USB/
Disc
yy Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
,,Note
Indicates special notes and operating features.
,,Tip
Indicates tip and hints for making the task easier.
>>Caution
Indicates cautions for preventing possible damages
from abuse.
Regional Codes
This unit has a regional code printed on the rear of
the unit. This unit can play only DVD discs labeled
same as the rear of the unit or “ALL”.
yy Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your unit’s regional code or
the disc cannot play.
yy If you try to play a DVD with a different regional
code from your unit, the message “Check Regional
Code” appears on the TV screen.
MP3/WMA file compatibility with this unit is limited
as follows.
yy Support Version : v2, v7, v8, v9
yy Maximum files : Under 999
yy File extensions : “.mp3”/ “.wma”
yy Certain MP3/WMA files may not be played
depending on the type or format of the file.
yy CD-ROM file format : ISO 9660/ JOLIET
yy We recommend that you use Easy-CD Creator,
which creates an ISO 9660 file system.
The DTS is not supported. In case of DTS audio
format, audio is not output.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot use
it on LG players.
(Mastered/Live File System : Disc format system for
Windows Vista)
Photo file requirement
Photo file compatibility with this unit is limited as
follows :
yy Max pixel in width : 2760 x 2048 pixel
yy Maximum files : Under 999
yy Some discs may not operate due to a different
recording format or the condition of disc.
yy File extensions: “.jpg”
yy CD-ROM file format : ISO9660/ JOLIET
Getting Started
r
7
8
1
Getting Started
Video file requirement
Compatible USB Devices
Video file compatibility with this unit is limited as
follows:
yy MP3 Player : Flash type MP3 player.
Getting Started
yy Available resolution: within 720 x 576 (W x H)
pixels.
yy The file name of the Video subtitle should be
entered within 45 characters.
yy If there is impossible code to express in the Video
file, it may be displayed as “ _ “ mark on the display.
yy Frame rate : less than 30 fps.
yy If the video and audio structure of recorded files is
not interleaved, either video or audio is outputted.
yy Playable Video file : “.avi”, “.mpg”, “.mpeg”
yy Playable Subtitle format : SubRip (*.srt/ *.txt),
SAMI (*.smi), SubStation Alpha (*.ssa/ *.txt),
MicroDVD (*.sub/ *.txt), SubViewer 2.0 (*.sub/
*.txt), Vobsub (*.sub)
yy Playable Codec format :
“Xvid”, “MPEG-1”, “MPEG-2”
yy Playable Audio format : “AC3”, “PCM”, “MP3”,
“WMA”,
yy Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
yy Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
yy For Discs formatted in Live file system, you can not
it on this unit.
yy If the name of movie file is different from that of
the subtitle file, during playback of a Video file,
subtitle may not be display.
yy If you play a Xvid file differ from Xvid spec, it may
not operate normally.
yy If you play GMC video file which is more than
1-warp point, video playback screen will not
smooth.
yy USB Flash Drive :
Devices that support USB2.0 or USB1.1.
yy The USB function of this unit does not support all
USB devices.
USB device requirement
yy Devices which require additional program
installation when you have connected it to a
computer, are not supported.
yy Do not extract the USB device while in operation.
yy For a large capacity USB, it may take longer than a
few minute to be searched.
yy To prevent data loss, back up all data.
yy If you use a USB extension cable or USB hub, the
USB device is not recognized.
yy Using NTFS file system is not supported. (Only
FAT(16/ 32) file system is supported.)
yy This unit is not supported when the total number
of files is 1,000 or more.
yy External HDD, Card readers, Locked devices, or
hard type USB devices are not supported.
yy USB port of the unit cannot be connected to PC.
The unit cannot be used as a storage device.
yy Some USB may not work with this unit.
Getting Started
Remote control
B (Open/Close) : Opens and closes
the disc tray.
TITLE: If the current DVD title has
a menu, the title menu appears
on the screen. Otherwise, the disc
menu may not appear.
n (Home) : Displays the [Home
Menu].
DISC MENU : Accesses the menu
on a DVD disc.
• • • • • • • • • b• • • • • • • •
W/S/A/D (up/ down/ left/
right) : Used to navigate on-screen
displays.
PRESET +/- : Selects programme
of Radio.
A(R
03
)
• • • • • • • • • a• • • • • • • •
F (Function) : Selects the function
and input source.
MARKER : Marks play list.
1 (Standby/On) : Switches the
unit ON or OFF.
1
VOL -/+ (Volume) : Adjusts speaker
volume.
AUTO DJ : Selects the AUTO DJ
mode. (For more information refer
to page 24)
(Mute) : Mutes the sound.
• • • • • • • • • e• • • • • • • •
0-9 numerical buttons : Selects
numbered options in a menu.
REPEAT : Selects a play mode.
(Repeat/ Random)
CLEAR : Removes a number when
setting the password.
• • • • • • • • • f• • • • • • • •
b OK : Acknowledges menu
selection.
Presetting the radio stations.
MIC VOL -/+ (Microphone Volume)
: Adjusts microphone volume.
m INFO/DISPLAY : Accesses
On-Screen Display.
See the name of connected
Bluetooth device in Bluetooth
mode.
Z (Stop) : Stops playback.
d (Play) : Starts playback.
M (Pause) : Pauses playback.
Remove the battery cover on the
rear of the remote control, and
insert the battery with 4 and 5
matched correctly.
SOUND EFFECT : Selects a sound
effect mode.
TV Control buttons: See page 41.
• • • • • • • • • c• • • • • • • •
AA
REGION EQ : Chooses sound
impressions.
TUNING +/- : Tunes in the desired
radio station.
x BACK : Moves backwards in
the menu or exits the setup menu.
Replacement of battery
• • • • • • • • • d• • • • • • • •
Getting Started
SLEEP : Sets the System to turn
off automatically at a specified
time. (Dimmer : The display window
will be darken by half.)
9
C/V (Skip) : Goes to the
next or previous chapter / track /
file.
c/v (Scan) : Searches
backward or forward.
X REC : USB Direct Recording.
ECHO VOL -/+ (Volume) : Adjusts
echo volume.
VOICE CANCELLER: You can
enjoy the function as karaoke, by
reducing singer vocal of music in
the various source
10 Getting Started
Front panel
i
jk
l m
1
Getting Started
a
e
b
f
c
g
d
h
n
o
p q
rst
u
a1/!(Standby/On)
Turn the power on or off.
lMIC VOL (Microphone Volume)
Adjusts Mic volume.
b CLOCK
Sets a clock and checks a time.
mUSB Port
You can play or record sound files by connecting
the USB device.
cOK / SET
-Acknowledges menu selection.
-Presetting the radio stations.
dALARM
With the ALARM function you can turn Disc, USB
play and Tuner reception on at a desired time.
eUSB REC / DEMO
Records to USB. / Shows Demo mode.
fREGION EQ
Chooses region equalizer.
nMULTI CONTROL / TUNING
-Moves to the another file/ track.
-Tunes in the desired radio station.
-Adjusts clock time or alarm setting.
oMIC 1 / 2 (Microphone) jack
Connect a microphone.
pI (Stop)
Stops playback.
T (Play/Pause)
- Starts or pauses playback.
- Selects Stereo/Mono.
R (Open/Close)
Opens and closes the disc tray.
hBASS BLAST
Press to select BASS effect directly.
USER EQ
Selects the sound effect created by your own.
iECHO VOL (Volume)
Adjusts echo volume.
HOME
Goes to Home menu.
jDisplay window
AUTO DJ
Selects the AUTO DJ mode.
Y / U (Skip)
Goes to the next or previous chapter / track / file.
gVOICE CANCELLER
You can enjoy the function as karaoke, by
reducing singer vocal of music in the various
source
kMASTER VOLUME
Adjusts speaker volume.
Getting Started
11
qDisc tray
rUSER EQ LEVEL
Controls sound register.
sPORT. (Portable) IN jack
Connect a portable device.
1
Getting Started
tF (Function)
Selects the function and input source.
uSOUND EFFECT
Selects a sound effect mode.
Rear panel
a
b
c d
aPower cord
>>Caution
yy Connect the power cord to wall outlet
directly if possible. Or when you use an
extension cable, it is highly recommended
to use an extension cable of 110 V / 15 A
or 230 V / 15 A, otherwise the unit may
not operate properly because of the lack of
power supply.
yy Do not overload the extension cord with
excessive electrical load.
e
bSPEAKERS connector
cANTENNA (FM)
dAUX IN (L/R)
AUX OUT (L/R)
eHDMI OUT TO TV
12 Connecting
Connecting to speakers
Connect the speaker cable plugs to the SPEAKERS
connector. Make sure to connect the speaker’s plug
to the corresponding colored speaker connector
when connecting the plug.
2
>>Caution
yy Do not try to lift the speaker alone. It needs
two persons to lift the speaker. Otherwise
it may result in the speaker malfunction
and cause personal injury and/or property
damage.
yy When you connect the speakers to the unit,
make sure to connect the speaker’s cable and
plug to the corresponding speaker connector.
Connecting
yy Check the volume level before playing music
to prevent infirm, child, and pregnant women
from being shocked by the sudden and loud
sound from the unit.
yy Do not use the unit in a limited space. It may
damage a person’s hearing. It is recommended
to use it in a wide space.
yy Be careful to make sure children not to put
their hands or any objects into the opening
speaker duct hole.
yy Use the speaker supplied with this unit
only. Using any other speaker may cause
malfunction.
yy The speakers contain magnet parts, so color
irregularity may occur on the TV screen or PC
monitor screen. Please use the speakers far
away from either TV screen or PC monitor.
yy Do not press the diaphragm or the dust cap
of the speaker.
Connecting 13
Connections to Your TV
HDMI Out Connection
Unit
TV
,,Tip
yy You can fully enjoy digital audio and video
signals together with this HDMI connection.
yy When you use HDMI connection, you can
change the resolution for the HDMI output.
(Refer to “Resolution Setting” on page 14.)
yy When the HDMI connection with HDCP is
not verified, TV screen is changed to black or
green screen or the snow noise may occur
on the screen. In this case, check the HDMI
connection, or disconnect the HDMI cable.
yy Make sure the unit is connected directly to
the TV. Tune the TV to the correct video input
channel.
2
Connecting
If you have a HDMI TV or monitor, you can connect it
to this unit using a HDMI cable (Type A, High Speed
HDMI™ Cable).
Connect the HDMI OUT jack on the unit to the HDMI
IN jack on a HDMI compatible TV or monitor.
Set the TV’s source to HDMI (refer to TV’s Owner’s
manual).
>>Caution
yy Changing the resolution when the connection
has already been established may result in
malfunctions. To solve the problem, turn off
the unit and then turn it on again.
14 Connecting
,,Note
yy If a connected HDMI device does not accept
the audio output of the unit, the HDMI
device’s audio sound may be distorted or may
not output.
yy When you connect a HDMI or DVI compatible
device make sure of the following:
- Try switching off the HDMI/DVI device and
this unit. Next, switch on the HDMI/DVI
device and leave it for around 30 seconds,
then switch on this unit.
- The connected device’s video input is set
correctly for this unit.
- The connected device is compatible with
720 x 480i (or 576i), 720 x 480p (or
576p), 1280 x 720p, 1920 x 1080i or
1920 x 1080p video input.
2
Connecting
yy Not all HDCP-compatible HDMI or DVI devices
will work with this unit.
- The picture will not be displayed properly
with non-HDCP device.
- This unit does not playback and TV screen
is changed to black or green screen or the
snow noise may occur on the screen.
yy If there is noise or lines on the screen, please
check the HDMI cable and use a higher
version cable than High Speed HDMI™ Cable.
yy If you use LG TV or Bluetooth Function of the
unit, the audio is not output to HDMI.
Resolution Setting
The unit provides several output resolutions for HDMI
OUT.
You can change the resolution using [Setup] menu.
1.Press HOME on the unit or n on the remote
control.
2.Use MULTI CONTROL / TUNING on the unit or
A/D on the remote control to select the [Setup]
and press OK / SET on the unit or b OK on the
remote control. The [Setup] menu appears.
3.Use W/S to select [Display] option then press
D to move to the second level.
4.Use W/S to select the [Resolution] option then
press D to move to the third level.
5.Use W/S to select the desired resolution then
press b OK to confirm your selection.
,,Note
If your TV does not accept the resolution you
have set on the player, you can set resolution to
480p (or 576p) as follows:
Press Z on the remote control or I on the unit
for more than 5 seconds.
Connecting 15
Optional Equipment
Connection
AUX OUT Connection
Connect an input of auxiliary device to the AUX OUT
(L/R) connector.
If your device has only one input for audio(mono),
connect it to the left audio jack on the unit.
AUX IN Connection
Connect an output of auxiliary device (Camcorder, TV,
Player, etc) to the AUX IN (L/R) connector.
2
Connecting
If your device has only one output for audio (mono),
connect it to the left audio jack on the unit.
Audio cable
Red
Auxiliary device
Audio cable
White
DVD, Blu-ray player etc.
16 Connecting
PORT. IN Connection
USB Connection
Connect an output (earphone or line out) of portable
device (MP3 or PMP etc) to the PORT. IN connector.
Connect a USB device (or MP3 player, etc.) to the
USB ports on the unit.
USB device
2
Connecting
Portable cable
,,Note
Removing the USB device from the unit :
1. Choose a different function/mode or
press Z on the remote control or I on
the unit twice in a row.
2. Remove the USB device from the unit.
MP3 player etc.
Listening to music from your portable
player or external device
The unit can be used to play the music from many
types of portable player or external device.
1. Connect the portable player to the PORT. IN
connector on the unit.
Or
Connect the external device to the AUX IN
connector on the unit.
2. Turn the power on by pressing 1/! on the unit
or 1 on the remote control. .
3.Press F to select AUX or PORTABLE Function.
4. Turn on the portable player or external device and
start it playing.
Connecting 17
Antenna Connection
Connect the supplied FM antenna for listening to the
radio.
Connect the FM wire antenna to the FM antenna
connector.
2
,,Note
Be sure to fully extend the FM wire antenna.
Connecting
FM antenna
18 System Setting
Adjust the setup
settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
To display and exit the Setup
menu
1.Press HOME on the unit or n on the remote
control.
Displays the [Home Menu].
You can also set a language for the subtitles and the
Setup menu, among other things. For details on each
Setup menu item, see pages 18 to 21.
OSD Initial language settings Optional
3
System Setting
During the first use of this unit, the initial language
setup menu appears on your TV screen. You must
complete initial language selection before using the
unit. English will be selected as the initial language.
1.Press 1/! on the unit or 1 on the remote
control to turn the unit on. The language setup
menu will appear on the screen.
2.Use WSAD to select a language then press
OK / SET on the unit or b OK on the remote
control.
The confirm menu will appear.
2. Select an [Setup] by using MULTI CONTROL
/ TUNING on the unit or A/D on the remote
control .
3.Press OK / SET on the unit or b OK on the
remote control.
Displays the [Setup].
4.Press n or x BACK on the remote control to
exit in the [Setup] Menu.
Or press HOME on the unit.
About help menu for Setup
Menu
ws
Operation
WS
Moving to another
menu.
a
Move
A
Moving to previous
level.
d
Move
D
Moving to next level
or selecting menu.
x
Close
x BACK
To exit the [Setup]
menu.
b
Select
b OK
To confirm menu.
Move
3.Use AD to select the [Enter] then
press OK / SET on the unit or b OK on the
remote control to finish the language setup.
Buttons
System Setting 19
Language
Resolution
Menu Language
Sets the output resolution of HDMI video signal.
Refer to “Resolution Setting” for details about the
resolution (page 14).
Select a language for the Setup menu and on screen
display.
Disc Audio / Disc Subtitle / Disc Menu
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
[Auto]
If the HDMI OUT jack is connected to
TVs providing display information (EDID),
automatically selects the resolution best suited
to the connected TV.
[Original]
[1080p]
Refers to the original language in which the disc
was recorded.
Outputs 1080 lines of progressive video.
[Other]
Outputs 1080 lines of interlaced video.
3
[720p]
System Setting
To select another language, press numeric
buttons and then OK / SET on the unit or
b OK on the remote control to enter the
corresponding 4-digit number according to the
language code list on the page 43. If you enter
the wrong language code, press CLEAR.
[1080i]
Outputs 720 lines of progressive video.
[480p (or 576p)]
Outputs 480 (or 576) lines of progressive video.
[Off (for Disc Subtitle)]
[480i (or 576i)]
Turns off Subtitle.
Outputs 480 (or (576) lines of interlaced video.
Display
TV Aspect
Select the screen aspect to use based on the shape
of your TV screen.
[4:3]
Select when a standard 4:3 TV is connected.
[16:9]
Select when a 16:9 wide TV is connected.
Display Mode
The Display Mode setting works only when the TV
Aspect mode is set to 4:3.
[Letterbox]
Displays a wide picture with bands on the upper
and lower portions of the screen.
[Panscan]
Automatically displays the wide picture on the
entire screen and cuts off the portions that do
not fit. (If the disc/file is not compatible with Pan
Scan, the picture is displayed at Letterbox ratio.)
20 System Setting
Audio
Lock (Parental Control)
DRC (Dynamic Range Control)
Initial Setting the Area Code:
Make the sound clear when the volume is turned
down (Dolby Digital only). Set to [On] for this effect.
When you use this unit for the first time, you have to
set the Area Code.
Vocal
Select [On] to mix karaoke channels into normal
stereo.
This function is effective for multi-channel karaoke
DVDs only.
HD AV Sync
3
System Setting
Sometimes Digital TV encounters a delay between
picture and sound. If this happens you can
compensate by setting a delay on the sound so that
it effectively ‘waits’ for the picture to arrive: this is
called HD AV Sync. Use WS (on the remote control)
to scroll up and down through the delay amount,
which you can set at anything between 0 and
300ms.
1. Select the [Lock] menu and then press D.
2.Press D.
To access the [Lock] options, you must input the
password you have created. Input a password
and press OK / SET on the unit or b OK on the
remote control. Enter it again and press
OK / SET on the unit or b OK on the remote
control to verify. If you make a mistake before
pressing OK / SET on the unit or b OK on the
remote control, press CLEAR.
3. Select the first character using WS buttons.
4.Press OK / SET on the unit or b OK on the
remote control and select the second character
using WSbuttons.
5.Press OK / SET on the unit or b OK on the
remote control to confirm your Area code
selection.
Rating
Blocks playback of rated DVDs based on their
contents. Not all discs are rated.
1. Select [Rating] on the [Lock] menu then press D.
2. Input a password and press OK / SET on the unit
or b OK on the remote control.
3. Select a rating from 1 to 8 using the WS
buttons.
[Rating 1-8]
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
[Unlock]
If you select unlock, parental control is not active
and the disc plays in full.
4.Press OK / SET on the unit or b OK on the
remote control to confirm your rating selection.
System Setting 21
Password
You can enter or change password.
1. Select [Password] on the [Lock] menu and then
press D.
2.Press OK / SET on the unit or b OK on the
remote control.
3. Input a password and press OK / SET on the unit
or b OK on the remote control.
To change the password, press OK / SET on the
unit or b OK on the remote control when the
[Change] option is highlighted. Input a password
and press OK / SET on the unit or b OK on the
remote control. Enter it again and press OK / SET
on the unit or b OK on the remote control to
verify.
,,Note
If you forget your password, you can clear it
using the following steps:
1. Select the [Setup] menu on the [Home
Menu].
2. Input the 6-digit number “210499” and
press OK / SET on the unit or b OK on the
remote control The password is cleared.
Area Code
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list on
page 42.
1. Select [Area Code] on the [Lock] menu then
press D.
2. Input a password and press OK / SET on the unit
or b OK on the remote control.
3. Select the first character using WS buttons.
4.Press OK / SET on the unit or b OK on the
remote control and select the second character
using WS buttons.
5.Press OK / SET on the unit or b OK on the
remote control to confirm your Area code
selection.
3
System Setting
4.Press HOME on the unit or n on the remote
control to exit the menu.
22 Operating
Using the Home Menu
Basic Operations
1.Press HOME on the unit or n on the remote
control.
Displays the [Home Menu].
1. Insert the disc by pressing B on the remote
control or R on the unit
Or connect the USB device to the USB port.
2.Press HOME on the unit or n on the remote
control..
Displays the [Home Menu].
2. Select an option by using AD.
3.Press OK / SET on the unit or b OK on the
remote control then selected option menu.
3. Select an option by using AD.
If you select the [Movie], [Photo] or [Music]
option when you connect up to two devices, it
appears as belows. Select a media then press
OK / SET on the unit or b OK on the remote
control.
[Music] – Displays [MUSIC] menu.
[Movie] – S
tart video media’s playback or displays the
[MOVIE] menu.
[Photo] – Displays [PHOTO] menu.
4
[Setup] – Displays the [Setup] menu.
Operating
,,Note
You can not select the [Music], [Movie] or
[Photo] option when the USB device is not
connected or a disc is not inserted.
4.Press OK / SET on the unit or b OK on the
remote control then selected option menu.
,,Note
yy For the most Audio CD and DVD-ROM discs,
playback starts automatically.
yy The unit plays only music file contained in the
USB storage device or disc automatically.
Operating 23
To
Do this
Stop
Press Z STOP on the remote
control or I on the unit.
Playback
Press d on the remote control
or T on the unit.
Pause
Press M on the remote control
or T on the unit during
playback.
Frame-byFrame playback
Press M repeatedly to play title
Frame-by-Frame. (DVD Movie
title, Movie file only)
Skipping to the
next/ previous
chapter/ track/
file
Playing
repeatedly or
randomly
Press Y on the unit or
C on the remote control
twice briefly to step back to the
previous chapter/ track/ file.
During playback, press
Y / U on the unit or
C/V on the remote
control repeatedly to select the
required scan speed.
To return to normal speed, press
d on the remote control or T
on the unit.
Press REPEAT repeatedly,
and the current title, chapter
or track will be played back
repeatedly or randomly.
- DVD : Chapter/ Title/ Off
- Video(MOVIE): Title/ All/ Off
- Audio CD/ MP3/ WMA : Track/
All/ Random/ Off
Slowing down
the playing
speed
Do this
In the pause mode, press
Y / U on the unit or
C/V on the remote
control to select the required
speed. (DVD Movie title only)
In the pause mode, press
U on the unit or
V on the remote control
to select the required speed.
(Movie file only)
Press 0 to 9 numerical buttons
Selecting a track/
on the remote control to go to
file directly
the desired file or track directly.
4
Operating
Locating a
point quickly by
playing a file in
fast forward or
fast reverse
During playback, press
Y / U on the unit or
C/V on the remote
control to go to the next
chapter/ track/ file or to return
to the beginning of the current
chapter/ track/ file.
To
24 Operating
Playback Effect
AUTO DJ
Auto DJ blends the end of one song into the
beginning of another for seamless playback. It
equalizes volume across tracks/files for uninterrupted
playback.
Press AUTO DJ on the unit or remote control
repeatedly, the display changes as followings. AUTO
DJ RANDOM -> AUTO DJ SEOUENTIAL -> AUTO DJ
OFF
4
Operating
Mode
Display
Window
Description
OFF
AUTO DJ OFF
-
RANDOM
AUTO DJ
RANDOM
The music is played
randomly on this
mode.
REPEAT
AUTO DJ
SEQUENTIAL
The music is played
repeatedly on this
mode.
,,Note
yy AUTO DJ mode does not support searching
for a section within a track/file or to play
repeatedly or randomly. And AUTO DJ mode
does not support Marked Playback.
yy If you move to other functions or stop the
music by pressing I on the unit twice (or
Z on the remote control twice) on AUTO DJ
mode, AUTO DJ will be disable.
yy AUTO DJ is not supported in the music file
whose length is less than 60 seconds.
yy During recording, AUTO DJ is not available.
yy If you press AUTO DJ during Marked playback,
Marked playback will be disable. And then
AUTO DJ is played.
Operating 25
Using BLUETOOTH®
wireless technology
Listening to music stored on the
Bluetooth devices
About Bluetooth
Before you start the pairing procedure, make sure the
Bluetooth feature is activated on your Bluetooth
device. Refer to your Bluetooth device’s user guide.
Once a pairing operation is performed, it does not
need to be performed again.
Bluetooth is wireless communication technology for
short range connection.
The sound may be interrupted when the connection
interfered by the other electronic wave or you
connect the Bluetooth in the other rooms.
Connecting individual devices under Bluetooth
wireless technology does not incur any charges. A
mobile phone with Bluetooth wireless technology
can be operated via the Cascade if the connection
was made via Bluetooth wireless technology.
Available Devices : Mobile phone, MP3, Laptop, PDA.
(This units be supported the Stereo Headset.)
Bluetooth Profiles
A2DP (Advanced Audio Distribution Profile)
Codec : SBC
1. Select the Bluetooth function by using F until BT
function is selected.
Appears “BT READY” in display window.
2. Operate the Bluetooth device and perform the
pairing operation. When searching for this unit
with the Bluetooth device, a list of the devices
found may appear in the Bluetooth device display
depending on the type of Bluetooth device. Your
unit appears as “LG MINI(XX:XX)”.
,,Note
XX:XX means the last four digits of BT address.
For example, if your unit has a BT address
such as 9C:02:98:4A:F7:08, you will see “LG
MINI(F7:08)” on your Bluetooth device.
3. When this unit is successfully connected with
your Bluetooth device, “PAIRED” appears on the
display window and change to Bluetooth device
name soon. Then “BT” will be appeared on the
display window.
,,Note
Depending on the Bluetooth device type, some
device have a different pairing way.
4. Listening to music.
To play a music stored on your Bluetooth device,
refer to your Bluetooth device’s user guide.
,,Note
yy If you change the function of the unit, the
Bluetooth function is disconnected, operate
pairing again.
(Bluetooth
Function other than the
Bluetooth)
yy Depending on the Bluetooth device type,
some device have a different pairing way.
(Enter the PIN code (0000) as needed.)
4
Operating
In order to use Bluetooth wireless technology,
devices must be able to interpret certain profiles.This
unit is compatible with following profile.
Pairing your unit and Bluetooth device
26 Operating
,,Note
yy The sound may be interrupted when the
connection interfered by the other electronic
wave.
yy You cannot control the Bluetooth device with
this unit.
yy Pairing is limited one Bluetooth device per
one unit and multi-pairing is not supported.
yy Depending on the type of the device, you may
not be able to use the Bluetooth function.
yy You can enjoy wireless system using phone,
MP3, Notebook, headset, etc..
yy When not connected the Bluetooth, “BT
READY” appears on the display window.
yy The Electrical malfunction due to devices
using same frequency such as Medical
equipment, Microwaves or wireless LAN
devices, the connection will be disconnected.
4
Operating
yy When someone stands and interrupts
communication between Bluetooth device
and the player, the connection will be
disconnected.
yy If the gotten away of the distance between
Bluetooth and the unit, the sound quality
is lower and lower the connection will
disconnect when the space between the
Bluetooth and the unit gets out of the
operating range of Bluetooth.
yy If the function is changed to Bluetooth again
from other function, Bluetooth device is
paired automatically.
yy Bluetooth and LG Sound Sync connection are
unavailable during recording.
Operating 27
Radio Operations
Presetting the Radio Stations
Be sure that FM antenna is connected.
(Refer to page 17)
Before tuning, make sure to turn down the volume.
Listening to the radio
1.Press F on the unit or remote control until FM
appears in the display window.
The last received station is tuned in.
2. Auto tuning :
Press and hold TUNING-/+ on the remote control
or Y/U on the unit for about two seconds
until the frequency indication starts to change,
then release. Scanning stops when the unit tunes
in a station.
Or
3. Adjust the volume by rotating volume knob on
the unit or by pressing VOL +/- on the remote
control repeatedly.
Improving poor FM reception
Adjust the antenna to improve the reception when
the radio has poor reception.
1.Press F until FM appears in the display window.
2. Select the desired frequency by pressing
TUNING -/+ on the remote control or rotating
MULTI CONTROL / TUNING on the unit.
3.Press OK / SET on the unit or b OK on the
remote control. A preset number will blink in the
display window.
4.Press PRESET -/+ on the remote control to
select the preset number you want.
5.Press OK / SET on the unit or b OK on the
remote control. on the remote control. The station
is stored.
6. Repeat steps 2 to 5 to store other stations.
7. To listen a preset station, press PRESET -/+ or 0
to 9 numerical buttons on the remote control.
Deleting all the saved stations
1. Press and hold CLEAR on the remote control for
two seconds.
“ERASEALL” will flash up on the unit display.
2.Press CLEAR on the remote control to erase all
the saved radio stations.
Deleting a saved station
1.Press PRESET -/+ to select a preset number you
want to delete.
2.Press CLEAR, the preset number will blink in the
display window.
3.Press CLEAR again to delete the selected preset
number.
4
Operating
Manual tuning :
Press TUNING-/+ on the remote control or
rotate MULTI CONTROL / TUNING on the unit
repeatedly.
You can preset 50 stations for FM
28 Operating
Sound adjustment
Setting the sound mode
This system has a number of pre-set surround sound
fields. The displayed items for the Equalizer may be
different depending on sound sources and effects.
You can select a desired sound mode by using
SOUND EFFECT on the unit or remote control.
On Display
BASS (BASS BLAST)
4
Operating
POP
CLASSIC
ROCK
JAZZ
Description
Reinforces the treble,
bass and surround
sound effect.
This program lends
an enthusiastic
atmosphere to the
sound, giving you the
feeling you are at an
actual rock, pop, jazz or
classic concert.
FOOT BALL
You can enjoy
the sound effect
FOOTBALL STADIUM.
STANDARD
You can enjoy
optimized sound.
You can select a desired sound mode by using
REGION EQ on the remote control.
On Display
Region
FUNK, REGUETON,
SAMBA, BANDA,
MERENGUE, AXE, Latin
SALSA, SERTANEJ, America
CUMBIA, TECNO BR,
FORRO
ARABIC
DANGDUT
Description
Optimized
sound effect
for the
Middle East music genre
prefered in
Indonesia
each region.
AFRO
Africa
INDIA
India
,,Note
yy This function is not operated when the
microphone is connected to the unit.
yy By pressing BASS BLAST on the unit you can
directly select BASS (BASS BLAST) effect.
Setting the USER EQ
You can adjust the sound level of Bass and Treble as
your preference.
1.Press USER EQ on the unit. “USER EQ” is
displayed.
2.Press USER EQ on the unit to select BASS,
MID(MIDDLE) or TRE(TREBLE).
3. Rotate USER EQ LEVEL knob to adjust the
sound level.
4. The setting is automatically saved after 3
seconds.
Operating 29
Advanced Operations
Displaying Disc Information onscreen
You can display various information about the disc
loaded on-screen.
1.Press m INFO/DISPLAY to show various
playback information.
The displayed items differ depending on the disc
type or playing status.
2. You can select an item by pressing WS and
change or select the setting by pressing AD.
Title – C
urrent title number/ total number of titles.
Chapter – C
urrent chapter number/ total number of
chapters.
1.5 times speed playback
r
The 1.5 speed allows you to watch the pictures and
listen to the sound quicker than playing at a normal
speed.
1. During playback, press d to play at 1.5 times
speed. “dX1.5” appears on the screen.
2.Press d again to exit.
Screen Saver
The screen saver appears when you leave the unit in
Stop mode for about five minutes.
Starting play from selected time
ry
To start playing at any chosen time on the file or title.
Audio – Selected audio language or channel.
1.Press m INFO/DISPLAY during playback.
Subtitle – Selected subtitle.
2.Press WS to select the time clock icon and
“--:--:--” appears.
Angle – Selected angle/ total number of angles.
,,Note
If any button is not pressed for a few seconds,
the on-screen display disappears.
To display the DVD Menu
r
When you play a DVD which contains several menu,
you can select the menu you want using the Menu.
1.Press DISC MENU.
The disc’s menu appears.
2. Select the menu by using WSAD.
3.Press d to confirm.
To display the DVD title
r
When you play a DVD which contains several title,
you can select the title you want using the Menu.
1.Press TITLE.
The disc’s title appears.
2. Select the menu by pressing WSAD.
3.Press d to confirm.
3. Input the required start time in hours, minutes,
and seconds from left to right. If you enter the
wrong numbers, press CLEAR to remove the
numbers you entered. Then input the correct
numbers.
For example, to find a scene at 1 hour, 10
minutes, and 20 seconds, enter “11020” by using
numerical buttons.
4.Press b OK to confirm. Playback starts from the
selected time.
Resume playback
ryut
The unit records the point where you pressed the
Z depending on the disc.
If “MZ (Resume Stop)” appears on the screen briefly,
press d to resume playback (from the scene point).
If you press Z twice or unload the disc,
“Z”(Complete Stop) appears on the screen. The unit
will clear the stopped point.
,,Note
yy The resume point may be cleared when a
button is pressed (for example; 1, B, etc).
yy This function may not work on some disc or
title/track.
4
Operating
Time – Elapsed playing time.
30 Operating
Changing subtitle code page
y - Optional
If the subtitle is not displayed properly, you can
change the subtitle code page to view the subtitle file
properly.
1. During playback, press m INFO/DISPLAY to
display the On-Screen display.
2.Use WS to select the [Code Page] option.
[Mark Play]
Marked playback.
[Current Play]
Normal playback.
,,Note
If you want to select all files on the list, select
[Select All] and press b OK.
3.Use AD to select desired code option.
4
4.Press x BACK to exit the On-Screen display.
To delete a Marker
Marked Playback
1.Use WS to select the track that you wish to
erase from the marked file.
ut
2.Press MARKER.
The mark function enables you to store your
favourite files from any disc or USB device in the unit
memory.
To delete all Markers
1. Select [Music] on the [Home Menu].
Operating
Returning to the upper folder.
(MP3/ WMA only)
File information will be displayed
according to the ID3TAG information
on the appropriate music file. (MP3
only)
Selecting all tracks/ files.
Deselecting all tracks/files.
Moving to the previous or next
file list.
2. Select a desired music on the [List] by using the
WS then press MARKER to appears the mark
on the list.
3.Press b OK or d.
Displays the play mode.
4. Select the play mode by using the WS and press
b OK.
Use WSAD to select [Deselect All] then press
b OK in program edit mode.
,,Note
The markers are also cleared when the disc or
USB device is removed, the unit is switched to
power off or the function is switched to others.
Operating 31
Viewing a PHOTO file
About help menu in the full screen
Menu
Buttons
Operation
Menu
m
INFO/
DISPLAY
Displaying the Option
menu.
a/d
Prev./ Next
A/D
i
This unit can play discs with photo files.
1. Select [Photo] on the [Home Menu] and press
b OK.
Moving to the previous or next
file list.
x
List
x BACK
Moving to another
file.
Returning to the
[Photo] menu.
Options while viewing a photo
You can use various options during viewing a photo in
full screen.
1. While viewing a photo in full screen, press
m INFO/DISPLAY to display the option menu.
2. Select an option using WSAD.
Returning to the upper
folder.
4
3. If you want to view a slide show, press WS to
highlight a file and press d.
About help menu in the [Photo] menu
Operating
2.Press WS to select a folder, and then press
b OK.
a
Menu
Buttons
Operation
d Slide
Show
d
Viewing a slide show.
a Current photo/ Total number of photos –
Use AD to view previous/next photo.
wsad
Move
WSAD
Moving to another
file or content.
b Slide Show d/M – Press b OK to start or
pause slide show.
b
Select
b OK
Viewing a particular
file.
c Speed x3/ x2/ x1 – Use b OK to select a
delaying speed between photos in a slide
show.
x
Close
x BACK
Returning to the
[Home Menu].
d Rotate – Press b OK to rotate the photo.
b
c
d
e
e Go to list – Press b OK to return [Photo] list.
32 Operating
Recording to USB
You can record music or sound souce to USB device
by connecting in to the port on the unit.
1. Connect the USB device to the unit.
2. Select a mode in which you want to record.
Playback a sound source first.
3. Start the recording by pressing X REC.
4. To stop recording, press Z.
[All tracks/ files recording]
Record to USB in stop or play mode.
[Program list recording]
After marking desired file(s) and you can record
it to USB (Refer to the page 30).
It’ll be stored as follows.
4
Audio CD
Operating
MP3/ WMA
,,Note
yy You can check the recording percentage rate
for the USB record on the screen during the
recording. (Audio CD or MP3/ WMA CD only)
yy During recording MP3/WMA, there is no
sound.
yy When you stop recording during playback, the
file that has been recorded at that time will
be stored. (Except MP3/WMA files)
yy Do not remove the USB device or turn off
the unit during USB recording. If does not, an
incomplete file may be made and not deleted
on PC.
yy Recording through microphones is not
available
yy If USB recording does not work, the message
like “NO USB”, “ERROR”, “USB FULL” or “NO
REC” is displayed on the display window.
yy Multi card reader device or external HDD can
not be used for USB recording.
yy A file is recorded by 128 Mbyte (about 2
hours) when you record for a long term. There
are recorded less than 4 files.
The other
sources (Tuner,
AUX, Portable)
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights.
yy In the state CD-G, DTS disc USB record is not
operated.
yy The files in the sub-folders are not recorded
during all track recording.
yy You may not record more than 999 files.
yy The numbering of the recording file is entered
from the lowest number. So if you delete
some of the recording files, the next recording
file could be the lowest number among them.
yy You can not record in AUTO DJ mode.
yy VOICE CANCELLER will be reset, if you use
recording function during operating VOICE
CANCELLER.
yy VOICE CANCELLER can not be operated
during recording.
Operating 33
Other Operations
Sleep Timer Setting
Press SLEEP one or more times to select delay time
between 10 and 180 minutes, after the unit will turn
off.
To check the remaining time, press SLEEP.
To cancel the sleep function, press SLEEP repeatedly
until “SLEEP 10” appears, and then press SLEEP
once again while “SLEEP 10” is displayed.
,,Note
yy You can check the remaining time before the
Unit turns off.
yy Press SLEEP The remaining time appears in
the display window.
Press SLEEP once. The display window will be darken
by half. To cancel it, press SLEEP repeatedly until dim
off.
,,Note
All the LED turns off when Dimmer is being
operated.
Last Scene Memory
r
This unit memorizes last scene from the last disc that
is viewed. The last scene remains in memory even if
you remove the disc from the unit or switch off the
unit. If you load a disc that has the scene memorized,
the scene is automatically recalled.
Power Resume - Optional
r
Even if the power suddenly goes out, turn on the
unit and then it plays a position where the contents
is being played. System will periodically save current
playback status.
You must select the appropriate system mode for
your TV system. Press and hold M for more than five
seconds to be able to select a system in the [Home
Menu]. (NTSC
PAL)
,,Note
If the USB device is connected or a disc is
inserted, this function is not operated.
Turn off the sound temporarily
Press
on the remote control to mute your sound.
You can mute your unit, for example, to answer the
telephone, the “MUTE” will appear in the display
window.
To cancel it, press
level.
again or change the volume
4
Operating
Dimmer
System Select - Optional
34 Operating
CHILDSAFE Mode
VOICE CANCELLER
This function helps to prevent you from being
surprised when you turn on the unit in case that the
volume of the unit is set at a high level.
You can enjoy the function as karaoke,, by reducing
singer vocal of music in the various source.
(MP3/ WMA/ CD/ etc.)
To turn on CHILDSAFE mode, press and hold
OK / SET on the unit when the volume of the unit is
“MIN”.
Press the VOICE CANCELLER, and “ON” will appear
in display window.
In CHILDSAFE mode, the volume increase gradually.
The quality of the VOICE CANCELLER may be
different depending on the recording conditions of
music files.
To turn off CHILDSAFE mode, press and hold
OK / SET on the unit when the volume of the unit is
“MIN”.
,,Note
In case of DVD/CD, USB, BT function or LG TV
Function, CHILDSAFE mode does not work after
about 2 minutes from power on the unit even if
this mode is enabled.
4
DEMO
Operating
In the power off state, it demonstrates the function
on display window and a display by pressing
USB REC / DEMO.
To cancel the USB REC / DEMO., press it again.
,,Note
yy While in DEMO, this unit will keep DEMO
status even if you unplug the power cord
connection.
yy You can enjoy other functions during the
DEMO, the DEMO will temporarily pause.
- Without input key in 10 sec, the DEMO will
play back automatically.
To cancel it, press VOICE CANCELLER again.
,,Note
yy This function is available to use only when a
microphone is connected.
yy It is not available on the MONO source.
Operating 35
Using Microphone
1. Connect your microphone to the MIC jack.
Setting the Clock
2. Play the music you want.
1. Turn the unit on.
3. Sing along with the accompaniment. Adjust
the microphone volume by rotating MIC VOL
clockwise or counterclockwise on the unit or by
pressing MIC VOL -/+ on the remote control
repeatedly.
2. Press and hold CLOCK.
,,Note
yy When not using the microphone, set the
MIC VOL to minimum or turn off the MIC and
remove the microphone from the MIC jack.
yy If the microphone is set too near the speaker,
a howling sound may be produced. In this
case, move the microphone away from the
speaker or decrease the sound level by using
the MIC VOL on the unit or press MIC VOL on the remote control. .
yy If your microphone’s sound feels not loud
though MIC VOL is max, you can adjust only
audio source volume lower.
- Follow below step.
1. Press and hold VOICE CANCELLER on
the unit.
2. Reduce Audio Source Volume by rotating
MASTER VOLUME counter-clockwise
on the unit. To initialize it, power off or
remove the microphone from the MIC
jack.
yy You can give an echo effect to the sound
from the microphones by using the
ECHO VOL.
- AM 12:00 (for an AM and PM display) or 0:00
(for a 24 hour display)
4.Press OK / SET to confirm your selection.
5. Select the hours by rotating
MULTI CONTROL / TUNING on the unit.
6.Press OK / SET.
7. Select the minutes by rotating
MULTI CONTROL / TUNING on the unit.
8.Press OK / SET.
4
Operating
yy If sound through the microphone is extremely
loud, it may be distorted. In this case, rotate
MIC VOL on the unit or press MIC VOL - on
the remote control. to minimum.
3. Select time mode by rotating
MULTI CONTROL / TUNING on the unit.
36 Operating
Using your player as an alarm
clock
Auto power down
1. Turn the unit on.
This unit will turn itself off to save electricity in the
case were the main unit is not connected to an
external device and is not used for 20 minutes.
The unit will also turn itself off after six hours if the
Main unit has been connected to another device
using the analog inputs.
2. Press and hold ALARM.
3. Rotate MULTI CONTROL / TUNING on the unit
to change the hours and minutes and press
OK / SET to save.
4. Rotate MULTI CONTROL / TUNING on the unit
to select function and press SET to save.
- Press C/V on the remote control to
select a memory No. when you select Tuner and
then, press OK / SET.
If there is no memory No., this step is skipped.
5. Rotate MULTI CONTROL / TUNING on the unit
to change the volume and press OK / SET to
save.
,,Note
4
Operating
yy If you set the clock time, you can check the
time by pressing CLOCK even when the
player is turned off.
yy You can set alarm after you set the clock
time.
yy If you set the clock time and alarm, you
can check the alarm setting informaiton
by pressing ALARM even when the unit is
turned off.
yy You can select ALARM ON/OFF mode by
pressing ALARM.
yy In case of DVD/CD or USB, this function is
available when you have music file. If you do
not have music file, the function is changed
to Tuner.
How to disconnect the wireless
network connection or the wireless
device.
Turn off the unit by pressing the power button for
more than 5 seconds.
Operating 37
AUTO POWER On
Auto function change
This unit automatically turns on by an input source :
LG TV or Bluetooth
This unit recognizes input signals such as Bluetooth
and LG TV and then changes suitable function
automatically.
If you try to connect your Bluetooth device, this unit
turns on and connects your Bluetooth device. You
can play your music.
,,Note
yy Depending on the connected device, this
function may not operate.
yy Depending on the connected device, the unit
turns on but Bluetooth function may not be
connected.
yy If you disconnect Bluetooth connection by
this unit, some Bluetooth devices try to
connect to the unit continually. Therefore it is
recommended to disconnect the connection
before turning off the unit.
yy If you have already paired with this unit,
automatically this unit can turn on by an input
source when this unit is turned off.
yy If you turn off the unit by pressing the power
button for more than 5 seconds, Auto Power
On function is disabled. To activate it, turn on
the unit.
When you try to connect your Bluetooth device to
this unit, Bluetooth function is selected. Play your
music on the Bluetooth device.
When LG TV signal comes in
When you turn on your LG TV connected by LG
Sound Sync, this unit changes the function to LG TV.
You can hear the sound from your TV.
,,Note
yy This unit does not respond to the bluetooth
connection signal while using the LG TV
function.
yy If you using the bluetooth function, this unit
does not respond to LG TV connection signal.
yy The bluetooth unit or the LG TV which is not
paired with this unit, cannot use the auto
function change.
yy If you change the this unit’s function to other
function, some bluetooth unit may try to
connecting in succession. Disconnect the
bluetooth connection before changing of the
this unit’s function.
4
Operating
yy If you turn on the unit using LG TV or
Bluetooth function, proper function of this
unit is turned on.
When you try to connect Bluetooth
device
38 Operating
LG Sound Sync
You can control some functions of this unit by
your TV’s remote control with LG Sound Sync. It is
compatible with LG TV that supports LG Sound Sync.
Make sure your TV has the LG Sound Sync logo.
Controllable function by LG TV’s remote control :
Volume up/down, mute
Refer to the TV’s instruction manual for the details of
LG Sound Sync.
1. Turn on the unit by pressing 1/! on the unit or
1 on the remote control.
2.Press F on the unit or remote control until LG TV
function is selected.
4
Operating
3. Set up the sound output of TV to listen to the
sound through this unit :
TV setting menu [Sound] -> [TV Sound output]
-> [LG Sound Sync (Wireless)]
“PAIRED” appears on the display window for
about 3 seconds and then you can see “LG TV”
on the display window if the TV and this unit are
connected normally.
,,Note
yy You can also use the remote control of this
unit while using LG Sound Sync. If you use TV’s
remote control again, the unit synchronizes
with the TV.
yy If the connection fails, check the conditions of
this unit and your TV : power, function.
yy Make sure of the condition of this unit and
the connection in the cases below when using
LG Sound Sync.
-- Turn off the unit.
-- Changing to a different function.
-- Disconnecting the wireless connection
caused by interference or a distance.
yy The amount of time to turn off this unit is
different depending on your TV.
yy Details of TV setting menu vary depending on
the manufacturers or models of your TV.
yy If you turned off the unit directly by pressing
1/! on the unit or 1 on the remote control,
LG Sound Sync will be disconnected. To use
this function again, you should reconnect the
TV and the unit.
yy The volume may be increased when the TV
and this unit is connected by LG Sound Sync.
Decrease the TV volume and then connect
with this unit.
yy Bluetooth connection is unavailable after
connecting LG TV.
yy Bluetooth and LG Sound Sync connection are
unavailable during recording.
Troubleshooting 39
Troubleshooting
Problem
Cause & Solution
yy Turn off the power of this unit and the connected external device (TV, Woofer,
DVD-player, Amplifier, etc.) and turn it on again.
The unit does not work
properly.
yy Disconnect the power cord of this unit and the connected external device (TV,
Woofer, DVD-player, Amplifier, etc.) and then try connecting again.
yy Previous setting may not be saved when device power is shut off.
No Power.
No picture
No sound.
yy The power cord is not plugged in. Plug in the power cord.
yy Check whether electricity failed.
Check the condition by operating other electronic devices.
yy Select the appropriate video input mode on the TV so the picture from the unit
appears on the TV screen.
yy Connect the video cables securely to both the TV and unit.
yy Check whether you select right function.
Press function button and check the selected function.
yy Check to see if the Speakers are connected correctly. Speaker cables connected
correctly.
The DVD picture quality is yy Clean the disc using a soft cloth with outward strokes.
poor
Humming noise heard
while a DVD or CD is
playing
The unit does not start
playback.
yy Place the disc with the label or printed side facing upwards.
yy Enter your password or change the rating level.
yy Clean the disc using a soft cloth with outward strokes.
yy Move unit further away from your TV.
yy An unplayable disc is inserted. Check the playable disc.
yy No disc is inserted. Insert a disc.
yy The disc is dirty. Clean the disc. (Refer to page 45)
yy The disc is inserted upside down.
Place the disc with the label or printed side facing upwards.
Troubleshooting
A DVD/CD will not play
yy Insert a disc.
yy Insert a playable disc (check the disc type, colour system and regional code).
5
40 Appendix
Problem
Cause & Solution
yy The antenna is positioned or connected poorly.
Connect the antenna securely.
Radio stations cannot be
tuned in properly.
yy The signal strength of the radio station is too weak.
Tune to the station manually.
yy No stations have been preset or preset stations have been cleared (when tuning
by scanning preset channels).
Preset some radio stations, see page 27 for details.
yy The remote control is too far from the unit.
Operate the remote control within about 23 ft (7 m).
The remote control does yy There is an obstacle in the path of the remote control and the unit.
Remove the obstacle.
not work properly.
yy The batteries in the remote control are exhausted.
Replace the batteries with new ones.
LG Sound Sync does not
work.
The AUTO POWER
function does not work.
6
yy Check whether your LG TV supports LG Sound Sync.
yy Check connection of LG Sound Sync.
yy Check sound setting of your TV and this unit.
yy Check connection of the external device such as TV or Bluetooth device.
yy Depending on the connected device, this function may not operate.
Appendix
Appendix 41
Controlling a TV with
the Supplied Remote
Control
You can control your TV using the buttons below.
By pressing
You can
1 (TV POWER)
Turn the TV on or off.
INPUT
Switch the TV’s input source
between the TV and other
input sources.
PR/CH W/S
Scan up or down through
memorized channels.
VOL +/–
Adjust the volume of the TV
(TV Mute)
Depending on the unit being connected, you
may not be able to control your TV using some
of the buttons.
You can operate your TV with the supplied remote
control.
If your TV is listed in the table below, set the
appropriate manufacturer code.
1. While holding down 1 (TV POWER) button, and
press the manufacturer code for your TV with the
numerical buttons (see the table below).
Manufacturer
Code Number
LG
1(Default), 2
Zenith
3, 4
GoldStar
1, 2
Samsung
6, 7
Sony
8, 9
Hitachi
4
2. Release the 1 (TV POWER) button to complete
setting.
Depending on your TV, some or all buttons may not
function on the TV, even after entering the correct
manufacturer code. When you replace the batteries
of the remote, the code number you have set may be
reset to the default setting. Set the appropriate code
number again.
6
Appendix
,,Note
Mutes the sound.
Setting up the remote to control
your TV
42 Appendix
Area Code List
Choose an area code from this list.
Area
Afghanistan 6
Code Area
AF
Code Area
Code Area
Code
Appendix
Fiji FJ
Monaco MC Singapore SG
ArgentinaAR
Finland FI
Mongolia MN Slovak Republic SK
Australia
AU
France FR
Morocco MA Slovenia SI
Austria AT
Germany DE
Nepal NP
South Africa ZA
Belgium BE
Great Britain GB
Netherlands NL
South Korea KR
Bhutan BT
Greece GR
Antilles AN
Spain ES
Bolivia BO
Greenland GL
New Zealand NZ
Sri Lanka LK
Brazil BR
Hong Kong HK
Nigeria NG
Sweden SE
Cambodia KH
Hungary HU
Norway NO
Switzerland CH
Canada CA
India IN
Oman OM Taiwan TW
Chile CL
Indonesia ID
Pakistan PK
Thailand TH
China CN
Israel IL
Panama PA
Turkey TR
Colombia CO
Italy IT
Paraguay PY
Uganda UG
Congo CG
Jamaica JM
Philippines PH
Ukraine UA
Costa Rica CR
Japan JP
Poland PL
United States US
Croatia HR
Kenya KE
Portugal PT
Uruguay UY
Czech Republic CZ
Kuwait KW Romania RO
Uzbekistan UZ
Denmark DK
Libya LY
Vietnam VN
Ecuador EC
Luxembourg Zimbabwe ZW
Egypt EG
El Salvador Ethiopia LU
Russian
Federation RU
Malaysia MY
Saudi Arabia SA
SV
Maldives MV Senegal ET
Mexico MX
SN
Appendix 43
Language code List
Use this list to input your desired language for the following initial settings: [Disc Audio],
[Disc Subtitle] and [Disc Menu].
LanguageCode LanguageCode LanguageCode LanguageCode
6565 French 7082 Lithuanian 7684 Sindhi 8368
Afrikaans 6570 Frisian 7089 Macedonian 7775 Singhalese 8373
Albanian 8381 Galician 7176 Malagasy 7771 Slovak 8375
Ameharic 6577 Georgian 7565 Malay 7783 Slovenian 8376
Arabic 6582 German 6869 Malayalam 7776 Spanish 6983
Armenian 7289 Greek 6976 Maori 7773 Sudanese 8385
Assamese 6583 Greenlandic 7576 Marathi 7782 Swahili 8387
Aymara 6588 Guarani 7178 Moldavian 7779 Swedish 8386
Azerbaijani 6590 Gujarati 7185 Mongolian 7778 Tagalog 8476
Bashkir 6665 Hausa 7265 Nauru
7865 Tajik 8471
Basque 6985 Hebrew 7387 Nepali 7869 Tamil 8465
Bengali; Bangla 6678 Hindi 7273 Norwegian 7879 Telugu 8469
Bhutani 6890 Hungarian 7285 Oriya 7982 Thai 8472
Bihari 6672 Icelandic 7383 Panjabi 8065 Tonga 8479
Breton 6682 Indonesian 7378 Pashto, Pushto 8083 Turkish 8482
Bulgarian 6671 Interlingua 7365 Persian 7065 Turkmen 8475
Burmese 7789 Irish 7165 Polish 8076 Twi 8487
Byelorussian 6669 Italian 7384 Portuguese 8084 Ukrainian 8575
Chinese 9072 Japanese 7465 Quechua 8185 Urdu 8582
Croatian 7282 Kannada 7578 Rhaeto-Romance 8277 Uzbek 8590
Czech 6783 Kashmiri 7583 Rumanian 8279 Vietnamese 8673
Danish 6865 Kazakh 7575 Russian 8285 Volapük 8679
Dutch 7876 Kirghiz 7589 Samoan 8377 Welsh 6789
English 6978 Korean 7579 Sanskrit 8365 Wolof 8779
Esperanto 6979 Kurdish 7585 Scots Gaelic 7168 Xhosa 8872
Estonian 6984 Laothian 7679 Serbian 8382 Yiddish 7473
Faroese 7079 Latin 7665 Serbo-Croatian 8372 Yoruba 8979
Fiji 7074 Latvian, Lettish 7686 Shona 8378 Zulu 9085
Finnish 7073 Lingala 7678
6
Appendix
Afar 44 Appendix
Trademarks and
Licenses
All other trademarks are trademarks of their
respective owners.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
6
Appendix
The Bluetooth® word mark and logos are owned
by the Bluetooth® SIG, Inc. and any use of such
marks by LG Electronics is under license.
Other trademarks and trade names are those of
their respective owners.
Notes on Copyrights
yy This product incorporates copyright protection
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Rovi, and is intended for home and
other limited viewing uses only unless otherwise
authorized by Rovi. Reverse engineering or
disassembly is prohibited.
yy Under the U.S. Copyright laws and Copyright
laws of other countries, unauthorized recording,
use, display, distribution, or revision of television
programs, videotapes, BD-ROM discs, DVDs, CDs
and other materials may subject you to civil and/or
criminal liability.
Appendix 45
Maintenance
Handling the Unit
When shipping the unit
Notes on Discs
Handling Discs
Do not touch the playback side of the disc. Hold the
disc by the edges so that fingerprints do not get on
the surface. Never stick paper or tape on the disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center to out.
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for old vinyl records.
Please save the original shipping carton and packing
materials. If you need to ship the unit, for maximum
protection, re-pack the unit as it was originally
packed at the factory.
Keeping the exterior surfaces clean
Do not use volatile liquids such as insecticide spray
near the unit. Wiping with strong pressure may
damage the surface. Do not leave rubber or plastic
products in contact with the unit for a long period of
time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not use
strong solvents such as alcohol, benzine, or thinner,
as these might damage the surface of the unit.
Maintaining the Unit
The unit is a high-tech, precision device. If the optical
pick-up lens and disc drive parts are dirty or worn, the
picture quality could be diminished. For details, please
contact your nearest authorized service center.
6
Appendix
46 Appendix
General specifications
General
Power requirements
Refer to the main label on the unit.
Refer to the main label on the unit.
Power consumption
Networked standby : 0.5 W
(If all network ports are activated.)
Dimensions (W x H x D)
450 mm x 160 mm x 355 mm
Net Weight (Approx.)
5.6 kg
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity
65 %
Inputs / Outputs
HDMI OUT (video/audio)
19 pin (Type A, HDMI™ Connector )
Analog audio out (AUX OUT)
2,0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R)
Analog audio in (AUX IN)
2,0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R)
Portable in (PORT. IN)
1.2 Vrms (3.5 mm stereo jack) x 1
Microphone (MIC 1/2)
Sensitivity 20 mV (1 kHz), 6.3 mm jack x 2
Tuner
FM Tuning Range
87,5 to 108.0 MHz or 87,50 to 108,00 MHz
System
6
Appendix
Frequency Response
40 to 20,000 Hz
Signal-to-noise ratio
More than 75 dB
Dynamic range
More than 80 dB
Bus Power Supply (USB)
5 V 0 500 mA
Amplifier (RMS Output power)
Total output
1,100 W
FRONT
550 W X 2 (6 Ω at 1 khz, 25 % THD)
yy Design and specifications are subject to change without notice.
Appendix 47
Speakers specifications
Front speaker
Type
3 Way 3 Speaker
Impedance
6Ω
Rated Input power
550W
Max. Input power
1110W
Net Dimensions (W x H x D)
321 mm x 454 mm x 301 mm
Net Weight
9,6 kg
yy Design and specifications are subject to change without notice.
yy
6
Appendix
Download PDF