LG | FX166 | LG FX166 Owner’s Manual

SIMPLE MANUAL
3D Blu-ray™
Micro Hi-Fi System
Please read this manual carefully before operating
your set and retain it for future reference.
FX166 (FX166, FXS166V)
P/NO: MFL67204931
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 1
2011-04-28 �� 10:19:13
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 2
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service centre.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
centre. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
2011-04-28 �� 10:19:14
Getting Started
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
Notes on Copyrights
This product incorporates copyright protection
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Rovi, and is intended for home and
other limited viewing uses only unless otherwise
authorized by Rovi. Reverse engineering or
disassembly is prohibited.
Important Notice for TV colour
system
1
Getting Started
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
3
The colour system of this player differs according to
currently playing discs.
For example, when the player plays the disc
recorded in the NTSC colour system, the image is
output as an NTSC signal.
Only the multi system colour TV can receive all
signals output from the player.
yy If you have a PAL colour system TV, you will see
just distorted images when using discs or video
contents recorded in NTSC.
yy The multi system colour TV changes the colour
system automatically according to input signals.
In case that the colour system is not changed
automatically, turn it off and then on to see
normal images on screen.
yy Even if the disc recorded in NTSC colour system
are well displayed on your TV, these may not be
recorded correctly on your recorder.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 3
2011-04-28 �� 10:19:14
4
Getting Started
Supplied Accesorries
Network Software
Update
1
Getting Started
Network update notification
Video cable (1)
FM antenna (1)
Remote control (1)
Batteries(2)
From time to time, performance improvements
and/or additional features or services may be
made available to units that are connected to a
broadband home network. If there is new software
available and the unit is connected to a broadband
home network, the player will inform you about the
update as follows.
Option 1:
1. The update menu will appear on the screen
when you turn on the player.
Owner’s Manual & PC
Software CD
HDMI cable (1)
2. Use A/D to select a desired option and then
press ENTER (b).
[OK]
Starts the software update.
[Cancel]
Exits the update menu and
displays it next booting.
[Hide]
Exits the update menu and
it does not appear until next
software is uploaded in the
update server.
Option 2:
If the software update is available from the update
server, the “Software Update” icon appears in the
Home menu. Press blue (B) coloured button to start
the update procedure.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 4
2011-04-28 �� 10:19:15
Table of Contents
Table of Contents
1
Getting Started
2
4
4
4
6
6
Safety Information
– Supplied Accesorries
Network Software Update
– Network update notification
Introduction
– Playable Discs and symbols used in
this manual
– File requirement
Front panel
Rear panel
Remote control
7
8
10
12
2 Connecting
13
4 Operating
16
16
16
16
17
17
General Playback
– Using [HOME] menu
– Playing a Disc
– Playing a file on disc/USB device
– Basic operations for video and audio
content
On-Screen display
1
2
5 Troubleshooting
18
19
19
Troubleshooting
– Customer Support
– Open source software notice
3
6 Appendix
20 Trademarks and Licenses
22 Specifications
4
Attaching the speakers to the unit
3 System Setting
14
14
14
15
5
5
Settings
– Adjust the Setup Settings
– Resolution Setting
– Wired Network Setup
6
To view the Owner's Manual on the CD-ROM
Load the supplied CD-ROM into the CD-ROM drive on your PC. After a while, the web page will open
automatically. (Windows users only)
If the web page does not appear automatically, browse the CD-ROM drive and double-click the "index.
html" file.
To view the Owner's Manual on the CD-ROM, Adobe Acrobat Reader must be installed on your PC. The
"Acrobat Reader" folder on the CD-ROM contains the installation program for Acrobat Reader.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 5
2011-04-28 �� 10:19:15
6
Getting Started
Introduction
1
Playable Discs and symbols used in this manual
Getting Started
Media/Term
Logo
Symbol
e
Description
yy Discs such as movies that can be purchased or
rented.
yy “Blu-ray 3D” discs and “Blu-ray 3D ONLY” discs.
yy BD-R/RE discs that are recorded in BDAV format.
Blu-ray
y
u
i
r
DVD-ROM
yy BD-R/RE discs that contain Movie, Music or
Photo files.
yy ISO 9660+JOLIET, UDF and UDF Bridge format
yy Discs such as movies that can be purchased or
rented.
yy Movie mode and finalized only
yy Supports the dual layer disc also
DVD-R
DVD-RW
DVD+R
DVD+RW
(8 cm, 12 cm)
DVD-RW (VR)
(8 cm, 12 cm)
Audio CD
(8 cm, 12 cm)
CD-R/RW
(8 cm, 12 cm)
Note
–
Caution
–
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 6
o
Finalized AVCHD format
y
u
i
yy DVD±R/RW discs that contain Movie, Music or
Photo files.
yy ISO 9660+JOLIET, UDF and UDF Bridge format
r
VR mode and finalized only
t
Audio CD
y
u
i
yy CD-R/RW discs that contain Movie, Music or
Photo files.
,
>
Indicates special notes and operating features.
yy ISO 9660+JOLIET, UDF and UDF Bridge format
Indicates cautions for preventing possible
damages from abuse.
2011-04-28 �� 10:19:16
Getting Started
7
File requirement
Movie files
Disc,
USB
DLNA
1
File
Extension
Codec Format
Audio Format
Subtitle
.avi, .mpg,
.mpeg, .mkv,
.mp4, .asf,
.wmv, .m4v
(DRM free)
DIVX3.xx, DIVX4.xx, DIVX5.xx, DIVX6.xx
(standard playback
only), XVID, MPEG1 SS,
H.264/MPEG-4 AVC,
MPEG2 PS, MPEG2 TS,
Dolby Digital,
DTS, MP3,
WMA, AAC,
AC3
SubRip (.srt / .txt), SAMI (.smi),
SubStation Alpha (.ssa/.txt),
MicroDVD (.sub/.txt), VobSub
(.sub), SubViewer 1.0 (.sub),
SubViewer 2.0 (.sub/.txt), TMPlayer
(.txt), DVD Subtitle System (.txt)
.avi, .divx,
.mpg, .mpeg,
.mkv, .mp4,
DIVX3.xx, DIVX4.xx, DIVX5.xx, DIVX6.xx
(standard playback
only), XVID, MPEG1 SS,
H.264/MPEG-4 AVC,
MPEG2 PS, MPEG2 TS,
Dolby Digital,
DTS, MP3,
WMA, AAC,
AC3
SubRip (.srt / .txt), SAMI (.smi),
SubStation Alpha (.ssa/.txt),
MicroDVD (.sub/.txt), SubViewer
1.0 (.sub), SubViewer 2.0 (.sub/.
txt), TMPlayer (.txt), DVD Subtitle
System (.txt)
Getting Started
File
Location
Music files
File
Location
Disc,
USB,
DLNA
File
Extension
mp3, .wma,
.wav, .m4a
(DRM free)
Sampling Frequency
within 32 - 48 kHz
(WMA), within 16 - 48
kHz (MP3)
Bitrate
within 32 - 192
kbps (WMA), within
32 - 320 kbps (MP3)
Note
Some wav files are
not supported on this
player.
Photo files
File
Location
Disc,
USB,
DLNA
File
Extension
.jpg, .jpeg,
.png
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 7
Recommanded
Size
Note
Less than 4,000 x 3,000 x 24 bit/pixel Progressive and lossless
Less than 3,000 x 3,000 x 32 bit/pixel compression photo image files
are not supported.
2011-04-28 �� 10:19:16
8
Getting Started
Front panel
1
Getting Started
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 8
2011-04-28 �� 10:19:16
Getting Started
a Disc slot
b iPod dock
c 1/! (POWER)
Switches the unit ON or OFF.
e FUNC. (FUNCTION)
Changes the input source or function.
h B (OPEN/CLOSE)
Insert or release a disc.
i C/V (Skip/Search):
Goes to next or previous file/track/chapter.
Searches backward or forward (Press and hold)
Tunes in the desired radio station.
f USB Port
d/M (PLAY / PAUSE)
Starts playback.
Pauses playback temporarily, press again to exit
pause mode.
g EQ
You can choose fixed sound impression.
j -/+ (VOLUME)
Adjusts speaker volume.
SET, DEMO
Confirms the setting.
Press DEMO in power off state to demonstrate
the function on display window. To cancel it,
press DEMO again.
TIMER
With the TIMER function, you can have the
radio reception, CD play and USB play turned
on and off at the desired time.
CLOCK
For setting the clock and checking the time.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 9
1
Getting Started
d Display window
Shows the current status of the unit.
9
Z (STOP)
Stops playback.
k USB REC.
Recoding to USB.
l PORT. IN
Connects to a portable player with audio
outputs.
PHONES
Headphone jack
2011-04-28 �� 10:19:16
10
Getting Started
Rear panel
1
Getting Started
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 10
2011-04-28 �� 10:19:16
Getting Started
a OPTICAL IN
Connects to optical audio equipment.
b HDMI OUT
Connects to TV with HDMI inputs.
(Interface for digital audio and video)
dAntenna Connector
FM- Connects the FM wired antenna.
eVIDEO OUT
Connects to a TV with video inputs.
fCOMPONENT VIDEO (Y PB PR)OUTPUT
(PROGRESSIVE SCAN)
Connects to a TV with Y PB PR inputs.
h Cooling Fan
iPower cord
1
Getting Started
c LAN PORT
11
gSpeakers connectors
Connects the speaker cables.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 11
2011-04-28 �� 10:19:16
12
Getting Started
Remote control
• • • • • • a • • • • • • 1
Getting Started
1 (POWER): Switches the player
ON or OFF.
B (OPEN/CLOSE): Insert or
release a disc.
RADIO&INPUT (P): Changes
input mode.
0-9 numerical buttons: Selects
numbered options in a menu or
inputs letters in the keypad menu.
CLEAR: Removes a mark on the
search menu or a number when
setting the password.
REPEAT (h): Repeats a desired
section or sequence.
• • • • • • b • • • • • •
c/v (SCAN): Searches
backward or forward.
C/V (SKIP): Goes to the
next or previous chapter / track /
file.
Z (STOP): Stops playback.
z (PLAY): Starts playback.
PRESET +/-: Selects programme
of Radio.
TUNING +/-: Tunes in the desired
radio station.
ENTER (b): Acknowledges menu
selection.
BACK (x): Exits the menu or
resumes playback. The resume
play function may not work
depending on the BD-ROM disc.
TITLE/POP-UP: Displays the DVD
title menu or BD-ROM’s pop-up
menu, if available.
DISC MENU: Accesses menu on a
disc.
• • • • • • d • • • • • •
Colored (R, G, Y, B) buttons:
Use to navigate on menus.
-B button : Selects mono/stereo in
FM mode.
M (PAUSE): Pauses playback.
MARKER: Marks any point during
playback.
SPEAKER LEVEL: Sets the sound
level of desired speaker.
SEARCH: Displays or exits the
search menu.
SOUND EFFECT: Selects a sound
effect mode.
SLEEP: Sets a certain period of
time after which the unit will
switch to off.
VOL +/-: Adjusts speaker volume.
Battery Installation
W/S/A/D (up/ down/ left/
right): Used to navigate on-screen
displays.
OPTICAL: Changes input mode to
optical directly.
X (REC): Records an audio CD.
TV Control Buttons
MUTE: Mute the unit.
• • • • • • c • • • • • •
HOME (n): Displays or exits the
[Home Menu].
Remove the battery cover on the
rear of the Remote Control, and
insert two R03 (size AAA) batteries
with 4 and 5 matched correctly.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 12
INFO/DISPLAY (m): Displays or
exits On-Screen Display.
2011-04-28 �� 10:19:16
Connecting
Attaching the speakers
to the unit
13
About Ferrite Core (for EMI only)
Be sure to attach the ferrite core to the speaker
cable (for connecting to this unit and wireless
receiver). This ferrite core can reduce noises.
To connect the cable to the unit, press each plastic
finger pad to open the connection terminals on the
unit. Insert the wire and release the finger pad.
How to attach the ferrite core
Connect the black stripe of each wire to the
terminals marked - (minus) and the other end to
the terminals marked + (plus).
2. Wind the speaker cables once on the ferrite
core.
1. Press the stopper [a] of the ferrite core to open.
2
Connecting
3. Close the ferrite core until it clicks.
Refer to the fig.3 and comment.
>>Caution
yy Be careful to make sure children not to put
their hands or any objects into the *speaker
duct.
*Speaker duct: A hole for plentiful bass
sound on speaker cabinet (enclosure).
yy The speakers contain magnet parts, so color
irregularity may occur on the TV screen or
PC monitor screen. Please use the speakers
far away from either TV screen or PC
monitor.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 13
Rear of wierless receiver
(fig. 3)
The length here
is as short as
possible.
2011-04-28 �� 10:19:17
14
System Setting
Settings
Adjust the Setup Settings
You can change the settings of the player in the
[Setup] menu.
1. Press HOME (n).
Resolution Setting
The player provides several output resolutions for
HDMI OUT and COMPONENT VIDEO OUT jack. You
can change the resolution using [Setup] menu.
1. Press HOME (n).
2. Use A/D to select the [Setup] and press ENTER
(b). The [Setup] menu appears.
3. Use W/S to select [DISPLAY] option then
press D to move to the second level.
4. Use W/S to select the [Resolution] option
then press ENTER (b) to move to the third level.
3
System Setting
2. Use A/D to select the [Setup] and press ENTER
(b). The [Setup] menu appears.
5. Use W/S to select the desired resolution then
press ENTER (b) to confirm your selection.
,,Note
3. Use W/S to select the first setup option, and
press D to move to the second level.
If your TV does not accept the resolution you
have set on the player, you can set resolution
to 576p(or480p) as follows:
Press Z (STOP) for more than 5 seconds.
4. Use W/S to select a second setup option, and
press ENTER (b) to move to the third level.
5. Use W/S to select a desired setting, and press
ENTER (b) to confirm your selection.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 14
2011-04-28 �� 10:19:18
System Setting
Wired Network Setup
If there is a DHCP server on the local area network
(LAN) via wired connection, this player will
automatically be allocated an IP address. After
making the physical connection, a small number of
home networks may require the player’s network
setting to be adjusted. Adjust the [NETWORK]
setting as follow.
15
5. The player will ask you to test the network
connection. Select [OK] and press ENTER (b) to
complete the network connection.
6. If you select [Test] and press ENTER (b) at
step 5 above, the network connection status is
displayed on the screen.
You can also test it on the [Connection Status]
in the [Setup] menu.
Preparation
Before setting the wired network, you need to
connect the broadband internet to your home
network.
1. Select [Connection Setting] option in the
[Setup] menu then press ENTER (b).
3
System Setting
2. Select [Yes] and press ENTER (b) to continue.
The new connection settings reset the current
network settings.
3. Use W/S/A/D to select the IP mode
between [Dynamic] and [Static].
Normally, select [Dynamic] to allocate an IP
address automatically.
,,Note
If there is no DHCP server on the network and
you want to set the IP address manually, select
[Static] then set [IP Address], [Subnet Mask],
[Gateway] and [DNS Server] using W/S/
A/D and numerical buttons. If you make a
mistake while entering a number, press CLEAR
to clear the highlighted part.
4. Select [OK] and press ENTER (b) to apply
network settings.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 15
2011-04-28 �� 10:19:18
16
Operating
General Playback
Playing a Disc
ert
Using [HOME] menu
1. Insert the disc.
The home menu appears when you press HOME
(n). Use A/D to select a category and press
ENTER (b).
a
b
c d
e f
For the most Audio CD, BD-ROM and DVD-ROM discs, playback starts automatically.
2. Press HOME (n).
3. Select [Movie] or [Music] using A/D, and press
ENTER (b).
4. Select [Blu-ray Disc], [DVD], [VR] or [Audio]
option using W/S, and press ENTER (b).
,,Note
When a disc is in the unit and the power is ON
,playback is not started automatically.
,,Note
4
a [Movie] - Plays video contents.
Operating
c [Music] - Plays audio contents.
b [Photo] - Plays photo contents.
d [NetCast] - Access to the NetCast Home.
e [Input] - Changes input mode
f [Setup] - Adjusts the system settings.
yy Playback functions described in this manual
are not always available in every file and
media. Some functions can be restricted
depending on many factors.
yy Depending on the BD-ROM titles, a USB
device connection may be needed for the
proper playback.
yy Unfinalized DVD VR format discs may not be
played in this player.
yy Some DVD-VR discs are made with CPRM
data by DVD RECORDER. This unit cannot
support these kinds of discs.
Playing a file on a disc/USB
device
yui
This player can play video, audio and photo files
contained in the disc or USB device.
1. Press HOME (n).
2. Select [Movie], [Photo] or [Music] using A/D,
and press ENTER (b).
3. Select [Data] or [USB] option using W/S, and
press ENTER (b).
4. Select a file using W/S/A/D, and press d
(PLAY) or ENTER (b) to play the file.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 16
2011-04-28 �� 10:19:18
Operating
Basic operations for video and
audio content
17
On-Screen display
To stop playback
You can display and adjust various information and
settings about the content.
Press Z (STOP) while playback.
eroy
To pause playback
1. While playback, press INFO/DISPLAY (m) to
show various playback information.
Press M (PAUSE) while playback.
Press d (PLAY) to resume playback.
To play frame-by-frame (video)
Press M (PAUSE) while movie playback.
Press M (PAUSE) repeatedly to play Frame-by-Frame
playback.
To scan forward or backward
Press c or v to play fast forward or fast reverse
during playback.
4
To slow down the playing
speed(video)
a Title – current title number/total number of
titles
While the playback is paused, press v repeatedly
to play various speeds of slow motion.
b Chapter – current chapter number/total
number of chapters
To skip to the next/previous
chapter/track/file
c Time – elapsed playing time/total playback
time
During playback, press C or V to go to the
next chapter/track/file or to return to the beginning
of the current chapter/track/file.
Press C twice briefly to step back to the previous
chapter/track/file.
In the file list menu of a server, there may have
many types of contents in a folder together. In this
case, press C or V to go to the previous or
next content with same type.
Operating
You can change the various playback speeds by
pressing c or v repeatedly.
d Audio – selected audio language or channel
e Subtitle – selected subtitle.
f Angle – selected angle/total number of
angles
g TV Aspect Ratio – selected TV aspect Ratio
h Picture Mode – selected picture mode
2. Select an option using W/S.
3. Use A/D to adjust the selected option value.
4. Press BACK(x) to exit the On-Screen display.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 17
2011-04-28 �� 10:19:19
5
18
Troubleshooting
Troubleshooting
Troubleshooting
Symptom
Cause & Solution
The Power does not turned on.
Plug the power cord into the wall outlet securely.
The unit does not start
playback.
yy Insert a playable disc. (Check the disc type, colour system, and
regional code.)
yy Place the disc on the disc slot correctly.
yy Clean the disc.
yy Cancel the Rating function or change the rating level.
The angle cannot be changed.
Multi-angles are not recorded on the DVD Video being played.
Cannot play movie, photo or
music files.
yy The files are not recorded in a format that the unit can play.
The remote control does not
work properly.
yy The remote control is not pointed at the remote sensor of the unit.
yy The unit does not support the codec of the movie file.
yy The remote control is too far from the unit.
yy There is an obstacle in the path of the remote control and the unit.
yy The batteries in the remote control are exhausted.
The unit is plugged in, but the
power will not turn on or off.
5
Troubleshooting
The unit is not operating
normally.
There is no picture.
You can reset the unit as follows.
Unplug the power cord, wait at least five seconds, and then plug it in
again.
yy Select the appropriate video input mode on the TV so the picture
from the unit appears on the TV screen.
yy Connect the video connection securely.
yy Check the [HDMI Color Setting] in the [Setup] menu is set to the
appropriate item that conforms to your video connection.
yy Your TV may not suppot the resolution you have set on the player.
Change the resolution that your TV accepts.
yy The player’s HDMI OUT jack is connected to a DVI device that does
not support copyright protection.
Picture noise appears.
yy You are playing a disc recorded in a colour system that is different
from your TV.
yy Set the resolution which your TV accepts.
Blu-ray 3D disc playback does
not output 3D views.
yy Connect the player to your TV with HDMI cable (Type A, High Speed
HDMI™ Cable).
yy Your TV may not support “HDMI 1.4 3D mandatory format”.
yy The [3D Mode] option in the [Setup] menu is set to [Off ]. Set the option to [On].
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 18
2011-04-28 �� 10:19:19
Troubleshooting
Symptom
Cause & Solution
BD-Live feature does not work.
yy The connected USB storage may not have enough space. Connect
the USB storage with at least 1GB free space.
19
yy Ensure that the unit is correctly connected to the local area network
and can access the internet.
yy Your broadband speed may not fast enough to use the BD-Live
features. Contact your Internet Service Provider (ISP) and increase the
broadband speed is recommended.
yy The [BD-LIVE connection] option in the [Setup] menu is set to
[Prohibited]. Set the option to [Permitted].
Streaming video services (such
as YouTube™, etc.) are often
stopped or “buffer” during
playback.
Your broadband service speed may not be fast enough to stream video
services. Contact your Internet Service Provider (ISP) and increase the
broadband speed is recommended.
Shared folder or files from
media server are not displayed
on the device list.
The player is not connected to the local area network that your media
server are connected.
There is no sound or the sound
is distorted.
yy The unit is in scan, slow motion, or pause mode.
yy The sound volume is low.
yy Check the speaker cable connection.
Customer Support
Open source software notice
To obtain the corresponding source code under GPL, LGPL and other open source licenses, please visit
http://opensource.lge.com. All referred license terms, warranty disclaimers and copyright notices are
available to download with the source code.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 19
5
Troubleshooting
You can update the Player using the latest software to enhance the products operation and/or add new
features. To obtain the latest software for this player (if updates have been made), please visit http://lgservice.com or contact LG Electronics customer care centre.
2011-04-28 �� 10:19:19
20 Appendix
Trademarks and
Licenses
Blu-ray Disc™, Blu-ray™, Blu-ray 3D™, BD-Live™,
BONUSVIEW™ and the logos are trademarks of
the Blu-ray Disc Association.
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
iPhone is a trademark of Apple Inc. “Made
for iPod” and “Made for iPhone” mean that
an electronic accessory has been designed
to connect specifically to iPod or iPhone
respectively, and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards. Please note that the use of this accessory with
iPod, iPhone may affect wireless performance.
Java and all Java-based trademarks and logos
are trademarks or registered trademarks of Sun
Microsystems, Inc. in the United States and other
countries.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
6
Appendix
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 20
2011-04-28 �� 10:19:20
Appendix
21
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,392,195; 7,272,567;
7,333,929; 7,212,872 & other U.S. and worldwide
patents issued & pending. DTS and the Symbol
are registered trademarks,& DTS-HD, DTS-HD
Master Audio | Essential and the DTS logos
are trademarks of DTS, Inc. Product includes
software. © DTS, Inc. All Rights Reserved.
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
DLNA®, the DLNA Logo and DLNA CERTIFIED® are
trademarks, service marks, or certification marks
of the Digital Living Network Alliance.
“x.v.Color” is a trademark of Sony Corporation.
6
Appendix
“AVCHD” and the “AVCHD” logo are trademarks of
Panasonic Corporation and Sony Corporation.
DivX®, DivX Certified® and associated logos
are trademark of DivX, Inc., and are used under
license.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 21
2011-04-28 �� 10:19:20
22 Appendix
Specifications
General
Power requirements
Refer to main label.
Power consumption
Refer to main label.
Dimensions (W x H x D)
135 X 295 X 315 mm without foot
Net Weight (Approx.)
3.9 kg
Operating temperature
41 °F to 95 °F (5 °C to 35 °C)
Operating humidity
5 % to 90 %
Inputs/Outputs
VIDEO OUT
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
HDMI OUT (video/audio)
19 pin (Type A, HDMI™ Connector)
COMPONENT VIDEO OUT
(Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
DIGITAL IN (OPTICAL)
3 V (p-p), Optical jack x 1
PORT. IN
0.5 Vrms (3.5 mm stereo jack)
Tuner
FM Tuning Range
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
Amplifier
Stereo mode
80 W + 80 W (4Ω at 1kHz)
6
Appendix
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 22
2011-04-28 �� 10:19:20
Appendix 23
System Laser
Semiconductor laser
Wavelength
405 nm / 650 nm
Signal system
Standard NTSC/PAL colour TV system
Frequency response
20 Hz to 20 kHz (48 kHz, 96 kHz, 192 kHz sampling)
Signal-to-noise ratio
More than 80 dB Total harmonic distortion
0.05 % at 1 W
Dynamic range
More than 85 dB
LAN port
Ethernet jack x 1, 10BASE-T/100BASE-TX
Bus Power Supply
USB DC 5 V 0 500 mA
iPod DC 5 V 0 1 A
Speakers
Front speaker (Left/ Right)
Type
3 Way 4 speaker
Max. Input power
160 W
Impedance Rated
4Ω
Net Dimensions (W x H x D)
126 X 295 X 315 mm
Input Power
80 W
Net Weight
4.35 kg
yy Design and specifications are subject to change without notice.
6
Appendix
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 23
2011-04-28 �� 10:19:20
An extended Owner's Manual that contains
information on the advanced features is located
on the CD-ROM provided in an electronic version.
To read these files, you will need to use a Personal
Computer (PC) equipped with a CD-ROM drive.
FX166-F0F_DSGPLL_SIM_ENG_4931.indd 24
2011-04-28 �� 10:19:20
Download PDF