LG | LHD657M | LG LHD657M Owner’s Manual

OWNER’S MANUAL
DVD Home
Theater
System
Please read this manual carefully before operating
your set and retain it for future reference.
LHD657M (LHD657M, S67T4-S, S67T4-C, S67T2-W)
*MFL69677616*
www.lg.com
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, should be placed on the
apparatus.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not use high voltage products around
this product. (ex. Electrical swatter) This product may
malfunction due to electrical shock.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of
the product and to protect it from over heating.
The openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance, contact
an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a
dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact
replacement part by an authorized service center.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention to
plugs, wall outlets, and the point where the cord exits
the appliance. The Power Plug is the disconnecting
device. In case of an emergency, the Power Plug must
remain readily accessible.
Getting Started
3
This device is equipped with a portable battery or
accumulator.
NOTICE: For safety marking information including
product identification and supply ratings, please refer
to the main label on the bottom or the other surface
of the product.
CAUTION: No naked flame sources, such as lighted
candles, should be placed on the apparatus.
Symbols
~
0
Refers to alternating current(AC).
Refers to direct current(DC).
Refers to class II equipment.
1
Refers to stand-by.
!
Refers to “ON” (power).
Refers to dangerous voltage.
1
Getting Started
Safety way to remove the battery or the battery
from the equipment: Remove the old battery or
battery pack, follow the steps in reverse order than
the assembly. To prevent contamination of the
environment and bring on possible threat to human
and animal health, the old battery or the battery
put it in the appropriate container at designated
collection points. Do not dispose of batteries or
battery together with other waste. It is recommended
that you use local, free reimbursement systems
batteries and accumulators. The battery shall not be
exposed to excessive heat such as sunshine, fire or
the like.
4
Table of Contents
Table of Contents
1
Getting Started
2
Safety Information
4
Table of Contents
6
Unique Features
6
– Portable In
6
– USB Direct Recording
6
– Full HD up-scaling
6
– Home Theater Speaker ez Setup
6 – Bluetooth®
7Introduction
7
– Playable Discs
7
– About the “7” Symbol Display
7
– Symbols Used in this Manual
7
– Regional Codes
8
Playable file Requirement
9
Remote control
10 Front panel
11 Rear panel
2Connecting
12
14
15
16
16
16
17
18
18
19
19
20
20
20
20
21
21
21
22
Assembling the speaker
Attaching the speakers to the unit
Positioning the system
How to Affix the Ferrite Core
– Affix the Ferrite Core for HDMI cable
Connections to Your TV
– HDMI Out Connection
– What is SIMPLINK?
– Video Connection
– Resolution Setting
Video Output Resolution
Optional Equipment Connection
– AUX (L/R) INPUT Connection
– PORT. IN (Portable Input) Connection
– Listening to music from your portable
player or external device
– USB Connection
– OPTICAL IN connection
– Home theater speaker ez setup
– Antenna Connection
3
System Setting
23
23
23
24
24
25
26
Adjust the setup settings
– OSD Initial language settings - Optional
– To display and exit the Setup menu
– Language
– Display
– Audio
– Lock (Parental Control)
Table of Contents
4Operating
5Troubleshooting
27
27
28
28
28
28
28
28
28
28
29
29
30
31
31
31
31
31
31
32
32
32
33
33
33
33
33
33
34
34
34
35
35
36
36
38
38
39Troubleshooting
Using the Home Menu
Basic Operations
Other Operations
– Displaying Disc Information on-screen
– To display the DVD Menu
– To display the DVD title
– 1.5 times speed playback
– Screen Saver
– Starting play from selected time
– Resume playback
– Changing subtitle code page
– Marked Playback
– Viewing a PHOTO file
– Sleep Timer Setting
– Dimmer
– Turn off the sound temporarily
– Last Scene Memory
– Power Resume - Optional
– System Select - Optional
– Adjust the speaker level settings
– VOCAL FADER
– Auto power down
Radio Operations
– Listening to the radio
– Presetting the Radio Stations
– Deleting all the saved stations
– Deleting a saved station
– Improving poor FM reception
Sound adjustment
– Setting the surround mode
– Setting the USER EQ
Advanced Operations
– Recording to USB
Using a Bluetooth wireless technology
– Listening to music of a Bluetooth device
Auto function change
AUTO POWER On
5
1
6Appendix
2
40Maintenance
40 – Handling the Unit
40 – Notes on Discs
41 Area Code List
42 Language code List
43 Trademarks and Licenses
44Specifications
3
4
5
6
6
Getting Started
Unique Features
1
Portable In
Getting Started
Listen to music from your portable device. (MP3,
Notebook, etc.)
USB Direct Recording
Records music from CD to your USB device.
Full HD up-scaling
Views Full HD picture quality with simple setup.
Home Theater Speaker ez Setup
Listen to sounds from TV, DVD and Digital device with
vivid 5.1 (2.1 or 2.0) ch mode.
Bluetooth®
Listens to music stored on your Bluetooth device.
Getting Started
Introduction
Playable Discs
DVD-VIDEO (8 cm/12 cm disc)
Discs such as movies that can be
purchased or rented.
DVD±R (8 cm/12 cm disc)
Video mode and finalized only.
DVD-RW (8 cm/12 cm disc)
Video mode and finalized only.
DVD+R: Video mode only
Supports the double layer disc also.
DVD+RW (8 cm/12 cm disc)
Video mode and finalized only.
Audio CD: Music CDs or CD-R/CDRW in music CD format that can be
purchased.
About the “7” Symbol Display
“7” may appear on your TV display during operation
and indicates that the function explained in this
owner’s manual is not available on that specific
media.
Symbols Used in this Manual
r
DVD-Video, DVD±R/RW in Video
mode or VR mode and finalized
t
Audio CDs
y
Video files contained in the USB/
Disc
u
Audio files contained in the USB/
Disc
i
Photo files contained in the USB/
Disc
,,Note
Indicates special notes and operating features.
,,Tip
Indicates tip and hints for making the task easier.
>>Caution
Indicates cautions for preventing possible damages
from abuse.
Regional Codes
This unit has a regional code printed on the unit.
This unit can play only DVD discs labeled same as the
unit or “ALL”.
yy Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your unit’s regional code or
the disc cannot play.
yy If you try to play a DVD with a different regional
code from your unit, the message “Check Regional
Code” appears on the TV screen.
1
Getting Started
This unit plays DVD±R/RW and CD-R/RW that
contains audio titles, MP3, WMA and/or JPEG files.
Some DVD±RW/DVD±R or CD-RW/CD-R cannot
be played on this unit due to the recording quality or
physical condition of the disc, or the characteristics of
the recording device and authoring software.
7
8
Getting Started
Playable file
Requirement
1
Getting Started
Music file requirement
MP3/ WMA file compatibility with this unit is limited
as follows :
yy Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
yy Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
yy Support Version : v2, v7, v8, v9
yy Maximum files : Under 999
yy File extensions : “.mp3”/ “.wma”
yy CD-ROM file format : ISO9660/ JOLIET
yy We recommend that you use Easy-CD Creator,
which creates an ISO9660 file system.
yy You have to set the disc format option to
[Mastered] in order to make the discs compatible
with the LG players when formatting rewritable
discs. When setting the option to Live File System,
you cannot use it on LG players.(Mastered/ Live
File System : Disc format system for Windows
Vista)
Video file requirement
Video file compatibility with this unit is limited as
follows :
yy Available resolution: within 720 x 576 (W x H)
pixels.
yy The file name of the Video subtitle should be
entered within 45 characters.
yy If there is impossible code to express in the Video
file, it may be displayed as “ _ “ mark on the display.
yy Frame rate : less than 30 fps.
yy If the video and audio structure of recorded files is
not interleaved, either video or audio is outputted.
yy Playable Video file : “.avi”, “.mpg”, “.mpeg”
yy Playable Subtitle format : SubRip (*.srt/ *.txt),
SAMI (*.smi), SubStation Alpha (*.ssa/ *.txt),
MicroDVD (*.sub/ *.txt), SubViewer 2.0 (*.sub/
*.txt), Vobsub (*.sub)
yy Playable Codec format :
“Xvid”, “MPEG-1”, “MPEG-2”
yy Playable Audio format : “AC3”, “PCM”, “MP3”,
“WMA”,
yy Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
yy Bit rate : within 32 to 320 kbps (MP3), 40 to 192
kbps (WMA)
The DTS is not supported. In case of DTS audio
format, audio is not output.
yy For Discs formatted in Live file system, you can not
it on this unit.
Photo file requirement
yy If the name of movie file is different from that of
the subtitle file, during playback of a Video file,
subtitle may not be display.
Photo file compatibility with this unit is limited as
follows :
yy Max pixel in width : 2760 x 2048 pixel
yy Maximum files : Under 999
yy Some discs may not operate due to a different
recording format or the condition of disc.
yy File extensions: “.jpg”
yy CD-ROM file format : ISO9660/ JOLIET
yy If you play a Xvid file differ from Xvid spec, it may
not operate normally.
yy If you play GMC video file which is more than
1-warp point, video playback screen will not
smooth.
Getting Started
9
Remote control
MARKER : Marks play list.
n (Home) : Displays the [Home
Menu].
• • • • • • • • • b• • • • • • • •
m INFO/DISPLAY : Accesses OnScreen Display.
SOUND EFFECT : Selects a sound
effect mode.
VOL -/+ (Volume) : Adjusts speaker
volume.
(Mute) : Mutes the sound.
X REC : USB Direct Recording.
0-9 numerical buttons : Selects
numbered options in a menu.
h REPEAT : Selects a play
mode. (Repeat/ Random)
W/S/A/D (up/ down/ left/
right) : Used to navigate on-screen
displays.
CLEAR : Removes a number when
setting the password.
TUNING +/- : Tunes in the desired
radio station.
b ENTER : Acknowledges menu
selection.
Presetting the radio stations.
x RETURN : Moves backwards
in the menu or exits the setup
menu.
TITLE : If the current DVD title has
a menu, the title menu appears
on the screen. Otherwise, the disc
menu may not appear.
• • • • • • • • • c• • • • • • • •
Remove the battery cover on the
rear of the remote control, and
insert the battery with 4 and 5
matched correctly.
Z (Stop) : Stops playback.
• • • • • • • • • a• • • • • • • •
1 (Standby/On) : Switches the
unit ON or OFF.
C/V (Skip) : Goes to the
next or previous chapter / track /
file.
B (Open/Close) : Opens and closes
the disc tray.
c/v (Scan) : Searches
backward or forward.
P FUNCTION : Selects the
function and input source.
SPEAKER LEVEL : Sets the sound
level of desired speaker.
DISC MENU : Accesses the menu
on a DVD disc.
PRESET (W/S) : Selects
programme of Radio.
Replacement of battery
• • • • • • • • • d• • • • • • • •
d (Play) MONO/STEREO : Starts
playback. Selects Mono/ Stereo.
M (Pause/Step) : Pauses playback.
• • • • • • • • • e• • • • • • • •
TV Control buttons : Controls the
TV. (LG TV only)
-- You can control the sound
level, input source, and power
switching of LG TVs as well.
Hold 1 (TV) and press PR/CH
(W/S) button repeatedly until
the TV turns on or off.
OPTICAL : Changes input source to
optical directly.
? : This button is not available.
MIC VOL -/+ (Microphone Volume)
: Adjusts microphone volume.
ECHO VOL -/+ (Volume) : Adjusts
echo volume.
VOCAL FADER : You can enjoy the
function as karaoke, by reducing
singer vocal of music in the various
source.
1
Getting Started
SLEEP : Sets the System to turn
off automatically at a specified
time.
(Dimmer : The display window will
be darken by half.)
10 Getting Started
Front panel
1
Getting Started
a Disc Tray
b Display window
Shows the current status of the unit.
c Microphone jacks 1/2
d PORT. IN
Connects to a portable player with audio
outputs.
e USB Port
Connects a USB device.
f R (Open/Close)
Opens or closes the disc tray.
g T (Play/Pause)
-- Starts playback.
-- Pauses playback temporarily, press again to exit
pause mode.
h I (Stop)
Stops playback.
iF (Function)
Changes the input source or function.
j -/+(Volume)
Adjusts speaker volume.
k 1/! (Standby/On)
Switches the unit ON or OFF.
Getting Started 11
Rear panel
1
Getting Started
a Power cord
b Speaker connectors
Connects the speaker cables.
c OPTICAL IN
Connects to optical audio equipment.
d HDMI OUT TO TV
Connects to TV with HDMI inputs.
(Interface for digital audio and video)
e VIDEO OUT
Connects to a TV with video inputs.
f AUX (L/R) INPUT
Connects to an external source with 2 channel
audio outputs.
g ANTENNA FM
FM- Connects the FM wired antenna.
12 Connecting
Assembling the speaker
2. Draw the speaker cord through the hole on the
base.
Before connecting the speakers, assemble the
speakers. Please check the items for assembling the
speakers.
Preparation
2
Connecting
Pole
Base
Screw
Speaker
Speaker cables
1. Attach the pole to the base, then secure the
connection with a supplied screw.
,,Note
Make sure speaker cable unfolded or in straight
condition before insert it to the hole.
Connecting 13
3. Attach the speakers to the speaker stands by
rotating the screws.
4. Connect the speaker wire to the terminal on the
speaker. Make sure the wire marked black goes in
to the terminal marked “-”(minus) and the other
wire goes in to the terminal marked “+”(plus).
2
Connecting
,,Note
Do not catch the speaker cord between speaker
and the pole.
>>Caution
Be careful that the speaker
does not fall down. Otherwise
it may result in the speaker
malfunction and cause
personal injury and/ or
property damage.
14 Connecting
Attaching the speakers
to the unit
2
Connecting
1. Connect the wires to the unit.
Match each wire’s colored band to the same
colored connection terminal on the rear of the
unit.
To connect the cable to the unit, press each
plastic finger pad to open the connection
terminal. Insert the wire and release the finger
pad.
Color
Speaker
Position
Grey
Rear
Rear right
Blue
Rear
Rear left
Green
Center
Center
Orange
Subwoofer
Any front position
Red
Front
Front right
White
Front
Front left
To connect the cable to the speakers, press each
plastic finger pad to open the connection terminals
on the base of each speaker. Insert the wire and
release the finger pad.
>>Caution
Connect the black stripe of each wire to the
terminals marked -(minus) and the other end to
the terminals marked + (plus).
Connect a woofer cord to the player. When
connecting a woofer cord to the player, insert
the connector until it clicks.
yy Be careful to make sure children do not put
their hands or any objects into the *speaker
duct.
*speaker duct : A hole for plentiful bass sound
on speaker cabinet (enclosure).
yy Place the center speaker at a safe distance
from the child’s reach. Otherwise it may result
in the speaker falling down and causing
personal injury and/or property damage.
yy The speakers contain magnet parts, so color
irregularity may occur on the TV screen or PC
monitor screen. Please use the speakers far
away from either TV screen or PC monitor.
yy Before using the subwoofer, remove the
protective vinyl.
2. Connect the wires to the speakers.
Connect the other end of each wire to the correct
speaker according to the color coding:
Connecting 15
Positioning the system
The following illustration shows an example of
positioning the system. Note that the illustrations
in these instructions differ from the actual unit for
explanation purposes.
For the best possible surround sound, all the speakers
other than the subwoofer should be placed at the
same distance from the listening position ( ).
Front left speaker (L) / Front right speaker (R) :
Place the front speakers to the sides of the
monitor or screen and as flush with the screen
surface as possible.
Center speaker: Place the center speaker above or
below the monitor or screen.
Surround left speaker (L) / Surround right
speaker (R) :
Place these speakers behind your listening
position, facing slightly inwards.
Unit
2
Connecting
ubwoofer: The position of the subwoofer is not
S
so critical, because low bass sounds are not highly
directional. But it is better to place the subwoofer
near the front speakers. Turn it slightly toward the
center of the room to reduce the wall reflections.
16 Connecting
How to Affix the Ferrite
Core
Ferrite core may not be provided depending on each
nation’s regulations.
2
Affix the Ferrite Core for HDMI
cable
Connecting
You must affix a ferrite core in order to reduce or
eliminate electrical interference.
1. Pull the stopper [a] of the ferrite core to open.
2. Wind the HDMI cable around the ferrite core
once.
3. Close the ferrite core until it clicks.
Connections to Your TV
Make one of the following connections, depending on
the capabilities of your existing equipment.
,,Note
yy Depending on your TV and other equipment
you wish to connect, there are various ways
you could connect the player. Use only one of
the connections described in this manual.
yy Please refer to the manuals of your TV, Stereo
System or other devices as necessary to
make the best connections.
>>Caution
yy Make sure the unit is connected directly to
the TV. Tune the TV to the correct video input
channel.
yy Do not connect your player via your VCR.
The image could be distorted by the copy
protection system.
Connecting 17
HDMI Out Connection
If you have a HDMI TV or monitor, you can connect it
to this unit using a HDMI cable (Type A, High Speed
HDMI™ Cable).
Connect the HDMI OUT jack on the unit to the HDMI
IN jack on a HDMI compatible TV or monitor.
Set the TV’s source to HDMI (refer to TV’s Owner’s
manual).
>>Caution
yy Changing the resolution when the connection
has already been established may result in
malfunctions. To solve the problem, turn off
the unit and then turn it on again.
yy When the HDMI connection with HDCP is
not verified, TV screen is changed to black or
green screen or the snow noise may occur
on the screen. In this case, check the HDMI
connection, or disconnect the HDMI cable.
yy When you connect a HDMI or DVI compatible
device make sure of the following:
,,Tip
yy You can fully enjoy digital audio and video
signals together with this HDMI connection.
yy When you use HDMI connection, you can
change the resolution for the HDMI output.
(Refer to “Resolution Setting” on page 19.)
- Try switching off the HDMI/DVI device and
this unit. Next, switch on the HDMI/DVI
device and leave it for around 30 seconds,
then switch on this unit.
- The connected device’s video input is set
correctly for this unit.
- The connected device is compatible with
720 x 480i (or 576i), 720 x 480p (or 576p),
1280 x 720p, 1920 x 1080i or 1920 x
1080p video input.
yy Not all HDCP-compatible HDMI or DVI devices
will work with this unit.
- The picture will not be displayed properly
with non-HDCP device.
- This unit does not playback and TV screen
is changed to black or green screen or the
snow noise may occur on the screen.
yy If there is noise or lines on the screen, please
check the HDMI cable and use a higher
version cable than High Speed HDMI™ Cable.
yy If you use Bluetooth or AUX-OPT Function of
the unit, the audio is not output to HDMI.
Connecting
,,Note
yy If a connected HDMI device does not accept
the audio output of the unit, the HDMI
device’s audio sound may be distorted or may
not output.
2
18 Connecting
What is SIMPLINK?
Video Connection
Connect the VIDEO OUT jack on the unit to the video
in jack on the TV using a video cable.
Some functions of this unit are controlled by the
TV’s remote control when this unit and LG TV’s with
SIMPLINK are connected through HDMI connection.
2
You can hear the sound through the system’s
speakers.
Controllable functions by LG TV’s remote control;
Power on/off, volume up/down, mute, etc.
Connecting
Refer to the TV owner’s manual for the details of
SIMPLINK function.
LG TV’s with SIMPLINK function has the logo as
shown above.
,,Note
yy Depending on the disc type or playing status,
some SIMPLINK operation may differ from
your purpose or not work.
yy The function is automatically changed to
optical when you change the speaker setting
of simplink to external, no matter what kind
of the function you are using.
Yellow
Connecting 19
Resolution Setting
The unit provides several output resolutions for HDMI
OUT.
You can change the resolution using [Setup] menu.
1. Press n.
2. Use A/D to select the [Setup] and press
b ENTER. The [Setup] menu appears.
Video Output
Resolution
Displayed resolution in display window and outputted
resolution may different according to connection
type.
[HDMI OUT] : 1080p, 1080i, 720p and 480p (or
576p) and 480i (or 576i)
[VIDEO OUT] : 480i (or 576i)
2
Connecting
3. Use W/S to select [Display] option then press
D to move to the second level.
4. Use W/S to select the [Resolution] option then
press D to move to the third level.
5. Use W/S to select the desired resolution then
press b ENTER to confirm your selection.
,,Note
If your TV does not accept the resolution you
have set on the player, you can set resolution to
480p (or 576p) as follows:
Press Z for more than 5 seconds.
20 Connecting
Optional Equipment
Connection
PORT. IN (Portable Input)
Connection
Connect an output of portable device (MP3 or PMP
etc.) to the PORT. IN connector.
AUX (L/R) INPUT Connection
Connect an Output of auxiliary device to the AUX (L/
R) INPUT Connector.
2
Connecting
MP3 player, etc...
Listening to music from your
portable player or external
device
The unit can be used to play the music from many
types of portable player or external devices.
To the audio output jacks of
your component
(TV, VCR, etc.)
1. Connect the portable player to the
PORT. IN (PORTABLE IN) connector of the unit.
Red
White
,,Note
If your TV has only one output for audio (mono),
connect it to the left (white) audio jack on the
unit.
Or
Connect the external device to the AUX (L/R)
INPUT connector of the unit.
2. Turn the power on by pressing 1/!.
3. Select the PORTABLE or AUX function by
pressing P FUNCTION.
4. Turn on the portable player or external device and
start it playing.
Connecting 21
USB Connection
OPTICAL IN connection
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the unit.
Connect an optical output of Unit (or Digital Device
etc) to the OPTICAL IN connector.
2
Connecting
,,Note
To the digital
optical output jack of
your component
Removing the USB Device from the unit.
1. Choose a different function mode or press Z
twice in a row.
2. Remove the USB device from the unit.
Compatible USB Devices
yy MP3 Player : Flash type MP3 player.
yy USB Flash Drive :Devices that support USB2.0 or
USB1.1.
yy The USB function of this unit does not support
some USB devices.
USB device requirement
yy Devices which require additional program
installation connected to a computer, are not
supported.
yy Do not extract the USB device while in operation.
yy For a large capacity USB, it may take longer than a
few minute to be searched.
yy To prevent data loss, back up all data.
yy If you use a USB extension cable or USB hub, the
USB device is not recognized.
yy Using NTFS file system is not supported. (Only
FAT(16/32) file system is supported.)
yy This unit is not supported when the total number
of files is 1000 or more.
yy External HDD, Card readers, Locked devices, or hard type usb devices are not supported.
yy USB port of the unit cannot be connected to PC.
The unit can not be used as a storage device.
yy Some USB may not work with this unit.
Home theater speaker ez setup
Listen to sound from TV, DVD and Digital Device with
5.1(2.1 or 2)ch mode. Even in power off mode, if you
press OPTICAL, then power is on and automatically
changed to AUX OPT mode.
1. Connect the unit’s OPTICAL IN jack to jack on
optical out of your TV (or Digital Device etc.).
2. Select the AUX OPT by using the OPTICAL on the
remote control to select the AUX OPT directly.
Or
To select the AUX OPT function, press
P FUNCTION on the remote control.
3. Listen sound with 5.1(2.1 or 2)ch speaker.
4. To escape from AUX OPT by using the OPTICAL.
Function is retuned to previous one.
22 Connecting
Antenna Connection
Connect the supplied FM antenna for listening to the
radio.
Connect the FM Wire antenna to the FM antenna
connector.
2
Connecting
,,Note
Be sure to fully extend the FM wire antenna.
System Setting 23
Adjust the setup
settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
To display and exit the Setup
menu
1. Press n.
Displays the [Home Menu].
You can also set a language for the subtitles and the
Setup menu, among other things. For details on each
Setup menu item, see pages 23 to 26.
OSD Initial language settings Optional
1. Press 1(POWER) to turn the unit on. The
language setup menu will appear on the screen.
2. Use WSAD to select a language then press
b ENTER.
The confirm menu will appear.
3. Use AD to select the [Enter] then press
b ENTER to finish the language setup.
3. Press b ENTER.
Displays the [Setup].
4. Press n or x RETURN to exit in the [Setup]
Menu.
About help menu for Setup
Menu
ws
Buttons
Operation
WS
Moving to another
menu.
a
Move
A
Moving to previous
level.
d
Move
D
Moving to next level
or selecting menu.
x RETURN
To exit the [Setup]
menu or
[ 5.1 Speaker Setup].
Move
x
Close
b
Select
b ENTER
To confirm menu.
3
System Setting
During the first use of this unit, the initial language
setup menu appears on your TV screen. You must
complete initial language selection before using the
unit. English will be selected as the initial language.
2. Select an [Setup] by using AD.
24 System Setting
Language
Resolution
Menu Language
Sets the output resolution of HDMI video signal.
Refer to “Resolution Setting” for details about the
resolution (Refer to the page 19).
Select a language for the Setup menu and on screen
display.
Disc Audio / Disc Subtitle / Disc Menu
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
[Original]
Refers to the original language in which the disc
was recorded.
3
[Other]
System Setting
To select another language, press numeric
buttons and then b ENTER to enter the
corresponding 4-digit number according to the
language code list on the page 42. If you
enter the wrong language code, press CLEAR.
[Off (for Disc Subtitle)]
Turns off Subtitle.
[Auto]
If the HDMI OUT jack is connected to
TVs providing display information (EDID),
automatically selects the resolution best suited
to the connected TV. If VIDEO OUT is only
connected, this changes the resolution to 480i
(or 576i) as default resolution.
[1080p]
Outputs 1080 lines of progressive video.
[1080i]
Outputs 1080 lines of interlaced video.
[720p]
Outputs 720 lines of progressive video.
[480p (or 576p)]
Outputs 480 (or 576) lines of progressive video.
[480i (or 576i)]
Display
TV Aspect
Select the screen aspect to use based on the shape
of your TV screen.
[4:3]
Select when a standard 4:3 TV is connected.
[16:9]
Select when a 16:9 wide TV is connected.
Display Mode
The Display Mode setting works only when the TV
Aspect mode is set to 4:3.
[Letterbox]
Displays a wide picture with bands on the upper
and lower portions of the screen.
[Panscan]
Automatically displays the wide picture on the
entire screen and cuts off the portions that do
not fit. (If the disc/file is not compatible with Pan
Scan, the picture is displayed at Letterbox ratio.)
Outputs 480 (or 576) lines of interlaced video.
System Setting 25
Audio
DRC (Dynamic Range Control)
5.1 Speaker Setup
Make the sound clear when the volume is turned
down (Dolby Digital only). Set to [On] for this effect.
Make the following settings for the built-in 5.1
channel surround decoder.
Vocal
1. Select [5.1 Speaker Setup] on the [Audio] menu.
Select [On] to mix karaoke channels into normal
stereo.
2. Press b ENTER.
The [5.1 SPEAKER] appears.
This function is effective for multi-channel karaoke
DVDs only.
HD AV Sync
5. Returns to the previous menu by pressing
x RETURN.
Semi Karaoke
3. Use AD to select the desired speaker.
[Speaker]
Select a speaker that you want to adjust.
,,Note
Certain speaker settings are prohibited by
the Dolby Digital licensing agreement.
When a chapter/ title/ track is fully finished, this
function shows the score in the screen with a fanfare
sound.
[On]
When you finished singing a score will appear on
the screen.
[Size]
[Off]
Since the speaker settings are fixed, you cannot
change the settings.
Fanfare and score do not appear on the screen.
[Volume]
Adjust the output level of each speaker.
[Distance]
Adjust the distance between each speaker and
the listening position.
[Speaker Test Start]
Select [Speaker Test Start] by using the WS
and press b ENTER.
Press b ENTER again to stop.
Adjust the volume to match the volume of test
signals memorized in the system.
,,Note
VD, DVD Karaoke discs with more than 2
yy D
tracks are available discs for the this function.
hen you watch movies, “off ” the Semi
yy W
Karaoke at the SETUP menu or enjoy it
without connecting the MIC if the fanfare or
score appears during changing a chapter.
yy T his function operate on the DVD/CD mode.
yy The Semi Karaoke function is available only
when a microphone is connected.
yy If you do not use the microphone, turn down
the volume and disconnect the microphone.
3
System Setting
4. Adjust options using WSAD buttons.
Sometimes Digital TV encounters a delay between
picture and sound. If this happens you can
compensate by setting a delay on the sound so that
it effectively ‘waits’ for the picture to arrive: this is
called HD AV Sync. Use WS (on the remote control)
to scroll up and down through the delay amount,
which you can set at anything between 0 and
300ms.
26 System Setting
Lock (Parental Control)
Password
You can enter or change password.
Initial Setting the Area Code:
When you use this unit for the first time, you have to
set the Area Code.
2. Press b ENTER.
1. Select the [Lock] menu and then press D.
3. Input a password and press b ENTER.
2. Press D.
To access the [Lock] options, you must input the
password you have created. Input a password and
press b ENTER. Enter it again and press
b ENTER to verify. If you make a mistake before
pressing b ENTER, press CLEAR.
3. Select the first character using WS buttons.
3
1. Select [Password] on the [Lock] menu and then
press D.
System Setting
4. Press b ENTER and select the second character
using WS buttons.
5. Press b ENTER to confirm your Area code
selection.
Rating
Blocks playback of rated DVDs based on their
contents. Not all discs are rated.
1. Select [Rating] on the [Lock] menu then press D.
2. Input a password and press b ENTER.
3. Select a rating from 1 to 8 using the WS
buttons.
[Rating 1-8]
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
To change the password, press b ENTER when
the [Change] option is highlighted.
Input a password and press b ENTER.
Enter it again and press b ENTER to verify.
4. Press n to exit the menu.
,,Note
If you forget your password, you can clear it
using the following steps :
1. Select the [Setup] menu on the [Home
Menu].
2. Input the 6-digit number “210499” and
press b ENTER. The password is cleared.
Area Code
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list on
page 41.
1. Select [Area Code] on the [Lock] menu then
press D.
2. Input a password and press b ENTER.
3. Select the first character using WS buttons.
[Unlock]
4. Press b ENTER and select the second character
using WS buttons.
If you select unlock, parental control is not active
and the disc plays in full.
5. Press b ENTER to confirm your Area code
selection.
4. Press b ENTER to confirm your rating selection.
Operating 27
Using the Home Menu
1. Press n.
Displays the [Home Menu].
To
Stop
Playback
Pause
Frame-byFrame playback
2. Select an option by using AD.
3. Press b ENTER then selected option menu.
[Music] – Displays [Music] menu.
[Movie] – Start video media’s playback or displays the
[Movie] menu.
[Photo] – Displays [Photo] menu.
Skipping to the
next/ previous
chapter/ track/
file
[Setup] – Displays the [Setup] menu.
,,Note
Basic Operations
1. Insert the disc by using the B or connect the
USB device to the USB port.
Playing
repeatedly or
randomly
2. Press n.
Displays the [Home Menu].
3. Select an option by using AD.
If you select the [Movie], [Photo] or [Music]
option when you connect up to two devices, it
appears as belows. Select a media then press
b ENTER.
4. Press b ENTER then selected option menu.
,,Note
yy For the most Audio CD and DVD-ROM discs,
playback starts automatically.
yy The unit plays only music file contained in the
USB storage device or disc automatically.
Press Z.
Press d MONO/STEREO.
Press M.
Press M repeatedly to play title
Frame-by-Frame. (DVD, Movie
only)
During playback, press
C/V to go to the next
chapter/ track/ file or to return
to the beginning of the current
chapter/ track/ file.
Press C twice briefly to
step back to the previous
chapter/ track/ file.
During playback, press
c/v repeatedly to select
the required scan speed.
To return to normal speed,
press d MONO/STEREO.
Press h REPEAT repeatedly,
and the current title, chapter
or track will be played back
repeatedly or randomly.
- DVD : Chapter/ Title/ Off
- Video(MOVIE) : Title/ All/ Off
- Audio CD/ MP3/ WMA : Track/
All/ Random/ Off
Slowing down
the playing
speed
In the pause mode, press
c/v to select the required
speed. (DVD only)
To return to normal speed,
press d MONO/STEREO.
In the pause mode, press
v to select the required
speed. (Movie only)
To return to normal speed,
press d MONO/STEREO.
4
Operating
You can not select the [Music], [Movie] or
[Photo] option when the USB device is not
connected or a disc is not inserted.
Locating a
point quickly by
playing a file in
fast forward or
fast reverse
Do this
28 Operating
Other Operations
Displaying Disc Information onscreen
You can display various information about the disc
loaded on-screen.
r
The 1.5 speed allows you to watch the pictures and
listen to the sound quicker than playing at a normal
speed.
1. During playback, press d MONO/STEREO to
play at 1.5 times speed. “dX1.5” appears on the
screen.
1. Press m INFO/DISPLAY to show various
playback information.
The displayed items differ depending on the disc
type or playing status.
2. Press d MONO/STEREO again to exit.
2. You can select an item by pressing WS and
change or select the setting by pressing AD.
The screen saver appears when you leave the unit in
Stop mode for about five minutes.
Title – Current title number/ total number of titles.
Chapter – Current chapter number/ total number of
chapters.
Time – Elapsed playing time.
4
1.5 times speed playback
Audio – Selected audio language or channel.
Operating
Subtitle – Selected subtitle.
Angle – S
elected angle/ total number of angles.
,,Note
Screen Saver
Starting play from selected time
ry
To start playing at any chosen time on the file or title.
1. Press m INFO/DISPLAY during playback.
2. Press WS to select the time clock icon and
“--:--:--” appears.
r
3. Input the required start time in hours, minutes,
and seconds from left to right. If you enter the
wrong numbers, press CLEAR to remove the
numbers you entered. Then input the correct
numbers.
For example, to find a scene at 1 hour, 10
minutes, and 20 seconds, enter “11020” by using
numerical buttons.
When you play a DVD which contains several menu,
you can select the menu you want using the Menu.
4. Press b ENTER to confirm. Playback starts from
the selected time.
1. Press DISC MENU.
The disc’s menu appears.
Resume playback
2. Select the menu by using WSAD.
ryut
If any button is not pressed for a few seconds,
the on-screen display disappears.
To display the DVD Menu
3. Press d MONO/STEREO to confirm.
To display the DVD title
r
When you play a DVD which contains several title,
you can select the title you want using the Menu.
1. Press TITLE.
The disc’s title appears.
2. Select the menu by pressing WSAD.
3. Press d MONO/STEREO to confirm.
The unit records the point where you pressed the Z
depending on the disc.
If “MZ (Resume Stop)” appears on the screen briefly,
press d MONO/STEREO to resume playback (from
the scene point).
If you press Z twice or unload the disc,
“Z”(Complete Stop) appears on the screen. The unit
will clear the stopped point.
Operating 29
,,Note
yy The resume point may be cleared when a
button is pressed (for example; 1(POWER),
B, etc).
yy This function may not work on some disc or
title/track.
2. Select a desired music on the [List] by using the
WS then press MARKER to appears the mark
on the list.
3. Press b ENTER.
Displays the play mode.
4. Select the play mode by using the WS and press
b ENTER.
Changing subtitle code page
[Mark Play]
If the subtitle is not displayed properly, you can
change the subtitle code page to view the subtitle file
properly.
[Current Play]
y
1. During playback, press m INFO/DISPLAY to
display the On-Screen display.
2. Use WS to select the [Code Page] option.
Marked playback.
Normal playback.
,,Note
If you want to select all files on the list, select
[Select All] and press b ENTER.
3. Use AD to select desired code option.
To delete a Marker
Marked Playback
1. Use WS to select the track that you wish to
erase from the marked file.
ut
The mark function enables you to store your
favourite files from any disc or USB device in the unit
memory.
1. Select [Music] on the [Home Menu].
Returning to the upper folder.
(MP3/ WMA only)
File information will be displayed
according to the ID3TAG information
on the appropriate music file. (MP3
only)
Selecting all tracks/ files.
Deselecting all tracks/files.
Moving to the previous or next
file list.
2. Press MARKER.
To delete all Markers
Use WSAD to select [Deselect All] then press
b ENTER in program edit mode.
,,Note
The markers are also cleared when the disc or
USB device is removed, the unit is switched to
power off or the function is switched to others.
4
Operating
4. Press x RETURN to exit the On-Screen display.
30 Operating
Viewing a PHOTO file
About help menu in the full screen
Menu
Buttons
Menu
m
INFO/
DISPLAY
Displaying the Option
menu.
a/d
Prev./ Next
A/D
Moving to another file.
i
This unit can play discs with photo files.
1. Select [Photo] on the [Home Menu] and press
b ENTER.
Moving to the previous or next
file list.
x
List
x
RETURN
Operation
Returning to the
[Photo] menu.
Options while viewing a photo
You can use various options during viewing a photo in
full screen.
1. While viewing a photo in full screen, press
m INFO/DISPLAY to display the option menu.
4
2. Select an option using WSAD.
Returning to the upper
folder.
Operating
2. Press WS to select a folder, and then press
b ENTER.
3. If you want to view a slide show, press WS to
highlight a file and press d MONO/STEREO.
a
About help menu in the [Photo] menu
Menu
Buttons
Operation
d Slide
Show
d
MONO/
STEREO
Viewing a slide show.
wsad
Move
WSAD
Moving to another
file or content.
b ENTER
Viewing a particular
file.
b
Select
x
Close
x RETURN
Returning to the
[Home Menu].
b c
de
a Current photo/ Total number of photos –
Use AD to view previous/next photo.
b Slide Show d/M– Press b ENTER to start or
pause slide show.
c Speed x3/ x2/ x1 – Use b ENTER to select a
delaying speed between photos in a slide show.
d Rotate – Press b ENTER to rotate the photo.
e Go to list – Press b ENTER to return [Photo]
menu.
Operating 31
Sleep Timer Setting
Last Scene Memory
Press SLEEP one or more times to select delay time
between 10 and 180 minutes, after the unit will turn
off.
r
To check the remaining time, press SLEEP.
To cancel the sleep function, press SLEEP repeatedly
until “SLEEP 10” appears, and then press SLEEP
once again while “SLEEP 10” is displayed.
Power Resume - Optional
,,Note
You can check the remaining time before the
Unit turns off.
Press SLEEP The remaining time appears in the
display window.
Dimmer
Press SLEEP once. The display window will be darken
by half. To cancel it, press SLEEP repeatedly until dim
off.
to mute your unit.
You can mute your unit in order, for example, to
answer the telephone, appears the MUTE in the
display window.
To cancel it, press again
level.
or change the volume
r
Even if the power suddenly goes out, turn on the
unit and then it plays a position where the contents
is being played. System will periodically save current
playback status.
System Select - Optional
You must select the appropriate system mode for
your TV system. Press and hold M for more than five
seconds to be able to select a system in the [Home
Menu].
,,Note
If the USB device is connected or a disc is
inserted, this function is not operated.
4
Operating
Turn off the sound temporarily
Press
This unit memorizes last scene from the last disc that
is viewed. The last scene remains in memory even if
you remove the disc from the unit or switch off the
unit. If you load a disc that has the scene memorized,
the scene is automatically recalled.
32 Operating
Adjust the speaker level settings
Auto power down
You can adjust the sound level of each speaker.
This unit will be off itself to save electric consumption in
the case main unit is not connected to external device
and is not used for 20 minutes. So does this unit after
six hours since Main unit has been connected to other
device using analog input.
1. Press SPEAKER LEVEL repeatedly to select a
desired speaker to set.
2. Press VOL -/+ to adjust the sound level of the
selected speaker while the level setting menu is
displayed on the display window.
3. Repeat and adjust the sound level of the other
speakers.
VOCAL FADER
You can enjoy the function as karaoke, by reducing
singer vocal of music in the various source. (MP3/
WMA/ CD/ etc.) Press the VOCAL FADER, and
“FADE ON” will appear in display window.
To cancel it, press VOCAL FADER again.
4
The quality of the VOCAL FADER may be different
depending on the recording conditions of music files.
Operating
,,Note
yy This function is available to use only when a
microphone is connected.
yy It is not available on the MONO source.
How to disconnect the wireless
network connection or the wireless
device
Turn off the unit by pressing the power button for more
than 5 seconds.
Operating 33
Radio Operations
Be sure that FM antenna is connected.
(Refer to the page 22.)
Listening to the radio
1. Press P FUNCTION until FM appears in the
display window.
The last received station is tuned in.
2. Press and hold TUNING (-/+) for about two
seconds until the frequency indication starts to
change, then release. Scanning stops when the
unit tunes in a station.
Deleting all the saved stations
1. Press and hold CLEAR for two seconds.
“ERASEALL” will flash up on the unit display.
2. Press CLEAR to erase all saved of the radio
stations.
Deleting a saved station
1. Press PRESET W/S to select a preset number
you want to delete.
2. Press CLEAR, the preset number will blink in the
display window.
3. Press CLEAR again to delete the selected preset
number.
or
Press TUNING (-/+) repeatedly.
3. Adjust the volume by pressing VOL (-/+)
repeatedly.
You can preset 50 stations for FM.
Before tuning, make sure that you have turned down
the volume.
1. Press P FUNCTION until FM appears in the
display window.
2. Select the desired frequency by using
TUNING (-/+).
3. Press b ENTER a preset number will flash in the
display window.
4. Press PRESET (W/S) to select the preset
number you want.
5. Press b ENTER.
The station is stored.
6. Repeat the steps 2 to 5 to store other stations.
7. To listen a preset station, press
PRESET (W/S) or 0 to 9 numerical buttons on
the remote control.
Press d MONO/STEREO on the remote control.
This will change the tuner from stereo to mono and
usually improve the reception.
4
Operating
Presetting the Radio Stations
Improving poor FM reception
34 Operating
,,Note
Sound adjustment
yy In some of surround modes, some speakers,
there’s no sound or low sound. It depends
on the mode of surround and the source of
audio, it is not defective.
Setting the surround mode
This system has a number of pre-set surround sound
fields. You can select a desired sound mode by using
SOUND EFFECT.
You can change the SOUND EFFECT using AD
arrow key while the sound effect information is
displayed on.
The displayed items for the equalizer maybe different
depending on sound sources and effects.
On Display
4
Description
Operating
STANDARD
(STD)
You can enjoy the sound
without equalizer effect.
BASS BLAST
(BASS)
The BASS is Bass Blast. During
playback, reinforce the treble,
bass and surround sound
effect.
USER EQ
FOOTBALL
POWER FRONT
(P-FRONT)
You can adjust the sound
effect.
You can enjoy more dynamic
sound as watching sports
game in the stadium.
You can enjoy the harmonious
sound. This mode is suited
for front-positioned speakers
when they are all placed in a
row.
.
yy This function is not operated when the
microphone is connected to the unit.
Setting the USER EQ
You can adjust the sound level of Bass(BASS) and
Treble(TRE) as your preference.
1. Use SOUND EFFECT to select the USER EQ then
press b ENTER.
2. Use WS to select Bass (BASS) or Treble(TRE).
3. Use AD to select the sound level of Bass(BASS)
or Treble(TRE) then press b ENTER to save the
setting.
Operating 35
Advanced Operations
Recording to USB
You can record music or sound souce to USB device
by connecting in to the port on the unit.
1. Connect the USB device to the unit.
2. Select a mode in which you want to record.
Playback a sound source first.
3. Start the recording by pressing X REC.
4. To stop recording, press Z.
[All tracks/ files recording]
Record to USB in stop or play mode.
[Program list recording]
After marking desired file(s) and you can record
it to USB (Refer to the page 29).
It’ll be stored as follows.
yy You can check the recording percentage rate
for the USB record on the screen during the
recording. (Audio CD or MP3/ WMA CD only)
yy During recording MP3/WMA, there is no
sound.
yy When you stop recording during playback, the
file that has been recorded at that time will
be stored. (Except MP3/WMA files)
yy Do not remove the USB device or turn off
the unit during USB recording. If does not, an
incomplete file may be made and not deleted
on PC.
yy Recording through microphones is not
available.
yy If USB recording does not work, the message
like “NO USB”, “ERROR”, “USB FULL” or “NO
REC” is displayed on the display window.
yy Multi card reader device or external HDD can
not be used for USB recording.
yy A file is recorded by 128 Mbyte (about 2
hours) when you record for a long term. There
are recorded less than 4 files.
yy In the state CD-G, DTS disc USB record is not
operated.
yy The files in the sub-folders are not recorded
during all track recording.
MP3/ WMA
The other
sources (Tuner,
AUX, Portable)
yy You may not record more than 999 files.
yy The numbering of the recording file is entered
from the lowest number. So if you delete
some of the recording files, the next recording
file could be the lowest number among them.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights.
4
Operating
Audio CD
,,Note
36 Operating
Using a Bluetooth
wireless technology
About Bluetooth
Bluetooth is wireless communication technology for
short range connection.
The sound may be interrupted when the connection
interfered by the other electronic wave or you
connect the Bluetooth in the other rooms.
Connecting individual devices under
Bluetooth® wireless technology does not incur any
charges. A mobile phone with Bluetooth wireless
technology can be operated via the Cascade if
the connection was made via Bluetooth wireless
technology.
Available Devices : Mobile phone, MP3, Laptop, PDA
4
Bluetooth Profiles
Operating
In order to use Bluetooth wireless technology,
devices must be able to interpret certain profiles. This
unit is compatible with following profile.
A2DP (Advanced Audio Distribution Profile)
Listening to music of a
Bluetooth device
Pairing your unit and Bluetooth device
Before you start the pairing procedure, make sure the
Bluetooth feature is turned on in to your Bluetooth
device. Refer to your Bluetooth device’s user guide.
Once a pairing operation is performed, it does not
need to be performed again.
1. Select the Bluetooth function by using the
P FUNCTION.
Appears “BT READY” in display window.
2. Operate the Bluetooth device and perform the
pairing operation. When searching for this unit
with the Bluetooth device, a list of the devices
found may appear in the Bluetooth device display
depending on the type of Bluetooth device. Your
unit appears as “LG HTS(XX:XX)”.
,,Note
XX:XX means the last four digits of BT address.
For example, if your unit has a BT address
such as 9C:02:98:4A:F7:08, you will see “LG
HTS(F7:08)” on your Bluetooth device.
3. When this unit is successfully connected with
your Bluetooth device, “PAIRED” appears on the
display window and change to Bluetooth device
name soon.
,,Note
Depending on the Bluetooth device type, some
device have a different pairing way.
4. Listening to music.
To play a music stored on your Bluetooth device,
refer to your Bluetooth device’s user guide.
,,Note
yy If you change the function of the unit, the
Bluetooth function is disconnected, operate
pairing again.
(Bluetooth
Function other than the
Bluetooth)
yy Depending on the Bluetooth device type,
some device have a different pairing way.
(Enter the PIN code (0000) as needed.)
Operating 37
,,Note
yy The sound may be interrupted when the
connection interfered by the other electronic
wave.
yy You cannot control the Bluetooth device with
this unit.
yy Pairing is limited one Bluetooth device per
one unit and multi-pairing is not supported.
yy Depending on the type of the device, you may
not be able to use the Bluetooth function.
yy You can enjoy wireless system using phone,
MP3, Notebook, headset, etc..
yy When not connected the Bluetooth, “BT
READY” appears on the display window.
yy The Electrical malfunction due to devices
using same frequency such as Medical
equipment, Microwaves or wireless LAN
devices, the connection will be disconnected.
yy If the gotten away of the distance between
Bluetooth and the unit, the sound quality
is lower and lower the connection will
disconnect when the space between the
Bluetooth and the unit gets out of the
operating range of Bluetooth.
yy If the function is changed to Bluetooth again
from other function, Bluetooth device is
paired automatically.
yy If the Bluetooth device name contains special
characters, they are displayed as “_” on the
display window.
yy Bluetooth connection are unavailable during
recording.
4
Operating
yy When someone stands and interrupts
communication between Bluetooth device
and the player, the connection will be
disconnected.
38 Operating
Auto function change
AUTO POWER On
This unit recognizes input signals such as Bluetooth
and then changes suitable function automatically.
This unit automatically turns on by an input source :
Bluetooth.
When you try to connect Bluetooth
device
When you turn on your external device connected
to this unit, this unit recognizes the input signal and
select the suitable function. You can hear the sound
from your device.
When you try to connect your Bluetooth device to
this unit, Bluetooth function is selected. Play your
music on the Bluetooth device.
,,Note
yy The Bluetooth unit which is not paired
with this unit, cannot use the auto function
change.
4
yy If you change the this unit’s function to other
function, some Bluetooth unit may try to
connecting in succession. Disconnect the
Bluetooth connection before changing of the
this unit’s function.
If you try to connect your Bluetooth device, this unit
turns on and is paired automatically. And then play
your music.
,,Note
yy After the unit is turned on by AUTO POWER
function, it will be automatically turned off if
there is no signal for a certain period of time
from the external device.
yy Depending on the connected device, this
function may not operate.
Operating
yy If you disconnect Bluetooth connection by
this unit, some Bluetooth devices try to
connect to the unit continually. Therefore it is
recommended to disconnect the connection
before turn off the unit.
yy If you want to use AUTO POWER, SIMPLINK
must be turned off. It takes for about 30
seconds to switch on or off SIMPLINK.
yy If you have already paired with this unit
automatically this unit can turn on by an
input.
yy If you turn off the unit by pressing the power
button for more than 5 seconds, Auto Power
On function is disabled. To activate it, turn on
the unit.
Troubleshooting 39
Troubleshooting
PROBLEM
The unit does not work properly.
CORRECTION
yy Turn off the power of this unit and the connected external device (TV,
Woofer, DVD-player, Amplifier, etc.) and turn it on again.
yy Disconnect the power cord of this unit and the connected external device (TV,
Woofer, DVD-player, Amplifier, etc.) and then try connecting again.
No power
yy Plug the power cord into the wall outlet securely.
No picture
yy Select the appropriate video input mode on the TV so the picture
from the unit appears on the TV screen.
yy Connect the video cables securely to both the TV and unit.
yy Select the correct input mode of the unit so you can hear the sound
from the unit.
There is little or no sound
The DVD picture quality is poor
A DVD/CD will not play
yy Connect the audio cables into the connection terminals correctly.
yy Replace with a new audio cable.
yy Clean the disc using a soft cloth with outward strokes.
yy Insert a disc.
yy Insert a playable disc (check the disc type, colour system and
regional code).
yy Place the disc with the label or printed side facing upwards.
yy Enter your password or change the rating level.
Radio stations can’t be tuned in
properly
yy Check the antenna connection and adjust its position.
yy Attach an external antenna if necessary.
yy Tune to the station manually.
yy Preset some radio stations, see page 33 for details.
yy The remote is not pointed directly at the unit.
Point the remote directly at the unit.
yy The remote is too far from the unit.
Use the remote within 23 feet (7 m) of the unit.
The remote control doesn’t work well
yy There is an obstacle in the path between the remote control and
/ at all
the unit.
Remove the obstacle.
yy The battery in the remote control are flat.
Replace the battery with new ones.
yy Check connection of the external device such as TV, DVD/Blu-Ray
player or Bluetooth device.
The AUTO POWER function does not
yy Check the state of SIMPLINK and turn off SIMPLINK.
work.
yy Depending on the connected device, this function may not operate.
5
Troubleshooting
Humming noise heard while a DVD or yy Clean the disc using a soft cloth with outward strokes.
yy Move unit and audio components further away from your TV.
CD is playing
40 Appendix
Maintenance
Handling the Unit
When shipping the unit
Please save the original shipping carton and packing
materials. If you need to ship the unit, for maximum
protection, re-pack the unit as it was originally
packed at the factory.
Keeping the exterior surfaces clean
yy Do not use volatile liquids such as insecticide spray
near the unit.
yy Wiping with strong pressure may damage the
surface.
yy Do not leave rubber or plastic products in contact
with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not use
strong solvents such as alcohol, benzine, or thinner,
as these might damage the surface of the unit.
Maintaining the Unit
6
Appendix
The unit is a high-tech, precision device. If the optical
pick-up lens and disc drive parts are dirty or worn, the
picture quality could be diminished. For details, please
contact your nearest authorized service center.
Notes on Discs
Handling Discs
Do not touch the playback side of the disc. Hold the
disc by the edges so that fingerprints do not get on
the surface. Never stick paper or tape on the disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center to out.
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
Appendix 41
Area Code List
Choose an area code from this list.
AreaCode AreaCode AreaCode AreaCode
Afghanistan AF Fiji FJ Monaco MC Singapore SG
Argentina AR Finland FI Mongolia MN Slovak Republic SK
Australia AU France FR Morocco MA Slovenia Austria AT Germany DE Nepal NP South Africa ZA
Belgium BE Great Britain GB Netherlands NL South Korea KR
Bhutan BT Greece GR Antilles AN Spain ES
Bolivia BO Greenland GL New Zealand NZ Sri Lanka LK
Brazil BR Hong Kong HK Nigeria NG Sweden SE
Cambodia KH Hungary HU Norway Canada CA India IN Oman Chile CL Indonesia ID Pakistan PK Thailand China CN Israel IL Panama PA Turkey TR
Colombia CO Italy IT Paraguay PY Uganda UG
Congo CG Jamaica JM Philippines PH Ukraine UA
Costa Rica CR Japan JP Poland PL United States US
Croatia HR Kenya KE Portugal PT Uruguay UY
Czech Republic CZ Kuwait KW Romania Denmark DK Libya Ecuador EC Luxembourg LY Russian
LU Federation EG Malaysia El Salvador SV Maldives Ethiopia ET Mexico MX
NO Switzerland CH
OM Taiwan TW
RO Uzbekistan Vietnam RU Zimbabwe SA
SN
TH
UZ
VN
ZW
6
Appendix
Egypt MY Saudi Arabia MV Senegal SI
42 Appendix
Language code List
Use this list to input your desired language for the following initial settings: [Disc Audio],
[Disc Subtitle] and [Disc Menu].
6
Appendix
LanguageCode
LanguageCode
LanguageCode
LanguageCode
Afar 6565
French 7082
Lithuanian 7684
Sindhi 8368
Afrikaans 6570
Frisian 7089
Macedonian 7775
Singhalese 8373
Albanian 8381
Galician 7176
Malagasy 7771
Slovak 8375
Ameharic 6577
Georgian 7565
Malay 7783
Slovenian 8376
Arabic 6582
German 6869
Malayalam 7776
Spanish 6983
Armenian 7289
Greek 6976
Maori 7773
Sudanese 8385
Assamese 6583
Greenlandic 7576
Marathi 7782
Swahili 8387
Aymara 6588
Guarani 7178
Moldavian 7779
Swedish 8386
Azerbaijani 6590
Gujarati 7185
Mongolian 7778
Tagalog 8476
Bashkir 6665
Hausa 7265
Nauru
7865
Tajik 8471
Basque 6985
Hebrew 7387
Nepali 7869
Tamil 8465
Bengali; Bangla 6678
Hindi 7273
Norwegian 7879
Telugu 8469
Bhutani 6890
Hungarian 7285
Oriya 7982
Thai 8472
Bihari 6672
Icelandic 7383
Panjabi 8065
Tonga 8479
Breton 6682
Indonesian 7378
Pashto, Pushto 8083
Turkish 8482
Bulgarian 6671
Interlingua 7365
Persian 7065
Turkmen 8475
Burmese 7789
Irish 7165
Polish 8076
Twi 8487
Byelorussian 6669
Italian 7384
Portuguese 8084
Ukrainian 8575
Chinese 9072
Japanese 7465
Quechua 8185
Urdu 8582
Croatian 7282
Kannada 7578
Rhaeto-Romance 8277
Uzbek 8590
Czech 6783
Kashmiri 7583
Rumanian 8279
Vietnamese 8673
Danish 6865
Kazakh 7575
Russian 8285
Volapük 8679
Dutch 7876
Kirghiz 7589
Samoan 8377
Welsh 6789
English 6978
Korean 7579
Sanskrit 8365
Wolof 8779
Esperanto 6979
Kurdish 7585
Scots Gaelic 7168
Xhosa 8872
Estonian 6984
Laothian 7679
Serbian 8382
Yiddish 7473
Faroese 7079
Latin 7665
Serbo-Croatian 8372
Yoruba 8979
Fiji 7074
Latvian, Lettish 7686
Shona 8378
Zulu 9085
Finnish 7073
Lingala 7678
Appendix 43
Trademarks and
Licenses
All other trademarks are trademarks of their
respective owners.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
Notes on Copyrights
yy This product incorporates copyright protection
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Rovi, and is intended for home and
other limited viewing uses only unless otherwise
authorized by Rovi. Reverse engineering or
disassembly is prohibited.
yy Under the U.S. Copyright laws and Copyright
laws of other countries, unauthorized recording,
use, display, distribution, or revision of television
programs, videotapes, BD-ROM discs, DVDs, CDs
and other materials may subject you to civil and/or
criminal liability.
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
Other trademarks and trade names are those of
their respective owners.
6
Appendix
The Bluetooth® word mark and logos are owned
by the Bluetooth® SIG, Inc. and any use of such
marks by LG Electronics is under license.
44 Appendix
Specifications
General
Power requirements
Refer to main label.
Refer to main label.
Power consumption
Networked standby 0.5 W (If all network ports are activated.)
Dimensions (W x H x D)
Approx. (360 x 58 x 298.5) mm without foot
Net Weight (Approx.)
Approx. 2.46 kg
Operating temperature
5 °C to 35 °C
Operating humidity
5 % to 90 %
Bus Power Supply
5 V 0 500 mA
Inputs/ Outputs
VIDEO OUT
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
HDMI OUT (video/audio)
19 pin (Type A, HDMI™ Connector) x 1
ANALOG AUDIO IN
2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
DIGITAL IN (OPTICAL)
3 V (p-p), Optical jack x 1
PORT. IN
0.5 Vrms (3.5 mm stereo jack) x 1
Amplifier
Stereo mode
6
Surround mode
167 W + 167 W (3 Ω at 1kHz)
Appendix
Front
167 W + 167 W (3 Ω at 1 kHz)
Center
167 W (3 Ω at 1 kHz)
Surround
167 W + 167 W (3 Ω at 1 kHz)
Subwoofer
167 W (3 Ω at 60 Hz)
Tuner
FM Tuning Range
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
Appendix 45
Front Speaker
Type
1 way 1 speaker
Impedance
3Ω
Rated Input Power
167 W
Max. Input Power
334 W
Net Dimensions (W x H x D)
Approx. (250 x 1150 x 250) mm
Net Weight
Approx. 3.7 kg
Rear Speaker
Type
1 way 1 speaker
Impedance
3Ω
Rated Input Power
167 W
Max. Input Power
334 W
Net Dimensions (W x H x D)
Approx. (250 x 1150 x 250) mm
Net Weight
Approx. 3.7 kg
Center Speaker
Type
1 way 1 speaker
Impedance
3Ω
Rated Input Power
167 W
Max. Input Power
334 W
Net Dimensions (W x H x D)
Approx. (260 x 93 x 73) mm
Net Weight
Approx. 0.65 kg
6
Passive Subwoofer
1 Way 1 Speaker
Impedance
3Ω
Rated Input Power
167 W
Max. Input Power
334 W
Net Dimensions (W x H x D)
Approx. (191 x 386 x 318) mm
Net Weight
Approx. 5.2 kg
yy Design and specifications are subject to change without notice.
Appendix
Type
Download PDF