LG | NP3530 | LG NP3530 Owner’s Manual

Charging
Product Overview
Bluetooth Connection
App Installation
Wired Connection
To use this unit more comfortably, install “LG Bluetooth Remote” on
your bluetooth devices. Select a way of installation ( , or ).
Wireless Speaker
NFC for Easy Pairing: You can pair simply and easily by
ON tapping your smartphone on to the NFC sticker.
NP3530
Press and hold to turn on the unit.
Searching for “LG Bluetooth Remote” on the
Google Play Store.
Approx. 3 hours
Note
Operating time is approx. 15 hours. (Based on 30% volume, 1 kHz
signal, 500 mV portable input and fully charged status)
It may vary depending on the battery status and operational
conditions.
Within 10 m
Scanning QR code below.
Press and hold to turn on or off.
ENGLISH OWNER’S MANUAL
Please read this manual carefully before operating your set and retain it
for future reference.
Select “LG Portable(XX:XX)” on your Bluetooth device.
(XX:XX means the last four digits of BT address.)
yy Depending on the bluetooth device, you need to enter the PIN code (0000).
yy Once a pairing operation is performed, it does not need to be performed
again every time you turn on the unit. (Only if the PORT.IN is not connected
and the unit is registered on the Bulutooth device.)
Tagging on the NFC sticker, if available.
Note: When bluetooth device is connected without BT remote
App, PORT. IN connection does NOT work.
Press and hold to disconnect.
http://www.lg.com
Safety Information
About LED Indicator
Using handsfree function
Additional Information
About Ferrite Core (Optional)
LG Bluetooth Remote
Preparation: Your smartphone must be paired with the unit via bluetooth.
Turned on red
Turned on white
Turned off
Beep sound
Scan to install the App.
Press to hang up the call.
In Charging
Fully Charged (Power Off mode)
Resetting
X2
In Charging
Fully Charged (Power On mode)
X2
X2
Power is turned on.
X2
Bluetooth is paired.
X2
X2
X2
5 V 0 2.0 A
Battery is discharged. (Blinks rapidly.)
X2
Press to accept an incoming call.
X2
X2
X2
Reset hole
In case that the unit freezes due to malfunction, press the reset
hole for 5 seconds using an object like a thin pin.
Notice for Auto Power Off
This unit is turned off automatically, if no button is pressed for 6
hours when the bluetooth is disconnected.
How to attach the ferrite core
This ferrite core can reduce noises.
1. Pull the stopper [a] of the ferrite core to open.
2. Wind the portable cable and USB cable on the ferrite core.
3. Close the ferrite core until it clicks.
A button is pressed.
The unit operates abnormally. Leave the unit at room temperature (0 - 35 °C) for a while and try again.
X2
X2
X2
Press and hold to toggle the voice output.
Press and hold to reject an incoming call.
NP3530-B0_BSGPLLK_OM_MFL67786208_20130322.indd 1
2013-03-25 �� 2:08:57
Specification
Troubleshooting
Safety Information
Power Supply:
-- 5 V 0 2.0 A (AC Adapter)
-- Built-in rechargeable battery
No power
yy The battery is discharged. Recharge the battery.
yy Connect the unit to the power supply with the AC adapter
AC Adaptor:
-- Model: WB-10A05FG
-- Manufacturer: Yang Ming Industrial
-- Input: AC100-240 V, 50/60 Hz
-- Output: 5 V 0 2.0 A
WARNING:
yy To prevent fire or electric shock hazard, do not expose this product to rain or
moisture.
yy Do not install this equipment in a confined space such as a book case or similar
unit.
No sound or sound distortion
yy The unit or your smart device’s volume is set to minimum. Check and adjust the
volume of the unit or bluetooth device’s volume.
yy When you use an external device at high volume, the sound quality may be
deteriorated. Lower the volume of the devices.
yy If you use the unit for purposes other than listening to music, the sound quality may
be lowered or the unit may not work properly.
Dimensions (W x H x D):
-- Approx. 193 mm x 65 mm x 65 mm
Net Weight:
-- Approx. 520 g
Operating Temperature:
-- 0 °C to 35 °C
Operating Humidity:
-- 5 % to 60 %
External Connector:
-- ø 3.5 mm mini jack
-- Micro USB port for charging battery
Communication:
-- Bluetooth 3.0
Amplifier:
-- 3 W + 3 W (8 Ω at 1 kHz)
-- THD: 10%
Speaker:
-- Type : Built-in
-- Impedance Rate : 8 Ω
-- Rated Input Power : 3 W
-- Max. Input Power : 6 W
Android O/S for App installation:
Version 2.3.3 (or higher)
yy Design and specifications are subject to change without notice.
Bluetooth pairing does not work well.
yy Switch bluetooth off and on again on your bluetooth device, then try pairing again.
yy Be sure your bluetooth device is on.
yy Remove the obstacle in the path of the bluetooth device and the unit.
yy Depending on the type of the bluetooth device or surrounding environment, your
device may not be paired with the unit.
yy While using Bluetooth, you may not be able to activate BT app. Disconnect
Bluetooth device you have connected before to use BT app properly.
yy When your Bluetooth device have been already connected with other unit,
disconnect the Bluetooth connection first. Then you can control your unit through
BT app.
yy Depending on the Bluetooth device, BT app may work restrictively not work.
y
y The connection you’ve made may be disconnected if you select other application
or change the setting of the connected device via BT app. In such case, please
check the connection status.
The unit does not operate normally.
yy In case of malfunction, LED indicator is lit in red and white alternately. Please use
the unit in proper place where the temperature or humidity is not so high or low.
CAUTION:
yy The apparatus should not be exposed to water (dripping or splashing) and no
objects filled with liquids, such as vases, should be placed on the apparatus.
yy No naked flame sources, such as lighted candles, should be placed on the
apparatus.
yy Internal lithium battery in the unit should not be replaced by user because of
danger of explosion if battery is incorrectly replaced ,and must be replaced with the
same type battery by expert.
yy Only use the AC adaptor supplied with this device. Do not use a power supply from
another device or another manufacturer. Using any other power cable or power
supply may cause damage to the device and void your warranty.
yy To avoid fire or electric shock, do not open the unit. contact to qualified personnel
only.
yy Do not leave the unit in a place near the heating appliances or subject to direct
sunlight, moisture, or mechanical shock.
yy To clean the unit, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft
cloth lightly moistened with a mild detergent solution. Do not use strong solvents
such as alcohol, benzine, or thinner, as these might damage the surface of the unit.
yy Do not use volatile liquids such as insecticide spray near the unit.Wiping with
strong pressure may damage the surface. Do not leave rubber or plastic products in
contact with the unit for a long period of time.
yy Do not place the unit over the vehicle’s air bag. When the air bag deploys, it may
result in injury. Before using in the car, fix the unit.
yy Do not use the handsfree function during driving a car.
yy Do not leave the unit on an unstable place such as high shelves. it may fall down
because of the vibration of the sound.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit;
That is, a single outlet circuit which powers only that appliance and has no additional
outlets or branch circuits. Check the specification page of this owner’s manual to be
certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall
outlets, extension cords, frayed power cords, or damaged or cracked wire insulation
are dangerous. Any of these conditions could result in electric shock or fire. Periodically
examine the cord of your appliance, and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized service centre. Protect the power cord
from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in
a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point
where the cord exits the appliance. To disconnect power from the mains, pull out the
mains cord plug. When installing the product, ensure that the plug is easily accessible.
This device is equipped with a portable battery or accumulator.
Safety way to remove the battery or the battery from the equipment: Remove
the old battery or battery pack, follow the steps in reverse order than the assembly.
To prevent contamination of the environment and bring on possible threat to human
and animal health, the old battery or the battery put it in the appropriate container at
designated collection points. Do not dispose of batteries or battery together with other
waste. It is recommended that you use local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to excessive heat such as sunshine, fire
or the like.
NOTICE: For safety making information including product identification and supply
ratings, please refer to the main label on the bottom of the apparatus.
NP3530-B0_BSGPLLK_OM_MFL67786208_20130322.indd 2
2013-03-25 �� 2:08:57
Download PDF

advertising