LG LS-C306MMB0 Owner's Manual

LG
LG
Room Air Conditioner
OWNER'S MANUAL
Prior to
installation, this air-conditioning
unit must be submitted for
approval by the
utility service which provides electricity
(EN 61000-2, EN 61000-3 Norm).
IMPORTANT
?
?
Please read this owner's manual
and
before
air conditioner.
installing
and
carefully
operating your room
thoroughly
Please retain this owner's manual for future reference after
reading it thoroughly.
P/No.: 3828A20397J
Room Air Conditioner Owner's Manual
TABLE OF CONTENTS
FOR YOUR RECORDS
Write the model and serial numbers here:
Model #
Serial #
You
can
find them
on a
label
on
the side of each unit.
Dealer's Name
Date Purchased
Staple
your
receipt to this page in the event you need
purchase or for warranty issues.
it
to prove date of
READ THIS MANUAL
Safety
Precautions .................3
Prior to
Operation
Operating
..................6
Instructions...........7
Remote Controller ..............7
Remote Control
Operation.8
Additional features...............17
Maintenance and Service ....20
Indoor unit.........................20
Inside you will find many helpful hints on how to use and
maintain your air conditioner properly. Just a little
preventive
PRECAUTION
?
?
?
?
?
Room Air Conditioner
you may not need to call for
service at all.
Operation Tips ..................22
2
part can save you a great deal
the life of your air conditioner.
Troubleshooting Tips first,
Outdoor unit ......................21
..............23
your
over
You'll find many answers to common problems in the
chart of troubleshooting tips. If you review our chart of
?
Troubleshooting
care on
of time and money
Contact the authorized service technician for
maintenance of this unit.
repair
or
Contact the installer for installation of this unit.
The air conditioner is not intended for use
children or invalids without supervision.
Young children should be supervised to
they do not play with the air conditioner.
by
young
ensure
that
When the power cord is to be replaced, replacement
work shall be performed by authorized personnel only
using only genuine replacement parts.
Installation work must be performed in accordance
with the National Electric Code by qualified and
authorized personnel only.
Precautions
Safety
Safety
To
to the
prevent injury
Precautions
user or
other
people
and
property damage, the following instructions
must be followed.
Incorrect
classified
operation due to ignoring instruction
by the following indications.
WARNING
This
symbol
CAUTION
This
symbol
Meanings
of
symbols
will
indicates the
indicates the
used in this manual
Be
sure
possibility
possibility
are as
Be
harm
cause
of
or
The seriousness is
damage.
of death
serious
or
injury.
injury or damage to properties only.
shown below.
sure
not to do.
to follow the instruction.
WARNING
Installation
in the power
Plug
Do not
plug properly.
damage
or use an
unspecified
power
cord.
?
Otherwise, it will
heat
generation
cause
or
electric shock
or
fire due to
electric shock.
?
It will
?
In the
cause
electric shock
supply
cord is
the manufacturer
quallfied person
Attachment)
Do not modify power cord length
outlet with other appliances.
?
It will
cause
electric shock
or
or
share the
fire due to heat
or
or
fire.
damaged,
it mut be
its service
agent
in order to avoid
Always perform grounding
?
No
grounding
may
cause
a
replaced by
similarly
hazard. (Y
or a
work.
electric shock.
generation.
Always
install air
dedicated
?
leakage breaker
switching board.
No installation may
cause
and
Do not
a
fire and electric shock
use
the socket if it is loose
or
damaged.
?
It may
cause
fire and electric shock.
accident.
Keep firearms
?
It may
cause
away.
fire.
Owner's Manual
3
Safety
Precautions
Operation
?
Do not
operate
pulling
out the power
It will
cause
or
stop the unit by inserting
Do not allow water to
or
run
into electric parts.
plug.
electric shock
or
fire due to heat
?
It may
cause
failure of machine
or
electric shock.
generation.
Do not
operate with
wet hands
or
in
Do not direct airflow at
damp
room
occupants only.
environment.
?
It may
cause
?
It may
cause
Do not
It may
use
fire and electric shock accident.
?
the power cord close to the
cause
cause
It may
cause
Do not
your health.
during operation.
use
electric shock.
the power cord
combustibles, such
benzene, thinner, etc.
tools.
gas
fire and electric shock.
Ventilate before
It may
damage
Do not open the entrance
or
operating
?
air conditioner
or
It may
cause an
explosion
Do not disassemble
when gas goes out.
?
This could
comes
heating
?
?
the unit if strange sounds, smell,
from it.
Unplug
smoke
electric shock.
or
or
near
as
flammable
gasoline,
fire.
modify products
randomly.
explosion,
fire
and, burn.
?
It may
cause
failure and electric shock.
CAUTION
Installation
Ensure that
use
?
for
an
installation console of the
appliance is
a long time.
outdoor
not
damaged
If leaving appliance damaged, there is
damage due to the falling of product.
4
Room Air Conditioner
Use caution when
due to the
concern
of
Sharp edges
unpacking and installing.
cause injury.
could
Safety
Precautions
Operation
Never touch the metal
removing
?
They
are
parts of the unit when
Do not clean the air conditioner with water.
the filter.
sharp
and may
injury.
cause
Ventilate well when used
?
together with
When
a
An oxygen
shortage
may
?
occur.
Do not
put
a
pet or house plant where it will be
cause
Do not
exposed to direct air flow.
are
as
the insulation. It
turned off.
Since the fan rotates at
may
degrade
cleaning the unit, first make sure the power and
breaker
stove, etc.
?
Water may enter the unit and
may cause an electric shock.
high speed during operation,
it
injury.
use
animals
appliance for special purpose such
vegetables, precision machine, or
or
conservation of art articles.
?
This could
injure
the
pet
or
plant.
?
It may
of
Stop operation
or
?
and close the window in storm
when
with windows
indoor and
soaking
opened may cause
of household furniture.
wetting
of
?
Turn off the main power switch when not
using it for a long time.
?
It may
failure of
cause
Always
product
insert the filters
or
fire.
securely.
Clean it
Operation
Do not
?
cause
or
It may
use
thinner but
without filters may
cause
failure.
?
care so
the power cord
that the cord should not be
or
vegetables
or
loss
head of the power
electric shock and
plug
damage.
place obstacles around the absorption
instead of blowing-out inlet.
cause
Do not
once
of animals
plug by the
taking it out.
Do not
failure of
appliance
or
accident.
strong detergent such
use a
as wax or
soft cloth.
Appearance may be deteriorated due to change
product color or scratching of its surface.
of
Do not drink water drained from air
place heavy object on
and take
It may
inlet
every two weeks.
?
damage
Hold the
hurricane.
Operation
cause
property.
conditioner.
pressed.
?
There is
danger of fire
or
electric shock.
?
It contains contaminants and will make you sick.
If water enters the
product, turn the power
body of appliance off.
power-plug out from the
switch of the main
After
taking
socket,
the
contact with the service center.
Owner's Manual
5
Prior to
operation
Prior to
for
Preparing
1. Contact
2.
in the power
Plug
3. Use
installation
an
operation
operation
specialist
for installation.
plug properly.
dedicated circuit.
a
4. Do not
use an
5. Do not
start/stop operation by plugging/unplugging
6. If the
extension cord.
cord/plug
is
damaged, replace
it with
only
an
the power cord.
authorized
replacement part.
Usage
1.
Being exposed
to direct airflow for
an
Do not expose
occupants, pets,
plants
2. Due to the
other
possibility of
heating devices.
3. Do not
use
oxygen
or
extended
period
of time could be hazardous to your health.
periods of time.
to direct airflow for extended
deficiency,
ventilate the
room
when used
together with
stoves
or
this air conditioner for
food, pets, plants, and
art
non-specified special purposes (e.g. preserving precision devices,
objects). Such usage could damage the items.
Cleaning and maintenance
1. Do not touch the metal
sharp
metal
2. Do not
leading
use
to
parts of the unit when removing the filter. Injuries
water to clean inside the air conditioner.
possible
when
handling
Exposure
to water
can
destroy the insulation,
electric shock.
3. When
cleaning the unit, first make sure that the power and breaker are
high speed during operation. There is a possibility of injury if the
triggered on while cleaning inner parts of the unit.
a
can occur
edges.
very
turned off. The fan rotates at
unit's power is
accidentally
Service
For
repair
and maintenance, contact your authorized service dealer.
Symbols
Used in this Manual
This
symbol
alerts you to the risk of electric shock.
This
symbol
alerts you to hazards that could
air conditioner.
NOTICE
6
This
symbol
Room Air Conditioner
indicates
special
notes.
cause
harm to the
Operating
Instructions
Instructions
Operating
Remote Controller
1. Remove the
battery
2. Insert
new
battery
batteries
NOTICE
use
it
according
to the
cover
that the
it back into
by sliding
(+)
and
(-)
of
position.
Use 2 AAA(1.5volt) batteries.
rechargeable batteries.
and
Storage
?
by pulling
making sure
correctly.
installed
are
3. Reattach the
Do not
cover
direction.
arrow
For
Tips
the Remote Control
Using
The remote control may be stored mounted
on a
wall.
?
To
operate the
control at the
room
air
conditioner, aim the
remote
signal receptor.
Signal Receptor
Receives the
signals
from the remote
Indication
Operation
On/Off
Timer
or
:
Sleep
Mode
Defrost Mode
:
:
control.(Signal receiving
sound: two short
beeps
or one
long beep.)
Lamps
Lights
Lights
up
up
during
the
during
Timer
system operation.
operation
or
Sleep
mode.
Lights up during Defrost Mode or Hot
operation (Heat pump model only)
Start
:
Lights up during outdoor
(Cooling model only)
Plasma Mode
:
Lights up during plasma-purification operation.
(option)
Auto Restart Mode
:
Lights
Auto Restart Button
:
Outdoor unit
operation
up
during
unit
operation.
if Restart Button is
Signal
pressed. receptor
In failure of electric power, if the button is
Operation
indication
lamps
pressed the unit runs as previous setting
operation when power returns.
Forced
Operation
Button
:
Operation starts,
and
when this button is
pressed
stops when you press the button again.
Owner's Manual
7
Operating
Instructions
Remote Control
The remote control transmits the
Operation
signals
to the
system.
1. START/STOP BUTTON
Operation starts when this button is
pressed and stops when the button is
pressed again.
Signal
2. OPERATION MODE SELECTION
BUTTON
Used to select the operation mode.
transmitter
3. ROOM TEMPERATURE SETTING
BUTTONS
Used to select the room temperature.
4. INDOOR FAN SPEED SELECTOR
Used to select fan speed in four steps
low, medium, high and CHAOS.
5. JET COOL
Used to start
or stop the speed
cooling. (Speed cooling operates
fan
super high
speed in cooling mode.)
1
56
6. CHAOS SWING BUTTON
Used to stop or start louver movement and
set the desired up/down airflow direction.
3
7. ON/OFF TIMER BUTTONS
Used to set the time of starting and
427
stopping operation. (See
10
CANCEL
ON
9
SET
OFF
17
AUTO CLEAN
11
8
14
15
16
17)
17)
9. TIMER SET/CANCEL BUTTON
Used to set the timer when the desired time
is obtained and to cancel the Timer
12
13
page
8. TIME SETTING BUTTONS
Used to adjust the time. (See page
operation. (See page 17)
10. SLEEP MODE AUTO BUTTON
Used to set Sleep Mode Auto operation.
(See page 17)
11. AIR CIRCULATION BUTTON
Used to circulate the room air without
cooling
Flip-up door
(opened)
Operation
13.
Mode
Operation
or
Auto
Changeover
), Heat Pump Model(
PLASMA(OPTIONAL)
15. RESET BUTTON
Used prior to resetting time
replacing batteries.
)
or
Room Air Conditioner
after
16. 2nd F Button
Used prior to using modes printed in blue
at the bottom of buttons. (See page 16)
17. AUTO CLEAN(OPTIONAL)
Used to set Auto Clean mode.
8
18)
14. HORIZONTAL AIRFLOW DIRECTION
CONTROL BUTTON
(NOT ON ALL MODELS)
Used to set the desired horizontal airflow
direction. (See page 18)
Heating Operation
Cooling Model(
page
Used to start or stop the plasmafunction. (See page 15)
Healthy Dehumidification Operation
?
heating. (See
purification
Cooling Operation
Auto
or
12. ROOM TEMPERATURE CHECKING
BUTTON
Used to check the room temperature.
Operating
Instructions
Cooling Operation
1
Press the
a
2
Start/Stop button.
respond with
The unit will
beep.
Open the door on the remote control. To select Cooling
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shiftedinthedirectionofthearrow.
Auto
Cooling
3
Close the door
on
lower than the
room
set within
a
Healthy
Dehumidification
Heating
(Heat pump model only)
the remote control. Set the
temperature
temperature. The temperature can be
range of 18°C~30°Cin1°Cincrements.
ON
To raise the temperature
To lower the temperature
4
Set the fan
speed again
with the door
of the remote control still closed. You
can
select the fan
speed
in four
steps-
low, medium, high and CHAOS.
Each time the button is pressed,
fanspeedmodeisshifted.
Natural wind by the CHAOS
For
more
fresh
feeling
CHAOS mode. In this
speed according
the
logic
than other fan
speed,
press the Indoor Fan
Speed
Selector and set to
mode, the wind blows like natural breeze by automatically changing fan
to the CHAOS
logic.
Owner's Manual
9
Operating
Instructions
Auto
Operation(Optional)
Press the
1
Start/Stop button.
respond with
The unit will
a
2
beep.
Open the door on the remote control. To select Auto
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shiftedinthedirectionofthearrow.
Auto
Cooling
3
ON
The
Healthy
Dehumidification
temperature and fan speed
electronic controls based
on
Heating
(Heat pump model only)
automatically
are
the actual
room
set
by
the
temperature. If
change the set temperature, press the Room
Temperature Setting buttons. The cooler or warmer you feel,
the more times (up to two times) you should press the button.
The set temperature will be changed automatically.
you want to
To raise the temperature
To lower the temperature
During Auto Operation:
You cannot switch the indoor fan
If the
system is
not
operating
It has
already
been set
desired, manually switch
by
the
Fuzzy
rule.
to another mode. The
system will
not
cooling mode to the heating mode, or from heating mode to cooling
mode, it must be done by manually resetting.
During Auto Operation, pressing the chaos swing button makes the horizontal louvers swing up and
down automatically. If you want to stop auto-swing, press the chaos swing button again.
automatically
10
switch from the
speed.
as
Room Air Conditioner
Safety
Auto
Precautions
Changeover Operation(Optional)
1
Press the
a
2
Start/Stop button.
respond with
The unit will
beep.
Open the door on the remote control. To select Auto Changeover
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is shifted in the
direction of the
arrow.
Auto
Cooling
3
Close the door
lower than the
set within
a
changeover
on
Healthy
Dehumidification
Heating
(Heat pump model only)
the remote control. Set the
room
temperature
temperature. The temperature can be
range of 18°C~30°Cin1°Cincrements.
ON
To raise the temperature
To lower the temperature
4
Set the fan
with the door
speed again
of the remote control still closed. You
can
select the fan
speed
in four
steps-
low, medium, high and CHAOS.
Each time the button is
fan
speed
pressed,
the
mode is shifted.
During Auto changeover Operation:
The air conditioner
changes the operation mode automatically to keep indoor temperature. When
temperature vary over ±2°C with respect to setting temperature, air conditioner keeps the
temperature in ±2°C with respect to setting temperature by auto changeover mode.
room
room
Owner's Manual
11
Operating
Instructions
Healthy
Dehumidification
Operation
Press the
1
Start/Stop button.
respond with
The unit will
a
2
beep.
Open
the door
the remote control. To select
on
Dehumidification
Operation,
press the
Healthy
Operation Mode
Selection button.
Each time the button is
pressed,
the
operation
mode is
shiftedinthedirectionofthearrow.
Auto
Cooling
3
Set the fan
with the door
select the fan
speed
in four
or
time the button is
pressed,
Natural wind
the fan
mode is shifted.
by the
fresh
CHAOS
logic
speed, press the Indoor Fan
Selector and set to CHAOS mode. In this mode, the wind
more
Speed
steps-
CHAOS. Each
low, medium, high,
speed
For
speed again
Heating
(Heat pump model only)
of the remote control still closed. You
can
ON
Healthy
Dehumidification
feeling
than other fan
blows like natural breeze
according
to the CHAOS
by automatically changing
logic.
fan
speed
During Healthy Dehumidification Operation:
If you select the dehumidification mode on the operation selection button, the A/C starts to run the
dehumidification function. It automatically sets the room temp. and airflow volume to the best condition
for
dehumidification, based
on
In this case, however, the setting
control the room temp. either.
the sensed current
temp. is
not
room
displayed
temp.
in the remote control and you
are
not able to
During the healthy dehumidification function, the airflow volume is automatically set according to the
optimization algorithm responding to the current room temp. status which makes the room condition
healthy and comfortable even in the high humidity season.
12
Room Air Conditioner
Operating
Heating Operation(Heat pump
1
Press the
Start/Stop button.
respond with
beep.
Open the door on the remote control. To select Heating
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the
Close the door
Set the
arrow.
Auto
Cooling
3
only)
The unit will
a
2
model
Instructions
Healthy
Dehumidification
on
Heating
(Heat pump model only)
the remote control.
temperature higher than the
room
temperature.
Thetemperaturecanbesetwithinarangeof16°C~30°Cin
1°C increments.
ON
To raise the temperature
To lower the temperature
4
Set the fan
speed again
with the door of the
remote control still closed. You
the fan
speed
in four
select
can
steps--low, medium,
high and CHAOS. Each time the button
pressed, the fan speed mode is shifted.
Natural wind by the CHAOS
For
more
fresh
feeling
CHAOS mode. In this
speed according
is
logic
than other fan
speed,
press the Indoor Fan
Speed
Selector and set to
mode, the wind blows like natural breeze by automatically changing fan
to the CHAOS
logic.
Owner's Manual
13
Operating
Instructions
Jet Cool
Operation
1
Press the
a
2
beep.
Press the Jet Cool button to
the
will
on
3
Start/Stop button.
respond with
The unit will
speed cooling
operate
mode and the unit
operate in super high fan speed
cooling
mode for 30 minutes.
To cancel the Jet Cool
mode, press the Jet Cool button or
room temperature setting button
again and the unit will operate in high fan speed on cooling
the fan
speed
button
or
the
mode.
or
or
NOTICE
During the JET COOL function at any moment, the A/C starts to blow the cool air at
extremely high speed for 30 minutes setting the room temp. automatically to 18°C. It is
especially used to cool the room temp. in the shortest time in a hot summer.
In heat pump mode
or neuro
fuzzy mode, however,
In order to return to the normal
either the
or
14
operation
the JET COOL button
Room Air Conditioner
again.
mode from the JET COOL mode, you just press
button, airflow volume selection or temp. setting button
cooling
mode selection
the JET COOL function is not available.
Instructions
Operating
PLASMA Purification
1
Operation(Optional)
Press the
Start/Stop button.
respond with a
The unit will
beep.
2
3
Open
the door
on
the remote control.
Press the PLASMA air
purifying
operation ON/OFF button.
Operation will start when the button is
pressed and stop when the button is
pressed again.
Set the fan
speed again
closed. You
with door of the remote control
speed in four
steps-low, medium, high or CHAOS.
Each time the button is pressed, the fan
speed mode is shifted.
can
select the fan
Air
purifying operation (PLASMA) can be
cooling, Heating or any other operations.
PLASMA Air
with
Purifying Operation only
If you press the only PLASMA button,
PLASMA air purifying operates.
only
Then, fan speed is low. You can select the fan
speed in four steps-low, medium, high or
CHAOS.
Each time the button
speed
(
)
is
pressed,
the fan
mode is shifted.
Owner's Manual
15
Instructions
Operating
2nd F
Operation
1
Press the
a
2
Start/Stop button.
respond with
The unit will
beep.
Open
the door of the remote control and press the 2nd
operate functions printed in blue at bottom
Function button to
of buttons.
(Check the
display.)
indication of 2nd function
These buttons
remote control
on
operate the timer setting
as
follows:
CANCEL
ON
OFF
SET
CANCEL
ON
SET
OFF
AUTO CLEAN
3
2nd function goes off in
the button is
a
short time
automatically
or
when
pressed again.
For more details, refer to functions next page.
Auto
-Clean(Optional)
AUTO CLEAN
1. Whenever you press the Auto Clean button, Auto Clean Function will be reserved and cancelled.
2. Auto Clean function works before and after cooling or dehumidification mode. For details, refer to
the below
points.
3. When the unit is started after the reservation of Auto Clean
,the Cool Start function operates and
indoor Fan is started after 20 seconds.
4. When you press Start/Stop button to turn off the unit after the you have reserved Auto Clean
function, the air-conditioner circulates the indoor air in the Auto Clean mode with no more Cooling
Dehumidification
operation.
Cooling only model, it lasts for 30 minutes for Heat pump model, for 16 minutes.
If you press the auto clean button again during the product operation Auto Clean function
or
For
5.
,
will be
cancelled.
NOTICE
This function is to
to
16
remove
remove unpleasant smells from mold and other bacteria in the air-conditioner, and
humidity automatically during humidly summer, which supplies the indoor with purified air.
Room Air Conditioner
Operating
Instructions
Additional features
Mode
Sleep
1. Press the
Sleep Mode Auto button
timeyouwanttheunittoturnoff
automatically.
To cancel the
Sleep Mode, press the sleep
Mode Auto button several times until the star
to set the
(
programmed in one-hour
by pressing the Sleep Mode
NOTICE
operated
Auto
button 1 to 7 times.
The
sleep
mode is available for 1 to 7 times.
To alter the time
period
in
steps of
press the Sleep Mode Button while
air conditioner.
1
sure
the
Sleep
The
at slow fan
IN COOLING MODE OR HEALTHY
at
DEHUMIDIFICATION MODE:
Mode Auto LED
temperature will automatically rise by 1°C
the next 30 minutes and
over
lights
for comfortable
up.
Setting
operation display.
hour,
aiming
The
3. Make
from the
Sleep Mode will be
speed (cooling) or
medium fan speed (heat pump only) for
quiet sleeping.
2. The Timer is
increments
) disappears
by
2°Cin1hour
sleeping.
the Time
Time can be set only when you have pressed
the Reset button. If you have just replaced the
batteries, the Reset button should be pressed to
3. Press the Time
Setting
buttons until the
desiredtimeisset.
reset the time.
1. Press the
Start/Stop
button.
4. Press the Timer SET button.
2. Press 2nd F button
NOTICE
and check if 2nd F icon is
on.
CANCEL
SET
Check the indicator
for A.M. and P.M.
Delay Start/Pre-Set Stop
1. Make
sure
the time is set
remote control
correctly
on
the
5. To set the selected
2. Press 2nd F button.
SET
receptor.
3. Press the ON/OFF Timer
buttons to turn Timer
CANCEL
time,
press the Timer SET button while
aiming the remote control at the signal
display.
on or
To cancel the timer
off.
ON
OFF
CANCEL
setting
Checkif2ndFiconisoff.
Press the Timer Cancel button while
4. Press the Time
ET
Setting
aiming
remote control at the
buttons until the desired
receptor.
time is set.
(The
timer
and the
NOTICE
Select
one
of the
following
four
lamp on the air conditioner
display will go out.)
types of operation.
with the unit
Delay
OFF Timer
Delay
ON Timer
signal
Delay
OFF and ON Timer
running
Delay
ON and OFF Timer
Owner's Manual
17
Operating
Instructions
Vertical Airflow Direction Control
The
up/down airflow (Vertical Airflow)
adjusted by using the remote control.
can
be
NOTICE
If you press the CHAOS swing button, the horizontal
airflow direction is changed automatically based on the
CHAOS
1. Press the
algorithm to distribute the air in the room
evenly and at the same time to make the human body
feel most comfortable, as if enjoying a natural breeze.
Always use the remote control to adjust the up/down
airflow direction. Manually moving the vertical airflow
direction louver by hand could damage the air
button to start the unit.
Start/Stop
conditioner.
When the unit is shut
2.Open
the door
Press Chaos
on
the remote control.
Swing
off, the up/down airflow direction
system.
louver will close the air outlet vent of the
To
button and the louvers will
adjust left/right(Horizontal Airflow) direction
swing up and down. Press the Chaos Swing
button again to set the vertical louver at the
CAUTION
:
Ensure
unit is turned off before
desired airflow direction.
adjusting the horizontal airflow
direction control.
Carefully open vertical louver to
allow access to the horizontal airflow direction.
Adjust the left/right
Horizontal Airflow Direction Control
The
left/right(Horizontal Airflow) can be adjusted by using
Press the Start/Stop button to start the unit.
Open the door on the
Start/Stop button and
airflow direction
by
hand.
(Optional)
the remote control.
remote control. Press the Airflow Direction
the louvers will
swing
left and
the Horizontal Airflow Direction Control Button
again
right.
Press
to set the
horizontal louver at the desired airflow direction.
Air Circulation Mode
Circulates the
1. Press the
2.
Open
air without
room
Start/Stop
the door
on
cooling
or
heating.
button. the unit will
respond
with
a
beep.
the remote control. Press the Air Circulation button. Close the door
remote control. Now each time that you press the Indoor Fan
shifted from low to CHAOS and back to low again.
CHAOS Air
Fan
speed
is
on
low.
Fan
speed
is
on
Speed Selector,
medium.
Fan
speed
is
the fan
on
on
the
speed
is
high.
NOTICE
CHAOS Air economizes power consumption and prevents overcooling. The fan
from high to low or vice versa, depending on the ambient temperature.
18
Room Air Conditioner
speed
is
automatically changed
Operating
The Button
Instructions
Operation
FORCED OPERATION
The
operation
pressed.
will be started if the power button is
If you want to
stop operation, re-press the button.
FORCED
OPERATION
Cooling Model
Operating
mode
Indoor FAN
Speed
Setting Temperature
Heat pump Model
Room
Temp. ≥ 24°C2 1 °C ≤ Room Temp. < 24°C
Cooling
Cooling
High
High
Healthy
Dehumidification
Healthy Dehumidification
Rule
Room Temp.
<
21°C
Heating
High
22°C2 2 °C2 3 °C2 4 °C
Auto restart
In
case the power comes on again after a power failure, Auto
Restarting Operation is the function to operate procedures
automatically to the previous operating conditions.
If you want to use this operation, press the Auto Restart
Button.
AUTO
RESTART
Helpful information
Fan
speed and cooling capacity.
cooling capacity indicated in the specification is the
value when the fan speed is set to high, and the capacity will
be lower at low or medium fan speed.
High fan speed is recommended when you wish to cool the
room quickly.
The
High
Speed
Owner's Manual
19
Maintenance and Service
Maintenance and Service
CAUTION: Before performing any
maintenance,
turn off the main power to the
system.
Indoor Unit
Never
Grille, Case, and Remote Control
Turn the
system off before cleaning. To clean,
use
any of the
followings:
Waterhotterthan40°C
?
Could
wipewithasoft,drycloth.Donotusebleachor
deformation and/or
cause
discoloration.
abrasives.
Volatile substances
?
Could
NOTICE
the surfaces of the air
damage
conditioner.
Supply power must be disconnected before
cleaning
the indoor unit.
Powder
Gasoline
Air filters
Air outlet vent
(behind front panel)
Vertical louver Horizontal louver
Air inlet vent
1. Lift the front
slightly
panel
remove
2. Clean the filter with
AIR FILTER
and
the filter tab
pull
the filter.
a vacuum or
warm, soapy
water.
The air filters behind the front
checked and cleaned
access
forward to
once
grille
should be
every 2 weeks
?
or more
If dirt is
of
often if neccessary.
?
If
conspicuous, wash with a solution
detergent in lukewarm water.
hot water (40°C or more) is used, it may
be deformed.
3. After
washing
with water,
dry well
in the shade.
4. Re-install the air filter.
30k/32k
36K/38k
1. After
NANO PLASMA FILTER, TRIPLE
DEODORIZING FILTER(OPTIONAL)
to
The PLASMA filter behind the air filters should be
checked and cleaned
more
once
in every 3 months
the air
(You
filters, pull slightly forward
the NANO PLASMA filter.
2. Remove dust with
or
often if necessary.
removing
remove
should not
vacuum
try
cleaner
to wash with
3. Note the cuts of electric
or
air.
water).
discharge
lines.
4. Re-install the NANO PLASMA filter to the
original
position.
1. After
to
TRIPLE DEODORIZING Filter
2.
NANO PLASMA Filter
removing
remove
Dry
in the
the air
filters, pull slightly forward
the TRIPLE DEODORIZING filter.
sunlight
for two hours.
3. Re-install the TRIPLE DEODORIZING filter to
the
Don't touch this PLASMA Filter within 10
seconds after
may
20
cause an
opening
the inlet
electric shock.
Room Air Conditioner
grille,
it
original position.
Maintenance and Service
Replacement of Purifying Filter(Option)
?
Recomended
1.
Open
use
front
period
panel
:
About 2 years
and
air filters.
remove
2. Remove air
3. Insert
new
purifying
air
filters.
purifying
filters.
2
3
Air filter
Air filter
4. Reinsert air filters and close front
panel.
2
3
Triple Deodorizing
Filter
Outdoor Unit
The heat
exchanger coils
and
panel
vents of
(Side)
the outdoor unit should be checked
If
clogged with dirt or
panel vents may
and
regularly.
soot, the heat exchanger
be professionally steam cleaned.
(Rear)
Air intake
vents
Piping
Air outlet
vents
NOTICE
Dirty or clogged coils will reduce the
operating efficiency of the system and
operating costs.
cause
higher
(Side)
(Rear)
Air intake
vents
Air outlet
vents
Piping
Owner's Manual
21
Maintenance and Service
When the air conditioner is not going to be used for a
When air conditioner is not
1.
Operate
the air conditioner
This will
?
dry
on
going
Air circulation mode
long time.
to be used for
(Refer to page 18)
a
long
time.
for 2 to 3 hours.
out the internal mechanisms.
2. Turn off the circuit breaker, and disconnect the
plug.
CAUTION Turn off the circuit breaker when the air conditioner is not
be used for
a
long
Dirt may collect and may
going
to
time.
cause a
fire.
3. Remove the batteries from the remote control.
When the air conditioner is to be used
1. Clean the air filter and install it in the indoor
unit.(Refer to page
2. Check that the air inlet and outlet of the indoor/outdoor unit
are
again.
20 for
cleaning filters.)
not blocked.
Operation Tips
Do not overcool the
room.
Keep
blinds
or
curtains
This is not
good for your
electricity.
health
and wastes
Make
sure
that the doors
Avoid
opening
windows
to
as
keep the
are
shut
much
as
Adjust the
airflow direction to
room
when the air
cool air in the
operation.
Clean the air filter
room.
regularly.
in the air filter
reduce the airflow and lower
cooling
and
dehumidifying
effects. Clean at least
every two weeks.
22
Room Air Conditioner
temperature
uniform
vertical and horizontal
ensure a
temperature in the
Ventilate the
room.
room
occasionally.
Blockages
possible
room
Do not let direct sunshine enter
tight.
doors and
the
the
conditioner is in
and windows
Keep
uniform.
closed.
once
Since windows
are kept closed,
itisagoodideatoopenthem
and ventilate the
then.
room now
and
Maintenance and Service
Troubleshooting
Check the
following points
contact your dealer
or
before
requesting repairs
Case
The air conditioner does not
operate.
?
has
a
persists, please
peculiar
See page
Have you made a mistake in timer operation?
Has the fuse blown or has the circuit breaker
been
room
service.... If the fault
Explanation
?
The
or
service center.
?
odor.
tripped?
-
Check that this is not
the
17
a
damp
walls, carpet, furniture,
or
smell exuded
by
cloth items in the
-
room.
It
is
seems
that condensation
leaking
?
from the air
Condensation
occurs
when the airflow from
the air conditioner cools the
warm room
air.
-
conditioner.
Air conditioner does not
operate
for about 3 minutes
?
This is the
?
Wait about three minutes and
when restarted.
Does not cool
or
protector of the mechanism.
operation
will
heat
?
Is the air filter
dirty?
See air filter
cleaning
20
instructions.
effectively.
?
Has the
?
Are the indoor unit's air inlet
temperature been
set
incorrectly?
or
The air conditioner
is
?
For
a
-
noise that sounds like water
-This is the sound of freon
noisy.
10, 14
outlet vents
obstructed?
operation
-
begin.
flowing
flowing.
inside the
air conditioner unit.
?
For
noise that sounds like the
compressed
atmosphere.
-This is the sound of the dehumidifying water
being processed inside the air conditioning
air
a
releasing
into
-
unit.
Remote control
?
Are the batteries
faint,
?
Are the batteries inserted in the
or no
display is
display at all.
and
Crack sound is heard.
?
(-)
depleted?
opposite (+)
7
directions?
This sound is
generated by the
expansion/constriction of the front panel,
due to changes of temperature.
etc.
-
Owner's Manual
23
Memo
24
Room Air Conditioner