LG | LS-H246VML2 | LG LS-H246VML2 Owner’s Manual

website
http://www.lgservice.com
LG
LG Room
Air Conditioner
OWNER'S MANUAL
MODELS: SV1 Chassis
Prior to
installation, this airconditioning unit must be
submitted for approval by the
utility service which provides
electricity (EN 61000-2,
EN 61000-3 Norm).
IMPORTANT
?
Please read this owner's manual
before
?
installing
and
carefully
operating your
room
and
thoroughly
air conditioner.
Please retain this owner's manual for future reference after
reading
it
thoroughly.
ENGLISHFRAC
Room Air Conditioner Owner's Manual
TABLE OF CONTENTS
FOR YOUR RECORDS
Safety
Precautions.........................3
Write the model and serial numbers here:
Model #
Prior to
Operation
..........................9
Serial #
You
find them
can
on a
label
on
the side of each unit.
Dealer's Name
Introduction ..................................10
Date Purchased
Staple
it to prove
Electrical
Operating
Safety
receipt to this page in the event you need
date of purchase or for warranty issues.
your
...........................11
Instructions.................13
READ THIS MANUAL
Inside you will find many helpful hints on how to use
and maintain your air conditioner properly. Just a little
preventive
Maintenance and Service ............27
care on
your
of time and money
over
you a great deal
the life of your air conditioner.
part
can save
You'll find many answers to common problems in the
chart of troubleshooting tips. If you review our chart of
Troubleshooting Tips first,
you may not need to call
for service at all.
PRECAUTION
?
Contact the authorized service technician for
repair
Contact the installer for installation of this unit.
?
The air conditioner is not intended for
?
?
use
by
young children or invalids without supervision.
Young children should be supervised to ensure
that
Room Air Conditioner
maintenance of this unit.
?
?
2
or
they
When
do not
the
play with
the air conditioner.
power cord is to
replacement work shall be
be
replaced,
performed by
authorized personnel only using only genuine
replacement parts.
Installation work must be performed
in
accordance with the National Electric Code by
qualified and authorized personnel only.
Safety Precautions
Precautions
Safety
To
prevent the injury of the
user or
other
people
and
property damage, the following instructions
must be
followed.
Incorrect
by
operation due to ignoring
following indications.
the
The
meanings
of the
instruction will
cause
harm
or
damage.
This
symbol
indicates the
possibility of
This
symbol
indicates the
possibility of injury or damage
symbols
used in this manual
are as
Be
Be
sure
death
The seriousness is classified
or
serious
ENGLISH
injury.
to
properties only.
shown below.
sure
not to do.
to follow the instruction.
Installation
Do not
For electrical
the power plug
and socket with the ground
work, contact
the dealer, seller, a qualified
electrician, or an Authorized
damaged power
cords, plugs, or a loose
use
socket.
Always
use
terminal.
Service Center.
?
There is risk of fire
or
electric
?
shock.
or
electric
?
panel
and the
Do not
of control box
modify
or
extend the
Do not
There is risk of fire
shock.
install,
remove,
re-install the unit by
power cord.
securely.
?
There is risk of electric shock.
shock.
Install the
cover
There is risk of fire
or
yourself (customer).
or
electric
?
There is risk of fire
shock.
or
electric
?
There is risk of
fire, electric
shock, explosion,
or
injury.
Owner's Manual
3
Safety Precautions
Be cautious when
For
unpacking and installing
the product.
contact the dealer
Sharp edges could cause injury.
Be especially careful of the
case edges and the fins on the
?
condenser and
Be
sure
?
There is risk of
on a
or
product
defective installation
stand.
?
injury.
It may
injury, accident,
damage to the product.
cause
or
evaporator.
the installation
Do not let the air conditioner
area
run
age.
humidity
collapses,
the air
?
conditioner could fall with
it, causing
property damage, product failure,
and
fire, electric
shock, explosion,
does not deteriorate with
If the base
or an
Authorized Service Center.
for
door
?
Do not install the
installation, always
or
a
long
time when the
is very high and a
a window is left open.
Moisture may condense and
wet
or
damage furnishings.
personal injury.
Operation
Take
care
to
ensure
that
Do not
power cords could not be
place anything
Do not turn the
on
the power cord.
air-conditioner ON
pulled out or damaged
during operation.
?
There is risk of fire
or
electrical
shock.
4
Room Air Conditioner
or
OFF
by plugging or unplugging
the power plug.
?
There is risk of fire
shock.
or
electric
?
There is risk of fire
shock.
or
electrical
Safety Precautions
?
Use
a
dedicated outlet for
this
appliance.
There is risk of fire
or
electrical
Grasp the plug
?
shock.
the cord from the outlet. Do
place a heater or
other appliances near the
not touch it with wet hands.
power cable.
to
There is risk of fire
Do not
remove
electrical
or
?
shock.
There is risk of fire and electric
shock.
ENGLISH
Do not allow water to
into electric
Do not store
run
Do not
or use
flammable gas or
combustibles near the air
parts.
use
the
tightly closed
long time.
product
in
space for
a
a
conditioner.
?
It may cause There is risk of
fire, failure of the product, or
?
There is risk of fire
or
failure of
?
Oxygen deficiency
could
occur.
product.
electric shock.
Wax
When flammable gas leaks,
turn off the gas and open a
sounds, odors,
window for ventilation
comes
Unplug
the unit if
or
and close
strange
Stop operation
smoke
the window in storm
from it.
hurricane. If
or
possible,
before turn the
remove
DO NOT
from the window before the
or
?
Thinner
product on.
use the telephone
turn switches
There is risk of
on or
explosion
off.
or
fire.
the air conditioner
hurricane arrives.
?
There is risk of electrical shock
or
fire
?
There is risk of
damage,
property
failure of
product,
or
electric shock.
Owner's Manual
5
Safety Precautions
Do not open the inlet
the product during
is
?
so
of
When the
product is soaked
(flooded or submerged),
not touch the
operation. (Do
electrostatic
grill
contact
filter, if the unit
an
Ventilate the
product from
time to time when operating
it together with a stove, etc.
Authorized
Service Center.
equipped.)
There is risk of
electric
physical injury,
shock, or product
?
There is risk of fire
or
eletric
?
shock.
There is risk of fire
or
electrical
shock.
failure.
Unplug the appliance before
performing cleaning or
When the
product is not be
used for a long time,
disconnect the power supply
plug or turn off the breaker.
maintenance.
?
There is risk of electrical shock.
?
There is risk of
or
failure,
or
product damage
Take
care
nobody
to
ensure
could
step
that
on or
onto the outdoor unit.
?
unintended
This could result in
injury
and
personal
product damage.
operation.
Installation
Always check for gas
(refrigerant) leakage after
installation or repair of
product.
?
Low
refrigerant
cause
failure of
levels may
product.
Install the drain hose to
ensure
away
?
that water is drained
properly.
A bad connection may
water
Keep level even when
installing the product.
leakage.
cause
?
To avoid vibration
or
water
leakage.
90˚
6
Room Air Conditioner
fall
Safety Precautions
Do not install the
where the noise
Use two
product
or
hot air
lift and
from the outdoor unit could
or more
Do not install the
people to
product
where it will be exposed to
sea wind (salt spray)
directly.
transport the air
conditioner.
damage the neighborhoods.
?
It may
cause a
problem
for your
?
Avoid
personal injury.
?
It may
cause
corrosion
on
the
product. Corrosion, particularly
neighbors.
the condenser and
could
or
on
evaporator fins,
product malfunction
inefficient operation.
cause
Operation
Do not direct airflow at
room
occupants. (Don't sit
in the
draft.)
Do not
use
the
product
for
Do not block the inlet
special purposes, such as
preserving foods, works of
art, etc. It is
conditioner,
a consumer
not
a
or
outlet of air flow.
air
precision
refrigeration system.
?
This could
damage
your health.
?
There is risk of
of
Use
not
a
soft cloth to clean. Do
use
harsh
solvents,
?
detergents,
or
loss
?
fire, electric
shock, or damage to the plastic
parts of the product.
?
It may
cause
product failure.
property.
Do not touch the metal
Do not
parts of the product when
anyting on the product.
(outdoor units)
removing the air filter. They
are very sharp!
etc.
There is risk of
damage
There is risk of
personal injury.
?
step
on or
put
There is risk of
and failure of
personal injury
product.
Owner's Manual
7
ENGLISH
Safety Precautions
Always insert the filter
securely. Clean the filter
every two weeks or
often if necessary.
A
objects through
more
or
filter reduces the
dirty
efficiency
?
Do not insert hands
and could
Use
a
There
and
product
or damage.
maintaining
ladder when
or
drained from the unit.
are
sharp
parts that could
in.
moving
cause personal
?
It is not
cause
sanitary
and could
serious health issues.
injury.
cause
firm stool
Do not drink the water
outlet while the air
plugged
?
other
the air inlet
conditioner is
of the air conditioner
malfunction
or
cleaning
or
the air conditioner.
Replace the
all batteries in the remote
control with
new ones
not mix old and
new
of the
same
batteries
or
type. Do
different
types of batteries.
Be careful and avoid
?
personal injury.
?
There is risk of fire
or
explosion
Disuse
Do not
recharge
or
batteries. Do not
disassemble the
dispose
of batteries in
If the
liquid
from the batteries
gets
onto
your skin or clothes, wash it well with clean
water. Do not use the remote if the batteries
a
fire.
have leaked.
?
They
may burn
or
explode.
?
The chemicals in batteries could
other health hazards.
8
Room Air Conditioner
cause
burns
or
Prior to
Prior to
for
Preparing
1. Contact
2.
Operation
Operation
installation
in the power
Plug
3. Use
an
Operation
specialist
plug properly.
for installation.
ENGLISH
dedicated circuit.
a
4. Do not
use an
extension cord.
5. Do not
6. If the
start/stop operation by plugging/unplugging the power cord.
cord/plug is damaged, replace it with only an authorized replacement part.
Usage
1.
Being exposed
to direct airflow for
3.
Cleaning
or
and Maintenance
1. Do not touch the metal
2. Do not
3.
long
plants
Due to the possibility of oxygen deficiency, ventilate the room when using the appliance together with
stoves or other heating devices.
Do not use this air conditioner for non-specified special purpose (e.g. preserving precision devices,
food, pets, plants, or art objects). Such use may damage your properties.
occupants, pets,
2.
time may be hazardous to your health. Do not expose
to direct airflow for a long time.
a
use
parts of the unit when removing the filter. Injury
water to clean inside the air conditioner.
Exposure
to water
can occur.
can
destroy
the
insulation,
leading to electric shock.
When cleaning the unit, first make sure that the power and breaker are turned off. The fan rotates at
very high speed during operation. There is a possibility of injury if the unit's power is triggered while
cleaning inner parts of the unit.
a
Service
For
repair and maintenance,
contact your authorized service dealer.
Owner's Manual
9
Introduction
Introduction
Symbols
used in this Manual
This
symbol
This
symbol
alerts you to the risk of electric shock.
alerts you to hazards that may
air conditioner.
This
NOTICE
symbol
indicates
special
cause
harm to the
notes.
Features
WARNING: This
appliance should be installed in accordance with national wiring
regulations. This guide acts as a guide to help to explain product features.
NEO Air Filter
Indoor
Air Inlet
Front Panel
Power Cord
Signal Receptor
Air
Discharge
Outdoor
Air Intake Vents
Connecting
Wires
Piping
Air Outlet Vents
Base Plate
10
Room Air Conditioner
Drain Hose
Electrical
Electrical
Safety
WARNING: This
To minimize the risk of electric
Safety
appliance
shock, you
must
must be
alway plug
properly grounded.
into
a
grounded
oulet.
Preferred method
Ensure proper ground
exists before use
WARNING:
power
Do not cut
or remove
the
grounding
prong from the
plug.
WARNING:
adapter ground terminal to the wall
receptacle cover screw does not ground the appliance unless the
cover screw is metal and not insulated, and the wall receptacle is
grounded through the house wiring.
Attaching
the
WARNING:
If you have any doubt whether the air conditioner is
grounded, have the wall receptacle and circuit checked
properly
a qualified
by
electrician.
Owner's Manual
11
Electrical
Safety
Temporary Use
of an
Adapter
We
strongly discourage the use of an adapter due to potential safety hazards. For temporary
connections, use only a UL-listed adapter, available from most local hardware stores. Ensure that the
large slot in the adapter is aligned with the large slot in the receptacle for a proper polarity connection.
To disconnect the power cord from the adapter, use one hand on each to avoid damaging the ground
terminal. Avoid frequently unplugging the power cord as this can lead to eventual ground terminal
damage.
Temporary
method
Adapter Plug
Metal Screw
Receptacle
WARNING: Never
Temporary Use
use
the
appliance with
Cover
a
broken
adapter.
of an Extension Cord
We
strongly discourage the use of an extension cord due to potential safety hazards. For temporary
situations, use only CSA certified and UL listed 3-wire grounded extension cords, rated 15 A, 125 V.
12
Room Air Conditioner
Operating
Instructions
Instructions
Operating
How to insert the Batteries
1. Remove the
battery
cover
by pulling
it
according
to the
arrow
ENGLISH
direction.
2. Insert
new
installed
batteries
sure
that the
(+)
and
(-)
of
battery
are
correctly.
3. Reattach the
NOTICE
cover
by sliding
it back into
position.
Use 2
Do
Storage
?
making
AAA(1.5volt) batteries.
not use rechargeable batteries.
and
Tips for using the Remote Controller
The remote controller may be stored
it on a wall.
by mounting
?
To
operate the
conditioner, aim the
the signal receptor.
room
remote controller at
air
Signal receptor
Receives the
signals from
the remote
controller.(Signal receiving
sound: two short
beeps
or one
long beep.)
Operation indicating lamps
On/Off
Lights
up
during
:
Lights
up
during Sleep
Timer
:
Lights
up
during
Defrost Mode
:
Lights up during Defrost Mode or *Hot
Start operation (Heat pump model only)
Outdoor Unit
:
Lights up during outdoor
(Cooling model only)
Sleep
Mode
Operation
NEO Plasma
*Hot Start
the
:
operation: Stops
:
system operation.
Timer
Mode Auto
operation.
unit
The function illustrates its
the indoor fan in
operation.
operation.
dynamic
Heating Operation
mode
to
Operation indicating lamps
by using
a
multiple lighting system.
prevent cold air from blowing
out from unit.
Owner's Manual
13
Operating
Instructions
Remote Control
The controls will look like the
Operations
following.
Controls
Signal
transmitter
1. START/STOP BUTTON
Operation starts when this button is pressed
and stops when the button is pressed again.
2. OPERATION MODE SELECTION BUTTON
Used to select the operation mode.
3. ROOM TEMPERATURE SETTING
BUTTONS
Used to select the room temperature.
4. INDOOR FAN SPEED SELECTOR
Used to select fan speed in four steps
low, medium, high and CHAOS.
5
5. JET COOL/HEATING(OPTIONAL)
Used to start or stop the speed
1
cooling/heaing.(speed cooling/heating operates
super high fan speed in cooling/heatig mode.)
6
6. CHAOS SWING BUTTON
Used to stop or start louver movement and
set the desired up/down airflow direction.
3
4
7. ON/OFF TIMER BUTTONS
Used to set the time of starting and
10
2
CANCEL
operation. (See
9
7
ON
12
AUTO CLEAN
11
8
17
13
14
15
16
24)
8. TIME SETTING BUTTONS
Used to adjust the time. (See page
SET
OFF
page
stopping
24)
9. TIMER SET/CANCEL BUTTON
Used to set the timer when the desired time
is obtained and to cancel the Timer
operation. (See
page
24)
10. SLEEP MODE AUTO BUTTON
Used to set Sleep Mode Auto operation.
(See
page
24)
11. AIR CIRCULATION BUTTON
Used to circulate the room air without
Flip-up door
(opened)
Operation
Mode
Operation
Healthy
or
Auto
Operation
Cooling Model(
),
Heat
Pump Model(
page
12. ROOM TEMPERATURE CHECKING
BUTTON
Used to check the room temperature.
)
(OPTIONAL)
Used to set Auto Clean mode.
Room Air Conditioner
(See
page
22)
16. 2nd F Button
Used prior to using modes printed in blue
at the bottom of buttons. (See page 23)
17. AUTO CLEAN
14
25)
15. RESET BUTTON
Used prior to resetting time.
Heating Operation
?
heating. (See
14. HORIZONTAL AIRFLOW DIRECTION
CONTROL BUTTON (OPTIONAL)
Used to set the desired vertical airflow
direction.
Changeover
Dehumidification
or
13. NEO PLASMA(OPTIONAL)
Used to start or stop the
plasma-purification function.
Cooling Operation
Auto
cooling
Operating
Instructions
Cooling operation
1
2
Start/Stop button.
The unit will respond with
a beep.
Open the door of the remote controller. To select Cooling
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the
Healthy
Heating
Dehumidification
(Heat pump model only)
Close the door of the remote controller. Set the
lower than the
set within
a
room
temperature
temperature. The temperature can be
range of 18°C~30°Cat intervals of 1°C.
ON
4
arrow.
Auto
Cooling
3
ENGLISH
Press the
Set the fan
temperature
To lower the
temperature
speed again
To raise the
with the door
of the remote controller still closed.
You
speed in four
steps-low, medium, high and CHAOS.
Each time the button is pressed, the
fan speed mode is shifted.
select the fan
by the CHAOS logic
Natural wind
For fresher
blows like
can
a
feeling,
press the Indoor fan
natural breeze
speed selector and set to CHAOS
by automatically changing fan speed according
mode. In this
mode, the wind
to the CHAOS
logic.
Owner's Manual
15
Operating
Auto
Instructions
operation (Cooling
model
only)
Press the
1
Start/Stop button.
The unit will respond with
a beep.
2
Open the door of the remote controller. To select Auto
Operation, press the operation mode selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the
Cooling
ON
3
The
arrow.
Auto
temperature and fan speed
electronic controls based
on
Healthy
Heating
Dehumidification
(Heat pump model only)
are
automatically
the actual
room
set
by
the
temperature. If
change the set temperature, press the Room
Temperature Setting buttons. The cooler or warmer you feel,
the more times (up to two times) you should press the button.
The set temperature will be changed automatically.
you want to
To raise the
temperature
To lower the
temperature
During Auto Operation
You cannot control the indoor fan
already been set by the Fuzzy rule.
If the system is not operating as desired, manually switch to another mode. The system will not
automatically switch from the cooling mode to the heating mode, or from heating mode to cooling
mode, it must be done by manually resetting.
During Auto Operation, pressing the chaos swing button makes the horizontal louvers swing up and
down automatically. If you want to stop auto-swing, press the chaos swing button again.
16
Room Air Conditioner
speed.
It has
Operating
Auto
changeover operation(Heat
pump model
Instructions
only)
Press the
1
Start/Stop button.
The unit will respond with
a beep.
2
Open the door of the remote controller. To select Auto Changeover
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is shifted in the
direction of the
arrow.
Cooling
3
ENGLISH
Auto
changeover
Healthy
Dehumidification
Heating
(Heat pump model only)
Close the door of the remote controller. Set the
lower than the
set within
a
room
temperature
temperature. The temperature can be
range of 18°C~30°Cat intervals of 1°C.
To raise the
temperature
To lower the
temperature
ON
4
Set the fan
speed again
with the door
of the remote controller still closed.
You
speed in four
steps-low, medium, high and CHAOS.
Each time the button is pressed, the
fan speed mode is shifted.
During Auto changeover Operation
The air conditioner changes the operation
temperature vary over
temperature within ±2°C
mode
can
select the fan
automatically to keep indoor temperature. When
±2°C with respect to setting temperature, air conditioner keeps the
with respect to setting temperature by auto changeover mode.
room
room
Owner's Manual
17
Operating
Instructions
Healthy
dehumidification
operation
Press the
1
Start/Stop button.
The unit will respond with
a beep.
2
Open
the door of the remote controller. To select
Dehumidification
Operation,
press the
Healthy
Operation Mode
Selection button.
Each time the button is
pressed,
shifted in the direction of the
3
speed again
operation
mode is
arrow.
Auto
Cooling
Set the fan
the
Healthy
Heating
Dehumidification
(Heat pump model only)
with the door
of the remote controller still closed.
You
speed in four
steps-low, medium, high, or CHAOS.
Each time the button is pressed, the
fan speed mode is shifted.
ON
can
Natural wind
For fresher
select the fan
by the CHAOS logic
feeling,
press the Indoor Fan
to CHAOS mode. In this
breeze
Speed
Selector and set
mode, the wind blows like
by automatically changing
CHAOS logic.
fan
a
speed according
natural
to the
During Healthy Dehumidification Operation
If you select the dehumidification mode on the operation selection button, the A/C starts to run the
dehumidification function. It automatically sets the room temp. and airflow volume to the best condition
for
dehumidification, based
on
In this case, however, the setting
control the room temp. either.
the sensed current
temp. is
not
room
displayed
temp.
on
the remote controller and you
are
not able to
During the healthy dehumidification function, the airflow volume is automatically set according to the
optimization algorithm responding to the current room temp. status, so that the room condition is kept
healthy and comfortable even in the very humid season.
18
Room Air Conditioner
Operating
Instructions
Heating operation (Heat
pump model
only)
ENGLISH
Press the
1
Start/Stop button.
The unit will respond with
a beep.
2
Open the door of the remote controller. To select Heating
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the
Auto
Cooling
3
arrow.
Healthy
Dehumidification
Heating
(Heat pump model only)
Close the door of the remote controller.
Set the
temperature higher than the room temperature.
The temperature can be set within a range of 16°C~30°Cat
intervals of 1°C.
ON
4
Set the fan
To raise the
temperature
To lower the
temperature
speed again
with the door of the
remote controller still closed. You
select the fan
speed
in four
can
steps--low,
medium, high and CHAOS. Each time the
button is
pressed,
the fan
speed
mode is
shifted.
Natural wind by the CHAOS
For fresher
feeling,
wind blows like
a
logic
press the Indoor Fan
natural breeze
Speed Selector and set to CHAOS
by automatically changing fan speed according
mode. In this
to the CHAOS
mode, the
logic.
Owner's Manual
19
Operating
Instructions
Jet cool
operation
Press the
1
Start/Stop button.
The unit will respond with
a beep.
2
Press the Jet Cool button to
the
speed cooling
will
operate
on
3
cooling
operate
mode and the unit
at super
high
fan
speed
mode for 30 minutes.
To cancel the Jet Cool
mode, press the Jet Cool button, the
fan speed button or the room temperature setting button
again and the unit will operate at high fan speed on cooling
mode.
or
or
NOTICE
During the JET COOL function at any moment, the A/C starts to blow the cool air at extremely
high speed for 30 minutes setting the room temp. automatically to 18°C. It is especially used to
cool the room temp. quickly in a hot summer.
In heat pump mode, neuro
function is not available.
fuzzy mode,
In order to return to the normal
mode selection
auto
changeover
mode
mode from the JET COOL
however, the JET COOL
mode, just press the operation
button, airflow volume selection, temp. setting button
again.
20
cooling
or
Room Air Conditioner
or
the JET COOL button
Operating
Jet heat
Instructions
operation (Optional)
Press the
1
Start/Stop button.
The unit will respond with
a beep.
2
Open
ENGLISH
the door of the remote controller.
To select
Heating Operation.
Auto
Cooling
Healthy
Dehumidification
changeover
Press the Jet Heat button to
3
speed heating
operate
Heating
(Heat pump model only)
operate the
mode and the unit will
at super
high
fan
speed
on
heating
mode for 60 minutes.
ON
To cancel the Jet Heat
mode, press the Jet Heat button,
the fan speed button or the room temperature setting
button again and the unit will operate at high fan speed on
4
heating
mode.
or
or
NOTICE
During the JET HEAT function at any moment, the A/C starts to blow the heat air at extremely high speed for
60 minutes setting the room temp. automatically to 30°C. It is especially used to heat the room temp. quickly
in
a
On
cool winter.
cooling, healthy
dehumidification mode
or
auto
changeover mode, however,
the JET HEAT function is not
available.
In order to return to the normal
selection
heating
mode from the JET HEAT
button, airflow volume selection, temp. setting button
or
mode, just press the operation mode
the JET HEAT button
again.
Owner's Manual
21
Operating
Instructions
NEO PLASMA
purification operation(Optional)
1
Press the
The unit
Start/Stop button.
will respond with a
beep.
2
Open
the door of the remote
controller. Press the PLASMA
button.
Operation will start when the button
is pressed and stop when the button
is pressed again.
3
Set the fan
speed again
controller closed. You
with the door of the remote
can
select the fan
speed
in four
steps-low, medium, high or CHAOS.
Each time the button is pressed, the fan
speed mode is shifted.
Air
purifying operation (PLASMA) can be
with cooling, Heating or any other operations.
NEO PLASMA Air
Purifying Operation only
If you press the only PLASMA button, only
PLASMA purification function operates.
Then, fan speed is low. You can select the fan
speed in four steps-low, medium, high or
CHAOS.
Each time the button
speed
22
Room Air Conditioner
(
mode is shifted.
)
is
pressed,
the fan
Operating
2nd F
Instructions
operation
1
Start/Stop button.
The unit will respond with
a beep.
2
Open
ENGLISH
Press the
the door of the remote control and press the 2nd
Function button to operate functions printed in blue unter
buttons.
(Check the indication
remote controller.)
These buttons
can
of 2nd function
set the timer
ON
as
on
the
display
of the
follows:
OFF
SET
CANCEL
ON
OFF
SET
AUTO CLEAN
3
For
2nd function
the button is
more
disappears in a
pressed again.
short time
details, refer to functions
automatically or when
next pages.
Owner's Manual
23
Instructions
Operating
Additional Features
Sleep
1. Press the
mode
Mode Auto button to set the time you want the unit to
Sleep
2. The Timer is
in one-hour increments
programmed
mode is available for 1 to 7 times. To
sleep
stop automatically.
by pressing the Sleep Mode Auto button 1 to 7 times. The
alter the time period in steps of 1 hour, press the Sleep Mode
Button while
3.
aiming at air conditioner.
Make sure the Sleep Mode Auto LED lights up.
To cancel the Sleep Mode, press the sleep Mode
(
) disappears from the operation display.
The
Sleep Mode will be operated
only) for a comfortable sleep.
NOTICE
In
at slow fan
healthydehumidification mode:
The temperature will automatically rise by 1°C over the
sleep.
cooling
mode
Auto button several times until the star
Setting
1. Time
speed (cooling)
or
medium fan
speed (heat
pump
or
next 30 minutes and
by
2°C in 1 hour for
a
comfortable
the time
you press the Reset button. Having replacing the batteries,
you should press the reset buttons to reset the time. Press the Start/Stop button.
can
be set
only when
2. Press 2nd F button and check if 2nd F icon is
3. Press the Time
Setting
on.
buttons until the desired time is set.
CANCEL
4. Press the Timer SET button.
SET
NOTICE
Check the indicator for A.M. and P.M.
Delay
1. Make
sure
start/Pre-set
the time is set
stop
correctly on
the
display of the
remote controller.
2. Press 2nd F button.
3. Press the ON/OFF Timer buttons to turn Timer
4. Press the Time
Setting
on or
off.
ON
OFF
buttons until the desired time is set.
CANCEL
5. To set the selected
time, press the Timer setting button aiming the
remote controller at the
SET
signal receptor.
To cancel the timer
setting
Check if 2nd F icon is off.
CANCEL
Press the Timer Cancel button
(The timer lamp
NOTICE
Select
Delay
24
on
aiming
the remote controller at the
the air conditioner and the
one
of the
following
OFF Timer
Room Air Conditioner
four
Delay
display will
go
SET
out.)
types of operation.
ON Timer
signal receptor.
Delay
with the unit
OFF and ON Timer
running
Delay
ON and OFF Timer
Instructions
Operating
Airflow direction control
The
up/down and right/left airflow
using the remote control.
be
can
Press Chaos
adjusted by
Swing
Press the button
30
Press the
button to start the unit.
Start/Stop
button and the louvers will
and the louvers will
again
minutes, the louvers
swing.
stop. After
return to the maximum airflow
position automatically.
Air circulation mode
Circulates the
1. Press the
2.
Open
air without
room
Start/Stop
the door
cooling
or
heating.
button. the unit will
respond
a
beep.
the remote control. Press the Air Circulation button. Close the door
on
Now each time that you press the Indoor Fan
and back to low again.
CHAOS Air
NOTICE
with
Speed Selector,
Fan
speed
is
on
low.
the fan
Fan
speed
speed
is
on
on
the remote control.
is shifted from low to CHAOS
medium.
Fan
speed
is
on
high.
CHAOS Air economizes power
automatically changed
from
consumption and prevents overcooling. The fan speed is
high to low or vice versa, depending on the ambient temperature.
Auto clean
1. Whenever you press the Auto Clean
button, Auto Clean Function will be reserved and cancelled.
2. Auto Clean function works before and after
AUTO CLEAN
the below
cooling
or
dehumidification mode. For
details, refer to
points.
3. When the unit is started after the reservation of Auto Clean
,the Cool Start function operates and
indoor Fan is started after 20 seconds.
4. When you press Start/Stop button to turn off the unit after the you have reserved Auto Clean
function, the air-conditioner circulates the indoor air in the Auto Clean mode with no more
Cooling
pump
or
Dehumidification
model, for
operation.
For
Cooling only model,
it lasts for 30 minutes for Heat
16 minutes.
5. If you press the auto clean button
cancelled.
again during the product operation
,
Auto Clean function will be
NOTICE
During
Auto Clean
Dehumidification
During
function, moistures left in indoor units after Cooling Operation
Operation
Auto Clean
can
or
Healthy
be removed.
function, only Start/Stop button, Plasma button and Auto Clean button
are
available.
Owner's Manual
25
ENGLISH
Instructions
Operating
Forced
operation
Operation procedures when the remote control can't be used.
The operation will be started if the power button is pressed.
If you want to stop operation, re-press the button.
Power button
Cooling
Heat pump Model
Model
Room Temp. ≥ 24°C2 1 °C ≤ Room Temp.
<
24°C
Room
Temp. < 21°C
Operating
mode
Cooling
Cooling
Healthy Dehumidification
Heating
Indoor FAN
Speed
High
High
High
High
22°C2 2 °C2 3 °C2 4 °C
Setting Temperature
Test
operation
During
the TEST
temperature and
OPERATION, the unit operates in cooling mode
high speed fan, regardless
of
room
resets in 18 minutes.
During test operation,
If you want to
at
use
if remote controller
this
operation,
signal
is
received, the unit operates
as
remote controller sets.
Press and hold the ON/OFF button for 3~5seconds, then the buzzer sound 1
"beep".
If you want to
stop the operation, re-press the button.
Auto restart
In
again after a power failure, Auto Restarting Operation is the function to operate
procedures automatically to the previous operating conditions.
So there is no need of activating this function by pressing any key or button.
In the initial mode, the fan operates at a low speed and the compressor starts 2.5~3minutes later.
As the compressor starts, the fan speed also resumes its previous setting mode.
case
the power
Helpful
comes on
information
Fan
speed and cooling capacity.
The cooling capacity indicated in the specification is the value
when the fan speed is set to high, and the capacity will be lower at
low or medium fan speed.
High fan speed is recommended when you wish to cool the room
quickly.
High
Speed
NOTICE
Auto restart function has set enable
But customer
can
set up
as
by following
factory default.
this instruction.
To be disable function
-
Press and hold the ON/OFF button for 6
seconds, then the buzzer sound
2
"beep"
and the indicator
lamp (1)
seconds, then the buzzer sound
2
"beep"
and the indicator
lamp (1)
blinks 4 times.
To be enable function
-
Press and hold the ON/OFF button for 6
brights
26
4 times.
Room Air Conditioner
Maintenance and Service
Maintenance and Service
Indoor Unit
WARNING: Turn the
Do not
NOTICE
use
Supply
bleach
system off before cleaning. To clean, wipe with
a
soft, dry cloth.
abrasives.
or
power must be disconnected before
cleaning
the indoor unit.
Air filter
The air filters behind the front
grill
should be checked and cleaned
every 2 weeks or more often if neccessary.
1. Pull up the front panel. After lifting up the filter tab
filter out
NOTICE
bit, take the
1
slowly
Clean the filter after
2. Clean the filter with
?
a
once
If dirt is
stopping
a vacuum or
conspicuous,
the
2
product.
warm, soapy water.
wash with
a
solution of
detergent
in
lukewarm water.
(40°C or more) is used, it may be deformed.
After washing with water, dry well in the shade.
?
3.
If hot water
Filter
4. Re-install the air filter.
Never
?
use
followings:
Water hotter than 40°C.
Could
?
any of the
cause
deformation and/or discoloration.
Volatile substances
Could
damage
the surfaces of the air conditioner.
Outdoor Unit
The heat
exchanger coils and panel vents of the outdoor unit should
clogged with dirt or soot, the heat exchanger and panel vents may
be checked
If
be
NOTICE
Dirty or clogged
operating costs.
coils will reduce the
operating efficiency
regularly.
professionally steam
of the
system and
cause
cleaned.
higher
Air Intake Vents
Connecting
Wires
Piping
Air Outlet Vents
Base Plate
Drain Hose
Owner's Manual
27
ENGLISH
Maintenance and Service
Cleaning
?
Recomended
1. Lift the front
Filter
use
period
panel,
:
About 3 months
hold it up and
pull
the Air filter.
2. Remove the Plasma Filters.
WARNING: Don't touch the PLASMA Filter
within 10 seconds after
grille,
it may
cause
opening
the inlet
electric shock.
3. Put the Plasma Filters into the neutral
detergent
for 1~2
hours and then raise them.
4. Insert the Plasma Filters after
perfectly drying
them in
shade.
Now insert Air Filter and close the front
by matching
panel completely
the hook.
Hook
Hanger
Air Filter
Front Panel Hook
28
Room Air Conditioner
Maintenance and Service
Common Problems and Solutions
Before
calling
for service
If you have problems with your air conditioner, read the following information and try to solve
the problem. If you cannot find a solution, turn off the air conditioner and contact your dealer.
Air conditioner does not
operate
1. Ensure that the air conditioner is
2. Check the fuse
or
plugged
into
a
proper outlet.
circuit breaker.
3. Check whether the
voltage
is
unusually high
or
low.
Air does not feel cold
1.
2.
enough on the cooling setting
Ensure that the temperature settings are correct.
Check to see if the air filter is clogged with dust. If so, replace
the filter.
3. Ensure that the air flow from the outside is not obstructed and that there is
over
20" between the back of the air conditioner and the wall
4. Close all doors and windows and check for any
Before
calling
for
source
or
a
clearance of
fence behind it.
of heat in the
service, please review the following list of
room.
common
problems
and
solutions.
The air conditioner is
?
You hear
or
in
and
?
a
pinging
operating normally when:
noise. This is caused
highly humid conditions. This
improve cooling efficiency.
by
feature is
water
being picked up by
designed to help remove
You hear the thermostat click. This is caused
by
the compressor
the fan
on
rainy days
moisture in the air
cycle starting
and
stopping.
?
You
see
highly
water
dripping
humid conditions
from the
or on
of the unit. Water may be collected in the base pan in
days. This water overflows and drips from the rear of
rear
rainy
the unit.
?
You hear the fan
running
while the compressor is silent. This is
a
normal
operational
feature.
Owner's Manual
29
ENGLISH
Maintenance and Service
Troubleshooting
The air conditioner may be
operating abnormally
when:
Possible Causes
Problem
The air conditioner is
What To Do
?
unplugged.
?
the air conditioner
is
plug
into the outlet.
Check the house fuse/circuit breaker
box and
tripped.
Air
sure
pushed completely
The fuse is blown/circuit
breaker is
Make
replace
the fuse
or
reset the
breaker.
conditioner
does not start
Power failure.
?
If power failure occurs, turn the mode
control to Off.
When power is restored, wait 3
minutes to restart the air conditioner
to
prevent tripping of the compressor
overload.
Airflow is restricted.
?
Make
sure
blinds,
or
there
are no
furniture
curtains,
blocking
the front of
the air conditioner.
The thermostat may not be
set
?
Turn the knob to
?
Clean the filter at least every 2 weeks.
See the care and Maintenance
high enough.
The air filter is
dirty.
higher number.
The highest setting provides
maximum cooling.
a
section.
Air
The
conditioner
room
may have been
?
hot.
on, you need to allow time for the
room to cool down.
does not cool
as
When the air conditioner is first turned
it should
Cold air is
Cooling
escaping.
coils have iced up.
?
Check for open furnace floor
and cold air returns.
?
See Air Conditioner
registers
Freezing Up
below.
Air
Ice blocks the air flow and
conditioner
stops the air conditioner from
freezing
cooling
*
You
30
can
up
refer to the
the
Energy
Room Air Conditioner
?
Set the mode control at
High
Fan
Cool with thermostat at 1
room.
Star program in detail at
High
www.energystar.gov.
or
or
2.
Download PDF

advertising