LG | XSNH096TEA0 | LG XSNH096TEA0 Owner’s Manual

ENGLISH
FRANÇAIS
OWNER’S MANUAL
AIR
CONDITIONER
Please read this manual carefully before operating
your set and retain it for future reference.
TYPE : WALL MOUNTED
MODELS : XS-H096TEA0
XS-H126TEA0
XS-H186TEA0
XS-H246TEA0
EOSANMC
EOSANMC
EOSANMC
EOSANMC
The equipment complies with requirements of the Technical Regulation,
in terms of restrictions for the use of certain dangerous substances in
electrical and electronic equipment.
www.lg.com
2
TIPS FOR SAVING ENERGY
ENGLISH
TIPS FOR SAVING ENERGY
Here are some tips that will help you minimize the power consumption when you use the air
conditioner. You can use your air conditioner more efficiently by referring to the instructions
below:
• Do not cool excessively indoors. This may be harmful for your health and may consume more
electricity.
• Block sunlight with blinds or curtains while you are operating the air conditioner.
• Keep doors or windows closed tightly while you are operating the air conditioner.
• Adjust the direction of the air flow vertically or horizontally to circulate indoor air.
• Speed up the fan to cool or warm indoor air quickly, in a short period of time.
• Open windows regularly for ventilation as the indoor air quality may deteriorate if the air
conditioner is used for many hours.
• Clean the Air filter once every 2 weeks. Dust and impurities collected in the Air filter may
block the air flow or weaken the cooling / dehumidifying functions.
For your records
Staple your receipt to this page in case you need it to prove the date of purchase or for warranty
purposes. Write the model number and the serial number here:
Model number :
Serial number :
You can find them on a label on the side of each unit.
Dealer’s name :
Date of purchase :
IMPORTANT SAFETY INSTRUCTIONS
3
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
Always comply with the following precautions to avoid dangerous situations and ensure peak
performance of your product
! WARNING
It can result in serious injury or death when the directions are ignored
! CAUTION
It can result in minor injury or product damage when the directions are ignored
! WARNING
• Installation or repairs made by unqualified persons can result in hazards to you and others.
• Air conditioner Shall be installed in accordance with national wiring regulations.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
• The information contained in the manual is intended for use by a qualified service technician
familiar with safety procedures and equipped with the proper tools and test instruments.
• Failure to carefully read and follow all instructions in this manual can result in equipment malfunction, property damage, personal injury and/or death.
• This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• When the power cord is to be replaced, replacement work shall ve performed by authorized
personnel only using only genuine replacement parts.
Installation
• Use a standard circuit breaker and fuse conforming with the rating of the air conditioner. Failure to do so may result in electric shock or product failure.
• Contact an authorized service center when you install or relocate the air conditioner. Failure to
do so may result in serious injury or product failure.
• Always use a power plug and socket with a ground terminal. Failure to do so may result in
electric shock or product failure
• Install the panel and the cover of the control box safely. Failure to do so may result in explosion or fire.
• Install a dedicated electric outlet and circuit breaker before you use the air conditioner. Failure
to do so may result in electric shock or product failure.
• Use a standard circuit breaker and fuse conforming with the rating of the air conditioner. Failure to do so may result in electric shock or product failure.
• Do not modify or extend the power cable. If the power cable or cord has scratches or skin
peeled off or deteriorated then it must be replaced. It may result in fire or electric shock.
• Be cautious when you unpack or install the air conditioner. Failure to do so may result in serious injury or product failure.
• Contact an authorized service center when you install or relocate the air conditioner. Failure to
do so may result in serious injury or product failure.
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
4
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
• Do not install the air conditioner on an unstable surface or where there may be a danger of it
falling. It may result in death, serious injury, or product failure.
• Use inflammable gas (nitrogen) to inspect leak and to purge air, using compressed air or flammable gas may cause fire or explosion.
• Please keep the protective film of reset switch. It is used to protect the PCB from ESD damage.
Operation
• Do not let the air conditioner run for a long time when the humidity is very high or when a door or
window has been left open. Failure to do so may result in product failure.
• Make sure that the power cord is not pulled or damaged while the air conditioner is operating. Failure to do so may result in fire, electric shock, or product failure.
• Do not place any objects on the power cord. It may result in electric shock or product failure.
• Do not turn on or off the air conditioner by plugging in or unplugging the power plug. It may result in
fire or electric shock.
• Do not touch, operate or repair the air conditioner with wet hands. It may result in electric shock or
product failure.
• Do not place a heater or other heating appliances near the power cable. It may result in fire, electric
shock, or product failure.
• Do not allow water to run into the air conditioner. It may result in explosion or fire.
• Do not leave flammable substances such as gasoline, benzene and thinner near the air conditioner.
It may result in explosion or fire.
• Do not use the air conditioner for an extended period of time in a small place without ventilation.
Ventilate the place regularly. Failure to do so may result in explosion or fire.
• When there is a gas leak, ventilate sufficiently before using the air conditioner again. Failure to do so
may result in explosion or fire.
• Unplug the power plug if there is a noise, smell or smoke coming from the air conditioner. Failure to
do so may result in explosion or fire.
• Stop operating and close the window in strom or hurricane. If possible remove the product from the
window before hurricane arrives
• Do not touch the electrostatic filter after opening the front grille. Failure to do so may result in electric shock or product failure.
• Contact an authorized service center when the air conditioner is submerged into water due to flooding. Failure to do so may result in explosion or fire.
• Be cautious water could not enter the product.
• Make sure to ventilate sufficiently when this air conditioner and a heating appliance such as a heater
are used simultaneously. Failure to do so may result in fire, serious injury, or product failure.
• Turn the main power off and unplug the power plug when you clean or repair the air conditioner.
Failure to do so may result in death, serious injury, or product failure.
• Unplug the power plug when the air conditioner is not used for an extended period of time. Failure
to do so may result in product failure.
• Do not place any objects on the air conditioner. It may result in product failure.
! WARNING
• For inner cleaning, contact an Authorized Service Center or a dealer. Do not use harsh detergent
that causes corrosion or damage on the unit. Harsh detergent may also cause failure of product, fire,
or electronic shock.
IMPORTANT SAFETY INSTRUCTIONS
5
• Make sure to check if there is a refrigerant leak after you install or repair the air conditioner. Failure
to do so may result in product failure.
• Install the drain hose properly for smooth drainage of condensed water. Failure to do so may result
in product failure.
• Keep level even when installing the product.
• Install the air conditioner where the noise from the outdoor unit or the exhaust gas will not inconvenience the neighbors. Failure to do so may result in conflict between neighbors.
• When transporting the equipment, there should be at least 2 or more people, or a forklift. It may result in serious injury.
• Do not install the air conditioner where it will be exposed to sea wind (salt spray) directly. It may result in product failure.
Operation
• Do not expose people, animals or plants to the cold or hot wind from the air conditioner. It may result in serious injury.
• Do not use the product for special purposes, such as preserving foods, works of art, etc. It is a consumer air conditioner, not a precision refrigeration system. It may result in death, fire or electric
shock.
• Do not block the inlet or outlet of air flow. It may result in explosion or product failure.
• Do not use strong cleaning agents or solvents when you clean the air conditioner, or spray water.
Use a smooth cloth. It may result in serious injury or product failure.
• Never touch the metal parts of the air conditioner when you remove the Air filter. It may result in serious injury or product failure.
• Do not place any objects on the air conditioner. It may result in product failure.
• Always insert the filter securely after cleaning. Clean the filter every two weeks or more often if
necessary.
• Do not insert hands or other objects through the air inlet or outlet while the air conditioner is operating. It may result in electric shock.
• Do not drink the water drained from the air conditioner. It may result in serious health complications.
• Use a sturdy stool or ladder when you clean, maintain or repair the air conditioner at a height. Failure
to do so may result in serious injury or product failure.
• Do not mix the batteries for the remote control with other types of batteries or mix new batteries
with used batteries. Failure to do so may result in product failure.
• Do not recharge or disassemble the batteries. Failure to do so may result in explosion, fire or serious
injury.
• Stop using the remote control if there is a battery fluid leak. If your cloth or skin is exposed to the
battery fluid from a leak, wash it off with clean water. Failure to do so may result in serious injury.
• If you swallow the battery fluid from a leak, wash out the inside of your mouth thoroughly and then
consult a doctor. Failure to do so may result in serious health complications.
ENGLISH
! CAUTION
Installation
6
TABLE OF CONTENTS
ENGLISH
TABLE OF CONTENTS
2
3
TIPS FOR SAVING
ENERGY
13 ADVANCED FUNCTIONS
13
Operating the air conditioner without
the remote control
13
Restarting the air conditioner
automatically
IMPORTANT SAFETY
INSTRUCTIONS
14 MAINTENANCE
7
BEFORE USE
7
Components
8
Using the remote control
10 BASIC FUNCTIONS
10
Cooling your room
10
Heating your room
10
Removing humidity
11
Airing your room
11
Adjusting the fan speed
11
Adjusting the air flowdirection
11
Auto mode
12
Turning on the air conditioner automatically at a set time
12
Turning off the air conditioner automatically at a set time
12
Setting sleep mode
15
Cleaning the Air filter
16 TROUBLESHOOTING
16
Self-diagnosis function
16
Before requesting service
17
Operation ranges
BEFORE USE
7
ENGLISH
BEFORE USE
Components
Indoor unit
Air inlet
Reset switch
Front grille
Air filter
Vertical louver & Horizontal vane
Air outlet
* Please keep the protective film of reset switch. It is used to protect the PCB from ESD damage.
* The feature can be changed according to type of model.
!
NOTE
The number of operation lamps and their locations may vary, depending on the model of the
air conditioner.
Outdoor unit
Air inlet vents
Air outlet vents
Base plate
* The feature can be changed according to type of model.
Connection
wire
Coolant piping
Drain hose
8
BEFORE USE
ENGLISH
Using the remote control
You can operate the air conditioner more conveniently with the remote control. You will find the
buttons for the additional functions under the cover of the remote control.
Wireless remote control
Control Display
panel
screen
C
h
Sleep mode auto button*: SLEEP indicator
Display
screen
Control
panel
Description
Temperature adjustment buttons:
Increase the temperature or time by 1
unit, Decrease the temperature or time
by 1 unit
-
reset witch: Turns the power on/off.
Indoor fan speed button:
LOW FAN SPEED indicator,
MIDDLE FAN SPEED indicator,
HIGH FAN SPEED indicator.
AUTO FAN SPEED indicator.
Operation mode selection button*: Selects the operation mode.
AUTO mode indicator ( ) / COOLING
indicator ( ) / DEHUMIDIFYING indicator ( ) / FAN ONLY OPERATION indicator ( ) / HEATING indicator ( )
Air flow direction button:
FLAP SWING indicator
To set automatic switching-on/off
* Some functions may not be supported, depending on the
model.
BEFORE USE
Insert batteries before using the remote
control. The battery type used is AAA (1.5 V)
1 Remove the battery cover.
2 Fix the holder by fastening the 2 screws
firmly with a screwdriver.
Type “B” screw
3 Slide the remote control into the holder.
2 Insert the new batteries and make sure
that the + and - terminals of the batteries
are installed correctly.
Operating method
3 Reattach the battery cover.
!
Point the remote control towards the signal
receiver at the air conditioner to operate it
NOTE
If the display screen of the remote control
starts to fade, replace the batteries.
Installing the remote control holder
Install the holder where there is no direct sunlight to protect the remote control.
1 Choose a safe and easily-accessible place.
!
NOTE
• The remote control may operate other
electronic devices if pointed towards
them. Make sure to point the remote
control towards the signal receiver of
the air conditioner.
• For proper operation, use a soft cloth to
clean the signal transmitter and receiver.
ENGLISH
Inserting batteries
9
10 BASIC FUNCTIONS
ENGLISH
BASIC FUNCTIONS
Cooling your room
Removing humidity
(Cooling operation)
(Dehumidifying operation)
1 Press
2 Press
This mode removes excess moisture from an
environment with high humidity or in the rainy
season, in order to prevent mold from setting
in. This mode adjusts the room temperature
and the fan speed automatically to maintain
the optimal level of humidity.
1 Press
to turn on the power.
2 Press
repeatedly to select the dehumidifying operation.
is displayed on the display screen.
to turn on the power.
repeatedly to select the cooling
operation.
is displayed on the display screen.
3 Press
or
to set the desired temperature.
- The temperature range is 18°C (64°F) ~
31°C (88°F)
Heating your room
(Heating operation)
1 Press
2 Press
to turn on the power.
repeatedly to select the heating operation.
is displayed on the display screen.
3 Press
or
to set the desired temperature.
- The temperature range is 16°C(60.8°F)
~ 31°C (88°F)
* In this mode,horizontal vane repeatedly
can be opened and closed according to
outdoor temperature
!
NOTE
Cooling-only models do not support this
function.
!
NOTE
• In this mode you cannot adjust the desired temperature, as it is adjusted automatically. Also, the desired temperature
is not displayed on the display screen.
BASIC FUNCTIONS
(Air Circulation operation)
This mode only circulates the indoor air
without changing the room temperature.
1 Press
to turn on the power.
2 Press
repeatedly to select the air circulation operation.
is displayed on the display screen.
3 Press
to adjust the fan speed.
* In this mode, can’t use auto fan speed
Adjusting the air flow
direction
To adjust the direction of the air flow horizontally, press
repeatedly and select the desired direction.
- Select
to adjust the direction of the air
flow automatically.
!
NOTE
• Adjusting the air flow direction vertically
may not be supported, depending on
the model.
• Adjusting the air deflector arbitrarily may
cause product failure.
• If you restart the air conditioner, it starts
to operate with the previously set direction of air flow, so the air deflector may
not match the icon displayed on the remote control. When this occurs, press
to adjust the direction of the air
flow again.
Adjusting the fan speed
Press
repeatedly to adjust the fan speed.
- Select
if you want natural air.
The fan speed adjusts automatically.
Remark
Speed
High
Auto mode
(Change temperature automatically)
1 Press
2 Press
to turn on the power.
repeatedly to select auto mode
is displayed on the display screen.
-
Medium
C
h
Low
Auto
!
NOTE
In the auto mode, the temperature are
set automatically according to the room
temperature.
ENGLISH
Airing your room
11
12 BASIC FUNCTIONS
ENGLISH
Turning on the air conditioner
automatically at a set time
Turning off the air conditioner
automatically at a set time
To activate the time on, the air conditioner
should be off.
1 Press
.
- The
below flickers at the bottom of
the display screen.
To activate the time off, the air conditioner
should be on.
1 Press
.
2 Press
.
- The
below flickers at the bottom of
the display screen.
C
2 Press
3 Press
to select the mode
or
to select the temparature
(in Cool, Heat Mode).
4 Press
to select the wind speed (in
Auto, Cool, Fan, Heat Mode.)
5 Press
.
3 Press
4 Press
or
.
to select the minutes.
Setting sleep mode
Use the sleep mode to turn off the air conditioner automatically when you go to sleep.
1 Press
to turn on the power.
2 Press
6 Press
7 Press
or
.
to select the minutes
!
NOTE
In cooling or auto mode , the set temperature will automatically raise by1 every 60
minutes, to achieve a total rise of 2 during
the first 2 hours of work.
In heating mode the set temperature is
gradually decreased by 2 during the first 2
hours of work.
After 10 hours running in sleep mode the
air conditioner is swicthed off automatically.
ADVANCED FUNCTIONS 13
ENGLISH
ADVANCED FUNCTIONS
The air conditioner offers some additional advanced functions.
Restarting the air conditioner
automatically
Operating the air conditioner
without the remote control
When the air conditioner is turned on again
after a power failure, this function restores
the previous settings. This function is a factory default setting.
You can use the reset switch of the indoor
unit to operate the air conditioner when the
remote control is unavailable. However, the
fan speed is set to high.
1 Open the front cover.
- Lift up both sides of the cover slightly.
Disabling auto restart
1 Open the front cover.
- Lift up both sides of the cover slightly.
* The feature can be changed according to
type of model.
* The feature can be changed according to
type of model.
2 Press the reset switch.
2 Press the reset switch and hold it for 10
seconds. (9k, 12k)
- The unit will beep 4 and the lamp will
blink 1 times.
9k, 12k
Emergency
button
9k, 12k
display PCB
The emergency button in some models could
be on the right part of the unit under the front
panel. (18k, 24k)
* The feature can be changed according to
type of model.
Emergency
button
display PCB
The emergency button in some models could
be on the right part of the unit under the front
panel. (18k, 24k)
* The feature can be changed according to
type of model.
- To re-enable the function, press the reset
switch and hold it for 10 seconds. The unit will
beep 3 times and the lamp will blink 1 times.
14 MAINTENANCE
ENGLISH
MAINTENANCE
Clean the product regularly to maintain optimal performance and to prevent possible breakdown.
* This may not be provided, depending on the model.
Air filter
* The feature can be changed according to type of model.
Item
Air filter
Indoor unit surface
Outdoor unit
Cleaning interval
Cleaning method
2 weeks
See “Cleaning the Air filter.”
Use a soft, dry cloth. Do not use bleach or
Regularly
abrasives.
Use steam to clean the heat exchanger coils
Regularly
and the panel vents (consult with technician).
! CAUTION
• Turn off the power and unplug the power cord before you perform any maintenance; otherwise it may cause electric shock.
• Never use water that is hotter than 40°C when you clean the filters. It may cause deformation or discoloration.
• Never use volatile substances when you clean the filters. They may damage the surface of
the product.
!
NOTE
• The location and shape of the filters may differ, depending on the model.
• Make sure to clean the heat exchanger coils of the outdoor unit regularly, as dirt collected
in the coils may decrease the operational efficiency or increase energy costs.
MAINTENANCE 15
Clean the Air filter once every 2 weeks or
more if necessary.
1 Turn off the power and unplug the power
cord.
2 Open the front cover.
- Lift up both sides of the cover slightly.
* The feature can be changed according to
type of model.
3 Hold the knob of the Air filter, lift it up
slightly and remove it from the unit.
* The feature can be changed according to
type of model.
4 Clean the filter with a vacuum cleaner or
with warm water.
- If dirt is difficult to remove, wash the filter in lukewarm water with detergent.
5 Dry the filter in the shade.
ENGLISH
Cleaning the Air filter
16 TROUBLESHOOTING
ENGLISH
TROUBLESHOOTING
Self-diagnosis function
In case of error, the display on the indoor unit shown the folloing error codes:
Code
RUN lamp
E1
Flashes once
The fault of indoor temperature sensor
Description of the trouble
E2
Flashes twice
The fault of indoor pipe temperature sensor
E6
Flashes 6 times
Malfunction of indoor fan motor
Before requesting service
Please check the following before you contact the service center. If the problem persists, contact
your local service center.
Problem
Possible causes
Corrective action
-
Turn off the air conditioner, unplug the
power cord and contact the service center.
The air conditioner is
unplugged.
Check whether the power cord is plugged
into the outlet.
There is a burning smell and
a strange sound coming
from the unit.
Water leaks from the indoor
unit even when the humidity
level is low.
The power cord is damaged
or generating excessive
heat.
A switch, a circuit breaker
(safety, ground) or a fuse is
not operated properly.
A fuse is blown or the
Replace the fuse or check if the circuit
power supply is
breaker has tripped.
blocked.
The air conditioner does not A power failure has
work.
occurred.
The voltage is too
high or too low.
Turn off the air conditioner when a power
failure occurs. When the power is restored,
wait 3 minutes, and then turn on the air
conditioner.
Check if the circuit breaker has tripped.
The air conditioner
turned off automati- Press the power button again.
cally at a preset time.
TROUBLESHOOTING 17
Possible causes
Corrective action
Air is not circulating
properly.
Make sure that there are no curtains,
blinds or furniture blocking the front of the
air conditioner.
The Air filter is dirty.
Clean the air filter once every 2 weeks.
See “Cleaning Air filter” for more information.
Cold air is escaping
from the room.
Make sure that no cold air is escaping
through ventilation points in the room.
The air conditioner does not
The desired temperagenerate cool air.
Set the desired temperature to a level
ture is higher than the
lower than the current temperature.
set temperature.
There is a heating
source nearby.
Avoid using a heat generator such as an
electric oven or a gas burner while the air
conditioner is in operation.
Air circulation operation is selected.
In the air circulation operation, air blows
from the air conditioner without cooling or
heating the indoor air. Switch the operation mode to the cooling operation.
It is not possible to adjust
the fan speed.
In some operation modes, such as the jet
The auto operation,
or dehumidifying operation modes, you
jet operation or dehucannot adjust the fan speed. Select an opmidifying operation is
eration mode in which you can adjust the
selected.
fan speed.
It is not possible to adjust
the temperature.
In some operation modes, such as the air
The air circulation op- circulation or jet operation mode, you caneration or jet operanot adjust the temperature. Select an option is selected.
eration mode in which you can adjust the
temperature.
Operation ranges
For Heat & Cool model, heating operation range follows the below table.
Heating
operation range
outdoor temperature
0 ~ 24°C
* When the outdoor temperature drops below 0°C, heating capacity may drop slightly depending
on the operation condition.
ENGLISH
Problem
Download PDF