LG | MT-50PM10 | LG MT-50PM10 Owner’s Manual

PLASMA MONITOR
OWNER'S MANUAL
Please read this manual
carefully
before
operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
on
the back
mation to your dealer when you
Model number
:
Serial number
:
P/NO
:
3828VA0513A
(RF04GA,
cover
and
quote this infor-
require service.
138D
TX, 026H)
f
Safety Warnings
Instructions
Safety
Safety
Use the set at the
-
place
lower than the altitude of 6562 feet
(2000m)
get the best quality
to
of
picture and
sound.
W
WARNING
Do not
place the
sources
such
This may
-
Do not
or
any
registers,
sunlight
or
stove and
near
heat
so on.
damp place such as
likely to get wet.
bathroom
a
fire
could
or
give
an
In
-
Bend
cable
antenna
building
to
prevent
rain from
This may cause water
electric shock.
-
between
damaged
inside
flowing
case
and
cleaning the
damaged
cause
of smoke
or
the set
strange smell
set.
could
or
give
from the
an
electric
set, switch
from the wall outlet and contact your
service center.
,unplug it
dealer
electric shock.
water while
use
This may
shock.
it off
where it is
cause a
Do not
-
fire.
the set in
place
This may
-
cause a
use
set in direct
heat
as
or
This may
cause a
fire
or
could
give
an
electric shock.
outside
Do not
in.
inside the set and could
give
an
attempt
your dealer
-
This may
shock.
or
to service the set
yourself. Contact
service center.
cause
damaged
the set
or
could
give
an
electric
Earth wire should be connected.
If the earth wire is not connected, there is possible
by the current leakage.
-
a
danger
of
electric shock caused
If
-
grounding
er
should be
methods
are
employed
not
During
a
lightning thunder, unplug the
wall outlet and don't touch
possible, a separate circuit breakby a qualified electrician.
and installed
-
This may
shock.
cause
damaged
an
set from the
antenna cable.
the set
or
could
give
an
electric
Power
supplier
Short-circuit
breaker
Do not connect
-
ground to telephone wires, lightning
rods
or
gas
pipe.
Do not
place anything containing liquid
on
top
of the
set.
-
This may
cause a
Do not insert any
-
This may
Do not
-
cause a
fire
or
could
cause
an
or
could
serious
injury
give
on
to
a
an
2
This set is
vent.
electric shock.
the set.
child
WARNING in U.K.
*
electric shock.
object into the exhaust
fire
place heavy objects
This may
give
or
adult.
only
with a BS 1363 approved 13 amp mains plug, fused at 13 amp. When replacing the fuse
always use a 13 amp BS 1362, BSI or ASTA approved type. Never use this plug with the fuse cover omitted. To
obtain a replacement fuse cover contact your dealer or "LG Electronics U.K. Ltd." If the type of plug supplied is not
suitable for the mains sockets in your home, then the plug should be removed and a suitable type fitted.
A mains plug removed from the mains lead of this set must be destroyed. A mains plug with bared wires is
hazardous if inserted in a mains socket. Do not connect either wire to the earth pin, marked with the letter E or
with the earth symbol
or coloured green or green and yellow. If any other plug is fitted, use a 13 amp fuse,
either in the plug, or at the distribution board.
The wires in this mains lead are coloured in accordance with the following codes: BLUE: NEUTRAL, BROWN: LIVE
As the colours of the wires in the mains lead of this set may not correspond with the coloured marking identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected
to the terminal which is marked with the letter L or coloured red.
supplied
PLASMA MONITOR
Safety Warnings
*
Safety
instructions have two kinds of
information, and each meaning of it is
as
The violation of this instruction may cause serious
WARNING
The violation of this instruction may cause
NOTES
product.
Take
care
of
below.
injuries
light injuries
and
even
damage
or
death.
of the
danger that may happen under specific condition.
NOTES
Never touch the power
-
This may
cause an
plug with
wet hand.
a
Ensure the power cord doesn't trail
like a heater.
electric shock.
-
Disconnect from the mains and
tions before
remove
all
Do not
This may
Do not
moving.
place the
set in
a
built-in installation such
as a
-
Ventilation
cause a
fire
or an
electric shock.
plug
or
the
when the power cord or the plug is damconnecting part of the power outlet is
loose.
-
or
any hot
connec-
aged
bookcase
across
objects
rack.
This may
cause a
fire
or an
electric shock.
required.
Dispose of used batteries carefully
eating them.
to
protect
a
child
from
-
In
case
When
carry
-
When
installing the set on
place the edge of its stand.
-
a
table, be careful
not to
injury to
child
a
see a
doctor
immediately.
moving the set assembled with speakers do
holding the speakers.
This may cause the set to fall, causing serious
adult, and serious damage to the Monitor.
injury to
a
not
child
or
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
-
This may cause the set to fall, causing serious
adult, and serious damage to the set.
that it eats them, take it to
This may
cause
damaged
the set
or
could
give
an
electric shock.
or
Contact the service center
internal
-
part
once
a
year to clean the
of the set.
Accumulated dust
can cause
mechanical failure.
The distance between eyes and the screen should be
7 times as long as diagonal length of the
about 5
~
screen.
-
If not, eyes will strain.
Unplug the
long periods
Accumulated dust may
deterioration or electric
fire
-
Do not
place
an
outside antenna in the
head power lines
cuits.
-
This may
cause an
There should be
or
other electric
of
vicinity
light or power cirover-
set from the wall outlet when it is left unat-
tended and unused for
cause a
or an
of time.
electric shock from
leakage.
electric shock.
enough distance between
an
outside
power lines to keep the former from
the latter even when the antenna falls.
antenna and
touching
-
This may
Do not
-
cause an
electric shock.
pull the cord but the plug
This may
cause a
when
unplugging.
fire.
Owner's Manual
3
Contents
Contents
Contents
Special
Safety Warnings
SafetyInstructions.......................2~3
ISM
RemoteControlKeyFunctions................6
LocationandFunctionofControls
.
.
.
.
.
.
.
.
.
.
.7~9
Installation
External
Equipment Viewing Setups
Displayable Monitor Specification
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.10~11
.
.
.
.
.
.12
Accessories.............................13
InstallationOptions.......................14
TurningontheSet........................15
On-Screen Menu Language Selection (option)
.15
Picture Menu Options
PSM(PictureStatusMemory)...............16
.
.
..................................16
AdjustingAutoColourControl.
Manual Colour Temperature Control (User option)
sRGB (RGB[PC], DVI[PC] mode only)
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.16
.
.
.
.
.
.
.
.16
.17
.17
(User option)
Options
SSM(SoundStatusMemory)................18
.
.
.
.
.
.
.
.
BBE...................................18
AVL(AutoVolumeLeveler).................18
.18
Adjusting Sound Control (User option)
Time Menu Options
SettingtheClock.........................19
SettingtheOn/OffTimer...................19
AutoSleep..............................19
SleepTimer.............................19
.
this
manu-
where the
always
4
user can
contact
easily.
PLASMA MONITOR
.
.
.
.
.20
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
ScreenPosition..........................22
Manual Configure (RGB [PC] mode only)
.23
Selecting Wide VGA/XGA mode (RGB[PC] mode only) .23
ScreenAdjustments.......................23
.
.
.
.
.
.
.
.
.
Luminance Noise Reduction
.24
(option)
.24
Initializing (Reset to original factory value)
SplitZoom..............................24
PIP (Picture In Picture) Feature
WatchingPIP............................25
.25
Selecting an Input Signal Source for the PIP
.25
MovingthePIP(PIPmodeonly).
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PictureSize.............................25
Adjusting
PIP
mode
Transparency (PIP
only)
.
.
.
.25
.
Sound Menu
reading
.
Demo(option)......................21
.21
MenuRotationforVerticalViewing.
Screen Menu Options
Auto adjustment (RGB [PC] mode only)
.22
SettingPictureFormat.....................22
.
Fleshtone...............................17
al, keep it in the place
Method
(Image Sticking Minimization)
Cinema................................23
Operation
After
Options
LowPower..............................21
Introduction
Manual Picture Control
Menu
ChildLock..............................20
.
Miscellaneous
.26~31
ExternalControlDeviceSetup
IRCode(NECformat)..................32~33
TroubleshootingChecklist..................34
ProductSpecifications.....................35
.
.
.
.
.
.
.
.
.
.
.
Introduction
Introduction
What is
a
Plasma
Display
?
If voltage is inputted to gas in glass panels, ultraviolet rays is outputted and fused with a fluorescent substance.
light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
160°
Wide
-
A Plasma
angle range
Display provides
At this moment,
of vision
than 160°
more
angle
range of vision
so
that you
can
get
without distortion from any
picture
a
direction.
Easy
installation
A Plasma
Display is
place.
much
lighter
and smaller than other
same
class
products
so
that you
can
install the Plasma
Display
at the desired
Big
screen
The
screen
of
a
Plasma
Multimedia Plasma
A Plasma
and
The
Display
can
Display
is 42"
(or 50")
so
that you
can
get vivid experience
if you
as
are
in
a
theater.
Display
be connected with
a
computer
so
that you
it
can use
as a screen
for
conference, game, internet
so on.
explanation
about coloured dots may be present
The PDP which is the
display
device of this
product
is
composed
in the manufacture of the PDP. Several coloured dots visible
on
on
PDP screen
of 0.9 to 2.2 million cells and
the
screen
would be
a
few cell defects
acceptable,
manufacturers and would not mean that the PDP is faulty. We hope you will understand that the product
sponds to this standard is regarded as acceptable. It means that it could not be changed or refunded.
We promise that we'll do our best to develop our technology to minimize the cell defects.
The
explanation
In the
same
about noise of 42"
way that
a
fan is used in
reliability of this product. Therefore,
any negative effect on its efficiency
a
a
(or 50")
PC to
keep
It
means
that it is not
which
corre-
PDP
the CPU
cool, the PDP is equipped with cooling fans
certain level of noise could
occur
to improve the
operated. This noise doesn't have
difficulty while using this product. The
when the fan is
and
liability and it's also determined to have no
operation of this product. We hope you will understand
changeable nor refundable.
noise from the fans is normal in the
acceptable.
can occur
in line with other PDP
that
a
certain level of noise is
TO AVOID BURNING IMAGE INTO THE DISPLAY, DO NOT HAVE A STILL IMAGE ON SCREEN FOR EXTENDED PERIOD
OF TIME. IMAGE AFTER BURN WILL NOT BE COVERED UNDER WARRANTY ie.Menus, Video games, Borders
or
LOGOS
WARNING
This is Class A
case
the
user
product. In a domestic environment this product
may be required to take adequate measures.
may
cause
radio interference in which
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
Owner's Manual
5
Introduction
Remote Control
Control
-
-
When
Functions
Key
using the remote control aim it at the remote control sensor of the set.
maybe a defect in consecutive operation of remote control in specified brightness according
There's
MUTE
off.
Switches the sound
Selects the
POWER
switches the set
off to standby.
on or
MULTIMEDIA
RGB or DVI
modes.
MUTE
input
mode for the sub
on
from
standby
or
POWER
Component,
INPUT SELECT
PIP INPUT
PIP INPUT
Selects the
to this set feature.
MULTIMEDIA INPUT SELECT
ARC
pic-
ture.
EXIT
ARC
Changes
MENU
the
format.
picture
EXIT
Clears all
on-screen
MENU
displays.
Displays
by
on screen menus one
one.
Exits the current menu.
Memorizes menu changes.
D/E
Selects
option.
(Volume Up/Down)
a menu
OK
F / G
Increases/decreases sound level.
Adjusts
menu
VOL
VOL
settings.
OK
accepts your selection
or
displays
the
NUMBER buttons
current mode.
123
SSM
To select the sound
456
your
PSM
Adjusts
7
viewing
appropriate
to
programme character.
89
the
factory preset picture
according to the room.
PSM
Enlarge
SPLIT ZOOM
the screen with regular
ration.
0
SSM
SPLIT ZOOM
PIP/DW
SLEEP
WIN. SIZE
POSITION
SWAP
SLEEP
Sets the
SCAN-
PLAY
SCAN+
SWAP
SKIP-
STOP
SKIP+
PAUSE
POWER
PIP/DW
Switches the sub picture on
Selects PIP or DW modes.
sleep
or
off.
timer.
WIN.SIZE
Adjusts
the sub
picture
size.
Alternates between main and sub
ture.
POSITION
MovesthesubpicturetoD/EorF/G
direction.
Installing
player.
Batteries
?
Open
the
battery compartment
insert the batteries with correct
?
PLASMA MONITOR
cover on
new
batteries.
the back side and
polarity.
Install two 1.5V alkaline batteries of AAA
batteries with
6
DVD BUTTONS
controls a LG DVD
type. Don't mix used
pic-
Introduction
Location and Function of
of Controls
Controls
-
-
Shown is
a
simplified representation
of the set.
Here shown may be somewhat different from your set.
<Front Panel Controls>
6
5
32
ON/OFF
4
1
or
INPUT SELECT
VOL
MENU
ON/OFF
1
23
4
1. Main Power Button
5
6
5. MENU
Displays
2. Remote Control Sensor
on screen menus one
Exits the current
Memorizes
menu
by
one.
menu.
changes.
3. Power
Standby Indicator
Illuminates red in standby mode,
set is turned
on
4. INPUT SELECT Button
Illuminates green when the
6.D/E
Selects
a menu
option.
F / G (Volume Up/Down)
Increases/decreases sound level.
Adjusts
menu
settings.
Owner's Manual
7
Introduction
Location and Function of
of Controls
Controls
<Back Panel>
R
REMOTE
RS-232C INPUT
CONTROL
(CONTRO SERVICE)
DVI
PUT
AUDIO NPUT
RGB
PUT
RGB
UTPUT
YB
PR
Connection to PC
8
AC INPUT
RL (
COMPON NT INPUT
PLASMA MONITOR
L
RL
AUDIO NPUT
S-V
DEO
AUDIO INPUT
ONO)
VIDEO INPUT
Connection to AV
EXTERNAL SPEAKER
equipment
Introduction
<Back Panel>
RCA
Type
R
L
YP BPR
(MONO)
12
Scart
3
5
4
6
Type
R
L
YP BPR
5
1. CONTROL LOCK / REMOTE CONTROL
2.
RS-232C
INPUT(CONTROL/SERVICE)
Connect to the RS-232C
port
on a
5.
COMPONENT / AUDIO INPUT SOCKETS
S-VIDEO / AUDIO
PORT
VIDEO / AUDIO
PC.
(L/MONO) INPUT SOCKETS
(L/MONO) INPUT SOCKETS
EURO SCART SOCKET
3.
DVI INPUT / AUDIO INPUT / RGB INPUT SOCKETS
Connect the monitor
output socket of the PERSONAL COM-
Note: If you want to use your external hi-fi stereo system,
turn off the internal speakers of the set.
PUTER to this socket.
RGB OUTPUT SOCKET
You
can
watch the RGB
RGB OUTPUT to
6.
another
monitor,
another monitor's PC input port.
signal
on
connect
POWER CORD SOCKET
This Monitor
operates
cated
Specifications
on
the
the Monitor
4.
on
AC power. The voltage is indipage. Never attempt to operate
on an
DC power.
EXTERNAL SPEAKER OUTPUT
(8 ohm)
Connect to optional external speaker(s).
For further information, refer to 'Speaker & Speaker
*
Stand'
manual.
Owner's Manual
9
Installation
External
VCR (When the Interface board is installed.)
Watching
-
V iewing Setups
Equipment Viewing
Setups
When
connecting the Plasma Monitor with
Audio(L) white, Audio(R) -red).
Connect the VIDEO INPUT socket(yellow)
external
equipments,
match the colours of
connecting ports (Video
-
yellow,
-
-
-
-
-
with the BNC-RCA adapter to the VIDEO INPUT socket of the set.
If you have a mono VCR, connect the audio cable from the VCR to the AUDIO(L/MONO) input of the Plasma Monitor.
If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input.
Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set.
Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still
4:3 picture format or if a CH label is present; the fixed image may remain visible on the screen.
Use the orbiter function to avoid having a fixed image. (Refer to p.20)
1. Press INPUT SELECT button on the remote control and select AV or (AV 1 or AV 2 ).
(When connecting with S-Video, select the S-Video.)
2. Insert a video tape into the VCR and press the PLAY button on the VCR. (See VCR
Watching
-
After
from
a
VCR,
manual)
Cable TV (When the Interface board is installed.)
subscribing
to
a
cable TV service from
This monitor cannot
ming.
owner 's
picture
display
TV
a
local
programming
and
provider
without
a
installing
a
can watch cable TV programcable TV converter box connected to the
converter, you
TV tuner device
or
monitor.
1. Press INPUT SELECT button on the remote control and select AV
2. Tune to cable service provided channels using the cable box.
Watching
-
-
When
Or,
external AV
connecting
source
or
(AV 1
or
AV 2 ).
(When the Interface board is installed.)
the Plasma Monitor with external
equipments,
match the colours of
connect the Euro scart socket of the VCR to the Euro scart socket of the set.
connecting ports.
1. Press INPUT SELECT button on the remote control of the monitor to select AV or (AV 1 or AV 2 ).
2. Operate the corresponding external equipment. (See external equipment operating guide.)
Watching
DVD (When the Interface board is installed.)
How to connect
Connect DVD video
-
INPUT)
-
Or,
and audio
inputs
inputs
to
Y, PB, PR of COMPONENT (DVD
to Audio sockets of AUDIO INPUT.
connect the Euro scart socket of the VCR to the Euro scart socket
?
Component Input ports
You can get better picture quality if you connect DVD player with component input ports
as
below.
Component ports
of the
Monitor
YPBPR
of the set.
How to
use
1. Press INPUT SELECT button
select
2.
on
the remote control of the monitor to
Component or (AV 1 or AV 2 ).
Try this after turning on the DVD player.
(Refer to the DVD player's manual for operating instructions.)
10
PLASMA MONITOR
Video
output ports
of DVD
player
Y
Y
Y
Y
Pb
B-Y
Cb
PB
Pr
R-Y
Cr
PR
Installation
DTV
Watching
-
To watch
top
?
broadcast programs,
digitally
purchase/connect
a
digital
set-
box.
How to connect
-
Setup (option)
Connect
a
DTV
user-supplied Digital Set-Top
set-top box video output
to
Box
DTV
Input signal
Mode
Terminal
Component
RGB
(DTV)
DVI
(DTV)
480p (60Hz)
o
o
o
576p (50Hz)
o
o
o
720p
o
o
o
1080i
o
o
o
monitor COMPONENT
(DVD/DTV INPUT) or to the monitor RGB (PC/DTV INPUT) or to the
monitor DVI (PC/DTV INPUT) connector depending on your set-top
box connectors.
-
Connect DTV
set-top box audio outputs
to monitor AUDIO
INPUT
jacks.
How to
1. Turn
use
the a digital set-top
digital set-top box)
on
2. Use INPUT SELECT
RGB
or
-
-
-
-
(Refer
to the owner's manual for the
the remote control to select
Component,
DVI.
Connecting
-
on
box.
PC
To
enjoy vivid picture and sound, connect a PC to the set.
Avoid keeping a fixed image on the set's screen for a long period of time. The fixed image may become permanently imprinted on
the screen; use a screen saver when possible.
Connect PC to the RGB INPUT(PC INPUT) or DVI INPUT(DIGITAL RGB INPUT) port of the set; change the resolution output of
PC accordingly.
There might be a noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Then change the PC
mode into other resolution or change the refresh rate into other rate or adjust the brightness and contrast on the menu until the
picture is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to the
manufacturer of the PC graphic card.
The synchronization input form for Horizontal and Vertical frequencies is separate.
Setup Instructions to Connect a PC to your set
We recommend using 1024x768, 60Hz for the PC mode, they provide the best picture quality.
In MT/MZ-42PM10/11/20/21 series, we recommend using 640x480, 60Hz for the PC mode, they provide the best picture quality.
If the resolution of PC is over UXGA, there will be no picture on the set.
Connect the signal cable from the monitor output port of the PC to the RGB INPUT port of the set or the signal cable from the DVI
-
-
-
output port of the PC
-
-
-
-
-
-
-
to the DVI INPUT
port
on
the set.
Connect the audio cable from the PC to the Audio
If
using
a
sound
input on the set. (Audio
required.
Play Solution. The set provides EDID data
card, adjust PC sound
This set
cables
are
not included with the
set).
as
to the PC system with a DDC protocol. The PC adjusts
apply a VESA Plug and
automatically to use this set.
DDC protocol is preset for RGB (Analog RGB), DVI (Digital RGB) mode.
If required, adjust the set settings for Plug and Play functionally.
If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB INPUT or DVI
INPUT to display the PC on the set.
If graphic card on the PC does output analog and digital RGB simultaneously, set the set to either RGB or DVI; (the other mode
is set to Plug and Play automatically by the set.)
DOS mode may not work depending on video card if using a DVI-I cable.
PC
Setup
1. Turn
on
the PC and
2. Turn
on
the
apply power to
display by pressing the
3. Use the INPUT SELECT
4. Set the resolution
or
the set.
POWER button
MULTIMEDIA button
output of the PC
to SXGA
or
on
on
the set's remote control.
the remote control to select the RGB
under
(1280
x
1024, 60Hz). (Refer
to p.
or
DVI
input
source.
12)
Owner's Manual
11
Installation
Displayable
Monitor
Specification
Specification
RGB / DVI mode
Resolution
RGB / DVI mode
Horizontal
Vertical
Frequency(KHz)
Frequency(Hz)
31.468
70.09
31.468
70.09
37.861
85.08
37.861
85.08
31.469
70.08
31.469
70.08
37.927
85.03
37.927
85.03
31.469
59.94
31.469
59.94
35.000
66.66
35.000
66.66
37.861
72.80
37.861
72.80
37.500
75.00
37.500
75.00
43.269
85.00
43.269
85.00
31.500
60.00
31.500
60.00
37.799
70.00
37.799
70.00
39.375
75.00
39.375
75.00
31.500
60.00
31.500
60.00
37.799
70.00
37.799
70.00
39.375
75.00
39.375
35.156
56.25
35.156
37.879
60.31
37.879
60.31
48.077
72.18
48.077
72.18
46.875
75.00
46.875
75.00
53.674
85.06
53.674
85.06
49.725
74.55
49.725
74.55
48.363
60.00
48.363
60.00
56.476
70.06
56.476
70.06
60.023
75.02
60.023
75.02
68.677
85.00
68.677
85.00
54.348
60.05
47.700
60.00
63.995
70.01
59.625
75.02
67.500
75.00
68.500
85.00
47.700
60.00
59.625
75.02
640x350
848x480
852x480
800x600
832x624
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
640x350
720x400
640x480
Resolution
720x400
1024x768
640x480
848x480
852x480
800x600
832x624
75.00
56.25
(RGB)
1024x768
1360x768
1152x864
77.487
85.00
1152x870
68.681
75.06
1280x960
60.023
60.02
69.500
85.00
1280x1024
63.981
60.02
54.348
60.05
63.995
70.01
67.500
75.00
77.487
85.00
68.681
75.06
47.693
60.00
60.091
75.00
68.504
85.00
1280x960
60.023
60.02
1280x1024
63.981
60.02
MT/MZ-42PM10/11/20/21 series
1366x768
1152x864
1152x870
1280x768
MT/MZ-42PM12X series
MT/MZ-50PM10/11/20/21 series
12
PLASMA MONITOR
Installation
Accessories
MUTE
PIPINPUT
EXIT
POWER
MULTIMEDIA INPUTSELECT
ARC
MENU
OK
VOL
VOL
123
456
7
PSM
LG TV
1.5V
Owner's Manual
Alkaline batteries
-
SSM
POSITION
SWAP
SCAN-
PLAY
SCAN+
SKIP-
STOP
SLEEP
SKIP+
PAUSE
POWER
Remote Control handset
BNC-RCA
adapter
(optional)
Power Cord
Optional
0
PIP/DW
WIN. SIZE
1.5V
ASmark
89
SPLIT ZOOM
Extras
Optional
extras
can
be
changed
or
modified for
quality improvement
without any notification
new
optional
extras
can
be
added.
-
Contract your dealer for
buying
50
42
these items.
40
40
42
50
42
40
40
50
Tilt wall
mounting
42
bracket
Ceiling mounting
Desktop
stand
bracket
Speakers
Owner's Manual
13
Installation
Installation
?
?
?
The set
can
Options
Options
be installed in different ways such as on a wall, or on a desktop etc.
only in a location where adequate ventilation is available.
Install this set
This set is
designed
so
that it
be mounted either
can
Wall Mount: Horizontal Installation
?
The set
further
can
be installed
information, refer
Bracket Installation and
?
Speakers
Desktop
are
optional,
on a
wall
as
shown above.
optional
Setup Guide'.)
are
or
vertically.
Wall Mount: Vertical Installation
to the
and
horizontally
'Wall
(For
Mounting
shown for illustration
?
The monitor
can be installed vertically on the wall as
above.(For further information, refer to the
optional 'Wall Mounting Bracket Installation and Setup
Guide'.)
Caution: When installing the monitor vertically, the
front panel controls must be in the left-down side posi-
shown
only.
tion
Pedestal Installation
?
?
as
shown above.
Speakers
only.
Note: To
source's
?
The set
(For
?
can
further
be mounted
on a
information, refer
desk
as
use
and
the Monitor in
image
are
a
shown for illustration
vertical
must also be in
a
orientation, the
vertical format.
shown above.
to the
optional 'Desktop
Stand Installation and Setup Guide'.)
Speakers and speaker stands shown are optional, and
are shown for example only.
To Mount
on a
Wall
To Install
on a
Desktop
Wall mount minimum allowable clearances for ade-
Pedestal mount minimum allowable clearances for
quate ventilation.
adequate
10cm
3cm
10cm
10cm
10cm
14
optional,
are
PLASMA MONITOR
ventilation.
Operation
Turning
Turning
-
When
using
Turning
on
the remote
the set
just
1. Connect power cord
2. Press the
the Set
Set
on
on
control, aim it
on
on
1. If the set
?
was
Press the
2. If the set
?
the set
the set
on
or
Press the
the set. At this moment, the set is switched to
press the
(power cord
is still
turned off with the
ON/OFF button
or
on
ON/OFF button
the set to turn the set
menus can
on
3. Press the
From this
be shown
on
on
the remote control
the set
ON/OFF button
on
the set
on
the set
or
press the
POWER,
on
the
screen
Selection (option)
Language Selection
(option)
in the selected
/
use
language.
First select your
button to select the SPECIAL
language.
menu.
button and then
use
/
button to select
button and then
use
/
button to select your desired language.
will be shown in the language of your choice.
point
mode. Press the INPUT
on.
the set and then press the INPUT SELECT button
on the remote control to turn the set on.
1. Press the MENU button and then
2. Press the
standby
MULTIMEDIA button
MULTIMEDIA button
On-Screen
On-Screen Menu
The
or
connected)
turned off with the remote control and the
INPUT SELECT
-
POWER, INPUT SELECT
on.
ON/OFF button
was
the set.
correctly.
and then the set will switch
Turning
sensor on
after installation
ON/OFF button
SELECT button
at its
on, the
Language.
on-screen menus
4. Press the EXIT button to return to normal
viewing.
Owner's Manual
15
Operation
Picture Menu
PSM
-
-
(Picture
Status
This function
Options
Options
Memory)
the set to the best
adjusts
picture appearance.
adjusting picture options (contrast, brightness, colour, sharpness
automatically changed to User.
When
is
and tint
(NTSC input only)) manually,
PSM
1. Press the PSM button
?
Each press of the PSM button
changes
You
?
Picture
the
-
-
You
can
screen
display
shown below.
as
Mild
Standard
Dynamic
?
the
also select Dynamic, Standard, Mild
options Dynamic, Standard
factory and cannot be changed.
and Mild
or
are
User in the PICTURE
User
menu.
preset and programmed for good picture quality
at
enjoy the vivid and hi-definition picture with LG's excellent Digital Reality processor technology.
selecting picture options (Dynamic, Standard and Mild) in PICTURE menu, XD is automatically changed
can
When
to On.
1. Press the MENU button and then
use
button to select the PICTURE
/
menu.
PICTURE
PSM
2. Press the
button and then
use
/
On
button to select XD.
Off
CSM
Fleshtone
3. Press the
button and then
use
button to select On
/
4. Press the EXIT button to return to normal
Off.
or
Contrast
viewing.
100
Brightness
60
Colour
50
Sharpness
50
Menu Prev.
Adjusting
-
Auto Colour Control
To initialize values
(reset
to default
settings),
1. Press the MENU button and then
use
select the Normal
option.
button to select the PICTURE
/
menu.
PICTURE
PSM
2. Press the
button and then
use
/
button to select CSM.
3. Press the
button and then
use
/
button to select the desired colour
Cool
CSM
Fleshtone
tempera-
ture.
4. Press the EXIT button to return to normal
?
Each press of
/
button
Cool
Manual Colour
-
You
can
changes
the
Temperature
green,
or
screen
display
Brightness
60
Colour
50
Sharpness
50
shown below.
Warm
User
Red
-10
Green
0
Blue
10
Menu Prev.
User
(User option)
blue to any colour
1. Press the MENU button and then
as
Warm
Control
Normal
100
viewing.
Normal
adjust red,
Contrast
use
temperature you prefer.
button to select the PICTURE
/
menu.
PICTURE
PSM
2. Press the
button and then
use
/
button to select CSM.
3. Press the
button and then
use
/
button to select User.
Cool
CSM
Fleshtone
4. Press the
?
The
button and then
adjustment
use
/
/
button to make
appropriate adjustments.
PLASMA MONITOR
viewing.
Normal
100
Brightness
60
Colour
50
Sharpness
50
range of Red, Green and Blue is -30~+30.
5. Press the EXIT button to return to normal
16
/
Contrast
Menu Prev.
Warm
User
Red
-10
Green
0
Blue
10
Operation
sRGB
-
(RGB[PC], DVI[PC]
When the set
the
was
equal image
mode
only)
connected to external
equipment
with sRGB
function, It's adjusted
a
colour difference to
display
each other.
1. Press the MENU button and then
use
button to select the PICTURE
/
menu.
PICTURE
PSM
2. Press the
button and then
use
/
button to select sRGB.
3. Press the
button and then
use
/
button to select On
CSM
sRGB
4. Press the EXIT button to return to normal
or
Off.
On
Contrast
viewing.
100
Brightness
60
Colour
50
Off
Prev.
Menu
Fleshtone
-
-
Adjust the Fleshtone to select the desired skin colour option.
This function works in the following mode:
AV (or AV1, AV2), COMPONENT 480i/480p/576i/576p/720p/1080i.
1. Press the MENU button and then
use
button to select the PICTURE
/
menu.
PICTURE
PSM
2. Press the
button and then
3. Press the
button and then
?
The
adjustment
use
use
/
/
button to select Fleshtone.
button to make
range of Fleshtone is 0
4. Press the EXIT button to return to normal
CSM
appropriate adjustments.
3.
~
Fleshtone
Contrast
60
Colour
50
Sharpness
50
viewing.
Menu
Manual Picture Control
-
-
You
Prev.
(User option)
adjust picture contrast, brightness, colour, sharpness
broadcasting system PAL/SECAM, the picture item Tint
can
In the
0
100
Brightness
1. Press the MENU button and then
use
/
and tint
(NTSC input only)
to the levels you
prefer.
doesn't work.
button to select the PICTURE
menu.
PICTURE
PSM
2. Press the
button and then
use
/
3. Press the
button and then
use
/
button to select the desired
button to make
4. Press the EXIT button to return to normal
viewing.
picture option.
appropriate adjustments.
CSM
sRGB
Contrast
100
Brightness
60
Colour
50
Sharpness
50
Menu
Prev.
Owner's Manual
17
Operation
Sound
Sound Menu
SSM
-
-
(Sound
Status
Options
Options
Memory)
This function lets you enjoy the best sound without any special adjustment because the set automatically selects the
appropriate sound option based on the program content.
When adjusting sound options (treble and bass) manually, SSM is automatically changed to User.
1. Press the SSM button.
2. Press the SSM button to select your desired sound.
Flat
SRS TSXT
Music
Movie
?
You
?
The sound SRS TSXT, Flat, Music, Movie and Speech
and cannot be changed.
can
also select SRS TSXT, Flat, Music, Movie, Speech
are
or
User
Speech
User in the SOUND
programmed
for
good
menu.
sound
reproduction
at the
factory
R
is
-
-
a
trademark of SRS
TruSurround XT
technology
is
Labs, Inc.
incorporated
under license from SRS
Labs, Inc.
BBE
-
BBE
High
Definition Sound restores
1. Press the MENU button and then
clarity
use
and presence for better
speech intelligibility
button to select the SOUND
/
and musical realism.
menu.
SOUND
SSM
2. Press the
button and then
use
BBE
button to select BBE.
/
On
Off
AVL
Balance
3. Press the
button and then
use
button to select On
/
4. Press the EXIT button to return to normal
-
(Auto
Volume
Off.
Treble
50
Bass
50
viewing.
Manufactured under license from BBE
AVL
or
0
Sound, Inc.
Menu Prev.
Leveler)
This feature maintains
an
equal
volume
1. Press the MENU button and then
level;
use
/
even
if you
change
channels.
button to select the SOUND
menu.
SOUND
SSM
2. Press the
button and then
use
/
button to select AV L
3. Press the
button and then
use
/
button to select On
BBE
.
AVL
On
Balance
4. Press the EXIT button to return to normal
or
Off.
0
Treble
50
Bass
50
viewing.
Menu Prev.
Adjusting
Sound Control
(User option)
1. Press the MENU button and then
use
/
button to select the SOUND
SOUND
menu.
SSM
2. Press the
button and then
use
/
button to select the desired sound item.
3. Press the
button and then
use
/
button to make
BBE
AVL
Balance
4. Press the EXIT button to return to normal
Note
18
:
Treble, Bass
or
BBE aren't suitable to
PLASMA MONITOR
appropriate adjustments.
Bass
viewing.
use
0
Treble
SRS TSXT.
Menu Prev.
50
Off
Operation
Time Menu Options
Options
Setting
-
the Clock
If current time
setting
is erased
by
a
power
failure, if the
set is
unplugged
or
turned off with the
ON/OFF button
the set, reset the clock.
on
1. Press the MENU button and then
use
button to select the TIME
/
menu.
TIME
Clock
2. Press the
button and then
use
/
button to select Clock.
3. Press the
button and then
use
/
button to
adjust
the hour.
4. Press the
button and then
use
/
button to
adjust
the minute.
-
-
-
--
sleep
viewing.
Menu
Setting
:
On time
Auto
5. Press the EXIT button to return to normal
--
Off time
Prev.
the On/Off Timer
Timer function
operates only if
Off Timer function overrides
The set must be in
standby
current time has been
Timer function if
on
they
set.
already
are
set to the
same
time.
mode for the On Timer to work.
1. Press the MENU button and then
use
button to select the TIME
/
menu.
TIME
Clock
2. Press the
button and then
use
/
button to select Off time
3. Press the
button and then
use
/
button to select On.
4. Press the
button and then
use
/
button to
adjust
the hour.
5. Press the
button and then
use
/
button to
adjust
the minute.
6.
Only On time
ume level.
function;
Press the
button and then
7. Press the EXIT button to return to normal
-
To cancel
Off/On
Press the
Auto
-
/
or
On time.
Off time
On time
On
Auto
Off
sleep
12
button to
/
use
:
Volume
vol-
adjust
Menu
00
1
Prev.
viewing.
time function
button to select Off in
step
3.
Sleep
If there is
no
input signal,
the monitor turn off
1. Press the MENU button and then
use
automatically
after 10 minutes.
button to select the TIME
/
menu.
TIME
Clock
2. Press the
button and then
use
/
button to select Auto sleep.
3. Press the
button and then
use
/
button to select On
Off time
On time
Auto
4. Press the EXIT button to return to normal
or
Off.
-
-
On
Off
viewing.
Menu
Sleep
sleep
Prev.
Timer
Sleep
timer turns the set off at the
preset time.
Press the SLEEP button to select the number of minutes. The
lowed
by
zz
display
begins
10, 20, 30, 60, 90, 120, 180 and 240 minutes. The timer
---
Min will appear
on
the screen, fol-
to count down from the number of minutes
selected.
a.
To check the
remaining sleep time, press the OK or SLEEP button once.
sleep time, repeatedly press the SLEEP button until the display
the set off after setting the sleep timer, the setting will be erased.
b. To cancel the
c.
If you turn
zz
---
Min appears.
Owner's Manual
19
Operation
Special
Special
Menu
Options
Options
Child lock
The set
-
be set up
can
so
that it
only
can
1. Press the MENU button and then
be used with the remote control.
button to select the SPECIAL
/
menu.
SPECIAL
Language
2. Press the
button and then
3. Press the
button and then
button to select Child lock.
/
button to select On
/
or
Child lock
On
ISM Method
Off
Low power
Off.
Set ID
Demo
4. Press the EXIT button to return to normal
OSD Rotate
viewing.
Menu Prev.
-
-
-
ISM
This set
programmed to remember which option it was last set to event if you turn the set off.
In Child lock 'On', if the set is turned off, press the INPUT SELECT button on the set or POWER, INPUT
SELECT or MULTIMEDIA button on the remote control.
With the Child lock On, the display
pressed while viewing the set.
(Image Sticking Minimization)
'
Child lock on' appears
1. Press the MENU button and then
the
screen
if any button
on
the front
panel
is
Method
Frozen still picture from a PC/video game displayed
image remaining even when you change the image.
a long period of time.
-
on
use
/
the screen for prolonged periods will result in an ghost
Avoid allowing a fixed image to remain on the set's screen for
on
button to select the SPECIAL
menu.
SPECIAL
Language
Child lock
2. Press the
button and then
3. Press the
Orbiter
?
button and then
or
White Wash :
White Wash removes
Orbiter
button to select either Normal, White wash,
function, set Normal.
/
Inversion. If you unnecessary to set this
permanent images from the
Note: An excessive permanent
Wash.
?
button to select ISM Method.
/
image
may be
to clear
entirely
with White
:
Orbiter may help prevent ghost images. However, it is best not to allow any fixed
image to remain on the screen. To avoid a permanent image on the screen, the
screen
?
will
move
Inversion
every 2 minutes.
:
This is the function to invert the
ically
panel
color of the
inverted every 30 minutes.
4. Press the EXIT button to return to normal
20
PLASMA MONITOR
viewing.
screen.
Normal
Low power
White wash
Set ID
Orbiter
Demo
OSD Rotate
Menu Prev.
screen.
impossible
ISM Method
The
panel
color is automat-
Inversion
Operation
Low Power
-
This is the function to reduce the power
1. Press the MENU button and then
consumption
use
of the set.
button to select the SPECIAL
/
menu.
SPECIAL
Language
2. Press the
button and then
3. Press the
button and then
use
button to select Low power.
/
use
button to select On
/
or
Child lock
ISM Method
Off.
Low power
On
Set ID
Off
Demo
4. Press the EXIT button to return to normal
viewing.
OSD Rotate
Menu
Demo
-
Use it to
see
Prev.
(option)
the difference between XD demo
-I t 's not available to
use
on
and XD Demo off.
this function in Rotate mode.
1. Press the MENU button and then
use
button to select the SPECIAL
/
menu.
SPECIAL
Language
2. Press the
button and then
3. Press the
button to
begin
use
button to select XD Demo.
/
Child lock
ISM Method
Low power
XD Demo.
Set ID
Demo
4. To
stop
XD
Demo, press the EXIT button.
Menu
Menu Rotation for Vertical
To start
OSD Rotate
Prev.
Viewing
1. Press the MENU button and then
use
button to select the SPECIAL
/
menu.
SPECIAL
Language
2. Press the
button and then
use
button to select OSD Rotate.
/
Child lock
ISM Method
3. Press the
?
?
button and then
use
the
/
Select Normal
:
Select Rotate
if the monitor is installed
:
button to select Normal
if the monitor is installed
4. Press the EXIT button to return to normal
horizontally.
vertically.
viewing.
or
Rotate.
Low power
Set ID
Demo
OSD Rotate
Normal
Rotate
Menu
Prev.
Owner's Manual
21
Operation
Screen
Screen Menu
Auto
-
Options
Options
mode
adjustment (RGB [PC]
Automatically adjusts picture position
1. Press the MENU button and then
only)
and minimizes
/ E
use D
image shaking.
button to select the SCREEN
menu.
SCREEN
Auto
2. Press the G button and then
button to select Auto
/ E
use D
3. Press the G button to start Auto config..
?
When Auto config. has finished, Ok will be shown
?
4. If
If the
position
of the
image
is still not correct,
needs to be adjusted
the Manual config..
picture
To set
config.
Position
Manual
config.
Reset
on screen.
try Auto adjustment again.
after Auto
more
config..
ARC
in RGB
adjustment
(PC),
you
can
adjust
Menu Prev.
5. Press the EXIT button to return to normal
-
-
viewing.
Although the image is still not correct, your set is functioning properly but needs further adjustment.
The Auto config. and the Manual config. functions don't need to be run for DVI mode.
Setting
Picture Format
You can watch the screen in various picture formats; Spectacle, Full, Original (option),
Zoom.
-I t 's available to use Original in MZ-42PM10/11/12X/20/21 / MZ-50PM10/11/20/21 series.
-
1. Press the MENU button and then
/
use
button to select the SCREEN
4:3, 16:9 (Wide), 14:9 and
menu.
SCREEN
Auto
2. Press the
button and then
button to select ARC.
/
use
config.
Spectacle
ARC
Position
3. Press the
(option),
?
button and then use
4:3, 16:9, 14:9 or Zoom.
button to select Spectacle, Full,
/
Manual
Original
config.
16:9
14:9
Zoom
Spectacle
When your set receives the wide screen signal, following selection will lead you to
the picture horizontally, in a linear proportion, to fill the entire screen.
adjust
Prev.
Menu
Full
When your set receives the wide screen signal, following selection will lead you to
the picture horizontally or vertically, in a linear proportion, to fill the entire screen
?
?
adjust
fully.
Original (option)
When your set receives the wide
picture format to be sent.
?
signal,
screen
it will be
automatically changed
to the
4:3
Following
gray bars
selection will lead you to view
at both the left and
a picture with
right sides.
appearing
16:9 (Wide)
Following selection
an
original
4:3
aspect ratio, with
?
to fill the entire
will lead you to adjust the picture horizontally, in
(useful for viewing 4:3 formatted DVDs).
a
linear
proportion,
screen
14:9
You can enjoy the picture format of 14:9 or general TV programme through the 14:9
mode. The screen 14:9 is viewed just like that the screen 4:3 is magnified to the left /
?
right.
?
Zoom
Following
the entire
selection will lead you to view the picture without any alternation, while filling
However, the top and bottom portions of the picture will be cropped.
screen.
4. Press the EXIT button to return to normal
-
-
You
can
You
can
only
only
select 4:3 and 16:9
select
in
(Wide)
viewing.
RGB[PC], DVI[PC].
4:3, 16:9 (Wide) and Zoom in Component 480p/576p/720p/1080i, RGB[DTV]
or
DVI[DTV].
Screen Position
-
This function works in the following mode:
RGB-PC or COMPONENT 480p/576p/720p/1080i.
1. Press the MENU button and then
button to select the SCREEN
/
menu.
SCREEN
Auto
2. Press the
button and then
/
3. Press the
button and then
/
button to select Position.
or
/
4. Press the EXIT button to return to normal
button to
adjust
the
config.
ARC
Position
position.
Manual
config.
Reset
viewing.
Menu Prev.
22
Full
Original
4:3
Reset
PLASMA MONITOR
Operation
Manual
-
-
mode
Configure (RGB [PC]
If the
isn't clear after auto
picture
phase manually.
To correct the
only)
adjustment
and
especially
that characters
are
still
trembling, adjust
the
picture
size, adjust Clock.
screen
1. Press the MENU button and then
button to select the SCREEN
/
menu.
SCREEN
Auto
2. Press the
button and then
/
button to select Manual
3. Press the
button and then
/
button to select Phase
4. Press the
?
The
?
The
/
button to make
adjustment
adjustment
-
-
To
In
see a
some
Menu
Prev.
(RGB[PC]
mode
Auto
config.
only)
match the resolution of RGB mode and selection of VGA/XGA mode.
not available to selection of XGA mode.
use
2. Press the
button and then
use
/
3. Press the
button and then
use
/
/
button to select the SCREEN
button to select VGA Mode
(or
menu.
XGA
Mode).
button to select the desired VGA/XGA resolution.
4. Press the EXIT button to return to normal
SCREEN
ARC
Position
Manual
config.
Reset
640x480
848x480
viewing.
852x480
Menu
-
0
viewing.
VGA Mode
-
0
~
1. Press the MENU button and then
Screen
Phase
Clock
~
picture,
models, it's
config.
Reset
30.
range of Phase is 0
+128.
range of Clock is -127
Wide VGA/XGA mode
normal
Position
Manual
Clock.
appropriate adjustments.
5. Press the EXIT button to return to normal
Selecting
config..
or
config.
ARC
Prev.
Adjustments
Use this function to correct
jittering or picture instability
following mode:
(or AV1, AV2), S-Video or Component 480i/576i.
while
viewing
a
video
tape.
This function works in the
AV
1. Press the MENU button and then
use
/
button to select the SCREEN
menu.
SCREEN
Screen
2. Press the
3. Press the
button and then
button and then
?
Select the VCR
?
Select the TV
use
use
button to select Screen
/
button to select TV
/
or
adj..
adj.
TV
VCR
ARC
Cinema
YNR
VCR.
Reset
option if watching a VCR.
option for other equipment.(Except VCR)
4. Press the EXIT button to return to normal
viewing.
Prev.
Menu
Cinema
-
-
When you watch the movie, this function adjusts the set to the best
This function works in the following mode:
AV
(or AV1, AV2),
S-Video
or
picture
appearance.
COMPONENT 480i/576i.
1. Press the MENU button and then
use
/
button to select the SCREEN
menu.
SCREEN
Screen
2. Press the
button and then
use
/
button to select Cinema.
3. Press the
button and then
use
/
button to select On
4. Press the EXIT button to return to normal
or
Off.
adj.
ARC
Cinema
On
YNR
Off
Reset
viewing.
Menu
Prev.
Owner's Manual
23
Operation
Screen
Screen Menu
Luminance Noise Reduction
-
-
You
(option)
picture noise
following mode:
(or AV1, AV2), S-Video or Component 480i/576i.
can
select On
Options
Options
or
Off to reduce the
which may appear
on
the
screen
during watching
the TV.
This function works in the
AV
1. Press the MENU button and then
use
button to select the SCREEN
/
menu.
SCREEN
Screen
2. Press the
button and then
use
button to select YNR.
/
adj.
ARC
Cinema
3. Press the
button and then
use
button to select On
/
4. Press the EXIT button to return to normal
or
YNR
Off.
On
Reset
Off
viewing.
Menu Prev.
to
Initializing (Reset
This function
original factory value)
operates in
To initialize the
current mode.
value
adjusted
1. Press the MENU button and then
button to select the SCREEN
/
menu.
SCREEN
Screen
2. Press the
button and then
3. Press the
?
You
can
and sub
button to select Reset.
/
Cinema
YNR
button.
initialize
Reset
Position,
size of twin
picture
adj.
ARC
SPLIT
PIP
ZOOM,
size,
PIP
position,
PIP
Transparency
picture.
Menu Prev.
Split
-
Zoom
This is the function to
-I t 's available to
enlarge
the
with
screen
ration.
regular
this function in every input source.
-I t 's not available to use this function in Rotate mode.
-
-
use
With 2-SPLIT
ZOOM, you
If
enlarged,
1.
a screen
is
can
only
the
move
a screen can move
into upside or downside.
selecting a section of screen.
screen
without
Press the SPLIT ZOOM button.
?
Each press of SPLIT ZOOM button
2-Split
changes
the
4-Split
zoom
1
case
of
display
as
shown below.
9-Split zoom
zoom
1
2
4
5
123
FG
4
In
screen
456
Zoom:
9-Split
Press the number button to select the section you want to enlarge.
If you choose No.5, the 5 section is enlarged and also can move the
using
the
9-Split
FG
789
/
or
/
In
zoom
enlarged
screen
with
button.
case
of
choosing
the No.5
123
456
FG
789
The 5 section is
24
PLASMA MONITOR
changed
to
a
full
screen.
To set
Operation
PIP
-
(Picture-in-Picture)
(Picture-in-Picture) Feature
PIP lets you view 2 different
inputs (sources)
your set
screen
at the
same
time.
PIP
Watching
Press the PIP/DW button to show the sub
?
on
Each press of PIP/DW button
changes
picture.
the
display
screen
as
shown below.
PIP
DW1
DW2
Off
Note: The motion of the sub picture can be unnatural because the set displays full screen by synchronizing the main
when the refresh rate between the main picture source and the sub picture source is different in PIP mode.
picture
source
Moving
the PIP
mode
(PIP
only)
Press the POSITION button.
Selecting
an
Input Signal
Press the PIP INPUT button to select the
sub
/
Repeatedly press the
tion is achieved. The sub
Source for the PIP
input
source
or
picture
/
button until desired
moves
up/down
or
posileft/right.
for the
picture.
RGB
Win.
AV
10:30
position
D
FG
E
Picture Size
?
In
RGB, DVI and COMPONENT 480p/576p/720p/1080i for
main picture, you can select AV (or AV1, AV2), S-Video
and COMPONENT 480i/576i for sub
?
?
picture.
(or AV1, AV2), S-Video and COMPONENT 480i/576i
for main picture, you can select COMPONENT
480p/576p/720p/1080i, RGB and DVI for sub picture.
You can't select the same modes for main picture and sub
picture simultaneously.
In AV
Press the WIN.SIZE button and then
sub
picture
With WIN.SIZE button in
picture
PIP
/
button to
adjust the
size.
DW1, DW2 modes, main and sub
is
adjusted simultaneously.
mode, sub picture is adjusted.
With WIN.SIZE button in
Win. size
Adjusting
PIP
Transparency (PIP
1. Press the MENU button and then
2. Press the
button and then
3. Press the
button and then
?
The
adjustment
range of PIP
mode
/
only)
button to select the PIP/DW
menu.
/
button to select PIP
Transparency.
/
button to
transparency.
adjust
Transparency is
4. Press the EXIT button to return to normal
0
PIP
~
10.
viewing.
Owner's Manual
25
Miscellaneous
External Control
Control Device Setup
Connect the RS-232C
-
input jack to an external
externally.
control device
(such
as a
computer
or an
A/V control
system)
and control the set's functions
How to connect external control
?
Connect the serial
?
RS-232C connection cables
?
The set remote control and front
computer
?
or
of connector; D-Sub
No.
Pin
1
No connection
Monitor back
panel.
not be functional if the Monitor is controlled
are
used for service.
9-pin
male
1
RXD
3
TXD
4
DTR
5
GND
6
DSR
5
(Receive data)
(Transmit data)
(DTE side ready)
9
(DCE side ready)
(Ready to send)
(Clear to send)
7
RTS
8
CTS
9
No Connection
6
configurations
7-wire
(Standard
PC
3-wire
configuration
(Not standard)
configuration
RS-232C cable)
PDP
PC
PDP
TXD
RXD
3
TXD
RXD
2
3
TXD
2
RXD
TXD
3
2
RXD
5
GND
GND
5
5
GND
GND
DTR
DSR
RTS
CTS
2354678
D-Sub 9
26
to the RS-232C jack on the
supplied with the set.
panel controls (except main power) will
not
name
2
RS-232C
are
other external device.
RS-232C connection cables
Type
equipment
port of the control device
PLASMA MONITOR
6
DSR
DTR
4
4
DTR
4
DTR
DSR
6
6
DSR
8
CTS
RTS
7
7
RTS
7
RTS
CTS
8
8
CTS
D-Sub 9
D-Sub 9
D-Sub 9
by
a
PC
Miscellaneous
Set ID
-
-
Use this function to
specify a set ID number.
Mapping 1'. See page 31.
Refer to 'Real Data
1. Press the MENU button and then
the
use
button to select the SPECIAL
/
menu.
SPECIAL
Language
2. Press the
button and then
use
3. Press the
button and then
use
button to select Set ID.
/
Child lock
ISM Method
F / G button to
adjust Set
Low power
ID to choose the desired
1
Set ID
monitor ID number.
Demo
OSD Rotate
?
The
adjustment
range of Set ID is 1
~
99.
4. Press the EXIT button to return to normal
viewing.
Menu
Prev.
Communication Parameters
?
Baud rate
?
Data
?
*
:
9600
bps (UART)
length : 8
Parity : None
bits
Use
(reverse)
a
crossed
?Stopbit:1bit
?
Communication code
Transmission /
COMMAND 1 COMMAND 2
DATA
[Command1][Command2][ ][Set ID][ ][Data][Cr]
k
a
0~1
Input Select
Aspect Ratio
k
b
0~5
k
c
0~6
*
04. Screen Mute
k
d
0~1
*
05. Volume Mute
k
e
0~1
06. Volume Control
k
f
0~64
07. Contrast
k
g
0~64
08.
03.
Protocol
Receiving
Transmission
(Hexadecimal)
02.
ASCII code
cable.
Command Reference List
01. Power
:
*
[Command 1]
First command to control PDP set.
:
(jork)
[Command 2]
[Set ID]
:
Second command to control PDP set.
:
You
can
adjust
the set ID to choose
desired monitor ID number in
menu.
See
special
previous
page.
99.
Adjustment range is 1
When selecting Set ID '0', every
~
k
h
0~64
09. Colour
k
i
0~64
Set ID is indicated
10. Tint
k
j
0~64
menu
11.
k
k
0~64
Brightness
Sharpness
k
l
0~1
13. Remote control lock mode
k
m
0~1
14. PIP/DW
k
n
0~3
k
p
0~99
16. PIP Position
k
q
0~3
17. Treble
k
r
0~64
18. Bass
k
s
0~64
19. Balance
k
t
0~64
Split
Zoom
20. Colour
0~3
0~3C
22. Green
k
w
0~3C
23.
k
$
0~3C
y
0~5
k
z
0~9
26. ISM Method
j
j
j
j
j
27. Low Power
28. Orbiter Time
29. Orbiter
Setting
Pixel Setting
Size Setting for
30. Picture
D/W Mode
31. Auto
Configure
j
0~1
r
1~FE
s
1~9
t
0~14
1
When
setting
the 25
31,
~
a menu
doesn't
display
on
'space (0x20)'
OK Acknowledgement
*
The Monitor transmits ACK
(acknowledgement)
this format when
receiving
normal data. At this
data is data read
mode, it indicates present status data. If
mode, it returns the data of the PC
based
on
time, if the
[Command2][ ][Set ID][ ][NG][Data][x]
*
The Monitor transmits ACK
(acknowledgement)
this format when
abnormal data from
receiving
non-viable functions
or
communication
based
on
errors.
20)
Data
1:
Illegal
2: not
*
ASCII code
:
Error Acknowledgement
0~3
u
Return
ASCII code '0x0D'
computer.
p
or
Carriage
:
the data is data write
q
(1E
[Cr]
[Command2][ ][Set ID][ ][OK][Data][x]
u
v
k
as
Hexa decimal
To transmit command data.
:
*[]
k
25. Abnormal State
as
command.
*
Temperature (CSM) k
24.
and
Transmit 'FF' data to read status of
21. Red
Adjustment
Adjustment
Blue Adjustment
PIP input select
[DATA]
decimal
(1~99)on
(0x0~0x63)
transmission/receiving protocol.
on
*
12. OSD Select
15.
connected PDP set is controlled.
Code
support function
3: Wait
more
time
screen.
Owner's Manual
27
Miscellaneous
01. Power
2
04. Screen Mute
(Command
G To control Power On/Off of the Monitor.
G To select
mute on/off.
Transmission
Transmission
(Command
:
a)
[k][a][ ][Set ID][ ][Data][Cr]
Data
0
d)
:
[k][d][ ][Set ID][ ][Data][Cr]
Power Off
:
screen
2
Data
1:PowerOn
0
:
Screen mute off
1
:
Screen mute
(Picture on)
(Picture off)
on
Ack
Ack
[a][ ][Set ID][ ][OK][Data][x]
[d][ ][Set ID][ ][OK][Data][x]
G To show Power On/Off.
Transmission
05. Volume Mute
(Command
[k][a][ ][Set ID][ ][FF][Cr]
G To control volume
mute on/off.
Ack
You
mute
the MUTE button
using
on
Transmission
In like manner, if other functions transmit '0xFF' data
based on this format, Acknowledgement data feed back
[k][e][ ][Set ID][ ][Data][Cr]
Data
status about each function.
presents
adjust
e)
:
remote control.
[a][ ][Set ID][ ][OK][Data][x]
*
also
can
2
0
:
Volume mute
1
:
Volume mute off
(Volume off)
(Volume on)
on
Ack
02.
Select
Input
G To select input
You
(Command
source
also select
can
SELECT button
on
an
2
:
b)
[e][ ][Set ID][ ][OK][Data][x]
for the Monitor.
input
using
source
the INPUT
the Monitor's remote control.
06. Volume Control
Transmission
0:RGB
You
:
on
3:AV(orAV1)
4 : S-Video (or AV2)
5 : S-Video (option)
1:DVI
2
2
:
f)
G To adjust volume.
[k][b][ ][Set ID][ ][Data][Cr]
Data
(Command
Component
can
also
adjust
volume with the volume buttons
remote control.
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Ack
Data
[b][ ][Set ID][ ][OK][Data][x]
Min:0~Max:64
*
Refer to 'Real data
mapping
1'. See page 31.
Ack
03.
Ratio
Aspect
G To adjust the
(Command
2
:
c) (Main
Picture
Size)
format. (Main picture format)
adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the
You
screen
also
can
SCREEN
menu.
:
1:full
5
:
2
6
:
3
:
:
can
(Command
screen
also
2
:
g)
contrast.
adjust
contrast in the PICTURE
menu.
[k][g][ ][Set ID][ ][Data][Cr]
4
:
G To adjust
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
0
07. Contrast
You
Transmission
Data
[f][ ][Set ID][ ][OK][Data][x]
Spectacle
Original
Normal
screen
Wide
(16:9)
Wide screen (14:9)
Full screen (Zoom)
screen
(4:3)
Data
Min:0~Max:64
*
Refer to 'Real data
mapping
1'. See page 31.
Ack
[g][ ][Set ID][ ][OK][Data][x]
Ack
[c][ ][Set ID][ ][OK][Data][x]
*
Using
the PC
input,
you select either 16:9
aspect ratio.
or
4:3
screen
08.
Brightness (Command
G To adjust
You
can
2
brightness.
adjust brightness
:
h)
screen
also
in the PICTURE
menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:64
*
Refer to 'Real data
mapping
Ack
[h][ ][Set ID][ ][OK][Data][x]
28
PLASMA MONITOR
1'. See page 31.
Miscellaneous
09. Colour
(Command
G To adjust the
You
can
also
screen
adjust
2
i)
:
14.PIP/DW(Command2:n)
G To control the PIP (Picture In picture)/DW.
colour.
colour in the PICTURE
You
menu.
on
Transmission
using
in the PIP/DW
or
the PIP/DW button
menu.
[k][n][ ][Set ID][ ][Data][Cr]
Min:0~Max:64
*
also control the PIP/DW
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data
can
the remote control
Refer to 'Real data
mapping
1'. See page 31.
Data 0: PIP/DW off
Ack
1: PIP
[i][ ][Set ID][ ][OK][Data][x]
2: DW1
3: DW2
10. Tint
(Command
G To adjust the
You
can
also
screen
adjust
2
:
Ack
j) (option)
[n][ ][Set ID][ ][OK][Data][x]
tint.
tint in the PICTURE
menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data
15.
Red:0~Green:64
*
Refer to 'Real data
mapping
Zoom
Split
(Command
G To operate split
1'. See page 31.
zoom
2
:
p)
function and select the
split
zoom
section number.
Ack
Transmission
[j][ ][Set ID][ ][OK][Data][x]
[k][p][ ][Set ID][ ][Data][Cr]
Data
11.
2
Sharpness (Command
G To adjust the
You
can
also
k)
:
sharpness.
adjust sharpness in
Min: 0
?
menu.
Transmission
Max: 99
Selection 1 of 2
Refer to 'Real data
screen
the PICTURE
~
Data 21:
ex.
split
zoom.
2'.
mapping
Ack
[p][ ][Set ID][ ][OK][Data][x]
[k][k][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:64
*
Refer to 'Real data
1'. See page 31.
Ack
[k][ ][Set ID][ ][OK][Data][x]
12. OSD Select
Real data
*
mapping
(Command
2
:
l)
G To select OSD (On Screen Display) on/off when
con-
trolling remotely.
Transmission
2
mapping
0
:
Reset
21
:
Selection 1 of 2
24
:
Selection 4 of 2
41
:
Selection 1 of 4
42
:
Selection 2 of 4
44
:
Selection 4 of 4
45
:
Selection 5 of 4
91
:
99
:
split
zoom
zoom
Selection 1 of 9
split
split
split
split
split
split
split
Selection 9 of 9
split
zoom
zoom
zoom
zoom
zoom
zoom
zoom
[k][l][ ][Set ID][ ][Data][Cr]
Data0
:OSDoff
1:OSDon
Ack
16. PIP Position
[l][ ][Set ID][ ][OK][Data][x]
You
13. Remote control lock mode
G To lock the front panel controls
(Command
on
2
:
m)
the monitor and remote
Transmission
Lock off
1:Lockon
you're
q)
also
adjust the
on
sub
picture position using
the remote control
or
in the PIP/DW
POSImenu.
down
0
:
Right
1
:
Left down
2
:
Left up
3
:
Right
on screen
on screen
on screen
up
on screen
Ack
[m][ ][Set ID][ ][OK][Data][x]
If
:
Transmission
Data
Ack
*
can
TION button
[k][m][ ][Set ID][ ][Data][Cr]
:
2
[k][q][ ][Set ID][ ][Data][Cr]
control.
Data 0
(Command
G To select sub picture position for PIP.
not
using
the remote
When main power is
released.
[q][ ][Set ID][ ][OK][Data][x]
control,
use
this mode.
on/off, external control lock is
Owner's Manual
29
Miscellaneous
17. Treble
(Command
2
22. Green
:r)
G To adjust treble.
You
can
also
adjust
treble in the SOUND
menu.
w)
Transmission
[k][w][ ][Set ID][ ][Data][Cr]
[k][r][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:64
*
:
G To adjust green in colour temperature.
Transmission
Data
2
Adjustment (Command
Refer to 'Real data
Min:0~Max:3C
Refer to 'Real data
*
mapping
1'. See page 31.
Ack
mapping
3'. See page 31.
Ack
[w][ ][Set ID][ ][OK][Data][x]
[r][ ][Set ID][ ][OK][Data][x]
18. Bass
(Command
2
23. Blue
:
s)
G To adjust bass.
You
can
also
adjust
bass in the SOUND
Transmission
[k][$][ ][Set ID][ ][Data][Cr]
Data
[k][s][ ][Set ID][ ][Data][Cr]
Refer to 'Real data
Min:0~Max:3C
*
Min:0~Max:64
*
$)
:
menu.
Transmission
Data
2
Adjustment (Command
G To adjust blue in colour temperature.
Refer to 'Real data
3'. See page 31.
mapping
Ack
mapping
1'. See page 31.
Ack
[$][ ][Set ID][ ][OK][Data][x]
[s][ ][Set ID][ ][OK][Data][x]
24. PIP
19. Balance
(Command
2
:
t)
can
also
adjust
ture mode. You
balance in the SOUND
Refer to 'Real data
mapping
Temperature (Command
2
:
also
0:RGB
2
remote control.
adjust
0: Cool
3:AV(orAV1)
4 : S-Video (or AV2)
5 : S-Video (option)
Component
:
25. Abnormal State
CSM in the PICTURE
menu.
G To recognize
an
(Command
2
:
z)
abnormal state.
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
[k][z][ ][Set ID][ ][FF][ ][Cr]
1: Normal
2: Warm
3: User
Ack
Data
FF
:
Read
Ack
[u][ ][Set ID][ ][OK][Data][x]
[z][ ][Set ID][ ][OK][Data][x]
Data
21. Red
Adjustment (Command
2
:
v)
0: Normal
(Power on and signal exist)
signal (Power on)
Turn the monitor off by remote control
Turn the monitor off by sleep time function
Turn the monitor off by RS-232C function
1: No
2:
G To adjust red in colour temperature.
3:
Transmission
4:
[k][v][ ][Set ID][ ][Data][Cr]
5: 5V down
6: AC down
Min:0~Max:3C
*
Refer to 'Real data
7: Turn the monitor off
mapping
3'. See page 31.
8: Turn the monitor off
Ack
9: Turn the monitor off
[v][ ][Set ID][ ][OK][Data][x]
30
on
PLASMA MONITOR
*
This function is "read
only".
by
by
by
Fan Alarm function
Off time function
Auto
pic-
for sub
u)
Transmission
Data
picture
adjust input source
[y][ ][Set ID][ ][OK][Data][x]
G To adjust colour temperature.
Data
also
y)
in PIP/Twin
Ack
[t][ ][Set ID][ ][OK][Data][x]
can
for sub
1:DVI
1'. See page 31.
Ack
You
can
:
[k][y][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:64
20. Colour
source
2
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
*
(Command
PIP INPUT button
picture using
menu.
Transmission
Data
Select
G To select input
G To adjust balance.
You
Input
sleep
function
Miscellaneous
26. ISM Method
(Command
30. Picture Size
1
:
j,
Command 2
G To control the ISM method. You
Method in SPECIAL
:
p)
(Command
also
can
adjust
ISM
1
Setting for DW Mode
: j, Command 2 : t)
G To select the PIP picture format.
You
menu.
can
also select the PIP
WIN.SIZE
Transmission
on
format
picture
using
the
the remote control.
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
Data 0
:
Normal Mode
2
:
Orbiter
1
:
White Wash
3
:
Inversion
[j][t][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:14(1Eor20)
Refer to 'Real data mapping
*
Ack
1'. See page 31.
Ack
[p][ ][Set ID][ ][OK][Data][x]
[t][ ][Set ID][ ][OK][Data][x]
27. Low Power
(Command
1
:
j,
Command 2
:
q)
31. Auto
G To reduce the power consumption of the monitor. You
also
can
adjust
Low Power in SPECIAL
menu.
Configure
(Command 1 : j,
automatically.
Transmission
:Off
1
:On
It works
only
[q][ ][Set ID][ ][OK][Data][x]
[u][ ][Set ID][ ][OK][Data][x]
28. Orbiter Time
(Command
1
Setting
: j, Command
G To adjust orbiter operation time
2
:
(PC)
mode.
r)
term.
Transmission
*
[j][r][ ][Set ID][ ][Data][ ][Cr]
*
in RGB
1: To set
Ack
Min: 1
u)
[j][u][ ][Set ID][ ][Data][Cr]
Data
Ack
Data
:
Transmission
[j][q][ ][Set ID][ ][Data][ ][Cr]
Data 0
Command 2
G To adjust picture position and minimize image shaking
~
Real data
mapping
1
Real data
0
:Step0
0:-30
A
:Step10(SetID10)
2:-28
F
:Step15(SetID15)
:Step16(SetID16)
1E:0
mapping
3
1:-29
Max: FE
Refer to 'Real data
*
mapping
1'. See page 31.
Ack
[r][ ][Set ID][ ][OK][Data][x]
10
3A:+28
64
:
Step
100
6E
:
Step
110
G To adjust pixel number in orbiter function.
73
:
74
:
Step
Step
115
Transmission
C7
:
Step
199
29. Orbiter Pixel
(Command
1
Setting
: j, Command
3C:+30
2
:
s)
[j][s][ ][Set ID][ ][Data][Cr]
Data
Min:1~Max:9
*
Refer to 'Real data
mapping
3B:+29
116
1'. See page 31.
Ack
[s][ ][Set ID][ ][OK][Data][x]
Owner's Manual
31
Miscellaneous
IR Code
Code
(NEC
(NEC Format)
How to connect
G
Connect your wired remote control to the Remote Control
Remote Control IR Code
port
on
the Monitor.
(NEC Format)
G Output waveform
Single pulse,
modulated with 37.917KHz
at 455KHz
signal
TC
Carrier
frequency
FCAR
1/TC
Duty
T1
=
ratio
=
=
fOSC/12
T1/TC
1/3
=
G Configuration of frame
?
1st frame
Lead
Low
High
code
custom code
custom code
Data code
Data code
C0 C1C2C3C4C5C6C7C0C1C2C3C4C5C6C7D0D1D2D3D4D5D6D7D0D1D2D3D4D5D6D7
?
Repeat
frame
Repeat
code
Tf
G Lead code
9ms
4.5
ms
0.55
G Repeat code
ms
9ms
2.25
ms
G Bit description
?
?
Bit "0"
0.56
0.56
1.12
G Frame interval
:
Bit "1"
ms
2.24
ms
Tf
The waveform is transmitted
Tf
as
long
as a
key
is
depressed.
Tf
Tf=108ms @455KHz
32
PLASMA MONITOR
ms
ms
Miscellaneous
Code
Note
00
UP
(D)
R/C Button
01
DOWN
(E)
VOL+ (G)
VOL- (F)
R/C Button
08
POWER
R/C Button
C4
POWER ON
Discrete IR Code
C5
POWER OFF
Discrete IR
09
MUTE
R/C Button
10
Number
11
Number
12
Number
13
Number
14
Number
15
Number
16
Number
17
Number
18
Number
19
Number
0B
INPUT SELECT
R/C Button
98
MULTIMEDIA
R/C Button
BF
COMPONENT
Discrete IR Code
C6
DVI
Discrete IR Code
D5
RGB
Discrete IR Code
5A
AV1
Discrete IR Code
AV2
Discrete IR Code
D8
S-VIDEO
Discrete IR Code
0E
SLEEP
R/C Button
43
MENU
R/C Button
44
OK( )
R/C Button
4D
PSM
R/C Button
52
SSM
R/C Button
62
POSITION
R/C Button
64
WIN.SIZE
R/C Button
60
PIP/DW
R/C Button
61
PIP INPUT
R/C Button
63
SWAP
R/C Button
7B
SPLIT ZOOM
R/C Button
79
ARC
R/C Button
76
ARC
77
ARC
AF
ARC
02
03
D0
Function
(Hexa)
(option)
Key
Key
Key
Key
Key
Key
Key
Key
Key
Key
(4:3)
(16:9)
(Zoom)
R/C Button
R/C Button
0
R/C Button
1
R/C Button
2
R/C Button
3
R/C Button
4
R/C Button
5
R/C Button
6
R/C Button
7
R/C Button
8
R/C Button
9
R/C Button
(Power On/Off)
(Only Power On)
Code (Only Power Off)
Discrete IR Code
Discrete IR Code
Discrete IR Code
COMPONENT
(Input
(Input
(Input
(Input
(Input
(Input
Selection)
Selection)
RGB Selection)
AV1 Selection)
AV2 Selection)
S-VIDEO Selection)
(Only
(Only
(Only
4:3
DVI
mode)
mode)
Zoom mode)
16:9
Owner's Manual
33
Miscellaneous
Checklist
Checklist
Troubleshooting
Troubleshooting
No
picture
&
?
Check whether the set is turned
?
Power cord inserted into wall outlet?
on.
No sound
?
another
was
?
Sound muted? Press MUTE button.
Check to
causing
?
The remote control
see
to
p.6)
No
new
batteries.
as
the
(Refer
to
image
is muted
p.6)
during the startup process of
picture has not appeared
Please contact your service centre, if the
minutes.
Select Colour in the PICTURE
to
menu
Keep
?
Activate any function to restore the
still
one
of the
Unusual sound from
inside the set
picture
is
on
the
screen
for
?
Check for local interference such
?
Adjust
?
A
PLASMA MONITOR
Balance in the SOUND
change
in ambient
at the time of
the set.
(G)
after five
button.
certain distance between the set and the VCR.
?
a
and press the VOLUME
the set.
p.17)
of the
brightness
more
as an
than 5
menu.
electrical
(Refer
picture.
minutes, the
picture shaking
output from
polarities.
This is normal
speakers
34
installed with the correct
are
?
(If
or
if the batteries
Install
picture
Horizontal/vertical bars
between the set and the remote control
object
Check if the remote control handset is set up to correct mode.
(Refer
Poor colour
if there is any
see
?
?
Poor
button.
?
Picture appears slowly,
after switching on
or
(G)
obstruction.
Check to
(Refer
doesn't work
or
power cord into the wall outlet where the set's power
Press the VOLUME
?
No
product's
plugged in.
?
Picture OK &
No sound
Plug
cord
to
appliance
screen
or
gets dark.)
power tool.
p.18)
humidity or temperature may result in an unusual noise
switching off or on of the set and does not indicate a fault with
Miscellaneous
Product
Specifications
MT-42PM10/11/H/B/R/S
MT-42PM12X/H/B/R/S
MT-42PM20/21/H/B/R/S
MODEL
MZ-42PM10/11/H/B/R/S
MZ-42PM12X/H/B/R/S
MZ-42PM20/21/H/B/R/S
(inches
/
mm)
42 / 1066
Height (inches
/
mm)
25.6 / 650
Depth (inches
/
mm)
3.9 / 97.5
Width
Weight (pounds
Power
/
66/30
kg)
AC100-240V, 50/60Hz
requirement
Resolution
852
x
480
1024
(Dot)
32
Operating Temperature Range
MODEL
104°F
(0
40°C)
~
MT-50PM10/11/H/B/R/S
MT-50PM20/21/H/B/R/S
MZ-50PM10/11/H/B/R/S
MZ-50PM20/21/H/B/R/S
/
mm)
49.3 / 1253
Height (inches
/
mm)
29.3 / 745
Depth (inches
/
mm)
4/99.5
/
90.4 / 41
kg)
AC100-240V, 50/60Hz
requirement
Resolution
1366
Colour
32
768
(Dot)
shown above may be
~
104°F
(0
40°C)
~
Less than 80%
Operating Humidity Range
specifications
x
16,770,000 (256 steps of each R, G and B)
Operating Temperature Range
The
~
(inches
Weight (pounds
?
(Dot)
Less than 80%
Operating Humidity Range
Power
768
16,770,000 (256 steps of each R, G and B)
Colour
Width
x
changed
without notice for
quality improvement.
Owner's Manual
35
Download PDF