LG | RT-37LZ30 | LG RT-37LZ30 Owner’s Manual

LCD
Colour Television
OWNER'S MANUAL
Please read this manual
carefully
before
operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
and quote this
information to your dealer when you require service.
Model number
:
Serial number
:
P/NO
:
3828TUL300B
Printed in Korea
on
the back
(0412-REV00)
cover
Contents
Installation
3
Location and function of controls
Remote control
Internal generator charge / Front/Side
4
panel
/ Back
panel
Basic operation
On and off / Programme selection
Volume adjustment
Quick view / Mute function
On screen language selection (option)
8
ON SCREEN Menus
Menu selection
9
STATION Menu
Auto programme tuning
Manual programme tuning
Assigning a station name/Fine tuning
Programme edit
Favourite programme/Calling the programme table
10
PICTURE Menu
PSM (Picture Status
Picture adjustment
ACC/ XD
15
Memory)
SOUND Menu
SSM (Sound Status Memory)
Sound adjustment/SRS WOW
Stereo/Dual reception / NICAM
Sound output selection
TIMER menu
Clock / On/Off Time / Auto Off /
17
reception
20
Sleep
timer
SPECIAL Menu
Main Picture Source Selection
Child lock/Power Indicator/Transparency
Picture Size Zoom/Reset
22
SCREEN Menu
Picture format
Auto adjustment /Clock and Phase
SCREEN Position
Manual Configure
Screen adjustments
25
Initializing (Reset to original factory value)
Selecting Wide XGA mode
YNR (Y-signal Noise Reduction) / Split Zoom
PIP/POP/PBP operation
PIP/POP/PBP mode / Input mode selection for sub picture
Sub Picture / Size Source
Image / Sound /Moving the sub Picture
Swap / Swapping between main and sub
Programme selection for sub picture
Teletext (option)
Switch on/off / SIMPLE text / TOP text
FASTEXT / Special teletext functions
pictures
32
(option)
Connection of external equipment
Aerial socket / Euro scart sockets
S-Video/Audio in sockets (S-Video)
PC in socket / Audio/Video in sockets
35
Displayable
37
External Control Device Setup
RS-232C input socket / D-Sub 9-pin male
Set ID / Communication Parameters
Command Reference List
Transmission/Receiving Protocol
38
Programming the Remote
Programming Codes
Troubleshooting check list
42
Monitor Specification
RGB Mode / DVI Mode
2
28
43
47
Installation
Power
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set.
In the event of thunderstorms or powercuts, please pull out the aerial and mains plugs.
a. Open the back panel cover.
b. After connecting the power cord to the set, connect the power
cord to an AC mains.
c.
Fix cables with the supplied cable tie after collecting connected
cables.
d. Pull the cables through the hole on the set.
e. Close the back panel cover.
a/e
Warning
To
prevent fire
shock hazard, do not expose the set to rain or moisture. Do not rub or strike the Active Matrix LCD with anything hard as
this may scratch, mar, or damage the Active Matrix LCD permanently.
or
Service
Never
the back cover of the set as this can expose you to
high voltage and other hazards. If the set does not operate properly, unplug it and call your dealer.
remove
b
Aerial
Connect the aerial cable to the socket marked +75 Ω on the back.
For the best reception an outdoor aerial should be used.
Location
Position your set so that no bright light or sunlight falls directly onto
the screen. Care should be taken not to expose the set to any
unnecessary vibration, moisture, dust or heat. Also ensure that the
set is placed in a position to allow a free flow of air. Do not cover
the ventilation openings on the back cover.
If you intend to mount the TV to a wall, attach VESA standard mounting interface (optional parts) to the back of the TV. When you install
the set to
fully
so as
use
the wall
not to
mounting
bracket
(optional parts),
fix it
d
care-
drop.
Cleaning
the set before cleaning the face of the LCD Screen. Dust
the set by wiping the screen and the cabinet with a soft, clean cloth.
If the screen requires additional cleaning, use a clean, damp cloth.
Do not use liquid cleaners or aerosol cleaners.
Unplug
On
Disposal
The fluorescent lamp used in this product contains a small amount
of mercury.
Do not dispose of this product with general household waste.
Disposal of this product mute be carried out in accordance to the
regulations of your local authority.
3
Location and function of controls
All the functions
Some functions
panel
can
can
be controlled with the remote control.
also be
adjusted
with the buttons
on
the side
of the set.
Remote Control
1.
POWER
Switches the set
2.
TV/AV
POWER
2
ARC
INPUT
from
standby
or
off to
standby.
TV, AV, S-Video, Component1, Component2,
RGB PC, DVI PC modes.
switches the set on from standby.
1
MODE
TV/AV
Selects
on
3.
MUTE
34
INPUT
Selects
TV, AV, S-Video, Component1, Component2,
RGB PC, DVI PC modes.
5
LIST
Q.VIEW
4.
ARC
5.
NUMBER BUTTONS
Switches the set on from
6
PSM
87
6.
SSM
VOL
or
directly
select
a
number.
the programme table.
7.
PSM (Picture Status Memory)
Recalls your preferred picture setting.
8.
VOLUME UP/DOWN
TEXT
MENU
standby
LIST
Displays
PR
PIP/POP/PBP
(Aspect Ratio Control)
Changes the picture format.
EXIT
9
Adjusts the volume.
Programme UP/DOWN
Selects
a
MENU
Selects
a menu.
OK
10
9.
PIP PR-
10.
PIP INPUT
PIP PR+
SWAP
/
Selects
/
Adjusts
PLAY
11
REW
PAUSE
STOP
FF
RECORD
programme.
(Up/Down/Left/Right) BUTTONS
/
a menu
menu
item.
settings.
OK
Accepts
SKIP
your selection
or
displays
the current mode.
11. VCR/DVD BUTTONS
12
Control
WIN.SIZE
WIN.POSITION
SLEEP
REVEAL
SIZE
UPDATE
I/II
("RECORD"
HOLD
?
MIX
TIME
INDEX
i
MODE
M
some
13
12. SLEEP
Sets the
video
cassette
recorders
button is not available for DVD
sleep
timer.
13. TELETEXT BUTTONS
(option)
These buttons are used for teletext.
For further details, see the 'Teletext' section.
* : No function
(With TELETEXT)
4
or
DVD
player).
player
Location and function of controls
14. MODE
Selects the remote
STB
or
operating mode: TV, VCR, DVD, CABLE,
Select other operating modes, for the remote to
AUDIO.
operate external devices.
15. MUTE
Switches the sound
on or
off.
16. Q.VIEW
Returns to the
Selects
a
viewed programme.
previously
favorite programme.
14
17. SSM (Sound Status Memory)
Recalls your preferred sound setting.
MODE
TV/AV
18. PIP BUTTONS
PIP/POP/PBP
ARC
INPUT
Switches the sub
picture
select
PIP, POP, PBP
PIP PR +/Selects a programme for the sub
or
POWER
MUTE
15
off modes.
picture.
SWAP
Alternates between main and sub
PIP INPUT
Selects the
input
picture.
mode for the sub
LIST
16
picture.
PSM
WIN.SIZE
Adjusts
the sub
picture
SSM
VOL
size.
WIN POSITION
Moves the sub picture to
Q.VIEW
/
or
/
direction.
17
PR
PIP/POP/PBP
*
MENU
EXIT
19. EXIT
18
13
19
Exits from each mode.
20. I/II
Selects the
language during
Selects the sound
dual
language
broadcast.
OK
output.
Note: In teletext mode, the PIP PR -/+, SWAP and PIP INPUT buttons are used for teletext function.
PIP PR-
PLAY
REW
WIN.SIZE
Installing
?
Open
PIP INPUT
PIP PR+
SWAP
PAUSE
STOP
FF
WIN.POSITION
18
RECORD
SKIP
SLEEP
I/II
20
Batteries
the
battery compartment
cover on
two 1.5V AA size batteries in correct
?
Don't mix old
?
Close the
or
used batteries with
the back side and insert
polarity (+
with +,
-
with
-).
new ones.
cover.
(Without TELETEXT)
5
Location and function of controls
Front / Side
panel
PR
6
VOL
5
OK
4
MENU
3
TV
2
AV
1
/
ON/OFF
8
7
1.
/l
(ON
/
OFF)
Switches the set
2.
6.
on or
off.
programme or a menu item.
Switches the set on from standby.
switches the set
on
from
7.
standby.
(DPM Mode).
a menu.
OK
your selection
or
displays
mode.
6
(Volume Down/Up)
Adjusts the volume.
Adjusts menu settings.
/
standby
mode.
Illuminates green when the set is switched on.
Illuminates amber in RGB PC/DVI PC mode
8.
Accepts
POWER/STANDBY Indicator
Illuminates red in
MENU
Selects
5.
a
TV/AV
TV, AV, S-Video, Component1,
Component2, RGB PC, DVI PC modes
4.
(Programme Up/Down)
Selects
Selects
3.
/
the current
Remote Control Sensor
Location and function of controls
Back
panel
S-VIDEO
RAUDIOL/MVE
S-VDEO
MOLVDE
L/
AUDIO
R
A3
8
AV
COMPONENT1
RS-232C
OUT
DVI PC
REMOTE
AC IN
RGB PC
AV
OUT
COMPONENT2
PC AUDIO IN
(480i/576i)
CONTROL
LR
ANT IN
VIDEO
LR
AUDIO
RS 232C
VIDEO IN
N
2
1
3
AUDIO IN
5
4
7
6
1.
POWER CORD SOCKET
6.
AV OUT SOCKETS
2.
REMOTE CONTROL JACK
7.
AERIAL SOCKET
Connect the RF socket of the VCR to the
3.
RS-232C SERIAL PORTS
4.
DVI
(Digital
Visual
Interface) PC / RGB PC /
ial socket.
8.
AUDIO/VIDEO IN SOCKETS (AV)
PC AUDIO IN SOCKETS
Connect the audio/video out sockets of exter-
Connect the set
nal
output socket of the PER-
SONAL COMPUTER to this socket.
equipment
to these sockets.
S-VIDEO/AUDIO IN SOCKETS
Connect the video out socket of
5.
aer-
(SAV)
an
COMPONENT1(DTV, DVD), COMPONENT2
(DVD) IN SOCKETS
VCR to the S-VIDEO socket.
Connect the audio/video out sockets of external
VIDEO VCR to the audio sockets
equipment
S-VIDEO
Connects the audio out sockets of the Sas
in AV.
to these sockets.
7
Basic
Operation
On and off
Press the main power button to switch the set on.
If the set is in standby mode, press the POWER, TV/AV,
/
INPUT, or NUMBER buttons on the remote control to switch it
1.
2.
,
on
fully.
3.
Press the POWER button on the remote control.
The set reverts to standby mode.
4.
Press the main power button
again
to switch the set off.
Note : If, while the set is switched on, the mains plug is disconnected the set will switch to standby or power on when the mains
plug is replaced in the mains power socket.
POWER
MUTE
INPUT
Programme
selection
You
a
can
select
programme number with the
/
or
NUMBER
buttons.
Q.VIEW
Volume
adjustment
Press the
button to
/
SSM
adjust
the volume.
Quick view
Press the Q.VIEW button to view the last programme you
MENU
were
watching.
Note
This function works only when Favourite programme is
set to Off Otherwise each press of this button will select a stored
favourite programme.
OK
:
.
PIP INPUT
Mute function
SWAP
Press the MUTE button. The sound is switched off and the
appears.
You can cancel it
On
screen
by pressing
language
the
/
MUTE,
selection
,
I/II
or
display
SSM button.
(option)
I/II
The
menu
can
be
guage. First select
1.
2.
displayed on the
your language.
screen
Press the MENU button and then
SPECIAL menu.
Press the
button and then
in your desired lan-
button to select the
/
/
button
to
select
Language.
3.
Press the
button and then the
/
button to select your
desired
All the
4.
8
language.
on screen displays
will appear in the selected
Press the MENU button to
save.
language.
On Screen Menus
The
an
dialogue
operator
between you and your set takes
place
on screen
with
menu.
Menu selection
Press the MENU button and then
1.
/
button to
display
each
menu.
Press the
2.
button and then the
/
button to select
a menu
item.
3.
Repeatedly
viewing.
Note
:
press the MENU button to return to normal TV
In the teletext
mode,
menus are
not
displayed.
STATION
PICTURE
Auto programme
PSM
Manual programme
ACC
Programme edit
XD
Favourite programme
MENU
Prev.
STATION
Prev.
MENU
PICTURE
menu
menu
MENU
PIP/POP/PBP
SOUND
On/Off
SSM
Source
Balance
Size
AVL
OK
SRS WOW
Image
Sound
Position
Swap
MENU
Prev.
PIP/POP/PBP
Prev.
MENU
SOUND
menu
SCREEN
Auto-configure
Input
Clock
Child lock
Off time
Language
On time
Power indicator
Auto off
Clock
Phase
TIMER
SPECIAL
ARC
menu
Position
Transparency
Zoom
Reset
MENU
Prev.
MENU
SCREEN
menu
MENU
Prev.
SPECIAL
menu
TIMER
Prev.
menu
9
STATION Menu
STATION
Auto programme
Manual programme
Programme edit
Favourite programme
china : 200) TV stations can be stored in this set by
programme numbers (0 to 99(only china :0 to 199)). Once you have
preset the stations, you will be able to use the D / E or NUMBER
buttons to scan the stations you programmed.
Stations can be tuned using automatic or manual modes.
to 100
Up
(only
Auto programme
MENU
All stations that can be received are stored by this method. It is recommended that you use auto programme during installation of this set.
Prev.
STATION
tuning
menu
Press the MENU button and then D / E button to select the
STATION menu.
Press the G button and then D / E button to select Auto
1.
2.
Programme.
Press the G button. Select a TV system with the G button and
then D / E button on the System menu;
3.
System
BG
Storage from
I
Start
DK
M
MENU
BG
:
Prev.
(Asia/New Zealand/M.East/Africa/Australia)
(Hong Kong/South Africa)
(East Europe/China/Africa/CIS)
(USA/Korea/Philippines) (option)
I
:
DK :
M
:
Press the OK button.
Press the D / E button to select Storage from. And press the
G button. Select the beginning programme number with the D /
E button or NUMBER buttons on the Storage from menu.
Press the OK button.
Press the D / E button to select Start.
4.
5.
6.
7.
MENU
11
OK
CO5
17%
Press the G button to begin auto programming.
All receivable stations are stored. The station name is stored for
stations which broadcast VPS (Video Programme Service),
PDC (Programme Delivery Control) or TELETEXT data. If no
station name can be assigned to a station, the channel number
is assigned and stored by a number as shown below.
8.
AUSTRALIA
CHINA
ELSE
V/UHF
Cable
V/UHF
Cable
V/UHF
Cable
BG
1~75
2~44
1~69
1~47
1~69
1~47
I
1~69
1~47
1~69
1~47
1~69
1~47
DK
1~69
1~47
1~62
1~41
1~69
1~47
M
2~83
1~71
2~83
1~71
2~83
1~71
To stop auto programming, press the MENU button.
When auto programming is completed, the Programme edit
menu appears on the screen. See the 'Programme edit' section
to edit the stored programme.
9.
10
Repeatedly
viewing.
press the MENU button to return to normal TV
STATION Menu
Manual programme
tuning
STATION
Auto programme
Manual programme
Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign a station
Press the MENU button and then
STATION
/
button to select the
menu.
Press the
2.
Favourite programme
with five characters to each programme number.
name
1.
Programme edit
MENU
Prev.
STATION
button and then
menu
button to select Manual
/
Programme.
Press the
3.
button and then
button to select
/
System
BG
Storage
I
Channel
DK
Name
M
System.
Fine tune
Search
MENU
Select
4.
a
TV
Prev.
system with the
button and then
/
button
on
the
System menu;
BG : (Asia/New Zealand/M.East/Africa/Australia)
I
: (Hong Kong/South Africa)
DK : (East Europe/China/Africa/CIS)
M : (USA/Korea/Philippines) (option)
5.
Press the OK button.
6.
Press the
button to select
/
ton. Select the
button
or
Storage.
And press the G but-
programme number with the
NUMBER buttons on the Storage menu.
beginning
/
Press the OK button.
7.
MENU
System
System
Storage
Storage
1
Channel
Channel
Name
Name
Fine tune
Fine tune
Search
Search
MENU
Prev.
MENU
8.
Press the
/
9.
Press the
button and then
or
can
1
OK
Prev.
button to select Channel.
/
button to select VHF/UHF
Then press the G button.
select the desired channel number with the NUMBER
Cable
You
V/UHF
buttons. If
the Channel
on
possible,
menu.
select the channel number
directly
with the
number buttons. Refer to page 10.
10. Press the OK button.
button to select Search.
11. Press the
/
12. Press the
button.
13. Press the OK button to store it.
14. To store another
15.
Repeatedly
viewing.
station, repeat steps 3
to 12.
press the MENU button to return to normal TV
11
STATION Menu
STATION
Assigning
a
station
name
Auto programme
Manual programme
Programme edit
Favourite programme
1.
2.
the 'Manual programme tuning' steps 1 to 2.
Press the
button and then
button to select Name.
/
Repeat
System
MENU
Storage
Prev.
Channel
STATION
Name
menu
C
01
Fine tune
Search
MENU
Prev.
3.
Press the
button and then
4.
-,thenumber0to9andthealphabetAtoZ.
With the
button you can select in the opposite direction.
Select the position by pressing the
button and then
/
5.
your choice of the second character, and
Press the OK button to store it.
use
the
/
.
You
can use a
blank,
+,
6.
Repeatedly
viewing.
Fine
2.
so on.
press the MENU button to return to normal TV
tuning
Normally
1.
make
fine
tuning
is
only
necessary if
reception
is poor.
the 'Manual programme tuning' steps 1 to 2.
Press the
button and then
/
button to select Fine tune.
Repeat
System
MENU
Storage
Channel
Name
Fine tune
Search
OK
MENU
12
Prev.
3.
Press the
button to fine tune for the best
4.
Press the OK button.
5.
Repeatedly press the MENU button to return to normal TV
viewing.
The finely tuned programme will be indicated by yellow number
during programme selection.
picture
and sound.
STATION Menu
Programme
edit
STATION
Auto programme
This function enables you to delete or skip the stored programmes.
Also you can move some stations to other programme numbers or
copy a blank station data into the selected programme number.
1.
Press the MENU button and then
STATION
2.
Press
Favourite programme
menu.
the
Press the
MENU
button
Programme
3.
Programme edit
button to select the
/
use
Manual programme
and
then
button
/
Prev.
select
to
STATION
edit.
button to
the
display
Programme
edit
menu
menu.
0C051C052C053C05
4-----5-----6-----7----9-
-
-
-
-10C0511C0512C05
13C0514C0515-----16----16-----17-----18-----19----MENU
Deleting
1.
Prev.
Delete
Move
Copy
Skip
a
programme
Select a programme to be deleted with the
/
/
or
but-
ton.
2.
Press the RED button twice.
The selected
grammes
Copying
1.
are
programme is deleted,
shifted up one position.
all the
following
pro-
a
programme
Select a programme to be
with the
copied
/
/
or
but-
ton.
2.
Press the GREEN button.
All the
Moving
1.
following
programmes
are
shifted down
one
position.
a
programme
Select a programme to be moved with the
MENU
/
or
/
but-
ton.
2.
Press the YELLOW button.
3.
Move the programme to the desired programme number with
the
/
or
/
button.
4.
Press the YELLOW button
to release this function.
programme number
Select a programme number to be
Skipping
1.
again
/
a
PIP PR-
skipped
with the
/
or
PIP INPUT
PIP PR+
SWAP
button.
2.
Press the BLUE button. The
3.
Press the BLUE button
skipped programme turns to
again to release the skipped
gramme.
When a programme number is
unable to select it
using
the
/
pro-
that you will be
button during normal TV
skipped
it
blue.
means
If you want to select the skipped programme, directly
enter the programme number with the NUMBER buttons or
viewing.
select it in the programme edit
Repeatedly
or
table
menu.
press the MENU button to return to normal TV
viewing.
13
STATION Menu
Favourite programme
STATION
Auto programme
Manual programme
Programme edit
This function lets you select your favourite programmes
1.
Press the MENU button and then
STATION menu.
2.
Press the
Favourite programme
button and then
/
directly.
button to select the
/
to select Favourite pro-
gramme.
MENU
Prev.
ON
STATION
menu
3.
4.
5.
6.
7.
--
-----
--
-----
--
-----
--
-----
--
-----
--
-----
--
-----
--
-----
Press the
button and then
/
button to select On
Press the
button to select
/
Select a desired programme with the
/
button.
To store another programme, repeat steps 4 to 5.
You can store up to 8 programmes.
Press the MENU button to return to normal TV viewing.
--
or
Off.
-----
.
Repeatedly press
the Q.VIEW button to select stored favourite pro-
grammes.
Calling
You
LIST
Q.VIEW
the programme table
check the programmes stored in the memory
the programme table.
can
Displaying programme
by displaying
table
Press the LIST button to display the Programme table
The programme table appears on the screen.
menu.
PROGRAMME LIST
0C051C052C053C05
MENU
4-----5-----6-----7----9-
-
-
-
-10C0511C0512C05
13C0514C0515-----16----16-----17-----18-----19-----
OK
Note :
a.
You may find some blue highlighted programmes shown. They
have been set up in the programme edit mode.
b. Some programmes with the channel number shown in the programme table indicate there is no station name assigned.
programme in the programme table
Select a programme with the
/
or
/
button.
Then press the OK button.
The set switches to the chosen programme number.
Selecting
a
programme table
10 programme table pages in which contain 199 pro-
Paging through
There
are
grammes.
Pressing the
Repeatedly
14
/
a
or
/
button
repeatedly
turns the pages.
press the MENU button to return to normal TV
viewing.
PICTURE Menu
PSM
Status
(Picture
Memory)
PICTURE
PSM
1.
Press the MENU button and then
ACC
XD
TURE
2.
button to select the PIC-
/
menu.
Press the
button and then
button to select PSM.
/
PICTURE
PSM
Dynamic
ACC
Standard
XD
Mild
MENU
Prev.
PICTURE
Game
menu
User
Prev.
MENU
3.
Press the
ting
4.
on
button and then
the PSM
can
also
a
picture
set-
menu.
Press the MENU button to
You
button to select
/
recall
save.
desired
a
picture (Dynamic, Standard,
User) with PSM button on the remote control. The
picture Dynamic, Standard, Mild and Game are programmed
for optimum picture reproduction at the factory and cannot be
changed.
Mild, Game
Picture
You
adjustment
adjust picture contrast, brightness, colour intensity, sharpand tint (NTSC only) to the levels you prefer.
can
ness
1.
Press the MENU button and then
PICTURE
2.
or
Press the
/
PSM
button to select the
menu.
button and then
/
button to select PSM.
MENU
PICTURE
PSM
Dynamic
ACC
Standard
XD
Mild
Contrast
Game
Brightness
User
Color
Sharpness
Tint
MENU
Prev.
Contrast
100 FG
3.
Press the
button and then
/
4.
Press the
button and then
/
button to select User.
button to select the desired
picture option. (Contrast, Brightness, Color, Sharpness
and
Tint)
5.
Press the
6.
Press the MENU button to
/
button to make
appropriate adjustments.
save.
15
PICTURE Menu
ACC
PICTURE
PSM
To initialize values
ACC
XD
to default
settings),
select the Normal
option.
1.
Press the MENU button and then
PICTURE
MENU
(reset
2.
Prev.
PICTURE
/
button to select the
menu.
Press the
button and then
button to select ACC.
/
PICTURE
menu
PSM
Warm
ACC
Normal
XD
Cool
MENU
3.
Press the
Normal
4.
Prev.
button and then
or
/
button to select
Warm,
Cool.
Press the MENU button to
save.
XD
XD is LG Electronic's
play a real HD
ing algorithm.
XD Demo
1.
-
Use to see the difference between XD Demo On and
XD Demo Off.
Press the MENU button and then
PICTURE
MENU
unique picture improving technology to dissource though an advanced digital signal process-
/
menu.
2.
Press the
button and then
/
button to select XD.
3.
Press the
button and then
/
button to select
XD Demo.
PICTURE
PSM
ACC
Off
XD
On
XD Demo
MENU
4.
16
button to select the
Prev.
Off or On.
Press the EXIT button to stop XD Demo.
Press the MENU button to
save
Off, On
or
SOUND Menu
SSM
(Sound Status Memory)
SOUND
SSM
Balance
You
can
Speech
1.
select your preferred sound setting; Flat, Music, Movie or
and you can also adjust the sound frequency of equalizer.
Press the MENU button and then
SOUND
/
AVL
SRS WOW
button to select the
menu.
MENU
SOUND
Prev.
SOUND
SSM
Flat
Balance
Music
AVL
menu
Movie
SRS WOW
Speech
User
MENU
Prev.
2.
Press the
button and then
3.
Press the
button and then
ting
on
Sound
the SSM
button to select SSM.
/
button to select
/
a
sound set-
menu.
Frequency Adjustment
Press the OK button in User.
a.
Equalizer
0.1
0.5
1.0
5 .0
10.0
Khz
Prev.
MENU
b. Select
a
sound band
Make
SSM
by pressing
the
/
button.
button.
/
appropriate
d. Press the OK button to store it for the sound User.
c.
4.
You
sound level with the
Press the MENU button to
can
also recall
a
MENU
save.
desired sound
setting (Flat, Music, Movie,
Speech or User) with SSM button
sound settings Flat, Speech, Movie
for optimum sound reproduction at
changed.
on
the remote control. The
and Music
the
OK
factory
are
programmed
and cannot be
If you press the SSM button after making appropriate adjustment on the User sub menu, the display User automatically
Note
:
appears
even
though
Flat, Music, Movie
you have
already set a factory preset setting;
or Speech.
17
SOUND Menu
SOUND
SSM
Sound
You
adjustment
adjust balance, AVL (Auto
ically keeps on an equal volume
Balance
AVL
SRS WOW
can
Volume Leveler). AVL automatlevel even if you change pro-
grammes.
1.
Press the MENU button and then
SOUND menu.
/
button to select the
SOUND
MENU
Prev.
SOUND
menu
SSM
Off
Balance
On
AVL
SRS WOW
MENU
2.
Prev.
Press the
button and then
button to select the desired
/
sound item; Balance or AVL
and then
Balance: Make desired adjustment with the
/
press the OK button.
AVL : Press the
/
button to select Off or On.
Press the MENU button to save.
.
3.
4.
SRS WOW
The SRS WOW function plays back the mono or stereo sound input
with the dynamic surround effects. It will provide rich and profound
sound tone. If you set the SRS WOW on, user audio setting can not
be adjusted.
1.
Press the MENU button and then
SOUND
2.
MENU
/
button to select the
menu.
Press the
button and then
/
button to select SRS WOW.
SOUND
SSM
Off
Balance
On
AVL
SRS WOW
OK
MENU
3.
Press the
button and then
4.
Press the MENU button to
is
a
is
/
button to select Off
or
On.
save
trademark of SRS
technology
18
Prev.
Labs, Inc.
incorporated
under license from SRS
Labs, Inc.
SOUND Menu
Stereo/Dual
reception
SOUND
SSM
When a programme is selected, the sound information for the station appears after the programme number and station name disap-
Balance
AVL
SRS WOW
pear.
Broadcast
On Screen
Mono
MONO
Stereo
STEREO
Dual
DUAL I
Display
MENU
Prev.
SOUND
menu
Mono sound selection
In stereo reception if the stereo signal is weak, you can switch to
mono by pressing the I/II button twice. In mono reception the depth
of sound is improved. To switch back to stereo, press the I/II button
twice again.
selection for dual language broadcast
If a programme received in two languages (dual language), you can
switch to DUAL I, DUAL II or DUAL I+II by pressing the I/II but-
Language
ton
repeatedly.
DUAL I sends the
primary
broadcast
to the
language
loudspeak-
ers.
DUAL II sends the
secondary
broadcast
language
to the loud-
speakers.
DUAL I+II sends
NICAM
separate language
a
to each
loudspeaker.
reception
If your set is
equipped
with the receiver for NICAM
reception, the
Companding Audio
high quality NICAM (Near Instantaneous
Multiplex) digital sound can be received.
Sound output can be selected according to the type of received
broadcast as follows by pressing the I/II button repeatedly.
1.
2.
3.
When
NICAM
mono
is
received, you
select NICAM
can
MONO or FM MONO.
When NICAM stereo is received, you can
STEREO or FM MONO. If the stereo signal is
FM mono.
When NICAM dual is received, you can select
I, NICAM DUAL II or NICAM DUAL I+II or
select NICAM
weak, switch to
NICAM DUAL
MONO.
Sound output selection
In Component1, Component2 mode, you
the left and right loudspeakers.
can
select
output sound for
I/II
press the I/II button to select the sound output.
Audio signal from audio L input is sent to the left loud
speaker and audio signal from audio R input is sent to the
right loud speaker.
Audio signal from audio L input is sent to left and right loud-
Repeatedly
L+R
:
L+L
:
R+R
:
speakers.
Audio signal
speakers.
from audio R
input
is sent to left and
right
loud-
19
TIMER Menu
Clock
TIMER
Clock
You must set the time
Off time
correctly
before
on/off time function.
using
On time
1.
Auto off
2.
Press the MENU button and then
TIMER menu.
Press the
button and then
/
button to select the
/
button to select Clock.
TIMER
MENU
Prev.
Clock
TIMER
Off time
menu
Time
On time
:56
1
:
AM
Auto off
Prev.
MENU
3.
4.
5.
6.
Press
Press
Press
Press
the
button and
the
button and
the
button and
the MENU button
then
then
then
to
button to adjust the hour.
button to adjust the minute.
button to select AM or PM.
/
/
/
save.
On/Off time
The off timer
set time.
1.
2.
automatically
switches the set to
standby
at the pre-
Press the MENU button and then
/
button to select the
TIME menu.
Press the
button and then
/
button to select Off time or
On time.
TIMER
Clock
Off time
Time
On time
__
Auto off
__
:
Pr.
Volume
__
AM
__
__
__
__
__
Off
MENU
MENU
OK
3.
4.
5.
Press the
Press the
Press the
Prev.
button and then
button and then
button and then
/
/
/
button to adjust the hour.
button to adjust the minute.
button to adjust the morn-
ing(AM)or afternoon(PM).
6.
7.
8.
Press the
button and then
/
button to select On or Off.
To cancel Off/On time function, press the
/
button to
select Off.
button and then
/
Only On Time function: Press the
button to select the programme at turn-on and then press the
button and then
/
button to adjust volume level.
Press the MENU button to save.
Note :
In the event of power interruption (disconnection or power faila.
ure), the clock must be reset.
b. Two hours after the set is switched on by the on time function it
will automatically switch back to standby mode unless a button
has been pressed.
c.
Once the on or off time is set, these functions operate daily at
the preset time.
d. Off Time function overrides On Time function if they are set to
the same time.
e.
The set must be in standby mode for the On Time to work.
20
TIMER Menu
Auto off
TIMER
Clock
Off time
If you select On on the Auto off menu, the set will automatically
switch itself to standby mode approximately ten minutes after a TV
station
1.
On time
Auto off
stops broadcasting.
Press the MENU button and then
TIMER menu.
2.
Press the
button and then
/
3.
Press the
button and then
/
/
button to select the
MENU
button to select Auto off.
button to select Off or On.
Prev.
TIMER
menu
TIMER
Off
Clock
On
Off time
On time
Auto off
MENU
4.
Prev.
Press the MENU button to
Sleep
save.
timer
You don't have to remember to switch the set off before you go to
sleep. The sleep timer automatically switches the set to standby
after the
preset time has elapsed.
Press the SLEEP button to select the number of minutes. The dis-
play
'
0 MIN' will appear
60, 90, 120,
the screen, followed by 10, 20, 30,
180 and 240. The timer begins to count down from the
on
number of minutes selected.
Note
a.
:
To view the
remaining sleep
time, press the SLEEP button
MENU
once.
b.
To cancel the
until the
c.
sleep time, repeatedly press
0 MIN' appears.
display
the SLEEP button
'
When you switch the set off, the set releases the preset
time.
sleep
OK
SLEEP
21
SPECIAL Menu
Main Picture Source Selection
SPECIAL
Input
Child lock
Inputs
Language
Power indicator
RGB
Transparency
TV, AV, S-Video, Component1, Component2,
PC, DVI PC mode. AV mode is used when
recorder
Zoom
be set for
can
(VCR),
or
other
a
video cassette
is connected to the set.
equipment
Reset
MENU
Note
Prev.
SPECIAL
menu
:
When
a
VCR is connected via the aerial socket the set is
used in TV mode. See the 'Connection of external
equipment' sec-
tion.
1.
Press the MENU button and then
SPECIAL
2.
3.
button to select the
/
menu.
Press the
button and then
button to select
/
Input.
Press the
button and then
button to select TV, AV, S-Video,
/
Component1, Component2, RGB PC, DVI PC.
SPECIAL
TV
TV/AV
Input
AV
Child lock
S-Video
Language
Component1
Power indicator
Component2
Transparency
RGB PC
Zoom
DVI PC
Reset
MENU
Prev.
AV: VCR connected to the RCA
jack
on
the side
panel.
S-Video: S-VIDEO VCR connected to the S-VIDEO sockets
on
the side
panel set
Component1: DTV
connected to the
Component
DVD connected to the
Component
1 sockets
on
the back of set.
Component2:
sockets
MENU
on
(480i, 576i)
the back of set.
RGB PC: PC connected to the RGB socket
DVI PC: PC connected to the DVI socket
4.
2
Press the MENU button to
on
on
the set
the set
save.
OK
You
Inputs can be
Component1, Component2, RGB PC,
can
select
the
set
for
TV, AV, S-Video,
DVI PC mode
by pressing
the TV/AV button.
In
AV, S-Video, Component1, Component2, RGB PC, DVI PC
or NUMBER buttons to return to TV mode.
/
mode, press the
22
SPECIAL Menu
Child lock
SPECIAL
The TV can be set so that the remote control handset is needed to
control it. This feature can be used to prevent unauthorized viewing.
Input
Child lock
Language
Power indicator
1.
2.
Press the MENU button and then
SPECIAL menu.
Press the
button and then
/
lock.
button to select the
/
Transparency
Zoom
button to select Child
Reset
MENU
SPECIAL
Prev.
SPECIAL
menu
Input
Child lock
Off
Language
On
Power indicator
Transparency
Zoom
Reset
Prev.
MENU
3.
4.
button to select Off
Press the
button and then
/
Press the MENU button to save.
or
On.
With the lock on, the display Controls locked appears on the
screen if any button on the side panel is pressed while viewing the
TV.
Power indicator
Use this function to set the power indicator on the front side of the
TV to ON or OFF. If you set OFF, it will go off after 15 seconds. If
you set ON at any time, the power indicator will
turned on.
1.
Press the MENU button and then
SPECIAL menu.
2.
Press the
3.
indicator.
Press the
button and then
/
Press the MENU button to save.
4.
button and then
automatically
be
button to select the
/
button to select Power
/
MENU
button to select Off
or
On.
Transparency
To
1.
adjust
the
menu screen.
Press the MENU button and then D / E
SPECIAL
2.
transparency of the OSD
Press
button to select the
menu.
the
G
button
and
D
then
/
E
button
to
select
Transparency.
SPECIAL
Input
Child lock
Language
0
Power indicator
Transparency
Zoom
Reset
MENU
3.
4.
Press the
button and then press the
F
/ G
button to make
appropriate adjustments.
Press the MENU button to
Note :
The
.
Prev.
adjustment
range of
save.
Transparency is
0~100.
23
SPECIAL Menu
Picture Size Zoom
SPECIAL
Input
Use this function to
Child lock
in the
zoom
When you turn the TV off and
be restored.
Language
Power indicator
screen.
on
again,
the default
screen
size will
Transparency
1.
Zoom
Reset
MENU
Press the MENU button and then D / E
SPECIAL
2.
Prev.
SPECIAL
button to select the
menu.
Press the G button and then D / E
button to select Zoom
.
menu
SPECIAL
Zoom
0
Input
H Position
0
Child lock
V Position
0
Language
Power indicator
Transparency
Zoom
Reset
Prev.
MENU
3.
Press the G button
and then D / E
Press the F / G button to
4.
Press the D / E
5.
button to to
:
If the
zooming
tioning
reduce the
adjust
the
or
picture
size.
V Position.
picture position
while in
mode.
Press the MENU button to
Note
or
button to select H Position
Press the F / G
larged picture
enlarge
button to select Zoom.
save.
value is set to '0', vertical and horizontal posi-
cannot be
adjusted.
Reset
MENU
Use this function to reset the set to the
language
1.
factory
default.
However,
selection will not be initialized.
Press the MENU button and then
/
button to select the
SPECIAL menu.
2.
Press the
button and then
button to select Reset.
/
SPECIAL
Input
Child lock
To set
Language
Power indicator
Transparency
Zoom
Reset
MENU
3.
Press the
button to start Reset.
4.
Repeatedly
viewing.
press the MENU button to return to normal TV
Note
24
Prev.
:
This function operates in every mode.
SCREEN Menu
Picture format
SCREEN
ARC
You can watch TV in various
Zoom1 and Zoom2.
picture formats; Full, 4:3, Spectacle,
Auto-configure
Clock
Phase
1.
2.
Press the MENU button and then
SCREEN menu.
Press the
button and then
/
/
button to select the
Position
button to select ARC.
MENU
Prev.
SCREEN
Full
ARC
4:3
Auto-configure
Spectacle
Clock
Zoom1
Phase
Zoom2
SCREEN
menu
Position
MENU
3.
4.
Prev.
Press the
button and then
desired picture format.
Press the MENU button to save.
/
button
You can also select Full, 4:3, Spectacle, Zoom1
the ARC button on the remote control.
to select your
or
Zoom2 with
ARC
Full
When your TV receives the wide screen signal, it will lead you to
adjust the picture horizontally or vertically, in a linear proportion, to
fill the entire screen fully.
4:3
It will lead you to view a picture with an original 4:3 aspect ratio,
with gray bars appearing at both the left and right sides.
Spectacle
When your TV receives the wide screen signal, it will lead you to
adjust the picture horizontally, in a linear proportion, to fill the entire
screen.
MENU
Zoom1
Choose Zoom1 when you want to view the picture without any
alteration. However, the top and bottom portions of the picture will
be cropped.
Zoom2
Choose Zoom2 when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade
off between alteration and screen coverage.
Note :
In PIP/POP/PBP mode, ARC function isn't available.
a.
b. In RGB, DVI modes, you can only select 1:1 and Full
screen.
25
SCREEN Menu
Auto
SCREEN
adjustment (RGB [PC]
mode
only)
ARC
Auto-configure
and minimizes
Automatically adjusts picture position
Clock
image shaking.
Phase
1.
Position
Press the MENU button and then
SCREEN
MENU
2.
Prev.
button to select the
/
menu.
Press the
button and then
button to select Auto
/
-
Configure.
SCREEN
menu
SCREEN
ARC
To Set
Auto-configure
Clock
Phase
Position
Prev.
MENU
3.
Press the
button to start
Auto-configure.
image is still not correct, try
If the
4.
position of the
ment again.
Repeatedly press the
viewing.
Clock and Phase
If the
picture
are
correct the
screen
2.
MENU button to return to normal TV
(RGB [PC]
mode
Press the
only)
still
adjustment and especially that
trembling, adjust the picture phase manually. To
size, adjust Clock.
Press the MENU button and then
SCREEN
MENU
adjust-
isn't clear after auto
characters
1.
Auto
/
button to select the
menu.
button and then
button to select Clock
/
or
Phase.
3.
Press the
button and then press the
appropriate adjustments.
SCREEN
ARC
Auto-configure
50
Clock
Phase
Position
MENU
4.
Press the MENU button to
Note
26
Prev.
save.
:
a.
The
b.
The
adjustment
adjustment
range of Phase is 0~100.
range of Clock is 0~100.
/
button to make
SCREEN Menu
SCREEN Position
(RGB [PC]
mode
only)
SCREEN
ARC
Auto-configure
1.
Press the MENU button and then
SCREEN
2.
Press the
button to select the
/
Clock
Phase
menu.
Position
button and then
/
button to select Position.
SCREEN
MENU
ARC
Prev.
Auto-configure
SCREEN
Clock
menu
Phase
Position
MENU
3.
Press the
position
4.
Horizontal
50
Vertical
47
Prev.
button and then
/
or
/
button until desired
is achieved.
Press the MENU button to
save.
MENU
27
PIP/POP/PBP
PIP/POP/PBP
On/Off
PIP/POP/PBP mode
1.
Source
Size
2.
Image
operation
Sound
Press the MENU button and then
button to select the
/
PIP/POP/PBP menu.
Press the
button and then
button to select On/Off.
/
PIP/POP/PBP
Position
Swap
MENU
On/Off
Off
Source
PIP
Size
POP
Image
PBP
Prev.
PIP/POP/PBP
menu
Sound
Position
Swap
MENU
3.
4.
Prev.
Press the
button and then
/
POP or PBP.
Press the MENU button to save.
button to select
Off, PIP,
PIP
After
the
selecting PIP
following menu
in the PIP On/Off menu,
items can be adjusted.
POP
After
selecting POP
menu, the following
adjusted.
in the POP On/Off
menu
items
can
be
PBP
After
selecting PBP
menu, the following
adjusted.
PIP/POP/PBP
You can also select PIP, POP, PBP
button on the remote control.
or
in the PBP On/Off
menu items can be
Off with the PIP/POP/PBP
MENU
Sub Picture Size
To
OK
adjust the size of the
Large / PBP : Full, 4:3)
1.
2.
3.
PIP/PBP
screen.
(PIP: Small, Medium,
Press the MENU button and then
button to select the
/
PIP/POP/PBP menu.
Press the
button and then
button to select Size.
/
Press the
button and then
button to adjust the sub pic/
ture size.
PIP/POP/PBP
On/Off
Small
Source
Medium
Size
Large
Image
Sound
Position
WIN.SIZE
Swap
MENU
Prev.
Press the MENU button to save.
You can also adjust this function with the WIN.SIZE button
remote control.
4.
28
on
the
PIP/POP/PBP
operation
Source
PIP/POP/PBP
On/Off
Source
To select
Inputs
RGB
an
can
input signal
be set for
for PIP/POP/PBP.
Size
TV, AV, S-Video, Component1, Component2,
PC, DVI PC mode. AV mode is used when
recorder
(VCR),
other
or
a
video cassette
is connected to the set.
equipment
Image
Sound
Position
Swap
MENU
Note
:
When
VCR is connected via the aerial socket the set is
a
used in TV mode. See the 'Connection of external
equipment' sec-
Prev.
PIP/POP/PBP
menu
tion.
1.
Press the MENU button and then
PIP/POP/PBP
2.
Press the
/
button to select the
menu.
button and then
button to select Source.
/
PIP/POP/PBP
On/Off
TV
Source
AV
Size
S-Video
Image
Component1
Sound
Component2
Position
RGB PC
Swap
DVI PC
MENU
3.
Press the
Prev.
button and then
/
button to select
TV, AV, S-Video,
Component 1, Component 2, RGB PC, DVI PC.
AV: VCR connected to the RCA jack on the side panel.
S-Video: S-VIDEO VCR connected to the S-VIDEO sockets
on
the back
panel set
Component1: DTV
connected to the
Component 1
sockets
on
DVD connected to the
Component 2
sockets
on
the back of set.
Component2:
MENU
the back of set.
RGB PC: PC connected to the RGB socket
DVI PC: PC connected to the DVI socket
4.
Press the MENU button to
on
the set
OK
Support>
TV
AV
TV
X
X
X
X
X
AV
X
X
X
X
X
S-Video
X
X
X
X
X
COMPONENT 1
X
X
X
X
X
COMPONENT 2
X
X
X
X
X
Sub-Screen
the set
save.
<Table of PIP/POP/PBP Function
Main Screen
on
S-Video COMPONENT1 COMPONENT2 RGB-PC
DVI-PC
X
RGB-PC
DVI-PC
You
can
also
PIP INPUT
X
adjust
this function with the PIP INPUT button
on
the
remote control.
29
PIP/POP/PBP
PIP/POP/PBP
operation
Image
On/Off
To
Source
adjust
Image
Sound
2.
Position
image
of the PIP/POP/PBP
Swap
MENU
screen.
Press the MENU button and then
button to select the
/
PIP/POP/PBP menu.
Press the
button and then
button to select Image.
/
1.
Size
the
PIP/POP/PBP
Prev.
PIP/POP/PBP
menu
On/Off
Contrast
100
Source
Brightness
64
Size
Color
64
Image
Tint
50
Sound
Position
Swap
MENU
Prev.
Press the
button and then
button to select Contrast
/
Brightness,Color or Tint (NTSC only).
Press the
/
button to make appropriate adjustments
Press the MENU button to save.
3.
4.
5.
Note
:
When PIP
input
source,
only Color
,
and Tint is TV mode.
Sound
To turn the PIP/POP/PBP sound on/off
Press the MENU button and then
button to select the
/
PIP/POP/PBP menu.
Press the
button and then
button to select Sound.
/
1.
2.
PIP/POP/PBP
On/Off
Off
Source
On
Size
Image
Sound
Position
Swap
MENU
MENU
Press the
button and then
/
Press the MENU button to save.
3.
4.
Moving
To
Prev.
adjust
1.
2.
button to select Off
or
On.
the sub Picture
the
position
to PIP
screen.
Press the MENU button and then
button to select the
/
PIP/POP/PBP menu.
Press the
button and then
button to select Position.
/
PIP/POP/PBP
On/Off
Source
Size
Image
Sound
Position
Swap
3.
4.
Press the
button and then
/
tion is achieved.
The sub picture moves up/down or
Press the MENU button to save.
button until desired
left/right.
also adjust this function with WIN.POSITION button
remote control.
You
30
can
posi-
on
the
PIP/POP/PBP
operation
Swap
PIP/POP/PBP
On/Off
To switch the main-screen and sub-screen in PIP/POP/PBP mode.
Source
Size
Press the MENU button and then
PIP/POP/PBP menu.
1.
/
button to select the
Image
Sound
Position
Swap
PIP/POP/PBP
To set
On/Off
MENU
Prev.
Source
Size
PIP/POP/PBP
menu
Image
Sound
Position
Swap
MENU
button to select Swap.
/
Press the
button to switch the main-screen and sub-screen.
Press the MENU button to save.
2.
Press the
Prev.
3.
4.
button and then
SWAP
PIP
SWAP
POP
SWAP
PBP
MENU
Press the SWAP button to
Programme
The sub
exchange
selection for sub
the main and sub
pictures.
picture
programme selection is available when the sub picture is TV mode. Press the PIP PR -/+ buttons to select a programme for the sub picture.
picture
PIP PRPIP PR+
SWAP
31
Teletext
Teletext
(option)
TOP
(or
with the teletext
Teletext is
a
text)
is
system
an
can
optional function,
grammes, share
information
prices
on
by
most TV stations which
a
set
can
gives
weather, television pro-
news,
and many other
The teletext decoder of this TV
FASTEXT
only
receive the teletext broadcast.
free service broadcast
up-to-the-minute
therefore
topics.
support the SIMPLE, TOP and
systems. SIMPLE (standard teletext) consists of
a num-
ber of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern
methods
allowing quick
and easy selection of teletext information.
Switch on/off
Press the TEXT button to switch to teletext.
The initial page or last page appears on the screen.
Two page numbers, TV station name, date and time
on
the
tion,
are
displayed
headline. The first page number indicates your selecwhile the second shows the current page displayed.
screen
Press the TEXT button to switch off teletext. The
mode
previous
reappears.
TEXT
SIMPLE text
MENU
Page
1.
selection
Enter the desired page number as a three digit number with the
NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then reenter the correct page number.
2.
The
lowing
button
/
can
be used to select the
preceding
or
fol-
page.
colour button in LIST mode
If the TV is in SIMPLE text, TOP text or FASTEXT mode, press the
M button to switch to LIST mode.
Programming
a
Four teletext page numbers of your choice can be colour coded and
easily selected by pressing the corresponding coloured button on
the remote control.
1.
Press
a
2.
Using
the NUMBER
3.
gramme.
Press the OK button. The selected page is stored as the selected page number, blinking once to confirm this. From now on,
MODE
M
4.
32
coloured button.
buttons, select the page you wish
you can select this page with the
The three other coloured buttons
same
are
to pro-
coloured button.
programmed
in this way.
Teletext
TOP text
The
user
(option)
(option)
guide displays
the bottom of the
four
fields-red, green, yellow and blue
field denotes the next group
and the blue field indicates the next block.
screen.
The
at
yellow
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the yellow button to proceed to the next group with automatic overflow to the next block.
3.
With the green button you can proceed to the next
page with automatic overflow to the next group.
Alternatively
4.
The
red
the
button
button
Alternatively
can
to
permits
the
button
can
existing
be used.
return
to
previous
selection.
be used.
Direct page selection
Corresponding to the SIMPLE teletext mode, you can select a page
by entering it as a three digit number using the NUMBER buttons in
TOP mode.
FASTEXT
The teletext pages are colour coded along the bottom of the screen
and are selected by pressing the corresponding coloured button.
Page
selection
1.
Press the
2.
You
can
button to select the index page.
select the pages which are colour coded
i
tom line with the
same
along
the botPIP PR-
coloured buttons.
PIP INPUT
PIP PR+
3.
Corresponding to the SIMPLE
page by entering its three digit
teletext
mode, you
can
select
SWAP
a
page number with the NUMBER
buttons in FASTEXT mode.
4.
The
lowing
/
button
can
be used to select the
preceding
or
fol-
page.
INDEX
i
33
Teletext
Special
(option)
teletext functions
REVEAL
Press this button to
display concealed information, such as
solutions of riddles or puzzles.
Press this button again to remove the information from the
display.
SIZE
Selects double
Press
Press
height text.
this button to enlarge the top
this button again to enlarge
page.
Press this button
half of the page.
the bottom half of the
to return to the normal
again
display.
UPDATE
Displays
the TV
picture
teletext page. The
left hand corner of the
new
available then
on
the
screen
waiting
for the
will appear at the top
When the updated page is
display
screen.
will
display
while
change
to the page
num-
ber.
Press this button to view the
updated
teletext page.
HOLD
the automatic page
text page consists of 2 or
Stops
which will
change
occur
if
a
tele-
sub pages. The number of
sub pages and the sub page displayed is, usually, shown
on the screen below the time. When this button is pressed
OK
PIP INPUT
SWAP
more
the
stop symbol is displayed
the
screen
at the
top left-hand
corner
of
and the automatic page change is inhibited.
To continue press this button again.
MIX
Displays
the teletext pages
superimposed
on
the TV
pic-
ture.
To switch the TV
picture
off press this button
again.
TIME
When
MIX
TIME
TV programme, press this button to display
the time at the top right hand corner of the screen. Press
viewing
this button
a
again
to
remove
mode, press this button
the
to select
display.
In the teletext
sub page number. The
at the bottom of the screen.
a
sub page number is displayed
To hold or change the sub page, press the RED /
or NUMBER buttons.
/
Press this button
34
again
to exit this function.
GREEN,
Connection of external
You
can
connect additional
such
equipment,
as
equipment
VCRs, camcorders
etc. to your set.
Here shown may be somewhat different from your set.
Aerial socket
1.
Connect the RF out socket of the VCR to the aerial socket
on
the back of the set.
2.
Connect the aerial cable to the RF aerial in socket of the VCR.
3.
Store the VCR channel
4.
5.
desired programme number using
the 'Manual programme tuning' section.
Select the programme number where the VCR channel is
stored.
Press the PLAY button
DVD
1.
on a
input
the VCR.
on
VCR
sockets
Connect the DVD
or
output sockets (Y Cb Cr, Y Pb Pr, Y B-Y R-Y
Y PB PR) of the DVD to the COMPONENT 1, 2 IN sockets (Y
PB
PR)
of the set.
Connect the audio cable from the DVD to DVD INPUT AUDIO
sockets of the set.
3. Press the TV/AV or INPUT button to select Component 1, 2.
2.
4.
Press the PLAY button
The DVD
Note
a.
b.
on
the DVD.
playback picture
appears
DTV
DVD
source
on
the
DVD
screen.
Player
:
Component1
Component2
:
:
,
DVD
source.
DTV in sockets
1.
Connect the SET TOP
ets
2.
(Y
PB
PR)
outputs
to the COMPONENT1 IN sock-
of the set.
Connect the audio cable from the SET TOP to the AUDIO sockets of the set.
3.
Press the TV/AV
or
INPUT button to select
Component
1.
Receriver
35
Connection of external
equipment
S-Video/Audio in sockets
S-VIDEO
When
RAUDIOL/MVE
connecting
picture quality will
1.
(S-Video)
S-VIDEO VCR to the S-VIDEO
an
be further
socket, the
improved.
Connect the S-Video socket of the VCR to the S-VIDEO sock-
AV
S-VIDEO VCR
et of the set.
2.
Connect the audio cable from the S-VIDEO VCR to the AV /
3.
AUDIO L/R sockets of the set.
Select S-Video by pressing the TV/AV button
4.
Press the PLAY button
The VCR
on
playback picture
repeatedly.
the VCR.
appears
on
the
screen.
PC in socket
1.
Connect the
signal
cable from the TV
output socket of the PER-
SONAL COMPUTER to the RGB PC IN
or
DVI PC IN socket of
the set.
2.
Connect the audio cable from the PC to the AUDIO INPUT
sockets of the set.
PERSONAL COMPUTER
3.
Press the INPUT
4.
Switch
on
The set
the
can
or
TV/AV button to select RGB PC
PC, and the PC
be
operated
as
screen
appears
the PC monitor.
on
or
DVI PC.
the set.
Apple macintosh, connect the VGA desktop
block (not supplied) from the 3 row 15 pin to 2 row 15 pin with the
signal cable and connect the VGA desktop block to the Macintosh.
Note
:
If you have
an
Audio/Video in sockets
S-VIDEO
1.
RAUDIOL/MVE
AV
Connect the audio/video out sockets of the VCR to audio/video
in sockets of the set.
2.
Press the TV/AV button to select AV.
3.
Press the PLAY button
The VCR
36
playback picture
the VCR.
appears
on
the
screen.
If you have a mono VCR, connect the audio cable from the
VCR to the AUDIO L/MONO socket of the set.
Note
VCR
on
:
Displayable
Monitor
Specification
RGB Mode
MODE
1
Resolution
640x350
Horizontal
Vertical
Frequency
(KHz)
Frequency
(Hz)
31.47
70.80
(Synchronization input
Note
a.
2
720x400
31.47
form
:
separate)
:
If the set is
cold, there may be
when the set is switched
70.80
on.
a
small "flicker"
This is normal,
nothing wrong with the set.
If possible, use the 1,360x768@60Hz video
mode to obtain the best image quality for your
there is
3
4
640x480
5
31.47
59.94
37.50
75.00
43.27
85.00
b.
LCD monitor. If used under the other resolutions,
some scaled or processed pictures may appear
on
6
7
37.88
800x600
8
9
832x624
10
60.32
46.88
75.00
53.67
85.06
49.73
74.55
48.36
60.00
85Hz,
1024x768
12
13
1280x720
14
60.12
75.03
68.68
85.00
44.77
59.86
63.98
60.02
c.
79.98
75.02
16
1360x768
47.72
59.80
17
1600x1200
75.00
60.00
some
If used to PC vertical
noise
can
be
seen
frequency
when PIP is
on.
to
frequency
Some dot defects may appear on the screen,
like Red, Green or Blue spots. However, this
will have no impact or effect on the monitor
performance.
e.
1280x1024
15
screen.
In this case, set the PC vertical
60Hz.
d.
11
the
Do not press the LCD screen with your finger
for a long time as this may produce some temporary distortion effects on the screen.
When the PC
appears on the set, a
message may appear on the screen, and the
message will differ according to the Window
system version (Win98, 2000). If a message
screen
appears click "Next" until the message finishes.
f.
If the message "Out of range" appears on
the screen, adjust the PC as in the
'Displayable
Monitor
Specification' section.
MODE 1~17: D-Sub
MODE 1~14,16: DVI-D
37
External Control Device
Connect the RS-232C input jack to an external control device
system) and control the set's functions externally.
RS-232C
input
(such
Setup
as a
computer
or an
A/V control
socket
Connect the serial port of the control device to the RS-232C jack on the set.
RS-232C connection cables are not supplied with the set.
The set's remote control handset and side panel controls (except main power) will not be functional if the set is controlled by a PC computer or other external device.
1.
2.
3.
D-Sub
9-pin
No.
Pin
1
No connection
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
No Connection
RS-232C
RS-232C
RS-232C
OUTPUT
OUTPUT
OUTPUT
RS-232C
RS-232C
RS-232C
OUTPUT
OUTPUT
OUTPUT
male
name
1
(Receive data)
(Transmit data)
(DTE side ready)
5
(DCE side ready)
(Ready to send)
(Clear to send)
9
6
Set ID
Use this function to
Refer to 'Real Data
specify a monitor ID
Mapping'. See page
number.
40.
SPECIAL
1.
2.
3.
Press the MENU button and then use the
button to select
/
the SPECIAL menu.
Press the
button and then use
button to select Set ID.
/
Press the
button and then use
button to adjust Set ID
/
to choose the desired monitor ID number.
Note
:
The
adjustment
range of Set ID is 0
99.
?
?
*
Baud rate : 9600 bps (UART)
Parity : None
Communication code : ASCII code
Use a crossed (reverse) cable.
38
ID
~
MENU
Communication Parameters
?
Set ID
Data
length : 8
?Stopbit:1bit
?
bits
Prev.
___
___
External Control Device
Setup
Command Reference List
COMMAND 1
COMMAND 2
DATA
(Hexadecimal)
01. Power
k
a
0~1
k
b
0~8
03. Volume Mute
k
e
0~1
04. Volume Control
k
f
0~64
05. Contrast
k
0~64
06.
k
g
h
07. Color
k
i
0~64
08. Tint
k
j
0~64
09.
k
k
0~64
10. PIP/PBP/POP ON/OFF
k
n
0~3
11. PIP Position
k
q
0~3
12. Balance
k
t
0~64
13. ACC
k
u
0~3
14. PIP/PBP/POP SOURCE
k
y
0~8
02.
Input
Select
Brightness
Sharpness
Transmission /
Receiving
0~64
Protocol
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
Transmission
*
[Command1][Command2][ ][Set ID][ ][Data][Cr]
*
*
*
[Command 1]
[Command 2]
[Set ID]
:
:
:
First command. (j or k)
Second command.
You can adjust the set ID to choose
desired monitor ID number in
Special menu. Adjustment range is
1~ 99. When selecting Set ID '0',
every connected TV set is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa
decimal (0x0~0x63) on transmis-
sion/receiving protocol.
*
[DATA]
:
[Cr]
:
*[]
:
*
To transmit command data.
Transmit 'FF' data to read status
of command.
Carriage Return ASCII code
'0x0D'
ASCII code Space (0x20)'
The Monitor transmits ACK (acknowledgement)
based on this format when receiving normal data.
At this time, if the data is data read mode, it indicates present status data. If the data is data write
mode, it returns the data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
*
The Monitor transmits ACK
based
on
this format when
(acknowledgement)
receiving abnormal
data from non-viable functions
or
communication
errors.
Data 1
:
2
:
3
:
Illegal Code
Not supported
Wait
more
function
time
39
External Control Device
01. Power On
(Command
:
04. Volume
a)
Setup
Control(Command
G To control Power On/Off of the Set.
G To control On/Off of the volume.
Transmission
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
[k][f][ ][Set ID][ ][Data][Cr]
Data
0
Power Off
:
1:PowerOn
Data
Min:00H~Max:64H
[a][ ][Set ID][ ][OK][Data][x]
Acknowledgement
G To show the status of Power On/Off.
[f][ ][Set ID][ ][OK][Data][x]
Data
Transmission
[k][a][ ][Set ID][ ][FF][Cr]
0
:
Min:00H~Max:64H
05. Contrast
Power Off
1:PowerOn
G To
adjust
You
Acknowledgement
can
(Command
screen
also
:
g)
contrast.
adjust
the contrast in the Picture
menu.
[a][ ][Set ID][ ][OK][Data][x]
*
f)
(Hexadecimal code)
Acknowledgement
Data
:
Transmission
The Monitor transmits ACK (acknowledgement)
based on this format when receiving normal data.
At this time, if the data is data read mode, it indicates present status data. If the data is data write
mode, it returns the data of the PC computer.
[k][g][ ][Set ID][ ][Data][Cr]
Data
Min:00H~Max:64H
*Refer to 'Real data mapping' as shown below.
Acknowledgement
02.
Input Select (Command
Input)
G To select
You
can
input
source
also select
INPUT button
on
:
b) (Main Picture
[g][ ][Set ID][ ][OK][Data][x]
for the Set.
an
input
source
using
the
06.
Brightness (Command
Transmission
Data0:TV
2:AV
3 : S-Video
4 : Component 1
can
brightness.
adjust the brightness
screen
also
5 : Component 2
6:RGBPC
8:DVIPC
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data Min:00H~Max:64H
Refer to 'Real data mapping' as shown below.
*
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
[h][ ][Set ID][ ][OK][Data][x]
5 : Component 2
6:RGBPC
8:DVIPC
*
Real data
mapping
0:Step0
A:Step10(SETID10)
Mute(Command : e)
F:Step15(SETID15)
10:Step16(SETID16)
G To control On/Off of the Volume Mute.
Transmission
64
[k][e][ ][Set ID][ ][Data][Cr]
*
:
:
Volume Mute On (Volume
Volume Mute Off (Volume
Off)
On)
Acknowledgement
[e][ ][Set ID][ ][OK][Data][x]
Data 0
1
40
:
:
in the Picture
menu.
Acknowledgement
Data0:TV
2:AV
3 : S-Video
4 : Component 1
adjust
You
[k][b][ ][Set ID][ ][Data][Cr]
Data 0
1
h)
the remote control.
G To
03. Volume
:
Volume Mute On (Volume
Volume Mute Off (Volume
Off)
On)
:
Step
100
Tint,Balance
:-50
+50
~
External Control Device
07. Color
G To
(Command
the
also
adjust
You
can
screen
adjust
11. PIP
i) (TV,AV only)
:
color.
the color in the Picture
G To
menu.
Setup
Position(Command
adjust
PIP
Transmission
[k][q][ ][Set ID][ ][Data][Cr]
[k][i][ ][Set ID][ ][Data][Cr]
Data 0
1
2
3
Min:00H~Max:64H
(Hexadecimal code)
:
:
:
:
Bottom of the right side on screen
Bottom of the left side on screen
Top of the left side on screen
Top of the right side on screen
Acknowledgement
Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
[q][ ][Set ID][ ][OK][Data][x]
Data
Data 0
1
2
3
Min:00H~Max:64H
08. Tint
G To
(Command
the
also
j) (TV,AV -NTSC only)
:
adjust
screen
can
adjust
You
tint.
the tint in the Picture
menu.
Red: 00H
Green: 64H
Red: 00H
You
can
the
screen
Balance.
Min:00H~Max:64H
[t][ ][Set ID][ ][OK][Data][x]
Green: 64H
:
k) (TV,AV only)
Sharpness.
adjust the sharpness
screen
in the Picture
menu.
13.
Min:00H~Max:64H
ACC(Command
G To
adjust
the
:
screen
u)
color
[k][u][ ][Set ID][ ][Data][Cr]
[k][k][ ][Set ID][ ][Data][Cr]
Data 0 : Normal (9300K)
2 : Warm (6500K)
PC : 0,2,3,
Min:00H~Max:64H
(Hexadecimal code)
[u][ ][Set ID][ ][OK][Data][x]
[k][ ][Set ID][ ][OK][Data][x]
Data 0 : Normal
2:Warm
Min:00H~Max:64H
14. PIP/PBP/POP
10. PIP/PBP/POP
ON/OFF(Command
:
n)
G To control PIP/PBP/POP On/Off of the Set.
Transmission
[k][n][ ][Set ID][ ][Data][Cr]
Data0:OFF
2:PBP
SOURCE(Command
:
y)
Data0:TV
2:AV
3 : S-video
4 : Component 1
5 : Component 2
6:RGBPC
8:DVIPC
Transmission
1:PIP
3:POP
Acknowledgement
[k][y][ ][Set ID][ ][Data][Cr]
Min:00H~Max:08H
(Hexadecimal code)
[n][ ][Set ID][ ][OK][Data][x]
2:PBP
1:Cool
3:User
G To select the sub-screen source.
Data
Data0:OFF
1 : Cool
3 : User
AV : 0,1,2
Acknowledgement
Acknowledgement
Data
temperature.
Transmission
Transmission
Data
t)
~
Sharpness (Command
the
also
adjust
:
Acknowledgement
Data
adjust
:
(Hexadecimal code)
[j][ ][Set ID][ ][OK][Data][x]
G To
:
Balance(Command
Data
Acknowledgement
09.
:
Bottom of the right side on screen
Bottom of the left side on screen
Top of the left side on screen
Top of the right side on screen
[k][t][ ][Set ID][ ][Data][Cr]
~
(Hexadecimal code)
Data
:
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data
12.
G To
Transmission
q)
position.
Transmission
Data
:
Acknowledgement
1:PIP
3:POP
[y][ ][Set ID][ ][OK][Data][x]
DataMin:00H~Max:08H
41
the Remote
Programming
G The
remote control is
trol. It
can
be
a
multi-brand
programmed
to
universal remote
or
operate
con-
most remote-controllable
devices of other manufacturers.
Note that the remote control may not control all models of
other brands.
Programming
MODE
POWER
MUTE
a
code into
a
remote mode
1. Test your remote control.
To find out whether your remote control
operate the compothe component such as a
nent without
can
programming, turn on
VCR and press the corresponding MODE button (VCR) on the
remote control, while pointing at the component. Test the
POWER and PR +/- buttons to see if the component responds
properly. If not, the remote requires programming to operate the
device.
2. Turn
on
the
PR
component
sponding MODE
button
to be
on
then press the
the remote control.
programmed,
3. Press the MENU and MUTE buttons
MENU
control is
4. Enter
a
ready
can
programmed
code number
Programming
OK
to be
be found
using
simultaneously,
corre-
the remote
for the code.
the number buttons
on
the remote.
code numbers for the
on
the
following
pages.
corresponding component
Again, if the code is correct,
the device will turn off.
5. Press the MENU button to store the code.
6. Test
the
remote
responds properly.
42
control
If not,
functions
to
see
repeat from step
2.
if
the
component
Programming
Codes
VCRs
VCRs
Brand
Codes
Brand
Codes
AIWA
034
KENWOOD
014
034
AKAI
016
043
047
048
125
146
001
012
013
101
106
114
046
124
LG
AMPRO
072
ANAM
031
033
103
AUDIO DYNAMICS
012
023
039
BROKSONIC
035
037
129
CANON
028
031
033
CAPEHART
108
CRAIG
003
040
135
CURTIS MATHES
031
033
041
DAEWOO
005
007
010
064
065
108
110
111
112
116
117
119
043
(GOLDSTAR)
Brand
039
108
TATUNG
039
043
PULSAR
072
TEAC
034
039
043
020
QUARTZ
011
014
TECHNICS
031
033
070
123
QUASAR
033
066
075
145
TEKNIKA
019
031
033
034
RCA
013
020
033
034
034
LXI
003
009
013
014
040
041
062
063
THOMAS
034
017
034
101
106
107
109
140
144
TMK
006
145
147
TOSHIBA
008
013
042
047
003
008
010
014
059
082
112
131
031
033
034
040
TOTEVISION
040
101
053
054
101
UNITECH
040
MAGIN
040
MAGNAVOX
031
033
067
068
012
031
034
033
041
REALISTIC
067
RICO
058
VECTOR RESEARCH
012
MARTA
101
RUNCO
148
VICTOR
048
MATSUI
027
030
SALORA
014
VIDEO CONCEPTS
012
MEI
031
033
SAMSUNG
032
040
102
104
VIDEOSONIC
040
MEMOREX
003
010
014
031
105
107
109
112
WARDS
033
034
053
072
113
115
120
122
101
102
134
139
125
059
DBX
012
023
DYNATECH
034
053
ELECTROHOME
059
EMERSON
006
017
025
027
MGA
045
046
029
031
034
035
MINOLTA
013
020
036
037
046
101
MITSUBISHI
013
020
045
046
129
131
138
153
049
051
059
061
FISHER
003
008
009
010
151
FUNAI
034
GE
031
033
063
107
109
144
GO VIDEO
132
136
HARMAN KARDON
012
045
HITACHI
004
018
026
043
063
137
INSTANTREPLAY
031
033
JCL
031
033
JCPENNY
012
013
015
040
066
101
014
ZENITH
034
048
056
102
134
058
072
080
101
017
037
112
008
009
SCOTT
131
017
020
147
NEC
012
023
031
042
073
081
054
149
039
043
048
101
NORDMENDE
043
034
OPTONICA
053
054
150
PANASONIC
066
070
074
133
140
145
013
020
031
152
043
129
014
150
131
010
013
130
054
007
010
060
053
003
034
055
040
SANYO
024
050
034
039
MULTITECH
048
033
034
072
043
031
012
009
033
024
YAMAHA
00
031
017
135
003
012
013
048
SEARS
JVC
003
043
040
033
046
022
034
PENTAX
034
SANSUI
MTC
043
101
069
108
JENSEN
Codes
LLOYD
MARANTZ
043
Brand
PORTLAND
043
DAYTRON
039
Codes
083
031
034
067
PHILIPS
031
033
034
067
071
101
PILOT
101
PIONEER
013
Brand
Codes
GOLDEN CHANNEL
030
HAMLIN
049
050
021
031
SHINTOM
024
SONY
003
009
031
052
056
057
058
076
077
078
149
033
034
033
063
PHILCO
SHARP
054
SOUNDESIGN
034
STS
013
SYLVANIA
031
059
067
048
SYMPHONIC
034
TANDY
010
034
CATV
CATV
Brand
Codes
ABC
003
004
039
046
052
053
042
Brand
Brand
Codes
SL MARX
030
SPRUCER
047
078
076
STARCOM
002
004
POST NEWS WEEK
016
STARGATE
008
030
SYLVANIA
067
TADIRAN
030
TAEKWANG
110
PIONEER
055
Codes
065
085
090
034
051
052
AJIN
112
HITACHI
052
055
ANTRONIK
014
HOSPITALITY
070
077
ARCHER
005
JERROLD
002
003
004
008
PRUCER
059
CABLE STAR
026
009
010
052
069
PTS
011
048
CENTURION
092
074
073
074
CENTURY
007
LG
CITIZEN
007
M-NET
COLOUR VOICE
065
090
COMBANO
080
COMTRONICS
019
DIAMOND
023
EAGLE
020
030
040
EASTERN
057
062
066
ELECTRICORD
032
OAK
016
031
GE
072
PANASONIC
044
047
GEMINI
008
022
PARAGON
100
GI
052
074
PHILIPS
006
007
014
024
071
063
072
PULSAR
100
TAIHAN
105
037
RCA
047
TANDY
017
MACOM
033
REGAL
049
TEXSCAN
029
067
081
MAGNAVOX
010
REGENCY
057
TOCOM
039
040
056
030
MEMOREX
100
REMBRANT
025
TOSHIBA
100
MOVIE TIME
028
032
RK
091
UNIKA
007
014
024
NSC
015
028
SAMSUNG
102
107
030
068
UNITED CABLE
004
053
SCIENTIFIC ATLANTA
003
011
041
042
UNIVERSAL
005
007
014
024
043
045
046
026
027
032
035
012
015
018
086
087
088
089
100
114
060
025
(GOLDSTAR)
001
106
012
101
064
038
005
079
071
073
054
012
037
013
053
020
SHERITECH
022
SIGNAL
030
SIGNATURE
052
050
VIEWSTAR
ZENITH
093
43
Programming
Codes
STB
STB
Brand
Codes
Brand
Codes
Brand
Codes
Brand
Codes
ALPHASTAR DSR
123
EUROPLUS
114
MEMOREX
057
STARCAST
041
AMPLICA
050
FUJITSU
017
021
NEXTWAVE
028
124
SUPER GUIDE
020
124
125
BIRDVIEW
051
133
134
NORSAT
069
070
TEECOM
023
026
075
087
BSR
053
GENERAL INSTRUMENT 003
004
016
PACE SKY SATELLITE
143
088
090
107
130
CAPETRONICS
053
031
059
101
PANASONIC
060
CHANNEL MASTER
013
014
HITACHI
139
140
PANSAT
121
036
055
HOUSTON TRACKER
033
037
CHAPARRAL
008
009
057
104
CITOH
054
CURTIS MATHES
050
145
DRAKE
005
006
007
011
052
112
126
129
015
012
018
077
022
039
027
029
051
PERSONAL CABLE
002
127
UNIDEN
016
025
042
043
071
044
045
048
049
078
079
080
086
083
084
066
092
105
HYTEK
053
PRESIDENT
019
102
010
JANIEL
060
PRIMESTAR
030
110
116
JERROLD
061
PROSAT
072
KATHREIN
108
RCA
066
DX ANTENNA
024
046
056
076
LEGEND
057
REALISTIC
043
ECHOSTAR
038
040
057
058
LG
001
SAMSUNG
123
093
094
095
096
LUTRON
132
SATELLITE SERVICE CO 028
097
098
099
100
LUXOR
062
144
MACOM
010
059
101
UNIDEN
135
VIEWSTAR
115
106
WINEGARD
128
146
074
ZENITH
081
082
091
120
035
111
047
136
057
085
SCIENTIFIC ATLANTA
032
065
SONY
103
Brand
Codes
Brand
Codes
089
TOSHIBA
PHILIPS
PICO
122
137
117
068
141
ELECTRO HOME
142
HUGHES
147
125
063
064
138
Audio
Brand
Codes
AIWA
014
028
070
096
JVC
004
013
141
PHILIPS
026
112
143
253
125
129
139
229
KEC
185
186
187
PIONEER
039
042
043
063
TOSHIBA
137
KENWOOD
038
050
067
089
065
091
093
094
THE
061
170
171
197
206
115
123
127
250
VICTOR
088
215
222
230
AKAI
163
ANAM
003
014
017
023
059
106
189
216
217
235
236
Brand
113
WARDS
089
RCA
080
YAMAHA
054
RCX
092
030
NAD
045
046
LOTTE
014
016
036
098
REALISTIC
103
106
SAMSUNG
124
145
146
182
252
CARVER
086
100
172
173
174
CLARION
199
175
176
177
178
193
194
195
203
DAEWOO
027
053
060
084
179
180
181
183
204
244
245
246
102
148
198
221
201
202
208
213
SANSUI
011
135
138
144
DENON
015
075
130
143
214
219
223
232
SANYO
019
083
234
FANTASIA
071
238
240
SCOTT
106
186
FINEARTS
022
SHARP
031
032
051
052
FISHER
089
099
072
082
117
119
LG(GOLDSTAR)
001
021
024
029
199
200
087
107
108
190
191
192
211
212
239
034
035
188
HAITAI
LXI
103
MAGNAVOX
111
MARANTZ
002
018
020
025
156
184
110
034
041
081
090
206
209
210
097
112
SHERWOOD
005
006
158
SONY
044
045
109
114
118
126
248
249
012
020
073
074
076
077
105
161
222
HARMAN/KARDON 068
INKEL
MCS
104
MEMOREX
107
TAEKWANG
218
131
055
199
BURMECTER
049
147
QUASAR
KOHEL
MCINTOSH
Codes
037
058
062
069
NAD
046
078
079
095
121
ONKYO
013
040
041
047
162
163
164
165
122
149
150
151
048
056
057
132
166
167
168
169
152
153
154
155
133
140
205
231
233
242
157
158
159
160
OPTIMUS
158
189
207
222
224
PANASONIC
007
033
064
113
010
085
106
136
225
226
227
243
142
220
241
251
185
187
237
101
113
128
254
TEAC
247
PENNEY
104
TECHNICS
Brand
Codes
Brand
Codes
Brand
Codes
Brand
Codes
APEX DIGITAL
022
MAGNAVOX
013
PHILIPS
013
SONY
007
DENON
020
014
MARANTZ
024
PIONEER
004
THOMPSON
005
006
GE
005
006
MITSUBISHI
002
PROCEED
021
TOSHIBA
019
008
HARMAN KARDON 027
NAD
023
PROSCAN
005
006
YAMAHA
009
018
JVC
012
ONKYO
008
017
RCA
005
006
ZENITH
010
016
LG
001
PANASONIC
003
009
SAMSUNG
011
015
134
DVD
44
010
016
025
026
025
Note
45
Note
46
Troubleshooting
check list
Symptoms
No
picture,
no
Sound
sound
OK, poor picture
Picture
OK, poor sound
Picture blurred
Lines
or
streaks in
Poor
picture
reception
on some
channels
No colour
Poor colour
Remote control does not work
Incorrect
position
Vertical bars
or
stripes
on
background
Horizontal noise
Signal
Cable message appears
Check these items and try to
adjust these
The mains plug-(plugged in and
switched on)
Is the TV switched
Try
on
another channel
(weak signal)
Check aerial
(plugged
into
Check aerial
(broken lead?)
TV?)
Check aerial
Check for local interference
Adjust
contrast
Adjust brightness
Adjust
colour
Adjust
volume
Check the batteries in remote control
Check Audio/Video sockets
Auto-configure
or
adjust
(VCR only)
the H/V
position
Auto-configure
or
adjust
Clock
Auto-configure
or
adjust
Clock Phase
Is the
Signal
Cable connected
or
loose
47
Download PDF

advertising